Professional Documents
Culture Documents
EC327 E Polyfuse PTC
EC327 E Polyfuse PTC
Max voltage 60V 60/250V 60/600V 15-30V 15-24V 15-20V 16V NA Specifications, descriptions and illustrative material in this literature are as accurate as known at the time of
publication, but are subject to change without notice.
NA = Not Available
5
PTC Characteristics LEAKAGE CURRENT: A PTC is said to TEMPERATURE DERATING: The useful PTC Applications When to apply a resettable PTC vs. a Systems Interface) Standard for this large Littelfuse offers a full range of battery required. The following are typical examples complete protection for the circuit. Contact
have “tripped” when it has transitioned upper limit for a PTC is generally 85°C while traditional fuse is always the choice of the market includes a statement that “....a strap, surface mount and radial leaded of circuits using POLYFUSE® resettable your location Littelfuse application expert
and Terminology from its low resistance state to a high the maximum operating temperature for PTCs are used as circuit protection in designer or technician but in some cases, Positive Temperature Coefficient device resettable PTC devices designed to protect PTCs in combination with other Littelfuse for additional design assistance or
resistance state due to overload current. fuses is 125°C. The following temperature applications where sensitive components PTC’s offer a convenient form of circuit must be used instead of a fuse, to limit the applications where overcurrent protection is circuit protection devices to provide visit www.littelfuse.com/PTCs.
A polymeric PTC (positive temperature
derating curves (see chart at bottom of are at risk of damage from overcurrent protection to improve the reliability of an maximum amount of current sourced”.
coefficient) overcurrent protector is an Protection is accomplished by limiting the page) that compare PTCs to fuses illustrate conditions. The ability of PTCs to reset application. There is an important area of
element placed in series with the circuit or current flow to a low leakage level. Leakage The application selection guide below should
that more derating is required for a PTC at a themselves after exposure to a fault current applications where the use of resettable
assembly to be protected. The PTC current can range from less than a hundred be used as an aid in selecting the proper Power Over Ethernet Li-ion Battery Pack
given temperature. makes them ideal for use in circuits that are fuses (PTCs) has become a requirement.
element protects the circuit by changing milliamps at rated voltage up to a few device for your end application. Please
not easily accessible to a user or technician. Much of the design work for personal Swtich/Hub Powered End Station
from a low-resistance to a high resistance hundred milliamps at lower voltages. Additional operating characteristics can be consult the datasheets on www.littelfuse.com
Typical applications include port protection computers and peripheral devices is Battery Connector Battery Controller IC
state in response to an overcurrent. The fuse on the other hand completely reviewed by the circuit designer in making for detailed technical specifications.
on personal computers (USB, Firewire, strongly influenced by the Microsoft and
This function is called “tripping” of the interrupts the current flow and this open the decision to choose a PTC or a fuse for keyboard/mouse, and serial ports), Intel System Design Guide which states
Data Pair Data Pair
Battery +
overcurrent protection device. circuit results in no leakage current after it overcurrent protection. peripherals (hard drives, video cards, and that “Using a fuse that must be replaced Battery -
Cell Phone
has been subjected to an overload current. hubs), cell phone, battery packs, industrial each time an overcurrent condition occurs is Control
Overcurrent circuit protection can be AGENCY APPROVALS: PTCs are
controls, lighting ballast and motor controls. unacceptable.” And the SCSI (Small Computer Power Source Powered
accomplished with the use of either a FAULT CURRENT: The PTC is rated for Recognized under the Component
Equipment Device
traditional fuse or the more recently a maximum short circuit current at rated Program of Underwriters Laboratories to (PSE) (PD) (3) V5.5MLA0402
voltage. This fault current level is the UL Standard 1434 for Thermistors. SURFACE MOUNT RADIAL LEADED BATTERY STRAP (AXIAL LEADED) (Multilayer
developed resettable PTC. Both devices Varistor)
maximum current that the device can safely The devices have also been approved for Series Name 0805L 1206L 1210L 1812L 2016L 2920L USBR 30R 60R 250R 600R ST LT LR VT VL Signal
function by reacting to the heat generated Application
Ground
by the excessive current flow in the circuit. limit keeping in mind that the PTC will not use in Canada by Underwriters Laboratories.
