Professional Documents
Culture Documents
LE4S Series: DIN W48×H48mm Digital Backlight LCD Timer
LE4S Series: DIN W48×H48mm Digital Backlight LCD Timer
LE4S Series: DIN W48×H48mm Digital Backlight LCD Timer
K-20
LCD Timer(Touch Type)
Specifications (A)
Photo
electric
sensor
Model LE4S LE4SA
(B)
Repeat error Fiber
optic
sensor
Setting error Max. ±0.01% ±0.05sec.(Power ON Start)
Max. ±0.01% ±0.05sec.
Voltage error Max. ±0.005% ±0.03sec.(Signal ON Start) (C)
Door/Area
sensor
Temperature error
(D)
Insulation resistance 100MΩ(at 500VDC megger) Proximity
sensor
Mechanical 0.75mm amplitude at frequency of 10 to 55Hz(for 1 min.) in each of X, Y, Z directions for 1hour
Vibration (F)
Rotary
Malfunction 0.5mm amplitude at frequency of 10 to 55Hz(for 1 min.) in each of X, Y, Z directions for 10 minutes encoder
Approval
(H)
Temp.
Unit weight Approx. 98g controller
(I)
SSR/
Dimensions Power
controller
(J)
Counter
6 70 ● Panel cut-out
56
(K)
48 2 Min. 65 Timer
(L)
Panel
meter
45 +0.6
0
(M)
Min. 65
Tacho/
44.8
56
Speed/ Pulse
45 +0.6
0
meter
(N)
Display
unit
(O)
Sensor
controller
(P)
Switching
mode power
● Bracket and mounting supply
(Q)
Stepper
motor&
Driver&Controller
(R)
Graphic/
Logic
panel
※Insert product into a panel, fasten (S)
bracket by pushing with tools as Field
network
shown above. device
(T)
Software
(U)
Other
K-21
LE4S Series
Connections
LE4S
RESET 4 5
- + 24-240VAC 50/60Hz
SOURCE 24-240VDC
LE4SA
● [ON.D] [ON.D.II] [FK] [FKI] [INT] [T] [T.I] mode
4 5
3 6 CONTACT OUT:
250VAC 3A RESISTIVE LOAD
2 7
1 8
(Instantaneous (Time limit (Time limit contact 1c)
contact 1c) contact1c)
- + 24-240VAC 50/60Hz
SOURCE 24-240VDC
● [ - ] mode
4 5
3 6
CONTACT OUT:
Contact 2 7 Contact
250VAC 3A RESISTIVE LOAD
(Time limit contact 1a) (Time limit contact 1a)
1 8
- + 24-240VAC 50/60Hz
SOURCE 24-240VDC
K-22
LCD Timer(Touch Type)
Input connections (A)
Photo
electric
LE4S is No-voltage input(Short-circuit and open) type. sensor
(B)
Fiber
Solid-state input Contact input optic
sensor
+ + START
START RL START (D)
- - RESET
RESET RESET S1 Proximity
sensor
INHIBIT INHIBIT S2 INHIBIT
Q1 Q2
S3 (E)
Input 0V Input 0V Input 0V Pressure
sensor
(H)
Temp.
controller
● Time unit
It displays the time unit. (K)
Timer
● Output display (h:hour)(m:min.)(s:sec.)
It displays the status ※When the time is progressing, it
of output contact. is flashing at a rate of (0.5sec.) (L)
Panel
meter
(N)
Display
● Operation mode unit
● UP/DOWN
It displays the current operation mode.
It displays time progressing
(ex: OND=ON Delay) (O)
UP(▲), DOWN(▼). Sensor
controller
(P)
● SHIFT key Switching
● Key lock display Used for advancing to setting time change mode power
supply
It displays the status mode and moving to each digit.
of key lock. (Q)
Stepper
motor&
Driver&Controller
(T)
Software
(U)
Other
K-23
LE4S Series
Function and time setting
Configuration
Power On
Setting time
Reset key change mode
key
key
RUN mode
key
for 3sec. while pressing key
Checking out-
Function key put
setting mode for 3sec. contact status
● Reset
Reset using key in Run mode
● Run mode
The operation status(When power is on for the first time : factory default setting) is displayed.
