Professional Documents
Culture Documents
AT&T - Ericsson-UTRAN-Field-Guide-Notification-Alert-Layer-Management-Configuration PDF
AT&T - Ericsson-UTRAN-Field-Guide-Notification-Alert-Layer-Management-Configuration PDF
A Field Guide Alert is sent as part of the normal Field Guide Alert process to communicate a chance in the
National recommendation for Ericsson UTRAN configurable parameters. This Field Guide Alert focuses
on achieving our Layer Management Guiding Principals. The following two Guiding Principals are
addressed.
The first objective, to keep the UE on the 3G network within the UMTS polygon, is mainly achieved
through specifically designated Cell Selection and Cell Reselection parameters. Once the UEs are
allowed to camp on the 3G network, the second objective is addressed as Inter-RAT and Inter-Frequency
handovers are reduced or virtually eliminated through specifically designated Event 2d parameters.
Inter-RAT and Inter-Frequency Cell Reselection and Handover are supported at their respective boarders
at RSCP and Ec/No levels that allow a high probability for successful Compressed Mode operation.
This Field Guide Alert is a reissue of Field Guide Alert 4.0-E-010 released on 5/1/2009. The following is a
list of parameter value deltas between the previous release and this release.
In addition to these parameter changes, a number of Inter-Site inter-RAT and Inter-Frequency neighbor
relations are being removed. Details follow:
‘sho_c’ designated cells:
Given UEs that are served by ‘sho_c’ designated cells do not need to perform hard Inter-RAT or Inter-
Frequency handover in order to maintain calls, Compressed Mode operation is inhibited by moving the
point at which Event 2d it sent to a point below which the UEs camp. This virtually eliminates Event 2d
triggers on ‘sho_c’ designated cells. These cells will exist mainly in the core, but will also exist where the
2G and 3G networks share the same geographic border (system coverage edge).
For the quality (Ec/No) based algorithms, this is accomplished by setting usedFreqThresh2dEcno(sho_c)
[Cell, -23, dB, Fixed] – hysteresis2d [RNC, 4, 0.5 dB, Fixed] / 2 to an effective value of -24dB which will
cause UEs send Event 2d when they see an Ec/No worse than -24dB for timeToTrigger2dEcno [RNC,
320, ms, Fixed]. For camping, qQualMin(sho_c) [Cell, -24, dB, Fixed] + sRatSearch(sho_c) [Cell, 0, dB,
Fixed] is set to an effective value of -20dB Ec/No which will cause the UE to perform Inter-RAT
measurements for Cell Reselection at or worse than -20dB Ec/No.
sIntraSearch(sho_c) [Cell, 25=16, dB, Fixed] is set to an effective value of -8dB Ec/No which will cause
the UE to search for a better Intra-Frequency neighbor at or worse than -8dB Ec/No. The average Ec/No
value for UEs doing Speech varies between -7dB and -10dB depending upon market.
For the level (RSCP) based triggers, usedFreqThresh2dRscp(sho_c) [Cell, -115, dBm, Fixed] –
hysteresis2d [RNC, 4, 0.5 dB, Fixed] / 2 is set to an effective value of -116dBm which will cause UEs
send Event 2d when they see an RSCP worse than -116dBm for timeToTrigger2dRscp [RNC, 320, ms,
Fixed]. For camping, qRxLevMin(sho_c) [Cell, -115, odd dBm, Fixed] + sHcsRat [Cell, -105, dB, Fixed]
is set to cause the UE to consider the cell to be non-suitable at or worse than an RCSP of -115dBm.
Negative values for sHcsRat [Cell, -105, dB, Fixed] are considered = 0. A positive value will be
considered when there are enough CR-130 capable UEs in production to warrant a Field Study.
Consequently, UEs will not camp at values of Ec/No or RSCP that would allow Event 2d to be sent if they
were to establish a call.
hoType(sho_c) [Cell, 2=NONE, String, Fixed] is set to NONE in order to preclude the use of Compressed
Mode for sho_c designated cells. By setting the Event 2d, Cell Selection and Reselection parameters
accordingly, Compressed Mode operation for Speech should be eliminated (except for UEs on a Drift
RNC) and HSPA down-switch to DCH/DCH should be reduced.
