Professional Documents
Culture Documents
IC-GM651 1a PDF
IC-GM651 1a PDF
IC-GM651 1a PDF
iGM651
Ver. 1.004
Thank you for choosing this Icom product.
This product is designed and built with Icom’s state of the art
EXPLICIT DEFINITIONS
technology and craftsmanship. With proper care, this product
should provide you with years of trouble-free operation. WORD DEFINITION
Personal injury, fire hazard or electric
RWARNING!
shock may occur.
IMPORTANT CAUTION Equipment damage may occur.
If disregarded, inconvenience only. No risk
NOTE
READ ALL INSTRUCTIONS carefully and completely of personal injury, fire or electric shock.
before using the transceiver.
ii
IN CASE OF EMERGENCY INSTALLATION NOTE
If your vessel requires assistance, contact other vessels and The installation of this equipment should be made in such a
the Coast Guard by sending a Distress call on Channel 16. manner as to respect the EC recommended electromagnetic
USING CHANNEL 16 field exposure limits (1999/519/EC).
DISTRESS CALL PROCEDURE
The maximum RF power available from this device is 25
1. “MAYDAY MAYDAY MAYDAY.”
watts. The antenna should be installed as high as possible
2. “THIS IS ...............” (name of vessel).
for maximum efficiency and that this installation height
3. Say your call sign or other indication of the vessel (AND
should be at least 5 meters above ground (or accessible)
9-digit DSC ID if you have one).
level. In the case where an antenna cannot be installed at
4. “LOCATED AT ...............” (your position).
a reasonable height, then the transmitter should neither be
5. State the nature of the distress and assistance required.
continuously operated for long periods if any person is within
6. G ive any other information which might facilitate the
5 meters of the antenna, nor operated at all if any person is
rescue.
touching the antenna.
Or, transmit your Distress call using digital selective calling In all cases any possible risk depends on the transmitter
on Channel 70. being activated for long periods. (actual recommendation
USING DIGITAL SELECTIVE CALLING (Ch 70) limits are specified as an average of 6 minutes) Normally the
DISTRESS CALL PROCEDURE transmitter is not active for long periods of time. Some radio
1. W h i l e l i f t i n g u p t h e key c ove r, p u s h a n d h o l d licenses will require that a timer circuit automatically cuts the
[DISTRESS] for 3 sec. until you hear 3 short beeps transmitter after 1–2 minutes etc.
change to one long beep.
2. Wait for an acknowledgment on Channel 70 from a Similarly some types of transmitter, SSB, CW, AM, etc. have
coast station. a lower ‘average’ output power and the perceived risk is even
• After the acknowledgement is received, Channel 16 is auto- lower.
matically selected.
3. P ush and hold [PTT], then transmit the appropriate
information as listed above.
iii
FIRMWARE VERSION NUMBER DISPOSAL
The firmware version number is displayed in the opening screen The crossed-out wheeled-bin symbol on your
as below. product, literature, or packaging reminds you
The version number is also displayed when MMSI code check that in the European Union, all electrical and
screen is selected. (see p. 18) electronic products, batteries, and accumula-
Firmware version number indication tors (rechargeable batteries) must be taken to
(This illustration describes ‘Version 1.000’.) designated collection locations at the end of
their working life. Do not dispose of these products as un-
sorted municipal waste. Dispose of them according to the
IC-GM651 laws in your area.
<MMSI>
123456789
Ver1.000
iv
TABLE OF CONTENTS
IMPORTANT....................................................................................... i 4 DUALWATCH/TRI-WATCH........................................................14
EXPLICIT DEFINITIONS.................................................................... i n Description..............................................................................14
PRECAUTIONS................................................................................. ii n Operation................................................................................14
IN CASE OF EMERGENCY............................................................. iii
5 SCAN OPERATION.............................................................15–17
INSTALLATION NOTE...................................................................... iii
n Scan types..............................................................................15
FIRMWARE VERSION NUMBER..................................................... iv
n Setting TAG channels.............................................................16
DISPOSAL........................................................................................ iv
n Starting a scan........................................................................16
1 OPERATING RULES...................................................................1
6 DSC OPERATION..............................................................18–105
D PRIORITIES.............................................................................1
n MMSI code programming.......................................................18
D PRIVACY..................................................................................1
n DSC address ID......................................................................19
D RADIO LICENSES...................................................................1
D Programming Individual ID.................................................19
2 PANEL DESCRIPTION............................................................2–6 D Deleting Individual ID..........................................................22
n Panel description......................................................................2 D Programming Group ID.......................................................23
n Function display........................................................................5 D Deleting Group ID...............................................................26
n Position and Time programming.............................................27
3 BASIC OPERATION..............................................................7–13
n Position and Time indication...................................................30
n Channel selection.....................................................................7
n GPS information indication.....................................................31
D Channel 16...........................................................................7
n Distress call............................................................................32
D Call channel..........................................................................7
D Simple call..........................................................................32
D International channels (Depends on version).......................8
D Regular call.........................................................................34
n Receiving and transmitting.......................................................8
D Transmitting a Distress Cancel...........................................38
n Call channel programming......................................................10
D Transmitting a Distress Acknowledgement call...................39
n Channel comments.................................................................11
D Transmitting a Distress Relay call.......................................41
n Microphone lock function........................................................12
D Transmitting a Distress Relay Acknowledgement call.........48
n Printer function.......................................................................12
n Backlight function....................................................................13
n AquaQuake water draining function........................................13
v
n Transmitting DSC calls............................................................50 n Received messages...............................................................92
D Transmitting an All Ships call..............................................50 D Distress message...............................................................92
D Transmitting an Individual call.............................................52 D Other messages.................................................................95
D Transmitting an Individual Acknowledgement call...............54 n DSC Set mode........................................................................99
D Transmitting a Group call....................................................60 D Printing out the DSC memory contents..............................99
D Transmitting a Position Request call...................................62 D Position Automatic Acknowledgement..............................100
D Transmitting a Position Reply call.......................................64 D DSC Data Output..............................................................101
D Transmitting a Polling Reply call.........................................67 D Squelch Level Setting for Channel 70 Receiver...............102
D Transmitting a Medical Transports call................................69 D Medical Transports item Appearance in DSC Set up menu....103
D Transmitting a Neutral Ship call..........................................70 D Neutral Ship Call item Appearance in DSC Set up menu....104
D Transmitting a Test call........................................................72 D Self Check Testing............................................................105
D Transmitting a Test Acknowledgement call.........................74
7 SET MODE.......................................................................106–108
n Receiving DSC calls...............................................................75
n Set mode programming........................................................106
D Receiving a Distress call....................................................75
n Set mode items.....................................................................107
D Receiving a Distress Acknowledgement call......................77
D Scan type..........................................................................107
D Receiving a Distress Cancel...............................................78
D Scan resume timer...........................................................107
D Receiving a Distress Relay call..........................................79
D Beep tone.........................................................................107
D Receiving a Distress Relay Acknowledgement call............80
D Internal speaker................................................................107
D Receiving an All Ships call.................................................81
D Display contrast................................................................108
D Receiving an Individual call................................................82
D Microphone type...............................................................108
D Receiving an Individual Acknowledgement call..................83
D Cursor (Downward) movement....................................108
➔
D Receiving a Group call.......................................................86
D Receiving a Position Request call......................................87
D Receiving a Position Reply call...........................................88
D Receiving a Polling Request call........................................89
D Receiving a Test call...........................................................90
D Receiving a Test Acknowledgement call.............................91
vi
TABLE OF CONTENTS (Continued)
8 CONNECTIONS AND MAINTENANCE..........................109–117
n Connections..........................................................................109
n Antenna................................................................................110
n Fuse replacement.................................................................110
n Supplied accessories............................................................111
D Accessory connectors set up............................................111
n Power supply connections....................................................112
D Connecting to the DC power supply through the PS-250....112
D Connecting to the AC outlet through the PS-250
and optional PS-240.........................................................113
n Mounting the transceiver......................................................114
D Using the supplied mounting bracket................................114
n MB-75 installation.................................................................115
n Microphone (HM-126RB)......................................................116
D Connection.......................................................................116
n Handset (HS-98)...................................................................117
D Connection.......................................................................117
9 TROUBLESHOOTING.............................................................118
10 SPECIFICATIONS AND OPTIONS..................................119–120
n Specifications.......................................................................119
D General.............................................................................119
D Transmitter........................................................................119
D Receiver............................................................................119
D Dimensions.......................................................................120
n Options.................................................................................120
11 CHANNEL LIST.......................................................................121
vii
OPERATING RULES 1
D PRIORITIES (2) OPERATOR’S LICENSE 1
• Read all rules and regulations pertaining to priorities and A Restricted Radiotelephone Operator Permit is the license
keep an up-to-date copy handy. Safety and Distress calls most often held by small vessel radio operators when a radio 2
take priority over all others. is not required for safety purposes.
