Professional Documents
Culture Documents
Quad Transceiver, Inverting (3-State) Quad Transceiver (3-State)
Quad Transceiver, Inverting (3-State) Quad Transceiver (3-State)
74F242
Quad transceiver, inverting (3-State)
74F243
Quad transceiver (3-State)
Philips Semiconductors Product specification
Transceivers 74F242/74F243
PIN CONFIGURATION
TYPICAL TYPICAL
OEA 1 14 VCC TYPE PROPAGATION SUPPLY CURRENT
DELAY (TOTAL)
NC 2 13 OEB
74F242 4.3ns 31.2mA
A0 3 12 NC
A1 4 11 B0
74F243 4.0ns 66mA
A2 5 10 B1
ORDERING INFORMATION
A3 6 9 B2
COMMERCIAL RANGE
GND 7 8 B3
DESCRIPTION VCC = 5V ±10%, PKG DWG #
Tamb = 0°C to +70°C
SF00765
14-pin plastic DIP N74F242N, N74F243N SOT27-1
14-pin plastic SO N74F242D, N74F243D SOT108-1
LOGIC SYMBOLS
74F242
74F243
3 4 5 6
3 4 5 6
A0 A1 A2 A3
A0 A1 A2 A3
1 OEA
1 OEA
13 OEB
13 OEB
B0 B1 B2 B3
B0 B1 B2 B3
VCC = Pin 14
GND = Pin 7 11 10 9 8
VCC = Pin 14 11 10 9 8
GND = Pin 7
SF00767 SF00768
Transceivers 74F242/74F243
3 11 3 11
1 1
2 2
4 10 4 10
5 9 5 9
6 8 6 8
SF00769 SF00770
74F243
74F242
1 1
OEA OEA
3 11 3 11
A0 B0 A0 B0
4 10 4 10
A1 B1 A1 B1
5 9 5 9
A2 B2 A2 B2
6 8 6 8
A3 B3 A3 B3
13 13
OEB OEB
VCC = Pin 14 VCC = Pin 14
GND = Pin 7 SF00771 GND = Pin 7 SF00772
LOGIC DIAGRAMS
FUNCTION TABLE, 74F242 FUNCTION TABLE, 74F243
INPUTS OUTPUTS INPUTS OUTPUTS
OEA OEB An Bn OEA OEB An Bn
L L INPUT B=A L L INPUT B=A
H L Z Z H L Z Z
L H a a L H a a
H H A=B INPUT H H A=B INPUT
H = High voltage level
L = Low voltage level
Z = High impedance “off” state
a = This condition is not allowed due to excessive currents
1990 Aug 30 3
Philips Semiconductors Product specification
Transceivers 74F242/74F243
1990 Aug 30 4
Philips Semiconductors Product specification
Transceivers 74F242/74F243
DC ELECTRICAL CHARACTERISTICS
(Over recommended operating free-air temperature range unless otherwise noted.)