It could enter into function setting mode, setting value change mode and output contact status mode.
※If no key is pressed over 60 sec. in setting time change mode, it will return to Run mode and previous parameter
value is not stored.
K-24
LCD Timer(Touch Type)
Function setting mode (A)
Photo
electric
LE4S sensor
(B)
Function setting mode Fiber
optic
sensor
2)Time range
(C)
[OND], [ONd1], Door/Area
key sensor
[ONd2], [INT],
1)Output operation 3)One-Shot output time
mode [INt1], [OFD]
(D)
mode Proximity
key 3sec. key key sensor
※ONd2
(E)
mode Pressure
RUN mode
sensor
7)Key lock key tOFFTime range tON Time range
(F)
[FLK], [FLk1], key key Rotary
encoder
[NFD], [NFd1]
key 3sec. mode
(G)
Connector/
key Socket
6)Backlight On/Off 5)Min. input signal 4)Time Up/Down
(H)
key key Temp.
controller
(I)
SSR/
Power
controller
LE4SA
(J)
Function setting mode Counter
2)Time range
(K)
Timer
(R)
key key Graphic/
Logic
panel
(S)
Field
network
device
Factory default
(T)
LE4S LE4SA Software
K-25
LE4S Series
Output operation mode
● LE4S/LE4SA output operation mode
1) In function setting mode, it enter into output operation mode as shown in the [Fig. 1].
2) Select proper output operation mode using and key.
(Refer to Output operation flowchart)
3) Press key to set output operation mode and move to next mode.
4) If pressing key for 3 sec. in any function setting mode, it will return to Run mode.
[Fig.1]
K-26
LCD Timer(Touch Type)
Time Range (A)
Photo
electric
sensor
-Time range[tRNG]
(J)
: OND, ONd1, ONd2, INT, INt1, OFD mode Counter
(M)
Tacho/
Speed/ Pulse
meter
3) Press key to complete the time range setting and the next mode. (Q)
Stepper
4) If pressing key for 3 sec., it will return to Run mode. motor&
※When FLK, FLk1, NFD, NFd1, S-D, TWN, TWn1 time range[T!RG, T@RG or Driver&Controller
(S)
Field
network
※Time range flowchart device
(T)
Software
K-27
LE4S Series
● One-shot output time setting
When output operation mode ON Delay 2[ONd2],
1)In function setting mode, if it enter into One-shot output time setting mode as shown in
the [Fig. 2], the last digit will flash.
2) Set One-shot output time using and key.(setting range: 0.01s to 99.99s)
3) Pressing key to complete one-shot output time setting and move to the next mode.
4) If pressing key for 3 sec. in any function setting mode, it will return to Run mode.
key
key
3) Press key to complete UP/DOWN setting and move to the next mode.
4) If pressing key for 3sec. in any function setting mode, it will return to Run mode.
[Fig.3] ※Factory default
key
key
3) Press key to complete input signal width and move to the next mode.
[Fig.4]
4) If Pressing key over 3 sec. in any function setting mode, it will return to Run mode.
※Factory default
1) In function setting mode, if it enter into output contact setting mode, the characters will be
displayed as shown in the [Fig. 5].
2)Select time limit 1c+instant limit 1c or time limit 2c using , keys.
(Refer to LE4SA Connections on K-20 page for output contact connections)
key
key
[Fig.5] 3) Press key to complete output contact setting and move to the next mode.
※Factory default 4) If pressing key for 3 sec. in any function setting, it will return to Run mode.
※Except for Star-Delta, Twin and Twin 1 modes(2C is set automatically)
※If pressing key in Run mode, output contact setting value will be displayed.
(If no key is pressed over 3 sec., it will enter into function setting mode.)
