Professional Documents
Culture Documents
Ei6301-Electrical Measurements Question PDF
Ei6301-Electrical Measurements Question PDF
Ei6301-Electrical Measurements Question PDF
EI6301-ELECTRICAL MEASUREMENTS
QUESTION BANK
UNIT I –MEASUREMNET OF VOLTAGE AND CURRENT
PART – A (2 MARKS)
1. A permanent magnet moving coil instrument has full scale deflection of 75μA and a coil
resistance of 1KΩ. Calculate the required shunt resistance value to convert the
instrument into an ammeter with full scale deflection of 75mA (B.T-3)
2. Give the torque equation for an electro dynamometer type wattmeter (B.T-2)
3. How do you define rectifier type of instruments? (B.T-1)
4. Recommend the type of resistor connection to extend the range of voltmeter in PMMC
instruments (B.T-5)
5. Interpret the term transfer instrument (B.T-2)
6. Identify the main sources of errors in PMMC instruments (B.T-1)
7. List the methods of calibrating a ballistic galvanometer (B.T-1)
8. How do you infer the term error? (B.T-4)
9. Generalize on how the range of instruments can be extended in PMMC instruments
(B.T-6)
10. Define calibration (B.T-1)
11. List the basic requirements of any measuring instruments (B.T-1)
12. Contrast the advantages and disadvantages of moving iron instruments (B.T-4)
13. Examine why the scale in the MI instrument is non linear? (B.T-3)
14. Discuss few advantages of using D’Arsonval galvanometer for measurement purpose
(B.T-2)
15. Compare spring control and gravity control (B.T-4)
16. Give the expression for deflection in MI ammeter (B.T-2)
17. Formulate to convert basic instruments in PMMC into higher ranger ammeter (B.T-6)
18. Show the basic constructional diagram of attraction type moving iron meter (B.T-3)
19. Is it possible to measure DC and AC using permanent magnet moving coil type
instrument? Explain (B.T-5)
20. Describe the type of control system and damping system are used in dynamometer
instrument (B.T-1)
PART – B (16 MARKS)
1. i) Illustrate with neat diagram the construction and working principle of (8)
attraction and repulsion type MI instruments (B.T-3)
Prepared by: Mr. I. Andrew Xavier Raj – AP(OG) & Mr. G. Shiva – AP(OG) 2016-2017
VALLIAMMAI ENGINEERING COLLEGE Dept of EIE
ii) Obtain expression for deflection of D’Arsonval galvanometer. Explain step (6)
by step (B.T-4)
3. Sketch the basic construction of PMMC instrument. Develop the torque equation (16)
for a PMMC instrument and show that its scale is linear if spring control is
employed (B.T-6)
5. i) Explain the operation of Dynamometer type ammeter with torque equation (10)
(B.T-4)
ii) A moving coil instrument gives a full scale deflection of 1mA when the (6)
potential difference across its terminals is 10mV. Calculate both the shunt
resistance for a full scale deflection corresponding to 10A and the series
resistance for full scale reading with 100V and what do you infer from it
(B.T-4)
6. Describe the step by step procedure on Calibration of ballistic galvanometer (B.T- (16)
1)
ii) Discuss how the range of a PMMC voltmeter and ammeter be extended? (6)
(B.T-2)
8. Describe the construction and working of a ballistic galvanometer. How do you (16)
conclude that in a ballistic galvanometer, the charge is proportional to first swing
of the moving coil (B.T-5)
9. i) Describe the working of a rectifier type instrument which uses a Half Wave (8)
Rectifier (B.T-2)
ii) Discuss the factors affecting the performance of Rectifier type instruments (8)
(B.T-2)
10. Define Thermo Electric Instruments. Classify and explain any two of them (B.T- (16)
1)
11. Tabulate the features of PMMC, MI and Dynamometer type of instruments (B.T- (16)
1)
12. Distinguish between Half Wave Rectifier type instruments and Full Wave (16)
Rectifier type of instruments using form factor, accuracy and other features also
(B.T-2)
Prepared by: Mr. I. Andrew Xavier Raj – AP(OG) & Mr. G. Shiva – AP(OG) 2016-2017
VALLIAMMAI ENGINEERING COLLEGE Dept of EIE
13. Illustrate how MI instruments can be used for both AC and DC measurement (16)
using construction diagram with different vane arrangements. Justify why MI
