Professional Documents
Culture Documents
Vturn Range Profile
Vturn Range Profile
VictorTaichung
R
VictorTaichung
Vturn-16 / 20 / 26
Entry model for reliable heavy cutting.
● Box slideways with hardness HRC 55 for heavy cutting.
● Genuine 45˚ slant bed for minimum distance from Z-axis ball screw
to the tool tip.
● Hydraulic 6"/8"/10" chuck is offered as standard.
● Programmable tailstock and chip conveyor is offered as standard.
● Wide range spindle motor Fanuc αPi is installed to offer high
for Vturn-26/110.
● Special LSB option on Vturn-26 for bar capacity
91mm/2500rpm.
VturnII-16 / 20
Available with upgraded servo turret,
built-in spindle, C-axis, and rear chips
disposal.
● Genuine 30˚ one piece slant bed enables large turning
diameter 440mm.
● Box slideways with power full spindle motor 11/15kW for
heavy cutting.
● Servo driven turret for quick tool indexing.
● Right or Rear chip disposal.
● Servo driven turret for quick tool indexing.
● C-axis available with built-in spindle allows faster
1
Vturn-36
2-step gearbox for heavy cutting.
● Box slideways with hardness HRC 55 for heavy cutting.
● Genuine 45˚ slant bed for minimum distance from Z-axis ball
screw to the tool tip.
● Hydraulic 12" chuck is offered as standard.
● 2-step gearbox is included to further enhance the cutting
VDI turret.
● Special LSB option with spindle nose A2-11 for bar capacity
160mm /1300rpm.
Vturn-45.
● Spindle nose A2-11.
● 2-step gearbox is included to further enhance the cutting
2
Headstock machining & boring:
To ensure the quality control on the accurate parts such like
headstock and spindle, Victor Taichung has developed
their own spindle boring machines to ensure long service
life for bearing installation.
Machine design:
Through the use of advanced CAD and CAE systems, our
R&D laboratory makes computer simulations of structures to
test for deformation and vibration characteristics which can later
be confirmed by computer aided testing.
3
Hardened box slide ways:
Cast-in slide ways for maximum rigidity. Nodular grey cast iron offers
ideal friction properties without sacrificing toughness. Heat treated
using high frequency induction heating to produce a wrap around
structure with hard wear resistance surface & tough internal
core. A depth of 0.5mm for maximum wear resistance,
ensuring accuracies are held throughout machine life.
The carriage:
To ensure smooth and accurate operation
of the carriage along the slideway Victor
employs the traditional craftsmanship
of hand scraping by skilled technicians.
This produces large contact areas for
improved stability in machining.
Add to this hand finished lubrication
channels for improved lubrication
properties to ensure the carriages benefit
from traditional methods of manufacture.
Machine assembly:
With the philosophy that quality must be built
in not inspected in, moving pallet assembly lines
are employed so that each machine can be closely
monitored and controlled long before it reaches the QC
department.
This is maintained by encouraging one person to be fully
responsible for the quality of each station as it progresses.
Quality inspection:
Every machine that leaves the factory floor has
passed numerous inspection procedures to achieve
vigorous demands of our customers.
4
Vturn-16,
Vturn-20 & Vturn-26
Cost-effective model for reliable heavy
cutting!
● Genuine 45˚ slant bed for minimum distance from Z-axis ball screw to the tool tip.
● Box slideways with hardness HRC 55 for heavy cutting.
● Hydraulic 6" /8" /10" chuck is offered as standard.
● Only wide range spindle motor Fanuc αPi is installed to offer high cutting force at
low rpm.
● Z-axis ball screw diameter 40mm for heavy cutting and high reliability.
● Maximum turning length 610mm for Vturn-16/20 and 1090mm for Vturn-26/110.
