Professional Documents
Culture Documents
576 1 80 cct-1
576 1 80 cct-1
PURETEC
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
100
KEY FEATURES
FEATURES
• Freedom from seizure when used with corrosive gases - gas does not come into contact with
the valve operating mechanism
• Positive and effective operation - valve spindle is mechanically linked to the operating
handwheel, which only requires low closing torque
• Long life - valve spindle and seat are replaceable
• Adjustable gland packing - in the unlikely event of a leakage occuring past the valve spindle,
when opening the valve, rectification is readily achieved by retightening the gland packing nut
• Low internal volume - this is particularly beneficial, when using the valve for hygroscopic,
corrosive or high purity gases, where inert gas purging may be necessary before opening or
after closing the valve
• Left hand threaded counter screw to secure sealing mechanism even under excessive torque
ST ANDARD SPECIFICA
STANDARD TION
SPECIFICATION
Working pressure pmax 200 bar/3000 psi
Temperature range -25°C up to + 65°C
Helium leak rate at pmax
• internal 10-6 mbarl/sec
• external 10-5 mbarl/sec
• safety 10-8 mbarl/sec
Flow coefficient Cv 0,3
Seat orifice size 3,3 mm
DESIGN VARIANT
VARIANT
OPTIONS
• Threading for flow restrictor
• Dip tube connection
• Valve body and handwheel PTFE coated
• Gas wetted components electrochemically polished
ORDERING
When ordering, please specify: Connections:
• Serial number or range A: outlet
• Type of gas C: inlet
• Connections F: flow restrictor
• Safety device specifications G: dip tube
• Options and special features
Body material
PTFE 25%GF PTFE Carbon filled AISI 303 Monel AISI 316L AlSiBz AISI 303 AISI 316L
AISI 303
AISI 316L
Brass
AlSiBz
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
150
KEY FEATURES
FEATURES
• 3 - piece sturdy stem design
• Non rotating, threadless lower spindle
• No particle shedding threading in gas wetted valve cavity
• Self centering Hastelloy© seal tip
• Adjustable gland packing - in the unlikely event of a leakage occuring past the valve spindle,
when opening the valve, rectification is readily achieved by retightening the gland packing nut
• Left hand threaded counter screw to secure sealing mechanism even under excessive torque
• O-rings fitted into the gland to exclude humidity
ST ANDARD SPECIFICA
STANDARD TION
SPECIFICATION
Working pressure pmax 150 bar/2175 psi
Temperature range -25°C up to + 65°C
Helium leak rate at pmax
• internal 10-5 mbarl/sec
• external 10-5 mbarl/sec
• safety 10-8 mbarl/sec
Flow coefficient Cv 1,1
Seat orifice size 6 mm
Ø 65 mm
DESIGN VARIANT
VARIANT
125 mm
OPTIONS
• Attachement for 24 mm key operation
• Threading for flow restrictor
• Dip tube connection
• Valve body and gland assembly PTFE - coated
Body material
AISI 303
AISI 316L
AlSiBz
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
160
KEY FEATURES
FEATURES
• 2 - piece sturdy stem design
• Non rotating, threadless lower spindle
• No particle shedding threading in gas wetted valve cavity
• Self adjusting, spring loaded V-ring gland packing
• Seft hand threaded counter screw to secure sealing mechanism even under excessive torque
• O-ring and nickel gasket fitted into the gland guarantee a secondary sealong and exclude humidity
• Soft seat offers low operating torque and is captivated to avoid extrusion and blomage of the valve
ST ANDARD SPECIFICA
STANDARD TION
SPECIFICATION
Working pressure pmax 200 bar/3000 psi
Temperature range -25°C up to + 65°C
Helium leak rate at pmax
• internal 10-6 mbarl/sec
• external 10-5 mbarl/sec
• safety 10-8 mbarl/sec
Flow coefficient Cv 1,1
Seat orifice size 6 mm
DESIGN VARIANT
VARIANT
SAFETY DEVICE
Metal seat
OPTIONS
• threading for flow restrictor
• dip tube connection
Body material
AISI 303
AISI 316L
St52-3
9SMn28
AlSiBz
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
161
KEY FEATURES
FEATURES
• 2 - piece sturdy stem design
• Non rotating, threadless lower spindle
• No particle shedding threading in gas wetted valve cavity
• Self adjusting, spring loaded V-ring gland packing
• Left hand threaded counter screw to secure sealing mechanism even under excessive torque
• O-ring and nickel gasket fitted into the gland guarantee a secondary sealong and exclude humidity
ST ANDARD SPECIFICA
STANDARD TION
SPECIFICATION
Working pressure pmax 200 bar/3000 psi
Temperature range -25°C up to + 65°C
Helium leak rate at pmax
• internal 10-6 mbarl/sec
• external 10-5 mbarl/sec
• safety 10-8 mbarl/sec
Flow coefficient Cv 1,1
Seat orifice size 6 mm
DESIGN VARIANT
VARIANT
OPTIONS
• Threading for flow restrictor
• Dip tube connection
• Valve spindle with shear off section to prevent overtorquing
AISI 303
AISI 316L
St52-3
9SMn28
AlSiBz
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
165
KEY FEATURES
FEATURES
• 2 - piece sturdy stem design
• Non rotating, threadless lower spindle
• No particle shedding threading in gas wetted valve cavity
• Adjustable gland packing - in the unlikely event of a leakage occuring past the valve spindle,
when opening the valve, rectification is readily achieved by retightening the gland packing nut
• Left hand threaded counter screw to secure sealing mechanism even under excessive torque
ST ANDARD SPECIFICA
STANDARD TION
SPECIFICATION
Working pressure pmax 200 bar/3000 psi
Temperature range -25°C up to + 65°C
Helium leak rate at pmax
• internal 10-5 mbarl/sec
• external 10-5 mbarl/sec
• safety 10-8 mbarl/sec
Flow coefficient Cv 1,1
Seat orifice size 6 mm
DESIGN VARIANT
VARIANT Ø 65 mm
128 mm
OPTIONS
• Threading for flow restrictor
• Key operation
• Dip tube connection
Body material
PTFE AISI 303 AISI 303 Monel AISI 303 AISI 316L Brass AlSiBz
gold-plated
AISI 303
AISI 316L
St52-3
9SMn28
Brass
AlSIBz
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
175
KEY FEATURES
FEATURES
• Highly corrosion-resistant AlSiBz body and Monel stem
• Designed for yoke connector application
• Valve design complies with US Chlorine Institute specifications
• Adjustable gland packing - in the unlikely event of a leakage occuring past the valve spindle,
when opening the valve, rectification is readily achieved by retightening the gland packing nut
ST ANDARD SPECIFICA
STANDARD TION
SPECIFICATION
Working pressure pmax 35 bar/500 psi
Temperature range -25°C up to + 65°C
Helium leak rate at pmax
• internal 10-4 mbarl/sec
• external 10-4 mbarl/sec
• safety 10-8 mbarl/sec
Flow coefficient Cv 0,75
Seat orifice size 5 mm
Material
• body A1SIBr
• stem monel ®
• packing PTFE
• body see below
08-8
CEODEUX
PURETEC
D 175
DESIGN VARIANT
VARIANT
OPTIONS
• Reseating set
• Various inlet and outlet connections and connection standards
SERIES D175 4
Body material
Body material
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
186
KEY FEATURES
FEATURES
• Adjustable gland packing - in the unlikely event of a leakage occuring past the valve spindle,
when opening the valve, rectification is readily achieved by retightening the gland packing nut
• Spindle threads not in gas wetted area
• Gland nut locked with hexagon nut
• Self centering seat offers low closing torques
ST ANDARD SPECIFICA
STANDARD TION
SPECIFICATION
Working pressure pmax 200 bar/3000 psi
Temperature range -25°C up to + 65°C
Helium leak rate at pmax
• internal 10-5 mbarl/sec
• external 10-5 mbarl/sec
Flow coefficient Cv 0,25
Seat orifice size 3 mm
OPTIONS
• Threading for flow restrictor
• Dip tube and/ or dip tube connection
ORDERING
When ordering, please specify: Connections:
• Serial number or range A outlet
• Type of gas C inlet
• Connections F flow restrictor
• Options and special features G dip tube
Body material
PTFE AISI 303 Monel AISI 316L AISI 316 Monel AISI 316L
gold plated
AISI 303
AISI 316L
AISiBz
Brass
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
200
KEY FEATURES
FEATURES
• Soft seat sealing arrangement offers low operating torque
• Valve seat captivated to avoid extrusion and blockage of the valve
• High leak tightness integrity through diaphragm sealing
• High performance thrust pad
STANDARD SPECIFICA
STANDARD TION
SPECIFICATION
Working pressure pmax 200 bar/3000 psi
Temperature range -25°C up to+ 65°C
Helium leak rate at pmax
•internal 10-7 mbarl/sec
•external 10-7 mbarl/sec
•safety 10-8 mbarl/sec
Flow coefficient Cv 0,35
Seat orifice size 3,5 mm
DESIGN VARIANT
VARIANT
OPTIONS
• Chrome or nickel plating, for brass valves
• Alternative seat disc materials: PCTFE, PI (Vespel®), Connections:
PA 6.6 (Nylon®) A outlet
C inlet
ORDERING
When ordering, please specify:
• Serial number or range
• Type of gas
• Connections
• Safety device specifications
• Options and special features
Body material
Hastelloy® Nickel AISI 303 AISI 316L Brass Nickel PCTFE PI (Vespel®) PA 6,6
AISI 303
AISI 303
AISI 316L
AISI 316L
BRASS
BRASS
BRASS
Nickel
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
201
KEY FEATURES
FEATURES
• All metal seal, no contamination
• High leak tightness integrity through diaphragm sealing
• High performance thrust pad
STANDARD SPECIFICA
STANDARD TION
SPECIFICATION
Working pressure pmax 200 bar/3000 psi
Temperature range -25°C up to + 65°C
Helium leak rate at pmax
• internal 10-7 mbarl/sec
• external 10-7 mbarl/sec