LIMITS
SYMBOL PARAMETER TEST CONDITIONS1 UNIT
MIN TYP2 MAX
VCC = MIN, ±10%VCC 2.4
VIL = MAX
MAX, IOH
O = –3mA
3mA V
VIH = MIN ±5%VCC 2.7 3.3
VOH High level output voltage
High-level
VCC = MIN, ±10%VCC 2.0 3.2
VIL = MAX
MAX, IOL = –15mA
15mA V
VIH = MIN ±5%VCC 2.0 3.1
1990 Aug 30 5
Philips Semiconductors Product specification
Transceivers 74F242/74F243
AC ELECTRICAL CHARACTERISTICS
LIMITS
VCC = +5V VCC = +5V ± 10%
TEST
SYMBOL PARAMETER Tamb = +25°C Tamb = 0°C to +70°C UNIT
CONDITION
CL = 50pF, RL = 500Ω CL = 50pF, RL = 500Ω
MIN TYP MAX MIN MAX
tPLH Propagation delay Waveform 2.5 3.5 6.0 2.5 7.0
ns
tPHL An, Bn to Bn, An NO TAG 2.0 3.0 4.5 2.0 4.5
tPZH Output Enable time Waveform 3 3.0 4.0 7.0 3.0 8.0
74F242 ns
tPZL to High or Low level Waveform 4 3.5 6.5 9.0 3.5 10.5
tPHZ Output Disable time Waveform 3 3.5 5.5 8.5 3.5 9.0
ns
tPLZ from High or Low level Waveform 4 3.5 6.0 9.5 3.5 11.0
tPLH Propagation delay 2.5 4.0 5.2 2.0 6.2
Waveform 2 ns
tPHL An, Bn to Bn, An 2.5 4.0 5.2 2.0 6.5
tPZH Output Enable time Waveform 3 2.0 4.5 5.7 2.0 6.7
74F243 ns
tPZL to High or Low level Waveform 4 2.0 5.0 7.5 2.0 8.5
tPHZ Output Disable time Waveform 3 2.0 4.0 6.0 2.0 7.0
ns
tPLZ from High or Low level Waveform 4 2.0 4.5 6.0 2.0 7.0
AC WAVEFORMS
For all waveforms, VM = 1.5V.
An, Bn
An, Bn VM VM VM VM
VM VM VM VM
Bn, An Bn, An
SF00773 SF00202
OEA OEA
VM VM VM VM
OEB OEB
tPZH tPLZ tPZL tPLZ
VOH –0.3V
VM VM
An, Bn An, Bn VOL +0.3V
0V
SF00775 SF00776
Waveform 3. 3-State Output Enable Time to High Level and Waveform 4. 3-State Output Enable Time to Low Level and
Output Disable Time from High Level Output Disable Time from Low Level
1990 Aug 30 6
Philips Semiconductors Product specification
Transceivers 74F242/74F243
VCC
tw AMP (V)
7.0V 90% 90%
NEGATIVE
RL VM VM
VIN VOUT PULSE
PULSE D.U.T. 10% 10%
0V
GENERATOR
tTHL (tf ) tTLH (tr )
RT CL RL
tTLH (tr ) tTHL (tf )
AMP (V)
90% 90%
POSITIVE
Test Circuit for 3-State Outputs PULSE VM VM
10% 10%
tw 0V
SWITCH POSITION
TEST SWITCH
tPLZ closed Input Pulse Definition
tPZL closed
All other open
DEFINITIONS:
RL = Load resistor;
see AC electrical characteristics for value. INPUT PULSE REQUIREMENTS
CL = Load capacitance includes jig and probe capacitance; family
see AC electrical characteristics for value. amplitude VM rep. rate tw tTLH tTHL
RT = Termination resistance should be equal to ZOUT of 2.5ns 2.5ns
74F 3.0V 1.5V 1MHz 500ns
pulse generators.
SF00777
1990 Aug 30 7
Philips Semiconductors Product specification
1990 Aug 30 8
Philips Semiconductors Product specification
SO14: plastic small outline package; 14 leads; body width 3.9 mm SOT108-1
1990 Aug 30 9
Philips Semiconductors Product specification
Objective Development This data sheet contains the design target or goal specifications for product development.
specification Specification may change in any manner without notice.
Preliminary Qualification This data sheet contains preliminary data, and supplementary data will be published at a later date.
specification Philips Semiconductors reserves the right to make chages at any time without notice in order to
improve design and supply the best possible product.
Product Production This data sheet contains final specifications. Philips Semiconductors reserves the right to make
specification changes at any time without notice in order to improve design and supply the best possible product.
[1] Please consult the most recently issued datasheet before initiating or completing a design.
Definitions
Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For
detailed information see the relevant data sheet or data handbook.
Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one
or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or
at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended
periods may affect device reliability.
Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips
Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or
modification.
Disclaimers
Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can
reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications
do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application.
Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard
cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no
responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these
products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless
otherwise specified.
yyyy mmm dd 10