3
• You must monitor Channel 16 when you are not operating The Restricted Radiotelephone Operator Permit must be 4
on another channel. posted or kept with the operator. Only a licensed radio op-
erator may operate a transceiver.
5
• False or fraudulent distress signals are prohibited and pun- 6
ishable by law. However, non-licensed individuals may talk over a trans-
ceiver if a licensed operator starts, supervises, ends the call 7
D PRIVACY and makes the necessary log entries. 8
• Information overheard but not intended for you cannot law-
fully be used in any way. Keep a copy of the current government rules and regulations 9
handy. 10
• Indecent or profane language is prohibited.
11
D RADIO LICENSES 12
(1) SHIP STATION LICENSE
You must have a current radio station license before using 13
the transceiver. It is unlawful to operate a ship station which 14
is not licensed.
15
Inquire through your dealer or the appropriate government 16
agency for a Ship-Radiotelephone license application. This
government-issued license states the call sign which is your
craft’s identification for radio purposes.
1
2 PANEL DESCRIPTION
n Panel description
Function display (p. 5) !1 SELECTOR !2 CHANNEL 16/
DIAL CALL CHANNEL KEY
VHF MARINE iGM651
Speaker !3 KEYPAD
!0 TRANSMIT
POWER KEY
o VOLUME CONTROL C
MMSI
q CLEAR KEY
MIC
H/L DIAL 16 w FUNCTION KEY
VOL SQL
i MIC CONNECTOR e DISTRESS KEY
1
2
t POWER KEY [POWER] (p. 8) o VOLUME CONTROL [VOL] (p. 8)
➥ Push to turn power ON and OFF. Rotate to adjust the audio level. 3
• The transceiver does not turn power ON when the connected
PC-250 dc-dc power supply is turned OFF. !0 TRANSMIT POWER KEY [H/L] 4
➥ Push to toggle the output power high or low. (p. 8)
• After turning power ON, the 9-digit MMSI code appears for 2
• Some channels are set to low power only.
5
sec., if programmed.
• When no MMSI code is programmed, “NO MMSI” is dis- ➥ While pushing and holding this key, some keys perform 6
played at power ON, and then the MMSI code programming secondary functions.
is required. 7
➥ While pushing and holding [H/L], turn power ON to ac- !1 SELECTOR DIAL [SELECTOR] (pgs. 7, 8, 106)
Rotate to select the operating channels, set mode con- 8
tivate the AquaQuake function. (p. 13)
tents, etc. 9
➥ While pushing and holding [⁄6 •C], turn power ON to
enter Set mode. (p. 106) !2 CHANNEL 16/CALL CHANNEL KEY [⁄6•C] 10
➥ Push to select Channel 16. (p. 7)
y DIAL KEY [DIAL]
➥ Push to select to the regular channel. (pgs. 7, 8)
➥ Push and hold for 1 sec. to select call channel. (p. 7) 11
• “CALL” appears when call channel is selected.
➥ While pushing and holding [H/L], push to select one of
➥ Push and hold for 3 sec. to enter call channel program-
12
three channel groups in sequence depending on ver-
sion. (p. 8)
ming condition when call channel is selected. (p. 10) 13
• EUR version has International channels only and this func- !3 KEYPAD 14
tion is not available. ➥ Inputs numeral for channel number input, etc.
• After inputting the desired channel number, push [ENT]. 15
u SQUELCH CONTROL [SQL] (p. 8)
Rotate to set the squelch threshold level. • Push and hold [0•A] to input ‘A’ for simplex channels. 16
➥ Inputs numeral, alphabet and some symbols for chan-
i MIC CONNECTOR nel comment input.
Connect the optional hand microphone only. (p. 116) ➥ After pushing [F], push to perform the secondary function.
C AUTION: NEVER connect the optional handset • M ost of secondary function (except TAG channel setting;
(HS-98) here. p. 16, print out operation; p. 12) can be cleared or cancelled
when [CLR] is pushed.
3
2 PANEL DESCRIPTION
4
PANEL DESCRIPTION 2
n Function display 1
2
!0 POWER !1 DUPLEX INDICATOR
INDICATOR
3
!2 CHANNEL GROUP
INDICATOR 4
o BUSY/TRANSMIT q CALL CHANNEL
INDICATOR INDICATOR 5
BUSY 25W INT CALL 6
i TAG CHANNEL DUP
INDICATOR 7
TAG w MESSAGE
8
INDICATOR
u SCAN INDICATOR NORMAL SCAN
9
e CHANNEL NUMBER 10
y POSITION 34°34.506N
READOUT 11
INDICATOR 123°23.236W
t TIME ZONE UTC 1:10 CALLING r CHANNEL COMMENT 12
INDICATOR INDICATOR 13
14
15
q CALL CHANNEL INDICATOR (pgs. 7, 10) e CHANNEL NUMBER READOUT
Appears when the call channel is selected. Indicates the selected operating channel number. 16
w MESSAGE INDICATOR (pgs. 33, 75, 92) r CHANNEL COMMENT INDICATOR
Blinks when the unread message is stored in the Call Log Channel comment appears if programmed. (p. 11)
memory.
5
2 PANEL DESCRIPTION
u SCAN INDICATOR
➥ “ PRI-SCAN 16” appears during Priority scan;
“NORMAL SCAN” appears during Normal scan.
(p. 16)
➥ “DUAL 16” appears during Dualwatch; “TRI 16” ap-
pears during Tri-watch. (p. 14)
6
BASIC OPERATION 3
n Channel selection 1
2
D Channel 16 D Call channel
Channel 16 is the distress and safety channel. It is used for Each regular channel group has a separate leisure-use call 3
establishing initial contact with a station and for emergency channel. The call channel is monitored during Tri-watch. The
4
communications. Channel 16 is monitored during both Du- call channels can be programmed (p. 10) and are used to
alwatch and Tri-watch. While standing by, you must monitor store your most often used channel in each channel group 5
[H/L] [DIAL] [CE] KEYPAD [4•
[⁄6•C]16.
Channel ] for quick recall.
[SELECTOR] [CLR] [F] [ENT] [MENU•MMSI]
6
q Push [⁄6•C] momentarily to select Channel 16. q Push and hold [⁄6•C] for 1 sec. to select the call channel 7
of the selected channel group.
25W INT
• “CALL” and call channel number appear. 8
C TAG • Each channel group may have an independent call channel 9
Push 16 after programming a call channel. (p. 10)
34°34.506N
123°23.236W
Appears 10
UTC 12:00 CALLING
Push and hold
25W INT CALL 11
w Push [DIAL] to return to the condition before selecting C TAG
12
16
Channel 16, or rotate [SELECTOR] to select a channel.
• Pushing the keypad or [Y]/[Z] on the microphone also selects
34°34.506N
123°23.236W
13
for 1 sec.
a channel. UTC 12:00 CALLING
14
w Push [DIAL] to return to the condition before selecting 15
call channel, or rotate [SELECTOR] to select a channel.
• Pushing the keypad or [Y]/[Z] on the microphone also selects
16
a channel.
7
3 BASIC OPERATION
8
BASIC OPERATION 3
1
2
y Push and hold [PTT] to transmit, then speak into the mi- t Select the e Change the r Select a
crophone. output power channel group channel 3
• “TX” appears.
• Channel 70 cannot be used for transmission other than DSC. 4
u Release [PTT] to receive. 5
IMPORTANT: To maximize the readability of your trans- 6
C
mitted signal, pause a few sec. after pushing [PTT], hold MIC
16
7
the microphone 5 to 10 cm from your mouth and speak at VOL SQL
10
BASIC OPERATION 3
n Channel comments 1
2
Memory channels can be labeled with a unique alphanu- Push
meric ID of up to 10 characters each. 3
25W INT
11
3 BASIC OPERATION
PLEASURE
• A low beep tone sounds while [H/L] is pushed and held to drain 10
water, regardless of [VOL] control setting.