• safety 10-8 mbarl/sec
Flow coefficient Cv 0,25
Seat orifice size 3,5 mm
DESIGN VARIANT
VARIANT
OPTIONS
• Chrome or nickel plating, for brass valves
• Gas wetted components electrochemically polished Connections:
• Clean room assembling A outlet
ORDERING
When ordering, please specify:
• Serial number or range
• Type of gas
• Connections
• Safety device specifications
• Options and special features
Body material
AISI 303
AISI 316L
Brass
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
265
KEY FEATURES
FEATURES
• Dual port design to withdraw liquid or vapour
• Easy withdrawal of liquefied gas by pressurising through vapour port
• Quick filling of liquefied gas by releasing cylinder head pressure through additional vapour port
• Eliminates need for 2-valve system on certain containers reducing leak risk potentional and cost of
ownership
• Soft seat sealing arrangement offers low operating torque
• Valve seat captivated to avoid extrusion and blockage of the valve
STANDARD SPECIFICA
STANDARD TION
SPECIFICATION
Working pressure pmax 200 bar/3000 psi
Temperature range -25°C up to + 65°C
Helium leak rate at pmax
• internal 10-7 mbarl/sec
• external 10-7 mbarl/sec
• safety 10-8 mbarl/sec
Flow coefficient Cv 0,35
Seat orifice size 3,5 mm
DESIGN VARIANT
VARIANT
OPTIONS
• Chrome or nickel plating
• Alternative seat disc materials: Pa 6,6 (Nylon®), PCTFE, Connections:
PI (Vespel®) A, A1 outlets
• Clean room assembling
ORDERING
When ordering, please specify:
• Serial number or range
• Type of gas
• Connections
• Safety device specifications
• Options and special features
Body material
Hastelloy
®
Nickel AISI 303 AISI 316L Brass Nickel PCTFE PI (Vespel®) PA 6,6
AISI 303
AISI 303
AISI 316L
AISI 316L
BRASS
BRASS
BRASS
Nickel
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
266
KEY FEATURES
FEATURES
• All metal seal, no contamination
• Dual port design to withdraw liquid or vapour
• Easy withdrawal of liquefied gas by pressuring through vapour port
• Quick filling of liquefied gas by releasing cylinder head pressure through additional vapour port
• Eliminates need for 2-valve system on certain containers reducing leak risk potentional and
cost of ownership
ST ANDARD SPECIFICA
STANDARD TION
SPECIFICATION
Working pressure pmax 200 bar/3000 psi
Temperature range -25°C up to+ 65°C
Helium leak rate at pmax
• internal 10-7 mbarl/sec
• external 10-7 mbarl/sec
• safety 10-8 mbarl/sec
Flow coefficient Cv 0,25
Seat orifice size 3,5 mm
DESIGN VARIANT
VARIANT Pressure relief devices are in accordance with CGA S-1.1
Burst disc materials are nickel or AISI 316L
SAFETY DEVICE
OPTIONS
• Alternative body materials
• Chrome or nickel plating
• Gas wetted components
electrochemically polished
ORDERING Connections:
When ordering, please specify: A, A1 outlets
• Serial number or range C inlet
• Type of gas G dip tube
• Connections
• Safety device specifications
• Options and special features
Body material
Hastelloy ®
Nickel AISI 303 Nickel
AISI 303
AISI 316L
BRASS
Nickel
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
260
KEY FEATURES
FEATURES
• Dual port design to withdraw liquid or vapour
• Easy withdrawal of liquefied gas by pressurising through vapour port
• Quick filling of liquefied gas by releasing cylinder head pressure through additional vapour port
• Eliminates need for 2-valve system on certain containers reducing leak risk potentional and
cost of ownership
STANDARD SPECIFICA
STANDARD TION
SPECIFICATION
Working pressure pmax 45 bar/650 psi
Temperature range -25°C up to + 65°C
Helium leak rate at pmax
• internal 10-7 mbarl/sec
• external 10-7 mbarl/sec
• safety 10-8 mbarl/sec
Flow coefficient Cv 1,0
Seat orifice size 8 mm
DESIGN VARIANT
VARIANT Pressure relief devices are in accordance with CGA S-1.1
Burst disc materials are nickel or AISI 316L
SAFETY DEVICE
OPTIONS
• Alternative body materials
• Chrome or nickel plating
• Gas wetted components
electrochemically polished
ORDERING Connections:
A, A1 outlets
When ordering, please specify:
C inlet
• Serial number or range
G dip tube
• Type of gas
• Connections
• Safety device specifications
• Options and special features
Body material
Hastelloy ®
Nickel AISI 303 Nickel
AISI 303
AISI 316L
BRASS
Nickel
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
250
KEY FEATURES
FEATURES
• Valve seat captivated to avoid extrusion and blockage of the valve
• Easy operation under high pressure
• O-rings fitted into the gland to exclude penetration of humidity
STANDARD SPECIFICA
STANDARD TION
SPECIFICATION
Working pressure pmax 200 bar/3000 psi
Temperature range -25°C up to + 65°C
Helium leak rate at pmax
• internal 10-7 mbarl/sec
• external 10-7 mbarl/sec
Flow coefficient Cv 0,25
Seat orifice size 4 mm
DESIGN VARIANT
VARIANT
OPTIONS
• Alternative body materials
• Alternative seat disc materials: PA 6,6 (Nylon®), PCTFE, PI (Vespel®)
• Threading for flow restrictor
Body material
Hastelloy ®
AISI 303 AISI 316L Brass Al SI Br PCTFE PI (Vespel®) Pa 6,6
AISI 303
AISI 303
AISI 316L
AISI 316L
BRASS
BRASS
BRASS
Al Si Br
Al Si Br
Al Si Br
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
251
KEY FEATURES
FEATURES
• All metal seal, no contamination
• Easy operation under high pressure
• O-rings fitted into the gland to exclude penetration of humidity
STANDARD SPECIFICA
STANDARD TION
SPECIFICATION
Working pressure pmax 200 bar/3000 psi
Temperature range -25°C up to + 65°C
Helium leak rate at pmax
• internal 10-7 mbarl/sec
• external 10-7 mbarl/sec
Flow coefficient Cv 0,2
Seat orifice size 2,5 mm
DESIGN VARIANT
VARIANT
OPTIONS
• Alternative body materials
• Threading for flow restrictor
• Dip tube connection
Body material
Hastelloy ®
AISI 303 Nickel
AISI 303
AISI 316L
BRASS
Al SI Br
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
300
KEY FEATURES
FEATURES
• Reduced dead spaces and gas wetted volumes allow easy purging process
• Freedom of internal threads and springs insures minimum particulate generation
• Very low internal volume with minimum dead spaces. This is particularly beneficial, when using
the valve for hygroscopic, corrosive, pyrophoric or high purity gases where inert gas purging is
necessary before opening or after closing the valve
• Freedom from seizure when used with corrosive gases. Gas does not come into contact with
the valve operating mechanism
• Positive and effective operation, valve lower spindle is mechanically linked to the upper
spindle and operating handwheel
• Backed up welded diaphragms provide a permanent and durable gas tight seal
STANDARD SPECIFICA
STANDARD TION
SPECIFICATION
Working pressure pmax 200 bar/3000 psi
Temperature range -25°C up to + 65°C
Helium leak rate at pmax
• internal 10-8 mbarl/sec
• external 10-8 mbarl/sec
• safety 10-8 mbarl/sec
Flow coefficient Cv 0,25
Seat orifice size 4 mm
Material
DESIGN VARIANT
VARIANT
OPTIONS
• Alternative body materials
and seat disc materials: PVDF, PI (Vespel®), PCTFE
• Gas wetted components electrochemically polished Connections:
ORDERING
When ordering, please specify:
• Serial number or range
• Type of gas
• Connections
• Safety device specifications
• Options and special features
Body material
Hastelloy® Nickel AISI 316L Hastelloy® Nickel PCTFE PVDF PI (Vespel®) AISI 316L Nickel
AISI 316L
AISI 316L
AISI 316L
Hastelloy®
Hastelloy®
Nickel
Nickel
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
330
KEY FEATURES
FEATURES
• Reduced dead spaces and gas wetted volumes allow easy purging process
• Freedom of internal threads and springs insures minimum particulate generation
• Very low internal volume with minimum dead spaces. This is particularly beneficial, when using
the valve for hygroscopic, corrosive, pyrophoric or high purity gases where inert gas purging is
necessary before opening or after closing the valve
• Freedom from seizure where used with corrosive gases. Gas does not come into contact with
the valve operating mechanism
• Positive and effective operation, valve lower spindle is mechanically linked to the upper
spindle and the operating handwheel
• Backed up welded diaphragms provide a permanent and durable gas tight seal
• O-Rings in the gland and on spindle guarantee a secondary sealing
• threaded vent hole
STANDARD SPECIFICA
STANDARD TION
SPECIFICATION
Working pressure pmax 200 bar/3000 psi
Temperature range -25°C up to + 65°C
Helium leak rate at pmax
• internal 10-8 mbarl/sec
• external 10-8 mbarl/sec
• safety 10-8 mbarl/sec
Flow coefficient Cv 0,35
Seat orifice size 4 mm
DESIGN VARIANT
VARIANT
OPTIONS
• Alternative body materials and seat disc
materials: PVDF, PCTFE, PI (Vespel ®)
• Gas wetted components
electrochemically polished Connections:
ORDERING
When ordering, please specify:
• Serial number or range
• Body material
• Type of gas
• Connections
• Safety device specifications
• Options and special features
Body material
Body material
Hastelloy® Nickel AISI 316L Hastelloy® Nickel PCTFE PVDF PI (Vespel®) AISI 316L Nickel
AISI 316L
AISI 316L
AISI 316L
Hastelloy®
Hastelloy®
Hastelloy®
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
340
KEY FEATURES
FEATURES
• Dual port design to withdraw liquid or vapour
• Easy withdrawal of liquefied gas by pressurising through vapour port