Ul60950 ,TIA-968-A, GR-1089 Requirements X X Data Pair Data Pair
The fuse element melts open, interrupting actually interrupt the current flow (see Approvals for fuses include Recognition Shield
ITU-T Recoomendations X X Ground
the current flow, while the PTC changes LEAKAGE CURRENT above). The typical under the Component Program of CPE (Customer Premises Equipment) X X
Telecom
from low resistance to high resistance short circuit rating of a board-mounted PTC Underwriters Laboratories and the CSA Analog Line Card X X
to limit current flow. The graph below is 40A; for battery strap PTCs, this value can Component Acceptance Program. In addition, T1/E1/J1 And HDSL X X
shows the response of the PTC device reach 100A. Fuses do in fact interrupt the many fuses are listed in accordance with ISDN X X
current flow in response to the overload and UL/CSA/ANCE (Mexico) 248-14, ADSL X X USB 1.1 USB 2.0
to temperature.
the range of interrupting ratings vary from Supplemental Fuses. Cable Telephony X X
PBX/KTS And Key Telephone System X X USB Port USB Controller USB Port USB Controller
tens of amperes up to 10,000 amperes at
rated voltage. RESISTANCE: Reviewing product CPU X X V5.5MLA0603 V5.5MLA063
specifications indicates that similarly-rated USB X X X X X
VBU VBUS
IEEE1284 Parallel Data Bus X X X X 1206L150 1206L150
OPERATING VOLTAGE RATING: PTCs have about twice (sometimes more) D+ D+
Outside World
Outside World
Computer
IEEE 802.3 X X X D- D-
General use PTCs are not rated above 60V the resistance of fuses.
IEEE 1394 X X X
Log resistance (ohms)
Electronics
Consumer
Smart Card Reader X
Mobile Phone X X X
Temperature Derating Curves Comparing PTCs to Fuses
Understanding the differences in Linear AC/DC Adapter X X X X X X X
performance between the two types of Chart Key C Portable Electronic Input Port X X X X X
140
devices will make the best circuit protection Curve A Electromagnetic Loads, Motor X X X X IEEE 1394 – FireWire Tip/Ring circuit – Metallic
choice easier. The most obvious difference Solenoid Protection X X X X
Thin-Film Fuses and 313 120
Battery
Series (.010 to .150A) A Lithium Cell X X X X X
is that the PTC is resettable. This is an 1394 Port 1394 Controller RJ11 Connector Tx/Rx Circuits
PERCENT OF RATING
B X X X X X
inherent characteristic in which the PTC Curve B 100 Battery Pack V33MLA1206
resets (returns to low resistance state) B
FLAT-PAK®, Telelink®, VBU
electronic
1812L110/33
Medical
after power is removed and the device Nano2®, PICO®, 80 TPA+ Tip
Outside World
Blade Terminal, Voltage / Current Input Terminal X X TPA-
cools down. There are a number of other
Special Purpose and A TPB+
Telco
operating characteristics that differentiate 600R Series SMD/leaded
60 TPB-
other leaded and 250R Series SIDACtor®
the two types of products. cartridge fuses
NOTE: The application summary is for reference only. Determination of suitability for a specific application is the responsibility of the customer. Device
25°C
(except 313.010 – .150A) 40
C Ring
The terminology used for PTCs is often
(4) PGB1010603 Signal Signal
similar but not the same as for fuses. Two Curve C 20 Ground Ground
(PulseGuard®
parameters that fall into this category are Resettable PTCs ESD Suppressor)
-60°C -40°C -20°C 0°C 20°C 40°C 60°C 80°C 100°C 120°C
leakage current and fault current rating. -76°F -40°F -4°F 32°F 68°F 104°F 140°F 176°F 212°F 248°F Shield
Ground
AMBIENT TEMPERATURE
2 3 4
Selection Process that the circuit parameters do not exceed 5. Check that the trip time protects
these ratings. the circuit.
1. Determine the following circuit operating
parameters: 4. Verify that the ambient operating 6. Verify that the post trip resistance (R1MAX)
• Normal operating current – IHOLD
temperature within close proximity to of the device is taken into account in the
• Maximum circuit voltage – VMAX the device is within its normal operating circuit design.
• Maximum interrupt current – IMAX range. Thermally derate IHOLD and IMAX as 7. Independently test and evaluate the
POLYFUSE® PTC SELECTION GUIDE
• Ambient operating temperature
necessary. See equation below. suitability and performance of the PTC
2. Select the suitable form factor.
in the actual application.