Angular thrusts
bearings
P1 P1
T1 T1
T3 T3
P2 P2 T2 T2
P3 P3
T4 T4
P4 P4
S1 S1
S2 S2S3 S3 S4 S4 RPM
RPM S1 S1
S2 S2S3 S3 S4 S4 RPM
RPM
P1 (*30 min. in low winding) S1 (base RPM in low winding) T1 (*30 min. in low winding) S1 (base RPM in low winding)
P2 (cont. in low winding) S2 (base RPM in high winding) T2 (cont. in low winding) S2 (base RPM in high winding)
P3 (*30 min. in high winding) S3 (max. RPM in low winding) T3 (*30 min. in high winding) S3 (max. RPM in low winding)
P4 (cont. in high winding) S4 (max. RPM in high winding) T4 (cont. in high winding) S4 (max. RPM in high winding)
*30 min. may be replaced by 15%, 15 min or 20 min. according to Fanuc technical specification
5
Genuine slant bed
Vturn series lathes have the Z-axis ballscrew mounted on the slant
bed (P1) instead of machine base (P2) to minimize the distance from
ballscrew to the tool insert and thus upgrades the turret and carriage
stiffness.
P1 P2
L1
ballscrew ballscrew
L2
Genuine Pseudo (By triangular
carriage)
6
VturnII-16 & VturnII-20
Available with upgraded servo turret, built-in
spindle, C-axis, and rear chips disposal
● Genuine 30˚ one piece slant bed enables large turning diameter 440mm.
● Box slideways with power full spindle motor 11/15kW for heavy cutting.
● Servo driven turret for quick tool indexing.
● C-axis available with built-in spindle allows faster acceleration time and less
P1 P1
T1 T1
T3 T3
P2 P2 T2 T2
P3 P3
T4 T4
P4 P4
S1 S1
S2 S2S3 S3 S4 S4 RPM
RPM S1 S1
S2 S2S3 S3 S4 S4 RPM
RPM
P1 (*30 min. in low winding) S1 (base RPM in low winding) T1 (*30 min. in low winding) S1 (base RPM in low winding)
P2 (cont. in low winding) S2 (base RPM in high winding) T2 (cont. in low winding) S2 (base RPM in high winding)
P3 (*30 min. in high winding) S3 (max. RPM in low winding) T3 (*30 min. in high winding) S3 (max. RPM in low winding)
P4 (cont. in high winding) S4 (max. RPM in high winding) T4 (cont. in high winding) S4 (max. RPM in high winding)
*30 min. may be replaced by 15%, 15 min or 20 min. according to Fanuc technical specification
Max.
Spindle P. Cont. Tor. Cont.
Model Base Speed (rpm) Speed P. (kW) Tor. (kg-m)
Motor (kW) (kg-m)
(rpm)
Low winding 500 1500 7.5 15 (15 min.) 14.6 29.2 (15 min.)
VturnII-16 aP22i
High winding 750 6000 11 15 (30 min.) 14.4 19.6 (30 min.)
Low winding 500 1500 5 9 (15 min.) 9.73 17.5 (15 min.)
Opt. αP15i
High winding 750 6000 7.5 9 (30 min.) 9.73 11.67 (30 min.)
Low winding 350 1050 7.5 15 (15 min.) 20.84 41.69 (15 min.)
VturnII-20 αP22i
High winding 525 4200 11 15 (30 min.) 20.52 27.98 (30 min.)
Low winding 350 1050 5 9 (15 min.) 13.9 25 (15 min.)
Opt. aP15i
High winding 525 4200 7.5 9 (30 min.) 13.9 16.68 (30 min.)
Low winding 300 900 5.5 7.5 (15%) 17.8 24.3 (15%)
VturnII-16CV aB160Mi
High winding 850 6000 11 18.5 (15%) 12.6 21.2 (15%)
Low winding 450 800 11 15 (20 min.) 23.8 32.4 (20 min.)
VturnII-20CV aB180Mi
High winding 800 4200 11 15 (30 min.) 13.3 18.2 (30 min.)
7
Servo Driven Turret for Faster Indexing
● Fast tool indexing time 0.2 seconds using servo driven turret.
● Available with Victor Taichung's own milling turret in conjunction
with servo motor to offer a near constant torque output over the
complete speed range up to 3000rpm.
● 12 station VDI turret with 12 live tool pockets allows quick tool
operation.
● To ensure perfect alignment in the machine structure, the bed is
traditional side for easy cleaning or from rear of the machine to link with
robot application.