• The transceiver never accepts a key operation while the Aqua- 11
Quake function is activated.
✔ For DSC operation
• After releasing [H/L], the transceiver returns to the normal op-
12
When the backlight blinks during DSC operation (receiving
a call, [DISTRESS] is pushed and held, etc.), the backlight
eration condition. 13
level 7 (Max.) and OFF (Min.) are repeated alternately re-
he AquaQuake function should be activated for about 5
T 14
gardless of above setting.
sec. to sufficiently clear water away from the speaker grill. 15
After the blinking stops, the backlight selects level “4” if the
backlight level has been set to OFF or 1 to 3. 16
• If the backlight level is set to 4 to 7, the setting level holds after the
blinking stops.
13
4 DUALWATCH/TRI-WATCH
n Description n Operation
Dualwatch monitors Channel 16 while you are receiving q Select the desired channel.
on another channel; Tri-watch monitors Channel 16 and the w Push [F], then push [1• DUAL ] to start Dualwatch or
call channel while receiving another channel. Dualwatch/Tri- [2• TRI ] to start Tri-watch.
watch is convenient for monitoring Channel 16 when you are • “DUAL 16” appears during Dualwatch; “TRI 16” appears
operating on another channel. during Tri-watch.
• A beep tone sounds when a signal is received on Channel 16.
DUALWATCH/TRI-WATCH SIMULATION e To cancel Dualwatch or Tri-watch, push [CLR] or repeat
Call step w.
channel
[Example]: Operating Tri-watch on INT Channel 25
Ch 16 Ch 88 Ch 88 Ch 16 Ch 88 Ch 23 Tri-watch starts. Signal is received on call
channel.
25W INT BUSY 25W INT CALL
DUP DUP
TAG Appears TAG
TRI 16 TRI 16
14
SCAN OPERATION 5
n Scan types 1
2
Scanning is an efficient way to locate signals quickly over a Set the TAG channels (scanned channel) before scanning.
wide frequency range. The transceiver has Priority scan and Clear the TAG for unwanted channels which inconveniently 3
Normal scan. stop scanning, such as those for digital communication use.
(Refer to the next page for details.)
4
5
hoose the desired scan type from ‘Priority’ or ‘Normal’ in
C
Set mode. (p. 107) 6
7
PRIORITY SCAN NORMAL SCAN
8
Ch 01 Ch 02 Ch 01 Ch 02
9
10
Ch 06 Ch 16
Ch 06
Ch 03
11
Ch 03
12
13
Ch 05 Ch 04 Ch 05 Ch 04
14
15
Priority scan searches through all TAG channels in Normal scan, like priority scan, searches through all TAG 16
sequence while monitoring Channel 16. When a signal channels in sequence. However, unlike priority scan,
is detected on Channel 16, scan pauses until the signal Channel 16 is not checked unless Channel 16 is set as a
disappears; when a signal is detected on a channel other TAG channel.
than Channel 16, scan becomes Dualwatch until the
signal disappears.
15
5 SCAN OPERATION
16
SCAN OPERATION 5
34°34.506N
123°23.236W
UTC 12:00 SAFETY
17
6 DSC OPERATION
Push
IC-GM651
MMSI Input
<MMSI> 123456789
No MMSI
Ver1.000
After
2 sec. MMSI Input
_________
18
DSC OPERATION 6
n DSC address ID 1
2
e After inputting the MMSI code, push [ENT]. A total of 100 DSC address IDs can be programmed and
• ‘Confirmation’ line appears. named with up to 10 characters. 3
MMSI Input
OTE: The transceiver automatically returns to the nor-
N 4
mal operation condition when no operation is performed
123456789
for 10 minutes in DSC menu.
5
6
D Programming Individual ID
Push q Push [MENU] to enter the DSC menu. 7
w Rotate [SELECTOR] to select “Set up,” push [ENT]. 8
MMSI Input
123456789 --DSC Menu--
Select Item
9
Confirmation
_________ Rotate
Distress Call
Received Call Log
≤
10
Position Request
SELECTOR Test Call 11
1st digit blinks ˘Set up
Exit 12
r Input the MMSI code again for the confirmation.
Push Rotate Push 13
SELECTOR
MMSI Input
123456789 e Rotate [SELECTOR] to select “Add:Individual 14
ID,” push [ENT].
Confirmation 15
Rotate --DSC Menu--
CLR
123456789
Set up 16
SELECTOR ˘Add:Individual ID
Add:Group ID
DEL:Individual ID
t Push [ENT] to set. DEL:Group ID Push
• Return to the normal operation condition. Auto Print
• If the different code is input, the code programming is failure. Position Auto ACK ≥
Try steps w to r again.
☞Continue to the next page 19
6 DSC OPERATION
r Input the 9-digit individual ID directly with the keypad. t Input the 10-character of the individual ID name directly
• Rotate [SELECTOR] to move the cursor backward or forward. with the keypad.
• Push [CE] to clear the ID and name. • Rotate [SELECTOR] to move the cursor backward or forward.
• Push [CLR] to cancel and back to the previous screen. • Push [CE] to clear the ID and name.
1st digit blinks • Push [CLR] to cancel and back to the previous screen.
Push 1st character blinks
--DSC Menu--
Add:Individual ID Push
--DSC Menu--
Input 9 Digits Add:Individual ID
_________ Input 9 Digits
Input Name Input the individual ID 123123123
__________ Input Name
CLR __________
Input the individual ID name
--DSC Menu--
Rotate Add:Individual ID --DSC Menu--
Input 9 Digits CLR
Add:Individual ID
123______
Input Name Cursor moves
SELECTOR Rotate Input 9 Digits
123123123
__________ Input Name
SELECTOR
Sta_______
Cursor moves
--DSC Menu--
Add:Individual ID --DSC Menu--
Input 9 Digits Add:Individual ID
12312312_ Input 9 Digits
Input Name 123123123
__________ Input Name
Station_1_
20
DSC OPERATION 6
y Push [ENT] to program and return to the DSC set up menu. i Rotate [SELECTOR] to select “Exit,” push [ENT] to re- 1
turn to the normal operation condition.
--DSC Menu--
Add:Individual ID • Pushing [CLR] also returns to the normal operation condition. 2
Input 9 Digits
123123123 --DSC Menu-- 3
Input Name Select Item
Station_1_ Distress Call ≤ 4
Received Call Log
Push
Rotate Position Request 5
Test Call
--DSC Menu--
Set up
SELECTOR Set up
˘Exit
6
˘Add:Individual ID
Add:Group ID
7
Push
DEL:Individual ID
DEL:Group ID 8
Auto Print
Position Auto ACK ≥ 9
u Rotate [SELECTOR] to select “Exit,” push [ENT] to re-
10
turn to DSC menu. 11
• Pushing [CLR] also returns to DSC menu.
12
--DSC Menu--
Set up 13
DSC Data Output ≤
Rotate
CH70 SQL Level 14
Medical Transports
SELECTOR
Neutral Ship Call
Self Check Test
15
˘Exit
16
Push
21
6 DSC OPERATION
D Deleting Individual ID
q Push [MENU] to enter the DSC menu. r Rotate [SELECTOR] to select the desired ID name for
w Rotate [SELECTOR] to select “Set up,” push [ENT]. deleting, push [ENT].
• Push [CLR] to cancel and back to the previous screen.
--DSC Menu--
Select Item --DSC Menu--
Distress Call ≤ Rotate Select ID
Rotate Received Call Log Station 1
Position Request SELECTOR Station 2
SELECTOR Test Call ˘Station 3
˘Set up Station 4 ≥
Exit
Push
Push
t Push [ENT] to delete the selected individual ID and return
e Rotate [SELECTOR] to select “DEL:Individual to the ID selection screen.
ID,” push [ENT]. • Push [CLR] to cancel and back to the previous screen.
• When no individual ID is programmed, “No ID” is displayed.
Push [CLR] to cancel and back to the previous screen. --DSC Menu--
ID Deletion
--DSC Menu--
Rotate Set up Are You Sure?