• Quick filling of liquefied gas by releasing cylinder head pressure through additional vapour port
• Eliminates need for 2-valve system on certain containers reducing leak risk potentional and
cost of ownership
• Threaded vent hole
STANDARD SPECIFICA
STANDARD TION
SPECIFICATION
Working pressure pmax 200 bar/3000 psi
Temperature range -25°C up to + 65°C
Helium leak rate at pmax
• internal 10-8 mbarl/sec
• external 10-8mbarl/sec
• safety 10-8 mbarl/sec
Flow coefficient Cv 0,35
Seat orifice size 4 mm
DESIGN VARIANT Pressure relief devices are in accordance with CGA S-1.1
VARIANT
Burst disc materials are nickel or AISI 316L
SAFETY DEVICE
OPTIONS Connections:
• Alternative body materials: Nickel, Hastelloy® A, A1 outlets
and seat disc materials: PVDF, PI (Vespel ®), PCTFE C inlet
• Various inlet and outlet connections and connection G dip tube
standards, including CGA 630/710
ORDERING
When ordering, please specify:
• Serial number or range
• Type of gas
• Connections
• Safety device specifications
• Options and special features
Hastelloy® Nickel AISI 316L Hastelloy® Nickel PCTFE PVDF PI (Vespel®) AISI 316L Nickel
AISI 316L
AISI 316L
AISI 316L
Hastelloy®
Hastelloy®
Nickel
Nickel
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
341
KEY FEATURES
FEATURES
• All metal seal, no contamination
• Dual port design to withdraw liquid or vapour
• Easy withdrawal of liquefied gas by pressurising through vapour port
• Quick filling of liquefied gas by releasing cylinder head pressure through additional vapour port
• Eliminates need for 2-valve system on certain containers reducing leak risk potentional and
cost of ownership
STANDARD SPECIFICA
STANDARD TION
SPECIFICATION
Working pressure pmax 200 bar/3000 psi
Temperature range -25°C up to + 65°C
Helium leak rate at pmax
• internal 10-8 mbarl/sec
• external 10-8 mbarl/sec
• safety 10-8 mbarl/sec
Flow coefficient Cv 0,3
Seat orifice size 4 mm
DESIGN VARIANT Pressure relief devices are in accordance with CGA S-1.1
VARIANT
Burst disc materials are nickel or AISI 316L
SAFETY DEVICE
OPTIONS
• Alternative body materials: Nickel, Hastelloy®
and seat disc materials: PVDF, PI (Vespel ®), PCTFE
• Various inlet and outlet connections and connection
standards, including CGA 630/710
ORDERING
When ordering, please specify:
• Serial number or range
• Type of gas
• Connections
• Safety device specifications
• Options and special features
AISI 316L
Hastelloy®
Nickel
Monel
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
342
KEY FEATURES
FEATURES
• Dual port design to withdraw liquid or vapour
• Easy withdrawal of liquefied gas by pressurising through vapour port
• Quick filling of liquefied gas by releasing cylinder head pressure through additional vapour port
• Eliminates need for 2-valve system on certain containers reducing leak risk potentional and
cost of ownership
STANDARD SPECIFICA
STANDARD TION
SPECIFICATION
Working pressure pmax 45 bar/ 650 psi
Temperature range -25°C up to +65 °C
Helium leak rate at pmax
• internal 10-8 mbarl/sec
• external 10-8 mbarl/sec
• safety 10-8 mbarl/sec
Flow coefficient Cv 0,7
Seat orifice size 8 mm
DESIGN VARIANT Pressure relief devices are in accordance with CGA S-1.1
VARIANT
Burst disc materials are nickel or AISI 316L
SAFETY DEVICE
OPTIONS
• Alternative body materials: Nickel, Hastelloy®
and seat disc materials: PVDF, PI (Vespel ®), PCTFE
• Various inlet and outlet connections and connection
standards, including CGA 630/710
ORDERING
When ordering, please specify:
• Serial number or range
• Type of gas
• Connections
• Safety device specifications
• Options and special features
Hastelloy® Nickel AISI 316L Hastelloy® Nickel PCTFE PVDF PI (Vespel®) AISI 316L Nickel
AISI 316L
AISI 316L
AISI 316L
Hastelloy®
Hastelloy®
Nickel
Nickel
Monel
Monel
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
395
KEY FEATURES
FEATURES
• Dual port design to withdraw liquid or vapour
• Easy withdrawal of liquefied gas by pressurising through vapour port
• Quick filling of liquefied gas by releasing cylinder head pressure through additional vapour port
• Eliminates need for 2-valve system on certain containers reducing leak risk potentional and
cost of ownership
ST ANDARD SPECIFICA
STANDARD TION
SPECIFICATION
Working pressure pmax 200 bar/3000 psi
Temperature range -25°C up to +65°C
Helium leak rate at pmax
• internal 10-8 mbarl/sec
• external 10-8 mbarl/sec
• safety 10-8 mbarl/sec
Flow coefficient Cv 0,25
Seat orifice size 4 mm
DESIGN VARIANT Pressure relief devices are in accordance with CGA S-1.1
VARIANT Ø 65 mm
Burst disc materials are nickel or AISI 316L
SAFETY DEVICE
135 mm
OPTIONS
• Alternative body materials: Nickel, Hastelloy®
and seat disc materials: PVDF, PI (Vespel ®), PCTFE
• Various inlet and outlet connections and connection
standards, including CGA 630/710
ORDERING
When ordering, please specify:
• Serial number or range
• Type of gas
• Connections
• Safety device specifications
• Options and special features
Body material
Hastelloy® Nickel AISI 316L Hastelloy® Nickel PCTFE PVDF PI (Vespel®) AISI 316L Nickel
AISI 316L
AISI 316L
AISI 316L
Hastelloy®
Hastelloy®
Nickel
Nickel
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
390
KEY FEATURES
FEATURES
• Reduced dead spaces and gas wetted volumes allow easy purging process
• Freedom of internal threads and springs insures minimum particulate generation
• Very low internal volume with minimum dead spaces. This is particularly beneficial, when using
the valve for hygroscopic, corrosive, pyrophoric or high purity gases where inert gas purging is
necessary before opening or after closing the valve
• Freedom from seizure when used with corrosive gases. Gas does not come into contact with
the valve operating mechanism
• Positive and effective operation, valve lower spindle is mechanically linked to the upper
spindle and the operating handwheel
• Backed up welded diaphragms provide a permanent and durable gas tight seal
• Burst disc materials are nickel or AISI 316L
STANDARD SPECIFICA
STANDARD TION
SPECIFICATION
Working pressure pmax 200 bar/3000 psi
Temperature range -25°C up to +65°C
Helium leak rate at pmax
• internal 10-8 mbarl/sec
• external 10-8 mbarl/sec
• safety 10-8 mbarl/sec
Flow coefficient Cv 0,25
Seat orifice size 4 mm
DESIGN VARIANT
VARIANT Connections:
A outlet
C inlet
F flow restrictor
G dip tube
OPTIONS
• Alternative body materials and seat disc materials:
PVDF, PI Vespel ®
• Gas wetted components electrochemically polished
• Clean room assembling
ORDERING
When ordering, please specify:
• Serial number or range
• Body material
• Type of gas
• Connections
• Safety device specifications
• Options and special features
Body material
Body material
Hastelloy® Nickel AISI 316L Hastelloy® PCTFE PVDF PI (Vespel®) AISI 316L Nickel
AISI 316L
AISI 316L
AISI 316L
Hastelloy®
Hastelloy®
Hastelloy®
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
350
KEY FEATURES
FEATURES
• Reduced dead spaces and gas wetted volumes allow easy purging process
• Freedom of internal threads and springs insures minimum particulate generation
• very low internal volume with minimum dead spaces. This is particularly beneficial, when using
the valve for hygroscopic, corrosive, pyrophoric or high purity gases where inert gas purging is
necessary before opening or after closing the valve
• Freedom from seizure when used with corrosive gases. Gas does not come into contact with
the valve operating mechanism
• Positive and effective operation, valve lower spindle is mechanically linked to the upper
spindle and the operating handwheel
• Backed up welded diaphragms provide a permanent and durable gas tight seal
• Safe and easy acting operation system including manual override device: the valve can be
locked in the closed position by manual operation of the handwheel. This is an important
safety feature especially during transportation
• In the closed position the valve fits under all standard valve protection caps
STANDARD SPECIFICA
STANDARD TION
SPECIFICATION
Working pressure pmax 165 bar/2400 psi
Pneum. act. press. min 5, max 10 bar
Temperature range -25°C up to +65°C
Helium leak rate at pmax
• internal 10-8 mbarl/sec
• external 10-8 mbarl/sec
• safety 10-8 mbarl/sec
Flow coefficient Cv 0,25
Seat orifice size 4 mm
DESIGN VARIANT
VARIANT Connections:
A outlet
C inlet
F flow restrictor
G dip tube
OPTIONS
• Alternative body materials and seat disc materials: PVDF, PCTFE, PI (Vespel®)
• Gas wetted components electrochemically polished
• Clean room assembling
• Cleaning for UHP / ECD applications
ORDERING
When ordering, please specify:
• Serial number or range
• Body material
• Type of gas
• Connections
• Safety device specifications
• Options and special features
Body material
Hastelloy® Nickel AISI 316L Hastelloy® Nickel PCTFE PVDF PI (Vespel®) AISI 316L Nickel
AISI 316L
AISI 316L
AISI 316L
Hastelloy®
Hastelloy®
Nickel
Nickel
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
D Constant flow
cylinder valve
405
KEY FEATURES
FEATURES
• O-Ring seal provides durability for multiple use calibration applications
• Compact, light weight design ideal for portability
• Cylinder valve, pressure regulator and fill adapter - entire delivery system available from one supplier.