8
Vturn-36
Two step gearbox for reliable
heavy cutting!
● Genuine 45˚ slant bed for minimum distance from Z-axis ball screw to the tool tip.
● Z-axis ballscrew diameter 50mm.
● 91mm bar capacity.
● 2-step gearbox is included to further enhance the cutting torque at low rpm.
● Maximum turning length 855mm for Vturn-36/85 and 1255mm for Vturn-36/125.
● Available with C-axis spindle and live tooling by Victor's own VDI turret.
● Special LSB option with spindle nose A2-11 for bar capacity 160mm/1300rpm.
2-step gearbox
20
Power (kW)
37kw S1 Cont 30
g -m g -m Continuous rating 30 30
k k 25
77 .7
10 25 15
Power (kw)
15
300 650
600
Torque (N-m)
1
981Nm S1 Cont 543Nm S1 Cont
10 100 1000 2500 800
400
661
Spindle Speed (r.p.m) 544
215Nm
400
200
FANUC motor α 22i 95
360 177Nm 80
650
0 200 300 400 650
0 1000 2000 2500
9 Motor speed (min -1 )
Motor speed (min -1 )
C-axis VDI turret with live tooling (CV option.)
● Live tooling is provided through the use of VDI turret that not only
provide an international tooling system but also allows for quick and
simple tool mounting.
● Coupling specification DIN-5480.
● Milling power 7kW/2500rpm.
- m .5k
160mm/1300rpm (optional) 7 kg 53
5 8. g-
m
● Large bore spindle with bar capacity of 160mm. 4 18 6k
.
3 1 59
● Ideal for machining of large diameter pipes.
2
● Max. spindle speed: 1800rpm (1300rpm limited by pneumatic chuck).
● Bearing diameter 220mm. 1
10 100 1000 1300
● Standard 18" Pneumatic chuck at front and manual chuck at rear of Spindle Speed (r.p.m)
spindle for extra stability during bar turning. FANUC motor α 22i
10
Vturn-40 & Vturn-45
3.25 meter lathe with gearbox and high feed
rate for heavy cutting!
● Genuine 45˚ one piece slant bed for maximal structure rigidity.
● Maximum turning length up to 3250mm (128").
● Rapid feed rate 20/20 m/min for Vturn-40/220 & Vturn-45/220.
● 2-step gearbox is included to further enhance the cutting torque at low rpm.
● Bar capacity : 91mm (3.58") for Vturn-40, 117.5mm (4.62") for Vturn-45.
2-step gearbox
25
Power (kW)
25
37kw S1 Cont 30
Power (kw)
Power (kw)
20 20 30 30
15 15 25
10 10 15 15
5 5
300 650
0 286 1000 2000 2500 0 728 1000 2000 2500 0 200 360 400 650 0 1000 2000 2500
Spindle Speed (r.p.m) Spindle Speed (r.p.m) Motor speed (min -1 ) Motor speed (min -1 )
1235
1200 500 1600
800
485 30min operating zone 661Nm S2 30min
1000 1432Nm S3 15min
30min operating zone 400
394 1200 1194Nm S2 30min
Torque (N-m)
800 600
Torque (N-m)
300
600 981Nm S1 Cont
Torque (N-m)
Torque (N-m)
11
One piece cast bed C-axis VDI or BMT turret with live tooling
● Builtin the latest technology, the new Vturn-40 and Vturn-45 have ● DDS built-in spindle (for Vturn-40CV and Vturn-40Y).
one-piece slant bed to enhance the structure stiffness.
● The turret carriage has even been enhanced 15% structure rigidity
Vturn-40/220
Vturn-45/325
12
Vturn-46
Built-in 4-Step Gearbox for powerful heavy
cutting!
● Genuine 60˚ slant bed for minimum distance from Z-axis ball screw to the
tool tip so as to reduce the chip built-up.
● Built-in 4-step gearbox inside the headstock further enhances the cutting
● Available with C-axis spindle and live tooling by Victor's own VDI turret.
4-step gearbox
20 22KW
kg
m
4
g-
6.
4k
53
g-
-m
0.
9k
kg
12
4.
