Doc No : CEE-UGL-MOS-001
Revision 20
CYCLECT Effective Date: 10-AUG-2018
COMPLETELY POSSIBLE Page :10f6
Method Of Statement For
MV Cable Installation Works
Prepared by Reviewed by | Approved by
Organization Cyclect UGL UGL
Signature LQ omDoc No CEE-UGL-MOS-001
Revision
CYCLECT Eecive Date | f0-AUG-2018
COMPLETELY POSSIBLE Page : 10f6
2.0
3.0
4.0
5.0
6.0
TABLE OF CONTENTS
Purpose and Scope
Health & Safety
Electrical Cable Installation
3.1 Plant and Equipment (Tools and Material)
3.2 Preliminary works
Work Methods
4.1 Cable Laying Works
4.2 Using Electrical Equipment’s
Emergency Properness & Teams
Review and Update1.0
2.0
Doc No CEE-UGL-MOS-001
Revision 20
Effective Date: 10-AUG-2018
Page 2 10f6
CYCLECT
COMPLETELY POSSIBLE
Scope of Work & Activity
The purpose of the method statement is to document the plan of activities
necessary for Electrical procedures.
Health & Safety
. A Safety/ Site Supervisor shall be on site when there are site activities
for the day to supervise and ready to act on all safety issues.
. Daily Toolbox Meeting (TBM) shall be conducted and recorded every
morning.
= All personnel at site shall attend Safety Induction Course before
commencing work.
* Suitable and appropriate Personal Protective Equipment (PPE) shall be
used according to the job requirement. PPE shall include the following:
Safety Helmet/ Hard Hat with Chin strap
Safety Glasses/ Goggles/ Face Shield
Ear Plugs/ Muffs
Reflective Vest
Hand Gloves (Rubber, Cotton, Leather, cut resistance)
Safety Hamess with lanyards attached to shock absorbers/
Restraint Belt
Safety Boots/ Shoes (Mid /High cut)
VVVVVY
v
* Working area as specified in the drawings shall be barricaded. Signage
shall be put up to prevent unauthorized personnel from entering the
work area and to caution passerby near the worksite.
* Housekeeping shall be done after the completion of work daily.Doc No : CEE-UGL-MOS-001
Revision 0
CYCLECT Effective Date; 10-AUG-2018
COMPLETELY POSSIBLE Page 10f6
3.0 Electrical Cable Installation Works
3.1
3.2
4.0
Equipment, Tools and Materials used
Equipment Tools Materials
= Ladders "| Electric Cutter = PVC pipes and
= Rec. Knife Accessories.
= Extension boxes * Cables Termination
= Screw driver/Test pen Accessories
= Multimeter
= _ Insulation Tester
Preliminary works before actual work commencement
Ensure no obstruction is observed on site.
Ensure temporary storage area is clean and dry.
Ensure confirm layout plan is ready for verifying information and
planning.
Affected work areas are to be barricaded.
Obtain relevant permits from the Main Contractor for the work
activities.
Work Methods
4.1 Cable Laying Works
Work permit should be acquired and displayed at working area.
Ensure all workers have attended the daily tool box meeting and brief on
the respective RA.
Each worker shall be properly equipped with PPE.
Ensure proper barricades and signages are display.
To checked & verified the cable specifications by Electrical Department.Doc No CEE-UGL-MOS-001
Revision 20
CYCLECT Effective Date: 10-AUG-2018
COMPLETELY POSSIBLE Page 1 10f6
* The area handover certificate shall be signed for clearance before
commencement of the cable pulling activity.
* The entire route shall be inspected to ensure that the trench routing is
complete, proper bends are used and free from any sharp edges.
* Using winch machine to pull cable.
* Make sure the winch machine inspected by LEW.
= Ensure proper communication using winch machine.
* Ensure the winch machine speed limit under control.
* Location of the Existing services and live cable shall be identified and
make sure.
* Access ladder shall be provided along the route of the cable trench where
required before commencing the cable laying on the trench.
* Before start of Cable pulling, the actual route length shall be measured
and checked for adequacy of cable length.
* Confirm that all Tools required for installation are available.
= Ensure sufficient quantity of Cable Tags is readily available.
= Check suitable position for placing the Cable pulling winch depending on
the length of the cable and the site condition.
= Personnel involved in the activity shall be made aware of the risks and the
steps to be taken to mitigate any hazard or unsafe situation.
= Ensure the trench shoring are not dismantle during cable pulling.
4.2 Using Electrical Equipment
* Ensure all electrical tools are in good working condition before and after
use.
* Workers must be equipped with proper PPES.
* Only trained workers may operate the equipment.
= Ensure all guards / safety devices are in place.
* All electrical tools must be checked monthly, by LEW and have a valid
sticker on it
= Do not use any defective tools or carry out unauthorized repair.
* Do not let electrical tools come into contact with water.
= Allelectrical equipment / extension cables shall be fitted with industrial
plug (not three-pin plugs).
* Donot over load any electrical outlet
* All wires shall be insulated and hung up to avoid contact with water and
avoid posing a tripping hazard.‘Doc No > CEE-UGL-MOS-001
Revision :0
+ 10-AUG-2018
CYCLECT Effective Date
COMPLETELY POSSIBLE Page 1 10f6
5. Emergency Preparedness &Teams
Stop all activities on site.
* Try to extinguish itifit is minor fire.
+ Immediately proceed to the assembly point.
+ Inform to the person-in-charge and alert others.
* Follow the fire warden instructions and direction.
6. Review and Update
This procedure, together with the risk assessment, shall be
reviewed every 3 years or when the following conditions occur
= After an injury / accident.
= After a major change of head of department or equipment
This Method Statement and all subsequent amendments shall be
kept for at least 3 years