STANDARD SPECIFICA
STANDARD TION
SPECIFICATION
Working pressure max. 600*/3000 psi
Helium leak rate 1 x 10-4 cc/sec
Temperature range -5°F to 140°F
max pressure for Aluminum
Wetted materials
• Body stainless steel, brass,
nickel plated brass,
aluminum
• Valve seat/seal FPM
• O-ring FPM
• Internal parts stainless steel
05-2
CEODEUX
PURETEC
D 405
DESIGN VARIANT
VARIANT
BASIC MODELS
• Inlet connections: 3/4" - 16 UNF, 1" - 14 UNF
• Outlet connections: 5/8" - 18UNF
ORDERING
When ordering, please specify:
• Series number or range
• Connections
• Type of gas
• Safety device specifications
• Options and special features
OPTIONS
• Safety device acc. to CGA S1.1
• Choice of o-ring materials: EPDM
www
rotarex.com
IS
ISOO 9001
CERTIFIED
24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: *352 32 78 32 - 322
CEODEUX
PURETEC
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
750
KEY FEATURES
FEATURES
• Integrated electronic liquid level measuring device
• Whole system resistant to vibrations
• High leak tightness integrity trough diaphragm sealing
• High performance thrust pad
STANDARD SPECIFICA
STANDARD TION
SPECIFICATION
Working pressure pmax 200 bar/3000 psi
Temperature range -25°C up to +65°C
Helium leak rate at pmax
• internal 10-7 mbarl/sec
• external 10-7 mbarl/sec
• safety 10-8 mbarl/sec
Flow coefficient Cv 0,25
Seat orifice size 3,5 mm / 0.138"
DESIGN VARIANT
VARIANT
OPTIONS ORDERING
• Chrome or nickel plating, for brass valves When ordering, please specify:
• Gas wetted components electrochemically polished • Serial number or range
• Clean room assembling • Type of gas
• Cleaning for UHP/ECD applications • Connections
Body material
Hastelloy ®
AISI 303 Nickel Brass AISI 303 AISI 316L PCTFE
AISI 303
AISI 316L
Brass
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
751
KEY FEATURES
FEATURES
• Integrated electronic liquid level measuring device
• Soft seat sealing arrangement offers low operating torque
• Whole system resistant to vibrations
• Valve seat captivated to avoid extrusion and blockage of the valve
• High leak tightness integrity trough diaphragm sealing
• High performance thrust pad
STANDARD SPECIFICA
STANDARD TION
SPECIFICATION
Working pressure pmax 200 bar/3000 psi
Temperature range -25°C up to +65°C /
Helium leak rate at pmax
• internal 10-7 mbarl/sec
• external 10-7 mbarl/sec
• safety 10-8 mbarl/sec
Flow coefficient Cv 0,35
Seat orifice size 3,5 mm / 0.138"
DESIGN VARIANT
VARIANT
OPTIONS
• Chrome or nickel plating, for brass valves
• Alternative seat disc materials: PCTFE, PI (Vespel ®), PA 6.6 (Nylon®)
• Gas wetted components electrochemically polished
• Clean room assembling
• Cleaning for UHP/ECD applications
ORDERING
When ordering, please specify:
• Serial number or range
• Type of gas
• Connections
• Safety device specifications
• Options and special features
Body material
Hastelloy® AISI 303 AISI 316L Brass Nickel PCTFE AISI 303 AISI 316L Brass PCTFE
AISI 303
AISI 316L
Brass
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
High flow cylinder valves, tied diaphragm seal type, for ultra
high purity corrosive gases
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
335
KEY FEATURES
FEATURES
• Reduced dead spaces and gas wetted volumes allow easy purging process
• Freedom of internal threads and springs insures minimum particulate generation
• Very low internal volume with minimum dead spaces. This is particularly beneficial, when using
the valve for hygroscopic, corrosive, pyrophoric or high purity gases where inert gas purging is
necessary before opening or after closing the valve
• Freedom from seizure where used with corrosive gases. Gas does not come into contact with
the valve operating mechanism
• Positive and effective operation, valve lower spindle is mechanically linked to the upper
spindle and the operating handwheel
• Backed up welded diaphragms provide a permanent and durable gas tight seal
• O-Rings in the gland and on spindle guarantee a secondary sealing
• Threaded vent hole
STANDARD SPECIFICA
STANDARD TION
SPECIFICATION
Working pressure pmax 200 bar/3000psi
Temperature range -40oC up to +70oC
Helium leak rate at pmax
• internal 10-8 mbarl/sec
• external 10-8 mbarl/sec
• safety 10-8 mbarl/sec
Flow coefficient Cv 0,35
Seat orifice size 4 mm
DESIGN VARIANT
VARIANT Connection
A outlet
C inlet
F flow restrictor
G dip tube
OPTIONS ORDERING
• Alternative body materials When ordering, please specify:
and seat disc materials: PVDF, PCTFE, • Serial number or range
PI (Vespel ®) • Body material
• Gas wetted components • Type of gas
Hastelloy® Nickel AISI 316L Hastelloy® Nickel PCTFE PVDF PI (Vespel®) AISI 316L Nickel
AISI 316L
AISI 316L
AISI 316L
Hastelloy®
Hastelloy®
Nickel
Nickel
Monel
Monel
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
336
KEY FEATURES
FEATURES
• All metal seal, no contamination
• Reduced dead spaces and gas wetted volumes allow easy purging process
• Freedom of internal threads and springs insures minimum particulate generation
• Very low internal volume with minimum dead spaces. This is particularly beneficial, when using
the valve for hygroscopic, corrosive, pyrophoric or high purity gases where inert gas purging is
necessary before opening or after closing the valve
• Freedom from seizure where used with corrosive gases. Gas does not come into contact with
the valve operating mechanism
• Positive and effective operation, valve lower spindle is mechanically linked to the upper
spindle and the operating handwheel
• Backed up welded diaphragms provide a permanent and durable gas tight seal
• O-Rings in the gland and on spindle guarantee a secondary sealing
• Threaded vent hole
STANDARD SPECIFICA
STANDARD TION
SPECIFICATION
Working pressure pmax 200 bar/3000psi
Temperature range -40oC up to +70oC
Helium leak rate at pmax
• internal 10-8 mbarl/sec
• external 10-8 mbarl/sec
• safety 10-8 mbarl/sec
Flow coefficient Cv 0,3
Seat orifice size 4 mm
DESIGN VARIANT
VARIANT Connection
A outlet
C inlet
F flow restrictor
G dip tube
OPTIONS ORDERING
• Alternativ body materials When ordering, please specify:
• Gas wetted components • Serial number or range
electrochemically polished • Body material
AISI 316L
Hastelloy®
Nickel
Monel
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
337
KEY FEATURES
FEATURES
• Reduced dead spaces and gas wetted volumes allow easy purging process
• Freedom of internal threads and springs insures minimum particulate generation
• Very low internal volume with minimum dead spaces. This is particularly beneficial, when using
the valve for hygroscopic, corrosive, pyrophoric or high purity gases where inert gas purging is
necessary before opening or after closing the valve
• Freedom from seizure where used with corrosive gases. Gas does not come into contact with
the valve operating mechanism
• Positive and effective operation, valve lower spindle is mechanically linked to the upper
spindle and the operating handwheel
• Backed up welded diaphragms provide a permanent and durable gas tight seal
• O-Rings in the gland and on spindle guarantee a secondary sealing
• Threaded vent hole
STANDARD SPECIFICA
STANDARD TION
SPECIFICATION
Working pressure pmax 45 bar/650 psi
Temperature range -40oC up to +70oC
Helium leak rate at pmax
• internal 10-8 mbarl/sec
• external 10-8 mbarl/sec
• safety 10-8 mbarl/sec
Flow coefficient Cv 0,7
Seat orifice size 8 mm
DESIGN VARIANT
VARIANT Connection
A outlet
C inlet
F flow restrictor
G dip tube
OPTIONS ORDERING
• Alternative body materials When ordering, please specify:
and seat disc materials: PVDF, PCTFE, • Serial number or range
PI (Vespel ®) • Body material
Hastelloy® Nickel AISI 316L Hastelloy® Nickel PCTFE PVDF PI (Vespel®) AISI 316L Nickel
AISI 316L
AISI 316L
AISI 316L
Hastelloy®
Hastelloy®
Nickel
Nickel
Monel
Monel
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
195
KEY FEATURES
FEATURES
• Dual port design to withdraw liquid or vapour
• Easy withdrawal of liquefied gas by pressurising through vapour port
• Quick filling of liquefied gas by releasing cylinder head pressure through additional vapour port
• Eliminates need for 2-valve system on certain containers reducing leak risk potential and cost of
ownership
ST ANDARD SPECIFICA
STANDARD TION
SPECIFICATION
Working pressure pmax 200 bar/3000 psi
Temperature range -25°C up to +65°C
Helium leak rate at pmax
• internal 10-6 mbarl/sec
• external 10-5 mbarl/sec
• safety 10-8 mbarl/sec
Flow coefficient Cv 1
Seat orifice size 6 mm
DESIGN VARIANT
VARIANT
SAFETY DEVICE
OPTIONS
Connections:
• Threading for flow restrictor
A, A1 outlets
• Dip tube connection
C inlet
• Alternative body material: carbon steel
F, F1 flow restrictor
ORDERING
When ordering, please specify:
• Serial number or range
• Type of gas
• Connections
• Safety device specifications
• Options and special features
AISI 303
AISI 316L
11SMn30
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
131
KEY FEATURES
FEATURES
• Freedom from seizure when used with corrosive gases - gas does not come into contact with the
valve operating mechanism
• Positive and effective operation - valve spindle is mechanically linked to the pneumatic actuator
• Long life - valve spindle and seat are replaceable
• Adjustable gland packing - in the unlikely event of a leakage occuring past the valve spindle, when
opening the valve, rectification is readily achieved by tightening the gland packing nut
• Low internal volume - this is particularly beneficial, when using the valve for hygroscopic corrosive or
high purity gases, where inert gas purging may be necessary before opening or after closing the valve
• In the closed position, the valve fits under most standard valve protection caps
• The air actuator is fitted with a quick connector. It is locked in place by the manual override
• The valve is held closed by the spring, in addition for safety reasons, it can be locked in the closed
position by the manual override
• By applying air pressure to the piston, the valve opens
• Retightening of the packing can be done with the air actuator in place
STANDARD SPECIFICA
STANDARD TION
SPECIFICATION
Working pressure pmax 200 bar/3000 psi
Pneum. act. press. 5 bar min.