K-28
LCD Timer(Touch Type)
● Backlight ON/OFF setting (A)
Photo
1) In function setting mode, if it enter into Backlight ON/OFF setting mode, the characters will electric
sensor
be displayed as shown in the [Fig. 6].
(B)
2) Select Backlight ON or OFF using , key. Fiber
optic
sensor
key
(C)
Door/Area
key sensor
3) Press key to complete Backlight ON/OFF setting and move to the next mode. (D)
Proximity
sensor
[Fig.6]
4) If pressing key for 3 sec. in any function setting mode, it will return to Run mode.
※Factory default (E)
Pressure
sensor
● Key Lock setting
1) In function setting mode, if it enter into Key Lock setting mode, the characters will be (F)
Rotary
displayed as shown in the [Fig. 7]. encoder
3) Press key to complete key lock setting and move to the next mode.
4) If pressing key for 3 sec. in any function setting mode, it will return to Run mode. (K)
Timer
※Factory default for LE4S is lOFF and Factory default for LE4SA is LOc1.
※Key Lock function (L)
Panel
meter
Display Function
lOFF Turns off the key Lock mode. (M)
Tacho/
Speed/ Pulse
LOc1 key cannot be used. meter
(O)
Sensor
Setting time change controller
Please set operation time according to following instruction as the setting is different depending on the output operation (P)
Switching
mode. mode power
supply
● Output operation mode : OND, ONDⅠ, ONDⅡ, INT, INTⅠ, OFF D (Q)
(LE4SA does not have no ONDⅠ, INTⅠ, OFF D.) Stepper
motor&
Driver&Controller
(R)
Graphic/
Logic
panel
(S)
Field
network
device
(T)
Software
K-29
LE4S Series
● Output operation mode : FK, FK I
※It is able to change the setting time during the time progressing, but be sure about the time progressing while changing
of the time.
※If pressing key while setting time is shorter than min. setting time, setting value will be flickering three times and it will
be returned to setting mode again, not to RUN mode.
※If there is no additional key operations in 60 sec. after entering into setting mode, it will be return to RUN mode. (set
value is not stored.)
※Min. setting time : 0.01 sec.
(In case of : OND, ONd1, ONd2 modes, it is able to set "0" since no min. setting time is applied.)
K-30
LCD Timer(Touch Type)
LE4S Output operation mode T = Setting time, T > Ta (A)
Photo
electric
Mode Time chart Operation sensor
T T Ta T
[OND] (B)
POWER Fiber
optic
OND START
sensor
RESET ② ③
RELAY OUT ① ④
(C)
Set time POWER Door/Area
sensor
UP 0
Set time START
T
DOWN 0 RELAY
(D)
ON Delay OUT Proximity
1. Timing operation starts when START signal is ON at status of power on. sensor
2. Output will be ON when timing operation is progressed up to the setting time. Display value will be
HOLD. (① position) (E)
3. When RESET signal is ON, display value and output will be reset.(② position) Pressure
sensor
T > Ta 4. If RESET signal is OFF while START signal is ON,“STEP 1”will be restarted.(③ position) T = set time
5. When START signal is OFF, display value and output will be reset.(④ position)
[ONd1] T T Ta T (F)
POWER Rotary
encoder
ONDⅠ START ②
RESET ③
(G)
RELAY OUT ① Connector/
POWER
Set time Socket
UP 0 RESET
Set time START (H)
T Temp.
ON Delay 1 DOWN 0 RELAY controller
OUT
1. Timing operation starts when START signal is ON at status of power on.
(I)
2. Output will be ON when timing operation is progressed up to the setting time. Display value will be SSR/
HOLD.(① position) Power
T > Ta 3. Even though START signal is applied repeatedly, only the initial signal is recognized.(② position) T = set time controller
4. When RESET signal is ON, display value and output will be reset.(③ position)
[ONd2] T T Ta Ta T (J)
Counter
POWER
START ②
ONDⅡ
RESET
(K)
RELAY OUT ① Timer
Set time
UP POWER
0
(L)
Set time START Panel
DOWN Tout meter
0 RELAY
ON Delay 2 T
1. Timing operation starts when START signal is ON at status of power on. OUT
(One-shot output) (M)
