Professional Documents
Culture Documents
02 - RCC Foundation Design Report
02 - RCC Foundation Design Report
1. INTRODUCTION
This document describes the structural layout, loads and load combinations, material
properties and methodology used for analysis and design of foundations, plinth beams and
pedestal columns for the proposed structure of Tata Motors service centre at Pikine as per the
relevant codes and standards. The overall plan dimension of the proposed Steel building is 103
m x 37 m (3811 m2). The scope of work is to design the substructure of the proposed building.
pg. 2
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
STRUCTURAL DESCRIPTION
This section describes the basic structural description and layout of the proposed structure.
The structure is described with images as shown below. The Overall plan dimension of
proposed steel building is 103 m x 37 m.
pg. 3
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
pg. 4
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
STAAD Pro Analysis and design software is used for the analysis and design of the Steel building
structure. For the analysis 3D skeleton shall be modelled and analyzed by using the STAAD Pro
analysis and design software.
The structure is analyzed with the Eurocode Combinations and exported to STAAD.foundation.
Hence, the analysis and design of foundations is done using STAAD.foundation Software. The
analysis of plinth beam and pedestals are done in STAAD pro software
Material Properties
The material properties are used for defining the stiffness calculation of the modelled
structural members in the analysis.
Table-
Table-4.1 Elastic Properties of Materials
Sl. No. Material Member description Elastic Modulus Poisson’s Unit weight
(kN/m2) Ratio (kN/m3)
1 High Strength deformed bars Footing, Pedestals, 2 x 108 0.3 78.5
(fy =500 N/mm2) Plinth Beam
pg. 5
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
This section describes the various loads considered for the analysis and design of the proposed
structure. The loads and load calculations are described below.
Loads:
The foundations are designed for support reactions of the superstructure which is designed
for relevant loads. In addition to the support reactions, the Self weight of the substructure and
backfill is considered.
Load Combinations
The foundations for the proposed structure is designed for both strength and serviceability
criteria. For the strength design, load combinations as specified in BS EN shall be used. For
ascertaining safety under service load conditions, the Factored load combinations as specified
in BS EN shall be used. Various load combinations as per the partial safety factors given in BS
EN are listed below for strength and serviceability criteria.
LOAD COMBINATIONS
4. 1.0 DL + 0.7 LL + 1 WL
Abbreviations; DL=dead load, LL=Live load, WL= wind load, EL= earthquake load
pg. 6
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
• The input file used for the design of plinth beam and pedestals in STAAD pro software
is attached in Annexure C.
pg. 7
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
ANNEXURE A
pg. 8
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Job Details
Job Name: mat for 940 941 942 859 860 887
Load Details
Included Loads
Load Case No 201: 1DL 0.3LL
Primary Serviceability Factor 1.000
Design Factor 1.000
Self-Weight Factor 1.000
Reactions
NODE NO. Fx (kN) Fy (kN) Fz (kN) Mx (kNm) My (kNm) Mz (kNm)
859 0.515 -228.709 2.966 -2.552 -0.462 -2.900
860 0.061 -260.417 -14.808 -12.395 -0.054 0.173
887 21.892 -257.889 21.466 5.950 0.323 -11.474
940 -3.086 -278.515 2.701 -3.879 0.257 6.952
941 -2.503 -267.908 -17.139 -14.618 0.142 3.833
942 -21.392 -274.931 19.922 4.247 -0.051 10.803
pg. 9
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Reactions
NODE NO. Fx (kN) Fy (kN) Fz (kN) Mx (kNm) My (kNm) Mz (kNm)
859 0.521 -228.022 2.983 -2.537 -0.470 -2.911
860 0.070 -259.707 -14.798 -12.385 -0.040 0.148
887 22.798 -257.009 21.473 5.958 0.334 -12.411
940 -2.042 -278.488 2.687 -3.891 0.285 5.230
941 -1.457 -267.920 -17.148 -14.626 0.120 2.098
942 -20.413 -275.785 19.913 4.240 -0.064 9.777
Reactions
NODE NO. Fx (kN) Fy (kN) Fz (kN) Mx (kNm) My (kNm) Mz (kNm)
859 0.507 -228.632 2.889 -2.626 -0.453 -2.887
860 0.068 -260.405 -14.865 -12.452 -0.049 0.158
887 22.278 -257.697 21.423 5.904 0.321 -11.873
940 -3.016 -278.535 2.739 -3.839 0.261 6.838
941 -2.489 -267.939 -17.102 -14.581 0.148 3.801
942 -20.887 -275.194 19.950 4.278 -0.052 10.284
Reactions
NODE NO. Fx (kN) Fy (kN) Fz (kN) Mx (kNm) My (kNm) Mz (kNm)
859 0.519 -228.528 2.972 -2.546 -0.467 -2.906
860 0.062 -260.216 -14.804 -12.391 -0.050 0.168
887 22.116 -257.889 21.467 5.953 0.322 -11.705
940 -2.822 -278.544 2.760 -3.819 0.273 6.517
941 -2.233 -267.972 -17.089 -14.568 0.138 3.383
942 -20.982 -274.962 19.958 4.287 -0.055 10.381
pg. 10
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Reactions
NODE NO. Fx (kN) Fy (kN) Fz (kN) Mx (kNm) My (kNm) Mz (kNm)
859 0.545 -248.492 3.031 -2.476 -0.505 -2.959
860 0.109 -291.252 -14.748 -12.331 0.016 0.045
887 26.438 -282.482 21.531 6.012 0.379 -16.180
940 1.288 -317.088 2.588 -3.961 0.369 -0.264
941 1.966 -306.697 -17.179 -14.660 0.061 -3.586
942 -16.839 -314.409 19.884 4.207 -0.101 5.943
Reactions
NODE NO. Fx (kN) Fy (kN) Fz (kN) Mx (kNm) My (kNm) Mz (kNm)
859 0.475 -251.541 2.562 -2.922 -0.421 -2.838
860 0.097 -294.743 -15.082 -12.664 -0.026 0.095
887 23.836 -285.920 21.283 5.744 0.316 -13.492
940 -3.582 -317.323 2.847 -3.705 0.247 7.776
941 -3.193 -306.791 -16.947 -14.432 0.196 4.934
942 -19.208 -311.454 20.065 4.399 -0.038 8.474
pg. 11
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Reactions
NODE NO. Fx (kN) Fy (kN) Fz (kN) Mx (kNm) My (kNm) Mz (kNm)
859 0.519 -256.207 3.031 -2.452 -0.456 -2.894
860 -0.043 -299.067 -14.716 -12.296 -0.174 0.426
887 13.797 -297.723 21.548 6.038 0.239 -3.106
940 -10.327 -317.662 2.571 -3.985 0.028 18.902
941 -9.938 -307.408 -17.192 -14.685 0.291 16.155
942 -28.493 -299.843 19.885 4.189 0.064 18.209
Reactions
NODE NO. Fx (kN) Fy (kN) Fz (kN) Mx (kNm) My (kNm) Mz (kNm)
859 0.536 -251.023 2.975 -2.524 -0.487 -2.935
860 0.070 -293.799 -14.777 -12.360 -0.033 0.144
887 23.026 -286.878 21.503 5.987 0.320 -12.654
940 -2.614 -317.367 2.954 -3.605 0.308 6.169
941 -1.913 -306.960 -16.882 -14.369 0.150 2.844
942 -19.682 -310.297 20.108 4.447 -0.053 8.959
Reactions
NODE NO. Fx (kN) Fy (kN) Fz (kN) Mx (kNm) My (kNm) Mz (kNm)
859 0.515 -240.319 2.955 -2.552 -0.462 -2.902
860 0.061 -277.610 -14.802 -12.387 -0.054 0.172
887 21.900 -272.385 21.481 5.963 0.322 -11.486
940 -3.510 -297.869 2.681 -3.891 0.243 7.647
941 -2.885 -287.274 -17.137 -14.618 0.156 4.463
942 -21.564 -292.537 19.923 4.247 -0.043 10.936
pg. 12
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Reactions
NODE NO. Fx (kN) Fy (kN) Fz (kN) Mx (kNm) My (kNm) Mz (kNm)
859 0.532 -267.626 2.972 -2.514 -0.484 -2.934
860 0.086 -318.818 -14.763 -12.343 -0.019 0.106
887 24.185 -306.425 21.536 6.012 0.350 -13.856
940 -1.958 -346.186 2.594 -3.950 0.278 5.082
941 -1.223 -335.717 -17.153 -14.638 0.136 1.699
942 -19.545 -338.685 19.906 4.226 -0.056 8.706
Reactions
NODE NO. Fx (kN) Fy (kN) Fz (kN) Mx (kNm) My (kNm) Mz (kNm)
859 0.496 -269.150 2.738 -2.737 -0.442 -2.874
860 0.081 -320.563 -14.930 -12.510 -0.039 0.130
887 22.884 -308.144 21.412 5.877 0.318 -12.513
940 -4.393 -346.304 2.724 -3.822 0.217 9.102
941 -3.802 -335.764 -17.037 -14.525 0.204 5.958
942 -20.729 -337.207 19.997 4.322 -0.025 9.971
pg. 13
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Reactions
NODE NO. Fx (kN) Fy (kN) Fz (kN) Mx (kNm) My (kNm) Mz (kNm)
859 0.518 -271.483 2.972 -2.502 -0.459 -2.902
860 0.010 -322.725 -14.747 -12.326 -0.113 0.296
887 17.865 -314.046 21.544 6.025 0.280 -7.320
940 -7.765 -346.473 2.585 -3.962 0.108 14.665
941 -7.175 -336.073 -17.159 -14.651 0.252 11.569
942 -25.372 -331.402 19.907 4.217 0.026 14.839
Reactions
NODE NO. Fx (kN) Fy (kN) Fz (kN) Mx (kNm) My (kNm) Mz (kNm)
859 0.527 -268.891 2.944 -2.538 -0.475 -2.923
860 0.067 -320.091 -14.778 -12.358 -0.043 0.155
887 22.479 -308.623 21.522 5.999 0.320 -12.094
940 -3.909 -346.326 2.777 -3.772 0.248 8.299
941 -3.163 -335.849 -17.004 -14.493 0.181 4.913
942 -20.967 -336.629 20.019 4.346 -0.032 10.214
Properties Details
Region Thickness(m) Material
MAT 0.500 Concrete
Soil Details
Boundary Subgrade Modulus Soil Height Above Soil Density Applied Load due
Mat to Soil
MAT 1288.000kN/m2/m 1.500m 15.000kN/m3 0.000kN/m^2
pg. 14
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Mat Dimension
Analysis Results
pg. 15
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Max 1 201 5.80025 1.67251 0.000 0.000 0.000 0.79289 0.59824 -0.36395
SX
Max 1 201 5.80025 1.67251 0.000 0.000 0.000 0.79289 0.59824 -0.36395
SY
Max 1 201 5.80025 1.67251 0.000 0.000 0.000 0.79289 0.59824 -0.36395
SXY
Max 598 213 239.36597 -418.2530 0.000 0.000 0.000 72.76048 56.45206 -7.89711
MX
Max 598 211 219.39359 -419.2317 0.000 0.000 0.000 71.62391 57.52705 -5.88461
MY
Max 640 208 -230.5846 229.57152 0.000 0.000 0.000 28.27979 21.26495 17.03884
MXY
Min 607 211 -367.4938 264.60252 0.000 0.000 0.000 51.59710 47.07331 5.66195
SQX
Min 565 213 206.33684 -470.7518 0.000 0.000 0.000 69.93867 45.62717 -2.60293
SQY
Min 1 201 5.80025 1.67251 0.000 0.000 0.000 0.79289 0.59824 -0.36395
SX
Min 1 201 5.80025 1.67251 0.000 0.000 0.000 0.79289 0.59824 -0.36395
SY
Min 1 201 5.80025 1.67251 0.000 0.000 0.000 0.79289 0.59824 -0.36395
SXY
Min 796 213 -10.05601 -25.19617 0.000 0.000 0.000 -0.18826 -21.7069 1.55643
MX
Min 589 211 -7.44436 4.75934 0.000 0.000 0.000 10.79151 -65.7669 0.93722
MY
Min 210 206 214.01365 213.80224 0.000 0.000 0.000 26.88343 18.50678 -16.1378
MXY
Minimum
Base Pressure 106 13.120 -2.100 4.244 202 18.03614
Contact Area
2
Load Case Area in Contact(m ) % of Total Area Area out of Contact(m2) % of Total
Area
201 74.62000 100.00000 0.00000 0.00000
pg. 16
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
pg. 17
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Design Parameters
Min Max Pedestal Pedestal Wood and
Panel Fc Top Bottom Pedestal Min Max
Bar Bar Min Bar Max Bar Armor
Name Fy (kN/m2) (kN/m2) Cover Cover Cover(m) Spacing Spacing
Size Size Size Size Moment
(m) (m) (mm) (mm)
(mm) (mm) (mm) (mm)
Not
MAT 500000.084 25000.004 0.075 0.075 0.040 12 16 12 50 100.000 200.000
Used
Design Output
Top of Mat Longitudinal Direction
Zone: - 1
For FC <4.0
Reinforcement Details
Bar No = N/A
Maximum Spacing (Smax) (User Specified) = 250.000(mm)
Minimum Spacing (Smin) (User Specified) = 100.000(mm)
Actual Spacing (S) = N/A
Smin<= S <= Smax
pg. 18
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
---------------------------------------
Zone: - 2
For FC <4.0
Reinforcement Details
Bar No = N/A
Maximum Spacing (Smax) (User Specified) = 250.000(mm)
Minimum Spacing (Smin) (User Specified) = 100.000(mm)
Actual Spacing (S) = N/A
Smin<= S <= Smax
---------------------------------------
Top of Mat Transverse Direction
Zone: - 1
For FC <4.0
pg. 19
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
For FC <4.0
pg. 20
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Reinforcement Details
Bar No = 12
Maximum Spacing (Smax) (User Specified) = 250.000(mm)
For FC <4.0
Reinforcement Details
Bar No = N/A
Maximum Spacing (Smax) (User Specified) = 250.000(mm)
Minimum Spacing (Smin) (User Specified) = 100.000(mm)
Actual Spacing (S) = N/A
Smin<= S <= Smax
---------------------------------------
pg. 21
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Zone: - 1
For FC <4.0
Steel Required
Reinforcement Details
Bar No = N/A
---------------------------------------
Zone: - 2
For FC <4.0
pg. 22
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Reinforcement Details
Bar No = 14
Maximum Spacing (Smax) (User Specified) = 250.000(mm)
Minimum Spacing (Smin) (User Specified) = 100.000(mm)
Actual Spacing (S) = 130(mm)
Smin<= S <= Smax
---------------------------------------
Zone: - 3
For FC <4.0
pg. 23
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Reinforcement Details
Bar No = 16
Zone: - 1
For FC <4.0
Reinforcement Details
Bar No = N/A
Maximum Spacing (Smax) (User Specified) = 250.000(mm)
Minimum Spacing (Smin) (User Specified) = 100.000(mm)
pg. 24
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Zone: - 2
For FC <4.0
Reinforcement Details
Bar No= 14
Maximum Spacing (Smax) (User Specified) = 250.000(mm)
Minimum Spacing (S min) (User Specified) = 100.000(mm)
Actual Spacing (S) = 100(mm)
Smin<= S <= Smax
---------------------------------------
Zone: - 3
Governing Moment (MGOV)= -127.037(kN-m/m)
pg. 25
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
For FC <4.0
Reinforcement Details
Bar No = N/A
Maximum Spacing (Smax) (User Specified) = 250.000(mm)
Minimum Spacing (Smin) (User Specified) = 100.000(mm)
Actual Spacing (S) = N/A
Smin<= S <= Smax
---------------------------------------
pg. 26
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
EN-1992-1-1:2004(E)
Result Summary
Footing No. Left Overhang Right Overhang Length (m) Width (m) Thickness (m)
(m) (m)
1 Ø12.0 @ 110 mm c/c Ø12.0 @ 110 mm c/c Ø12 @ 110 mm c/c Ø12.0 @ 110 mm
c/c
pg. 27
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Combined Footing 1
Input Data
0.5 m 1.5 m 2.05 m 2.05 m
2.445 m 3.145 m 0.7 m 0.4 m 0.7 m 0.4 m 2.175 m 2.175 m 7.495 m 4.85 m
Geometry of Footing
1.For
1.For Column 924
Column Dimensions
Pedestal
Include Pedestal? No
Pedestal Shape: N/A
Pedestal Height (Ph): N/A
Pedestal Length - X (Pl): N/A
Pedestal Width - Z (Pw): N/A
Eccentricity
Column Dimensions
Column Shape: Rectangular
pg. 28
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Pedestal
Include Pedestal? No
Pedestal Shape: N/A
Pedestal Height (Ph): N/A
Pedestal Length - X (Pl): N/A
Pedestal Width - Z (Pw): N/A
Eccentricity
Column Offset in Transverse Direction: 0.000m
Length of left overhang: 1.000m
Length of right overhang: 1.000m
Is the length of left overhang fixed? No
Is the length of right overhang fixed? No
Minimum width of footing (Wo): 2.500m
Minimum Thickness of footing (Do): 500.000mm
Maximum Width of Footing (Wo): 40000.000mm
Maximum Thickness of Footing (Do): 1500.000mm
Maximum Length of Footing (Lo): 40000.000mm
Length Increment: 50.000mm
Depth Increment: 50.000mm
pg. 29
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Design Calculations
Footing Size Calculations
pg. 30
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
------------------------------------------------------
Load Combinations
Load Combination/s-
Combination/s- Service Stress Level
Load Combination Number Load Combination Title
201 1DL 0.3LL
202 1DL 0.3LL 0.2WL+X
203 1DL 0.3LL 0.2WL-X
204 1DL 0.3LL 0.2WL+Z
205 1DL 0.3LL 0.2WL-Z
206 1DL 0.7LL 1WL(X+CPI)
207 1DL 0.7LL 1WL(X-CPI)
208 1DL 0.7LL 1WL(Z+CPI)
209 1DL 0.7LL 1WL(Z-CPI)
210 1DL 0.5LL
211 1DL 1LL 0.5WL(X+CPI)
212 1DL 1LL 0.5WL(X-CPI)
213 1DL 1LL 0.5WL(Z+CPI)
214 1DL 1LL 0.5WL(Z-CPI)
Load Combination/s-
Combination/s- Strength Level
Load Combination Number Load Combination Title
201 1DL 0.3LL
202 1DL 0.3LL 0.2WL+X
pg. 31
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Applied Loads
-
Column Number: 924
201 197.803 -66.979 17.840 8.071 112.117
202 186.764 -57.196 17.734 7.956 95.609
203 184.283 -57.809 17.974 8.218 96.691
204 171.586 -48.435 16.902 7.058 80.916
205 178.456 -53.510 15.565 5.601 89.468
206 153.188 -25.424 17.751 8.001 41.955
207 140.782 -28.484 18.953 9.309 47.364
208 77.301 18.381 13.591 3.508 -31.511
209 111.648 -6.989 6.905 -3.778 11.252
210 203.094 -70.659 18.060 8.321 118.307
211 188.722 -55.400 18.346 8.662 92.511
212 182.519 -56.930 18.947 9.316 95.215
213 150.779 -33.497 16.266 6.416 55.777
214 167.952 -46.182 12.923 2.772 77.159
pg. 32
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
-
Column Number: 925
201 276.320 -37.551 -22.342 -12.051 17.007
202 266.319 -33.493 -22.475 -12.188 10.731
203 263.776 -35.862 -22.259 -11.946 14.283
204 259.936 -33.511 -23.551 -13.319 10.568
205 271.371 -36.428 -25.239 -15.143 15.067
206 246.414 -18.539 -22.425 -12.082 -12.328
207 233.699 -30.386 -21.345 -10.874 5.433
208 214.499 -18.631 -27.808 -17.739 -13.145
209 271.673 -33.217 -36.244 -26.860 9.351
210 286.370 -38.192 -22.052 -11.724 18.028
211 286.490 -29.646 -21.658 -11.250 4.892
212 280.133 -35.569 -21.118 -10.646 13.772
213 270.533 -29.692 -24.349 -14.078 4.484
214 299.120 -36.985 -28.568 -18.639 15.732
pg. 33
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Pressures at 4 Corners
Load Case Pressure at top left Pressure at top Pressure at bottom Pressure at Area of footing in uplift
corner (kN/m2) right corner right corner (kN/m2) bottom left corner (Au) (sq. m)
(kN/m2) (kN/m2)
209 51.3108 42.2230 44.9937 54.0815 0.000
pg. 34
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
If Au is zero, there is no uplift and no pressure adjustment is necessary. Otherwise, to account for uplift,
areas of negative pressure will be set to zero and the pressure will be redistributed to remaining corners.