Add:Individual ID
SELECTOR Add:Group ID Push to Delete
˘DEL:Individual ID
DEL:Group ID
Push
Auto Print
Position Auto ACK ≥ Push --DSC Menu--
Select ID
˘Station 1
Station 2
Station 4
Station 5 ≥
22
DSC OPERATION 6
D Programming Group ID 1
y Push [CLR] to return to the DSC Set up menu. q Push [MENU] to enter the DSC menu.
• Push [ENT] to delete the selected individual ID. (see step t) w Rotate [SELECTOR] to select “Set up,” push [ENT]. 2
• Push [F], then push [8• PRT ] to print out all the programmed
individual ID. --DSC Menu-- 3
Select Item
u Rotate [SELECTOR] to select “Exit,” push [ENT] to re- Distress Call ≤ 4
turn to DSC menu. Rotate Received Call Log
• Pushing [CLR] also returns to DSC menu. Position Request 5
SELECTOR Test Call
--DSC Menu-- ˘Set up 6
Set up Exit
DSC Data Output ≤
Push
7
CH70 SQL Level
Rotate Medical Transports 8
Neutral Ship Call
e Rotate [SELECTOR] to select “Add:Group ID,” push
SELECTOR Self Check Test
˘Exit [ENT]. 9
Rotate --DSC Menu-- 10
Push Set up
SELECTOR Add:Individual ID 11
i Rotate [SELECTOR] to select “Exit,” push [ENT] to re- ˘Add:Group ID
12
DEL:Individual ID
turn to the normal operation condition. DEL:Group ID
• Pushing [CLR] also returns to the normal operation condition. Auto Print Push 13
Position Auto ACK ≥
--DSC Menu-- 14
Select Item
Distress Call
Received Call Log
≤
☞Continue to the next page
15
Rotate Position Request
Test Call
16
SELECTOR Set up
˘Exit
Push
23
6 DSC OPERATION
r Input the 8-digit group ID directly with the keypad. t Input the 10-character of the group ID name directly with
• Rotate [SELECTOR] to move the cursor backward or forward. the keypad.
• Push [CE] to clear the ID and name. • Rotate [SELECTOR] to move the cursor backward or forward.
• Push [CLR] to cancel and back to the previous screen. • Push [CE] to clear the ID and name.
1st digit ‘0’ is fixed for a Group ID. • Push [CLR] to cancel and back to the previous screen.
2nd digit blinks 1st digit blinks
Push Push
--DSC Menu-- --DSC Menu--
Add:Group ID Add:Group ID
Input 8 Digits Input 8 Digits
0________ 012345678
Input Name Input the group ID Input Name
__________ __________
CLR
Input the group ID name
--DSC Menu-- --DSC Menu--
CLR
Rotate Add:Group ID Add:Group ID
Input 8 Digits Rotate Input 8 Digits
012______ 012345678
Input Name Cursor moves
SELECTOR
Input Name
SELECTOR
__________ Gro_______
Cursor moves
--DSC Menu-- --DSC Menu--
Add:Group ID Add:Group ID
Input 8 Digits Input 8 Digits
01234567_ 012345678
Input Name Input Name
__________ Group_A___
24
DSC OPERATION 6
y Push [ENT] to program and return to the DSC Set up i Rotate [SELECTOR] to select “Exit,” push [ENT] to re- 1
menu. turn to the normal operation condition.
• Pushing [CLR] also returns to the normal operation condition. 2
--DSC Menu--
Add:Group ID --DSC Menu-- 3
Input 8 Digits Select Item
012345678
Input Name
Distress Call ≤ 4
Received Call Log
Group_A___ Rotate Position Request 5
Test Call
Push SELECTOR Set up
˘Exit
6
--DSC Menu--
Set up 7
˘Add:Group ID Push
DEL:Individual ID 8
DEL:Group ID
Auto Print
Position Auto ACK
9
DSC Data Output ≥ 10
u Rotate [SELECTOR] to select “Exit,” push [ENT] to re- 11
turn to DSC menu.
• Pushing [CLR] also returns to DSC menu. 12
--DSC Menu-- 13
Set up
DSC Data Output ≤ 14
CH70 SQL Level
Rotate Medical Transports 15
Neutral Ship Call
SELECTOR Self Check Test 16
˘Exit
Push
25
6 DSC OPERATION
D Deleting Group ID
q Push [MENU] to enter the DSC menu. r Rotate [SELECTOR] to select the desired ID name for
w Rotate [SELECTOR] to select “Set up,” push [ENT]. deleting.
• Push [CLR] to cancel and back to the previous screen.
--DSC Menu--
Select Item --DSC Menu--
Distress Call ≤ Rotate Select ID
Rotate Received Call Log Icom
Position Request SELECTOR Group A
SELECTOR Test Call ˘Group B
˘Set up Group C
Exit
Push
Push
t Push [ENT] to delete the selected group ID and return to
e Rotate [SELECTOR] to select “DEL:Group ID,” push the ID selection screen.
[ENT].
--DSC Menu--
• When no group ID is programmed, “No ID” is displayed. Push ID Deletion
[CLR] to cancel and back to the previous screen.
Are You Sure?
--DSC Menu--
Select Item Push to Delete
Rotate Add:Individual ID
Add:Group ID
SELECTOR DEL:Individual ID Push
˘DEL:Group ID --DSC Menu--
Auto Print Select ID
Position Auto ACK ≥ Icom
Push Group A
˘Group C
26
DSC OPERATION 6
Push
27
6 DSC OPERATION
e Input your latitude data directly with the keypad. After in- r Input your longitude data directly with the keypad. After
putting, push [ENT] to set. inputting, push [ENT] to set.
• P ush [6• MNO ] to input N; North latitude or [7• PRS ] to input • Push [9•WXY] to input W; West longitude or [3•DEF] to input
S; South latitude. E; East longitude.
• Rotate [SELECTOR] to move the cursor backward or forward. • Rotate [SELECTOR] to move the cursor backward or forward.
• P ush [CE] to clear the input latitude data. When [ENT] is • P ush [CE] to clear the input longitude data. When [ENT] is
pushed after pushing [CE], no position and time data are set. pushed after pushing [CE], no position and time data are set.
• Push [CLR] to cancel and exit the condition. • Push [CLR] to cancel and exit the condition.
1st digit blinks Push 1st digit blinks
Push
--DSC Menu-- --DSC Menu--
Input Latitude Input Longitude
__°__.___N ___°__.___W
Input your latitude data Input your longitude data
CLR
CLR
--DSC Menu-- --DSC Menu--
Input Latitude Input Longitude
Rotate 34°3_.___N Rotate 123°2_.___W
Cursor moves Cursor moves
SELECTOR SELECTOR
Push Push
28
DSC OPERATION 6
t Input the current UTC time with the keypad. After input- NOTE: When no position and time data are input, the fol- 1
ting, push [ENT] to set. lowing screen appears. Push [ENT] to set.
• Rotate [SELECTOR] to move the cursor backward or forward. • Push [CLR] to cancel and back to the previous screen. 2
• Push [CE] to clear the input time data. When [ENT] is pushed
after pushing [CE], no position and time data are set. --DSC Menu-- 3
No Position Data
• Push [CLR] to cancel and back to the previous screen. No Time Data 4
• After pushing [ENT], return to the DSC menu.
Push 1st digit blinks Are You Sure? 5
--DSC Menu-- 6
Input UTC Time
__:__ Push 7
Input the current UTC time
y Rotate [SELECTOR] to select “Exit,” push [ENT] to re- 8
CLR
--DSC Menu--
Input UTC Time
turn to the normal operation condition. 9
• Pushing [CLR] also returns to the normal operation condition.
Rotate 12:__
10
Cursor moves --DSC Menu--
SELECTOR
Select Item
Distress Call ≤
11
--DSC Menu--
Input UTC Time
12:00 Rotate
Received Call Log
Position Request
12
SELECTOR
Test Call
Set up
13
˘Exit
14
Push 15
Push
16
29
6 DSC OPERATION
TAG
When a GPS receiver (IEC61162-1: 2000 format) is con-
nected, the transceiver displays the current position and time
• Latitude : 34˚34.506N (“ ” appears.) When no GPS receiver is connected, the
34°34.506N • Longitude : 123˚23.236W
123°23.236W transceiver displays the manually entered position and time.