10
.7
Power (kw)
43
97
m
5
g-
9k
4
m
0.
g-
25
3
2k
3.
-m
20
kg
2
-m
.2
56
kg
.6
45
1
10 100 1000 1500
13
C-axis VDI turret with live tooling
(CV option.)
● Live tooling is provided through the use of VDI turret
which not only provides an international tooling
system but also allows for quick and simple tool
mounting.
● Cf-axis design with angular encoder is included as
Powerful tailstock
● Built-inbearings for fixed center.
● MT#5 tailstock for powerful engagement.
14
Standard Accessories
Reliable Fanuc CNC control
● The proven reliability of Fanuc 0i-T control is combined with
Victor Taichung own PLC to offer customers an entire control
system who reliability is second to none.
Programmable tailstock
● Mounted on slideways for maximum clamping stability.
● Hydraulic clamping to bed with variable hydraulic pressure to
tailstock quill.
● Smooth tow along action by turret and programmable by
M-codes.
15
Optional Accessories
Tool Presetter (Renishaw®) Parts catcher & parts conveyor
● No longer to perform tedious time consuming cuts to determine To enhance the machines productivity a parts catcher is available to
tool geometry, the operator needs only to touch the tool tip to work in conjunction with the bar feed system.
the tool presetter sensor to get the tool geometries not only The parts catcher is fully programmable to allow automated running
reducing tool set-up time, but reducing down time due to tool with finished parts being dispensed in collection tray in door
breakage. compartment. Door flap is used to seal door off from swarf during
● Manual tool presetter (MTP): Arm is rotated manually. contamination.
● Auto tool presetter (ATP): Arm is rotated automatically by Note: Parts catcher not available for Vturn-46 For heavier parts a
programming. rotary chute system mounted below the spindle is used.
16
Machine Specifications
Vturn-16 VturnII-16 Vturn-26/60 (HD) Vturn-36/85
ITEM \ MODEL
Vturn-20 VturnII-20 Vturn-26/110 (HD) Vturn-36/125
MACHINE CAPACITY
Swing over bed mm 450 590 520 650
SPINDLE
Spindle nose (chuck) inch A2-5 (6") A2-5 (6") A2-8 (10") A2-8 (12")
A2-6 (8") A2-6 (8") (A2-11 for CV, LSB)
Max. spindle speed rpm 6000 6000 3500 2500
4200 (opt. 3500) 4200 (opt. 2500) (opt. 2000)
Spindle motor power kW 7.5 / 9.0 11 / 15 15 / 18.5 22 / 26 (opt. 30 / 37)
(opt. 7.5 / 9) (18.5 / 22) With gearbox
Bearing inside dia. mm 90 90 130 (160 for LSB) 160 (220 for LSB)
100 100
Spindle bore mm 52 52 87 (105 for LSB) 105 (160 for LSB)
62 62
TURRET
No. of tools no. 12 12 10 10
10 (opt. 8) 10 (opt. 8) (12 for CV)
No. of live tools no. - 12 - 6
2500
30 / 37 with gearbox
(37/45 CV/YCM)
2000
30 / 37
With gearbox
1500
30 / 37
With gearbox
Machine Color Options
160 190 (220 for LSB) 180
RAL 2008 (Victor's orange)
105 135 (160 for LSB) 123
32 32 32
50 (VDI-50) 50 60 (VDI-50)
1 1 1
3000 - 3000
7.0 - 7.0 RAL 7024 (Graphite grey)
18
Milling Spindle Output
VturnII-16/20CV Vturn-36CV/40CV/40YCM/46CV
40 90
Maximum Torque=35 Nm Maximum Torque=83 Nm
35 80
70
30
Torque (Nm)
Torque (Nm)
Intermittent Operating
60
25 Intermittent Operating
50
20
40
15 Stall Torque=30 Nm
Stall Torque=12 Nm 30
10 20
Continuous Operating Continuous Operating
5 10
19
Victor's Fanuc 0i-TF/32i-B Control Specifications
Standard:
ITEM SPECIFICATION DESCRIPTION
Controlled Axes:
