Professional Documents
Culture Documents
Valve Type and Features
Valve Type and Features
The three basic functions of valves are: 1. to stop flow, 2. to keep a constant direction of flow, and 3. to regulate
the flow rate and pressure. To select the correct valve to fulfill these functions properly, an outline of the
different types of valves and their features is given below.
Butterfly valve Check valve Gate valve Globe valve Ball valve
Open Open
Open
Open
Open
Closed
Closed Closed
Closed
Closed
Valve shaped like a For use when flow is only in Like its name implies, the The globe-shaped body Valve stopper is ball-
butterfly. one direction. gate is lowered to cut off controls the fluid into a S- shaped.
Tight shut-off and can be Lightweight disc allows the path of flow. shaped flow. For use as an on/off valve
used as a control valve. vertical installation. For use as an on/off valve Tight shut-off and can be (not suitable as a control
Little resistance to flow High operating speed (not suitable as a control used as a control valve. valve).
(allows smooth flow). prevents water hammer. valve). Large resistance to flow Little resistance to flow
Optimal for automated Little resistance to flow (does not allow smooth when fully open (allows
operation with a low when fully open (allows flow). smooth flow).
operating torque and 90 smooth flow). Much power is required to Optimal for automated
degrees operating angle. Long stroke requires time to open and close the valve operation with a 90 degrees
Lightweight and compact open and close; not suitable (not suitable for large operating angle.
(large diameter models are for quick operation. sizes). Advanced technology is
also available). required to manufacture
ball.
Comparison of butterfly valves with other valves (using 100mm diameter TOMOE 700G model valve)
Butterfly valve and globe valve Butterfly valve and ball valve Butterfly valve and gate valve
Item Butterfly valve Globe valve Item Butterfly valve Ball valve Item Butterfly valve Gate valve
Pressure loss• • • • • • 0.3 1.5 Pressure loss• • • • • • 0.3 0.05 Pressure loss• • • • • • 0.3 0.2
Flow characteristics Equal • • Equal • • Flow characteristics Equal • • Quick open Flow characteristics Equal • • Quick open
Rangeability 10• 1• 30• 1• Rangeability 10• 1• 3• 1•
2
60
ear
Lin
• •Cv • •
1.5
40
•
l•
ua
1 1
Eq
0.7 20
• •• • • • 0.2
0
0 20 40 60 80 100
Butterfly Globe Ball Gate Butterfly Globe Ball Gate
valve valve valve valve valve valve valve valve Valve opening • • • •
Data
Data-01 463
Valve Sizing Procedures
It is essential to understand the valve sizing formula and selection procedure when determining the size of a
valve. The following is the proper selection procedure. The valve sizing calculation is based on ISA.
1. Judge if the flow condition is subcritical or critical based on the given flow condition.
3. Select the size of the valve using the Cv value chart. Consider the following points when sizing the valve.
q A proper adjustment of the Cv calculation should be made based on the piping adjustment coefficient
Fp if a valve is located between reducers.
w If the result of the Cv calculation is over 80% compared to the full Cv value, select a valve one size
larger.
Example: For fresh water with P1 = 0.3 MPa, P2 = 0.25 MPa, flow rate = 100 m3/h, the calculated Cv
will be 164. If 80 mm, 507V is selected, the rated Cv is 176. The calculated Cv (164) is over 80% of
rated the Cv (176) in this case. We recommend 100 mm, 507V.
e If no • •P is given, 5 to 10% of the pump outlet pressure should be used as the assumed • •P for valve
sizing.
Data
464 Data-02
Cv Value Calculation
Cv value calculation
Data
Data-03 465
Symbol Legend
Symbol
Cv: Valve flow coefficient
FL: Pressure recovery coefficient
G: Specific gravity of gas • • • • • • • • • • • • • • • • • • •(Air • •= 1) • • • • • • • • • • • • • • •
Gf: Specific gravity at valve-inlet temperature• • • • • • • • • •••••••••••••••
(Water = 1 at 15 degrees C)
P1: Valve-inlet pressure• • • • • • • • • • • • • • • • • • • •••••••••••••••••••••••
(kPaA)
P2: Valve-outlet pressure• • • • • • • • • • • • • • • • • • ••••••••••••••••••••••
(kPaA)
• •P: Pressure difference across valve [P1 — P2] • • • • • • • • • •••••••••••
(kPa)
Pc: Critical pressure • • • • • • • • • • • • • • • • • • • • ••••••••••••••••••••••
(kPaA)
Pv: Saturated vapour pressure of liquid at valve-inlet temperature (kPaA)
• •PS: Max. DP for sizing
• Working conditions: Outlet pressure is higher than vapour pressure.