2. Time limit output will be ON and goes OFF during Tout setting time when timing operation is progressed Tacho/
up to the setting time. Display value will be HOLD.(① position) Speed/ Pulse
meter
3. When RESET signal is ON, display value and output will be reset.
4. If START signal is applied while time is progressing, Timing operation will be reset and started again. (② Tout = output time
(N)
T > Ta position) T = set time Display
5. Tout setting range: 0.01 sec to 99.99 sec. unit
K-31
LE4S Series
LE4S Output operation mode T = Setting time, T > Ta
Mode Time chart Operation
T T Ta T
[INT]
POWER
INT START ②
RESET
RELAY OUT ①
Set time POWER
UP 0 START
T
Set time
RELAY
Interval DOWN
0 OUT
1. Output will be ON when START signal is ON at status of power on and Timing operation starts.
2. Output will be OFF when timing operation is progressed up to the setting time. Display value will be HOLD.
3. When RESET signal is ON, display value and output will be reset.(① position)
T > Ta 4. If RESET signal is OFF when START signal is ON,“STEP 1” will be restarted. T = set time
5. When START signal is OFF, display value and output will be reset.(② position)
T Ta T T T
[INt1]
POWER
INTⅠ START
RESET ① ②
RELAY OUT
Set time POWER
UP START
0
Set time T T
RELAY
Interval 1 DOWN 0 OUT
1. Output will be ON when START signal is ON at status of power on and Timing operation starts.
2. Output will be OFF when timing operation is progressed up to the setting time. Display value will be HOLD.
3. Even though START signal is applied repeatedly, only the initial signal is recognized.(① position)
4. If START signal is ON after timing operation is progressed up to the setting time, Output will be ON and setting
T > Ta time will be reset and then timing setting starts. T = set time
5. When RESET signal is ON, display value and output will be reset.(② position)
Ton Toff Ta Ta Toff Ta Ton Ta Ton Toff
[NFD]
POWER
ON OFF D START
RESET ① ②
RELAY OUT
Toff
Ton POWER
UP
0 START
Toff Ton Toff
Ton
DOWN RELAY
ON-OFF Delay 0 OUT
1. If START signal is ON when power is on, Output will be ON when timing operation is progressed up to the Ton
setting time(On-Delay). IF START signal is OFF, output will be ON when timing operation is progressed up to
the Toff setting time (OFF-Delay).
2. If START signal is applied repeatedly, output is ON and display value will be reset.(① position)
3. When RESET signal is ON, display value and output will be reset. When RESET signal is OFF while START
T > Ta signal is ON, it will be operating as On-Delay.(② position) Ton, Toff = set time
4. It is able to set each Toff time and Ton time separately.
Ton Toff Ta Ta Toff Ta Ton Ta Ton Toff
[NFd1] POWER
ON OFF DⅠ START
RESET ① ②
RELAY OUT
Toff
Ton
UP POWER
0
Toff
Ton START
DOWN Ton Toff
0 RELAY
ON-OFF Delay 1 1. If START signal is ON when power is on, timing operation starts. Output will be ON when timing operation OUT
is progressed up to the Ton setting time(On-Delay). IF START signal is OFF, output will be ON when timing
operation is progressed up to the Toff setting time (OFF-Delay).
2. Output will be ON when START signal is ON and goes OFF during setting time and display value will be reset.(① position)
3. Output will be OFF when START signal is OFF and goes ON during setting time and display value will be reset.(① position)
4. When RESET signal is ON, display value and output will be reset. When RESET signal is OFF while START
T > Ta signal is ON, it will be operating as On-Delay.(② position) Ton, Toff = set time
5. It is able to set each Toff time and Ton time separately.
Ta T Ta Ta T
[OFD]
POWER
OFF D START
RESET
RELAY OUT POWER
Set time
START
UP 0 T
RELAY
OFF Delay Set time OUT
DOWN 0
1. If START signal is ON when power is on, output will be ON.
2. When START signal is OFF, timing operation starts. Output will be OFF when timing operation is progressed up
T > Ta to the setting time. Display value will be HOLD. T = set time
3. When RESET signal is ON, display value and output will be reset.
※Initial status : UP mode-display value is "0", output is "OFF". DOWN mode-display value is "setting time", output is "OFF".