Temperature range -25°C up to +65°C
Helium leak rate at pmax
• internal 10-5 mbarl/sec
• external 10-5 mbarl/sec
• safety 10-8 mbarl/sec
Flow coefficient Cv 0,25
Seat orifice size 2,8 mm
DESIGN VARIANT
VARIANT
OPTIONS
• Threading for flow restrictor
• Dip tube connection
• Gas wetted components electrochemically polished
• Clean room assembling
ORDERING
When ordering, please specify:
• Serial number or range Connections:
• Type of gas A: outlet
• Connections C: inlet
• Safety device specifications F: flow restrictor
• Options and special features G: dip tube
Body material
PTFE 25%GF PTFE Carbon filled AISI 303 AISI 316L AISI 316L AISI 303 AISI 316L
gold plated gold plated
AISI 303
AISI 316L
Brass
AlSiBz
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
158
KEY FEATURES
FEATURES
• high Cv 2,8 , 12mm orifice
• Removable seat
• 2 - piece sturdy stem design
• Non rotating, threadless lower spindle
• No particle shedding threading in gas wetted valve cavity
• Self adjusting, spring loaded V-ring gland packing
• Left hand threaded counter screw to secure sealing mechanism even under excessive torque
• O-ring gasket fitted into the packing support and the gland guarantee a secondary sealing and
exclude humidity
• Soft seat offers low operating torque and is captivated to avoid extrusion and blomage of the valve
STANDARD SPECIFICA
STANDARD TION
SPECIFICATION
Working pressure pmax 200 bar/3000 psi
Temperature range -25°C up to +65°C
Helium leak rate at pmax
• internal 10-5 mbarl/s
• external 10-5 mbarl/s
Flow coefficient Cv 2.8
Seat orifice size 12 mm
DESIGN VARIANT
VARIANT 77
OPTIONS
• Dip tube connection
• Alternative seat disc materials: PCTFE and PVDF ( KYNAR® )
163
• Valve spindle with shear off section to prevent overtorquing
• RPV
SERIES D158 1
Body material AlSI 316Ti
AISI 316Ti
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
159
KEY FEATURES
FEATURES
• high Cv 3 , 12mm orifice
• Removable seat
• 2 - piece sturdy stem design
• Non rotating, threadless lower spindle
• No particle shedding threading in gas wetted valve cavity
• Self adjusting, spring loaded V-ring gland packing
• Left hand threaded counter screw to secure sealing mechanism even under excessive torque
• O-ring gasket fitted into the packing support and the gland guarantee a secondary sealing and
exclude humidity
• Soft seat offers low operating torque and is captivated to avoid extrusion and blomage of the valve
STANDARD SPECIFICA
STANDARD TION
SPECIFICATION
Working pressure pmax 200 bar/3000 psi
Temperature range -25°C up to +65°C
Helium leak rate at pmax
• internal 10-5 mbarl/s
• external 10-5 mbarl/s
Flow coefficient Cv 3
Seat orifice size 12 mm
DESIGN VARIANT
VARIANT
Pressure relief devices are in accordance with CGA S-1.1
Burst disc materials are nickel or AISI 316L
140
OPTIONS
72
• Dip tube connection
• Alternative seat disc materials: PCTFE and PVDF ( KYNAR® )
SERIES D159 1
Body material AlSI 316Ti
AISI 303
AISI 316Ti
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
183
KEY FEATURES
FEATURES
• Double reversed seat design offers high level of security
• Primary soft seat to guarantee low sealing forces and an high leak integrity
• Second seat to ensure tightness if top valve destroyed
• 2-piece sturdy stem design
• Non-rotating, thread less lower spindle
• No particle shedding threading in gas wetted valve cavity
• Self-adjusting, spring-loaded V-ring gland packing
• O-ring fitted into gland nut guarantees a secondary sealing and exclude humidity
• Tamper proof by a special nut
STANDARD SPECIFICA
STANDARD TION
SPECIFICATION
Working pressure: 200bar/3000psi
T° range: -25°C up to +65°c
Helium leak rate
•Internal 10-5 mbar l /sec
•External 10-5 mbar l/sec
•Piston 10-3 mbar l/sec
Flow coefficient Cv 1,15
Seat orifice 12 mm
Gas wetted material: see table
08-8
CEODEUX
PURETEC
D 183
DESIGN VARIANT
VARIANT
• Inlet protection connection device
• Flange
• Forged body
146
OPTIONS
• Threading for floor restrictor
• Dip tube connection
• Alternative seat material: PCTFE / PVDF
• Valve spindle with share off section to prevent over torque
• Open/Close indicator
88
• type of gas
sssssssss
• connections
• safety device specifications
• options and special features
SERIES D183
Body material AlSI 316 Ti
AISI 316 Ti PTFE AISI 316 L PCTFE Monel 500K PTFE AISI 316 Ti
PVDF AISI 316 Ti PFA
AISI 316 Ti 1.4310 AISI 316 L AISI 316 L AISI 316 L FEP
PTFE
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
252
KEY FEATURES
• Soft seat sealing offers low operating torque
• Valve seat captivated to avoid extrusion and blockage of the valve
• O-ring fitted into the gland to exclude penetration of humidity
STANDARD SPECIFICATION
Working pressure pmax 200 bar/3000 psi
Temperature range -25 °C up to +65 °C
Helium leak rate at p max
• internal 10-7 mbarl/sec
• external 10-7 mbarl/sec
• safety 10-7 mbarl/sec
Flow coefficient Cv 0,25
Seat orifice size 4 mm
DESIGN VARIANT
Drawing=D 195 Pressure relief devices are in accordance with CGA S-1.1,
EN ISO 4126 or other national standards
Burst disc materials are nickel or AISI 316L
Safety device
OPTIONS
• Chrome or nickel plating for brass valves
• Alternative body materials and seat disc materials: PCTFE, PI, PA6.6
• Dip tube connections
• Flow restrictor threading
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
225
KEY FEATURES
FEATURES
• Soft seat sealing offers low operating torque
• Valve seat captivated to avoid extrusion and blockage of the valve
• High leak tightness integrity through diaphragm sealing
• High performance thrust with ball
• Open / close indicator
ST ANDARD SPECIFICA
STANDARD TION
SPECIFICATION
Working pressure pmax 200 bar for Europa /5500 psi for USA
Temperature range -25°C up to +65°C
Helium leak rate at pmax
• internal 10-7 mbarl/sec
• external 10-7 mbarl/sec
• safety 10-7 mbarl/sec
Flow coefficient Cv ????????????