Neighbor list: Given ‘sho_c’ designated cells do not support Inter-RAT or Inter-Frequency handover,
Inter-Site Inter-RAT and Inter-Frequency neighbor relations are not needed and should be removed.
Intra-Site Inter-RAT neighbor relations should be maintained in order to support population of the UE’s
ARFCN hotlist for e911 redirection to 2G, and Intra-Site Inter-Frequency neighbor relation should be
maintained in order to support Inter-Frequency Load Sharing (IFLS).
For the level based algorithms, usedFreqThresh2dRscp(hho_if_c) [Cell, -115, dBm, Fixed] –
hysteresis2d [RNC, 4, 0.5 dB, Fixed] / 2 is set to an effective value of -116dBm which will cause UEs
send Event 2d when they see an RSCP worse than -116dBm for timeToTrigger2dRscp [RNC, 320, ms,
Fixed]. For camping, qRxLevMin(hho_if_c) [Cell, -115, odd dBm, Fixed] is set to cause the UE to
consider the cell non-suitable at or worse than an RCSP of -115dBm.
Neighbor list: Given ‘hho_if_c’ designated cells do not support Inter-RAT handover, Inter-Site Inter-RAT
neighbor relations are not needed and should be removed. Intra-Site Inter-RAT neighbor relations should
be maintained in order to support population of the UE’s ARFCH hotlist for e911 redirection to 2G, and
Intra-Site Inter-Frequency neighbor relation should be maintained in order to support Inter-Frequency
Load Sharing (IFLS).
For the level based algorithms, usedFreqThresh2dRscp(hho_if_b) [Cell, -106 ±4, dBm, Fixed] –
hysteresis2d [RNC, 4, 0.5 dB, Fixed] / 2 is set to an effective value of -107 ±4 which will cause UEs send
Event 2d when they see an RSCP worse than -107 ±4 for timeToTrigger2dRscp [RNC, 320, ms, Fixed].
For camping, qRxLevMin(hho_if_b) [Cell, -107 ±4, odd dBm, Fixed] is set to cause the UE to consider the
cell non-suitable at an RCSP at or worse than -107 ±4 dBm. Be sure to maintain the Camping / Event 2d
trigger point relationship between the parameter values when using values inside the given tolerance.
Neighbor list: Given ‘hho_if_b’ designated cells do not support Inter-RAT handover, Inter-Site Inter-RAT
neighbor relations are not needed and should be removed. Intra-Site Inter-RAT neighbor relations should
be maintained in order to support population of the UE’s ARFCH hotlist for e911 redirection to 2G, and
Intra-Site Inter-Frequency neighbor relation should be maintained in order to support Inter-Frequency
Load Sharing (IFLS).
For the level based algorithms, usedFreqThresh2dRscp(hho_ir_c) [Cell, -115, dBm, Fixed] –
hysteresis2d [RNC, 4, 0.5 dB, Fixed] / 2 is set to an effective value of -116 which will cause UEs send
Event 2d when they see an RSCP worse than -116 for timeToTrigger2dRscp [RNC, 320, ms, Fixed].
For camping, qRxLevMin(hho_ir_c) [Cell, -115, odd dBm, Fixed] is set to cause the UE to consider the
cell to be non-suitable at an RCSP at or worse than -115dBm.
This combination of settings disables RSCP based Event 2d triggers for Inter-RAT in the core.
Neighbor list: Given ‘hho_ir_c’ designated cells do not support Inter-Frequency handover, Inter-Site
Inter-Frequency neighbor relations are not needed and should be removed. Intra-Site Inter-RAT neighbor
relations should be maintained in order to support population of the UE’s ARFCH hotlist for e911
redirection to 2G, and Intra-Site Inter-Frequency neighbor relation should be maintained in order to
support Inter-Frequency Load Sharing (IFLS).