1. Controlled Axes 2 Axes (X, Z) 10. S Code Function S5 digit
Position/Linear interpolation/Circular 11. T Code Function T2 digit
2. Simultaneous Controlled Axes interpolation (2/2/2)
12. Rigid Tapping (Spindle) Std.
3. Least Input Increment 0.001mm / 0.0001 inch / 0.001 deg.
4. Least Input Increment 1/10 0.0001mm / 0.00001 inch / 0.0001 deg. Tool Function & Tool Compensation:
5. Max, command value ±99999.999mm(±9999.9999in) 1. Tool Function T7+1/T6+2digits
6. Fine Acceleration & Deceleration Control Std. 2. Tool Offset Pairs ±6-digit 64 pairs
7. HRV Control Std. 3. Tool Nose Radius Compensation Std. (G40/G41/G42)
8. Inch / Metric Conversion Std.(G20/G21) 4. Tool Geometry/wear Compensation Std.
9. Interlock All Axes / Each Axis / Cutting Block Start 5. Number of Tool Offsets (in total) 64 sets
10. Machine Lock All Axes / Each Axis 6. Automatic Tool Offset Std.
11. Emergency Stop Std. 7. Direct Input of Tool Offset Value Measured B Std.
12. Over-travel Std.
Accuracy Compensation:
13. Stored Stroke Check 1 Std.
1. Backlash Compensation Rapid Traverse / Cutting Feed
14. Mirror Image Each Axis
2. Stored Pitch Error Compensation Std.
15. Chamfering on/off Std.
16. Follow-up Std. Edit Operation:
17. Unexpected disturbance torque detection function Std. (to be used to tool load monitoring) 1. Part Program Storage Length (in total) 1280m/512kB (0i-F/32iB)
18. Position switch (with Victor's own PLC) Std. (to be used for security) 2. Number of Registerable programs (in total) 400 (0i-F), 400 (32iB).
Operation: 3. Part Program Editing Std.
4. Program Protect Std.
1. Automatic Operation Std.
5. Background Editing Std.
2. MDI Operation MDI B
6. Memory card editing Std.
3. DNC Operation Reader / Puncher Interface is Required
4. DNC Operation with Memory Card PCMCIA Card Attachment is Required Setting and Display:
5. Program Number Search Std. 1. Status Display Std.
6. Sequence Number Search Std. 2. Clock Function Std.
7. Sequence number comparison and stop Std. 3. Current Position Display Std.
8. Buffer Register Std. 4. Program Display Program name 31 characters
9. Dry Run Std. 5. Parameter Setting and Display Std.
10. Single Block Std. 6. Self Diagnosis Function Std.
11. JOG Feed Std. 7. Alarm Display Std.
12. Manual Reference Position Return Std. 8. Alarm History Display 25
13. Manual Handle Feed 1 Unit / Each Path 9. Operation History Display Std.
14. Manual Handle Feed Rate X1, X10, X100 10. Help Function Std.
Interpolation: 11. Run Hour and Parts Count Display Std.
12. Actual Cutting Feedrate Display Std.
1. Positioning G00
13. Display Spindle Speed and T Code At All Screens Std.
2. Threading synchronous cutting Std.
14. Dynamic Graphic Display Std.
3. Multiple threading Std.
15. Servo Setting Screen Std.
4. Threading retract Std.
16. Display of Hardware and Software Configuration Std.
5. Continuous threading Std. (G76)
17. Multi-Language Display Std.
6. Variable threading Std. (G34)
18. Data Protection Key Std.
7. Linear Interpolation G01
19. Erase CRT Screen Display Std.
8. Circular Interpolation G02, G03 (multi-quadrant is possible).
20. Spindle Setting Screen Std.
9. Dwell G04
21. Color LCD / MDI 8.4" (0i), 10.4" (0i-F*1/32iB)
10. Skip Function G31
11. Reference Position Return G28 Data Input / Output:
12. Reference Position Return Check G27 1. Reader / Puncher Interface RS-232 interface
13. 2ND Reference Position Return Std. 2. Memory Card Interface Std.