MNL 12:00 CALLING • UTC Time : 12:00
A GPS receiver appropriate for the IC-GM651 is not supplied
When no position and time data are set. from Icom. A GPS receiver with IEC61162-1: 2000 format
is required for position and time indication. Ask your dealer
25W INT
about suitable GPS receivers.
TAG
25W INT
TAG
No Position “No Position” and
No Time “No Time” are displayed.
CALLING
34°34.506N
123°23.236W
UTC 12:00 CALLING
NOTE:
When the transceiver displays the manually
entered position and time, “ ” does not ap-
pear and “MNL” is displayed instead of “UTC”.
30
DSC OPERATION 6
31
6 DSC OPERATION
n Distress call
A Distress call should be transmitted, if in the opinion of the D Simple call
Master, the ship or a person is in distress and requires im- q Confirm no Distress call is being received.
mediate assistance. w Lift up the key cover, then push and hold [DISTRESS] for
3 sec. to transmit the Distress call.
• Emergency channel (Channel 70) is automatically selected and
Other ship About 20 to 30 miles the Distress call is transmitted.
(Sea area A1) • When no GPS is connected, input your position and UTC time,
if possible.
• While pushing [DISTRESS], the key backlight blinks and count-
Distress Alert down alarm is emitted.
Transmission Push and hold
Distress Call
Coast Station
Push for 3 sec.
for 3 sec.
Ship in Distress
Transmitting
32
DSC OPERATION 6
1
2
e After transmitting the call, the transceiver waits for an ac- ➥ A distress alert contains (default); 3
knowledgment call. • Nature of distress : Undesignated distress
• The Distress call is automatically transmitted every 3.5 to 4.5 • Position data : GPS or manual input position data held
4
minutes. (‘Distress Call Repeat’ mode; p. 38) for 23.5 hrs. 5
• [PTT] is activated for voice communication with a maritime sta- ➥T he Distress call is repeated every 3.5–4.5 min., until
tion via Channel 16. receiving an ‘acknowledgement.’ (‘Distress Call Repeat’ 6
25W INT mode; p. 38) 7
➥ Push [CLR] to transmit the ‘Distress Cancel’ to cancel
TAG the ‘Distress Call Repeat’ mode. (p. 38) 8
➥ Push [DISTRESS] to transmit a renewed Distress call,
Waiting for 9
DistressACK if required.
➥ “??” may blink instead of position and time indications 10
and the alarm sounds when the GPS data is invalid, or
has not been manually updated after 4 hours.
11
r After receiving the acknowledgment, reply using the mi-
crophone. ➥ If the transceiver has no MMSI code, a warning 12
Blinks when the acknowl- alarm is emitted and “No MMSI” is displayed when
edgement is received. [DISTRESS] is pushed. In this case, the MMSI code 13
25W INT
programming screen appears automatically. (p. 18) 14
TAG
15
Received
DistressACK 16
<Coast St.1
D Regular call
The nature of the distress should be included in the Distress call.
When the transceiver receives the GPS data from the
connected GPS receiver, the following screens (steps e
q Push [MENU] to enter the DSC menu, then rotate [SE-
to t) do not appear. Go to step y at p. 36.
LECTOR] to select “Distress Call”, push [ENT].
--DSC Menu--
e Input your latitude data directly with the keypad (if you want to
Select Item change the displayed data). After inputting, push [ENT] to set.
Rotate Individual Call ≤ • If the data is not necessary to be changed, push [ENT] to skip
Group Call the input step.
SELECTOR ˘Distress Call
Received Call Log • P ush [6• MNO ] to input N; North latitude or [7• PRS ] to input
Position Request S; South latitude.
Test Call ≥ Push • Rotate [SELECTOR] to move the cursor backward or forward.
• Push [CE] to clear the position and time data. (p. 36)
w Rotate [SELECTOR] to select the nature of the distress, • Push [CLR] to cancel and back to the previous screen.
push [ENT]. Push --DSC Menu--
• ‘Undesignated,’ ‘Fire, Explosion,’ ‘Flooding,’ ‘Collision,’ ‘Grounding,’ Input Latitude 1st digit blinks
‘Capsizing,’ ‘Sinking,’ ‘Adrift,’ ‘Abandoning Ship,’ ‘Piracy (Piracy at- 34°34.506N
tack)’ and ‘Man Overboard’ are available. Input your latitude data
• The selected nature of the distress is stored.
• Push [CLR] to cancel and back to the previous screen. --DSC Menu--
CLR
Input Latitude
--DSC Menu-- 25°25.506N
Select Nature Rotate
˘Undesignated Cursor moves
Fire,Explosion SELECTOR
Rotate --DSC Menu--
˘UndesignatedFlooding
Fire,Explosion
Collision ≥ Input Latitude
SELECTOR
Flooding 25°25.415N
Collision Push
Set ‘N’ (North) or
Grounding or
Capsizing ‘S’ (South) Push
Sinking
Adrift
Abandoning Ship
Piracy * This illustration shows that the transceiver does not receive
Push
Man Overboard the position data from the connected GPS receiver. If the
34 transceiver has no position data, ‘_’ (under bar) is indicated.
DSC OPERATION 6
1
r Input your longitude data directly with the keypad (if you want to t Input the current UTC time data directly with the keypad
change the displayed data). After inputting, push [ENT] to set. (if you want to change the displayed data). After inputting, 2
• If the data is not necessary to be changed, push [ENT] to skip push [ENT] to set.
the input step. • If the data is not necessary to be changed, push [ENT] to skip
3
• Push [9•WXY] to input W; West longitude or [3•DEF] to input the input step. 4
E; East longitude. • Rotate [SELECTOR] to move the cursor backward or forward.
• Rotate [SELECTOR] to move the cursor backward or forward. • Push [CE] to clear the position and time data. (p. 36) 5
• Push [CE] to clear the position and time data. (p. 36) • Push [CLR] to cancel and back to the previous screen.
• Push [CLR] to cancel and back to the previous screen. 6
Push 1st digit blinks
Push 1st digit blinks
--DSC Menu--
7
--DSC Menu--
Input Longitude
Input UTC Time
12:00 8
123°23.236W
Input your longitude data
Input the current UTC time 9
10
CLR
CLR --DSC Menu--
--DSC Menu-- Input UTC Time
Input Longitude Rotate 12:1_ 11
Rotate 154°13.236W Cursor moves
Cursor moves SELECTOR 12
SELECTOR
--DSC Menu--
--DSC Menu-- Input UTC Time 13
Input Longitude 12:15
Push
154°11.106W 14
or Set ‘W’ (West) or 15
‘E’ (East)
16
Push
Push
* This illustration shows that the transceiver does not receive
* This illustration shows that the transceiver does not receive the UTC time data from the connected GPS receiver. If the
the position data from the connected GPS receiver. If the transceiver has no time data, ‘_’ (under bar) is indicated.
transceiver has no position data, ‘_’ (under bar) is indicated.
☞Continue to the next page
35
6 DSC OPERATION
NOTE: When no position and time data are input, the fol- y Push and hold [DISTRESS] for 3 sec. to transmit the Dis-
lowing screen appears. Push [ENT] to set. tress call.
• Push [CLR] to cancel and back to the previous screen. • Emergency channel (Channel 70) is automatically selected and
the Distress call is transmitted.
--DSC Menu-- • While pushing [DISTRESS], the key backlight blinks and count-
No Position Data
No Time Data down alarm is emitted.
• The distress information is stored.
Are You Sure? • Push [CLR] to exit the condition.
Distress Call
Push
Push [DISTRESS]
Push and hold for 3 sec.
Distress Call
for 3 sec.
Push for 3 sec.
TX
Distress Call
Transmitting
Transmitting
36
DSC OPERATION 6
u After transmitting the Distress call, the transceiver waits ➥T he Distress call is repeated every 3.5–4.5 min., until re- 1
for an acknowledgment call. ceiving an ‘acknowledgement.’ (‘Distress Call Repeat’
• The Distress call is automatically transmitted every 3.5 to 4.5 mode; p. 38) 2
minutes. (‘Distress Call Repeat’ mode; p. 38) ➥ Push [CLR] to transmit the ‘Distress Cancel’ to cancel
• [PTT] is activated for voice communication with a maritime sta-
3
the ‘Distress Call Repeat’ mode. (p. 38)
tion via Channel 16. ➥ Push [DISTRESS] to transmit a renewed Distress call, 4
if required.