• • • •• •P•S •= P1 — Pv • •••••
(kPa)
• Working conditions: Outlet pressure is equal to or lower than vapour pressure.
Pv
• • •= P1 —• 0.96•
• • • DPS • • • •0.28
• • • • • •Pv•
• • • • • • • • • • • • • • • • • • ••••••••••••••••••••
(kPa)
PC
(m3 / h)
q: Volume flow rate of liquid• • • • • • • • • • • • • • • • • •••••••••••••••••••••••
Q: Volume flow rate of gas [At 15 degrees C, 1 atm]• • • • • • • • (m• •3 / •h)• • • • •
288
• •= Nm3/h• •
273
T: Fluid temperature [273 + degrees C]• • • • • • • • • • • • • (K)
• • • • • • • • • • •
Tsh: Degree of superheat • • • • • • • • • • • • • • • • • • • •••••••••••••••••••••
(degrees C)
• • =• T• — Tc
Tc: Saturated vapour temperature at valve-inlet pressure (K)
W: Mass flow rate (T / h) = (1,000 kg / h)
CvR = Fp Cv
Data
466 Data-04
Conversion Formula for Reference
Pressure loss coefficient Cv value Length of pipe
• •••
: Pressure loss coefficient
• •P: Pressure difference (kPa)
: Acceleration of gravity 9.8 m/sec2
: Specific gravity (water = 1000) (kg/m3)
V: Flow velocity (m/sec)
Data
Data-05 467
Guidance for Vacuum Use
Nominal dia. Usable vacuum (kPaA) Valve seat leak
Valve type range Remark
(mm) 10 to 50 degrees C 50 to 80 degrees C 80 to 100 degrees C (kPa• R/h)
•
••
302A 250-300 1.33 3.99 5.32 14.0
350-600 2.66 3.99 5.32
Special gland structure required.
40-200 1.33 1.33 2.66 14.0
302Y
250-300 2.66 3.99 5.32
50-200 1.33 1.33 2.66 14.0
337Y
250-300 2.66 3.99 5.32
40-200 1.33 1.33 2.66 1.0
304Y
250-300 2.66 3.99 5.32 8.0
846T 65-200 Leakage increases if heat cycle
0.133 1.33 2.66 0.3
847T 50-300 and open/close frequency is high.
731X
350-600 2.66 13.3 Use not possible. 5.0
732X
Data
468 Data-06
Velocity Calculation
Velocity limitation
For liquids
For steam
Where:
V: Flow velocity (m/sec)
Q: Flow rate
Liquid (m3/h)
Gas [At 15 degrees C, 101325 Pa] (m3/h)
= Nm3/h
Steam (kg/h)
U: Specific volume of valve-outlet (m3/kg)
D: Nominal size (mm)
P2: Valve-outlet pressure (kPaA)
T: Temperature (degrees C)
Data
Data-07 469
Noise Prediction Methods and Countermeasures
Noise measuring method
Fig. 1 Laboratory test unit by ISA-RP59.1 Fig. 2 Position of microphone in plant by ISA-RP59.2
Data
470 Data-08
Noise calculation formula for valves other than 507V and 508V Types
For gases
Where:
SP: Noise value [sound pressure level at 91cm] (dBA)
Cv: Flow coefficient in actual conditions
FL: Pressure recovery coefficient
P1: Valve upstream pressure (kPaA)
P2: Valve downstream pressure (kPaA)
m: Weight of pipe wall (kg/m2)
• : • Apparent valve orifice coefficient (butterfly valve: n = 1.4)
TL: Transmission loss • •Except for valves releasing directly into the air.
Note: When the difference between Kc and FL2 exceeds 10% of Kc, substitute Kc for FL2.
