Professional Documents
Culture Documents
Detan Rod Systems: HSC Ec 11-Usa DT 14-US
Detan Rod Systems: HSC Ec 11-Usa DT 14-US
FAÇADE
HALFEN DETAN Rod Systems.
The most Trusted Name. The most Elegant Application.
Project:
Manchester Civil
Justice Centre, UK
Project:
Yale University Cancer
Hospital, CT, US
Corrosion protection
Reliable and durable
Carbon steel DETAN Rod Systems offer
high quality finishes and seals to protect • Tension rods are completely hot-dip
against corrosion. galvanized after the manufacturing
process to provide the best protection
with no danger of hydrogen
embrittlement
• Rods have a clean and even, flat
finish with no runs or flaking zinc
hot-dip galvanized • Neat milled wrench flats are provided
(brushed)
for reliable rod tightening and simple
length adjustment
• Forks and locking nuts are hot dip
galvanized
Threaded plug
• Internal threads are also coated
Seals hot-dip galvanized
(standard) • Seals are provided as a standard for
Internal thread
coated
rods 16 mm (5/8”) diameter and
higher to protect threads from
humidity and contamination
Plug Seal set (fv,wb) All fork ends are delivered with a plug areas of the system. We recommend
Flat seal Round seal installed to the open end of the thread that a permanent elastic silicone
for the rod connection. The plugs are (designed for external use) is applied to
color-coded according to the thread the outer edge of the locking nut. This
direction. Yellow = right-hand thread. process should be applied to locking
Blue = left-hand thread. nuts located at fork ends and couplers.
Fork end Locking nut Tension rod It is recommended that both the inner
Carbon steel DETAN system diameters and the outer edges of the locking nut
in the range M16 (5/8”) – M95 (3 ¾”) are sealed with silicone for system
are provided with special seals to provi- diameters < M16 (5/8”).
de corrosion protection to the threaded
Component identification
Basic system:
E W ! ilable: tem
N a ys
av el S
w
no ss Ste DETAN Tension Rods are
inle recommended only for
Sta
Load capacity, predominantly static loads.
system dimensions
and materials
DETAN Tension Rod → pp. 12 - 14
System variants:
Suspension consists
of a system variant
with coupler with lug
with couplers or with couplers with lug and one basic system Dimensions and materials → pp. 13 - 15
W ! ilable:
NE
m
ste
ava el Sy
w
no ss Ste
inle Cross bracing
Sta
consists of one
system variant with
cross coupler and
with cross coupler for cross bracing one basic system
Dimensions and materials → p.13
Cross bracing:
Cross bracing
consists of one
anchor disc and up
Anchor disc for cross bracing to 8 basic systems Dimensions and materials → pp. 13 - 15
Load capacity,
system dimensions Further
and materials information
DETAN Compression Rod → p. 16 → pp. 17 - 18
Basic System
System diameter ds
System length L
System Variants
Using couplers:
System diameter ds
System length L
If the basic system length is greater than the maximum span possible with a single rod, then couplers are added.
System diameter ds
System length L
Couplers with support lugs enable long spans of joined DETAN rods to be supported from above using vertical lengths of DETAN
rods connected to the structure. This method is used to reduce deflection across long system lengths.
Note: Maximum 5 couplers possible.
Delivery in single components.
System Variants
System length L
DETAN rods can pass through cross couplers to enable cross bracing in the same plane.
Normally DETAN systems are simply ordered by specifying the desired system diameter ds and the system length L. HALFEN
calculates the rod lengths and checks the minimum and/or maximum system lengths. Couplers are automatically distributed
symmetrically.
If an asymmetric distribution of the couplers is required, a dimensioned drawing must be included with the purchase order. A typical
example of the dimensions required is illustrated in the drawing below.
A drawing with system dimensions is sufficient.
HALFEN will detail complex rod systems as one
configured system.
ds = 3/8"
L = 42"
ds = 15/16"
Ordering example:
Tension Rod System, DETAN-S460, ds = 15/16", system length according to drawing, wb, couplers according to drawing
Tension Rod System, DETAN-S460, ds = 3/8", system length L = 42" wb
Cross Bracing
β
Anchor Disc:
Note:
α • max. 8 tension rod connections
α
possible
• Connecting angle α min = 40°
DETAN Anchor Discs provide an architectural center connection for DETAN rods when they are used for cross bracing.
Please specify material, finish, system diameter ds, number of holes, and connecting angle α when ordering.