For the level based algorithms, usedFreqThresh2dRscp(hho_ir_b) [Cell, -106 ±4, dBm, Fixed] –
hysteresis2d [RNC, 4, 0.5 dB, Fixed] / 2 is set to an effective value of -107 ±4 which will cause UEs send
Event 2d when they see an RSCP worse than -107 ±4 dBm for timeToTrigger2dRscp [RNC, 320, ms,
Fixed]. For camping, qRxLevMin(hho_ir_b) [Cell, -109 ±2, odd dBm, Fixed] is set to cause the UE to
consider the cell non-suitable at an RCSP at or worse than -109 ±2 dBm. Be sure to maintain the
Camping / Event 2d trigger point relationship between the parameter values when using values inside the
given tolerance.
Neighbor list: Given ‘hho_ir_b’ designated cells do not support Inter-Frequency handover, Inter-Site
Inter-Frequency neighbor relations are not needed and should be removed. Intra-Site Inter-RAT neighbor
relations should be maintained in order to support population of the UE’s ARFCH hotlist for e911
redirection to 2G, and Intra-Site Inter-Frequency neighbor relation should be maintained in order to
support Inter-Frequency Load Sharing (IFLS).
Caution:
Changing these parameters, especially the “S” parameters (qQualMin and qRxLevMin), will likely cause a
large number of UEs to move to the 3G network. The amount of impact is dependant upon your previous
configuration. It’s important to monitor changes in consumable resource utilization and blocking after
implementation of this Field Guide Alert. As well, the following metrics should be observed.
Note: The parameter values indicated in the Ericsson UMTS Gold Standard located at the Gold
Standards Governance Team website supersede any parameter values recommended by any Field Guide
Alert or other document that provide recommendations for parameter values. Please consult the Ericsson
UMTS Gold Standard when in doubt.
Ericsson sho_c hho_if_c hho_if_b hho_ir_c hho_ir_b
UTRAN
CM Start usedFreqThresh2dEcno(sho_c) usedFreqThresh2dEcno(hho_if_c) usedFreqThresh2dEcno(hho_if_b) usedFreqThresh2dEcno(hho_ir_c) usedFreqThresh2dEcno(hho_ir_b)
(2d) [Cell, -23, dB, Global] [Cell, -15, dB, Local] [Cell, -15, dB, Local] [Cell, -15, dB, Local] [Cell, -15, dB, Local]
Quality timeToTrigger2dEcno [RNC, 320, ms, timeToTrigger2dEcno [RNC, 320, ms, timeToTrigger2dEcno [RNC, 320, ms, timeToTrigger2dEcno [RNC, 320, ms, timeToTrigger2dEcno [RNC, 320, ms,
Global] Global] Global] Global] Global]
CM Start usedFreqThresh2dRscp(sho_c) usedFreqThresh2dRscp(hho_if_c) usedFreqThresh2dRscp(hho_if_b) usedFreqThresh2dRscp(hho_ir_c) usedFreqThresh2dRscp(hho_ir_b)
(2d) [Cell, -115, dBm, Global] [Cell, -115, dBm, Local] [Cell, -106±4dB, dBm, Local] [Cell, -115, dBm, Local] [Cell, -109±2dB, dBm, Local]
Level timeToTrigger2dRscp [RNC, 320, ms, timeToTrigger2dRscp [RNC, 320, ms, timeToTrigger2dRscp [RNC, 320, ms, timeToTrigger2dRscp [RNC, 320, ms, timeToTrigger2dRscp [RNC, 320, ms,
Global] Global] Global] Global] Global]
CM (2d) hysteresis2d [RNC, 4, 0.5 dB, Global] hysteresis2d [RNC, 4, 0.5 dB, Global] hysteresis2d [RNC, 4, 0.5 dB, Global] hysteresis2d [RNC, 4, 0.5 dB, Global] hysteresis2d [RNC, 4, 0.5 dB, Global]