Feed: 3. External Work piece number search 9999
20
Technical Drawings
Vturn II-16 142 510
Z-axis stroke
ø32 ø40 460 50
ø32 ø195 Z-axis zero point
ø1
ø187
0
30
3535 ø44
ø510 20 ø181 ø370
X-axiszeropoint
14
X-axis stroke
ø2
220
240
235
ø184
30
ø32
45
20
20
ø40 ø46
15
ø2
220 20 56 81 29
6"Powerchuck
185 35 240 135 448 62 35 (104)
X-axis stroke 160 80 440
440
Quilltaper stroke oftailstock Strokeof tailstock
Z-axis stroke
5039.5 68 460 50
ø1
157.5
ø2
94
ø20
ø2 80
13 ø3
30 65
5
20
ø31 ø5 30
ø3
X-axis stroke
135
140
160
70
170
5
238
49
240
10
105
8
43
50
9
ø1
ø18
10
20.5
20 40 56 81 29 169.5 42
6"Power chuck
65 30 135 105 133 310 42 78 25 55 37 (104)
157.5 230 160 80 440
240 Quill taper stroke of tailstock Stroke of tailstock
X-axis stroke
ø40
6
ø22
60
ø4
ø2 40 40
1 ø3
ø23
40
66
X-axis zero point
25
20
X-axisstroke
ø5
235
240
220
ø2
45
ø40 40 18
30 25
20
55
ø2 65 91 39
8"Power chuck
180 40 20 145 448 62 35 (104)
220
240 170 80 440
X-axis stroke Quill taper stroke of tailstock Stroke of tailstock
Z-axis stroke
ø1
5039.5 68 460 50
Z-axis zero point
10 40
5
ø17
ø2
157.5
94
ø20
ø2 80
13 ø3
30 65
5
20
ø31 ø5 30
05 ø3
ø2
X-axis stroke
135
140
7
160
170
0
5
238
49
240
10
105
8
43
50
9
ø1
ø18
10
20.5
20 40 56 81 29 169.5 42
65 30 135 105 6"Power chuck
133 310 42 78 25 55 37 (104)
157.5 230 160 80 440
240 Quill taper stroke of tailstock Stroke of tailstock
X-axis stroke
21
Technical Drawings
Vturn-16
50 90 600 Z-Axis Travel
ø1
93 550 Z-Axis zero point 50
35
5 75 5 75
35 30
35 30
5
X-Axis stroke
84
30 ø4
115
ø174 ø160
110
135
20
ø165
ø160
ø75
ø2
205
30
20
90
ø32 115 20 (6" Power chuck)
195 80 440
170 35 135 Quill stroke of tailstock Stroke of tailstock
X axis stroke
Standard tool (12-station)
Vturn-20
50 90 600 Z-Axis Travel
35 550 Z-Axis zero point 50
ø235
5 75 5 75
35 30
5
X-Axis stroke
20
ø23
0
115
110
30
135
84
ø2
ø4
16
ø160
ø75
ø210
ø1
60
20
103
115 20 8"Power chuck
ø32 195 80 440
Quill stroke of tailstock Stroke of tailstock
205 170 135
35 X axis stroke
Vturn-26
68 100 1090(610) Z axis travel
40
940(510) Z axis zero point 150(100)
ø287
ø32 ø50
R155
210
7
Standard turning dia
60 40
ø2
X axis travel
60
90
95
ø3
65
ø5
25
50 180
ø27
240
3
ø290
113 29
190 50 ø10"Power chuck
182 100 930(450) Stroke of tailstock
250 210 40 240 Quill stroke of tailstock
X axis stroke
Vturn-26HD
Ø50
40 168 1090(610) Z-axis travel
69
Ø2 940(510) Z-axis zero point 100
Ø287
Ø46
Ø32
7
25
455
Ø46
0
40
41
zero point
94
Ø
Ø3
X-axis
X-axis
Ø5
travel
65
255
180
24
25
Ø2
73
50
972(542) 52 16
113
10” power chuck
15
22
Technical Drawings
Vturn-36
45 70 111 1255(855) Z axis travel 110
ø3
240
8 1155(755) Z axis zero point 100
40
60 8
40
5
50
X axis zero point
50
160 115
ø550 Cutting dia max.