Height H [mm]
s
s
.d
.d
am
am
di
m
ste
Sy
Sy
• Fork connection set: Fork, locking nuts, pins, • Locking nut, left-hand thread
snap rings, seal kit , left-hand thread • Locking nut, right-hand thread
• Coupler set:
• Snap ring for one fork
coupler + 2 locking nuts, seal kit
Use of DETAN components with products from other manufacturers invalidates performance data and any warranties. not available with stainless steel
Tension Rods
System length L
Screw-in [mm] 15.0 18.5 22.5 27.0 34.0 37.5 42.5 51.0 55.0 62.5 70.5 77.5 85.0 115 130 155
depth om
[inches] 9/16 3/4 7/8 1 1/16 1 5/16 1 1/2 1 11/16 2 2 3/16 2 7/16 2 3/4 3 1/16 3 3/8 4 1/2 5 1/8 6 1/8
Length [mm] 5.0 6.5 7.5 8.0 11.0 12.5 12.5 14.0 15.0 17.5 20.0 22.5 25.0 39 45 60
adjustment oj
[inches] 3/16 1/4 5/16 5/16 7/16 1/2 1/2 9/16 9/16 11/16 13/16 7/8 1 1 9/16 1 3/4 2 3/8
Locking nut [mm] 24.5 37.0 41.0 50.0 58.0 63.0 64.0 72.0 83.0 91.0 98.0 105.0 112.0 148.0 165.0 205.0
M
length [inches] 15/16 1 7/16 1 5/8 1 15/16 2 5/16 2 1/2 2 1/2 2 13/16 3 1/4 3 9/16 3 7/8 4 1/8 4 7/16 5 13/16 6 1/2 8 1/16
Couplers
dsa
Regular couplers Couplers Cross
α min
with lugs couplers
=60
L KM
d KM
om
°-90
LM
°
+oj -oj
ds
ds
ds
kM
kM
dsk
dM
connecting angle
ds
LM LM α = 60°-90°
Dimensions
System diameter [mm] 10 12 16 20 24 27 30 36 42 48 52 56 60 76 85 95
ds /dsk [inches] 3/8 1/2 5/8 13/16 15/16 1 1/16 1 3/16 1 7/16 1 5/8 1 7/8 2 1/16 2 3/16 2 3/8 3 3 3/8 3 3/4
Coupler [mm] 40 50 62 78 94 104 120 140 158 180 195 210 245 328 370 450
length LM
[inches] 1 9/16 1 15/16 2 7/16 3 1/16 3 11/16 4 1/8 4 3/4 5 1/2 6 1/4 7 1/16 7 11/16 8 1/4 9 5/8 12 15/16 14 9/16 17 11/16
Coupler [mm] 20 22 28 35 42 47 53 64 75 87 93 98 104 155 180 195
diameter dM
[inches] 13/16 7/8 1 1/8 1 3/8 1 5/8 1 7/8 2 1/16 2 1/2 2 15/16 3 7/16 3 11/16 3 7/8 4 1/8 6 1/8 7 1/16 7 11/16
Screw-in [mm] 15.0 18.5 22.5 27.0 34.0 37.5 42.5 51.0 55.0 62.5 70.5 77.5 85.0 115 130 155
depth om
[inches] 9/16 3/4 7/8 1 1/16 1 5/16 1 1/2 1 11/16 2 2 3/16 2 7/16 2 3/4 3 1/16 3 3/8 4 1/2 5 1/8 6 1/8
Length [mm] 5.0 6.5 7.5 8.0 11.0 12.5 12.5 14.0 15.0 17.5 20.0 22.5 25.0 39 45 60
adjustment oj
[inches] 3/16 1/4 5/16 5/16 7/16 1/2 1/2 9/16 9/16 11/16 13/16 7/8 1 1 9/16 1 3/4 2 3/8
Support system [mm] – 10 10 10 10 10 10 10 10 12 12 12 12 12 16 16
diam. dsa
[inches] - 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 1/2 1/2 1/2 1/2 1/2 5/8 5/8
[mm] – 28.0 31.0 44.5 48.0 50.5 57.5 72.0 86.5 98.5 111.5 124.5 137.0 140.0 150.0 157.5
Lug offset km
[inches] - 1 1/8 1 1/4 1 3/4 1 7/8 2 2 1/4 2 13/16 3 3/8 3 7/8 4 3/8 4 7/8 5 3/8 5 1/2 5 7/8 6 3/16
Cross coupler [mm] 142 166 200 222 242 284
Lkm
length [inches] 5 9/16 6 9/16 7 7/8 8 3/4 9 1/2 11 3/16
Cross coupler [mm] 32 39 46 52 57 70
dkm
diam. [inches] 1 1/4 1 9/16 1 13/16 2 1/16 2 1/4 2 3/4
Peg wrench size [mm] - - - - - - - - - - - - - 155/8 230/10 230/10
Øg
Øf
α min 40°
≈. 2.5 r
b
approx. 4.2 r
Note: A can only be used when simultaneously using the circular anchor disc at 45°, see page 7!