Stability Check
Resisting
Load Shear X Shear Z Ratio X Ratio Z Required
Sliding Force
Case (kN) (kN) FOS
(kN)
201 104.531 4.502 736.469 7.045 163.573 1.500
2022
202 90.689 4.741 728.052 8.028 153.568 1.500
pg. 35
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Check for stability against overturning (Moments printed against Local axis)
Load Resisting Resisting
Case Moment X Moment Z Required
Moment X Moment Ratio Ratio
(kNm) (kNm) FOS
(kNm) Z (kNm) X Z
201 181.389 117.235 4464.759 6899.662 24.614 58.853 1.500
= 1.000
pg. 36
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
= 1.000
Depth of Neutral Axis(X) = 0.138m
Limit Moment of Resistance
pg. 37
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
For Column 1
Shear Force(S) = 192.315kN
Shear Stress (Tv) = 120.886kN/m2
EN 1992-1-1:2004(E) Clause No. 6.4
= 1.000
Shear Strength (Tc) = 2198.6096kN/m^2
X Tv<= Tc hence, safe
Critical Load case for Punching Shear Check: 214
For Column 2
Shear Force(S) = 286.322kN
Shear Stress (Tv)= 179.978kN/m2
EN 1992-1-1:2004(E) Clause No. 6.4
= 1.000
Shear Strength (Tc) = 2198.6096kN/m2
Selection of reinforcement
pg. 38
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Along width
EN 1992-1-1:2004(E) Clause No. 3.1.7,3.2.7
And Fig 3.8
Provided Minimum Area of Steel (Ast min)= 7494.997mm2
Selected bar Size (db) = Ø12
Minimum spacing allowed (Smin) = 100.000mm
Selected spacing (S) = 111.106mm
Smin<= S <= Smax and selected bar size < selected maximum bar size... The reinforcement
is accepted.
pg. 39
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Along width
EN 1992-1-1:2004(E) Clause No. 3.1.7,3.2.7
And Fig 3.8
pg. 40
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Ø12.0 @ 110mm
pg. 41
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
EN-1992-1-1:2004(E)
Result Summary
Combined Footing 1
Input Data
0.5m 0m 0.4m 0.4m
2m 2.46m 0.46m 0.34m 0.46m 0.34m 1m 1m 4.46m 2.5 m
Geometry of Footing
1.For
1.For Column 938
Column Dimensions
Column Shape: Rectangular
Column Length - X (Pl): 0.460m
Column Width - Z (Pw): 0.340m
Pedestal
Include Pedestal? No
pg. 42
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Eccentricity
Column Offset in Transverse Direction:0.000m
Column Dimensions
Column Shape: Rectangular
Column Length - X (Pl): 0.460m
Column Width - Z (Pw): 0.340m
Pedestal
Include Pedestal? No
Pedestal Shape: N/A
Pedestal Height (Ph): N/A
Pedestal Length - X (Pl): N/A
Pedestal Width - Z (Pw): N/A
Eccentricity
Column Offset in Transverse Direction: 0.000m
Column Dimensions
pg. 43
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Pedestal
Include Pedestal? No
Pedestal Shape: N/A
Pedestal Height (Ph): N/A
Pedestal Length - X (Pl): N/A
Pedestal Width - Z (Pw): N/A
Eccentricity
Column Offset in Transverse Direction: 0.000m
Length of left overhang: 1.000m
Length of right overhang: 1.000m
Is the length of left overhang fixed?
No Is the length of right overhang fixed? No
Minimum width of footing (Wo): 2.500m
Minimum Thickness of footing (Do): 500.000mm
Maximum Width of Footing (Wo): 40000.000mm
Maximum Thickness of Footing (Do): 1500.000mm
Maximum Length of Footing (Lo): 40000.000mm
Length Increment: 50.000mm Depth Increment: 50.000mm
pg. 44
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
-----------------------------------------------------
pg. 45
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Load Combinations
Load Combination/s- Service Stress Level
Load Combination Number Load Combination Title
201 1DL 0.3LL
202 1DL 0.3LL 0.2WL+X
203 1DL 0.3LL 0.2WL-X
204 1DL 0.3LL 0.2WL+Z
205 1DL 0.3LL 0.2WL-Z
206 1DL 0.7LL 1WL(X+CPI)
207 1DL 0.7LL 1WL(X-CPI)
208 1DL 0.7LL 1WL(Z+CPI)
209 1DL 0.7LL 1WL(Z-CPI)
210 1DL 0.5LL
211 1DL 1LL 0.5WL(X+CPI)
212 1DL 1LL 0.5WL(X-CPI)
213 1DL 1LL 0.5WL(Z+CPI)
214 1DL 1LL 0.5WL(Z-CPI)
pg. 46
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Applied Loads -
LC Axial Shear X Shear Z Moment Moment Z
(kN) (kN) (kN) X (kNm) (kNm)
-
Column Number: 938
201 186.568 10.891 1.785 6.966 -2.860
pg. 47
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
pg. 48
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Pressures at 4 Corners
Pressure at Pressure at
Pressure at Pressure at Area of footing
bottom right bottom left
Load top left corner top right in uplift (Au)
corner corner
Case (kN/m2) corner (sq. m)
(kN/m2) (kN/m2)
(kN/m2)
214 57.6429 26.3441 28.1663 59.4652 0.000
If Au is zero, there is no uplift and no pressure adjustment is necessary. Otherwise, to account for uplift,
areas of negative pressure will be set to zero and the pressure will be redistributed to remaining corners.
pg. 49
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Stability Check
Resisting Sliding
Shear X Shear Y
Load Case Ratio X Ratio Z Required FOS
Force (kN)
(kN) (kN)
201 11.900 18.145 172.105 14.462 9.485 1.500
Check for stability against overturning (Moments printed against Local axis)
Resisting Resisting
Moment X Moment Z Required
Load Case Moment X Moment Z Ratio X Ratio Z
(kNm) (kNm) FOS
(kNm) (kNm)
201 5.073 94.694 537.817 959.466 106.008 10.132 1.500
pg. 50
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
= 0.800
= 1.000
Depth of Neutral Axis(X) = 0.138m
pg. 51
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
= 0.800
= 1.000
Depth of Neutral Axis(X) = 0.138m
Transverse direction
Critical load case: 213
= 0.800
= 1.000
Depth of Neutral Axis(X) = 0.138m
pg. 52
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
= 1.000
Shear Strength (Tc) = 2219.5657 kN/m2
For Column 2
Shear Force(S) = 119.238kN
Shear Stress (Tv) = 88.780kN/m2
EN 1992-1-1:2004(E) Clause No. 6.4
= 1.000
Shear Strength (Tc) = 2219.5657kN/m2
pg. 53
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Along width
EN 1992-1-1:2004(E) Clause No. 3.1.7,3.2.7 And Fig 3.8
Provided Minimum Area of Steel (Ast min) = 4460.000mm2
Selected bar Size (db) = Ø12
Minimum spacing allowed (Smin) = 100.000mm
Selected spacing (S) = 110.205mm
Smin<= S <= Smax and selected bar size < selected maximum bar size... The reinforcement
is accepted.
pg. 54
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Along width
EN 1992-1-1:2004(E) Clause No. 3.1.7,3.2.7 And Fig 3.8
Minimum Area of Steel (A st min) = 4460.000mm2
Calculated Area of Steel (Ast) = 4460.000mm2
Provided Area of Steel (Ast, Provided) = 4521.617mm2
A st min<= Ast, Provided Steel area is accepted
Selected bar Size (db) = Ø12
Minimum spacing allowed (Smin) = 100.000mm
Selected spacing (S) = 110.205mm
S min<= S <= S max and selected bar size < selected maximum bar size... The reinforcement
is accepted.
Provided Reinforcement
Main bar no. for top Reinforcement: Ø12.0
Spacing of top reinforcement bar : 106.273mm
pg. 55
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
pg. 56
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Combined Footing 2
Input Data
Geometry of Footing
Column Dimensions
Pedestal
Include Pedestal? No
Eccentricity
Column Dimensions
pg. 57
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Pedestal
Include Pedestal? No
Eccentricity
Is the length of left overhang fixed? No Is the length of right overhang fixed? No
Minimum width of footing (Wo): 2.500m Minimum Thickness of footing (Do): 500.000mm
Maximum Width of Footing (Wo): 40000.000mm Maximum Thickness of Footing (Do): 1500.000mm
pg. 58
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
-------------------------
Design Calculations
Reduction of force due to buoyancy Area from initial length and width, A o
pg. 59
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Load Combinations
Load Combination/s- Service Stress Level
Load Combination Number Load Combination Title
201 1DL 0.3LL
202 1DL 0.3LL 0.2WL+X
203 1DL 0.3LL 0.2WL-X
204 1DL 0.3LL 0.2WL+Z
205 1DL 0.3LL 0.2WL-Z
206 1DL 0.7LL 1WL(X+CPI)
207 1DL 0.7LL 1WL(X-CPI)
208 1DL 0.7LL 1WL(Z+CPI)
209 1DL 0.7LL 1WL(Z-CPI)
210 1DL 0.5LL
211 1DL 1LL 0.5WL(X+CPI)
212 1DL 1LL 0.5WL(X-CPI)
213 1DL 1LL 0.5WL(Z+CPI)
214 1DL 1LL 0.5WL(Z-CPI)
pg. 60
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
pg. 61
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Pressures at 4 Corners
Pressure at Pressure at
Pressure at top Pressure at top Area of footing
bottom right bottom left
Load Case left corner right corner in uplift (Au)
corner (kN/m2) corner
(kN/m2) (kN/m2) (sq. m)
(kN/m2)
214 57.6429 26.3441 28.1663 59.4652 0.000
If Au is zero, there is no uplift and no pressure adjustment is necessary. Otherwise, to account for uplift,
areas of negative pressure will be set to zero and the pressure will be redistributed to remaining corners.
pg. 62
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Stability Check
Resisting
Load Shear Shear Ratio X Ratio Z Required
Sliding
Case X Z FOS
Force (kN)
(kN) (kN)
check for stability against overturning (Moments printed against Local axis)
Resisting Resisting
Moment Moment Required
Load Case Moment X Moment Z Ratio X Ratio Z
X (kNm) Z (kNm) FOS
(kNm) (kNm)
201 5.073 94.694 537.817 959.466 106.008 10.132 1.500
pg. 63
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
------------------------------------------------------
Position [m]Moment[kNm]00.71.42.12.83.54.24.46-1000100
= 0.800
= 1.000
Depth of Neutral Axis(X) = 0.138m
pg. 64
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Transverse direction
Critical load case: 213
= 1.000
Depth of Neutral Axis(X) = 0.138m
pg. 65
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
= 1.000
Shear Strength (Tc) = 2219.5657 kN/m2
= 1.000
Shear Strength (Tc) = 2219.5657 kN/m2
pg. 66
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Along width
EN 1992-1-1:2004(E) Clause No. 3.1.7,3.2.7 and Fig 3.8
Provided Minimum Area of Steel (A st min) = 4460.000 mm2
Selected bar Size (db) = Ø12
Minimum spacing allowed (Smin) = 100.000 mm
Selected spacing (S) = 110.205 mm
Smin<= S <= Smax and selected bar size < selected maximum bar size... The reinforcement
is accepted.
pg. 67
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Smin<= S <= Smax and selected bar size < selected maximum bar size... The reinforcement
is accepted.
Along width
EN 1992-1-1:2004(E) Clause No. 3.1.7,3.2.7 and Fig 3.8
Minimum Area of Steel (Astmin) = 4460.000 mm2
Calculated Area of Steel (Ast) = 4460.000 mm2
Provided Area of Steel (Ast, Provided) = 4521.617 mm2
Astmin<= Ast, Provided Steel area is accepted
Selected bar Size (db) = Ø12
Minimum spacing allowed (Smin) = = 100.000 mm
Provided Reinforcement
Main bar no. for top Reinforcement: Ø12.0
Spacing of top reinforcement bar: 106.273 mm
Based on spacing reinforcement increment; provided reinforcement is
pg. 68
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
------------------------------------------------------
pg. 69
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Input Values
Footing Geometry
Column Dimensions
Pedestal
Include Pedestal? No
Design Parameters
pg. 70
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Soil Properties
Global Settings
Top Reinforcement Option: Calculate only when foundation is subjected to uplift forces
Concrete Design Option: Net Pressure (Gross Pressure - Self Weight Pressure)
pg. 71
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Load Combinations
Load Combination/s- Service Stress Level
Load
Combination Load Combination Title
Number
201 1DL 0.3LL
202 1DL 0.3LL 0.2WL+X
203 1DL 0.3LL 0.2WL-X
204 1DL 0.3LL 0.2WL+Z
205 1DL 0.3LL 0.2WL-Z
206 1DL 0.7LL 1WL(X+CPI)
207 1DL 0.7LL 1WL(X-CPI)
208 1DL 0.7LL 1WL(Z+CPI)
209 1DL 0.7LL 1WL(Z-CPI)
210 1DL 0.5LL
211 1DL 1LL 0.5WL(X+CPI)
212 1DL 1LL 0.5WL(X-CPI)
213 1DL 1LL 0.5WL(Z+CPI)
214 1DL 1LL 0.5WL(Z-CPI)
Load
Combination Load Combination Title
Number
201 1DL 0.3LL
202 1DL 0.3LL 0.2WL+X
203 1DL 0.3LL 0.2WL-X
204 1DL 0.3LL 0.2WL+Z
205 1DL 0.3LL 0.2WL-Z
206 1DL 0.7LL 1WL(X+CPI)
207 1DL 0.7LL 1WL(X-CPI)
208 1DL 0.7LL 1WL(Z+CPI)
209 1DL 0.7LL 1WL(Z-CPI)
pg. 72
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Applied Loads
pg. 73
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Design Calculations
Footing Size
Initial Length (Lo) = 1.000m
Initial Width (Wo) = 1.000m
Uplift force due to buoyancy = 0.000kN
Effect due to adhesion = 0.000kN
Area from initial length and width, A o = Lo X Wo = 1.000m2
Min. area required from bearing pressure, Amin = P / q max = 6.309m2
pg. 74
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Pressures at 4 Corners
If Au is zero, there is no uplift and no pressure adjustment is necessary. Otherwise, to account for uplift, areas
of negative pressure will be set to zero and the pressure will be redistributed to remaining corners.
Pressure at Pressure at
Pressure at top Pressure at top
bottom right bottom left
Load Case left corner right corner
corner corner
(kN/m2) (kN/m2) (kN/m2) (kN/m2)
213 59.8699 59.9894 59.2812 59.1616
Details of Out-
Out-of-
of-Contact Area (If Any)
Governing load case = N/A
pg. 75
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Stability Check
0.3m 1.2m. Frictional Force Sliding Force OTM
Load
Along X- Along Z- Resultant Required W.R.T. X- W.R.T. Z- Required
Case
Direction Direction FOS Direction Direction FOS
No.
pg. 76
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Critical Load Case and The Governing Factor of Safety for Overturning and Sliding X Direction
Critical Load Case for Sliding along X-Direction: 206
Governing Disturbing Force: 6.410kN
Critical Load Case and The Governing Factor of Safety for Overturning and Sliding Z Direction
Critical Load Case for Sliding along Z-Direction: 208
Governing Disturbing Force: -4.712kN
Governing Restoring Force: 316.041kN
Minimum Sliding Ratio for the Critical Load Case: 67.071
Critical Load Case for Overturning w.r.t. Z-Direction: 206
Governing Overturning Moment: -4.500kNm
Governing Resisting Moment: 1104.933kNm
Minimum Overturning Ratio for the Critical Load Case: 245.561
Critical Load Case and The Governing Factor of Safety for Sliding Along Resultant Direction
Critical Load Case for Sliding along Resultant Direction: 206
Governing Disturbing Force: 6.443kN
Governing Restoring Force: 323.258kN
Minimum Sliding Ratio for the Critical Load Case: 50.169
pg. 77
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Moment Calculation
Check Trial Depth against moment (w.r.t. X Axis)
Critical Load Case = #211
= 0.800000
= 1.000000
Depth of Neutral Axis(X) = 0.070003m
= 0.800000
= 1.000000
Depth of Neutral Axis(X) = 0.070003m
pg. 78
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
One-
One-Way Shear Along Z
(Shear Plane Parallel to Global Z Axis)
1.7m 1.7m1.293m 1.293m PlanXZ
hence, safe
One-
One-Way Shear Along X
(Shear Plane Parallel to Global X Axis)
1.7m 1.7m 1.193m 1.193m PlanXZ
hence, safe
pg. 79
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
hence, safe
Reinforcement Calculation
Calculation of Maximum Bar Size
Along X Axis
Bar diameter corresponding to max bar size (d b) = 16mm
As Per EN-1992-1-1:2004 Clause No.8.4.3,8.4.4 and Table 8.2
Development Length (l d) = 0.162m
Along Z Axis
Bar diameter corresponding to max bar size(db) = 16mm
As Per EN-1992-1-1:2004 Clause No.8.4.3,8.4.4 and Table 8.2
Development Length(ld) = 0.162m
pg. 80
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Flexure About X-
X-Axis
Flexure About Z-
Z-Axis
pg. 81
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
pg. 82
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Input Values
Footing Geometry
Design Type: Calculate Dimension
Footing Thickness (Ft): 300.000mm
Footing Length - X (Fl): 1000.000mm
Footing Width - Z (Fw): 1000.000mm
Eccentricity along X (Oxd): 0.000mm
Eccentricity along Z (Ozd): 0.000mm
Column Dimensions
Column Shape: Rectangular
Column Length - X (Pl): 0.700m
Column Width - Z (Pw): 0.400m
Pedestal
Include Pedestal? No
Pedestal Shape: N/A
Pedestal Height (Ph): N/A
Pedestal Length - X (Pl): N/A
Pedestal Width - Z (Pw): N/A
pg. 83
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Design Parameters
Soil Properties
Soil Type: Cohesionless Soil
Unit Weight: 18.000kN/m3
Soil Bearing Capacity: 61.600kN/m2
Soil Bearing Capacity Type: Gross Bearing Capacity
Soil Surcharge: 0.000kN/m2
Depth of Soil above Footing: 1200.000mm
Type of Depth: Fixed Bottom
Undrained Shear Strength: 0.000kN/m2
Min Percentage of Slab in Contact: 100.000
pg. 84
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Global Settings
Top Reinforcement Option: Calculate only when foundation is subjected to uplift forces
Concrete Design Option: Net Pressure (Gross Pressure - Self Weight Pressure)
Load Combinations
Load Combination/s- Service Stress Level
Load
Combination Load Combination Title
Number
pg. 85
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Applied Loads
pg. 86
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Design Calculations
Footing Size
Initial Length (Lo) = 1.000m
Initial Width (Wo) = 1.000m
Uplift force due to buoyancy = 0.000kN
Effect due to adhesion = 0.000kN
Area from initial length and width, A o = Lo X Wo = 1.000m2
Min. area required from bearing pressure, Amin = P / q max = 15.158m2
pg. 87
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Pressures at 4 Corners
pg. 88
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Pressure at Pressure at
Pressure at top Pressure at bottom right bottom left
Load Case left corner top right corner corner corner
(kN/m2) (kN/m2) (kN/m2) (kN/m2)
Details of Out-
Out-of-
of-Contact Area (If Any)
Stability Check
0.35m 1. 15m.Frictional Force Sliding Force OTM
Load
Case Along X- Along Z- Resultant Required W.R.T. X- W.R.T. Z- Required
No. Direction Direction FOS Direction Direction FOS
pg. 89
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Critical Load Case and The Governing Factor of Safety for Overturning and Sliding X Direction
Critical Load Case for Sliding along X-Direction: 210
Governing Disturbing Force: -84.794kN
Governing Restoring Force: 467.578kN
Minimum Sliding Ratio for the Critical Load Case: 5.514
Critical Load Case for Overturning w.r.t. X-Direction: 208
Governing Overturning Moment: -11.606kNm
Governing Resisting Moment: 1749.892kNm
Minimum Overturning Ratio for the
Critical Load Case: 150.770
Critical Load Case and The Governing Factor of Safety for Overturning and Sliding Z Direction
Critical Load Case for Sliding along Z-Direction: 208
Governing Disturbing Force: -9.405kN
pg. 90
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
------------------------------------------------------
Moment Calculation
= 0.800000
= 1.000000
Depth of Neutral Axis(X) = 0.086912m
pg. 91
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
= 0.800000
= 1.000000
Depth of Neutral Axis(X) = 0.086912m
pg. 92
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
hence, safe
One-
One-Way Shear Along X
hence, safe
hence, safe
------------------------------------------------------
pg. 93
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Reinforcement Calculation
Along X Axis
Bar diameter corresponding to max bar size (db) = 16mm
As Per EN-1992-1-1:2004 Clause No.8.4.3,8.4.4 and Table 8.2
Development Length (l d) = 0.162m
Along Z Axis
Bar diameter corresponding to max bar size(db) = 16mm
As Per EN-1992-1-1:2004 Clause No.8.4.3,8.4.4 and Table 8.2
Development Length (l d) = 0.162 m
Allowable Length (l db) = = 1.850 m
ldb >=l d hence, safe
pg. 94
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Flexure About Z-
Z-Axis
pg. 95
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
pg. 96
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Input Values
Footing Geometry
Design Type: Calculate Dimension
Footing Thickness (Ft): 300.000mm
Footing Length - X (Fl): 1000.000mm
Footing Width - Z (Fw): 1000.000mm
Eccentricity along X (Oxd): 0.000mm
Eccentricity along Z (Ozd): 0.000mm
Column Dimensions
Column Shape: Rectangular
Column Length - X (Pl): 0.700m
Column Width - Z (Pw): 0.400m
Pedestal
Include Pedestal? No
Pedestal Shape: N/A
Pedestal Height (Ph): N/A
Pedestal Length - X (Pl): N/A
Pedestal Width - Z (Pw): N/A
Design Parameters
pg. 97
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Soil Properties
Soil Type: Cohesionless Soil
Unit Weight: 18.000kN/m3
Soil Bearing Capacity: 61.600kN/m2
Soil Bearing Capacity Type: Gross Bearing Capacity
Soil Surcharge: 0.000kN/m2
Depth of Soil above Footing: 1200.000mm
Type of Depth: Fixed Bottom
Undrained Shear Strength: 0.000kN/m2
Min Percentage of Slab in Contact: 100.000
Global Settings
Top Reinforcement Option: Calculate only when foundation is subjected to uplift forces
pg. 98
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Concrete Design Option: Net Pressure (Gross Pressure - Self Weight Pressure)
Load Combinations
Load Combination/s- Service Stress Level
Load
Combination Load Combination Title
Number
201 1DL 0.3LL
202 1DL 0.3LL 0.2WL+X
203 1DL 0.3LL 0.2WL-X
204 1DL 0.3LL 0.2WL+Z
205 1DL 0.3LL 0.2WL-Z
206 1DL 0.7LL 1WL(X+CPI)
207 1DL 0.7LL 1WL(X-CPI)
208 1DL 0.7LL 1WL(Z+CPI)
209 1DL 0.7LL 1WL(Z-CPI)
210 1DL 0.5LL
211 1DL 1LL 0.5WL(X+CPI)
212 1DL 1LL 0.5WL(X-CPI)
213 1DL 1LL 0.5WL(Z+CPI)
214 1DL 1LL 0.5WL(Z-CPI)
Load Combination/s- Strength Level
Load
Combination Load Combination Title
Number
201 1DL 0.3LL
202 1DL 0.3LL 0.2WL+X
203 1DL 0.3LL 0.2WL-X
204 1DL 0.3LL 0.2WL+Z
205 1DL 0.3LL 0.2WL-Z
206 1DL 0.7LL 1WL(X+CPI)
207 1DL 0.7LL 1WL(X-CPI)
208 1DL 0.7LL 1WL(Z+CPI)
pg. 99
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Applied Loads
pg. 100
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Design Calculations
Footing Size
Initial Length (Lo) = 1.000m
Initial Width (Wo) = 1.000m
Uplift force due to buoyancy = 0.000kN
Effect due to adhesion = 0.000kN
Area from initial length and width, A o = Lo X Wo = 1.000m2
Min. area required from bearing pressure, Amin = P / q max = 4.225m2
Final Footing
Footing Size
Length (L2) = 3.800 m Governing Load Case: # 210
Width (W2) = 3.800 m Governing Load Case: # 210
Depth (D2) = 0.300 m
pg. 101
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Pressures at 4 Corners
If Au is zero, there is no uplift and no pressure adjustment is necessary. Otherwise, to account for
uplift, areas of negative pressure will be set to zero and the pressure will be redistributed to remaining
corners.