Seat orifice size 3,5 mm
DESIGN VARIANT
VARIANT
OPTIONS
• Chrome or nickel plating for brass valves
• Alternative body materials and seat disc materials: PCTFE, PI, PA6.6
• Gas wetted components electrochemically polished
• Clean room assembling
• Ceaning for UHP / ECD applications
ORDERING
When ordering, please specify :
)
$
• Serial number or range
• Body material
• Type of gas
• Connections
• Safety device specifications
• Options and special features
*
&
GAS WETTED MATERIALS
MATERIALS
AISI 303
AISI 303
AISI 316L
AISI 316L
BRASS
BRASS
BRASS
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
240
KEY FEATURES
FEATURES
• Diaphragm direct seal type
• Valve seat captivated to avoid extrusion and blockage of the valve
• High leak tightness integrity through diaphragm sealing
• High performance thrust with ball
• Low internal volume with minimum dead spaces
• Pneumatically actuated version see SERIES D290
ST ANDARD SPECIFICA
STANDARD TION
SPECIFICATION
Working pressure pmax 200 bar/3000 psi
Temperature range -40 °C up to + 65 °C
Helium leak rate at pmax
• internal 10-8 mbarl/sec
• external 10-8 mbarl/sec
• safety 10-8 mbarl/sec
Flow coefficient Cv 0,3
Seat orifice size 4 mm
DESIGN VARIANT
VARIANT
• Cleaning for UHP / ECD applications
• Dip tube connections
• Flow restrictor threading
$
ORDERING
When ordering, please specify :
• Serial number or range
• Type of gas
• Connections
• Safety device specifications *
• Options and special features &
AISI 316L
AISI 316L
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
290
KEY FEATURES
FEATURES
• Diaphragm direct seal type
• Valve seat captivated to avoid extrusion and blockage of the valve
• High leak tightness integrity through diaphragm sealing
• Low internal volume with minimum dead spaces
• Manually actuated version see SERIES D240
ST ANDARD SPECIFICA
STANDARD TION
SPECIFICATION
Working pressure pmax 200 bar/3000 psi
Temperature range -25 °C up to + 65 °C
Helium leak rate at pmax
• internal 10-8 mbarl/sec
• external 10-8 mbarl/sec
• safety 10-8 mbarl/sec
Flow coefficient Cv 0,3
Seat orifice size 4 mm
DESIGN VARIANT
VARIANT
• Dip tube connections
• Flow restrictor threading
$
)
ORDERING
When ordering, please specify :
• Serial number or range
• Type of gas
• Connections
• Safety device specifications
• Options and special features
*
&
AISI 316L
AISI 316L
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
283
KEY FEATURES
FEATURES
• Elimination of cylinder cleaning as contamination is kept out even if
valve is left open
• Cost reduction as cylinder purging is no longer requested
• Increased safety as no filling is allowed without special adaptor
• Increased safety as no backflow occurs when mixing or manifolding
• Soft seat sealing arrangement offers low operating torque
• Valve seat captivated to avoid extrusion and blockage of the valve
• High leak tightness integrity through diaphragm sealing
• High performance thrust pad
STANDARD SPECIFICATION
Working pressure pmax 200 bar/3000 psi
Temperature range -25°C up to +65°C / -4oF up to +158oF
Helium leak rate at pmax
• internal 10-7 mbarl/sec
• external 10-7 mbarl/sec
Flow coefficient Cv 0,35
Seat orifice size 3,5 mm
Residual pressure 1 to 5 bar
DESIGN VARIANT
VARIANT
OPTIONS
• Alternative seat disc materials: PVDF, PI (Vespel®), PA6.6 (Nylon®), PCTFE
• Chrome or nickel plating
• Dip tube connection
SERIES D283 3
Body material BRASS
Safety device
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
325
KEY FEATURES
• Robust and safe in worst conditions.
• Soft seat sealing combined with a mechanical stop to prevent the seat extrusion in case of
excessive torque.
• The mechanical stop acts as secondary sealing in case of seat burning.
• Freedom of internal threads and springs insures minimum particle generation.
• High leak tightness integrity through diaphragm sealing up to 200 bar. (2900 PSI)
• Very low internal volume with minimum dead space.
• Positive and effective operation, valve lower spindle is mechanically linked to the upper spindle
and the operating hand-wheel.
• Valve can be operated using a flat key, if hand-wheel is broken.
• O-Rings in the gland and on spindle guarantee a secondary sealing against the atmosphere.
• Threaded vent hole. (e.g. to connect pipe away or sensor)
STANDARD SPECIFICATION
Working pressure p max 200 bar / 2900 psi
Temperature range -40 °C to + 65 °C
Helium leak rate at p max
• internal 10-8mbarl/sec
• external 10-8mbarl/sec
• safety 10-8mbarl/sec
Flow coefficient Cv 0.35
Seat orifice size 4 mm
Gas wetted materials see table on backside
08-8
CEODEUX
PURETEC
D 325
SAFETY DEVICE
Pressure relief devices are in accordance with CGA S-1.1
Burst disc materials are nickel or AISI 316L
OPTIONS
• Alternative body materials
and seat disc materials: PVDF, PI (Vespel ®)
ORDERING
When ordering, please specify:
• Serial number or range
• Body material
• Type of gas
• Connections
• Safety device specifications
• Options and special features
• Threading for flow restrictor
• Dip tube connection
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
392
KEY FEATURES
FEATURES
• Reduced dead spaces and gas wetted volumes allow easy purging process
• Freedom of internal threads and springs insures minimum particulate generation
• Very low internal volume with minimum dead spaces. This is particularly beneficial, when using
the valve for hygroscopic, corrosive, pyrophoric or high purity gases where inert gas purging is
necessary before opening or after closing the valve
• Freedom from seizure when used with corrosive gases. Gas does not come into contact with the
valve operating mechanism
• Positive and effective operation, valve lower spindle is mechanically linked to the upper spindle
and the operating mechanism
• Backed up welded diaphragms provide a permanent and durable gas tight seal
• Safe and easy acting operation system including manual override device: the valve can be
locked in the closed position by manual operation of the handwheel. This is an important safety
feature especially during transportation.
ST ANDARD SPECIFICA
STANDARD TION
SPECIFICATION
Working pressure pmax 165 bar / 2400 psi
Temperature range -25°C up to +65°C
Helium leak rate at pmax
• internal 10-8 mbarl/sec
• external 10-8 mbarl/sec
• safety 10-8 mbarl/sec
Flow coefficient Cv 0,25
Seat orifice size 4 mm
DESIGN VARIANT
VARIANT
Ø 75mm (2.95")
ORDERING
When ordering, please specify :
• Serial number or range
• Body material
• Type of gas
• Connections
• Safety device specifications
• Options and special features
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
380
KEY FEATURES
FEATURES
• Reduced dead spaces and gas wetted volumes allow easy purging process
• Freedom of internal threads and springs insures minimum particulate generation
• Very low internal volume with minimum dead spaces. This is particularly beneficial, when using
the valve for hygroscopic, corrosive, pyrophoric or high purity gases where inert gas purging is
necessary before opening or after closing the valve
• Freedom from seizure when used with corrosive gases. Gas does not come into contact with the
valve operating mechanism
• Positive and effective operation, valve lower spindle is mechanically linked to the upper spindle
and the operating mechanism
• Backed up welded diaphragms provide a permanent and durable gas tight seal
• Safe and easy acting operation system including manual override device: the valve can be
locked in the closed position by manual operation of the handwheel. This is an important safety
feature especially during transportation.
STANDARD SPECIFICA
STANDARD TION
SPECIFICATION
Working pressure pmax 200 bar / 3000 psi
Temperature range -40°C up to + 70°C
Helium leak rate at pmax
• internal 10-8 mbarl/sec
• external 10-8 mbarl/sec
• safety 10-8 mbarl/sec
Flow coefficient Cv 0,35
Seat orifice size 4 mm
DESIGN VARIANT
VARIANT
OPTIONS
ORDERING
When ordering, please specify :
• Serial number or range
• Body material
• Type of gas
• Connections
• Safety device specifications
• Options and special features
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
339
KEY FEATURES
FEATURES
• Soft seat sealing combined with a metal sealing
• High leak tightness integrity through diaphragm sealing
• Very low internal volume with minimum dead space
• Positive and effective operation, valve lower spindle is mechanically linked to the upper spindle
and the operating handwheel
• Backed up welded diaphragms provide a permanent and durable gas tight seal
• O-Rings in the gland and on spindle guarantee a secondary sealing
• Threaded vent hole
STANDARD SPECIFICA
STANDARD TION
SPECIFICATION
Working pressure pmax 120 bar / 1740 psi
Temperature range -40°C up to + 65°C
Helium leak rate at pmax
• internal 10-8 mbarl/sec
• external 10-8 mbarl/sec
• safety 10-8 mbarl/sec
Flow coefficient Cv ???????????????????????????????????????????
Seat orifice size 6 mm
DESIGN VARIANT
VARIANT
Ø 65 (2.56")
ORDERING
When ordering, please specify :
• Serial number or range
• Body material
• Type of gas
• Connections
• Safety device specifications
• Options and special features
AISI 316L
AISI 316L
NICKEL
NICKEL
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
388
KEY FEATURES
FEATURES
• Knife edge seat to prevent creation of silicate layer on the valve seat.