Dimensions
System diameter [mm] 10 12 16 20 24 27 30 36 42 48 52 56 60 76 85 95
ds /dsk [inches] 3/8 1/2 5/8 13/16 15/16 1 1/16 1 3/16 1 7/16 1 5/8 1 7/8 2 1/16 2 3/16 2 3/8 3 3 3/8 3 3/4
Connection [mm] 90 110 140 180 210 240 260 310 360 420 450 490 520 702 777 832
Øf
diameter [inches] 3 9/16 4 5/16 5 1/2 7 1/16 8 1/4 9 7/16 10 1/4 12 3/16 14 3/16 16 9/16 1711/16 19 5/16 20 1/2 27 5/8 30 9/16 32 3/4
Disc [mm] 120 146 186 238 280 318 346 412 480 558 600 652 692 960 1075 1150
Øg
diameter [inches] 4 3/4 5 3/4 7 5/16 9 3/8 11 12 1/2 13 5/8 16 1/4 18 7/8 21 15/16 23 5/8 25 11/16 27 1/4 37 13/16 42 5/16 45 1/4
Plate [mm] 8 10 15 18 20 22 25 30 35 40 45 50 55 65 75 85
b
thickness [inches] 5/16 3/8 9/16 5/8 3/4 7/8 1 1 1/8 1 3/8 1 1/2 1 3/4 1 3/4 2 2 1/2 3 3 1/4
Pin hole [mm] 9.5 11.5 15.5 19.5 23.5 26.5 29.5 33.5 41 47 49 53 57 76 86 96
Øj
diameter [inches] 3/8 15/32 5/8 25/32 15/16 1 1/16 1 5/32 1 5/16 1 19/32 1 27/32 1 29/32 2 3/32 2 1/4 3 3 3/8 3 3/4
Pin hole [mm] 15 18 24 29 35 39 43 51 60 70 76 83 88 129 149 159
r
position [inches] 9/16 11/16 15/16 1 1/8 1 3/8 1 9/16 1 11/16 2 2 3/8 2 3/4 3 3 1/4 3 7/16 5 1/16 5 7/8 6 1/4
Min. plate [mm] 28 33 40 51 64 73 80 94 113 129 142 151 161 216 240 270
s
width [inches] 1 1/8 1 5/16 1 9/16 2 2 1/2 2 7/8 3 1/8 3 11/16 4 7/16 5 1/16 5 9/16 5 15/16 6 5/16 8 1/2 9 7/16 10 5/8
Tension Rods
System length L
Screw-in [mm] 10.5 12.5 15.0 18.5 22.5 27.0 34.0 37.5 42.5
depth om
[inches] 7/16 1/2 9/16 3/4 7/8 1 1/16 1 5/16 1 1/2 1 11/16
Length adjust- [mm] 4.5 4.5 5.0 6.5 7.5 8.0 11.0 12.5 12.5
ment oj
[inches] 3/16 3/16 3/16 1/4 5/16 5/16 7/16 1/2 1/2
Locking nut [mm] 17.5 20.0 24.5 37.0 41.0 50.0 58.0 63.0 64.0
M
length [inches] 11/16 13/16 15/16 1 7/16 1 5/8 1 15/16 2 5/16 2 1/2 2 1/2
Wrench
size ts [mm] 5 6 8 10 14 18 21 24 27
Stainless Steel
Stainless Steel Stainless Steel
316/316 Ti Stainless Steel Stainless Steel Stainless Steel
316/316Ti/ 316/316Ti/
2304/S32202/ 2205 316/316Ti 631
2205/2304 2205/2304
S32101 (Grade S460) (Grade S235) (1.4568)
Material (Grade S355) (Grade S460)
(Grade S460)
Finish A4 p Polished
Tension rods are grounded (bright finish), other parts are electropolished (matt finish), hand polished products are available on request.
Couplers
dsa
Regular couplers Couplers
with lugs
om
LM
+oj -oj
ds
ds
ds
kM
kM
dM
LM LM
Dimensions
System diameter [mm] 6 8 10 12 16 20 24 27 30
ds /dsk [inches] 1/4 5/16 3/8 1/2 5/8 13/16 15/16 1 1/16 1 3/16
Coupler [mm] 34 40 40 50 62 78 94 104 120
length LM
[inches] 1 5/16 1 9/16 1 9/16 1 15/16 2 7/16 3 1/16 3 11/16 4 1/8 4 3/4
Coupler [mm] 12 15 20 22 28 35 42 47 53
diameter dM
[inches] 1/2 9/16 13/16 7/8 1 1/8 1 3/8 1 5/8 1 7/8 2 1/16
Screw-in [mm] 10.5 12.5 15.0 18.5 22.5 27.0 34.0 37.5 42.5
depth om
[inches] 7/16 1/2 9/16 3/4 7/8 1 1/16 1 5/16 1 1/2 1 11/16
Length adjust- [mm] 4.5 4.5 5.0 6.5 7.5 8.0 11.0 12.5 12.5
ment oj
[inches] 3/16 3/16 3/16 1/4 5/16 5/16 7/16 1/2 1/2
Support system [mm] - - - 6 6 8 8 10 10
diam. dsa
[inches] - - - 1/4 1/4 5/16 5/16 3/8 3/8
[mm] - - - 27.5 33 37 44 50.5 57.5
Lug offset km
[inches] - - - 1 1/16 1 5/16 1 1/2 1 3/4 2 2 1/4
Øj
A B C D
45°only!