Summary of adjusted
adjusted Pressures at Four Corner
Pressure at Pressure at
Pressure at top Pressure at top
bottom right bottom left
Load left corner right corner
corner (kN/m2) corner
Case (kN/m2) (kN/m2) (kN/m2)
Details of Out-
Out-of-
of-Contact Area (If Any)
Governing load case = N/A
pg. 102
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
------------------------------------------------------
Stability Check
0.3m 1.2m. Frictional Force Sliding Force OTM
Load
Along X- Along Z- Resultant Required W.R.T. X- W.R.T. Z- Required
Case
Direction Direction FOS Direction Direction FOS
No.
pg. 103
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Critical Load Case and The Governing Factor of Safety for Overturning and Sliding X Direction
Critical Load Case for Sliding along X-Direction: 210
Governing Disturbing Force: -70.013kN
Critical Load Case and The Governing Factor of Safety for Overturning and Sliding Z Direction
Critical Load Case for Sliding along Z-Direction: 209
Governing Disturbing Force: -9.369kN
Governing Restoring Force: 258.573kN
Minimum Sliding Ratio for the Critical Load Case: 27.599
Critical Load Case for Overturning w.r.t. Z-Direction: 210
Governing Overturning Moment: 140.045kNm
Governing Resisting Moment: 1239.052kNm
Minimum Overturning Ratio for the Critical Load Case: 8.848
Critical Load Case and The Governing Factor Of Safety For Sliding Along Resultant Direction
Critical Load Case for Sliding along Resultant Direction: 210
Governing Disturbing Force: 70.018kN
Governing Restoring Force: 325.694kN
Minimum Sliding Ratio for the Critical Load Case: 4.652
pg. 104
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Moment Calculation
= 0.800000
= 1.000000
Depth of Neutral Axis(X) = 0.070003m
= 0.800000
= 1.000000
Depth of Neutral Axis(X) = 0.070003m
pg. 105
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
One-
One-Way Shear Along Z
hence, safe
One-
One-Way Shear Along X
hence, safe
pg. 106
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
hence, safe
Reinforcement Calculation
Along X Axis
Bar diameter corresponding to max bar size (db) = 16mm
As Per EN-1992-1-1:2004 Clause No.8.4.3,8.4.4 and Table 8.2
Development Length(ld) = 0.162m
Along Z Axis
Bar diameter corresponding to max bar size(db) = 16mm
As Per EN-1992-1-1:2004 Clause No.8.4.3,8.4.4 and Table 8.2
Development Length (l d) = 0.162m
pg. 107
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
22 - ϕ12XZ
For moment w.r.t. X Axis (Mx)
As Per EN-1992-1-1: 2004 Clause No. 3.1.7(3),3.2.7 and Fig.3.5,3.8
Critical Load Case = #210
Minimum Area of Steel (A st min) = 2280.000mm2
Calculated Area of Steel (A st) = 2280.000mm2
Provided Area of Steel (A st, Provided) = 2486.889mm2
A st min<= A st, Provided Steel area is accepted
Selected bar Size (db) = Ø12
Minimum spacing allowed (S min) = 100.000mm
Selected spacing (S) = 180.460mm
S min<= S <= S max and selected bar size < selected maximum bar size...
The reinforcement is accepted.
pg. 108
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
pg. 109
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Input Values
Footing Geometry
Design Type: Calculate Dimension
Footing Thickness (Ft): 300.000mm
Footing Length - X (Fl): 1000.000mm
Footing Width - Z (Fw): 1000.000mm
Eccentricity along X (Oxd): 0.000mm
Eccentricity along Z (Ozd): 0.000mm
Column Dimensions
Column Shape: Rectangular
Column Length - X (Pl): 0.460m
Column Width - Z (Pw): 0.340m
Pedestal
Include Pedestal? No
Pedestal Shape: N/A
Pedestal Height (Ph): N/A
Pedestal Length - X (Pl): N/A
Pedestal Width - Z (Pw): N/A
Design Parameters
pg. 110
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Soil Properties
Soil Type: Cohesionless Soil
Unit Weight: 18.000kN/m3
Soil Bearing Capacity: 61.600kN/m2
Soil Bearing Capacity Type: Gross Bearing Capacity
Soil Surcharge: 0.000kN/m2
Depth of Soil above Footing: 1200.000mm
Type of Depth: Fixed Bottom
Undrained Shear Strength: 0.000kN/m2
Min Percentage of Slab in Contact: 100.000
Global Settings
Top Reinforcement Option: Calculate only when foundation is subjected to uplift forces
pg. 111
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Concrete Design Option: Net Pressure (Gross Pressure - Self Weight Pressure)
------------------------------------------------------
Load Combinations
Load Combination/s- Service Stress Level
Load Combination Number Load Combination Title
201 1DL 0.3LL
202 1DL 0.3LL 0.2WL+X
203 1DL 0.3LL 0.2WL-X
204 1DL 0.3LL 0.2WL+Z
205 1DL 0.3LL 0.2WL-Z
206 1DL 0.7LL 1WL(X+CPI)
207 1DL 0.7LL 1WL(X-CPI)
208 1DL 0.7LL 1WL(Z+CPI)
209 1DL 0.7LL 1WL(Z-CPI)
210 1DL 0.5LL
211 1DL 1LL 0.5WL(X+CPI)
212 1DL 1LL 0.5WL(X-CPI)
213 1DL 1LL 0.5WL(Z+CPI)
214 1DL 1LL 0.5WL(Z-CPI)
pg. 112
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Applied Loads
Before consideration of self-weight and load safety factor table
pg. 113
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Design Calculations
Footing Size
Initial Length (Lo) = 1.000m
Initial Width (Wo) = 1.000m
Uplift force due to buoyancy = 0.000kN
Effect due to adhesion = 0.000kN
Area from initial length and width, A o = Lo X Wo = 1.000m2
Min. area required from bearing pressure, Amin = P / q max = 18.186m2
pg. 114
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Pressures at 4 Corners
Pressure at Pressure at
Pressure at top Pressure at top bottom bottom left
Load Case left corner right corner right corner corner
(kN/m2)
(kN/m2) (kN/m2) (kN/m2)
------------------------------------------------------
pg. 115
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Stability Check
0.45 m 1.05 frictional Force Sliding ForceOTM
Load
Along X- Along Z- Resultant Required W.R.T. X- W.R.T. Z- Required
Case
Direction Direction FOS Direction Direction FOS
No.
critical Load Case and The Governing Factor of Safety for Overturning and Sliding X Direction
Critical Load Case for Sliding along X-Direction: 201
Governing Disturbing Force: -48.843kN
pg. 116
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Critical Load Case and The Governing Factor of Safety for Overturning and Sliding
Sliding Z Direction
Critical Load Case for Sliding along Z-Direction: 203
Governing Disturbing Force: 2.220kN
Governing Restoring Force: 487.507kN
Minimum Sliding Ratio for the Critical Load Case: 219.639
Critical Load Case for Overturning w.r.t. Z-Direction: 201
Governing Overturning Moment: 52.054kNm
Governing Resisting Moment: 2172.568kNm
Minimum Overturning Ratio for the Critical Load Case: 41.737
Critical Load Case and The Governing Factor Of Safety For Sliding Along Resultant Direction
Critical Load Case for Sliding along Resultant Direction: 201
Governing Disturbing Force: 48.893kN
Governing Restoring Force: 487.748kN
Minimum Sliding Ratio for the Critical Load Case: 9.976
Moment Calculation
pg. 117
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
= 0.800000
= 1.000000
Depth of Neutral Axis(X) = 0.120730m
= 0.800000
= 1.000000
Depth of Neutral Axis(X) = 0.120730m
One-
One-Way Shear Along Z
pg. 118
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
hence, safe
One-
One-Way Shear Along X
hence, safe
pg. 119
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
hence, safe
Reinforcement Calculation
pg. 120
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Flexure About Z-
Z-Axis
pg. 121
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
pg. 122
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
EN-1992-1-1: 2004
pg. 123
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
0.45m1.05m Elevation
2.55m1.75m 3.5m 5.1m 0.55m 0.23m XZ Plan
Input Values
Footing Geometry
Design Type: Calculate Dimension
Footing Thickness (Ft): 450.000mm
Footing Length - X (Fl): 5100.000mm
Footing Width - Z (Fw): 3200.000mm
Eccentricity along X (Oxd): 0.000mm
Eccentricity along Z (Ozd): 0.000mm
Column Dimensions
Column Shape: Rectangular
Column Length - X (Pl): 0.550m
Column Width - Z (Pw): 0.230m
Pedestal
Include Pedestal? No
Pedestal Shape: N/A
Pedestal Height (Ph): N/A
Pedestal Length - X (Pl): N/A
Pedestal Width - Z (Pw): N/A
pg. 124
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Design Parameters
Soil Properties
Soil Type: Cohesionless Soil
Unit Weight: 17.000kN/m3
Soil Bearing Capacity: 61.700kN/m2
Soil Bearing Capacity Type: Gross Bearing Capacity Soil Surcharge: 0.000kN/m2
Depth of Soil above Footing: 1050.000mm
Type of Depth: Fixed Bottom Undrained Shear Strength: 0.000kN/m2
Min Percentage of Slab in Contact: 100.000
pg. 125
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Global Settings
Top Reinforcement Option: Calculate only when foundation is subjected to uplift forces
Concrete Design Option: Net Pressure (Gross Pressure - Self Weight Pressure)
------------------------------------------------------
Load Combinations
pg. 126
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Applied Loads
pg. 127
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Axial Shear X
LC Shear Z Moment X Moment Z
(kN) (kN) (kN) (kNm) (kNm)
201 466.942 16.053 -3.956 -2.424 28.396
202 466.297 18.588 -4.133 -2.572 24.841
203 463.522 19.163 -2.865 -1.500 24.017
204 450.127 21.197 -3.915 -2.388 21.125
205 460.923 20.524 -4.083 -2.529 22.091
206 513.392 26.530 -4.971 -3.272 13.853
207 499.516 29.408 1.366 2.088 9.731
208 432.541 39.577 -3.883 -2.354 -4.729
209 486.524 36.212 -4.723 -3.055 0.101
210 491.780 14.954 -4.022 -2.478 30.011
211 552.262 18.545 -4.629 -2.984 25.163
212 545.324 19.983 -1.460 -0.303 23.101
213 511.837 25.068 -4.084 -2.525 15.871
214 538.828 23.385 -4.505 -2.875 18.286
------------------------------------------------------
Design Calculations
Footing Size
Initial Length (Lo) = 5.100m
Initial Width (Wo) = 3.200m
Uplift force due to buoyancy = 0.000kN
Effect due to adhesion = 0.000kN
Area from initial length and width, A o = Lo X Wo = 16.320m2
Min. area required from bearing pressure, Amin = P / q max = 16.611m2
pg. 128
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Pressures at 4 Corners
pg. 129
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Stability Check
0.45m 1. 05m.Frictional Force Sliding Force OTM
Load
Along X- Along Z- Resultant Required W.R.T. X- W.R.T. Z- Required
Case No.
Direction Direction FOS Direction Direction FOS
201 30.653 124.384 29.763 1.500 410.376 118.471 1.500
pg. 130
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Critical Load Case and The Governing Factor of Safety for Overturning and Sliding X Direction
Critical Load Case for Sliding along X-Direction: 208
Governing Disturbing Force: 39.577kN
Governing Restoring Force: 474.859kN
Minimum Sliding Ratio for the Critical Load Case: 11.998
Critical Load Case for Overturning w.r.t. X-Direction: 206
Governing Overturning Moment: -5.509kNm
Governing Resisting Moment: 1806.588kNm
Minimum Overturning Ratio for the Critical Load Case: 327.918
Critical Load Case and The Governing Factor of Safety for Overturning and Sliding Z Direction
Critical Load Case for Sliding along Z-Direction: 206
Governing Disturbing Force: -4.971Kn
Governing Restoring Force: 515.285kN
Minimum Sliding Ratio for the Critical Load Case: 103.654
Critical Load Case for Overturning w.r.t. Z-Direction: 208
Governing Overturning Moment: -22.539kNm
pg. 131
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Critical Load Case and The Governing Factor of Safety for Sliding Along Resultant Direction
Critical Load Case for Sliding along Resultant Direction: 208
Governing Disturbing Force: 39.767kN
Governing Restoring Force: 474.859kN
Minimum Sliding Ratio for the Critical Load Case: 11.941
------------------------------------------------------
Moment Calculation
= 0.800000
= 1.000000
Depth of Neutral Axis(X) = 0.129185m
Limit Moment of Resistance (M u max) = = 1991.371452kNm
Mu <= M u max hence, safe
Check Trial Depth against moment (w.r.t. Z Axis)
Critical Load Case = #211
pg. 132
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
= 0.800000
= 1.000000
Depth of Neutral Axis(X) = 0.129185m
Limit Moment of Resistance (M u max) = = 2901.712687kNm
Mu <= M u max hence, safe
------------------------------------------------------
One-
One-Way Shear Along Z (Shear Plane Parallel to Global Z Axis)
2.55m 1.75m 1.893m 1.893m PlanXZ
Critical Load Case = # 211
DZ = 1.893m
Shear Force(S) = 208.767kN
Percentage of Steel (Pt) = 0.0024
As Per EN-1992-1-1:2004 Clause No.6.2.2(1)
Resisting Shear (V rdc) = 740.7928kN
hence, safe
One-
One-Way Shear Along X
pg. 133
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
hence, safe
hence, safe
Reinforcement Calculation
Along X Axis
Bar diameter corresponding to max bar size (db) = 16mm
As Per EN-1992-1-1:2004 Clause No.8.4.3,8.4.4 and Table 8.2
pg. 134
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Along Z Axis
Bar diameter corresponding to max bar size(db) = 16mm
As Per EN-
EN-1992-
1992-1-1:2004 Clause No.8.4.3,8.4.4 and Table 8.2
Development Length (l d) = 0.162m
pg. 135
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
pg. 136
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
0.45m1.05m Elevation
2.55m 1.7m 3.4m 5.1m 0.46m 0.34m XZ Plan
Input Values
Footing Geometry
Column Dimensions
Column Shape: Rectangular
Column Length - X (Pl): 0.460m
Column Width - Z (Pw): 0.340m
Pedestal
Include Pedestal? No
Pedestal Shape: N/A
Pedestal Height (Ph): N/A
Pedestal Length - X (Pl): N/A
Pedestal Width - Z (Pw): N/A
pg. 137
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Design Parameters
Soil Properties
Soil Type: Cohesionless Soil Unit Weight: 17.000kN/m3
Soil Bearing Capacity: 61.700kN/m2
Soil Bearing Capacity Type: Gross Bearing Capacity Soil Surcharge: 0.000kN/m2
Depth of Soil above Footing: 1050.000mm
Type of Depth: Fixed Bottom Undrained Shear Strength: 0.000kN/m2
Min Percentage of Slab in Contact: 100.000
pg. 138
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Global Settings
Top Reinforcement Option: Calculate only when foundation is subjected to uplift forces
Concrete Design Option: Net Pressure (Gross Pressure - Self Weight Pressure)
------------------------------------------------------
Load Combinations
pg. 139
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Applied Loads
pg. 140
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Axial Shear X
LC Shear Z Moment X Moment Z
(kN) (kN) (kN) (kNm) (kNm)
201 351.087 -2.934 0.830 1.644 5.090
202 350.980 -1.545 0.793 1.588 3.738
203 351.217 -1.892 0.783 1.573 4.091
204 353.299 -3.123 0.713 1.466 5.325
205 351.392 -1.671 0.751 1.523 3.884
206 462.118 3.178 0.682 1.413 -0.960
207 463.306 1.442 0.630 1.341 0.802
208 473.716 -4.710 0.281 0.805 6.977
209 464.179 2.549 0.469 1.092 -0.229
210 406.869 -3.350 0.847 1.671 5.445
211 546.059 -0.919 0.799 1.595 2.952
212 546.653 -1.787 0.773 1.559 3.832
213 551.858 -4.863 0.598 1.291 6.920
214 547.089 -1.233 0.692 1.434 3.317
Design Calculations
Footing Size
Initial Length (Lo) = 5.100m
Initial Width (Wo) = 3.200m
Uplift force due to buoyancy = 0.000kN
Effect due to adhesion = 0.000kN
Area from initial length and width, A o = Lo X Wo = 16.320m2
Min. area required from bearing pressure, Amin = P / q max = 16.596m2
pg. 141
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Pressures at 4 Corners
Pressure at Pressure at Pressure at Pressure at Area of
Load Case top left top right bottom right bottom left footing in
corner corner corner corner uplift
(kN/m2) (kN/m2) (kN/m2) (kN/m2) (Au) (2)
213 61.2239 59.9880 60.3055 61.5414 0.000
pg. 142
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Stability Check
0.45 m1.05 frictional Force Sliding Force OTM
Factor of safety against
- Factor of safety against sliding overturning
Load
Along X- Along Z- Required W.R.T. X- W.R.T. Z- Required
Case Resultant
Direction Direction FOS Direction Direction FOS
No.
pg. 143
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Critical Load Case and The Governing Factor of Safety for Overturning and Sliding X Direction
Critical Load Case for Sliding along X-Direction: 208
Governing Disturbing Force: -4.710kN
Governing Restoring Force: 487.759kN
Minimum Sliding Ratio for the Critical Load Case: 103.550
Critical Load Case for Overturning w.r.t. X-Direction: 201
Governing Overturning Moment: 2.018kNm
Governing Resisting Moment: 1452.877kNm
Minimum Overturning Ratio for the Critical Load Case: 720.074
Critical Load Case and The Governing Factor of Safety for Overturning and Sliding Z Direction
Critical Load Case for Sliding along Z-Direction: 201
Governing Disturbing Force: 0.830kN Governing Restoring Force: 426.444kN
Minimum Sliding Ratio for the Critical Load Case: 513.865
Critical Load Case for Overturning w.r.t. Z-Direction: 208
Governing Overturning Moment: 9.096kNm Governing Resisting Moment: 2489.829kNm
Minimum Overturning Ratio for the Critical Load Case: 273.718
Critical Load Case and The Governing Factor of Safety for Sliding Along Resultant Direction
Critical Load Case for Sliding along Resultant Direction: 208
Governing Disturbing Force: 4.719kN Governing Restoring Force: 487.759kN
pg. 144
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Moment Calculation
= 0.800000
= 1.000000
Depth of Neutral Axis(X) = 0.129185m
Limit Moment of Resistance (M u max) = = 1934.475125kNm
Mu <= M u max hence, safe
= 0.800000
= 1.000000
Depth of Neutral Axis(X) = 0.129185m
Limit Moment of Resistance (M u max) = = 2901.712687kNm
pg. 145
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
One-
One-Way Shear Along Z (Shear Plane Parallel to Global Z Axis)
2.55m 1.7m 1.938m1.938m PlanXZ
hence, safe
One-
One-Way Shear Along X(Shear Plane Parallel to Global X Axis)
2.55m 1.7m 1.148m 1.148m PlanXZ
hence, safe
pg. 146
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
hence, safe
Reinforcement Calculation
Along X Axis
Bar diameter corresponding to max bar size (d b) = 16mm
As Per EN-1992-1-1:2004 Clause No.8.4.3,8.4.4 and Table 8.2
Development Length (l d) = 0.162m
Along Z Axis
Bar diameter corresponding to max bar size(db) = 16mm
As Per EN-1992-1-1:2004 Clause No.8.4.3,8.4.4 and Table 8.2
Development Length (l d) = 0.162m
pg. 147
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
pg. 148
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
pg. 149
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
ANNEXURE B
pg. 150
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
Where:
qadm: bearing capacity B: width of foundation D: depth of foundation
K d: coefficient equal to 1+0.33*D/B
pg. 151
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
We note that que bearing capacity obtained by the SPT method is lower than the one obtained with
the shear parameters by laboratory tests. The bearing capacity can thus be limited to the lowest
value obtained in
• The risks that can have on this site are the phenomena of collapse on the sandy parts, during
the execution of the excavation; consequently, it will be necessary to think of a system of
protection of the walls.