instruments cannot be accurate for DC measurement (B.T-3)
14. (i) Explain the construction and operation of Thermocouple type instrument (8)
(B.T-4)
(ii) Explain the different types of Rectifier circuits and obtain the voltage (8)
equation for each type (B.T-4)
PART – A (2 MARKS)
1. i) With a neat sketch describe the construction and working principle of (10)
dynamometer type wattmeter. Develop its torque equation (B.T-1)
Prepared by: Mr. I. Andrew Xavier Raj – AP(OG) & Mr. G. Shiva – AP(OG) 2016-2017
VALLIAMMAI ENGINEERING COLLEGE Dept of EIE
ii) An energy meter is designed to make 100 revolutions of disc for one unit of (6)
energy. Calculate the number of revolution made by it when connected to load
carrying 40 A at 230V and 0.4 PF for an hour. Calculate the percentage of error
if it actually makes 360 revolutions (B.T-3)
3. A 220V 5A DC energy meter is tested at its marked ratings. The resistance of the (16)
pressure circuit is 8800Ω and that of current coil is 0.1 Ω. Calculate the power
consumed in when testing the meter with
4. (i) List out various type of errors in dynamometer wattmeter (B.T-1) (8)
5. Develop the step by step procedure for calibrating LPF wattmeter by phantom (16)
loading (B.T-6)
6. Explain how power can be measured in a 3 phase circuit with the help of two watt (16)
meters (B.T-4)
7. A 230V single phase watt-hour meter has a constant load of 4A passing through it (16)
for 6 hours at unity pf. If the meter disc makes 2208 revolutions during this period,
what are the meter constants in revolutions per KWh. Express the power factor of
the load if the no of revolutions made by the meter are 1472 when operating at 230V
and 5A for 4 hours (B.T-2)
8. i) Describe the lag adjustments and friction compensation made in single phase (8)
induction type energy meters (B.T-1)
9. With neat sketch and phasor diagram discuss the construction and operation of (16)
induction type single phase energy meter (B.T-2)
10. Assess the various adjustments available in single phase energy meters to get the (16)
accurate reading (B.T-5)
11. Explain the operation of three phase energy meter with neat sketch (B.T-4) (16)
12. (i) List the different types of errors occurring in wattmeter and write short notes (8)
on it (B.T-1)
Prepared by: Mr. I. Andrew Xavier Raj – AP(OG) & Mr. G. Shiva – AP(OG) 2016-2017
VALLIAMMAI ENGINEERING COLLEGE Dept of EIE
(ii) Examine how two numbers of wattmeter are sufficient for three phase power (8)
measurement instead of three numbers of wattmeter. Show it with an example
(B.T-1)
13. Discuss the registering mechanisms used in energy meters with neat sketches (B.T- (16)
2)
14. (i) Illustrate how phasor diagram can be drawn in three phase circuits (B.T-3) (8)
(ii) Explain the terms active power, reactive power and apparent power in three (8)
phase circuits. Write short note on Power triangle (B.T-4)
PART – A (2 MARKS)
1. Develop a circuit for measuring high voltage and high current with the help of PT (16)
and CT. What purpose do they serve? (B.T-6)
Prepared by: Mr. I. Andrew Xavier Raj – AP(OG) & Mr. G. Shiva – AP(OG) 2016-2017
VALLIAMMAI ENGINEERING COLLEGE Dept of EIE
2. Explain the use of instrument transformer for the measurement of power with a (16)
neat diagram (B.T-5)
3. Draw and explain the circuit of a basic potentiometer. Explain how the (16)
potentiometer should be calibrated and how it is used for the precise measurement
of DC voltage (B.T-4)
4. i) List the functions of transfer instrument and phase shifting transformer (8)
(B.T-1)
ii) List two applications of D.C potentiometers and write short notes on it (8)
(B.T-1)
ii) Summarize the applications of A.C potentiometers with neat sketch (B.T-2) (8)
7. Discuss the constructional features of C.T and P.T and explain how they are used (16)
to extend the range of instruments (B.T-2)
ii) A current transformer rated as 1000/5A, 25 VA has a turn ratio of 1:200. (8)
The core loss and magnetizing components of the primary currents are 5A
and 8A under rated conditions. Calculate the ratio and phase angle errors