Øg
Øf
α min 40°
≈. 2.5 r
b
approx. 4.2 r
Note: A can only be used when simultaneously using the circular anchor disc at 45°, see page 7!
Dimensions
System diameter [mm] 6 8 10 12 16 20 24 27 30
ds /dsk [inches] 1/4 5/16 3/8 1/2 5/8 13/16 15/16 1 1/16 1 3/16
Connection [mm] 55 75 90 110 140 180 210 240 260
Øf
diameter [inches] 2 3/16 2 15/16 3 9/16 4 5/16 5 1/2 7 1/16 8 1/4 9 7/16 10 1/4
Disc [mm] 73 99 120 146 186 238 280 318 346
Øg
diameter [inches] 2 7/8 3 7/8 4 3/4 5 3/4 7 5/16 9 3/8 11 12 1/2 13 5/8
Plate [mm] 6 8 10 12 16 20 22 25 30
b
thickness [inches] 1/4 5/16 3/8 1/2 5/8 3/4 7/8 1 1 3/16
Pin hole [mm] 6.5 7.5 9.5 11.5 14.5 18.5 21.5 24.5 26.5
Øj
diameter [inches] 1/4 5/16 3/8 15/32 9/16 23/32 27/32 31/32 1 1/16
Pin hole [mm] 9 12 15 18 24 29 35 39 43
r
position [inches] 3/8 1/2 9/16 11/16 15/16 1 1/8 1 3/8 1 9/16 1 11/16
Min. plate [mm] 18 22 28 33 43 55 67 76 80
s
width [inches] 11/16 7/8 1 1/8 1 5/16 1 11/16 2 3/16 2 5/8 3 3 1/8
Compression Rod
To complement the DETAN Tension large diameter tubes, which are tapered forces and the span of the rod. Stain-
Rod System, HALFEN also offers mat- at each end so that standard DETAN less steel compression rods can also be
ching compression rods. These provide fork connectors can be used. Standard provided on request.
elegant technical and visual solutions assemblies are provided in carbon steel, The compression rods are delivered un-
for the support of structural compressi- and are dimensioned by HALFEN assembled.
on loads. Compression rods consist of according to the acting compression
System length L
System [mm]
ds Determined on a project basis
diameter [inches]
Minimum System Length L
[mm] 1000
[inches] 39 3/8
Maximum System Length L
[mm] 6340 6380 6440 6540 6610 6710
[inches] 249 251 253 257 260 264
Materials and designs of all components plus special designs → table below
System length L
Application of pretension
System diameter ds
System length L
System [mm] 30 36 42 48 52 56 60
ds
diameter [inches] 1 3/16 1 7/16 1 5/8 1 7/8 2 1/16 2 3/16 2 3/8
Cross section [mm²] 707 1018 1385 1810 2124 2463 2827
A
area [inches²] 1.095 1.577 2.146 2.805 3.292 3.817 4.381
Pretension Capacities
System [mm] 30 36 42 48 52 56 60
ds
diameter [inches] 1 3/16 1 7/16 1 5/8 1 7/8 2 1/16 2 3/16 2 3/8
Max. allow. [kN] 100 145 200 265 315 365 425
Nempf
pretension [kips] 22.50 32.63 45.00 59.63 70.88 82.13 95.63
System [mm] 30 36 42 48 52 56 60
ds
diameter [inches] 1 3/16 1 7/16 1 5/8 1 7/8 2 1/16 2 3/16 2 3/8
[mm] 120 140 158 180 195 210 245 LM Mv
Coupler
LM
ds
Coupler
dM
diameter [inches] 2 1/16 2 1/2 2 15/16 3 7/16 3 11/16 3 7/8 4 1/8
Questions or Comments?
Please contact us:
www.halfenusa.com
E-mail: info@halfenusa.com
Phone: 1 (800) 423 - 9140
Catalogues, Installation
Instructions & more at:
www.halfenusa.com