25W INT
5
➥ “??” may blink instead of position and time indications
TAG
and the alarm sounds when the GPS data is invalid, or 6
Waiting for has not been manually updated after 4 hours.
DistressACK 7
8
i After receiving the acknowledgment, reply using the mi- 9
crophone. 10
Blinks when the acknowl-
edgement is received. 11
25W INT 12
TAG 13
Received
DistressACK
<Coast St.1
14
15
After receiving the acknowl-
16
edgment from Coast St.1.
• “<” means “from.”
37
6 DSC OPERATION
Re-transmitting
38
DSC OPERATION 6
Push
39
6 DSC OPERATION
e The distress information appears. Push [ENT]. t After transmitting the Distress Acknowledgement call, the
transceiver selects the Channel 16 automatically.
--DSC Menu--
Distress Information 25W INT
Rotate Distress ID
121111113 TAG
SELECTOR Undesignated
LAT: 12°23.111N
LON:123°23.123E 34°34.506N
UTC:10:25 ≥ 123°23.236W
UTC 12:00 CALLING
Telephony
Push
--DSC Menu--
Distress ACK
Push to Transmit
Push TX
Distress ACK
Transmitting
Transmitting
40
DSC OPERATION 6
41
6 DSC OPERATION
e Rotate [SELECTOR] to select the desired pre-pro- r D istress ID of the ship in distress selection screen
grammed coast station address or “Manual Input” appears. Rotate [SELECTOR] to select “Manual
for transmitting a distress relay call, push [ENT]. Input,” push [ENT].
• The ID code can be set in advance. (p. 19)
Rotate --DSC Menu--
Select Distress ID
--DSC Menu--
˘Manual Input
Rotate Select Address SELECTOR
Ship 1
Manual Input
Ship 2
SELECTOR ˘Coast St.1 Push
Ship 3
Coast St.2
Push
Distress Call Log is displayed after receiving the Distress Call.
When the pre-programmed Do not select for DROBOSE.
address is selected.
When “Manual Input” is selected, set the 7-digit ad-
dress ID you wish to call with the keypad, push [ENT].
• 1st and 2nd digits ‘00’ are fixed for a coast station ID.
Push
--DSC Menu--
Input Address ID
001111112
CLR
Push
42
DSC OPERATION 6
t Input the 9-digit Distress ID (MMSI ID) code of the ship in y Rotate [SELECTOR] to select the nature of the distress, 1
distress that you wish to help with the keypad. push [ENT].
• Rotate [SELECTOR] to move the cursor backward or forward. • ‘Undesignated,’ ‘Fire Explosion,’ ‘Flooding,’ ‘Collision,’ ‘Grounding,’ 2
• Push [CE] to clear the input data. ‘Capsizing,’ ‘Sinking,’ ‘Adrift,’ ‘Abandoning Ship,’ ‘Piracy (Piracy at-
• Push [CLR] to cancel and back to the previous condition. tack),’ ‘Man Overboard’ and ‘EPIRB Emission’ are available.
3
• If nothing is input, MMSI ID code is set as “Null.” • The selected nature of the distress is stored after selecting is 4
Push 1st digit blinks finished.
--DSC Menu--
5
--DSC Menu--
Input Distress ID
_________
Select Nature
˘Undesignated
6
Input the Distress ID Rotate
Fire,Explosion
˘UndesignatedFlooding
7
Collision ≥
CLR
--DSC Menu-- SELECTOR
Fire,Explosion
Flooding
8
Input Distress ID
Rotate 1212_____
Collision
Grounding
9
Cursor moves
SELECTOR
Capsizing
Sinking 10
Adrift
--DSC Menu--
Input Distress ID Abandoning Ship 11
Piracy
121212121
Man Overboard Push 12
EPIRB Emission
13
☞Continue to the next page 14
Push 15
16
43
6 DSC OPERATION
u Your position data is displayed. Input the ship in distress i Input the ship in distress longitude data directly with the
latitude data directly with the keypad. After inputting, push keypad. After inputting, push [ENT] to set.
[ENT] to set. • If the data is not necessary to be changed, push [ENT] to skip
• If the data is not necessary to be changed, push [ENT] to skip the input step.
the input step. • Push [9•WXY] to input W; West longitude or [3•DEF] to input
• P ush [6• MNO ] to input N; North latitude or [7• PRS ] to input E; East longitude.
S; South latitude. • Rotate [SELECTOR] to move the cursor backward or forward.
• Rotate [SELECTOR] to move the cursor backward or forward. • Push [CE] to clear the position and time data. (p. 45)
• Push [CE] to clear the position and time data. (p. 45) • Push [CLR] to cancel and back to the previous screen.
• Push [CLR] to cancel and back to the previous screen. Push 1st digit blinks
1st digit blinks
Push --DSC Menu--
--DSC Menu-- Input Longitude
Input Latitude 123°23.236W
34°34.506N Input your longitude data
Input your latitude data CLR
--DSC Menu--
CLR
--DSC Menu-- Input Longitude
Input Latitude
Rotate 154°13.236W
Rotate 25°25.506N Cursor moves
SELECTOR
Cursor moves
SELECTOR --DSC Menu--
--DSC Menu-- Input Longitude
Input Latitude 154°11.106W
Push
25°25.415N
Push or Set ‘W’ (West) or
or Set ‘N’ (North) or ‘E’ (East)
‘S’ (South)
44
DSC OPERATION 6
o Input the current UTC time with the keypad. After input- NOTE: When no position and time data are input, the fol- 1
ting, push [ENT] to set. lowing screen appears. Push [ENT] to set.
• If the data is not necessary to be changed, push [ENT] to skip • Push [CLR] to cancel and back to the previous screen. 2
the input step.
• Rotate [SELECTOR] to move the cursor backward or forward. --DSC Menu-- 3
No Position Data
• Push [CE] to clear the position and time data. (see at right) No Time Data 4
• Push [CLR] to cancel and back to the previous screen.
Push 1st digit blinks Are You Sure? 5
--DSC Menu-- 6
Input UTC Time
12:00
Push 7
Input the current UTC time
8
CLR
--DSC Menu--
Input UTC Time
9
Rotate 12:1_
10
Cursor moves
SELECTOR
11
--DSC Menu--
Input UTC Time
12:15
12
13
14
15
* If the transceiver has no time data,
Push
16
‘_’ (under bar) is indicated.
45
6 DSC OPERATION
!0 Push [ENT] to transmit the distress relay call. To transmit the distress relay call with “Distress Call Log”:
• Emergency channel (Channel 70) is automatically selected. You can relay a distress call after receiving the distress call.
--DSC Menu-- Distress Relay
Distress Relay Distress Transmission
Push to Transmit
Coast Station
Your ship
Push TX
Distress Relay
Ship in Distress
Transmitting q After receiving the distress call (p. 75), push [MENU] to
enter the DSC menu, then rotate [SELECTOR] to select
“Distress Relay,” push [ENT].
Transmitting Rotate --DSC Menu--
Select Item
!1 After transmitting the Distress Relay call, the transceiver SELECTOR ˘Distress Relay
returns to the normal operation condition. All Ships Call
• [PTT] is activated for voice communication with a maritime sta- Individual Call
Group Call Push
tion via Channel 16. Distress Call
Received Call Log ≥
25W INT
Push
46
DSC OPERATION 6
1
When “All Ships” is selected, step e does not ap- r Distress ID of the ship in distress selection screen ap-
pear. Go to step r. pears. Rotate [SELECTOR] to select the desired distress 2
ID from the distress call log, push [ENT]. 3
e Rotate [SELECTOR] to select the desired pre-pro-
grammed coast station address or “Manual Input” Rotate
--DSC Menu--
Select Distress ID 4
for transmitting a distress relay call, push [ENT]. Manual Input
• The ID code can be set in advance. (p. 19) SELECTOR ˘Ship 1 5
Ship 2
--DSC Menu--
Ship 3 6
Push
Rotate Select Address
Manual Input
7
SELECTOR ˘Coast St.1
Coast St.2 Distress Call Log is displayed after 8
receiving the Distress Call.
Push 9
t The distress information appears. Push [ENT].