• Reduced dead spaces and gas wetted volumes allow easy purging process
• Freedom of internal threads and springs insures minimum particulate generation
• Very low internal volume with minimum dead spaces. This is particularly beneficial, when using
the valve for hygroscopic, corrosive, pyrophoric or high purity gases where inert gas purging is
necessary before opening or after closing the valve
• Freedom from seizure when used with corrosive gases. Gas does not come into contact with the
valve operating mechanism
• Positive and effective operation, valve lower spindle is mechanically linked to the upper spindle
and operating handwheel
• Backed up welded diaphragms provide a permanent and durable gas tight seal
• Safe and easy acting operation system including manual override device: the valve can be
locked in the closed position by manual operation of the handwheel. This is an important safety
feature especially during transportation
• O-Rings in the gland and on spindle guarantee a secondary sealing
• Threaded vent hole
STANDARD SPECIFICA
STANDARD TION
SPECIFICATION
Working pressure pmax 200 bar / 3000 psi
Temperature range -40°C up to + 70°C / -40oF up to +70oF
Helium leak rate at pmax
• internal 10-8 mbarl/sec
• external 10-8 mbarl/sec
• safety 10-8 mbarl/sec
Flow coefficient Cv 0,25
Seat orifice size 4 mm
DESIGN VARIANT
VARIANT
OPTIONS
• Seat disSeat disc materials: PI (Vespel®)
• Gas wetted components electrochemically polished
• Clean room assembling
ORDERING
When ordering, please specify:
• Serial number or range
• Type of gas
• Connections
• Safety device specifications
• Options and special features
SERIES D388 1
Body material AISI 316L
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
High flow dual port cylinder valve, tied diaphragm seal type,
for integrated system, for ultra high purity gases
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
344
KEY FEATURES
FEATURES
• Reduced dead spaces and gas wetted volumes allow easy purging process
• Freedom of internal threads and springs insures minimum particulate generation
• Very low internal volume with minimum dead spaces. This is particularly beneficial, when using
the valve for hygroscopic, corrosive, pyrophoric or high purity gases where inert gas purging is
necessary before opening or after closing the valve
• Freedom from seizure when used with corrosive gases. Gas does not come into contact with the
valve operating mechanism
• Positive and effective operation, valve lower spindle is mechanically linked to the upper spindle
and operating handwheel
• Backed up welded diaphragms provide a permanent and durable gas tight seal
• O-Rings in the gland and on spindle guarantee a secondary sealing
• Threaded vent hole
STANDARD SPECIFICA
STANDARD TION
SPECIFICATION
Working pressure pmax 165 bar / 2400 psi
Temperature range -40°C up to + 65°C / -40°F up to +149°F
Helium leak rate at pmax
• internal 10-8 mbarl/sec
• external 10-8 mbarl/sec
• safety 10-8 mbarl/sec
Withdrawal valve :
Flow coefficient Cv 0,35
Seat orifice size 4 mm
Filling valve:
Flow coefficient Cv 0,24
Seat orifice size 3,5 mm
DESIGN VARIANT
VARIANT
Safety device
Drawings
OPTIONS
ORDERING
When ordering, please specify:
• Serial number or range
• Type of gas
• Connections
• Safety device specifications
• Options and special features
SERIES D 344 1
Body material AISI 316L
AISI 316L
AISI 316L
AISI 316L
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
High flow dual port cylinder valve, tied diaphragm seal type,
pneumatically actuated, for integrated system, for ultra high
purity gases
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
394
KEY FEATURES
FEATURES
• Reduced dead spaces and gas wetted volumes allow easy purging process
• Freedom of internal threads and springs insures minimum particulate generation
• Very low internal volume with minimum dead spaces. This is particularly beneficial, when using
the valve for hygroscopic, corrosive, pyrophoric or high purity gases where inert gas purging is
necessary before opening or after closing the valve
• Freedom from seizure when used with corrosive gases. Gas does not come into contact with the
valve operating mechanism
• Positive and effective operation, valve lower spindle is mechanically linked to the upper spindle
• Backed up welded diaphragms provide a permanent and durable gas tight seal
• Safe and easy acting operation system including manual override device: the valve can be
locked in the closed position by manual operation of the handwheel. This is an important safety
feature especially during transportation
• O-Rings in the gland and on spindle guarantee a secondary sealing
• Threaded vent hole
STANDARD SPECIFICA
STANDARD TION
SPECIFICATION
Working pressure pmax 165bar / 2400 psi
Temperature range -40°C up to + 65° C / -40°F up to +149°F
Helium leak rate at pmax
• internal 10-8 mbarl/sec
• external 10-8 mbarl/sec
• safety 10-8 mbarl/sec
Withdrawal valve:
Flow coefficient Cv 0,35
Seat orifice size 4 mm
Filling vale:
Flow coefficient Cv 0,24
Seat orifice size 3,5 mm
Gas wetted materials see table on backside
08-8
CEODEUX
PURETEC
D 394
DESIGN VARIANT
Drawing=D320 Pressure relief devices are in accordance with CGA S-1.1
Burst disc materials are nickel or AISI 316L
Safety device
OPTIONS
• Alternative seat disc materials: PVDF, PI (Vespel®), PCTFE
• Gas wetted components electrochemically polished
• Clean room assembling
• Cleaning for UHP / ECD applications
• Threading for flow restrictor
• Dip tube connection
SERIES D 344 1
Body material AlSI 316L
AISI 316L
AISI 316L
AISI 316L
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
386
KEY FEATURES
FEATURES
• All metal seal, no contamination
• Reduced dead spaces and gas wetted volumes allow easy purging process
• Freedom of internal threads and springs insures minimum particulate generation
• Very low internal volume with minimum dead spaces. This is particularly beneficial, when using
the valve for hygroscopic, corrosive, pyrophoric or high purity gases where inert gas purging is
necessary before opening or after closing the valve
• Freedom from seizure where used with corrosive gases. Gas does not come into contact with
the valve operating mechanism
• Positive and effective operation, valve lower spindle is mechanically linked to the upper
spindle and the operating handwheel
• Backed up welded diaphragms provide a permanent and durable gas tight seal
• O-Rings in the gland and on spindle guarantee a secondary sealing
• Threaded vent hole
ST ANDARD SPECIFICA
STANDARD TION
SPECIFICATION
Working pressure pmax 45 bar
Temperature range -40oC up to +70oC
Helium leak rate at pmax
• internal 10-8 mbarl/sec
• external 10-8 mbarl/sec
• safety 10-8 mbarl/sec
Flow coefficient Cv 0,3
Seat orifice size 3,8 mm
DESIGN VARIANT
VARIANT Connection
A outlet
C inlet
F flow restrictor
G dip tube
OPTIONS ORDERING
• Alternativ body materials When ordering, please specify:
• Gas wetted components • Serial number or range
electrochemically polished • Body material
Body material
AISI 316L
Nickel
Monel
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
202
KEY FEATURES
• Soft seat sealing arrangement offers low operating torque
• Seat disc captivated to avoid extrusion
• High leak tightness integrity through diaphragm sealing
• Compact size
Standard specification
Working pressure pmax 200 bar/3000 psi
Temperature range -40°C (-40°F) up to 65°C (149°F)
Helium leak rate at pmax
- internal 10-7 mbar.l/s
- external 10-7 mbar.l/s
- safety device 10-8 mbar.l/s
Flow coefficient Cv 0,35
Seat orifice size 3,5 mm
Dip tube connections ¼” NPT on ¾”-14 NGT inlet and
M10x0,75 on 25E inlet
None on all other inlets
Gas wetted materials see table on back side
08-8
CEODEUX
PURETEC
D 202
DESIGN VARIANT
65
SAFETY DEVICE
OPTIONS
• Chrome plating for brass valves
99
A
• Without or customized dip tube connections
48
ORDERING
When ordering, please specify:
• serial number or range Connections: G
SERIES D202 3
Body material Brass
Brass
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
304
APPLICA TION
APPLICATION
see gas list in annex table
KEY FEATURES
• Tied diaphragm design with minimal gas wetted volume.
• Combined soft and metal seat design with low permeation rate.
• Positive operation due to mechanical link of the upper and lower spindle.
• Patented operating mechanism.
• Threaded weep hole for pipe away connection.
STANDARD SPECIFICATION
Working pressure p max 200 bar / 3000 psi
Temperature range -40 °C (-40°F) to + 65 °C (149°F)
Helium leak rate at p max
• internal 10-8 mbar.l/s
• external 10-8 mbar.l/s
• safety 10-8 mbar.l/s
Flow coefficient Cv 0.35
Seat orifice size 4 mm
Gas wetted materials see table on backside
08-8
CEODEUX
PURETEC
D 304
DESIGN VARIANT
Seat disc materials: PVDF, PI (Vespel®)
SAFETY DEVICE
Pressure relief devices are in accordance with CGA S-1.1
Burst disc materials are nickel or AISI 316L
OPTIONS
• Alternative body materials (Hastelloy®)
• electrochemically polished
Connections:
• gas service / Working pressure
A outlet
• valve material
C inlet
• Inlet & outlet connections ( A & C acc, to national standard)
F flow restrictor (std: 5/16”-UNF)
• Threading for flow restrictor (F)
G dip tube (std: M10 x 0.75 or 1/4”NPT)
• Threading dip tube connection (G)
• Surface treatment
• Pressure relief device
• Packaging and conditioning
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
354
APPLICA TION
APPLICATION
see gas list in annex table
KEY FEATURES
• Tied diaphragm design with minimal gas wetted volume.
• Combined soft and metal seat design with low permeation rate.
• Positive operation due to mechanical link of the upper and lower spindle.
• Threaded weep hole for pipe away connection.
• Strong closing force with the use of a hydraulic amplifier
STANDARD SPECIFICATION
Working pressure p max 200 bar / 3000 psi
Temperature range -25 °C (-4°F) to + 65 °C (149°F)
Helium leak rate at p max
• internal 10-8 mbar.l/s
• external 10-8 mbar.l/s
• safety 10-8 mbar.l/s
Flow coefficient Cv 0.35
Seat orifice size 4 mm
Gas wetted materials see table on backside
Actuator air pressure 5-7 bar (72-100PSI)
08-8
CEODEUX
PURETEC
D 354
DESIGN VARIANT
Seat disc materials: PVDF, PI (Vespel®)
SAFETY DEVICE
Pressure relief devices are in accordance with CGA S-1.1
Burst disc materials are nickel or AISI 316L
OPTIONS
• Alternative body materials (Hastelloy®)
• electrochemically polished
Connections:
• gas service / Working pressure
A outlet
• valve material
C inlet
• Inlet & outlet connections ( A & C acc, to national standard)
F flow restrictor (std: 5/16”-UNF)
• P Air pressure connexion
G dip tube (std: M10 x 0.75 or 1/4”NPT)
• Threading for flow restrictor (F)
P Air pressure connexion (M5 or 1/8” NPT or G1/8)
• Threading dip tube connection (G)
• Surface treatment
• Pressure relief device
• Packaging and conditioning
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
389
APPLICA TION
APPLICATION
see gas list in annex table
KEY FEATURES
• Tied diaphragm design with minimal gas wetted volume.