Data
Data-09 471
Specific gravity SG Specific gravity SG
• 2
•
Saturated steam • 1
•
Superheated steam
Natural gas 0
Hydrogen • 1•
Oxygen
• 2
• •kg/m2• •
• • ••••
t: Pipe thickness (mm)
Nominal dia. m
mm inch SGP Sch20 Sch40 Sch60 Sch80 Sch10S Sch20S
40 1 1• 2• 27.5 • ••• 29.0 35.3 40.0 22.2 23.8
50 2 29.8 25.1 30.6 38.5 43.2 22.2 27.8
65 2 1• 2• 33.0 35.3 40.8 47.1 55.0 23.8 27.8
80 3 33.0 35.3 43.2 51.8 59.7 23.8 31.7
100 4 35.3 38.5 47.1 55.7 67.5 23.8 31.7
125 5 35.3 40.0 51.8 63.6 74.6 27.0 39.7
150 6 39.3 43.2 55.7 73.0 86.4 27.0 39.7
200 8 45.5 50.2 64.4 80.9 99.7 31.7 51.5
250 10 51.8 50.2 73.0 99.7 118.5 31.7 51.5
300 12 54.2 50.2 80.9 112.3 136.6 35.7 51.5
350 14 62.0 62.0 87.1 118.5 149.2 • ••••••••••••••
• ••••••••••••••
400 16 62.0 62.0 99.7 131.1 168.0 • •••••••••••••• • ••••••••••••••
450 18 62.0 62.0 112.3 149.2 186.8 • •••••••••••••• • ••••••••••••••
500 22 62.0 74.6 118.5 161.7 205.7 • •••••••••••••• • ••••••••••••••
550 20 • • 74.6 124.8 174.3 224.5 • •••••••••••••• • ••••••••••••••
600 24 • ••• 74.6 137.4 193.1 243.4 • •••••••••••••• • ••••••••••••••
Data
472 Data-10
• •......Acoustical efficiency factor
Data
Data-11 473
Valve noise reduction countermeasures
1 Noise source
2 Sound insulation
When selecting a countermeasure, controllability of process, initial cost and maintenance cost should be
considered along with noise evaluation and noise type.
Various factors should be discussed between the customer and manufacturer. Please refer to the section
Calculation of Estimated Cavitation and its countermeasure to reduce and prevent cavitation noise.
w Soundproof lagging
• •••••
In this countermeasure, piping is covered with layers of • •
• •••••
heat insulating materials (rock wool), lead plates, or iron
• •••••
plates, etc.
474 Data-12
Calculation of Estimated Cavitation
Cavitation generation in butterfly valves
Cavitation is caused by low pressure areas in fluids. There are four causes of low pressure areas:
The main causes of cavitation generation in butterfly valves are (1) and (2).
Thus, when the valve is nearly closed, the flow passes over the upper and lower edges of the disc as shown in
figure. 1. The low pressure area can be caused when high flow velocity is created.
VC (vena contracta)
Figure 2 shows orifice flow corresponding to valve flow. The contracted part is called vena contracta. The
relation between pressure and flow rate is shown in figure 3.
VC
P1
When fluids flow at high velocity and pressure drops below
the saturated vapour pressure, air bubbles are produced.
They are carried away toward the valve downstream side,
Pressure (P)
Flow (V)
P2
and then, as surrounding water recovers its original
pressure, air bubbles break instantaneously (approx. 1/1000
Pv
sec) and produce a strong impact force (200 to 500 atm). If
air bubbles break near a substance, the impact applies
great stress on both the outside and inside of the Pvc
Data
Data-13 475
Cavitation generation process in butterfly valves and formula to estimate it
P2
Pv
Pvc Normal flow means turbulent flow.
In this stage, valve flow rate increases
in proportion to the square root of the
differential pressure.