K-32
LCD Timer(Touch Type)
LE4SA Output operation mode T = Setting time, T > Ta, Rt = Reset time
(A)
Photo
electric
Mode Time chart Operation sensor
[OND] T Rt T T (B)
Fiber
POWER optic
OND ※RESET sensor
Time limit contact
(⑧-⑥)
Instantaneous contact (C)
(①-③) Door/Area
Set time POWER sensor
UP
0 T
Time limit (D)
Set time contact Proximity
ON Delay DOWN 0 output sensor
POWER
FK ※RESET (L)
Time limit contact Panel
(⑧-⑥) meter
Instantaneous contact
(①-③)
Toff (M)
Ton POWER Tacho/
Speed/ Pulse
UP meter
0 Toff Ton Toff Ton
Time limit
Flicker Toff
contact
Ton
(Toff operation DOWN output
(N)
Display
precedes) 0 unit
1. Control output will be repeatedly OFF during Toff setting time and will be ON during Ton setting time when
power is ON. Ton, Toff = set time (O)
Ton, Toff > Ta 2. If selecting time limit 1c + instantaneous 1c mode, instantaneous output will be ON when power is ON and goes Sensor
OFF when power is OFF. Enables to set Ton and controller
3. If pressing RESET key, display value and time limit output will be reset. Toff time differently.
4. It is able to set each Toff time and Ton time separately. In [ ] mode, timing operation starts with Toff. (P)
Switching
[FLk1] Ton Toff Ton Toff Ton Ta Rt Ton Toff Ton Toff mode power
supply
POWER
FKⅠ ※RESET (Q)
Time limit contact Stepper
(⑧-⑥) motor&
Driver&Controller
Instantaneous contact
(①-③)
Toff (R)
Ton POWER Graphic/
UP Logic
0 Ton Toff Ton Toff panel
Time limit
Flicker 1 Toff
Ton contact (S)
(Ton operation DOWN output Field
precedes) 0 network
device
1. Control output will be repeatedly ON during Ton setting time and will be OFF during Toff setting time when
power is ON. Ton, Toff = set time
2. If selecting time limit 1c + instantaneous 1c mode, instantaneous output will be ON when power is ON and goes (T)
OFF when power is OFF. Enables to set Ton and Software
3. If pressing RESET key, display value and time limit output will be reset. Toff time differently.
4. It is able to set each Ton time and Toff time separately. In [ ] mode, timing operation starts with Ton.
(U)
※Initial status : UP mode-display value is "0", output is "OFF". DOWN mode-display value is "setting time", output is "OFF". Other
※Instantaneous contact(OUT2) will be returned when power is off.
※RESET key is locked for default set and release the lock to use.
K-33
LE4S Series
LE4SA Output operation mode Rt : Reset time(Min. 500ms)
[ ] T1 T2 Rt T1 T2
POWER
-
※RESET
contact(⑧-⑥)
contact(①-③)
POWER
Set time T1 T1
T2
Star-Delta UP 0 contact
T1 T2
Set time
(Output will be set DOWN
T2
0 contact
automatically
as Time limit 2c) 1. contact will be ON when power is ON and Timing operation starts.
2. contact will be OFF when timing operation is progressed up to the T1 setting time.
Timing operation will be reset and started again. ※T1 : set time
3. contact will be ON when timing operation is progressed up to the T2 switching time.
