Professional Documents
Culture Documents
PLT5 520
PLT5 520
PLT5 520
Version 0.3
PLT5 520
Features
• Optical output power (continuous wave): 30 / 50 mW (Tcase = 25 °C)
• Typical emission wavelength: 520 nm
• Efficient radiation source for cw and pulsed operation
• Single transverse mode semiconductor laser
• High modulation bandwidth
• TO56 package with photo diode
Applications
• Laser projection
• Laser shows
• Biomedical Applications
• Metrology
Safety Advice
Depending on the mode of operation, these devices emit highly concentrated visible light which can be
hazardous to the human eye. Products which incorporate these devices have to follow the safety
precautions found in IEC 60825-1 “Safety of laser products”.
23.05.2017 1
DRAFT - This design is for Reference only. Subject to change –
may be necessary in a limited number of cases.
Version 0.3 PLT5 520
Ordering Information
Type: Optical Output Power Ordering Code
Popt (Tcase = 25°C)
PLT5 520_B1-3 50 mW Q65111A5771
PLT5 520_B1-6 30 mW Q65111A6145
Maximum Ratings
Operation outside these conditions may damage the device. Operation at maximum ratings may influence
lifetime.
Parameter Symbol Values Unit
min. max.
Operating Current IF 200 mA
Operating Temperature Tcase - 20 + 60 °C
Storage Temperature Tstg - 40 + 85 °C
Reverse Voltage VR 2 V
Soldering Temperature max. 10 sec. Tsolder 260 °C
Junction temperature Tj 150 °C
23.05.2017 2
DRAFT - This design is for Reference only. Subject to change –
may be necessary in a limited number of cases.
Version 0.3 PLT5 520
23.05.2017 3
DRAFT - This design is for Reference only. Subject to change –
may be necessary in a limited number of cases.
Version 0.3 PLT5 520
60 40
Tcase= 0 °C
Tcase= 0 °C
50
Tcase= 20 °C Tcase= 20 °C
30
40
Popt [mW]
Popt [mW]
Tcase= 40 °C Tcase= 40 °C
30 20
Tcase= 60 °C
Tcase= 60 °C
20
10
10
0 0
0 50 100 150 200 0 50 100 150
IF [mA] IF [mA]
8.0 8.0
Tcase= 0 °C
Tcase= 0 °C
Tcase= 20 °C
Tcase= 20 °C
6.0 6.0
Tcase= 40 °C
Tcase= 40 °C
Tcase= 60 °C
Tcase= 60 °C
VF [V]
VF [V]
4.0 4.0
2.0 2.0
0.0 0.0
0 50 100 150 200 0 50 100 150 200
IF [mA] IF [mA]
23.05.2017 4
DRAFT - This design is for Reference only. Subject to change –
may be necessary in a limited number of cases.
Version 0.3 PLT5 520
75 200
70
180
65
B4-B6
B1-B3
60
160
Ith [mA]
IF [mA]
55
B4-B6
B1-B3
140
50
45
120
40
35 100
0 20 40 60 -20 0 20 40 60
Tcase= 40 °C
1.0 1.0
Tcase= 20 °C Tcase= 60 °C
0.8 0.8
||
Popt [a. u.]
0.6 0.6
0.4 0.4
⊥
0.2 0.2
0.0 0.0
514 516 518 520 522 -40 -20 0 20 40
[nm] [deg]
23.05.2017 5
DRAFT - This design is for Reference only. Subject to change –
may be necessary in a limited number of cases.
Version 0.3 PLT5 520
Package Outline
Dimensions in mm
Pin Connection
3 1 Pin 1: LD Cathode
Pin 2: LD Anode, PD Cathode (case)
Pin 3: PD Anode
PD LD
2
23.05.2017 6
DRAFT - This design is for Reference only. Subject to change –
may be necessary in a limited number of cases.
Version 0.3 PLT5 520
Tray
Dimensions in mm [inches]
23.05.2017 7
DRAFT - This design is for Reference only. Subject to change –
may be necessary in a limited number of cases.
Version 0.3 PLT5 520
Barcode-Product-Label (BPL)
EX
OSRAM Opto
pto LX XXXX BIN1: XX-XX-X-XXX-X
AM
Semiconductors
ctors
ors
RoHS Compliant
O: 12345
(6P) BATCH NO: 1234567890
1234567
67890
7890
PL
ML Temp ST
X XXX °C X
E
(1T) LOT NO: 1234567890 (9D)
(9D)
(9 C: 1234
9D)) D/C:
D/C 123
234
34
RXX
Pack: R
RX
DEMY XXX
XX
XX
X_X123_1234.1234
X_X123_1
X123
3_123
_123 4X
1234.1234
OHA04563
Barcode label
3: Q-1 -20
-20
Bin 2: P-1
Bin 1:
240 p ST
ED Bin
MY
PL 76
R07 ition C R
7 al RT
220
DE
TO Y T6
T
ML
TEX
2
lti LS
8
2a
R1
1
3
Q-
R:
1+
VA
Mu
CK
P-
PA
P:
OU
GR
(G)
44
: 01
tor to
8
99
s
nd Op
D/C
21
)
uc
00
(9D
co M
mi RA
21
00
4
20
:
NO
OS
23
Y:
H1
H
Se
QT
TC
3G
(Q)
BA
: 12
)
(6P
5
NO
2
14
T
LO
00
)
(1T
11:
NO
OD
PR
(X)
23.05.2017 8
DRAFT - This design is for Reference only. Subject to change –
may be necessary in a limited number of cases.
Version 0.3 PLT5 520
Disclaimer
OSRAM OS assumes no liability whatsoever for any use of this document or its content by recipient including, but not
limited to, for any design in activities based on this preliminary draft version. OSRAM OS may e. g. decide at its sole
discretion to stop developing and/or finalizing the underlying design at any time.
Attention please!
The information describes the type of component and shall not be considered as assured characteristics.
Terms of delivery and rights to change design reserved. Due to technical requirements components may contain
dangerous substances.
For information on the types in question please contact our Sales Organization.
If printed or downloaded, please find the latest version in the Internet.
Packing
Please use the recycling operators known to you. We can also help you – get in touch with your nearest sales office.
By agreement we will take packing material back, if it is sorted. You must bear the costs of transport. For packing
material that is returned to us unsorted or which we are not obliged to accept, we shall have to invoice you for any costs
incurred.
Components used in life-support devices or systems must be expressly authorized for such purpose!
Critical components* may only be used in life-support devices** or systems with the express written approval of
OSRAM OS.
*) A critical component is a component used in a life-support device or system whose failure can reasonably be
expected to cause the failure of that life-support device or system, or to affect its safety or the effectiveness of that
device or system.
**) Life support devices or systems are intended (a) to be implanted in the human body, or (b) to support and/or
maintain and sustain human life. If they fail, it is reasonable to assume that the health and the life of the user may be
endangered.
b) Mounting instructions
In order to maintain the lifetime of the laser diode proper heat management is essential. Due to the design of the laser
diode heat is dissipated only through the base plate of the diode‘s body. A proper heat conducting interconnection
between the diodes base plate and the heat sink must be maintained.
23.05.2017 9
DRAFT - This design is for Reference only. Subject to change –
may be necessary in a limited number of cases.
Version 0.3 PLT5 520
23.05.2017 10
DRAFT - This design is for Reference only. Subject to change –
may be necessary in a limited number of cases.