476 Data-14
Cavitation prediction
No cavitation Flashing
• •P < Kc (P1 — Pv) P2 < Pv
FL2 (P1• •Pv) > • •P
Incipient cavitation
• •P: Pressure difference across valve [P1• •P2] (kPa)
• •P = Kc (P1 — Pv) Kc: Cavitation coefficient
P1: Valve-inlet pressure (kPaA)
Critical cavitation P2: Valve-outlet pressure (kPaA)
Pv: Vapour pressure of liquid (kPaA)
FL2 (P1 — Pv) > DP > Kc (P1 — Pv) FL: Pressure recovery coefficient
Full cavitation
• •P • •FL2 (P1 — Pv)
Cavitation level and availability
No cavitation
Suitable
Incipient cavitation Consult us regarding
usage.
Unsuitable
Critical cavitation
Note:
Full cavitation (Countermeasure is necessary) Normal operation
material is stainless steel
Flashing except when. critical
(Countermeasure is necessary)
cavitation is determined.
The following are the main methods for reducing or preventing cavitation damage to control valves.
(1) Install valves in series and control them. This method is for reducing the pressure load on each valve.
In this case, space valves out at least 4D (4 times the pipe diameter). The total Kc or FL will be improved. In
order to avoid full cavitation FL should satisfy the following condition:
• • • • • • •FL• >• • • •
• •••••
In this case, however, valve control balance may be difficult.
Example:
When 507V and 508V types are nearly fully opened, FL is 0.72. When 507V and 508V types are installed in series,
the combined FL is 0.72 = 0.84 and the permissible pressure difference across the valve is increased by 36%.
However, both valves should be operated under exactly the same conditions.
(2) Use a resistance plate (perforated orifice for pressure reduction) at the same time. If the flow rate fluctuates
heavily, a good result cannot be expected.
(3) Use a valve with higher Kc or FL .
(4) Lower the installation position of the valve; that is, lower the secondary pressure.
However, this method is hard to adopt in existing piping installations.
Data (5) Rectify the turbulent flow by using a rectifier grid.
Data-15 477
Cavitation coefficient Kc and pressure recovery coefficient FL
1.0 1.0
0.9 0.9
0.8 0.8
0.7 0.7
0.6 0.6
Kc 0.5 FL 0.5
0.4 0.4
0.3 0.3
0.2 0.2
0.1 0.1
0 10 20 30 40 50 60 70 80 90 100 0 10 20 30 40 50 60 70 80 90 100
(Fully closed) Valve opening (%) (Fully open) (Fully closed) Valve opening (%) (Fully open)
0.9 0.9
0.8 0.8
0.7 0.7
0.6 0.6
Kc 0.5 FL 0.5
0.4 0.4
0.3 0.3
0.2 0.2
0.1 0.1
0 10 20 30 40 50 60 70 80 90 100 0 10 20 30 40 50 60 70 80 90 100
(Fully closed) Valve opening (%) (Fully open) (Fully closed) Valve opening (%) (Fully open)
1.0 1.0
0.9 0.9
0.8 0.8
0.7 0.7
0.6 0.6
Kc 0.5 FL 0.5
0.4 0.4
0.3 0.3
0.2 0.2
0.1 0.1
0 10 20 30 40 50 60 70 80 90 100 0 10 20 30 40 50 60 70 80 90 100
(Fully closed) Valve opening (%) (Fully open) (Fully closed) Valve opening (%) (Fully open)
Data
478 Data-16
Face to Face Dimensions
• • • •
(80mm to 300mm) 304A
302Y• 304Y 700E (discontinued) (discontinued) 338Y
(350mm to
•
508V (discontinued)
600mm)
types
846T• 847T
•
773Z• 778Z
•
700G• 704G
• • 705G
•
731P• 732P
• • •
732X• 731X
•
702Z (discontinued)
Remark: For detalied dimensions, please refer to the individual dimensional drawings.