3. Compare the PTC data sheet ratings on IMAX World Headquarters
IHOLD =
littelfuse.com for VMAX and IMAX to ensure Thermal derating factor Littelfuse, Inc.
800 E. Northwest Highway
Des Plaines, IL 60016 USA
PTC Selection Table www.littelfuse.com
SURFACE MOUNT RADIAL LEADED
Series Name 0805L 1206L 1210L 1812L 2016L 2920L USBR 30R
Max voltage 60V 60/250V 60/600V 15-30V 15-24V 15-20V 16V NA Specifications, descriptions and illustrative material in this literature are as accurate as known at the time of
publication, but are subject to change without notice.
NA = Not Available
5
PTC Characteristics LEAKAGE CURRENT: A PTC is said to TEMPERATURE DERATING: The useful PTC Applications When to apply a resettable PTC vs. a Systems Interface) Standard for this large Littelfuse offers a full range of battery required. The following are typical examples complete protection for the circuit. Contact
have “tripped” when it has transitioned upper limit for a PTC is generally 85°C while traditional fuse is always the choice of the market includes a statement that “....a strap, surface mount and radial leaded of circuits using POLYFUSE® resettable your location Littelfuse application expert
and Terminology from its low resistance state to a high the maximum operating temperature for PTCs are used as circuit protection in designer or technician but in some cases, Positive Temperature Coefficient device resettable PTC devices designed to protect PTCs in combination with other Littelfuse for additional design assistance or
resistance state due to overload current. fuses is 125°C. The following temperature applications where sensitive components PTC’s offer a convenient form of circuit must be used instead of a fuse, to limit the applications where overcurrent protection is circuit protection devices to provide visit www.littelfuse.com/PTCs.
A polymeric PTC (positive temperature
derating curves (see chart at bottom of are at risk of damage from overcurrent protection to improve the reliability of an maximum amount of current sourced”.
coefficient) overcurrent protector is an Protection is accomplished by limiting the page) that compare PTCs to fuses illustrate conditions. The ability of PTCs to reset application. There is an important area of
element placed in series with the circuit or current flow to a low leakage level. Leakage The application selection guide below should
that more derating is required for a PTC at a themselves after exposure to a fault current applications where the use of resettable
assembly to be protected. The PTC current can range from less than a hundred be used as an aid in selecting the proper Power Over Ethernet Li-ion Battery Pack
given temperature. makes them ideal for use in circuits that are fuses (PTCs) has become a requirement.
element protects the circuit by changing milliamps at rated voltage up to a few device for your end application. Please
not easily accessible to a user or technician. Much of the design work for personal Swtich/Hub Powered End Station
from a low-resistance to a high resistance hundred milliamps at lower voltages. Additional operating characteristics can be consult the datasheets on www.littelfuse.com
Typical applications include port protection computers and peripheral devices is Battery Connector Battery Controller IC
state in response to an overcurrent. The fuse on the other hand completely reviewed by the circuit designer in making for detailed technical specifications.
on personal computers (USB, Firewire, strongly influenced by the Microsoft and
This function is called “tripping” of the interrupts the current flow and this open the decision to choose a PTC or a fuse for keyboard/mouse, and serial ports), Intel System Design Guide which states
Data Pair Data Pair
Battery +
overcurrent protection device. circuit results in no leakage current after it overcurrent protection. peripherals (hard drives, video cards, and that “Using a fuse that must be replaced Battery -
Cell Phone
has been subjected to an overload current. hubs), cell phone, battery packs, industrial each time an overcurrent condition occurs is Control
Overcurrent circuit protection can be AGENCY APPROVALS: PTCs are
controls, lighting ballast and motor controls. unacceptable.” And the SCSI (Small Computer Power Source Powered
accomplished with the use of either a FAULT CURRENT: The PTC is rated for Recognized under the Component
Equipment Device
traditional fuse or the more recently a maximum short circuit current at rated Program of Underwriters Laboratories to (PSE) (PD) (3) V5.5MLA0402
voltage. This fault current level is the UL Standard 1434 for Thermistors. SURFACE MOUNT RADIAL LEADED BATTERY STRAP (AXIAL LEADED) (Multilayer
developed resettable PTC. Both devices Varistor)
maximum current that the device can safely The devices have also been approved for Series Name 0805L 1206L 1210L 1812L 2016L 2920L USBR 30R 60R 250R 600R ST LT LR VT VL Signal
function by reacting to the heat generated Application
Ground
by the excessive current flow in the circuit. limit keeping in mind that the PTC will not use in Canada by Underwriters Laboratories.
