Professional Documents
Culture Documents
Topic 2force en Ali
Topic 2force en Ali
Two or more forces acting on a body can be replaced by a single force that
is called a resultant force.
Conversely, it is also possible to split or resolve one force into two forces.
These forces are called the components of the original force. The process
of splitting or resolving a force into its components is called resolution.
A force can cause a stationary body to move or alter the speed and
direction of a moving body. A change in velocity of a body is an
acceleration. Therefore, a force causes an acceleration.
Because both the magnitude and direction of a force are significant, forces
are vector quantities. Types of forces in mechanics include weight, pushes
and pulls, friction, normal reaction, tension and thrust.
i) its magnitude
ii) its direction
iii) its point of action
iv) the type of force
Newton’s first law of motion states that a body will continue in its state of rest or
uniform motion unless a resultant external force acts on it.
As a consequence:
If a body is not accelerating the forces acting upon it must be in equilibrium – the
resultant external force must be zero.
1
Newton’s second law of motion (Hukum Newton II):
Newton’s second law of motion states that the rate of change of momentum of a
moving body is proportional to the resultant external force acting on the body and
takes place in the direction of the force.
∑ F = ma
Newton’s third law of motion states that if a body A exerts a force on a body B,
then B exerts an equal and opposite force on A.
This is sometimes stated as “ Action and reaction are equal and opposite “
FA
FB
FA (action) = FB (reaction)
The SI unit of force is the newton(N). One newton is the force required to give a
mass of 1 kilogram an acceleration of 1 metre per second per second ( 1 m/s2 ).
1 N = 1 kg.m/s2
2
F = m a, therefore,
1N 1kg
1 m/s2
2N 1kg
2 m/s2
3N 1kg
3 m/s2
a) No resultant force must act. If a resultant force acts then the system
would accelerate and would therefore not be in equilibrium.
∑ Fx = 0, ∑ Fy = 0
∑M = 0
Examples:
1)
8N 8N
∑ F = R = 8 – 8 = 0 ( state of equilibrium)
3
2)
F3 = 2 N
F1 = 4 N F2 = 4 N
F4 = 2 N
∑ F x = Rx = F 1 – F 2 = 4 – 4 = 0 N
∑ F y = Ry = F 3 – F 4 = 2 – 2 = 0 N
( state of equilibrium )
3)
8N
4N
7N 4N
3N 6N
6N 6N
∑ Fx = Rx = (4 + 6) - (7 + 3) = 0 N
∑ Fy = Ry = (4 + 8) - (6 + 6) = 0 N
( state of equilibrium )
4
4) For three forces F1, F2 and F3 acting at point P, if ∑ F = 0, they will form
a closed triangle.
F1
F1 F3
F2
F2
F3
i) Definition:
It is common for more than one force to act on a body simultaneously. When this
occurs the forces are said to be concurrent, if they act at the same point, and
coplanar if they lie within the same plane.
The net force that acts on an object when two or more forces act on it is known as
the resultant force. If the forces act in the same straight line the resultant is found
by simple addition or subtraction as shown in Figure 2.6.1.
5N 3N 4N 7N
a) R = 5 + 3 = 8 N b) R = 7 - 3 = 8 N
Figure 2.6.1
5
The resultant of forces that do not act in the same straight line can be determined
by using the parallelogram law. The parallelogram law states that if two forces
acting at a point are represented in size and direction by the sides of a
parallelogram drawn from the point, their resultant is represented in size and
direction by the diagonal of the parallogram drawn from the point.
Using the parallelogram law, the resultant of the forces P and Q in Figure 2.6.2(a)
is thus represented by R in Figure 2.6.2(b).
R
P P
θ
O O
Q Q
(a) (b)
Figure 2.6.2
___________________
R = P2 + Q2 + 2PQ cos θ … [ because cos (180 – θ) = - cos θ ]
R
P
α
Q
180 O - θ
6
Examples:
1) Two concurrent forces of 3 N and 4 N act at a body at right angles to one another.
Determine the magnitude and direction of the resultant force.
Solution:
(i)
Scale 1 N : 1 cm
3 N = 3 cm, 4 N = 4 cm
A C
R
3 cm
900
α
B
O 4 cm
Figure 2.6.3
( ii ) P = 3 N, Q = 4 N, θ = 900
R = ( P2 + Q2 + 2PQcos θ )
= [ 32 + 42 + 2(3)(4)cos 900 ]
= 5N
7
2) Compute the resultant forces produce by the following system of forces:
i) ii)
1.5 kN
8N
600 800
O O
12 N 1 kN
Solution:
i)
Scale 1 cm : 1 N
A C
8N R
600
α
O B
12 N
Direction of R, α = 240
Or,
R = ( P2 + Q2 + 2PQcos θ
= 17.4 N
8
ii)
A C
Scale 1cm: 100 N
1.5 kN R
800
α
O B
1 kN
Direction of R, α = 500
Or,
3) A resultant force of 130 N was produced by the action of two concurrent forces with
the magnitudes of 70 N and 80 N. Find the magnitude of the angle made by the
forces of 70 N and 80 N.