Data
Data-17 479
Unit Conversion
Cavitation prediction Pressure unit conversion Temp. conversion table
Conversion from pressure unit for
Conversion from flow rate unit for each type to K/h each type to MPaA Temperature conversion
••
• •••
• • • •• ••••••••
• • • • • • •• • • • • • • • ••••
•• • • ••• •• ••• • ••• • • • •
• ••••
•
•• ••
• • ••• • • ••• • • • • • • ••• • • • • ••••••• ••••• •••••• •• • •• • •• • ••• • • • •• • •• •••••• •••••• • • • ••••••••• • •••
Gas m3/h • Å • • • • • • ••• ••••• • • • ••••••••• •• • •••• • • • • • •••••
• •••
• •
•• • • • ••••••• ••••••••••• ••
Gas m3/h •••• • • ••••••• •••••••••••
• •••
• • • • • • •••• • •
• ı• • • • • • • • •••• • • •••• •••••• • •• • • • •
(at 15• • 101kPa• • •• • • •• • • • • • •• •••••• •••••• • • • ••••••••• • • • •• ••••••• • • •••• • • •• •••••
• • • •• ••• ••• ••• • • • •••••••••••
• •••
kg/h • • • •• • ••• • • ••••••• • • • •• • • • • •••••••••• • • • •• ••• ••• ••• • • • •••••••••••• • •• • • • • • • ••• •••••• • • • ••••••••• • • • •• ••••••• • • •••• • • •• •••••
kR/h •• • • •
• Å
• • ••
• •••
• • •• ••• •• ••• • • •••••••••• • • •• • • • • • • ••• •••••• • • • ••••••••• • • • •• ••••••• • • •••• • • •• ••••••
• •••
t/h • • • •••• • • • • • • • • •• • • • • •••••••••••••••• • • N••
• • •••• • •••••••••••• • • •• • • • • • • •••• • • • • • • • ••• • • •• ••••••
• • • •• ••••••• •••••
R/h • • •• • • • Å••
• •••
• • •• • • ••••••• • • • • • • • • • N••
••• • • •• • • • • • • •••• • • • • • • • • • •• •••••• • ••• • • •• ••••••
R/min. • • •• • •••••• • • •• • • Å••
• • • • • • •• ••••• • • •• • • • • • •• ••••••• • • • • • • • • • •• •••••• • ••• • • •• ••••••
• •••
t/min. • • • • • • •••••• • N
• •••
• • • • • • •• • • • • •• • • • • ••••••••••••••• • • •• • • • • • • ••• •••••• • • • ••••••••• • • • •• •••••• • • •••• • • •• ••••••
Lb/h • • •• • • • • • • • • •• • • ••••••••••••••••• • ••
• • •• • • • • • • •• • • • • ••••••••••••••••• • •••••• • • • • • •• •••••• ••••• • • • ••••••••• • ••• •• ••••••• • • •••• • • •• ••••••
3
• •• • • • • • Å••
• •••
CFH••••
ft /h) • • •• • • • • ••••••••• • • • • • • • • • • • • • • ••••••• • • • • • • ••• ••••• • • • ••••••••• • ••• •• ••••••• • • •••• • • •• ••••••
SCFH (Nft3/h) • • •• • • • • • ı••
• • • • • • • •• • •• • • • • ••••••••• • • • • • •••••••
• •••
• • • • • • •••• • • • ••• •• ••••••• • • •••• • • •• ••••••
BBL/h (barrel) • • •• • • ••••••• • • •• • • • Å••
• • • • • • • • • • • ••••••• • • •• • • • ••••••••• • ••• •• ••••••• • • •••• • • •• ••••••
BBL/min. • • •• • • • • • •••••••••• • • •• • • • • • • Å••• • • • • • • • • •• • • ••••••• • • • • •••••• •••••••••••• • •• ••••• • • •••• • • •• ••••••
• •• • • • • Å••
••
GPM (gallon/min.) • • •• • • • •••••••• • • • • • • • • • • • ••• • • • ••• •• • • •• • •• •••••• •••••• • • • •••••••••
• • ••• ••• ••• • ••• •••• • •• ••••• • • •••• • • • •• •••••••
CFM (ft3/min.) • • •• • • ••••••• • • •• • • • Å• • • • • •
••
• • ••• ••• ••• • ••• ••••
• •••
• • • ••• •• •••• • • • • • • •••• • • • • • • • •• ••••• • • •••• • • • •• •••••••
SCFM • • •• • • • ı••