• In addition, we recommend that any tree or root stump, clayey, silty or looser pocket
detected at the opening of excavations be purged and replaced by large concrete or
compacted laterite.
• The foundations must be made in accordance with the standards and regulations in force
relating thereto including the DTU 13.12, Eurocodes, Fascicule 62.
• As part of the design and execution of the foundations, the company should ensure that the
water level is well below the anchoring depth of future foundations on a radius that covers
the right-of-way of the work at the time of the works.
• In addition, the bottom of excavation must not remain exposed or opened for long time to
the actions of bad weather so the realization of the concrete of foundation should be done as
soon as the completion of the excavation.
pg. 152
M/s TATA INTERNATIONAL ANVIL Projects
UNITECH, #17/24, Second Floor, North Mada Street,
Srinagar Colony, Saidapet, Chennai – 600 015.
PIKINE, SENEGAL. info@anvilprojects.in
Site: Senegal Doc. No.: Project No.: Date: 09/09/19
AA09 Rev.: 0
Title: RCC Foundation Design Report
ANNEXURE C
pg. 153
PAGE NO.
1
****************************************************
* *
* STAAD.Pro V8i SELECTseries4 *
* Version 20.07.09.31 *
* Proprietary Program of *
* Bentley Systems, Inc. *
* Date= SEP 5, 2019 *
* Time= 17:17:16 *
* *
* USER ID: MARMAG *
****************************************************
1. STAAD SPACE
INPUT FILE: MM-PKM-D19056 - V1.27- AISC - FINAL EURO_BS.STD
2. START JOB INFORMATION
3. ENGINEER DATE 19-JUL-19
4. JOB NAME PROPOSED STRUCTURE
5. JOB CLIENT PKM
6. JOB NO 56-MM-PKM-D19056
7. JOB REV 00
8. ENGINEER NAME PKH
9. CHECKER NAME RSK
10. APPROVED NAME SKV
11. END JOB INFORMATION
12. INPUT WIDTH 79
13. UNIT METER KN
14. JOINT COORDINATES
15. 2 0 3 0; 4 0 3 5; 5 7.54 -0.4 0; 6 5 3 0; 7 7.54 -0.4 5; 8 5 3 5
16. 13 14.72 -0.4 0; 14 14.72 3 0; 15 14.72 -0.4 5; 16 14.72 3 5; 18
17.26 3 0
17. 20 17.26 3 5; 21 22.26 -0.4 0; 22 22.26 3 0; 23 22.26 -0.4 5; 24
22.26 3 5
18. 25 27.26 -0.4 0; 26 27.26 3 0; 27 27.26 -0.4 5; 28 27.26 3 5; 29
31.76 -0.4 0
19. 30 31.76 3 0; 31 31.76 -0.4 5; 32 31.76 3 5; 40 5 3 10; 44 14.72
3 10
20. 46 17.26 3 10; 48 22.26 3 10; 50 27.26 3 10; 52 31.76 3 10; 58 5
3 -5
21. 62 14.72 3 -5; 64 17.26 3 -5; 66 22.26 3 -5; 68 27.26 3 -5; 79
23.51 3 -5
22. 80 24.76 3 -5; 81 26.01 3 -5; 83 19.76 3 -5; 84 21.01 3 -5; 85
28.385 3 -5
23. 86 29.51 3 -5; 87 30.635 3 -5; 89 15.99 3 -5; 94 1.25 3 10; 95
2.5 3 10
24. 96 3.75 3 10; 99 10.412 3 10; 100 11.848 3 10; 101 13.284 3 10;
102 15.99 3 10
25. 103 18.51 3 10; 104 19.76 3 10; 105 21.01 3 10; 106 23.51 3 10;
107 24.76 3 10
26. 108 26.01 3 10; 109 28.385 3 10; 110 29.51 3 10; 111 30.635 3 10
27. 112 33.01 3 10; 113 34.26 3 10; 114 35.51 3 10; 115 3.75 3 5; 116
2.5 3 5
28. 117 1.25 3 5; 118 3.75 3 0; 119 2.5 3 0; 120 1.25 3 0; 121 35.51
3 5
29. 122 34.26 3 5; 123 33.01 3 5; 124 30.635 3 5; 125 29.51 3 5; 126
28.385 3 5
30. 127 26.01 3 5; 128 24.76 3 5; 129 23.51 3 5; 130 21.01 3 5; 131
19.76 3 5
31. 132 18.51 3 5; 133 15.99 3 5; 134 13.284 3 5; 135 11.848 3 5; 136
10.412 3 5
32. 142 30.635 3 0; 143 29.51 3 0; 144 28.385 3 0; 145 26.01 3 0; 146
24.76 3 0
33. 147 23.51 3 0; 148 21.01 3 0; 149 19.76 3 0; 150 18.51 3 0; 151
15.99 3 0
34. 152 13.284 3 0; 153 11.848 3 0; 154 10.412 3 0; 161 31.76 3 -5;
162 0 6.8 0
35. 164 37 6.8 0; 166 18.5 8.65 0; 169 0 -0.4 0; 170 37 -0.4 0; 171 0
6.8 5
36. 173 37 6.8 5; 175 18.5 8.65 5; 176 0 -0.4 5; 177 37 -0.4 5; 178 0
3 -5
37. 179 0 6.8 -5; 181 37 6.8 -5; 183 18.5 8.65 -5; 184 0 -0.4 -5; 185
37 -0.4 -5
38. 186 0 3 10; 187 0 6.8 10; 189 37 6.8 10; 191 18.5 8.65 10; 192 0
-0.4 10
STAAD SPACE -- PAGE NO.
2
39. 193 37 -0.4 10; 194 0 3 15.1; 195 0 6.8 15.1; 197 37 6.8 15.1
40. 199 18.5 8.65 15.1; 200 0 -0.4 15.1; 201 37 -0.4 15.1; 202 0 3
18.6
41. 203 0 6.8 18.6; 205 37 6.8 18.6; 207 18.5 8.65 18.6; 208 0 -0.4
18.6
42. 209 37 -0.4 18.6; 210 0 3 25; 211 0 6.8 25; 213 37 6.8 25; 215
18.5 8.65 25
43. 216 0 -0.4 25; 218 0 3 30; 219 0 6.8 30; 221 37 6.8 30; 223 18.5
8.65 30
44. 224 0 -0.4 30; 225 37 -0.4 30; 226 0 3 34.74; 227 0 6.8 34.74
45. 229 37 6.8 34.74; 231 18.5 8.65 34.74; 232 0 -0.4 34.74; 233 37 -
0.4 34.74
46. 234 0 3 39.725; 235 0 6.8 39.725; 237 37 6.8 39.725; 239 18.5
8.65 39.725
47. 240 0 -0.4 39.725; 241 37 -0.4 39.725; 242 37 3 5; 243 5 -0.4 10
48. 245 14.72 -0.4 10; 247 22.26 -0.4 10; 248 27.26 -0.4 10; 249
31.76 -0.4 10
49. 250 37 3 10; 251 5 -0.4 -5; 252 9.74 -0.4 -5; 254 18.5 -0.4 -5
50. 255 22.26 -0.4 -5; 256 27.26 -0.4 -5; 257 31.76 -0.4 -5; 265 37 3
-5
51. 270 37 3 39.725; 271 37 3 0; 279 5 7.3 -5; 280 31.76 7.324 -5
52. 281 22.26 8.274 -5; 282 27.26 7.774 -5; 286 37 3 15.1; 287 37 3
18.6
53. 289 37 3 30; 290 37 3 34.74; 291 37 4.7 25; 292 37 4.7 18.6; 293
37 4.7 30
54. 297 18.5 3 -5; 299 0 6.8 45; 301 37 6.8 45; 303 18.5 8.65 45; 304
0 3 45
55. 305 0 -0.4 45; 306 37 -0.4 45; 307 37 3 45; 308 5 3 15.1; 309
1.25 3 15.1
56. 310 2.5 3 15.1; 311 3.75 3 15.1; 312 5 -0.4 15.1; 313 5 3 25; 314
5 3 30
57. 315 1.25 3 25; 316 1.25 3 30; 317 2.5 3 25; 318 2.5 3 30; 319
3.75 3 25
58. 320 3.75 3 30; 321 5 -0.4 30; 322 5 3 34.74; 323 1.25 3 34.74;
324 2.5 3 34.74
59. 325 3.75 3 34.74; 326 5 -0.4 34.74; 327 5 3 39.725; 328 1.25 3
39.725
60. 329 2.5 3 39.725; 330 3.75 3 39.725; 331 5 -0.4 39.725; 332 5 3
45
61. 333 1.25 3 45; 334 2.5 3 45; 335 3.75 3 45; 336 5 -0.4 45; 337 5
3 18.6
62. 339 1.25 3 18.6; 341 2.5 3 18.6; 343 3.75 3 18.6; 346 5 -0.4 25
63. 353 5 -0.4 18.6; 354 6.25 3 10; 355 6.25 3 15.1; 356 6.25 3 25;
357 6.25 3 30
64. 358 6.25 3 34.74; 359 6.25 3 39.725; 360 6.25 3 45; 361 6.25 3
18.6
65. 362 31.76 3 15.1; 363 33.01 3 15.1; 364 34.26 3 15.1; 365 35.51 3
15.1
66. 366 31.76 -0.4 15.1; 376 31.76 -0.4 17.75; 377 22.26 8.274 0
67. 378 22.26 8.274 34.74; 379 22.26 8.274 39.725; 380 22.26 8.274 30
68. 381 22.26 8.274 25; 382 22.26 8.274 18.6; 383 22.26 8.274 15.1
69. 384 22.26 8.274 10; 385 22.26 8.274 5; 386 22.26 8.274 45; 387
27.26 7.774 0
70. 388 27.26 7.774 34.74; 389 27.26 7.774 39.725; 390 27.26 7.774 30
71. 391 27.26 7.774 25; 392 27.26 7.774 18.6; 393 27.26 7.774 15.1
72. 394 27.26 7.774 10; 395 27.26 7.774 5; 396 27.26 7.774 45; 397
31.76 7.324 0
73. 398 31.76 7.324 34.74; 399 31.76 7.324 39.725; 400 31.76 7.324 30
74. 401 31.76 7.324 25; 402 31.76 7.324 18.6; 403 31.76 7.324 15.1
75. 404 31.76 7.324 10; 405 31.76 7.324 5; 406 31.76 7.324 45; 427 5
7.3 0
76. 428 5 7.3 34.74; 429 5 7.3 39.725; 430 5 7.3 30; 431 5 7.3 25;
432 5 7.3 18.6
77. 433 5 7.3 15.1; 434 5 7.3 10; 435 5 7.3 5; 436 5 7.3 45; 437 37 3
17.75
78. 438 31.76 3 17.75; 439 33.01 3 17.75; 440 34.26 3 17.75; 441
35.51 3 17.75
79. 442 0 6.8 50; 443 5 7.3 50; 444 37 6.8 50; 445 31.76 7.324 50
80. 447 27.26 7.774 50; 450 0 3 50; 451 0 -0.4 50; 452 37 -0.4 50;
453 37 3 50
81. 454 18.5 8.65 50; 455 22.26 8.274 50; 457 0 6.8 55; 458 5 7.3 55
82. 459 37 6.8 55; 460 31.76 7.324 55; 462 27.26 7.774 55; 465 0 3 55
83. 466 0 -0.4 55; 467 37 -0.4 55; 468 37 3 55; 469 18.5 8.65 55
84. 470 22.26 8.274 55; 472 0 6.8 60; 473 5 7.3 60; 474 37 6.8 60
85. 475 31.76 7.324 60; 477 27.26 7.774 60; 480 0 3 60; 481 0 -0.4 60
86. 482 37 -0.4 60; 483 37 3 60; 484 18.5 8.65 60; 485 22.26 8.274 60
87. 487 0 6.8 65; 488 5 7.3 65; 489 37 6.8 65; 490 31.76 7.324 65
88. 492 27.26 7.774 65; 495 0 3 65; 496 0 -0.4 65; 497 37 -0.4 65;
498 37 3 65
89. 499 18.5 8.65 65; 500 22.26 8.274 65; 502 0 6.8 70; 503 5 7.3 70
90. 504 37 6.8 70; 505 31.76 7.324 70; 507 27.26 7.774 70; 510 0 3 70
91. 511 0 -0.4 70; 512 37 -0.4 70; 513 37 3 70; 514 18.5 8.65 70
92. 515 22.26 8.274 70; 517 0 6.8 75; 518 5 7.3 75; 519 37 6.8 75
93. 520 31.76 7.324 75; 522 27.26 7.774 75; 525 0 3 75; 526 0 -0.4 75
94. 527 37 -0.4 75; 528 37 3 75; 529 18.5 8.65 75; 530 22.26 8.274 75
STAAD SPACE -- PAGE NO.
3
95. 532 0 6.8 80; 533 5 7.3 80; 534 37 6.8 80; 535 31.76 7.324 80
96. 537 27.26 7.774 80; 540 0 3 80; 541 0 -0.4 80; 542 37 -0.4 80;
543 37 3 80
97. 544 18.5 8.65 80; 545 22.26 8.274 80; 547 0 6.8 85; 548 5 7.3 85
98. 549 37 6.8 85; 550 31.76 7.324 85; 552 27.26 7.774 85; 555 0 3 85
99. 556 0 -0.4 85; 557 37 -0.4 85; 558 37 3 85; 559 18.5 8.65 85
100. 560 22.26 8.274 85; 562 0 6.8 90; 563 5 7.3 90; 564 37 6.8 90
101. 565 31.76 7.324 90; 567 27.26 7.774 90; 570 0 3 90; 571 0 -0.4 90
102. 574 18.5 8.65 90; 575 22.26 8.274 90; 577 0 6.8 93.145; 578 5 7.3
93.145
103. 579 37 6.8 93.145; 580 31.76 7.324 93.145; 582 27.26 7.774 93.145
104. 585 0 3 93.145; 586 0 -0.4 93.145; 587 37 -0.4 93.145; 588 37 3
93.145
105. 589 18.5 8.65 93.145; 590 22.26 8.274 93.145; 592 37 4.7 90; 593
37 4.7 85
106. 594 37 4.7 93.145; 595 0 6.8 98.145; 596 37 6.8 98.145; 597 18.5
8.65 98.145
107. 598 22.26 8.274 98.145; 599 27.26 7.774 98.145; 600 31.76 7.324
98.145
108. 603 5 7.3 98.145; 604 0 3 98.145; 605 0 -0.4 98.145; 606 37 -0.4
98.145
109. 607 37 3 98.145; 608 5 -0.4 98.145; 609 5 3 98.145; 610 9.74 -0.4
98.145
110. 612 13.855 -0.4 98.145; 616 22.26 -0.4 98.145; 617 22.26 3 98.145
111. 618 27.26 -0.4 98.145; 619 27.26 3 98.145; 620 31.76 -0.4 98.145
112. 621 31.76 3 98.145; 622 1.25 3 98.145; 629 3.75 3 98.145; 630 2.5
3 98.145
113. 637 5 -0.4 93.145; 638 5 3 93.145; 639 1.25 3 93.145; 640 3.75 3
93.145
114. 641 2.5 3 93.145; 644 6.25 3 93.145; 645 8.75 3 93.145; 646 7.5 3
93.145
115. 648 6.25 3 98.145; 649 7.5 3 98.145; 650 8.75 3 98.145; 651 12.2
-0.4 93.145
116. 652 12.2 3 93.145; 653 12.2 3 98.145; 656 10.85 3 93.145; 657
10.85 3 98.145
117. 752 9.74 3 98.145; 753 9.74 7.774 98.145; 755 13.855 3 98.145
118. 756 13.855 8.1855 98.145; 757 13.855 8.1855 -5; 758 13.855 8.1855
0
119. 759 13.855 8.1855 34.74; 760 13.855 8.1855 39.725; 761 13.855
8.1855 30
120. 762 13.855 8.1855 25; 763 13.855 8.1855 18.6; 764 13.855 8.1855
15.1
121. 765 13.855 8.1855 10; 766 13.855 8.1855 5; 767 13.855 8.1855 45
122. 768 13.855 8.1855 50; 769 13.855 8.1855 55; 770 13.855 8.1855 60
123. 771 13.855 8.1855 65; 772 13.855 8.1855 70; 773 13.855 8.1855 75
124. 774 13.855 8.1855 80; 775 13.855 8.1855 85; 776 13.855 8.1855 90
125. 777 13.855 8.1855 93.145; 778 9.74 7.774 -5; 779 9.74 7.774 0
126. 780 9.74 7.774 34.74; 781 9.74 7.774 39.725; 782 9.74 7.774 30
127. 783 9.74 7.774 25; 784 9.74 7.774 18.6; 785 9.74 7.774 15.1; 786
9.74 7.774 10
128. 787 9.74 7.774 5; 788 9.74 7.774 45; 789 9.74 7.774 50; 790 9.74
7.774 55
129. 791 9.74 7.774 60; 792 9.74 7.774 65; 793 9.74 7.774 70; 794 9.74
7.774 75
130. 795 9.74 7.774 80; 796 9.74 7.774 85; 797 9.74 7.774 90; 798 9.74
7.774 93.145
131. 799 13.855 3.0005 -5; 800 13.855 -0.3995 -5; 801 9.74 3 -5
132. 802 9.74 -0.4 93.145; 803 9.74 3 93.145; 804 7.54 3 0; 805 7.54 3
5
133. 807 9.74 3 0; 812 9.74 -0.4 10; 813 9.74 3 10; 814 6.25 3 5; 815
6.25 3 0
134. 816 7.63733 3 0; 817 9.02467 3 0; 818 7.63733 3 5; 819 7.63733 3
10
135. 820 9.02467 3 5; 821 9.02467 3 10; 822 17.26 -0.4 0; 823 17.26 -
0.4 5
136. 824 17.26 -0.4 10; 825 28.502 3 15.1; 826 28.502 -0.4 15.1; 827
24.502 3 15.1
137. 828 24.502 -0.4 15.1; 829 20.502 3 15.1; 830 20.502 -0.4 15.1
138. 831 16.502 3 15.1; 832 16.502 -0.4 15.1; 833 14.72 3 15.1; 834
17.26 3 15.1
139. 835 22.26 3 15.1; 836 27.26 3 15.1; 837 10.412 3 15.1; 838 11.848
3 15.1
140. 839 13.284 3 15.1; 840 15.99 3 15.1; 841 18.51 3 15.1; 842 19.76
3 15.1
141. 843 21.01 3 15.1; 844 23.51 3 15.1; 845 24.76 3 15.1; 846 26.01 3
15.1
142. 847 28.385 3 15.1; 848 29.51 3 15.1; 849 30.635 3 15.1; 850
7.63733 3 15.1
143. 851 9.74 3 15.1; 852 9.02467 3 15.1; 853 9.74 -0.4 15.1; 854 6.25
3 -5
144. 855 7.63733 3 -5; 856 9.02467 3 -5; 857 7.54 -2.1 0; 858 7.54 -
2.1 5
145. 859 14.72 -2.1 0; 860 14.72 -2.1 5; 861 22.26 -2.1 0; 862 22.26 -
2.1 5
146. 863 27.26 -2.1 0; 864 27.26 -2.1 5; 865 31.76 -2.1 0; 866 31.76 -
2.1 5
147. 867 0 -2.1 0; 868 37 -2.1 0; 869 0 -2.1 5; 870 37 -2.1 5; 871 0 -
2.1 -5
148. 872 37 -2.1 -5; 873 0 -2.1 10; 874 37 -2.1 10; 875 0 -2.1 15.1
149. 876 37 -2.1 15.1; 877 0 -2.1 18.6; 878 37 -2.1 18.6; 879 0 -2.1
25
150. 880 0 -2.1 30; 881 37 -2.1 30; 882 0 -2.1 34.74; 883 37 -2.1
34.74
STAAD SPACE -- PAGE NO.