Display value will be HOLD. T2 : switching time
4. If pressing RESET key, display value and - contacts will be reset. ( - switching time)
5. It is able to set each T1 and T2 time separately.
[ ] T1 T2 Rt T1 T2 T1
POWER
T
※RESET
T1 contact(⑧-⑥)
T2 contact(①-③) POWER
Set time T1 T1
Twin T2
UP 0 T1 contact
Set time T1 T2
(Output will be set T2
automatically DOWN 0 T2 contact
as Time limit 2c) T1, T2 = set time
1. T1 contact will be ON when power is ON and Timing operation starts.
2. T1 contact will be OFF and T2 contact will be ON when timing operation is progressed up to the T1 setting
time. Timing operation will be reset and started again. T2 contact will be OFF when timing operation is pro-
gressed up to the T2 setting time. Display value will be HOLD. Enables to set T1 and T2
3. If pressing RESET key, display value and T1, T2 contacts will be reset. time same or differently
4. It is able to set each T1 and T2 time separately.
[ ] T1 T2 Ta Rt T1 T2
POWER
TⅠ
※RESET
T1 contact(⑧-⑥)
T2 contact(①-③)
※Initial status : UP mode-display value is "0", output is "OFF". DOWN mode-display value is "setting time", output is "OFF".
※Instantaneous contact(OUT2) will be returned when power is off.
※RESET key is locked for default set and release the lock to use.
K-34
LCD Timer(Touch Type)
Proper usage (A)
Photo
electric
sensor
Caution When connecting more than 2 timers with 1 relay contact
It may give an electric shock if touch the input signal for input or transistor, please wire following <Fig. 2 >. (B)
Fiber
terminal(Between START, RESET, INHIBIT and terminal Please use relay contact or transistor to start. optic
sensor
②) when the power is supplied. (Time error can occurs under 100ms setting because of
rising time of Timer). (C)
Door/Area
Power connection sensor
● LE4S, LE4SA work stably within range of rated power. RESET ④ Power
Input contact (E)
(If using power line with another high voltage line or or transistor INHIBIT ① Pressure
sensor
energy line in the same conduit, it may cause inductive
voltage. (F)
Therefore please use seperate conduit for power line) LE4S
Rotary
encoder
Short-
Power start circuit
current START ③ (G)
● Caution for power rising time(100ms) after power on and RESET ④
Connector/
Socket
power falling time(100ms) after power off. INHIBIT ①
(H)
Temp.
Power ON controller
OFF
100ms The unstable time 100ms (I)
against the input signal SSR/
Power
LE4S controller
Graphic/
● Please use Power supply with over current protection Logic
panel
circuit.(250V 1A fuse)
● When using relay contact as input signal, please use a (S)
Field
contact that can function reliable at 5VDC, 1mA. network
device
● In case of connecting START terminal (③) and power Rectification Transformer
terminal (②) of LE4S, do not use it to start at the same circuit with isolation (T)
Software
time applying power. < External sensor power supply >
● LE4S is transformer less type, therefore please check
following for connecting relay contact for input signal and ●Be sure that the specifications of this unit. Because (U)
Other
transistor. when supplying the power to LE4SA, this unit operates
instantly. (If supplying the power without the right
checking, it may cause malfunction.)
● , , operation modes are available to set
as "0".
K-35
LE4S Series
Interval mode
It is able to make Instantaneous ON and time limit OFF
(Holding device) with using interval mode.
T : Timer
Instan-
START START
taneous
Time
limit
Time
limit
Noise
We test 2kV, pulse width 1㎲ against Impulse voltage
between power terminals and 1kV, pulse width 1㎲ at noise
simulator against external noise voltage. Please install MP
condensor (0.1 to 1㎌) or oil condensor between power
teminals when over impulse noise voltage occurs.
Environment
Please avoid the following places;
● Where this product may be damaged by strong impact or
vibration.
● Where there are corrosive gas or flammable gas and
water, oil, dust exist.
● Where magnetic and electrical noise occurs.
● Where there are high temperature and humidity beyond
rated specification.
● Where there are strong alkalis and acids.
● Where there are direct rays of sun.
K-36