Ul60950 ,TIA-968-A, GR-1089 Requirements X X Data Pair Data Pair
The fuse element melts open, interrupting actually interrupt the current flow (see Approvals for fuses include Recognition Shield
ITU-T Recoomendations X X Ground
the current flow, while the PTC changes LEAKAGE CURRENT above). The typical under the Component Program of CPE (Customer Premises Equipment) X X
Telecom
from low resistance to high resistance short circuit rating of a board-mounted PTC Underwriters Laboratories and the CSA Analog Line Card X X
to limit current flow. The graph below is 40A; for battery strap PTCs, this value can Component Acceptance Program. In addition, T1/E1/J1 And HDSL X X
shows the response of the PTC device reach 100A. Fuses do in fact interrupt the many fuses are listed in accordance with ISDN X X
current flow in response to the overload and UL/CSA/ANCE (Mexico) 248-14, ADSL X X USB 1.1 USB 2.0
to temperature.
the range of interrupting ratings vary from Supplemental Fuses. Cable Telephony X X
PBX/KTS And Key Telephone System X X USB Port USB Controller USB Port USB Controller
tens of amperes up to 10,000 amperes at
rated voltage. RESISTANCE: Reviewing product CPU X X V5.5MLA0603 V5.5MLA063
specifications indicates that similarly-rated USB X X X X X
VBU VBUS
IEEE1284 Parallel Data Bus X X X X 1206L150 1206L150
OPERATING VOLTAGE RATING: PTCs have about twice (sometimes more) D+ D+
Outside World
Outside World
Computer
IEEE 802.3 X X X D- D-
General use PTCs are not rated above 60V the resistance of fuses.
IEEE 1394 X X X
Log resistance (ohms)
Electronics
Consumer
Smart Card Reader X
Mobile Phone X X X
Temperature Derating Curves Comparing PTCs to Fuses
Understanding the differences in Linear AC/DC Adapter X X X X X X X
performance between the two types of Chart Key C Portable Electronic Input Port X X X X X
140
devices will make the best circuit protection Curve A Electromagnetic Loads, Motor X X X X IEEE 1394 – FireWire Tip/Ring circuit – Metallic
choice easier. The most obvious difference Solenoid Protection X X X X
Thin-Film Fuses and 313 120
Battery
Series (.010 to .150A) A Lithium Cell X X X X X
is that the PTC is resettable. This is an 1394 Port 1394 Controller RJ11 Connector Tx/Rx Circuits
PERCENT OF RATING
B X X X X X
inherent characteristic in which the PTC Curve B 100 Battery Pack V33MLA1206
resets (returns to low resistance state) B
FLAT-PAK®, Telelink®, VBU
electronic
1812L110/33
Medical
after power is removed and the device Nano2®, PICO®, 80 TPA+ Tip
Outside World
Blade Terminal, Voltage / Current Input Terminal X X TPA-
cools down. There are a number of other
Special Purpose and A TPB+
Telco
operating characteristics that differentiate 600R Series SMD/leaded
60 TPB-
other leaded and 250R Series SIDACtor®
the two types of products. cartridge fuses
NOTE: The application summary is for reference only. Determination of suitability for a specific application is the responsibility of the customer. Device
25°C
(except 313.010 – .150A) 40
C Ring
The terminology used for PTCs is often
(4) PGB1010603 Signal Signal
similar but not the same as for fuses. Two Curve C 20 Ground Ground
(PulseGuard®
parameters that fall into this category are Resettable PTCs ESD Suppressor)
-60°C -40°C -20°C 0°C 20°C 40°C 60°C 80°C 100°C 120°C
leakage current and fault current rating. -76°F -40°F -4°F 32°F 68°F 104°F 140°F 176°F 212°F 248°F Shield
Ground
AMBIENT TEMPERATURE
2 3 4
PTC Characteristics LEAKAGE CURRENT: A PTC is said to TEMPERATURE DERATING: The useful PTC Applications When to apply a resettable PTC vs. a Systems Interface) Standard for this large Littelfuse offers a full range of battery required. The following are typical examples complete protection for the circuit. Contact
have “tripped” when it has transitioned upper limit for a PTC is generally 85°C while traditional fuse is always the choice of the market includes a statement that “....a strap, surface mount and radial leaded of circuits using POLYFUSE® resettable your location Littelfuse application expert
and Terminology from its low resistance state to a high the maximum operating temperature for PTCs are used as circuit protection in designer or technician but in some cases, Positive Temperature Coefficient device resettable PTC devices designed to protect PTCs in combination with other Littelfuse for additional design assistance or
resistance state due to overload current. fuses is 125°C. The following temperature applications where sensitive components PTC’s offer a convenient form of circuit must be used instead of a fuse, to limit the applications where overcurrent protection is circuit protection devices to provide visit www.littelfuse.com/PTCs.