• • • • • • • • •• • • ••••••• •• •• N
••••
• •••
• • •• • • • • • • • • • • • • • • • • •• •••••• • • •••• • • • •• •••••••
Nm3/h
• • •• •• • • •• • • • • • • • ••••• • • • • • ••• •• • • • • • • • • • • • • • • • • •• •••••• • • •••• • • • •• •••••••
(at 0• • 101kPa)
• • •• •••••• • • •••• • • • •• •••••••
Å• • •••• • • • • • • • ••••• ••• ••• • •• • • • • • • ••• •• • •••
•• • •• • ••••• •• ••• •• • • • ••• • • ••• •• •• • •• • •• ••• ••• • • • • • • • • • •• •••••• • • •••• • • • •• •••••••
ı• • •••• • ••••• • • • • • • ••••• • • • • •• ••• • ••• •• •• •••••• • • • •• •• ••• • • • • •••• • •• • • • • • •• •••••• • • •••• • • • •• •••••••
• • •• •• • • • •••• •• •• • ••• ••••••••••••••••
• • • • • • • • • • • • • • •• • • • •••••••• •• ••• • •• • •••••••••••••••••••••••••••••••••••• • • •• •••••• • • •••• • • • •• •••••••
• • •• •••••• • • •••• • • • •• •••••••
• • •• •••••• • • •••• • • • •• •••••••
Pressure conversion table
• • •• •••••• • • •••• • • • •• •••••••
• ••• •• • • •• • • •••••••••• O••• • ••• • • • • •• • • •• •• •• • • • • • • • • • • • ••• •• •• • • • • • •• •••••• • • •••• • • • •• •••••••
• •••••••••••••••••••••• • • • •• ••••••••• • • • • • ••• ••• •• • • • • • • ••• ••• •• • • •• • • • • ••• •••
•• • • ••• •••• • • ••• ••• • •••• • • ••• ••••
•• • • •• • • •••••• • • • ••• •••
•• •• •••••• • • • • ••• •• • • • • • •• • •• •••••• • • • •••••
•• • • • •• •••••••
•• • • • •••••• • • • • ••••••••••••••••••••••• •• • • • • • • ••• •••
• • • • ••• ••• •• • • •• • • • • ••• •••
•• • • •• •• • •• ••• •• •• • • ••• ••••
• •••• • • ••• ••• •• •• •••••• • • • • ••• ••
• • • •• ••• • • • ••• ••• • • • • • •• • •• •••••• • • • •••••
•• • • • •• •••••••
• • • • •• •••• • • • • • • •• •••••••
•••• • • ••••••••••••••••••••• • • • • •••••••• •• • • • • ••••••••••••• • •• • • • • •• •••••••
• •• • •••••••••••••••••••••••• • •• • • • • •••••••• • • • • ••• •• •••••• • • • •••••
• • •••••• •••••••••••••••••••••••• • • • •• •••••••
•• •••••• •• • • • •••••••••••••• • •• •••••• • • • ••••• • • • •• •••••••
•• • •
• • • • •• •••• • • • • • • •• ••••••
•••• • • • • • ••• ••• •• • • • ••••••••••••••••••••• • •• • • • • • ••
• •• • •••••••••••••••••••••••• • • • •• • •• • • • • ••• •••
• •••• • • •••••••••••••
••
• •• • • • • •••• •••••• • •• • • ••••••••••••••• •• ••••
• •• • • • • • • • • ••••••• • • • •• •• • •
• • • • • ••••••••••••••••••••
•• • •• • • • • • •• •• • •
• • • • •• •• • • ••••••• • • • • •• • • • • •• • •••••• •• • • • •••••••••••••• • •• •••••• • • • •••••
•• • • • • • •• •••••••
• •• • • • • •• •••• •••••• • • • • •• ••••••
•••• • ••••••• • • ••• ••• •• • • ••
• •••••••••••••••••••••••••••
• •• • •••••••••••••••••••••••• • •• • • • • •••••••••••••
• ••••••••••••••••••••• • •• • • • ••• ••••• •••••• •• • • • •••••••••••••• • •• •••••• • • • ••••• • • • •• •••••••
• •• • • • • •• •••• •••••• • ••••••••••••••••••••••••••• •• • • ••••••• • • ••• •••
• •• • • • • ••• ••• •• • • • •• • • • ••• •••
•• • •• •• • • • • ••• ••• • •• • • • • ••• •••
•• • • • •••••••••••••••••••••••• • • •• •••••• • • • •••••