Quality / hoType(sho_c) hoType(hho_if_c) hoType(hho_if_b) hoType(hho_ir_c) hoType(hho_ir_b)
Level [Cell, 2=NONE, String, Global] [Cell, 0=IFHO_PREFERRED, String, [Cell, 0=IFHO_PREFERRED, String, [Cell, 1=GSM_PREFERRED, String, [Cell, 1=GSM_PREFERRED, String,
Global] Global] Global] Global]
CM Stop (2f) usedFreqRelThresh2fEcno(sho_c) usedFreqRelThresh2fEcno(hho_if_c) usedFreqRelThresh2fEcno(hho_if_b) usedFreqRelThresh2fEcno(hho_ir_c) usedFreqRelThresh2fEcno(hho_ir_b)
Quality [Cell, 2, dB, Global] [Cell, 2, dB, Global] [Cell, 2, dB, Global] [Cell, 2, dB, Global] [Cell, 2, dB, Global]
CM Stop (2f) usedFreqRelThresh2fRscp(sho_c) usedFreqRelThresh2fRscp(hho_if_c) usedFreqRelThresh2fRscp(hho_if_b) usedFreqRelThresh2fRscp(hho_ir_c) usedFreqRelThresh2fRscp(hho_ir_b)
Level [Cell, 6, dB, Global] [Cell, 6, dB, Global] [Cell, 6, dB, Global] [Cell, 6, dB, Global] [Cell, 6, dB, Global]
CM Stop (2f) timeToTrigger2f [RNC, 640, ms, Global] timeToTrigger2f [RNC, 640, ms, Global] timeToTrigger2f [RNC, 640, ms, Global] timeToTrigger2f [RNC, 640, ms, Global] timeToTrigger2f [RNC, 640, ms, Global]
Quality / hysteresis2f [RNC, 2, 0.5 dB, Global] hysteresis2f [RNC, 2, 0.5 dB, Global] hysteresis2f [RNC, 2, 0.5 dB, Global] hysteresis2f [RNC, 2, 0.5 dB, Global] hysteresis2f [RNC, 2, 0.5 dB, Global]
Level
Event 3a utranRelThresh3aRscp [RNC, 7, dB, utranRelThresh3aRscp [RNC, 7, dB, utranRelThresh3aRscp [RNC, 7, dB, utranRelThresh3aRscp [RNC, 7, dB, utranRelThresh3aRscp [RNC, 7, dB,
Level Global] Global] Global] Global] Global]
Event 3a utranRelThresh3aEcno [RNC, 2, dB, utranRelThresh3aEcno [RNC, 2, dB, utranRelThresh3aEcno [RNC, 2, dB, utranRelThresh3aEcno [RNC, 2, dB, utranRelThresh3aEcno [RNC, 2, dB,
Quality Global] Global] Global] Global] Global]
GSM timeToTrigger3a [RNC, 6=100, ms, Local] timeToTrigger3a [RNC, 6=100, ms, timeToTrigger3a [RNC, 6=100, ms, Local] timeToTrigger3a [RNC, 6=100, ms, timeToTrigger3a [RNC, 6=100, ms,
Handover Local] Local] Local]
(3a) gsmThresh3a [RNC, -98, dBm, Global] gsmThresh3a [RNC, -98, dBm, Global] gsmThresh3a [RNC, -98, dBm, Global] gsmThresh3a [RNC, -98, dBm, Global] gsmThresh3a [RNC, -98, dBm, Global]
Quality/Level
hysteresis3a [RNC, 4, 0.5dB, Local] hysteresis3a [RNC, 4, 0.5dB, Local] hysteresis3a [RNC, 4, 0.5dB, Local] hysteresis3a [RNC, 4, 0.5dB, Local] hysteresis3a [RNC, 4, 0.5dB, Local]
Cell qQualMin(sho_c) [Cell, -24, dB, Global] qQualMin(hho_if_c) [Cell, -24, dB, qQualMin(hho_if_b) [Cell, -24, dB, Global] qQualMin(hho_ir_c) [Cell, -20, dB, qQualMin(hho_ir_b) [Cell, -20, dB,
Selection / Global] Global] Global]
Reselection sRatSearch(sho_c) [Cell, 0, dB, Global] sRatSearch(hho_if_c) [Cell, 0, dB, sRatSearch(hho_if_b) [Cell, 0, dB, Global] sRatSearch(hho_ir_c) [Cell, 4, dB, sRatSearch(hho_ir_b) [Cell, 4, dB,
Quality Global] Global] Global]
sIntraSearch(sho_c) [Cell, 16, dB, Global] sIntraSearch(hho_if_c) [Cell, 16, dB, sIntraSearch(hho_if_b) [Cell, 16, dB, sIntraSearch(hho_ir_c) [Cell, 12, dB, sIntraSearch(hho_ir_b) [Cell, 12, dB,
Global] Global] Global] Global]