A polymeric PTC (positive temperature
derating curves (see chart at bottom of are at risk of damage from overcurrent protection to improve the reliability of an maximum amount of current sourced”.
coefficient) overcurrent protector is an Protection is accomplished by limiting the page) that compare PTCs to fuses illustrate conditions. The ability of PTCs to reset application. There is an important area of
element placed in series with the circuit or current flow to a low leakage level. Leakage The application selection guide below should
that more derating is required for a PTC at a themselves after exposure to a fault current applications where the use of resettable
assembly to be protected. The PTC current can range from less than a hundred be used as an aid in selecting the proper Power Over Ethernet Li-ion Battery Pack
given temperature. makes them ideal for use in circuits that are fuses (PTCs) has become a requirement.
element protects the circuit by changing milliamps at rated voltage up to a few device for your end application. Please
not easily accessible to a user or technician. Much of the design work for personal Swtich/Hub Powered End Station
from a low-resistance to a high resistance hundred milliamps at lower voltages. Additional operating characteristics can be consult the datasheets on www.littelfuse.com
Typical applications include port protection computers and peripheral devices is Battery Connector Battery Controller IC
state in response to an overcurrent. The fuse on the other hand completely reviewed by the circuit designer in making for detailed technical specifications.
on personal computers (USB, Firewire, strongly influenced by the Microsoft and
This function is called “tripping” of the interrupts the current flow and this open the decision to choose a PTC or a fuse for keyboard/mouse, and serial ports), Intel System Design Guide which states
Data Pair Data Pair
Battery +
overcurrent protection device. circuit results in no leakage current after it overcurrent protection. peripherals (hard drives, video cards, and that “Using a fuse that must be replaced Battery -
Cell Phone
has been subjected to an overload current. hubs), cell phone, battery packs, industrial each time an overcurrent condition occurs is Control
Overcurrent circuit protection can be AGENCY APPROVALS: PTCs are
controls, lighting ballast and motor controls. unacceptable.” And the SCSI (Small Computer Power Source Powered
accomplished with the use of either a FAULT CURRENT: The PTC is rated for Recognized under the Component
Equipment Device
traditional fuse or the more recently a maximum short circuit current at rated Program of Underwriters Laboratories to (PSE) (PD) (3) V5.5MLA0402
voltage. This fault current level is the UL Standard 1434 for Thermistors. SURFACE MOUNT RADIAL LEADED BATTERY STRAP (AXIAL LEADED) (Multilayer
developed resettable PTC. Both devices Varistor)
maximum current that the device can safely The devices have also been approved for Series Name 0805L 1206L 1210L 1812L 2016L 2920L USBR 30R 60R 250R 600R ST LT LR VT VL Signal
function by reacting to the heat generated Application
Ground
by the excessive current flow in the circuit. limit keeping in mind that the PTC will not use in Canada by Underwriters Laboratories.
Ul60950 ,TIA-968-A, GR-1089 Requirements X X Data Pair Data Pair
The fuse element melts open, interrupting actually interrupt the current flow (see Approvals for fuses include Recognition Shield
ITU-T Recoomendations X X Ground
the current flow, while the PTC changes LEAKAGE CURRENT above). The typical under the Component Program of CPE (Customer Premises Equipment) X X
Telecom
from low resistance to high resistance short circuit rating of a board-mounted PTC Underwriters Laboratories and the CSA Analog Line Card X X
to limit current flow. The graph below is 40A; for battery strap PTCs, this value can Component Acceptance Program. In addition, T1/E1/J1 And HDSL X X
shows the response of the PTC device reach 100A. Fuses do in fact interrupt the many fuses are listed in accordance with ISDN X X
current flow in response to the overload and UL/CSA/ANCE (Mexico) 248-14, ADSL X X USB 1.1 USB 2.0
to temperature.