4
151. 884 0 -2.1 39.725; 885 37 -2.1 39.725; 886 5 -2.1 10; 887 14.72 -
2.1 10
152. 888 22.26 -2.1 10; 889 27.26 -2.1 10; 890 31.76 -2.1 10; 891 5 -
2.1 -5
153. 892 9.74 -2.1 -5; 893 18.5 -2.1 -5; 894 22.26 -2.1 -5; 895 27.26
-2.1 -5
154. 896 31.76 -2.1 -5; 897 0 -2.1 45; 898 37 -2.1 45; 899 5 -2.1 15.1
155. 900 5 -2.1 30; 901 5 -2.1 34.74; 902 5 -2.1 39.725; 903 5 -2.1 45
156. 904 5 -2.1 25; 905 5 -2.1 18.6; 906 31.76 -2.1 15.1; 907 31.76 -
2.1 17.75
157. 908 0 -2.1 50; 909 37 -2.1 50; 910 0 -2.1 55; 911 37 -2.1 55; 912
0 -2.1 60
158. 913 37 -2.1 60; 914 0 -2.1 65; 915 37 -2.1 65; 916 0 -2.1 70; 917
37 -2.1 70
159. 918 0 -2.1 75; 919 37 -2.1 75; 920 0 -2.1 80; 921 37 -2.1 80; 922
0 -2.1 85
160. 923 37 -2.1 85; 924 0 -2.1 90; 925 0 -2.1 93.145; 926 37 -2.1
93.145
161. 927 0 -2.1 98.145; 928 37 -2.1 98.145; 929 5 -2.1 98.145; 930
9.74 -2.1 98.145
162. 931 13.855 -2.1 98.145; 932 22.26 -2.1 98.145; 933 27.26 -2.1
98.145
163. 934 31.76 -2.1 98.145; 935 5 -2.1 93.145; 936 12.2 -2.1 93.145
164. 937 13.855 -2.0995 -5; 938 9.74 -2.1 93.145; 939 9.74 -2.1 10
165. 940 17.26 -2.1 0; 941 17.26 -2.1 5; 942 17.26 -2.1 10; 943 28.502
-2.1 15.1
166. 944 24.502 -2.1 15.1; 945 20.502 -2.1 15.1; 946 16.502 -2.1 15.1
167. 947 9.74 -2.1 15.1; 948 12.2 -0.4 98.145; 949 0 -0.4 27.5; 950 5
-0.4 27.5
168. 951 14.72 -0.399593 -5; 952 17.26 -0.399867 -5; 953 31.76 -0.4
9.5
169. 954 31.76 -0.4 11.4; 955 37 -0.4 9.5; 956 37 -0.4 11.4; 957 37 -
0.4 17.75
170. 958 18.5 -0.4 0; 959 14.72 -0.4 7; 960 17.26 -0.4 7; 961 35.15 -
0.4 5
171. 962 35.15 -0.4 9.5; 963 0 -0.4 17.5; 964 5 -0.4 17.5; 965 3.7 -
0.4 10
172. 966 3.7 -0.4 15.1; 967 2 -0.4 10; 968 2 -0.4 15.1; 969 0 -0.4
11.2
173. 970 2 -0.4 11.2; 971 0 -0.4 12.2; 972 2 -0.4 12.2; 973 0 -0.4
14.1
174. 974 3.7 -0.4 14.1; 975 1 -0.4 17.5; 976 2.7 -0.4 17.5; 977 1 -0.4
15.1
175. 978 2.7 -0.4 15.1; 979 18.1 -0.399957 -5; 980 18.1 -0.4 0; 981 2
-0.4 14.1
176. ***
177. MEMBER INCIDENCES
178. 3 5 804; 4 7 805; 7 13 14; 8 15 16; 11 21 22; 12 23 24; 13 25 26;
14 27 28
179. 15 29 30; 16 31 32; 19 4 117; 21 32 123; 22 28 126; 23 24 129; 24
20 132
180. 25 16 133; 27 8 814; 29 26 144; 30 22 147; 31 18 150; 32 14 151;
34 6 815
181. 72 62 14; 73 64 18; 74 66 22; 75 68 26; 82 8 40; 83 6 8; 84 16
44; 85 14 16
182. 86 20 46; 87 18 20; 88 24 48; 89 22 24; 90 28 50; 91 26 28; 92 32
52
183. 134 89 151; 136 297 150; 138 83 149; 140 84 148; 142 79 147; 144
80 146
184. 146 81 145; 148 85 144; 150 86 143; 152 87 142; 159 115 8; 160
116 115
185. 161 117 116; 162 118 6; 163 119 118; 164 120 119; 165 121 242;
166 122 121
186. 167 123 122; 168 124 32; 169 125 124; 170 126 125; 171 127 28;
172 128 127
187. 173 129 128; 174 130 24; 175 131 130; 176 132 131; 177 133 20;
178 134 16
188. 179 135 134; 180 136 135; 186 142 30; 187 143 142; 188 144 143;
189 145 26
189. 190 146 145; 191 147 146; 192 148 22; 193 149 148; 194 150 149;
195 151 18
190. 201 117 94; 202 120 117; 203 116 95; 204 119 116; 205 115 96; 206
118 115
191. 211 136 99; 212 154 136; 213 135 100; 214 153 135; 215 134 101;
216 152 134
192. 217 133 102; 218 151 133; 219 132 103; 220 150 132; 221 131 104;
222 149 131
193. 223 130 105; 224 148 130; 225 129 106; 226 147 129; 227 128 107;
228 146 128
194. 229 127 108; 230 145 127; 231 126 109; 232 144 126; 233 125 110;
234 143 125
195. 235 124 111; 236 142 124; 237 123 112; 239 122 113; 241 121 114;
244 58 6
196. 250 161 30; 252 30 32; 259 2 120; 261 2 162; 262 169 2; 263 170
271; 268 4 171
197. 269 176 4; 270 177 242; 271 179 279; 272 181 280; 273 280 282;
275 178 179
198. 276 184 178; 277 185 265; 282 186 187; 283 192 186; 284 193 250;
289 194 195
199. 290 200 194; 291 201 286; 296 202 203; 297 208 202; 298 209 287;
299 211 431
200. 300 213 401; 303 210 211; 304 216 210; 310 218 219; 311 224 218;
312 225 289
201. 317 226 227; 318 232 226; 319 233 290; 324 234 235; 325 240 234;
326 241 270
202. 327 4 186; 328 2 4; 330 242 173; 331 243 40; 333 245 44; 335 247
48
203. 336 248 50; 337 249 52; 338 186 94; 339 52 112; 340 50 109; 341
48 106
204. 342 46 103; 343 44 102; 345 40 354; 346 96 40; 347 95 96; 348 94
95
205. 349 250 189; 350 114 250; 351 113 114; 352 112 113; 353 111 52;
354 110 111
206. 355 109 110; 356 108 50; 357 107 108; 358 106 107; 359 105 48;
360 104 105
STAAD SPACE -- PAGE NO.
5
207. 361 103 104; 362 102 46; 363 101 44; 364 100 101; 365 99 100; 367
354 819
208. 368 251 58; 369 252 801; 371 254 297; 372 255 66; 373 256 68; 374
257 161
209. 375 178 58; 376 161 265; 377 68 85; 378 66 79; 379 64 297; 380 62
89
210. 381 58 854; 386 265 181; 390 87 161; 391 86 87; 392 85 86; 393 81
68
211. 394 80 81; 395 79 80; 396 84 66; 397 83 84; 398 297 83; 399 89
64; 405 179 162
212. 406 181 164; 407 178 2; 409 270 237; 411 242 250; 412 271 164;
413 265 271
213. 414 271 242; 415 58 279; 416 801 778; 418 297 183; 419 66 281;
420 68 282
214. 421 161 280; 424 281 183; 425 282 281; 427 757 183; 428 279 778;
429 286 197
215. 430 287 292; 432 289 293; 433 290 229; 434 227 235; 435 219 227;
436 211 219
216. 437 203 211; 438 195 203; 439 187 195; 440 171 187; 441 162 171;
442 229 237
217. 443 221 229; 444 213 221; 445 205 213; 446 197 205; 447 189 197;
448 173 189
218. 449 164 173; 455 290 270; 456 289 290; 460 291 213; 461 292 205;
462 291 292
219. 463 293 221; 464 291 293; 473 304 299; 474 305 304; 475 306 307;
476 307 301
220. 477 235 299; 478 237 301; 480 270 307; 481 40 308; 482 94 309;
483 95 310
221. 484 96 311; 485 186 194; 486 312 308; 487 194 309; 488 311 308;
489 310 311
222. 490 309 310; 491 313 314; 492 315 316; 493 317 318; 494 319 320;
495 210 218
223. 496 321 314; 497 218 316; 498 320 314; 499 318 320; 500 316 318;
501 314 322
224. 502 316 323; 503 318 324; 504 320 325; 505 218 226; 506 326 322;
507 226 323
225. 508 325 322; 509 324 325; 510 323 324; 511 322 327; 512 323 328;
513 324 329
226. 514 325 330; 515 226 234; 516 331 327; 517 234 328; 518 330 327;
519 329 330
227. 520 328 329; 521 327 332; 522 328 333; 523 329 334; 524 330 335;
525 234 304
228. 526 336 332; 527 304 333; 528 335 332; 529 334 335; 530 333 334;
536 346 313
229. 537 210 315; 538 319 313; 539 317 319; 540 315 317; 541 337 313;
542 308 337
230. 543 339 315; 544 309 339; 545 341 317; 546 310 341; 547 343 319;
548 311 343
231. 549 202 210; 550 194 202; 556 353 337; 557 202 339; 558 343 337;
559 341 343
232. 560 339 341; 562 354 355; 563 308 355; 564 356 357; 565 314 357;
566 357 358
233. 567 322 358; 568 358 359; 569 327 359; 570 359 360; 571 332 360;
572 313 356
234. 573 361 356; 574 355 361; 575 337 361; 576 52 362; 577 112 363;
578 113 364
235. 579 114 365; 580 366 362; 581 362 363; 582 365 286; 583 364 365;
584 363 364
236. 585 250 286; 591 362 438; 592 363 439; 593 364 440; 594 365 441;
595 376 438
237. 596 438 439; 597 441 437; 598 440 441; 599 439 440; 600 286 437;
601 183 166
238. 602 231 239; 603 223 231; 604 215 223; 605 207 215; 606 199 207;
607 191 199
239. 608 175 191; 609 166 175; 610 239 303; 612 281 377; 615 378 379;
617 380 378
240. 618 381 215; 619 381 380; 621 382 381; 623 383 382; 625 384 383;
627 385 384
241. 628 377 385; 630 379 386; 632 282 387; 635 388 389; 637 390 388;
638 391 381
242. 639 391 390; 641 392 391; 643 393 392; 645 394 393; 647 395 394;
648 387 395
243. 650 389 396; 652 280 397; 655 398 399; 657 400 398; 659 401 400;
661 402 401
244. 663 403 402; 665 404 403; 667 405 404; 668 397 405; 670 399 406;
678 762 215
245. 712 279 427; 715 428 429; 717 430 428; 719 431 430; 721 432 431;
723 433 432
246. 725 434 433; 727 435 434; 728 427 435; 730 429 436; 731 437 287;
732 184 2
247. 733 169 178; 734 178 162; 735 2 179; 736 179 427; 737 162 279;
744 183 377
248. 745 166 281; 746 281 387; 747 377 282; 748 282 397; 749 387 280;
750 280 164
249. 751 397 181; 752 181 271; 753 265 164; 754 271 185; 755 265 170;
780 224 226
250. 781 232 218; 782 218 227; 783 226 219; 784 219 428; 785 227 430;
792 223 378
251. 793 231 380; 794 380 388; 795 378 390; 796 390 398; 797 388 400;
798 400 229
252. 799 398 221; 800 221 290; 801 289 229; 802 290 225; 803 289 233;
808 450 442
253. 809 451 450; 810 452 453; 811 453 444; 812 299 442; 813 301 444;
814 307 453
254. 815 303 454; 817 386 455; 819 396 447; 821 406 445; 827 436 443;
832 465 457
255. 833 466 465; 835 468 459; 836 442 457; 837 444 459; 838 453 468;
839 454 469
256. 841 455 470; 843 447 462; 845 445 460; 851 443 458; 852 472 473;
853 474 475
257. 856 480 472; 857 481 480; 858 482 483; 859 483 474; 860 457 472;
861 459 474
258. 862 468 483; 863 469 484; 864 485 484; 865 470 485; 866 477 485;
867 462 477
259. 869 460 475; 870 770 484; 875 458 473; 880 495 487; 881 496 495;
882 497 498
260. 883 498 489; 884 472 487; 885 474 489; 886 483 498; 887 484 499;
889 485 500
261. 891 477 492; 893 475 490; 899 473 488; 904 510 502; 905 511 510;
906 512 513
262. 907 513 504; 908 487 502; 909 489 504; 910 498 513; 911 499 514;
913 500 515
STAAD SPACE -- PAGE NO.
6
263. 915 492 507; 917 490 505; 923 488 503; 928 525 517; 929 526 525;
930 527 528
264. 931 528 519; 932 502 517; 933 504 519; 934 513 528; 935 514 529;
937 515 530
265. 939 507 522; 941 505 520; 947 503 518; 952 540 532; 953 541 540;
954 542 543
266. 955 543 534; 956 517 532; 957 519 534; 958 528 543; 959 529 544;
961 530 545
267. 963 522 537; 965 520 535; 971 518 533; 976 555 547; 977 556 555;
978 557 558
268. 979 558 593; 980 532 547; 981 534 549; 982 543 558; 983 544 559;
985 545 560
269. 987 537 552; 989 535 550; 995 533 548; 1000 570 562; 1001 571 570
270. 1004 547 562; 1005 549 564; 1007 559 574; 1009 560 575; 1011 552
567
271. 1013 550 565; 1019 548 563; 1024 585 577; 1025 586 585; 1026 587
588
272. 1027 588 594; 1028 562 577; 1029 564 579; 1031 574 589; 1033 575
590
273. 1035 567 582; 1037 565 580; 1043 563 578; 1044 592 564; 1045 592
593
274. 1046 592 594; 1047 593 549; 1048 594 579; 1049 451 465; 1050 466
450
275. 1051 450 457; 1052 465 442; 1053 442 458; 1054 457 443; 1061 454
470
276. 1062 469 455; 1063 455 462; 1064 470 447; 1065 447 460; 1066 462
445
277. 1067 445 459; 1068 460 444; 1069 444 468; 1070 453 459; 1071 468
452
278. 1072 453 467; 1073 511 525; 1074 526 510; 1075 510 517; 1076 525
502
279. 1077 502 518; 1078 517 503; 1085 514 530; 1086 529 515; 1087 515
522
280. 1088 530 507; 1089 507 520; 1090 522 505; 1091 505 519; 1092 520
504
281. 1093 504 528; 1094 513 519; 1095 528 512; 1096 513 527; 1097 577
595
282. 1098 579 596; 1099 589 597; 1100 590 598; 1101 582 599; 1102 580
600
283. 1105 578 603; 1106 595 603; 1107 596 600; 1108 600 599; 1109 604
595
284. 1110 605 604; 1111 606 607; 1112 608 609; 1113 610 752; 1114 612
755
285. 1116 616 617; 1117 618 619; 1118 620 621; 1119 604 622; 1126 609
648
286. 1127 629 609; 1128 630 629; 1129 622 630; 1130 607 596; 1143 609
603
287. 1144 752 753; 1148 619 599; 1149 621 600; 1150 598 597; 1151 599
598
288. 1152 756 597; 1153 603 753; 1155 637 638; 1156 585 639; 1157 640
638
289. 1158 641 640; 1159 639 641; 1160 638 609; 1161 639 622; 1162 641
630
290. 1163 640 629; 1164 585 604; 1166 638 644; 1167 645 803; 1168 646
645
291. 1169 644 646; 1173 644 648; 1175 646 649; 1176 650 752; 1177 645
650
292. 1181 651 652; 1182 653 755; 1183 652 653; 1188 656 652; 1189 657
653
293. 1190 656 657; 1191 755 756; 1192 617 598; 1196 304 450; 1197 450
465
294. 1198 465 480; 1199 480 495; 1200 495 510; 1201 510 525; 1202 525
540
295. 1203 540 555; 1205 588 607; 1206 555 570; 1207 570 585; 1243 814
805
296. 1244 815 804; 1272 52 286; 1273 362 250; 1274 362 437; 1275 438
286
297. 1276 304 327; 1277 234 332; 1278 234 322; 1279 226 327; 1280 226
314
298. 1281 218 322; 1282 218 313; 1283 210 314; 1284 210 337; 1285 202
313
299. 1286 202 308; 1287 194 337; 1288 194 40; 1289 186 308; 1290 585
609
300. 1291 604 638; 1296 473 791; 1298 487 488; 1299 489 490; 1302 500
499
301. 1303 492 500; 1305 771 499; 1308 488 792; 1310 577 578; 1311 579
580
302. 1314 590 589; 1315 582 590; 1317 777 589; 1320 578 798; 1322 562
563
303. 1323 564 565; 1326 575 574; 1327 567 575; 1329 776 574; 1332 563
797
304. 1334 547 548; 1335 549 550; 1338 560 559; 1339 552 560; 1341 775
559
305. 1344 548 796; 1346 532 533; 1347 534 535; 1350 545 544; 1351 537
545
306. 1353 774 544; 1356 533 795; 1358 517 518; 1359 519 520; 1362 530
529
307. 1363 522 530; 1365 773 529; 1368 518 794; 1370 502 503; 1371 504
505
308. 1374 515 514; 1375 507 515; 1377 772 514; 1380 503 793; 1382 457
458
309. 1383 459 460; 1386 470 469; 1387 462 470; 1389 769 469; 1392 458
790
310. 1394 442 443; 1395 444 445; 1398 455 454; 1399 447 455; 1401 768
454
311. 1404 443 789; 1406 299 436; 1407 301 406; 1410 386 303; 1411 396
386
312. 1413 767 303; 1416 436 788; 1418 235 429; 1419 237 399; 1422 379
239
313. 1423 389 379; 1425 760 239; 1428 429 781; 1430 227 428; 1431 229
398
314. 1434 378 231; 1435 388 378; 1437 759 231; 1440 428 780; 1441 398
388
315. 1442 219 430; 1443 221 400; 1446 380 223; 1447 390 380; 1449 761
223
316. 1452 430 782; 1453 400 390; 1454 203 432; 1455 205 402; 1458 382
207
317. 1459 392 382; 1461 763 207; 1464 432 784; 1465 402 392; 1466 195
433
318. 1467 197 403; 1470 383 199; 1471 393 383; 1473 764 199; 1476 433
785
STAAD SPACE -- PAGE NO.