10
When the pre-programmed --DSC Menu--
address is selected. Distress Information 11
Rotate Distress ID
When “Manual Input” is selected, set the 7-digit ad- 121212121
Undesignated
12
dress ID you wish to call with the keypad, push [ENT]. SELECTOR
• 1st and 2nd digits ‘00’ are fixed for a coast station ID.
LAT: 12°23.111N
LON:123°23.123E
13
Push
--DSC Menu--
UTC:10:25 ≥
14
Telephony
Input Address ID
001111112 Push 15
16
CLR
Push
47
6 DSC OPERATION
y Push [ENT] to transmit the distress relay call. D Transmitting a Distress Relay Acknowledgement call
• Emergency channel (Channel 70) is automatically selected. Distress relay acknowledgement call operation is available
--DSC Menu-- only when the distress relay call is received.
Distress Relay
TAG Push
34°34.506N
123°23.236W
UTC 12:00 CALLING
48
DSC OPERATION 6
1
e The distress information appears. Push [ENT]. t After transmitting the Distress Relay Acknowledgement
call, the transceiver selects the Channel 16 automatically. 2
--DSC Menu--
Rotate Distress Relay Info 25W INT 3
From Station 1
SELECTOR Distress ID
121212121
TAG 4
Undesignated
LAT: 12°23.111N
5
34°34.506N
LON:123°23.123E ≥ 123°23.236W 6
UTC:10:25 UTC 12:00 CALLING
Telephony Push 7
8
r Push [ENT] to transmit the Distress Relay Acknowledge- 9
ment call.
• Emergency channel (Channel 70) is automatically selected. 10
--DSC Menu-- 11
Distress Relay ACK
12
Are You Sure?
13
Push to Transmit
14
TX
15
Push
Distress Relay ACK
16
Transmitting
Transmitting
49
6 DSC OPERATION
50
DSC OPERATION 6
1
2
r Push [ENT] to transmit the All ships call. t After the All ships call has been transmitted, the trans-
• Emergency channel (Channel 70) is automatically selected. ceiver selects the traffic channel (specified in step e) 3
• If Channel 70 is busy, the transceiver stands by until the chan- automatically.
nel becomes clear. 4
--DSC Menu--
25W INT
5
All Ships Call TAG
6
34°34.506N 7
Push to Transmit 123°23.236W
UTC 12:00 CALLING 8
Push TX
9
All Ships Call
10
Transmitting 11
12
13
Transmitting
14
All Ships Call 15
CH70 BUSY 16
51
6 DSC OPERATION
Voice communication
Only when ‘Able to comply’ is
received.
52
DSC OPERATION 6
1
When “Manual Input” is selected, set the 9-digit indi- r Rotate [SELECTOR] to select the desired intership chan-
vidual ID you wish to call with the keypad, push [ENT]. nel or “Manual Input,” push [ENT]. 2
• Intership channels are already preset into the transceiver in
Push
--DSC Menu-- recommended order.
3
Input Address ID
123123123 --DSC Menu--
4
Select Intership CH
˘08 5
69
CLR
Rotate ˘08
69 77 6
Push 06 ≥
SELECTOR 77
06 7
e Rotate [SELECTOR] to select the desired category, push
[ENT].
09
10 8
13
Rotate --DSC Menu-- 67 9
72
SELECTOR
Select Category
˘Routine 73 10
Safety 15 Push
Urgency 17 11
Manual Input
Push 12
hen “Manual Input” is selected, rotate [SELECTOR]
W
to select the desired channel. The following channels can 13
When the coast station address is selected in step w,
be set; 14
01 06 11 16 21 26 62 67 73 78 83 88
step r does not appear. Go to step t. 02 07 12 17 22 27 63 68 74 79 84 15
03 08 13 18 23 28 64 69 75 80 85
04 09 14 19 24 60 65 71 76 81 86
16
05 10 15 20 25 61 66 72 77 82 87
53
6 DSC OPERATION
t Push [ENT] to transmit the Individual call. D Transmitting an Individual Acknowledgement call
• Emergency channel (Channel 70) is automatically selected. When receiving an Individual call, you can transmit an ac-
• If Channel 70 is busy, the transceiver stands by until the chan- knowledgement call (‘Able to comply’, ‘Propose New Chan-
nel becomes clear. nel’ or ‘Unable to comply’) by using the on screen prompts
--DSC Menu-- (Quick ACK). Also, you can send an acknowledgement
Individual Call through the menu system (Manual ACK.)
54
DSC OPERATION 6
1
To transmit “Able to Comply”— Manual ACK:
q P ush [MENU] to enter the DSC menu, then rotate e The call information appears, push [ENT]. 2
[SELECTOR] to select “Individual ACK,” push [ENT]. 3
--DSC Menu--
• “Individual ACK” is added to the DSC menu after receiv- Individual Call Info
ing an Individual call. From Station 1 4
Routine
--DSC Menu-- Telephony 5
Select Item CH08
Rotate
Distress Relay
All Ships Call
6
Push
Individual Call
˘Individual ACK
7
SELECTOR
r Rotate [SELECTOR] to select “Able to Comply,”
Group Call
Distress Call ≥ push [ENT]. 8
Push
Rotate --DSC Menu-- 9
w Rotate [SELECTOR] to select the desired individual ad- Select Action
˘Able to Comply 10
dress or ID code, push [ENT]. SELECTOR
Propose New Channel
--DSC Menu--
Unable to Comply 11
Push
Rotate Select Address
˘Station 1
12
SELECTOR Station 2
Station 3 13
Push
☞Continue to the next page 14
15
16
55
6 DSC OPERATION
t Push [ENT] to transmit the Individual acknowledgement To transmit “Propose New Channel”— Quick ACK:
call to the calling station. ➥ After an Individual call is received, push [CLR] to stop the
• Emergency channel (Channel 70) is automatically selected. alarm, then rotate [SELECTOR] to indicate the received
• If Channel 70 is busy, the transceiver stands by until the chan- message log. And then, push [ENT]. (Go to step r as at
nel becomes clear. right.)
--DSC Menu-- --DSC LOG--
Individual ACK Individual Call
From Station 1
Routine
Telephony
Push to Transmit CH08
Push
Push TX
Individual ACK
To transmit “Propose New Channel”— Manual ACK:
q Push [MENU] to enter the DSC menu, then rotate [SELEC-
Transmitting
TOR] to select “Individual ACK,” push [ENT].
• “Individual ACK” is added to the DSC menu after receiv-
ing an Individual call.
Transmitting --DSC Menu--
Select Item
y After the Individual acknowledgement call has been trans- Distress Relay
mitted, the specified channel (specifiedACK
Individual by the calling sta- Rotate All Ships Call
Individual Call
tion) is selected automatically.
CH70 BUSY SELECTOR ˘Individual ACK
Group Call
25W INT Distress Call ≥
Push
TAG
56
DSC OPERATION 6
1
w Rotate [SELECTOR] to select the desired individual ad- t Rotate [SELECTOR] to select a desired intership channel
dress or ID code, push [ENT]. or “Manual Input,” push [ENT]. 2
• Intership channels are already preset into the transceiver in
--DSC Menu--
recommended order.
3
Rotate Select Address
˘Station 1
--DSC Menu--
4
SELECTOR Station 2
Station 3
Push
Select Intership CH
08 5
˘69
Rotate
08
˘69 77 6
06 ≥
77
06 7
e The call information appears, push [ENT]. SELECTOR
09
10 8
--DSC Menu-- 13
Individual Call Info
From Station 1
67 9
72
Routine
Telephony
73 10
15 Push
CH08 17 11
Manual Input
Push
12
hen “Manual Input” is selected, rotate [SELECTOR]
W
r Rotate [SELECTOR] to select “Propose New Channel,”
to select the desired channel. The following channels can 13
push [ENT].
be set; 14
--DSC Menu-- 01 06 11 16 21 26 62 67 73 78 83 88
Rotate Select Action
02 07 12 17 22 27 63 68 74 79 84 15
Able to Comply
SELECTOR ˘Propose New Channel
Unable to Comply
03
04
08
09
13
14
18
19
23
24
28
60
64
65
69
71
75
76
80
81
85
86
16
05 10 15 20 25 61 66 72 77 82 87
Push
☞Continue to the next page
57
6 DSC OPERATION
y Push [ENT] to transmit the Individual acknowledgement To transmit “Unable to Comply”— Quick ACK:
call to the calling station. ➥ After an Individual call is received, push [CLR] to stop the
• Emergency channel (Channel 70) is automatically selected. alarm, then rotate [SELECTOR] to indicate the received
• If Channel 70 is busy, the transceiver stands by until the chan- message log. And then, push [ENT]. (Go to step r as at
nel becomes clear. p. 59.)