sInterSearch(sho_c) [Cell, 16, dB, Global] sInterSearch(hho_if_c) [Cell, 16 dB, sInterSearch(hho_if_b) [Cell, 16 dB, sInterSearch(hho_ir_c) [Cell, 12, dB, sInterSearch(hho_ir_b) [Cell, 12, dB,
Global] Global] Global] Global]
FDDQMIN(sho_c)=-20dB FDDQMIN(hho_if_c)=-20dB FDDQMIN(hho_if_b)=-20dB FDDQMIN(hho_ir_c)=-12dB FDDQMIN(hho_ir_b)=-12dB
qHyst2 [Cell, 4, dB, Global] qHyst2 [Cell, 4, dB, Global] qHyst2 [Cell, 4, dB, Global] qHyst2 [Cell, 4, dB, Global] qHyst2 [Cell, 4, dB, Global]
qOffset1sn [Nabr, 7, dB, Global] qOffset1sn [Nabr, 7, dB, Global] qOffset1sn [Nabr, 7, dB, Global] qOffset1sn [Nabr, 7, dB, Global] qOffset1sn [Nabr, 7, dB, Global]
qOffset2sn [Nabr, -10..10, dB, Local] qOffset2sn [Nabr, -10..10, dB, Local] qOffset2sn [Nabr, -10..10, dB, Local] qOffset2sn [Nabr, -10..10, dB, Local] qOffset2sn [Nabr, -10..10, dB, Local]
Cell qRxLevMin(sho_c) [Cell, -115, odd dBm, qRxLevMin(hho_if_c) [Cell, -115, odd qRxLevMin(hho_if_b) [Cell, -107±4dB, qRxLevMin(hho_ir_c) [Cell, -115, odd qRxLevMin(hho_ir_b) [Cell, -109±2dB,
Selection / Global] dBm, Global] odd dBm, Global] dBm, Global] odd dBm, Global]
Reselection sHcsRat [Cell, -105, dB, Global] sHcsRat [Cell, -105, dB, Global] sHcsRat [Cell, -105, dB, Global] sHcsRat [Cell, -105, dB, Global] sHcsRat [Cell, -105, dB, Global]
Level
fddrscpmin: [Cell, -114, dB, Global] fddrscpmin: [Cell, -114, dB, Global] fddrscpmin: [Cell, -114, dB, Global] fddrscpmin: [Cell, -114, dB, Global] fddrscpmin: [Cell, -114, dB, Global]
Cell tReselection [Cell, 2, seconds, Global] tReselection [Cell, 2, seconds, Global] tReselection [Cell, 2, seconds, Global] tReselection [Cell, 2, seconds, Global] tReselection [Cell, 2, seconds, Global]
Reselection
Quality/Level
IR Neighbor Intra Site only. Intra Site only. Intra Site only. Intra and Inter Site. Intra and Inter Site.
List
IF Neighbor Intra Site only Intra and Inter Site Intra and Inter Site Intra Site only. Intra Site only.
List
Implementation of the Change:
In the space below, describe in detail how this change is implemented for each system impacted.
This Field Guide Alert applies to multiple parameters. Due to the nature of the algorithms these
parameters influence, all parameters should be changed together within a single maintenance window for
each market.
Important note: Given these parameter changes are made based upon Cell Designation, it is vital that all
cells are properly designated and that the Cell Designation information is accurate in the Prospect
database.
Following a Controlled Introduction of this FGA (dates will be announced), and after verifying each cell’s
designation and updating the database, each market should open an IWOS ticket to have the MPC
implement this Field Guide Alert. An IWOS Job Aid is available to assist you in obtaining credentials (if
necessary) and submitting the IWOS ticket. The CIQ/MRDT Request form referenced in the Job Aid will
be made available.
IPMO will assist in coordinating implementation based upon the reception of IWOS tickets.
Implementation should be complete by July 31st 2010.