7
319. 1478 187 434; 1479 189 404; 1482 384 191; 1483 394 384; 1485 765
191
320. 1488 434 786; 1490 171 435; 1491 173 405; 1494 385 175; 1495 395
385
321. 1497 766 175; 1500 435 787; 1502 162 427; 1503 164 397; 1506 377
166
322. 1507 387 377; 1509 758 166; 1512 427 779; 1513 397 387; 1514 467
468
323. 1515 431 783; 1516 401 391; 1517 586 604; 1518 605 585; 1519 585
595
324. 1520 604 577; 1521 577 603; 1522 595 578; 1529 589 598; 1530 597
590
325. 1531 590 599; 1532 598 582; 1533 582 600; 1534 599 580; 1535 580
596
326. 1536 600 579; 1537 579 607; 1538 588 596; 1539 607 587; 1540 588
606
327. 1541 752 657; 1545 753 756; 1551 757 758; 1554 759 760; 1556 761
759
328. 1558 762 761; 1560 763 762; 1562 764 763; 1564 765 764; 1566 766
765
329. 1567 758 766; 1569 760 767; 1571 767 768; 1573 768 769; 1575 769
770
330. 1577 770 771; 1579 771 772; 1581 772 773; 1583 773 774; 1585 774
775
331. 1587 775 776; 1589 776 777; 1590 777 756; 1591 778 757; 1592 779
758
332. 1593 778 779; 1594 780 759; 1595 781 760; 1596 780 781; 1597 782
761
333. 1598 782 780; 1599 783 762; 1600 783 782; 1601 784 763; 1602 784
783
334. 1603 785 764; 1604 785 784; 1605 786 765; 1606 786 785; 1607 787
766
335. 1608 787 786; 1609 779 787; 1610 788 767; 1611 781 788; 1612 789
768
336. 1613 788 789; 1614 790 769; 1615 789 790; 1616 791 770; 1617 790
791
337. 1618 792 771; 1619 791 792; 1620 793 772; 1621 792 793; 1622 794
773
338. 1623 793 794; 1624 795 774; 1625 794 795; 1626 796 775; 1627 795
796
339. 1628 797 776; 1629 796 797; 1630 798 777; 1631 797 798; 1632 798
753
340. 1633 799 757; 1634 800 799; 1635 801 799; 1636 279 779; 1637 427
778
341. 1638 778 758; 1639 779 757; 1640 757 166; 1641 758 183; 1648 430
780
342. 1649 428 782; 1650 782 759; 1651 780 761; 1652 761 231; 1653 759
223
343. 1654 443 790; 1655 458 789; 1656 789 769; 1657 790 768; 1658 768
469
344. 1659 769 454; 1660 503 794; 1661 518 793; 1662 793 773; 1663 794
772
345. 1664 772 529; 1665 773 514; 1666 578 753; 1667 603 798; 1668 798
756
346. 1669 753 777; 1670 777 597; 1671 756 589; 1672 803 656; 1673 802
803
347. 1674 803 752; 1675 649 650; 1676 648 649; 1684 801 807; 1686 813
99
348. 1687 812 813; 1691 814 354; 1693 815 814; 1696 818 820; 1697 819
821
349. 1698 818 819; 1699 816 818; 1700 820 136; 1701 821 813; 1702 820
821
350. 1703 817 820; 1704 822 18; 1705 823 20; 1706 824 46; 1707 826 825
351. 1708 828 827; 1709 830 829; 1710 832 831; 1711 44 833; 1712 46
834
352. 1713 48 835; 1714 50 836; 1715 99 837; 1716 100 838; 1717 101 839
353. 1718 102 840; 1719 103 841; 1720 104 842; 1721 105 843; 1722 106
844
354. 1723 107 845; 1724 108 846; 1725 109 847; 1726 110 848; 1727 111
849
355. 1728 836 847; 1729 835 844; 1730 834 841; 1731 833 840; 1732 849
362
356. 1733 848 849; 1734 847 825; 1735 846 836; 1736 845 846; 1737 844
827
357. 1738 843 835; 1739 842 829; 1740 841 842; 1741 840 831; 1742 839
833
358. 1743 838 839; 1744 837 838; 1745 355 850; 1746 851 837; 1747 850
852
359. 1748 819 850; 1749 852 851; 1750 821 852; 1751 853 851; 1753 799
62
360. 1755 805 818; 1757 825 848; 1758 827 845; 1759 829 843; 1760 831
834
361. 1761 854 855; 1762 854 815; 1763 855 856; 1764 855 816; 1765 856
801
362. 1766 856 817; 1767 2 805; 1770 4 804; 1771 804 16; 1772 805 14;
1774 44 20
363. 1775 16 46; 1776 16 18; 1777 14 20; 1778 22 68; 1779 66 26; 1780
26 161
364. 1781 68 30; 1782 26 32; 1783 28 30; 1784 24 26; 1785 22 28; 1786
18 24
365. 1787 20 22; 1788 20 48; 1789 46 24; 1790 24 50; 1791 48 28; 1792
28 52
366. 1793 50 32; 1794 32 250; 1795 52 242; 1796 40 851; 1797 308 813;
1798 638 752
367. 1799 609 803; 1800 803 653; 1801 752 652; 1802 152 14; 1803 153
152
368. 1804 154 153; 1805 816 817; 1806 817 807; 1807 804 816; 1808 807
154
369. 1809 52 404; 1810 362 403; 1811 200 202; 1812 208 194; 1813 194
203
370. 1814 202 195; 1815 195 432; 1816 203 433; 1817 433 784; 1818 432
785
371. 1819 785 763; 1820 784 764; 1821 764 207; 1822 763 199; 1823 199
382
372. 1824 207 383; 1825 383 392; 1826 382 393; 1827 393 402; 1828 392
403
373. 1829 403 205; 1830 402 197; 1831 197 287; 1832 286 205; 1833 286
209
374. 1834 201 287; 1835 405 395; 1836 404 394; 1837 403 393; 1838 399
389
STAAD SPACE -- PAGE NO.
8
375. 1839 406 396; 1840 445 447; 1841 460 462; 1842 475 477; 1843 490
492
376. 1844 505 507; 1845 520 522; 1846 535 537; 1847 550 552; 1848 565
567
377. 1849 580 582; 1850 5 857; 1851 7 858; 1852 13 859; 1853 15 860;
1854 21 861
378. 1855 23 862; 1856 25 863; 1857 27 864; 1858 29 865; 1859 31 866;
1860 169 867
379. 1861 170 868; 1862 176 869; 1863 177 870; 1864 184 871; 1865 185
872
380. 1866 192 873; 1867 193 874; 1868 200 875; 1869 201 876; 1870 208
877
381. 1871 209 878; 1872 216 879; 1873 224 880; 1874 225 881; 1875 232
882
382. 1876 233 883; 1877 240 884; 1878 241 885; 1879 243 886; 1880 245
887
383. 1881 247 888; 1882 248 889; 1883 249 890; 1884 251 891; 1885 252
892
384. 1886 254 893; 1887 255 894; 1888 256 895; 1889 257 896; 1890 305
897
385. 1891 306 898; 1892 312 899; 1893 321 900; 1894 326 901; 1895 331
902
386. 1896 336 903; 1897 346 904; 1898 353 905; 1899 366 906; 1900 376
907
387. 1901 451 908; 1902 452 909; 1903 466 910; 1904 467 911; 1905 481
912
388. 1906 482 913; 1907 496 914; 1908 497 915; 1909 511 916; 1910 512
917
389. 1911 526 918; 1912 527 919; 1913 541 920; 1914 542 921; 1915 556
922
390. 1916 557 923; 1917 571 924; 1918 586 925; 1919 587 926; 1920 605
927
391. 1921 606 928; 1922 608 929; 1923 610 930; 1924 612 931; 1925 616
932
392. 1926 618 933; 1927 620 934; 1928 637 935; 1929 651 936; 1930 800
937
393. 1931 802 938; 1932 812 939; 1933 822 940; 1934 823 941; 1935 824
942
394. 1936 826 943; 1937 828 944; 1938 830 945; 1939 832 946; 1940 853
947
395. 1941 184 251; 1942 251 252; 1943 252 800; 1944 800 951; 1945 254
255
396. 1946 255 256; 1947 256 257; 1948 257 185; 1949 185 170; 1950 170
177
397. 1951 177 955; 1952 193 956; 1953 201 957; 1954 209 225; 1955 225
233
398. 1956 233 241; 1957 241 306; 1958 306 452; 1959 452 467; 1960 467
482
399. 1961 482 497; 1962 497 512; 1963 512 527; 1964 527 542; 1965 542
557
400. 1966 557 587; 1967 587 606; 1968 184 169; 1969 169 176; 1970 176
192
401. 1971 192 969; 1972 200 963; 1973 208 216; 1974 216 949; 1975 224
232
402. 1976 232 240; 1977 240 305; 1978 305 451; 1979 451 466; 1980 466
481
403. 1981 481 496; 1982 496 511; 1983 511 526; 1984 526 541; 1985 541
556
404. 1986 556 571; 1987 571 586; 1988 586 605; 1989 605 608; 1990 608
610
405. 1991 610 948; 1992 612 616; 1993 616 618; 1994 618 620; 1995 620
606
406. 1996 586 637; 1997 637 802; 1998 802 651; 1999 948 612; 2000 651
948
407. 2001 257 29; 2002 29 31; 2003 31 961; 2004 31 953; 2005 249 954;
2006 366 376
408. 2008 249 248; 2009 248 247; 2010 247 824; 2011 824 245; 2012 245
812
409. 2013 812 243; 2014 243 965; 2015 243 312; 2016 312 964; 2017 353
346
410. 2018 346 950; 2019 321 326; 2020 326 331; 2021 331 336; 2022 305
336
411. 2023 240 331; 2024 232 326; 2025 949 224; 2026 950 321; 2027 949
950
412. 2028 208 353; 2029 200 977; 2030 245 959; 2031 15 13; 2032 951
952
413. 2033 951 13; 2034 823 960; 2035 822 823; 2036 952 979; 2038 953
249
414. 2039 954 366; 2040 955 193; 2041 953 962; 2042 956 201; 2043 954
956
415. 2044 957 209; 2045 376 957; 2046 13 822; 2047 822 980; 2048 979
980
416. 2049 958 21; 2050 959 15; 2051 960 824; 2052 959 960; 2053 961
177
417. 2054 962 955; 2055 961 962; 2056 963 208; 2057 964 353; 2058 963
975
418. 2059 965 967; 2060 966 312; 2061 965 974; 2062 967 192; 2063 968
978
419. 2064 967 970; 2065 969 971; 2066 970 972; 2067 971 973; 2068 972
981
420. 2069 969 970; 2070 971 972; 2071 973 200; 2072 974 966; 2073 973
981
421. 2074 975 976; 2075 976 964; 2076 977 968; 2077 978 966; 2078 977
975
422. 2079 978 976; 2080 979 254; 2081 980 958; 2082 981 968; 2083 981
974
423. START GROUP DEFINITION
424. MEMBER
425. _FULLFRAME 261 TO 263 268 TO 273 275 TO 277 282 TO 284 289 TO 291
296 TO 300 -
426. 303 304 310 TO 312 317 TO 319 324 TO 326 330 349 368 369 371 TO
374 386 409 -
427. 412 415 416 418 TO 421 424 425 427 TO 430 432 433 460 461 463 473
TO 476 -
428. 618 638 678 808 TO 811 832 833 835 852 853 856 TO 859 864 866 870
-
429. 880 TO 883 904 TO 907 928 TO 931 952 TO 955 976 TO 979 1000 1001
-
430. 1024 TO 1027 1044 1047 1048 1106 TO 1114 1116 TO 1118 1130 1143
1144 1148 -
STAAD SPACE -- PAGE NO.
9
431. 1149 TO 1153 1191 1192 1298 1299 1302 1303 1305 1310 1311 1314
1315 1317 1322 -
432. 1323 1326 1327 1329 1334 1335 1338 1339 1341 1346 1347 1350 1351
1353 1358 -
433. 1359 1362 1363 1365 1370 1371 1374 1375 1377 1382 1383 1386 1387
1389 1394 -
434. 1395 1398 1399 1401 1406 1407 1410 1411 1413 1418 1419 1422 1423
1425 1430 -
435. 1431 1434 1435 1437 1442 1443 1446 1447 1449 1454 1455 1458 1459
1461 1466 -
436. 1467 1470 1471 1473 1478 1479 1482 1483 1485 1490 1491 1494 1495
1497 1502 -
437. 1503 1506 1507 1509 1514 TO 1516 1545 1591 1592 1594 1595 1597
1599 1601 -
438. 1603 1605 1607 1610 1612 1614 1616 1618 1620 1622 1624 1626 1628
1630 1633 -
439. 1634
440. _PLINTHBEAMS 1941 TO 2006 2008 TO 2036 2038 TO 2083
441. _PEDESTALS 1850 TO 1940
442. END GROUP DEFINITION
443. ***
444. DEFINE MATERIAL START
445. ISOTROPIC STEEL
446. E 2.05E+008
447. POISSON 0.3
448. DENSITY 76.8195
449. ALPHA 1.2E-005
450. DAMP 0.03
451. TYPE STEEL
452. STRENGTH FY 253200 FU 407800 RY 1.5 RT 1.2
453. ISOTROPIC CONCRETE
454. E 2.17185E+007
455. POISSON 0.17
456. DENSITY 23.5616
457. ALPHA 1E-005
458. DAMP 0.05
459. TYPE CONCRETE
460. STRENGTH FCU 27579
461. END DEFINE MATERIAL
462. MEMBER PROPERTY AMERICAN
463. 21 TO 25 29 TO 32 165 TO 177 186 TO 195 338 TO 343 345 TO 348 350
TO 365 367 -
464. 375 TO 381 390 TO 399 487 TO 490 497 TO 500 507 TO 510 517 TO 520
-
465. 527 TO 530 537 TO 540 557 TO 560 563 565 567 569 571 572 575 581
TO 584 596 -
466. 597 TO 599 1119 1126 TO 1129 1156 TO 1159 1166 TO 1169 1176 1182
1188 1189 -
467. 1541 1635 1672 1675 1676 1686 1697 1701 1728 TO 1747 1749 1753
1757 TO 1761 -
468. 1763 1765 TAPERED 0.42 0.005 0.42 0.25 0.01
469. 74 75 88 TO 92 140 142 144 146 148 150 152 223 TO 237 239 241 250
252 411 -
470. 576 TO 579 585 591 TO 594 1713 1714 1721 TO 1726 -
471. 1727 TAPERED 0.316 0.005 0.316 0.15 0.006
472. MEMBER PROPERTY AMERICAN
473. 72 73 82 TO 87 134 136 138 201 TO 206 211 TO 222 244 327 328 407
481 TO 485 -
474. 491 TO 495 501 TO 505 511 TO 515 521 TO 525 542 544 546 548 550
562 564 566 -
475. 568 570 574 1160 TO 1164 1173 1175 1177 1183 1190 1674 1684 1691
1693 1698 -
476. 1699 1702 1703 1711 1712 1715 TO 1720 1748 1750 1762 1764 -
477. 1766 TAPERED 0.212 0.005 0.212 0.15 0.006
478. MEMBER PROPERTY AMERICAN
479. 3 4 7 8 11 TO 16 331 333 335 TO 337 486 496 506 516 526 536 556
580 595 1155 -
480. 1181 1673 1687 1704 TO 1710 1751 1809 -
481. 1810 TAPERED 0.32 0.005 0.32 0.2 0.01
482. 290 291 297 304 311 318 319 325 326 474 475 809 810 833 857 858
881 882 905 -
483. 906 929 930 953 954 977 978 1001 1025 1026 -
484. 1514 TAPERED 0.524 0.006 0.688 0.25 0.012
485. 289 296 303 310 317 324 409 429 433 473 476 808 811 832 835 856
859 880 883 -
486. 904 907 928 931 952 955 976 1000 1024 TAPERED 0.688 0.006 0.874
0.25 0.012
STAAD SPACE -- PAGE NO.
10
599. SUPPORTS
600. 857 TO 947 FIXED
601. MEMBER RELEASE
602. 19 25 32 72 TO 75 82 TO 92 134 136 138 140 142 144 146 148 150
152 -
603. 201 TO 206 211 TO 237 239 241 244 250 252 259 327 328 338 405 TO
407 411 -
604. 413 414 434 TO 449 455 456 460 477 478 480 TO 485 487 491 TO 495
497 501 -
605. 502 TO 505 507 511 TO 515 517 521 TO 525 527 537 541 TO 550 557
562 564 566 -
606. 568 570 573 574 576 TO 579 585 591 TO 594 600 601 612 632 652 712
-
607. 812 TO 814 836 TO 838 860 TO 862 884 TO 886 908 TO 910 932 TO 934
-
608. 956 TO 958 980 TO 982 1004 1005 1028 1029 1044 1097 1098 1156
1160 TO 1164 -
609. 1166 1173 1175 1177 1183 1190 1196 TO 1203 1205 TO 1207 1551 1593
1674 1684 -
610. 1691 1693 1698 1699 1702 1703 1711 TO 1727 1748 1750 1755 1762
1764 1766 -
611. 1807 START MY MZ
612. 72 TO 75 82 TO 92 134 136 138 140 142 144 146 148 150 152 165 178
201 TO 206 -
613. 211 TO 237 239 241 244 250 252 327 328 350 386 405 TO 407 411 413
TO 416 -
614. 418 TO 421 434 TO 449 455 456 462 464 477 478 480 TO 485 491 TO
495 -
615. 501 TO 505 511 TO 515 521 TO 525 541 TO 550 562 564 566 568 570
573 574 576 -
616. 577 TO 579 582 585 591 TO 594 597 731 812 TO 814 836 TO 838 860
TO 862 884 -
617. 885 TO 886 908 TO 910 932 TO 934 956 TO 958 980 TO 982 1004 1005
1028 1029 -
618. 1045 1046 1097 TO 1102 1105 1130 1143 1148 1149 1160 TO 1164 1173
1175 1177 -
619. 1183 1190 TO 1192 1196 TO 1203 1205 TO 1207 1243 1244 1590 1632
1633 1674 -
620. 1684 1691 1693 1698 1699 1702 1703 1711 TO 1727 1748 1750 1762
1764 1766 -
621. 1802 1809 1810 END MY MZ
622. 3 4 7 8 11 TO 16 262 263 269 270 276 277 283 284 290 291 297 298
304 311 312 -
623. 318 319 325 326 331 333 335 TO 337 368 369 371 TO 374 474 475 486
496 506 -
624. 516 526 536 556 580 595 809 810 833 857 858 881 882 905 906 929
930 953 954 -
625. 977 978 1001 1025 1026 1110 TO 1114 1116 TO 1118 1155 1181 1514
1634 1673 -
626. 1687 1704 TO 1710 1751 START MX MY MZ
627. 2048 END MX MY MZ
628. MEMBER TENSION
629. 732 TO 737 744 TO 755 780 TO 785 792 TO 803 1049 TO 1054 1061 TO
1078 1085 -
630. 1086 TO 1096 1517 TO 1522 1529 TO 1540 1636 TO 1641 1648 TO 1671
1811 TO 1834
631. LOAD 3 LOADTYPE DEAD TITLE DL
632.
*************************************************************************
******
633.
*************************************************************************
******
634. **MEZZANINE
635. ** ASSUME THICKNESS OF SLAB = 125MM
636. ** 0.125*25 = 3.125 KN/M2
637. ** FF = 1 KN/M2
638. **DL = 4.125 KN/M2
639. ** LL = 10 KN/M2
640. ** TOTAL LOAD = (14.125)*1.5 = 21.2KN/M
641. *** DECKING PROFILE
642. **CONSIDERED DECKING PROFILE - 52/324
643. ** SPACING OF SECONDARY MEMBERS = 1.3M
644. ** DECKING SHEET THICK = 1MM = 10.02 KG/M2
645. ** 10.02*1.5 = 15.03KG/M = 0.15KN/M
646. ** TOTAL DL ON SB = 21.2+0.15 = 21.35KN/M
647. SELFWEIGHT Y -1.15 LIST 3 4 7 8 11 TO 16 19 21 TO 25 27 29 TO 32
34 -
648. 72 TO 75 82 TO 92 134 136 138 140 142 144 146 148 150 152 159 TO
180 186 -
649. 187 TO 195 201 TO 206 211 TO 237 239 241 244 250 252 259 261 TO
263 -
650. 268 TO 273 275 TO 277 282 TO 284 289 TO 291 296 TO 300 303 304
310 TO 312 -
651. 317 TO 319 324 TO 328 330 331 333 335 TO 343 345 TO 365 367 TO
369 -
652. 371 TO 381 386 390 TO 399 405 TO 407 409 411 TO 416 418 TO 421
424 425 427 -
653. 428 TO 430 432 TO 449 455 456 460 TO 464 473 TO 478 480 TO 530
536 TO 550 -
654. 556 TO 560 562 TO 585 591 TO 610 612 615 617 TO 619 621 623 625
627 628 630 -
STAAD SPACE -- PAGE NO.
13
655. 632 635 637 TO 639 641 643 645 647 648 650 652 655 657 659 661
663 665 667 -
656. 668 670 678 712 715 717 719 721 723 725 727 728 730 TO 737 744 TO
755 780 -
657. 781 TO 785 792 TO 803 808 TO 815 817 819 821 827 832 833 835 TO
839 841 843 -
658. 845 851 TO 853 856 TO 867 869 870 875 880 TO 887 889 891 893 899
904 TO 911 -
659. 913 915 917 923 928 TO 935 937 939 941 947 952 TO 959 961 963 965
971 976 -
660. 977 TO 983 985 987 989 995 1000 1001 1004 1005 1007 1009 1011
1013 1019 1024 -
661. 1025 TO 1029 1031 1033 1035 1037 1043 TO 1054 1061 TO 1078 1085
TO 1102 1105 -
662. 1106 TO 1114
663. SELFWEIGHT Y -1.15 LIST 1116 TO 1119 1126 TO 1130 1143 1144 1148
TO 1153 1155 -
664. 1156 TO 1164 1166 TO 1169 1173 1175 TO 1177 1181 TO 1183 1188 TO
1192 1196 -
665. 1197 TO 1203 1205 TO 1207 1243 1244 1272 TO 1291 1296 1298 1299
1302 1303 -
666. 1305 1308 1310 1311 1314 1315 1317 1320 1322 1323 1326 1327 1329
1332 1334 -
667. 1335 1338 1339 1341 1344 1346 1347 1350 1351 1353 1356 1358 1359
1362 1363 -
668. 1365 1368 1370 1371 1374 1375 1377 1380 1382 1383 1386 1387 1389
1392 1394 -
669. 1395 1398 1399 1401 1404 1406 1407 1410 1411 1413 1416 1418 1419
1422 1423 -
670. 1425 1428 1430 1431 1434 1435 1437 1440 TO 1443 1446 1447 1449
1452 TO 1455 -
671. 1458 1459 1461 1464 TO 1467 1470 1471 1473 1476 1478 1479 1482
1483 1485 -
672. 1488 1490 1491 1494 1495 1497 1500 1502 1503 1506 1507 1509 1512
TO 1522 -
673. 1529 TO 1541 1545 1551 1554 1556 1558 1560 1562 1564 1566 1567
1569 1571 -
674. 1573 1575 1577 1579 1581 1583 1585 1587 1589 TO 1641 1648 TO 1676
1684 1686 -
675. 1687 1691 1693 1696 TO 1751 1753 1755 1757 TO 1767 1770 TO 1772
1774 TO 1810 -
676. 1813 TO 1832 1835 TO 1849
677. **MEZZANINE
678. ** ASSUME THICKNESS OF SLAB = 125MM
679. ** 0.125*25 = 3.125 KN/M2
680. ** FF = 1 KN/M2
681. **DL = 4.125 KN/M2
682. ** = 4.125*1.4 = 6.2KN/M
683. *** DECKING PROFILE
684. **CONSIDERED DECKING PROFILE - 52/324
685. ** SPACING OF SECONDARY MEMBERS = 1.5M
686. ** DECKING SHEET THICK = 1MM = 10.02 KG/M2
687. ** 10.02*1.4 = 14.028KG/M = 0.14KN/M
688. ** TOTAL DL ON SB = 6.2+0.14 = 6.34KN/M
689. MEMBER LOAD
690. 72 TO 75 82 TO 92 134 136 138 140 142 144 146 148 150 152 201 TO
206 -
691. 211 TO 237 239 241 250 252 327 328 481 TO 485 491 TO 495 501 TO
505 -
692. 511 TO 515 521 TO 525 541 TO 550 562 564 566 568 570 573 574 576
TO 579 591 -
693. 592 TO 594 1160 TO 1164 1173 1175 1177 1183 1190 1674 1691 1693
1698 1699 -
694. 1702 1703 1711 TO 1727 1748 1750 UNI GY -6.34
695. *****
696. MEMBER LOAD
697. ***RAFTERS***
698. 299 300 618 638 678 1515 1516 1599 UNI GY -4
699. **
700. 271 TO 273 424 425 427 428 1106 TO 1108 1150 TO 1153 1545 1591
UNI GY -1.7
701. ***COLUMNS***
702. 261 268 275 282 289 296 303 310 317 324 330 349 386 409 412 415
416 -
703. 418 TO 421 429 430 432 433 460 461 463 473 476 808 811 832 835
856 859 880 -
704. 883 904 907 928 931 952 955 976 979 1000 1024 1027 1044 1047 1048
1109 1130 -
705. 1143 1144 1148 1149 1191 1192 1633 1809 1810 UNI GY -0.92
706. MEMBER LOAD
707. 852 853 864 866 870 1296 1298 1299 1302 1303 1305 1308 1310 1311
1314 1315 -
708. 1317 1320 1322 1323 1326 1327 1329 1332 1334 1335 1338 1339 1341
1344 1346 -
709. 1347 1350 1351 1353 1356 1358 1359 1362 1363 1365 1368 1370 1371
1374 1375 -
710. 1377 1380 1382 1383 1386 1387 1389 1392 1394 1395 1398 1399 1401
1404 1406 -
STAAD SPACE -- PAGE NO.