for the rated burden and rated secondary current at 0.8pf lagging (B.T-3)
9. With neat sketch describe the principle and explain construction & operation of (16)
polar type Drysdale A.C potentiometer (B.T-1)
10. Describe the basic circuit construction and operation of Crompton laboratory type (16)
D.C potentiometer (B.T-1)
Prepared by: Mr. I. Andrew Xavier Raj – AP(OG) & Mr. G. Shiva – AP(OG) 2016-2017
VALLIAMMAI ENGINEERING COLLEGE Dept of EIE
11. (i) List the different types of ratios present in instrument transformers and write (8)
how it is calculated (B.T-1)
(ii) Describe the method of construction and operation of C.T and P.T (B.T-1) (8)
12. Summarize briefly about the property of materials used in Instrument (16)
transformers construction (B.T-2)
13. (i) Explain the disadvantages of using shunts and multipliers while measuring (6)
high values of current and voltages (B.T-4)
(ii) A 1000/5A Current Transformer has the magnetizing current of 1A, it is (10)
being operated at full load primary current and with a secondary burden of
non-inductive resistance of 1ohm at power factor of 0.4. Calculate
ii. The ratio error at full load. Assuming that there are no compensation
(B.T-3)
14. (i) A 500/100 V potential transformer has the following constants: (8)
ii. The value of secondary winding current at unity power factor when
the phase angle is zero (B.T-4)
PART – A (2 MARKS)
1. List the difficulties in high resistance measurement and method to overcome them
(B.T-1)
Prepared by: Mr. I. Andrew Xavier Raj – AP(OG) & Mr. G. Shiva – AP(OG) 2016-2017
VALLIAMMAI ENGINEERING COLLEGE Dept of EIE
1. i) List the difficulties in the measurement of high resistance and direct (8)
deflection method for measurement of high resistance (B.T-1)
ii) Describe the construction and working of shunt type ohmmeter (B.T-1) (8)
2. Describe measurement of resistance using kelvin double bridge method and (16)
obtain expression for unknown resistance (B.T-1)
3. With neat sketch express the measurement of high resistance using price’s guard (16)
wire method (B.T-2)
Prepared by: Mr. I. Andrew Xavier Raj – AP(OG) & Mr. G. Shiva – AP(OG) 2016-2017
VALLIAMMAI ENGINEERING COLLEGE Dept of EIE
5. (i) Design a series type ohmmeter. The movement to be used requires 0.5 (8)
mA for full scale deflection and has an internal resistance of 50Ω. The
internal battery has a voltage of 3V. The desired value of half scale
resistance is 3000 Ω. Differentiate and explain the method to obtain
(b) The range of values of parallel resistance, if the battery voltage may vary
from 2.7V to 3.1V. Use the value of the series resistance calculated above
(B.T-4)
ii) A shunt type ohmmeter uses a 10mA basic D’Arsonval movement with (8)
an internal resistance of 5Ω. The battery emf is 3V. It is desired to modify
the circuit by adding appropriate shunt resistance across the movement so
that its instrument indicates 0.5Ω at the midscale. Separate the value of shunt
resistance and value of current limiting resistor (B.T-4)
ii) Describe the circuit of Kelvin double bridge used for measuring low (10)
resistance (B.T-1)
7. i) Explain how Earth Tester used for measurement of resistance of earth? (8)
(B.T-4)
ii) Explain the Loss of charge method for Measurement of insulation (4)
resistance of cables (B.T-4)
iii) Draw the circuit of a Wheat stone bridge and deduce the conditions for (4)
balance (B.T-5)
8. i) Differentiate shunt type ohmmeter from series type ohmmeter with neat (8)
sketch (B.T-2)
ii) Explain how the earth resistance can be measured using three point fall of (8)
potential method (B.T-4)
Prepared by: Mr. I. Andrew Xavier Raj – AP(OG) & Mr. G. Shiva – AP(OG) 2016-2017
VALLIAMMAI ENGINEERING COLLEGE Dept of EIE
ii) b (8)
P Q
G
c
a
R S
d
10. i) The ratio arms of a kelvin bridge are 100Ω each. The galvanometer has (8)
an internal resistance of 500Ω and a current sensitivity of 200mm/μ A.
The unknown resistance is 0.1002 Ω and the standard resistance is set at
0.1000Ω. DC current of 10 A is passed through the standard and the
unknown resistance form a 2.2V battery in series with a rheostat.
