Professional Documents
Culture Documents
Soundpaint SP150: Water Based Vibration Damping Compound
Soundpaint SP150: Water Based Vibration Damping Compound
FEATURES
x Non-sag formulation (thixotropic)
x IMO A653-16 compliant
x Excellent adhesion even to aluminium
x Cures to a hard chip resistant finish
x Non toxic
x Waterproof
x UV resistant
x Environmentally friendly
x Ignition retardant
x Broad temperature and frequency range
x Sprayable, air gun spray or airless spray
x Available with non slip surface texture
SOUNDPAINT® SP150 is fast drying, high solids x Paintable
water based viscoelastic vibration damping x Available in cream, grey and charcoal
compound. The unique formulation outperforms
other similar compounds. The exceptional APPLICATIONS
vibration damping properties are complemented
x Boat hulls, ceilings, decks and bulkheads
by ease of use, environmental friendliness and low
x Machinery and equipment enclosures
combustibility (dry film).
x Automotive
x Machinery guards
SOUNDPAINT SP150 is a thixotropic paste.
x Stainless steel fabrications eg sinks, bowls
SOUNDPAINT SP150 is specially designed for
x Dishwashers
trowel, brush, roll-on and air-gun spray
applications. Once dry the cured film is UV x Hospital equipment
resistant, water resistant and chip resistant. x Metal deck roof and metal wall cladding
x Whitegoods.
SOUNDPAINT SP150 is IMO A653-16 compliant. x Truck or bus underbodies,
x Heavy earthmoving equipment
Unlike most damping materials, SOUNDPAINT x Metal floors.
SP150 is a low-density product. The dry film is
light in weight without compromising high damping BENEFITS
performance. Consequently, this material is
x Tested to International marine fire standards
recommended for weight sensitive applications.
x Water based, easy application and clean up
eg. Aircraft, marine and automotive applications.
x Reduces resonant vibration
x Minimum weight for maximum performance
Vibration is absorbed by combining viscous,
x Excellent flame resistance
(energy dissipation) and elastic, (energy storage)
x Easy to install
characteristics. Vibration energy is absorbed
x Suitable for outdoor exposure
within the material and converted to heat.
x Eliminates tinniness and ringing
x Increases panel transmission loss
SOUNDPAINT SP150 effectively reduces resonant
x Ideal for weight sensitive applications
vibration. Increased transmission loss results from
x Extensional damping
the reduction of panel coincidence and panel
resonance effects.
80
70
60
P l a i n A l um i n i u m
50
40
30
SOU N D P A I N T A ppl i e d
20
10
0
25 40 63 100 160 250 400 630 1000 1600 2500 4000 6300 10000
Fr e qu e n c y ( H z )
80
70
P L A I N 3 mm G A L V A N I SE D
60
50
40
SO U N D P A I N T
30
20
10
0
25 40 63 100 160 250 400 630 1000 1600 2500 4000 6300 10000
F r eq uency ( Hz )
SPECIFICATIONS
STANDARD PRODUCT STANDARD PACK SIZES WEIGHT
SOUNDPAINT SP150-015 15 litres 20kg
SOUNDPAINT SP150-200 200 litres 300kg
FLAMMABILITY PROPERTIES
MATERIAL MVSS-302 SAEJ369a IMO A653.16
SOUNDPAINT SP150 SE* SE* Complies
* Self Extinguishing
MISCELLANEOUS PROPERTIES
MATERIAL COLOURS SPECIFIC RECOMMENDED SERVICE TEMP
GRAVITY OPERATING TEMP RANGE
RANGE
GREY, CREAM, 1.8 – 2.0 0 0 0 0
SOUNDPAINT SP150 0 C to 60 C -40 C to +160 C
CHARCOAL (Dry Film)
CHEMICAL RESISTANCE
MATERIAL UV H20 PETROL DIESEL 10% HCL 10% NaOH
SOLUT. Solution
SOUNDPAINT SP150 Excellent Excellent Good Good Good Good
Application Temperature:
o
Apply SOUNDPAINT SP150 at temperatures above 15 C
o
Metal Temperatures need to be greater than 10 C
o
Storage: Store above 10 C
Shelf Life: 12 months in an unopened container.
Return To Index
® ®
8/04/2008 SOUNDPAINT and SOUNDGUARD are Registered Trademarks of Pyrotek P/L Page 2
This document is covered by Pyrotek standard Disclaimer, Warranty and © Copyright clauses.
AUSTRALIA: +61 (0)2 8868 2088 CHINA: +86 (0) 755 8601 6743 DUBAI: +971 (50) 624 9254
NEW ZEALAND: +64 (0)9 272 2056 TAIWAN: +886 7 224 8222 USA: +1 509 926 6212
SOUNDPAINT SP150 www.soundguard.com.au
APPLICATION GUIDE
SOUNDPAINT SP150
Water Based Vibration Damping Compound
1. Surface Preparation
The product has been specifically formulated to provide high adhesion to difficult substrates such as uncoated
Aluminium. However, the surface must be prepared as if for painting eg:
x Remove any dust, dirt, oil, grease, rust, mould-release agent, etc. from the surface.
x Abrading the surface by wire brushing, sandblasting or abrasive paper is recommended for highly polished
surfaces, to obtain the best possible adhesion
x Degrease the surface using a solvent wipe of Xylene, Toluol, Methylene Chloride or similar solvent. (Take all
necessary precautions when using flammable solvent materials. Consult the MSDS for the chosen material
before use.)
x Alternatively use a water based surfactant cleaning system (detergent). After cleaning ensure that all traces
of surfactant (detergent) are removed by flushing the surface with clean water.
x On mild and carbon steel, a rust preventing prime coat is recommended to prevent rusting.
2. Mixing
SOUNDPAINT SP150 is shipped at proper viscosity. If a thinner consistency is needed for spray by an air gun
or body deadener gun, add a small amount of methylated spirits or water (a maximum of 3% by weight) and stir
the product thoroughly.
5. Application Methods
a: Trowel on: Normal notched trowel used to apply a 1-3mm wet film is suitable
20L Bottom Out Press Pot Texture Coat Kit – 02220 - BMTRK
c: Air Spray – Venturi type deadener gun suited to application of textured finishes.
NB: Only suited to low volume application.
x Body Deadener Gun - Gun Nozzle: 4mm – 6mm
Air pressure: > 80psi
6. Application Temperature
x Do not apply if the ambient temperature falls below 10ºC.
7. Clean Up
x Clean up equipment with water after use.