14
711. 1407 1410 1411 1413 1416 1418 1419 1422 1423 1425 1428 1430 1431
1434 1435 -
712. 1437 1440 TO 1443 1446 1447 1449 1452 TO 1455 1458 1459 1461 1464
TO 1467 -
713. 1470 1471 1473 1476 1478 1479 1482 1483 1485 1488 1490 1491 1494
1495 1497 -
714. 1500 1502 1503 1506 1507 1509 1512 1513 1592 1594 1595 1597 1601
1603 1605 -
715. 1607 1610 1612 1614 1616 1618 1620 1622 1624 1626 1628 1630 1835
TO 1848 -
716. 1849 UNI GY -3.4
717. 411 585 600 UNI GY -3.17
718. JOINT LOAD
719. 2 4 178 186 194 202 210 218 226 234 242 250 265 270 271 286 287
289 290 304 -
720. 307 450 453 465 468 480 483 495 498 510 513 525 528 540 543 555
558 570 585 -
721. 588 604 607 FY -0.713
722. MEMBER LOAD
723. 1867 1941 TO 1952 1968 TO 1991 1996 TO 2006 2008 TO 2029 2032
2036 -
724. 2038 TO 2043 2045 2053 2054 2056 2057 2059 2060 2062 2063 2065
2067 2071 -
725. 2076 2077 2080 UNI GY -24.4
726. 1953 2044 UNI GY -18
727. 1910 1955 TO 1967 1993 TO 1995 2030 2033 TO 2035 2046 TO 2048
2050 TO 2052 -
728. 2055 2058 2061 2064 2066 2068 TO 2070 2072 TO 2075 2078 2079 2081
TO 2082 -
729. 2083 UNI GY -13.6
730. SELFWEIGHT Y -1 LIST 1850 TO 2006 2008 TO 2036 2038 TO 2081
731. LOAD 4 LOADTYPE LIVE REDUCIBLE TITLE LL
732. MEMBER LOAD
733. 74 75 88 TO 92 140 142 144 146 148 150 152 223 TO 237 239 241 250
252 576 -
734. 577 TO 579 591 TO 594 1713 1714 1721 TO 1727 UNI GY -14
735. 72 73 82 TO 87 134 136 138 201 TO 206 211 TO 222 327 328 481 TO
485 -
736. 491 TO 495 501 TO 505 511 TO 515 521 TO 525 541 TO 550 562 564
566 568 570 -
737. 573 574 1160 TO 1164 1173 1175 1177 1183 1190 1674 1691 1693 1698
1699 1702 -
738. 1703 1711 1712 1715 TO 1720 1748 1750 UNI GY -5.6
739. ***
740.
*************************************************************************
******
741. ***LOAD CALCULATIONS*****
742. **** CODE = (SANS 10160 - TABLE - 5)
743. **LIVE LOAD ON ROOF = 0.25 KN/M2
744. **LL ON RAFTER = 1.452 KN/M
745.
*************************************************************************
******
746. MEMBER LOAD
747. 299 300 618 638 678 1515 1516 1599 UNI GY -1.425
748. *
749. 271 TO 273 424 425 427 428 1106 TO 1108 1150 TO 1153 1545 1591
UNI GY -0.625
750. MEMBER LOAD
751. 852 853 864 866 870 1296 1298 1299 1302 1303 1305 1308 1310 1311
1314 1315 -
752. 1317 1320 1322 1323 1326 1327 1329 1332 1334 1335 1338 1339 1341
1344 1346 -
753. 1347 1350 1351 1353 1356 1358 1359 1362 1363 1365 1368 1370 1371
1374 1375 -
754. 1377 1380 1382 1383 1386 1387 1389 1392 1394 1395 1398 1399 1401
1404 1406 -
755. 1407 1410 1411 1413 1416 1418 1419 1422 1423 1425 1428 1430 1431
1434 1435 -
756. 1437 1440 TO 1443 1446 1447 1449 1452 TO 1455 1458 1459 1461 1464
TO 1467 -
757. 1470 1471 1473 1476 1478 1479 1482 1483 1485 1488 1490 1491 1494
1495 1497 -
758. 1500 1502 1503 1506 1507 1509 1512 1513 1592 1594 1595 1597 1601
1603 1605 -
759. 1607 1610 1612 1614 1616 1618 1620 1622 1624 1626 1628 1630 1835
TO 1848 -
760. 1849 UNI GY -1.25
761. 411 585 600 UNI GY -7
762. JOINT LOAD
763. 2 4 178 186 194 202 210 218 226 234 242 250 265 270 271 286 287
289 290 304 -
764. 307 450 453 465 468 480 483 495 498 510 513 525 528 540 543 555
558 570 585 -
765. 588 604 607 FY -3
766. **
STAAD SPACE -- PAGE NO.
15
823. 1470 1471 1473 1476 1478 1479 1482 1483 1485 1488 1490 1491 1494
1495 1497 -
824. 1500 1502 1503 1506 1507 1509 1512 1513 1592 1594 1595 1597 1601
1603 1605 -
825. 1607 1610 1612 1614 1616 1618 1620 1622 1624 1626 1628 1630 1835
TO 1848 -
826. 1849 UNI Y 3.6
827. 261 268 282 289 296 310 317 324 473 808 832 856 880 904 928 952
976 1000 -
828. 1024 UNI GX -4.6
829. 330 349 409 412 429 430 433 461 463 476 811 835 859 883 907 931
955 1044 1047 -
830. 1048 1809 1810 UNI GX 4.6
831.
*************************************************************************
******
832. LOAD 7 LOADTYPE WIND TITLE WL Z (180- DEGREE)
833.
*************************************************************************
******
834. MEMBER LOAD
835. 299 618 638 678 1515 1516 1599 UNI Y 8.15
836. 271 273 424 425 427 428 1106 1108 1150 TO 1153 1545 1591 UNI Y
3.6
837. 272 1107 UNI Y 3.6 2 5.26613
838. 303 UNI GX -5.22
839. 460 UNI GX -5.22
840. 415 416 418 TO 421 1633 UNI GZ -9.15
841. 275 386 UNI GZ -4.575
842. 272 1107 UNI Y 6.275 0 2
843. 386 1130 UNI GX -2.3
844. 275 1109 UNI GX -2.3
845. 300 UNI Y 8.15 2 5.226
846. 300 853 1299 1311 1323 1335 1347 1359 1371 1383 1395 1407 1419
1431 1443 1455 -
847. 1467 1479 1491 1503 UNI Y 12.55 0 2
848. 852 864 866 870 1296 1298 1302 1303 1305 1308 1310 1314 1315 1317
1320 1322 -
849. 1326 1327 1329 1332 1334 1338 1339 1341 1344 1346 1350 1351 1353
1356 1358 -
850. 1362 1363 1365 1368 1370 1374 1375 1377 1380 1382 1386 1387 1389
1392 1394 -
851. 1398 1399 1401 1404 1406 1410 1411 1413 1416 1418 1422 1423 1425
1428 1430 -
852. 1434 1435 1437 1440 TO 1442 1446 1447 1449 1452 TO 1454 1458 1459
1461 1464 -
853. 1465 TO 1466 1470 1471 1473 1476 1478 1482 1483 1485 1488 1490
1494 1495 1497 -
854. 1500 1502 1506 1507 1509 1512 1513 1592 1594 1595 1597 1601 1603
1605 1607 -
855. 1610 1612 1614 1616 1618 1620 1622 1624 1626 1628 1630 1835 TO
1848 -
856. 1849 UNI Y 7.15
857. 853 1299 1311 1323 1335 1347 1359 1371 1383 1395 1407 1419 1431
1443 1455 -
858. 1467 1479 1491 1503 UNI Y 7.15 2 5.226
859. 261 268 282 289 296 310 317 324 330 349 409 412 429 430 432 433
461 463 473 -
860. 476 808 811 832 835 856 859 880 883 904 907 928 931 952 955 976
1000 1024 -
861. 1044 1047 1048 1809 1810 UNI GX -4.6
862. 1143 1144 1148 1149 1191 1192 UNI GZ 9.15
863. 1109 1130 UNI GZ 4.575
864.
*************************************************************************
******
865. LOAD 8 LOADTYPE WIND TITLE WL Z (270- DEGREE)
866.
*************************************************************************
******
867. MEMBER LOAD
868. 299 300 618 638 678 1515 1516 1599 UNI Y 6.18
869. 460 UNI GX 7.32
870. 415 416 418 TO 421 1633 UNI GZ -1.83
871. 275 386 UNI GZ -0.915
872. 271 TO 273 424 425 427 428 1106 TO 1108 1150 TO 1153 1545 1591
UNI Y 2.71
873. 386 1130 UNI GX 3.2
874. 852 853 864 866 870 1296 1298 1299 1302 1303 1305 1308 1310 1311
1314 1315 -
875. 1317 1320 1322 1323 1326 1327 1329 1332 1334 1335 1338 1339 1341
1344 1346 -
876. 1347 1350 1351 1353 1356 1358 1359 1362 1363 1365 1368 1370 1371
1374 1375 -
877. 1377 1380 1382 1383 1386 1387 1389 1392 1394 1395 1398 1399 1401
1404 1406 -
878. 1407 1410 1411 1413 1416 1418 1419 1422 1423 1425 1428 1430 1431
1434 1435 -
STAAD SPACE -- PAGE NO.
17
879. 1437 1440 TO 1443 1446 1447 1449 1452 TO 1455 1458 1459 1461 1464
TO 1467 -
880. 1470 1471 1473 1476 1478 1479 1482 1483 1485 1488 1490 1491 1494
1495 1497 -
881. 1500 1502 1503 1506 1507 1509 1512 1513 1592 1594 1595 1597 1601
1603 1605 -
882. 1607 1610 1612 1614 1616 1618 1620 1622 1624 1626 1628 1630 1835
TO 1848 -
883. 1849 UNI Y 5.42
884. 330 349 409 412 429 430 432 433 461 463 476 811 835 859 883 907
931 955 979 -
885. 1027 1044 1047 1048 1809 1810 UNI GX 6.4
886. 261 268 282 289 296 310 317 324 473 808 832 856 880 904 928 952
976 1000 -
887. 1024 UNI GX -6.4
888. 275 1109 UNI GX -3.2
889. 1143 1144 1148 1149 1191 1192 UNI GZ -7.32
890. 1109 1130 UNI GZ -3.66
891.
*************************************************************************
******
892. ********************************WIND LOAD AS PER IS 875 PART
III***************
893.
*************************************************************************
******
894. ***LOAD CALCULATIONS***
895. ** LOCATION = SOUTH AFRICA
896. **BASIC WIND SPEED = 36.11 M/S
897. *************************************
898. *************************************
899. *************************************
900.
*************************************************************************
******
901. ********************************LOAD
COMBINATIONS******************************
902.
*************************************************************************
******
903. LOAD COMB 101 1.35DL 1.5LL
904. 3 1.35 4 1.5
905. LOAD COMB 102 1DL 1.5LL 0.75WL(X+CPI)
906. 5 0.75 3 1.0 4 1.5
907. LOAD COMB 103 1DL 1.5LL 0.75WL(X-CPI)
908. 6 0.75 3 1.0 4 1.5
909. LOAD COMB 104 1DL 1.5LL 0.75WL(Z+CPI)
910. 7 0.75 3 1.0 4 1.5
911. LOAD COMB 105 1DL 1.5LL 0.75WL(Z-CPI)
912. 8 0.75 3 1.0 4 1.5
913. LOAD COMB 106 1DL 1.05LL 1.5WL(X+CPI)
914. 3 1.0 4 1.05 5 1.5
915. LOAD COMB 107 1DL 1.05LL 1.5WL(X-CPI)
916. 3 1.0 4 1.05 6 1.5
917. LOAD COMB 108 1DL 1.05LL 1.5WL(Z+CPI)
918. 3 1.0 4 1.05 7 1.5
919. LOAD COMB 109 1DL 1.05LL 1.5WL(Z-CPI)
920. 3 1.0 4 1.05 8 1.5
921. LOAD COMB 201 1DL 0.3LL
922. 3 1.0 4 0.3
923. LOAD COMB 202 1DL 0.3LL 0.2WL+X
924. 3 1.0 5 0.2 4 0.3
925. LOAD COMB 203 1DL 0.3LL 0.2WL-X
926. 3 1.0 6 0.2 4 0.3
927. LOAD COMB 204 1DL 0.3LL 0.2WL+Z
928. 3 1.0 7 0.2 4 0.3
929. LOAD COMB 205 1DL 0.3LL 0.2WL-Z
930. 3 1.0 8 0.2 4 0.3
931. LOAD COMB 206 1DL 0.7LL 1WL(X+CPI)
932. 3 1.0 4 0.7 5 1.0
933. LOAD COMB 207 1DL 0.7LL 1WL(X-CPI)
934. 3 1.0 4 0.7 6 1.0
STAAD SPACE -- PAGE NO.
18
P R O B L E M S T A T I S T I C S
-----------------------------------
950.
*************************************************************************
******
951. ********************************LOAD
ENVELOPES*********************************
952.
*************************************************************************
******
953. DEFINE ENVELOPE
954.
***********************************************************************
955. **************************STRENGTH
ENVELOPES****************************
956.
***********************************************************************
957. 101 TO 109 ENVELOPE 1 TYPE STRENGTH
958.
***********************************************************************
959. **************************SERVICE
ENVELOPES***************************
960.
***********************************************************************
961. 201 TO 205 ENVELOPE 2 TYPE SERVICEABILITY
962. END DEFINE ENVELOPE
963.
***********************************************************************
964.
***********************************************************************
965. PARAMETER 1
966. CODE AISC
967. FU 490000 MEMB 3 4 7 8 11 TO 16 19 21 TO 25 27 29 TO 32 34 72 TO
75 -
968. 82 TO 92 134 136 138 140 142 144 146 148 150 152 159 TO 180 186
TO 195 201 -
969. 202 TO 206 211 TO 237 239 241 244 250 252 259 261 TO 263 268 TO
273 -
970. 275 TO 277 282 TO 284 289 TO 291 296 TO 300 303 304 310 TO 312
317 TO 319 -
971. 324 TO 328 330 331 333 335 TO 343 345 TO 365 368 369 371 TO 381
386 -
972. 390 TO 399 405 TO 407 409 411 TO 416 418 TO 421 424 425 427 TO
430 -
973. 432 TO 449 455 456 460 TO 464 473 TO 478 480 TO 530 536 TO 550
556 TO 560 -
974. 562 TO 585 591 TO 610 612 615 617 TO 619 621 623 625 627 628 630
632 635 -
975. 637 TO 639 641 643 645 647 648 650 652 655 657 659 661 663 665
667 668 670 -
976. 678 712 715 717 719 721 723 725 727 728 730 731 808 TO 815 817
819 821 827 -
977. 832 833 835 TO 839 841 843 845 851 TO 853 856 TO 867 869 870 875
880 TO 887 -
978. 889 891 893 899 904 TO 911 913 915 917 923 928 TO 935 937 939 941
947 952 -
979. 953 TO 959 961 963 965 971 976 TO 983 985 987 989 995 1000 1001
1004 1005 -
980. 1007 1009 1011 1013 1019 1551 1554 1556 1558 1560 1562 1564 1566
1567 1569 -
981. 1571 1573 1575 1577 1579 1581 1583 1585 1587 1591 1593 1596 1598
TO 1600 -
STAAD SPACE -- PAGE NO.
20
1094. 1434 1435 1437 1440 TO 1443 1446 1447 1449 1452 TO 1455 1458 1459
1461 1464 -
1095. 1465 TO 1467 1470 1471 1473 1476 1478 1479 1482 1483 1485 1488
1490 1491 1494 -
1096. 1495 1497 1500 1502 1503 1506 1507 1509 1512 1513 1515 1516 1545
1591 1592 -
1097. 1594 1595 1597 1599 1601 1603 1605 1607 1610 1612 1614 1616 1618
1620 1622 -
1098. 1624 1626 1628 1630 1835 TO 1849
1099. LX 1.5 MEMB 271 TO 273 299 300 424 425 427 428 618 638 678 852
853 864 866 -
1100. 870 1106 TO 1108 1150 TO 1153 1296 1298 1299 1302 1303 1305 1308
1310 1311 -
1101. 1314 1315 1317 1320 1322 1323 1326 1327 1329 1332 1334 1335 1338
1339 1341 -
1102. 1344 1346 1347 1350 1351 1353 1356 1358 1359 1362 1363 1365 1368
1370 1371 -
1103. 1374 1375 1377 1380 1382 1383 1386 1387 1389 1392 1394 1395 1398
1399 1401 -
1104. 1404 1406 1407 1410 1411 1413 1416 1418 1419 1422 1423 1425 1428
1430 1431 -
1105. 1434 1435 1437 1440 TO 1443 1446 1447 1449 1452 TO 1455 1458 1459
1461 1464 -
1106. 1465 TO 1467 1470 1471 1473 1476 1478 1479 1482 1483 1485 1488
1490 1491 1494 -
1107. 1495 1497 1500 1502 1503 1506 1507 1509 1512 1513 1515 1516 1545
1591 1592 -
1108. 1594 1595 1597 1599 1601 1603 1605 1607 1610 1612 1614 1616 1618
1620 1622 -
1109. 1624 1626 1628 1630 1835 TO 1849
1110. LX 1.5 MEMB 261 268 275 282 289 296 303 310 317 324 330 349 386
409 412 415 -
1111. 416 418 TO 421 429 430 432 433 460 461 463 473 476 808 811 832
835 856 859 -
1112. 880 883 904 907 928 931 952 955 976 979 1000 1024 1027 1044 1047
1048 1109 -
1113. 1130 1143 1144 1148 1149 1191 1192 1633
1114. LY 1.5 MEMB 261 268 275 282 289 296 303 310 317 324 330 349 386
409 412 415 -
1115. 416 418 TO 421 429 430 432 433 460 461 463 473 476 808 811 832
835 856 859 -
1116. 880 883 904 907 928 931 952 955 976 979 1000 1024 1027 1044 1047
1048 1109 -
1117. 1130 1143 1144 1148 1149 1191 1192 1633
1118. UNT 1.5 MEMB 261 268 275 282 289 296 303 310 317 324 330 349 386
409 412 415 -
1119. 416 418 TO 421 429 430 432 433 460 461 463 473 476 808 811 832
835 856 859 -
1120. 880 883 904 907 928 931 952 955 976 979 1000 1024 1027 1044 1047
1048 1109 -
1121. 1130 1143 1144 1148 1149 1191 1192 1633
1122. UNB 1.5 MEMB 261 268 275 282 289 296 303 310 317 324 330 349 386
409 412 415 -
1123. 416 418 TO 421 429 430 432 433 460 461 463 473 476 808 811 832
835 856 859 -
1124. 880 883 904 907 928 931 952 955 976 979 1000 1024 1027 1044 1047
1048 1109 -
1125. 1130 1143 1144 1148 1149 1191 1192 1633
1126. LZ 29 MEMB 299 300 618 638 678 852 853 864 866 870 1296 1298 1299
1302 1303 -
1127. 1305 1308 1310 1311 1314 1315 1317 1320 1322 1323 1326 1327 1329
1332 1334 -
1128. 1335 1338 1339 1341 1344 1346 1347 1350 1351 1353 1356 1358 1359
1362 1363 -
1129. 1365 1368 1370 1371 1374 1375 1377 1380 1382 1383 1386 1387 1389
1392 1394 -
1130. 1395 1398 1399 1401 1404 1406 1407 1410 1411 1413 1416 1418 1419
1422 1423 -
1131. 1425 1428 1430 1431 1434 1435 1437 1440 TO 1443 1446 1447 1449
1452 TO 1455 -
1132. 1458 1459 1461 1464 TO 1467 1470 1471 1473 1476 1478 1479 1482
1483 1485 -
1133. 1488 1490 1491 1494 1495 1497 1500 1502 1503 1506 1507 1509 1512
1513 1515 -
1134. 1516 1592 1594 1595 1597 1599 1601 1603 1605 1607 1610 1612 1614
1616 1618 -
1135. 1620 1622 1624 1626 1628 1630 1835 TO 1849
1136. LZ 8.34 MEMB 1045 1046
1137. LZ 7.54 MEMB 19 27 34 159 TO 164 259 1243 1244
1138. LZ 11.4 MEMB 462 464
1139. LZ 4.74 MEMB 345 367 379 TO 381 399 563 1126 1166 TO 1169 1176
1182 1188 1189 -
1140. 1541 1672 1675 1676 1697 1701 1745 1747 1749 1753 1761 1763 1765
1141. LZ 7.18 MEMB 178 TO 180 1696 1700 1755 1802 TO 1808
1142. LZ 5 MEMB 24 31 174 TO 176 192 TO 194 342 359 TO 361
1143. LZ 3.26 MEMB 1732 1733 1757
1144. LZ 4 MEMB 1728 1735 1736 1758
1145. LZ 4 MEMB 1729 1730 1737 TO 1740 1759 1760
1146. LZ 6.76 MEMB 1731 1741 TO 1744 1746
1147. LZ 3.76 MEMB 396 TO 398
1148. MAIN 0 MEMB 3 4 7 8 11 TO 16 19 21 TO 25 27 29 TO 32 34 72 TO 75
82 TO 92 -
1149. 134 136 138 140 142 144 146 148 150 152 159 TO 180 186 TO 195 201
TO 206 -
STAAD SPACE -- PAGE NO.