•• •••••• • ••••••••••••••••••••••••• • • • •• •••••••
• •• • • • • •• •••• •••••• • •• • • •• •••••••
• • ••••••• • • ••• •••
•• • • ••
• ••••••••••••••••••••••••••• • •• • ••••••••••••••••••••••••
• •• ••••••••••••••••••••••• • •• • • • • ••••••••••••••• • •• • • • • •••••••••••••• • •• •••••• • • • •••••
• ••••••••••••••••••••• • • • •• •••••••
• •• • • • • •• • • •••••• • ••••••••••••••••••••••••• • •• • • ••• ••• • •• ••• •• • • • ••• ••••• • •• ••• •• • • • ••• ••• • • • • ••••••••••••••••••••• • •• •••••• • • • •••••
• •• • • • • ••• ••• • • ••••••• • • ••• ••• •••••• •• • • • ••• ••• • • • •• • • • •• •••••••
• • •• •••••• • • • ••••• • • • •• •••••••
• • •• •••••• • • • ••••• • • • •• •••••••
• • •• •••••• • • • ••••• • • • •• •••••••
Torque conversion table Specific gravity conversion • • • •• •••••••• • • ••••• • • • •• •••••••
• • • •• •••••••• • • ••••• • • • •• •••••••
• ••• ••
•• • • • ••• ••
•• • • • ••• ••••
•• O• ••• • • O• •• • • •• ••• • • • •• •• • • • • • •••• • • • ••• •••••••
• • ••• ••••••
• • •• • • • • • ••••• ••• • •••••••
• • • • • •••• ••••• • • • •• •••••••
• •• • •• • • • •••• • • • ••
• • • ••••••• • •• • • ••••••• • •• • • • ••••••••• •• • • ••••••• • •• • • ••••••• • •••• •• • • •• • • •• ••••••••••••• • • • •• •••••••• • • ••••• • • • •• •••••••
O•• • • • • • • •• • • •••••••
• • •••• • •• • •• • • •••• • • •• •• • • ••••••• • •• • • • ••••••••• • •• •••••• • •• • • ••••••• • • • • • • • • •••••••••••• • • • •• •••••••• • • ••••• • • • •• •••••••
• • • ••••• • • •••• • •• • • •• • ••••••• • •• • • ••••••• • • • •• ••••••• • •• • • ••••••• • • •• • • •• • • •• •••••••••••••• • • • •• •••••••• • • ••••• • • • •• •••••••
O•• ••• • • • •• • • • • • • •
• • •• • ••••••• • •• • • ••••••• • •• • • ••••••• • •• • •• • •••• • • • •• • • ••••••• • •• • • ••••••• • • • • • • • • •••••••••• • • • •• •••••••• • • ••••• • • • •• •••••••
• • • • •••••• • • •• •••••• • •• • • ••••••• • • • ••••• • •• • • • •• ••••••• • •• • • ••••••• • • • •• •••••••• • • ••••• • • • •• •••••••
• • •• • ••••••• • •• • • ••••••• • •• • • ••••••• • •• • • ••••••• • •• • • ••••••• • •• • •• • •••••• • • • •• •••••••• • • •••••• • • • •• ••••••••
• • • •• • • • • •• •• • • • • • • • • •• • • • • • • •• • •• • • • • • •• •• • • • • • • • • • • • • • •• • • • •• • • • •• •• • • • •• • • • •• • • • • • •
Data
480 Data-18
Physical Properties
Physical properties of liquids
Data
Data-19 481
Physical properties of liquids
482 Data-20
Density of fluids
Data
Data-21
483
Critical pressures and temperatures
Data-22
484
Physical properties of gases
Data-23 485
Physical properties of gases
* Density at 20•C.•
Data
486 Data-24
Physical properties of water
Data-25 487
Saturated steam (Based on temperature) Saturated steam (Based on pressure)
488 Data-26
Flange Standards
Nominal pressure 5K steel flange reference dimensions (JIS B2238-1996)
Data
Data-27 489
Nominal pressure 16K steel flange reference dimensions (JIS B2238-1996)
Data
490 Data-28
Nominal pressure 30K steel flange reference dimensions (JIS B2238-1996)
Data-29 491