Solution:
130 N
70 N
80 N
9
R2 = P2 + Q2 + 2PQcos θ
Definition:
Any single force may be split into two components. This is, in fact, the reverse of
combining two forces into a resultant force. In this case the single force is resolved
into two other forces.
The most useful way to resolve a single force into two forces is to produce
components which are perpendicular to each other.
F
F
Fsinθ
Fcosθ
The force F can be resolved into the two perpendicular forces: Fcosθ and Fsinθ.
Definition:
When multiple forces act at a point, it is necessary to resolve each of the separate
forces into a particular direction and then find the sum of all of the resolved
components in that direction.
For example, to find the resultant of the following four forces we need to resolve each
force into the directions Ox and Oy and sum for each direction. We can then find the
resultant of the two concurrent forces.
10
y
2N
4N
O
x
600
5 N 200 6N
Note: The result is negative indicating that it is in the downward direction. The 4 N
force has no component in the Oy direction.
Once all four forces have been resolved into two perpendicular components, the
resultant force and direction can be determined.
7.49 N
5.70 N
R
______________
R = 7.492 + 5.702 = 9.41 N
tan θ = 5.70
7.49
θ = tan-1 (5.70/7.49) = 370
11
Lami’s Theorem:
The triangle of forces is used to analyse three force problems where all of the vector
magnitudes are known or may be determined easily. In situations where the angles
between the forces are known or may be easier to use Lami’s theorem, which is an
adaptation of the sine rule.
If three concurrent forces are in equilibrium, each force is proportional to the sine of
the angle between the other two forces.
F1
θ2
θ3
F3
θ1
F2
F1 F2 F3
-------- = -------- = ---------
sin θ1 sin θ2 sin θ3
Examples
F1
15 N
γ
1300 1200
F2
Solution
F1 15
12
---------- = ----------
sin 1200 sin 1300
F2 = 15 sin 1200 = 17 N
sin 1300
F2 15
---------- = -----------
sin 1100 sin 1300
2) The diagram shows a particle in equilibrium being acted on by three forces. Find
the value P.
.
1200
Q
900
20 N
Solution
P 20
--------- = ----------
sin 900 sin 1200
P = 20 sin 900 = 23 N
sin 1200
13
600 300
T1
T2
Solution
T1 T2
900
1500
1200
20 N
T1 20
---------- = ---------
sin 1200 sin 900
T2 20
----------- = -----------
sin 1500 sin 900
T2 = 20 sin 1500 = 10 N
sin 900
14
figure below. If the reading of the spring balance is 30 N, find
T
θ
30 N
Solution
a)
T cosθ
θ
30 N
Tsin θ
20 N
∑ Fx = 30 – T sin θ = 0
T sin θ = 30 ---- ( I )
∑ Fy = T cos θ – 20 = 0
T cos θ = 20 ---- ( II )
Dividing equation ( I ) by equation ( II ),
T sin θ = 30
15
T cos θ 20
tan θ = 1.5
θ = 56.30
T sin 56.30 = 30
30
T = ----------- = 36 N
sin 56.30
If one or more non-concurrent forces act on a rigid body they may cause it to rotate
about an axis. The turning effect of non-concurrent forces acting on a rigid body is
measured by the moment of the force about this axis.
The moment of a force about an axis is the product of the magnitude of the force
and the perpendicular distance from the line of action of the force to the axis.
x d
O
The diagram shows a rigid bar being acted on by a force F at a pont x on the bar.
The force causes the bar to rotate about a point O.
Examples
16
1) Find the magnitude and sense of the moment of the given force about O?
8N
O
2m
MO = F x d = 8 x 2 = 16 Nm ( )
2) Determine the net moment at O produced by the action of the two forces below.
O 2m
3m
10 N
5N
∑ MO = ( 10 x 5 ) - ( 5 x 2 ) = 50 - 10 = 40 Nm
3) Find the magnitude and sense of the moment of the given force about O?
4m
O
300
18 N
0
M0 = ( 18 sin 30 ) x 4 = 36 Nm
17
4) The following diagram shows a uniform square lamina ABCD subject to several
forces. Find the resultant moment about A.
6N
D E C
4N 1N 2m
2N
A B
1m 3N
MA = ( 6 x 2 ) - ( 4 x 1 ) - ( 1 x 2) = 6 Nm
5) In the diagram below, the rod XY is free to rotate about the point X. The forces
shown are 1 m, 3 m and 7 m from X respectively. Find the moment about X of
each of the forces and then determine the magnitude and sense of the resultant
moment about X.
15 N
X Y
300
5N
10 N
Mx = ( 15 x 1 ) - ( 5 x 3 ) - [ ( 10sin 300 ) x 7 ] = - 35 Nm
18