23
1150. 211 TO 237 239 241 244 250 252 259 261 TO 263 268 TO 273 275 TO
277 -
1151. 282 TO 284 289 TO 291 296 TO 300 303 304 310 TO 312 317 TO 319
324 TO 328 -
1152. 330 331 333 335 TO 343 345 TO 365 367 TO 369 371 TO 381 386 390
TO 399 405 -
1153. 406 TO 407 409 411 TO 416 418 TO 421 424 425 427 TO 430 432 TO
449 455 456 -
1154. 460 TO 464 473 TO 478 480 TO 530 536 TO 550 556 TO 560 562 TO 585
-
1155. 591 TO 610 612 615 617 TO 619 621 623 625 627 628 630 632 635 637
TO 639 -
1156. 641 643 645 647 648 650 652 655 657 659 661 663 665 667 668 670
678 712 715 -
1157. 717 719 721 723 725 727 728 730 731 808 TO 815 817 819 821 827
832 833 835 -
1158. 836 TO 839 841 843 845 851 TO 853 856 TO 867 869 870 875 880 TO
887 889 891 -
1159. 893 899 904 TO 911 913 915 917 923 928 TO 935 937 939 941 947 952
TO 959 -
1160. 961 963 965 971 976 TO 983 985 987 989 995 1000 1001 1004 1005
1007 1009 -
1161. 1011 1013 1019 1244 1551 1554 1556 1558 1560 1562 1564 1566 1567
1569 1571 -
1162. 1573 1575 1577 1579 1581 1583 1585 1587 1591 1593 1596 1598 TO
1600 1602 -
1163. 1604 1606
1164. MAIN 0 MEMB 1608 1809 1810
1165. MAIN 0 MEMB 1802 TO 1804
1166. MAIN 0 MEMB 1609 1611 1613 1615 TO 1617 1619 1621 1623 1625 1627
1629 1633 -
1167. 1634 TO 1635 1684 1686 1691 1693 1696 TO 1703 1707 TO 1750 1753
1757 TO 1766 -
1168. 1805 1806 1808
1169. MAIN 0 MEMB 1024 TO 1029 1031 1033 1035 1037 1043 TO 1048 1097 TO
1102 1105 -
1170. 1106 TO 1114 1116 TO 1119 1126 TO 1130 1143 1144 1148 TO 1153
1155 TO 1164 -
1171. 1166 TO 1169 1173 1175 TO 1177 1181 TO 1183 1188 TO 1192 1196 TO
1203 1205 -
1172. 1206 TO 1207 1296 1298 1299 1302 1303 1305 1308 1310 1311 1314
1315 1317 1320 -
1173. 1322 1323 1326 1327 1329 1332 1334 1335 1338 1339 1341 1344 1346
1347 1350 -
1174. 1351 1353 1356 1358 1359 1362 1363 1365 1368 1370 1371 1374 1375
1377 1380 -
1175. 1382 1383 1386 1387 1389 1392 1394 1395 1398 1399 1401 1404 1406
1407 1410 -
1176. 1411 1413 1416 1418 1419 1422 1423 1425 1428 1430 1431 1434 1435
1437 1440 -
1177. 1441 TO 1443 1446 1447 1449 1452 TO 1455 1458 1459 1461 1464 TO
1467 1470 -
1178. 1471 1473 1476 1478 1479 1482 1483 1485 1488 1490 1491 1494 1495
1497 1500 -
1179. 1502 1503 1506 1507 1509 1512 TO 1516 1541 1545 1589 1590 1592
1594 1595 -
1180. 1597 1601 1603 1605 1607 1610 1612 1614 1618 1620 1622 1624 1626
1628 1630 -
1181. 1631 TO 1632 1672 TO 1676 1684 1686 1687 1704 TO 1706 1746 1751
1835 TO 1849
1182. MAIN 1 MEMB 732 TO 737 744 TO 755 780 TO 785 792 TO 803 1049 TO
1054 1061 -
1183. 1062 TO 1078 1085 TO 1096 1517 TO 1522 1529 TO 1540 1636 TO 1641
1648 TO 1671 -
1184. 1811 TO 1834
1185. RATIO 1 MEMB 3 4 7 8 11 TO 16 19 21 TO 25 27 29 TO 32 34 72 TO 75
82 TO 92 -
1186. 134 136 138 140 142 144 146 148 150 152 159 TO 180 186 TO 195 201
TO 206 -
1187. 211 TO 237 239 241 244 250 252 259 261 TO 263 268 TO 273 275 TO
277 -
1188. 282 TO 284 289 TO 291 296 TO 300 303 304 310 TO 312 317 TO 319
324 TO 328 -
1189. 330 331 333 335 TO 343 345 TO 365 368 369 371 TO 381 386 390 TO
399 -
1190. 405 TO 407 409 411 TO 416 418 TO 421 424 425 427 TO 430 432 TO
449 455 456 -
1191. 460 TO 464 473 TO 478 480 TO 530 536 TO 550 556 TO 560 562 TO 585
-
1192. 591 TO 610 612 615 617 TO 619 621 623 625 627 628 630 632 635 637
TO 639 -
1193. 641 643 645 647 648 650 652 655 657 659 661 663 665 667 668 670
678 712 715 -
1194. 717 719 721 723 725 727 728 730 731 808 TO 815 817 819 821 827
832 833 835 -
1195. 836 TO 839 841 843 845 851 TO 853 856 TO 867 869 870 875 880 TO
887 889 891 -
1196. 893 899 904 TO 911 913 915 917 923 928 TO 935 937 939 941 947 952
TO 959 -
1197. 961 963 965 971 976 TO 983 985 987 989 995 1000 1001 1004 1005
1007 1009 -
1198. 1011 1013 1019 1551 1554 1556 1558 1560 1562 1564 1566 1567 1569
1571 1573 -
1199. 1575 1577 1579 1581 1583 1585 1587 1591 1593 1596 1598 TO 1600
1602 1604 -
1200. 1606 1608 1609
1201. RATIO 1 MEMB 1611 1809 1810
1202. RATIO 1 MEMB 1802 TO 1804
1203. RATIO 1 MEMB 1613 1615 TO 1617 1619 1621 1623 1625 1627 1629 1633
TO 1635 -
1204. 1691 1693 1698 1699 1702 1703 1707 TO 1744 1748 1750 1753 1757 TO
1766
1205. RATIO 1 MEMB 1024 TO 1029 1031 1033 1035 1037 1043 TO 1048 1097
TO 1102 1105 -
STAAD SPACE -- PAGE NO.
24
1206. 1106 TO 1114 1116 TO 1119 1126 TO 1130 1143 1144 1148 TO 1153
1155 TO 1164 -
1207. 1166 TO 1169 1173 1175 TO 1177 1181 TO 1183 1188 TO 1192 1196 TO
1203 1205 -
1208. 1206 TO 1207 1296 1298 1299 1302 1303 1305 1308 1310 1311 1314
1315 1317 1320 -
1209. 1322 1323 1326 1327 1329 1332 1334 1335 1338 1339 1341 1344 1346
1347 1350 -
1210. 1351 1353 1356 1358 1359 1362 1363 1365 1368 1370 1371 1374 1375
1377 1380 -
1211. 1382 1383 1386 1387 1389 1392 1394 1395 1398 1399 1401 1404 1406
1407 1410 -
1212. 1411 1413 1416 1418 1419 1422 1423 1425 1428 1430 1431 1434 1435
1437 1440 -
1213. 1441 TO 1443 1446 1447 1449 1452 TO 1455 1458 1459 1461 1464 TO
1467 1470 -
1214. 1471 1473 1476 1478 1479 1482 1483 1485 1488 1490 1491 1494 1495
1497 1500 -
1215. 1502 1503 1506 1507 1509 1512 TO 1516 1541 1545 1589 1590 1592
1594 1595 -
1216. 1597 1601 1603 1605 1607 1610 1612 1614 1618 1620 1622 1624 1626
1628 1630 -
1217. 1631 TO 1632 1672 TO 1676 1684 1686 1687 1704 TO 1706 1746 1751
1835 TO 1849
1218. TRACK 2 MEMB 3 4 7 8 11 TO 16 19 21 TO 25 27 29 TO 32 34 72 TO 75
82 TO 92 -
1219. 134 136 138 140 142 144 146 148 150 152 159 TO 180 186 TO 195 201
TO 206 -
1220. 211 TO 237 239 241 244 250 252 259 261 TO 263 268 TO 273 275 TO
277 -
1221. 282 TO 284 289 TO 291 296 TO 300 303 304 310 TO 312 317 TO 319
324 TO 328 -
1222. 330 331 333 335 TO 343 345 TO 365 368 369 371 TO 381 386 390 TO
399 -
1223. 405 TO 407 409 411 TO 416 418 TO 421 424 425 427 TO 430 432 TO
449 455 456 -
1224. 460 TO 464 473 TO 478 480 TO 530 536 TO 550 556 TO 560 562 TO 585
-
1225. 591 TO 610 612 615 617 TO 619 621 623 625 627 628 630 632 635 637
TO 639 -
1226. 641 643 645 647 648 650 652 655 657 659 661 663 665 667 668 670
678 712 715 -
1227. 717 719 721 723 725 727 728 730 TO 737 744 TO 755 780 TO 785 792
TO 803 808 -
1228. 809 TO 815 817 819 821 827 832 833 835 TO 839 841 843 845 851 TO
853 -
1229. 856 TO 867 869 870 875 880 TO 887 889 891 893 899 904 TO 911 913
915 917 -
1230. 923 928 TO 935 937 939 941 947 952 TO 959 961 963 965 971 976 TO
983 985 -
1231. 987 989 995 1000 1001 1004 1005 1007 1009 1011 1013 1019 1024 TO
1029 1031 -
1232. 1033 1035 1037 1043 TO 1054 1061 TO 1078 1085 TO 1102 1105 TO
1114 1116
1233. TRACK 2 MEMB 1802 1809 1810
1234. TRACK 2 MEMB 1803 1804
1235. TRACK 2 MEMB 1117 TO 1119 1126 TO 1130 1143 1144 1148 TO 1153
1155 TO 1164 -
1236. 1166 TO 1169 1173 1175 TO 1177 1181 TO 1183 1188 TO 1192 1196 TO
1203 1205 -
1237. 1206 TO 1207 1272 TO 1291 1296 1298 1299 1302 1303 1305 1308 1310
1311 1314 -
1238. 1315 1317 1320 1322 1323 1326 1327 1329 1332 1334 1335 1338 1339
1341 1344 -
1239. 1346 1347 1350 1351 1353 1356 1358 1359 1362 1363 1365 1368 1370
1371 1374 -
1240. 1375 1377 1380 1382 1383 1386 1387 1389 1392 1394 1395 1398 1399
1401 1404 -
1241. 1406 1407 1410 1411 1413 1416 1418 1419 1422 1423 1425 1428 1430
1431 1434 -
1242. 1435 1437 1440 TO 1443 1446 1447 1449 1452 TO 1455 1458 1459 1461
-
1243. 1464 TO 1467 1470 1471 1473 1476 1478 1479 1482 1483 1485 1488
1490 1491 -
1244. 1494 1495 1497 1500 1502 1503 1506 1507 1509 1512 TO 1522 1529 TO
1541 1545 -
1245. 1551 1554 1556 1558 1560 1562 1564 1566 1567 1569 1571 1573 1575
1577 1579 -
1246. 1581 1583 1585 1587 1589 TO 1635 1672 TO 1676 1684 1686 1687 1691
1693 1698 -
1247. 1699 1702 TO 1744 1746 1748 1750 1751 1753 1757 TO 1766 1835 TO
1849
1248. UNT 0.5 MEMB 72 TO 75 82 TO 92 134 136 138 140 142 144 146 148
150 152 201 -
1249. 202 TO 206 211 TO 237 239 241 244 250 252 327 328 407 411 481 TO
485 -
1250. 491 TO 495 501 TO 505 511 TO 515 521 TO 525 541 TO 550 562 564
566 568 570 -
1251. 573 574 576 TO 579 585 591 TO 594 600 731 1160 TO 1164 1173 1175
1177 1183 -
1252. 1190 1674 1684 1691 1693 1698 1699 1702 1703 1711 TO 1727 1748
1750 1762 -
1253. 1764 1766
1254. STP 2 MEMB 3 4 7 8 11 TO 16 19 21 TO 25 27 29 TO 32 34 72 TO 75
82 TO 92 134 -
1255. 136 138 140 142 144 146 148 150 152 159 TO 180 186 TO 195 201 TO
206 211 -
1256. 212 TO 237 239 241 244 250 252 259 261 TO 263 268 TO 273 275 TO
277 -
1257. 282 TO 284 289 TO 291 296 TO 300 303 304 310 TO 312 317 TO 319
324 TO 328 -
1258. 330 331 333 335 TO 343 345 TO 365 368 369 371 TO 381 386 390 TO
399 407 409 -
1259. 411 412 415 416 418 TO 421 424 425 427 TO 430 432 433 460 TO 464
473 TO 476 -
1260. 481 TO 530 536 TO 550 556 TO 560 562 TO 585 591 TO 600 618 638
678 731 808 -
1261. 809 TO 811 832 833 835 852 853 856 TO 859 864 866 870 880 TO 883
904 TO 907 -
STAAD SPACE -- PAGE NO.
25
1262. 928 TO 931 952 TO 955 976 TO 979 1000 1001 1024 TO 1027 1044 TO
1048 1106 -
1263. 1107 TO 1114 1116 TO 1119 1126 TO 1130 1298 1299 1302 1303 1305
1310 1311 -
1264. 1314 1315 1317 1322 1323 1326 1327 1329 1334 1335 1338 1339 1341
1346 1347 -
1265. 1350 1351 1353 1358 1359 1362 1363 1365 1370 1371 1374 1375 1377
1382 1383 -
1266. 1386 1387 1389 1394 1395 1398 1399 1401 1406 1407 1410 1411 1413
1418 1419 -
1267. 1422 1423 1425 1430 1431 1434 1435 1437 1442 1443 1446 1447 1449
1454 1455 -
1268. 1458 1459 1461 1466 1467 1470 1471 1473 1478 1479 1809 1810
1269. STP 2 MEMB 1802 TO 1804
1270. STP 2 MEMB 1482 1483 1485 1490 1491 1494 1495 1497 1502 1503 1506
1507 1509 -
1271. 1514 TO 1516 1591 1592 1594 1595 1597 1599 1601 1603 1605 1607
1610 1612 -
1272. 1614 1616 1618 1620 1622 1624 1626 1628 1630 1633 TO 1635 1675
1676 1691 -
1273. 1693 1698 1699 1702 1703 1707 TO 1744 1748 1750 1753 1757 TO 1766
1274. STP 2 MEMB 1143 1144 1148 TO 1153 1155 TO 1164 1166 TO 1169 1173
1175 TO 1177 -
1275. 1181 TO 1183 1188 TO 1192 1296 1308 1320 1332 1344 1356 1368 1380
1392 1404 -
1276. 1416 1428 1440 1441 1452 1453 1464 1465 1476 1488 1500 1512 1513
1541 1545 -
1277. 1672 TO 1674 1684 1686 1687 1704 TO 1706 1746 1751 1835 TO 1849
1278. STP 1 MEMB 405 406 413 414 434 TO 449 455 456 477 478 480 601 TO
610 612 615 -
1279. 617 619 621 623 625 627 628 630 632 635 637 639 641 643 645 647
648 650 652 -
1280. 655 657 659 661 663 665 667 668 670 712 715 717 719 721 723 725
727 728 730 -
1281. 732 TO 737 744 TO 755 780 TO 785 792 TO 803 812 TO 815 817 819
821 827 836 -
1282. 837 TO 839 841 843 845 851 860 TO 863 865 867 869 875 884 TO 887
889 891 893 -
1283. 899 908 TO 911 913 915 917 923 932 TO 935 937 939 941 947 956 TO
959 961 -
1284. 963 965 971 980 TO 983 985 987 989 995 1004 1005 1007 1009 1011
1013 1019 -
1285. 1028 1029 1031 1033 1035 1037 1043 1049 TO 1054 1061 TO 1078 1085
TO 1102 -
1286. 1105 1196 TO 1203 1205 TO 1207 1272 TO 1291 1517 TO 1522 1529 TO
1540 1551 -
1287. 1554 1556 1558 1560 1562 1564 1566 1567 1569 1571 1573 1575 1577
1579 1581 -
1288. 1583 1585 1587 1589 1590 1593 1596 1598 1600 1602 1604 1606 1608
1609 1611 -
1289. 1613 1615 1617 1619 1621 1623 1625 1627 1629 1631 1632 1636 TO
1641 1648 -
1290. 1649 TO 1671 1811 TO 1834
1291. LOAD LIST 101 TO 109
1292. CHECK CODE MEMB 3 4 7 8 11 TO 16 19 21 TO 25 27 29 TO 32 34 72 TO
75 -
1293. 82 TO 92 134 136 138 140 142 144 146 148 150 152 159 TO 180 186
TO 195 201 -
1294. 202 TO 206 211 TO 237 239 241 244 250 252 259 261 TO 263 268 TO
273 -
1295. 275 TO 277 282 TO 284 289 TO 291 296 TO 300 303 304 310 TO 312
317 TO 319 -
1296. 324 TO 328 330 331 333 335 TO 343 345 TO 365 367 TO 369 371 TO
381 386 390 -
1297. 391 TO 399 405 TO 407 409 411 TO 416 418 TO 421 424 425 427 TO
430 -
1298. 432 TO 449 455 456 460 TO 464 473 TO 478 480 TO 530 536 TO 550
556 TO 560 -
1299. 562 TO 585 591 TO 600 618 638 678 731 TO 737 744 TO 755 780 TO
785 -
1300. 792 TO 803 808 TO 814 832 833 835 TO 838 852 853 856 TO 862 864
866 870 880 -
1301. 881 TO 886 904 TO 910 928 TO 934 952 TO 958 976 TO 982 1000 1001
1004 1005 -
1302. 1024 TO 1029 1044 TO 1054 1061 TO 1078 1085 TO 1098 1106 TO 1114
-
1303. 1116 TO 1119 1243 1244 1298 1299 1302 1303 1305 1310 1311 1314
1315 1317 -
1304. 1322 1323 1326 1327 1329 1334 1335 1338 1339 1341 1346 1347 1350
1351 1353 -
1305. 1358 1359 1362 1363 1365 1370 1371 1374 1375 1377 1382 1383 1386
1387 1389 -
1306. 1394 1395 1398 1399 1401 1406 1407 1410 1411 1413 1418 1419 1422
1423 1425 -
1307. 1430 1809 TO 1834
STEEL DESIGN