• Combined soft and metal seat design with low permeation rate.
• Positive operation due to mechanical link of the upper and lower spindle.
• Threaded weep hole for pipe away connection.
• Strong closing force with the use of a hydraulic amplifier
STANDARD SPECIFICATION
Working pressure p max 200 bar / 3000 psi
Temperature range -25 °C (-4°F) to + 65 °C (149°F)
Helium leak rate at p max
• internal 10-8 mbar.l/s
• external 10-8 mbar.l/s
• safety 10-8 mbar.l/s
Flow coefficient Cv 0.55
Seat orifice size 6 mm
Gas wetted materials see table on backside
Actuator air pressure 5-7 bar (72-100PSI)
08-8
CEODEUX
PURETEC
D 389
DESIGN VARIANT
Seat disc materials: PVDF, PI (Vespel®)
SAFETY DEVICE
Pressure relief devices are in accordance with CGA S-1.1
Burst disc materials are nickel or AISI 316L
OPTIONS
• Alternative body materials (Hastelloy®)
• electrochemically polished
Connections:
• gas service / Working pressure
A outlet
• valve material
C inlet
• Inlet & outlet connections ( A & C acc, to national standard)
F flow restrictor (std: 5/16”-UNF)
• P Air pressure connexion
G dip tube (std: M10 x 0.75 or 1/4”NPT)
• Threading for flow restrictor (F)
P Air pressure connexion (M5 or 1/8” NPT or G1/8)
• Threading dip tube connection (G)
• Surface treatment
• Pressure relief device
• Packaging and conditioning
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
High pressure line valve in stainless steel for inert & various
gases.
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
605
APPLICA TION
APPLICATION
Isolation valve in gas filling stations or installation as main shut-off
valve on bundles or trailers
KEY FEATURES
• 2-piece sturdy stem design.
• Silver ring combined with a PA (or PCTFE) seat disc for lowest tightness torque.
• No gas in contact with the operating mechanism & O-ring fitted into gland nut to exclude
humidity
• Soft seat encapsulated into the spindle to avoid extrusion and good sealing performances.
• Lower spindle design allows a smooth opening of the valve, and prevents adiabatic
compression.
STANDARD SPECIFICATION
Working pressure p max 300 bar / 4350 psi
Temperature range -25 °C (-4°F) to + 65 °C (149°F)
Helium leak rate at p max
• internal 10-3 mbar.l/s
• external 10-3 mbar.l/s
Flow coefficient Cv 1.5
Seat orifice size 10 mm
Gas wetted materials see table on backside
08-8
CEODEUX
PURETEC
D 605
OPTIONS
• Seat disc & O-ring materials according gas applications
Connections:
A outlet
C inlet
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
High flow line valves, tied diaphragm double seal type, for
ultra high purity corrosive gases
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
604
APPLICA TION
APPLICATION
see gas list in annex table
KEY FEATURES
• Tied diaphragm design with minimal gas wetted volume.
• Combined soft and metal seat design with low permeation rate.
• Positive operation due to mechanical link of the upper and lower spindle.
• Patented operating mechanism.
• Threaded weep hole for pipe away connection.
STANDARD SPECIFICATION
Working pressure p max 200 bar / 3000 psi
Temperature range -40 °C (-40°F) to + 65 °C (149°F)
Helium leak rate at p max
• internal 10-8 mbar.l/s
• external 10-8 mbar.l/s
• safety 10-8 mbar.l/s
Flow coefficient Cv 0.3
Seat orifice size 4 mm
Gas wetted materials see table on backside
08-8
CEODEUX
PURETEC
D 604
WKUHDGV0
RQ
9,(:;
DESIGN VARIANT
Seat disc materials: PVDF, PI (Vespel®)
Ø65 (2.56")
OPTIONS
• electrochemically polished
§ 84
REQUEST FOR QUOTATION
please specify using product definition sheet Fr03.5.05.002
A
• valve material
• Inlet & outlet connections ( A & C acc, to national standard)
§ 11,2
• Surface treatment § 36
Connections:
A outlet
C inlet
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
High flow line valves, tied diaphragm double seal type, for
ultra high purity corrosive gases
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
639
APPLICA TION
APPLICATION
see gas list in annex table
KEY FEATURES
• Tied diaphragm design with minimal gas wetted volume.
• Combined soft and metal seat design with low permeation rate.
• Positive operation due to mechanical link of the upper and lower spindle.
• Patented operating mechanism.
• Threaded weep hole for pipe away connection.
STANDARD SPECIFICATION
Working pressure p max 200 bar / 3000 psi
Temperature range -40 °C (-40°F) to + 65 °C (149°F)
Helium leak rate at p max
• internal 10-8 mbar.l/s
• external 10-8 mbar.l/s
• safety 10-8 mbar.l/s
Flow coefficient Cv 0.5
Seat orifice size 6 mm
Gas wetted materials see table on backside
08-8
CEODEUX
PURETEC
D 639
WKUHDGV0
RQ
9,(:;
DESIGN VARIANT
Seat disc materials: PVDF, PI (Vespel®)
Ø65 (2.56")
OPTIONS
• electrochemically polished
§ 84
REQUEST FOR QUOTATION
please specify using product definition sheet Fr03.5.05.002
A
• valve material
• Inlet & outlet connections ( A & C acc, to national standard)
§ 11,2
• Surface treatment § 36
Connections:
A outlet
C inlet
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
High flow line valves, tied diaphragm seal type, for ultra
high purity corrosive gases
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
654
APPLICA TION
APPLICATION
see gas list in annex table
KEY FEATURES
• Tied diaphragm design with minimal gas wetted volume.
• Combined soft and metal seat design with low permeation rate.
• Positive operation due to mechanical link of the upper and lower spindle.
• Threaded weep hole for pipe away connection.
• Strong closing force with the use of a hydraulic amplifier
STANDARD SPECIFICATION
Working pressure p max 200 bar / 3000 psi
Temperature range -40 °C (-40°F) to + 65 °C (149°F)
Helium leak rate at p max
• internal 10-8 mbar.l/s
• external 10-8 mbar.l/s
• safety 10-8 mbar.l/s
Flow coefficient Cv 0.3
Seat orifice size 4 mm
Gas wetted materials see table on backside
Actuator air pressure 5-7 bar (72-100PSI)
08-8
CEODEUX
PURETEC
D 654
25,4 (1")
DESIGN VARIANT
Seat disc materials: PVDF, PI (Vespel®)
4 threads M5
§ 67
P
OPTIONS
• Alternative body materials (Hastelloy®)
§ 124
• electrochemically polished
A
§ 36
REQUEST FOR QUOTATION
§ 11,2
§ 78
please specify using product definition sheet Fr03.5.05.002
Connections:
• gas service / Working pressure
A outlet
• valve material
C inlet
• Inlet & outlet connections ( A & C acc, to national standard)
P Air pressure connection (M5 or 1/8” NPT or G1/8)
• P Air pressure connection
• Surface treatment
• Packaging and conditioning
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322
CEODEUX
PURETEC
High flow line valves, tied diaphragm seal type, for ultra
high purity corrosive gases
D
Droits de modifications réservés / All rights of change reserved / Änderungsrechte vorbehalten
689
APPLICA TION
APPLICATION
see gas list in annex table
KEY FEATURES
• Tied diaphragm design with minimal gas wetted volume.
• Combined soft and metal seat design with low permeation rate.
• Positive operation due to mechanical link of the upper and lower spindle.
• Threaded weep hole for pipe away connection.
• Strong closing force with the use of a hydraulic amplifier
STANDARD SPECIFICATION
Working pressure p max 200 bar / 3000 psi
Temperature range -40 °C (-40°F) to + 65 °C (149°F)
Helium leak rate at p max
• internal 10-8 mbar.l/s
• external 10-8 mbar.l/s
• safety 10-8 mbar.l/s
Flow coefficient Cv 0.5
Seat orifice size 6 mm
Gas wetted materials see table on backside
Actuator air pressure 5-7 bar (72-100PSI)
08-8
CEODEUX
PURETEC
D
25,4 (1")
689
DESIGN VARIANT
Seat disc materials: PVDF, PI (Vespel®)
4 threads M5
§ 67
P
OPTIONS
• Alternative body materials (Hastelloy®)
§ 124
• electrochemically polished
A
§ 36
§ 11,2
REQUEST FOR QUOTATION § 78
Connections:
• gas service / Working pressure
A outlet
• valve material
C inlet
• Inlet & outlet connections ( A & C acc, to national standard)
P Air pressure connection (M5 or 1/8” NPT or G1/8)
• P Air pressure connection
• Surface treatment
• Packaging and conditioning
www
rotarex.com
IS
ISOO 9001
CERTIFIED
ROTAREX
Group 24, route de Diekirch - B.P. 19 L-7505 Lintgen (Europe) Fax: +352 32 78 32 - 322