Calculate the deflection of the galvanometer. Neglect the resistance of the
link. Also substitute the unbalance resistance value to produce a
deflection of 1mm. (B.T-6)
ii) List the categories of resistances based on their values and list the (8)
methods of measuring it. Describe the necessity for various methods
employed in measuring the resistance values (B.T-1)
ii) In a Wheatstone bridge circuit, the values of resistances are P= 1000 Ω, (6)
Q= 100 Ω, R= 2005 Ω and S= 200 Ω. The battery has an emf of 5V and
negligible internal resistance. The galvanometer has a current sensitivity
of 10mm/microAmp and an internal resistance of 100 Ω. Connect the
deflection of galvanometer and the sensitivity of the bridge in the terms
of deflection per unit change in resistance (B.T-4)
12. i) A cable of length 1000m is tested for insulation resistance by the loss of (8)
charge method. An electrostatic voltmeter of infinite resistance is
connected between the cable conductor and the earth forming a joint
capacitance of 8x10-4 µF. It is observed that after charging, voltage falls
from 400 to 200V in 50secs. Calculate insulation resistance of the cable
of length 500m (B.T-3)
Prepared by: Mr. I. Andrew Xavier Raj – AP(OG) & Mr. G. Shiva – AP(OG) 2016-2017
VALLIAMMAI ENGINEERING COLLEGE Dept of EIE
ii) Calculate insulation resistance of a cable in which the voltage falls from (4)
100 to 80V in 20secs. The capacitance is 300pF (B.T-3)
13. i) What are the different problems associated with measurement of low (10)
resistance? Describe the procedure to eliminate the effects of contact
resistance and lead resistance in Kelvin Double Bridge (B.T-2)
ii) The ohm meter has Eb= 1.5V, resistance R1=15K Ω in series with Rx, (6)
Rm= 50 Ω, parallel resistance R2= 50 Ω and meter FSD = 50micro
ampere. Calculate the ohm meter scale at 0.5 FSD and determine the new
resistance value that R2 must be adjusted to when Eb falls to 1.3V. Also
rearrange the value of Rx at 0.5 FSD when Eb= 1.3V(B.T-6)
14. Discuss the various methods involved in high resistances measurement. Explain (16)
any one of them (B.T-2)
PART – A (2 MARKS)
Prepared by: Mr. I. Andrew Xavier Raj – AP(OG) & Mr. G. Shiva – AP(OG) 2016-2017
VALLIAMMAI ENGINEERING COLLEGE Dept of EIE
1. i) Draw and explain the working of Maxwell’s bridge. Derive the condition for (10)
the balance of the bridge (B.T-4)
ii) A Maxwell bridge is used to measure an Inductive impedance. The bridge (6)
constants at balance are:
C1 0.01 F , R1 470K , R 2 5.1K , R 3 100K . . Calculate Lx and Rx
(B.T-3)
2. What are the conditions for balancing the AC bridge? Describe the working of (16)
Schering bridge for the measurement of capacitance with neat diagram. Derive the
equations for balance (B.T-2)
3. Explain in detail the procedure of measurement of inductance and capacitance (B.T- (16)
4)
ii) The arms of a 4 arm bridge abcd supplied with the sinusoidal voltage, have the (8)
following values :Arm ab has 200Ω in parallel with 1 µF, arm bc has 400Ω,
arm cd has 1000Ω and arm ba has resistance R2in series with 2µF. Calculate
the value of R2and the frequency at which the bridge will balance. (B.T-3)
5. i) Identify the circuit diagram and phasor diagram for Anderson bridge. (B.T-1) (8)
ii) Examine the expression for unknown inductance in Anderson Bridge (B.T-1) (8)
6. Explain the measurement of inductance using maxwell-wein’s bridge circuit (B.T- (16)
5)
7. What are the different sources of errors in AC bridges? Explain the precautions (16)
taken and the techniques used for elimination of these errors (B.T-4)
ii) List the special features of a high voltage Schering bridge (B.T-1) (8)
9. i) List the source of errors in bridge circuit and discuss the precautions and (6)
techniques used for reducing errors (B.T-1)
Prepared by: Mr. I. Andrew Xavier Raj – AP(OG) & Mr. G. Shiva – AP(OG) 2016-2017
VALLIAMMAI ENGINEERING COLLEGE Dept of EIE
ii) Examine how to measure relative permittivity with Schering bridge. (B.T-1) (10)
10. An bridge has 4 arms arm ab is 0.2µF, arm bc is 500Ω, arm cd consists of unknown (16)
impedance and arm da has a 300Ω in parallel with 0.1 µF. Calculate the R and C or
L constants of arm cd considering as a series circuit. (B.T-3)
11. i) Identify and draw the phasor diagram of Maxwell Inductance Bridge (B.T-1) (8)
ii) Identify how to measure mutual inductance using bridge circuit(B.T-1) (8)
12. i) A capacitor bushing forms arm ab in a schering bridge and a standard capacitor (8)
of 500pF with negligible loss forms arm ad. Arm bc consists of a non-
inductive resistance of 300 Ω. When the bridge is balance, arm cd has a
resistance of 72.6 Ω parallel with a capacitance of 0.148 µF. The supply
frequency is 50Hz. Develop the capacitance and dielectric loss angle of
capacitorusing appropriate assumption (B.T-6)
ii) List the errors in AC bridges and their compensation (B.T-1) (8)
ii) Describe and derive the equation in Hay’s Bridge (B.T-2) (8)
ii) The four arms of an AC bridge contain the following elements: PQ, a coil of (8)
unknown impedance; QR, a non-inductive resistor of 1000Ω; RS, a non-
inductive resistor of 85 Ω in series with a standard capacitor of 0.35 µF; SP, a
pure resistor of 16,500 Ω. The supply frequency is connected to points P and
R, and a detector to point Q and S. Separate and identify the inductance and
resistance values of the coil. (B.T-4)
Prepared by: Mr. I. Andrew Xavier Raj – AP(OG) & Mr. G. Shiva – AP(OG) 2016-2017