ø110
Standard turning dia
305
5
ø5
1
ø445
ø320
71 ø32
ø150
ø210
ø305
ø6
60
32
30
ø50 122 29
170 12" Power chuck
257 100 1030(630) Stroke of tailstock
240 40 275 30
Quill stroke of tailstock
305
X axis stroke
Vturn-36CV 150
70
1255(855)
1155(755)
Z-axis stroke
Z-axis zero point 100
82
388
198
100 112
212
ø50
60 SA
113
UT
73
ER ø249
ø50 175
761
X-axis stroke
573
57
89
119
ø
335
10
0 ø458 5
375
ø1
ø305(12”)
ø110
ø458
ø398
ø210
6
ø150
10
34 5530
ø292
64 55 199 156
42 3933
198 57 318 10 122 630 1333
385 257 100 1030(630)
X axis stroke Quill taper stroke of tailstock Stroke of tailstock
12
Vturn-40 (Vturn-45) ø4
143
ø7 600
49
160
ø
7
ø7 2100 [3150] Z axis zero point
290
8 100
20
20
20
7
37
ø620 Cutting dia max.
20
X axis stroke
ø6
ø ø5
40
Standard turning dia
zero point
310
310
340
ø380 (ø450)
20
ø32
ø520
30
30
150 125 83
ø150
ø200
ø377
149
ø3 35
44 (15"/18" Power chuck)
399 1975 [3025] Stroke of tailstock
170 310 30
290 340
X axis stroke [Vturn-40(45)/325]
ø3
Vturn-40CV
ø339.3
62
.2
120 57 198
90
ø242
30
X axis zero point
X-axis stroke
.2
ø3
ø3
ø50
540
90
342
352
70
Ø380
ø330
ø390
10
92
10
.1 150 125 73
ø150
7
200
ø 24
34 56 8 900 34
4
2. 64 56
15 149
.9
ø1 15"Power chuck
28
97
ø1
ø5
85
0
.8
352
X axis travel
23
Technical Drawings
Vturn-40YCM
45 45
33
56 56 22
25
7
27.5
Ø10.5 4-M12X
45
58.5
P1.75X24
120.041
45 45
25
33
A A
Ø56
Ø75
Ø251
Ø758
Ø64 Ø60 143
60
30
26
160
90
290
8 2100(3150) Z-axis zero point 100
20
20
33
Ø3
40
80 80
Zero point
310
310
32
Ø274 5 Ø223
13
Ø380
45°
Ø432
30
30
150 125 83
Ø150
40
Ø200
Ø520 2
10
6
Ø381(15-inch chuck)
7
Vturn-46
0 90 300 150 Quill stroke of tailstock 1415 Stroke of tailstock
ø34
112 1650 Z axis travel
1400 Z axis zero point 250
[Vturn-40(45)/325]
60 130
20
50 40 270
ø5 8
32
1
ø 33
50
50
50
60 103 125
ø5
13
365
305
ø7
390
417
85
95
30
ø381
ø60
35
25
150
100
365 25 149
270 40 390 15"Power chuck
X axis stroke
608
Vturn-46CV 8 2
ø2 300
148 1650 Z-axis travel
ø318 1400 Z-axis zero point 250
0
ø2
7 55
70
ø249 129
ø32 7043 85
198
30 89 255
70 44
68
61 ø5
80
X-axis zero point
608
ø7 28
ø4
0
70
10 97 125
155
ø50
234
10 330
ø381
ø1
50
100 95
6
58
60
186
40
ø292
238 945 330 100 120 120 35
34 55 30
90 331.5 150 1413.5 Stroke of tailstock
64 55 234 186 Quill taper of tailstock
198 57 353 10
420
X axis stroke
24
Machine Layout (excl. Transformer)
A B C 260
G
E
D
F
Vturn-P16 with built-in robot Vturn-A20Y with Y-axis Vturn-V560 vertical lathe
BMT turret
TEL: 04-24733326
profile:
Sales turnover: USD 155 mil's (in 2014)*
No. of employees: 1079
*Exchange rate: 1 USD=30 TWD.
15072801