the range of interrupting ratings vary from Supplemental Fuses. Cable Telephony X X
PBX/KTS And Key Telephone System X X USB Port USB Controller USB Port USB Controller
tens of amperes up to 10,000 amperes at
rated voltage. RESISTANCE: Reviewing product CPU X X V5.5MLA0603 V5.5MLA063
specifications indicates that similarly-rated USB X X X X X
VBU VBUS
IEEE1284 Parallel Data Bus X X X X 1206L150 1206L150
OPERATING VOLTAGE RATING: PTCs have about twice (sometimes more) D+ D+
Outside World
Outside World
Computer
IEEE 802.3 X X X D- D-
General use PTCs are not rated above 60V the resistance of fuses.
IEEE 1394 X X X
Log resistance (ohms)
Electronics
Consumer
Smart Card Reader X
Mobile Phone X X X
Temperature Derating Curves Comparing PTCs to Fuses
Understanding the differences in Linear AC/DC Adapter X X X X X X X
performance between the two types of Chart Key C Portable Electronic Input Port X X X X X
140
devices will make the best circuit protection Curve A Electromagnetic Loads, Motor X X X X IEEE 1394 – FireWire Tip/Ring circuit – Metallic
choice easier. The most obvious difference Solenoid Protection X X X X
Thin-Film Fuses and 313 120
Battery
Series (.010 to .150A) A Lithium Cell X X X X X
is that the PTC is resettable. This is an 1394 Port 1394 Controller RJ11 Connector Tx/Rx Circuits
PERCENT OF RATING
B X X X X X
inherent characteristic in which the PTC Curve B 100 Battery Pack V33MLA1206
resets (returns to low resistance state) B
FLAT-PAK®, Telelink®, VBU
electronic
1812L110/33
Medical
after power is removed and the device Nano2®, PICO®, 80 TPA+ Tip
Outside World
Blade Terminal, Voltage / Current Input Terminal X X TPA-
cools down. There are a number of other
Special Purpose and A TPB+
Telco
operating characteristics that differentiate 600R Series SMD/leaded
60 TPB-
other leaded and 250R Series SIDACtor®
the two types of products. cartridge fuses
NOTE: The application summary is for reference only. Determination of suitability for a specific application is the responsibility of the customer. Device
25°C
(except 313.010 – .150A) 40
C Ring
The terminology used for PTCs is often
(4) PGB1010603 Signal Signal
similar but not the same as for fuses. Two Curve C 20 Ground Ground
(PulseGuard®
parameters that fall into this category are Resettable PTCs ESD Suppressor)
-60°C -40°C -20°C 0°C 20°C 40°C 60°C 80°C 100°C 120°C
leakage current and fault current rating. -76°F -40°F -4°F 32°F 68°F 104°F 140°F 176°F 212°F 248°F Shield
Ground
AMBIENT TEMPERATURE
2 3 4
Selection Process that the circuit parameters do not exceed 5. Check that the trip time protects
these ratings. the circuit.
1. Determine the following circuit operating
parameters: 4. Verify that the ambient operating 6. Verify that the post trip resistance (R1MAX)
• Normal operating current – IHOLD
temperature within close proximity to of the device is taken into account in the
• Maximum circuit voltage – VMAX the device is within its normal operating circuit design.
• Maximum interrupt current – IMAX range. Thermally derate IHOLD and IMAX as 7. Independently test and evaluate the
POLYFUSE® PTC SELECTION GUIDE
• Ambient operating temperature
necessary. See equation below. suitability and performance of the PTC
2. Select the suitable form factor.
in the actual application.
3. Compare the PTC data sheet ratings on IMAX World Headquarters
IHOLD =
littelfuse.com for VMAX and IMAX to ensure Thermal derating factor Littelfuse, Inc.
800 E. Northwest Highway
Des Plaines, IL 60016 USA
PTC Selection Table www.littelfuse.com
SURFACE MOUNT RADIAL LEADED
Series Name 0805L 1206L 1210L 1812L 2016L 2920L USBR 30R
Max voltage 60V 60/250V 60/600V 15-30V 15-24V 15-20V 16V NA Specifications, descriptions and illustrative material in this literature are as accurate as known at the time of
publication, but are subject to change without notice.
NA = Not Available
5