--DSC Menu-- --DSC LOG--
Individual ACK Individual Call
From Station 1
Routine
Telephony
Push to Transmit CH08
Push
Push TX
Individual ACK
To transmit “Unable to Comply”— Manual ACK:
Transmitting q Push [MENU] to enter the DSC menu, then rotate
[SELECTOR] to select “Individual ACK,” push
[ENT].
• “Individual ACK” is added to the DSC menu after receiv-
Transmitting ing an Individual call.
u After the Individual acknowledgement call has been trans- --DSC Menu--
mitted, the specified channel (specifiedACK
Individual in step t) is se- Select Item
Distress Relay
lected automatically. Rotate All Ships Call
CH70 BUSY
Individual Call
25W INT
SELECTOR ˘Individual ACK
Group Call
TAG
Distress Call ≥
Push
When Channel 70 is
34°34.506N busy
123°23.236W
UTC 12:00 PLEASURE
58
DSC OPERATION 6
1
w Rotate [SELECTOR] to select the desired individual ad- r Rotate [SELECTOR] to select “Unable to Comply,”
dress or ID code, push [ENT]. push [ENT]. 2
--DSC Menu-- --DSC Menu-- 3
Rotate Select Address Select Action
˘Station 1 Rotate Able to Comply 4
SELECTOR Station 2 Propose New Channel
Station 3 SELECTOR ˘Unable to Comply 5
Push
Push
6
7
e The call information appears, push [ENT]. t Rotate [SELECTOR] to select the reason, push [ENT].
• The selected reason will be transmitted. 8
--DSC Menu--
Individual Call Info --DSC Menu-- 9
From Station 1 Select Reason
Routine ˘No Reason Given 10
Telephony Rotate Congestion
˘No Reason Given
CH08 Congestion Busy 11
SELECTOR Busy Queue Indication ≥
Push Queue Indication 12
Station Barred
No Operator
Operator Unavailable
13
Equipment Disabled
Channel Unavailable
14
Mode Unavailable
Push 15
16
☞Continue to the next page
59
6 DSC OPERATION
Group B
Push to Transmit
Push TX
Individual ACK
Your ship
Transmitting
60
DSC OPERATION 6
1
w Rotate [SELECTOR] to select the desired pre-pro- e Rotate [SELECTOR] to select a desired intership channel
grammed group address or “Manual Input,” push or “Manual Input,” push [ENT]. 2
[ENT]. • Intership channels are already preset into the transceiver in 3
• The ID code for the Group call can be set in advance. (p. 23) recommending order.
--DSC Menu--
4
--DSC Menu--
Rotate Select Address
Manual Input
Select Intership CH
˘08 5
69
SELECTOR ˘Group A
Group B
Rotate ˘08
69 77 6
06 ≥
Push
SELECTOR 77
06 7
09
10 8
When the pre-programmed 13
address is selected. 67 9
72
When “Manual Input” is selected, set the 8-digit ID 73 10
code for the group you wish to call with keypad, push 15 Push
[ENT].
17 11
Manual Input
Push 12
--DSC Menu-- hen “Manual Input” is selected, rotate [SELECTOR]
W
Input Address ID
011222223 to select the desired channel. The following channels can 13
be set; 14
01 06 11 16 21 26 62 67 73 78 83 88
CLR 02 07 12 17 22 27 63 68 74 79 84 15
Push 03 08 13 18 23 28 64 69 75 80 85
04 09 14 19 24 60 65 71 76 81 86
16
05 10 15 20 25 61 66 72 77 82 87
61
6 DSC OPERATION
Push to Transmit
62
DSC OPERATION 6
w Rotate [SELECTOR] to select the desired pre-programmed e Push [ENT] to transmit the Position Request call. 1
individual address or “Manual Input,” push [ENT]. • Emergency channel (Channel 70) is automatically selected.
• The ID code for the Individual call can be set in advance. (p. 19) • If Channel 70 is busy, the transceiver stands by until the chan- 2
nel becomes clear.
--DSC Menu-- 3
Rotate Select Address --DSC Menu--
Manual Input Position Request 4
SELECTOR ˘Station 1
Station 2 5
Station 3 ≥
Push Push to Transmit 6
When the pre-programmed 7
Push TX
address is selected. Position Request 8
When “Manual Input” is selected, set the 9-digit indi-
9
vidual ID you wish to call with the keypad, push [ENT]. Transmitting
Push 10
--DSC Menu--
Input Address ID 11
123123123
Transmitting 12
r After the Position Request call has been transmitted, re- 13
CLR
Push turns to the previous condition
Position (before entering the DSC
Request
menu.) CH70 BUSY
14
15
16
When Channel 70 is busy
63
6 DSC OPERATION
--DSC Menu--
Select Item W hen the transceiver receives the GPS data from the
Distress Call ≤ connected GPS receiver, the following screens (steps r
Rotate Received Call Log to y) do not appear. Go to step u at p. 67.
Position Request
SELECTOR ˘Position Reply
Test Call
Set up ≥
Push
64
DSC OPERATION 6
r Input your latitude data directly with the keypad. After in- t Input your longitude data directly with the keypad. After 1
putting, push [ENT] to set. inputting, push [ENT] to set.
• If the data is not necessary to be changed, push [ENT] to skip • If the data is not necessary to be changed, push [ENT] to skip 2
the input step. the input step.
• P ush [6• MNO ] to input N; North latitude or [7• PRS ] to input • Push [9•WXY] to input W; West longitude or [3•DEF] to input 3
S; South latitude. E; East longitude. 4
• Rotate [SELECTOR] to move the cursor backward or forward. • Rotate [SELECTOR] to move the cursor backward or forward.
• Push [CE] to clear the position and time data. (p. 66) • Push [CE] to clear the position and time data. (p. 66) 5
• Push [CLR] to cancel and back to the previous condition. • Push [CLR] to cancel and back to the previous condition.
Push Push 1st digit blinks 6
--DSC Menu--
1st digit blinks
Input Latitude --DSC Menu-- 7
34°34.506N Input Longitude
Input your latitude data 123°23.236W 8
Input your longitude data
--DSC Menu-- 9
CLR CLR
Input Latitude
Rotate 25°25.506N
--DSC Menu--
Input Longitude
10
Cursor moves Rotate 154°13.236W 11
SELECTOR
--DSC Menu-- Cursor moves
Input Latitude
SELECTOR
12
25°25.415N --DSC Menu--
Push Input Longitude 13
Set ‘N’ (North) or 154°11.106W
or Push
‘S’ (South) Push or Set ‘W’ (West) or
14
‘E’ (East) 15
* This illustration shows that the transceiver does not receive 16
the position data from the connected GPS receiver. If the Push
transceiver has no position data, ‘_’ (under bar) is indicated.
* This illustration shows that the transceiver does not receive
the position data from the connected GPS receiver. If the
transceiver has no position data, ‘_’ (under bar) is indicated.
y Input the current UTC time with the keypad. After input- NOTE: When no position and time data are input, the fol-
ting, push [ENT] to set. lowing screen appears. Push [ENT] to set.
• If the data is not necessary to be changed, push [ENT] to skip • Push [CLR] to cancel and back to the previous screen.
the input step.
• Rotate [SELECTOR] to move the cursor backward or forward. --DSC Menu--
No Position Data
• Push [CE] to clear the position and time data. (see at right) No Time Data
• Push [CLR] to cancel and back to the previous screen.
1st digit blinks Are You Sure?
Push
--DSC Menu--
Input UTC Time
12:00
Push
Input the current UTC time
CLR
--DSC Menu--
Input UTC Time
Rotate 12:1_
Cursor moves
SELECTOR
--DSC Menu--
Input UTC Time
12:15
Push
66
DSC OPERATION 6
u Push [ENT] to transmit the Position Reply call to the call- D Transmitting a Polling Reply call 1
ing station. Transmit a Polling Reply call when a Polling Request is re-
• Your position data is transmitted, when [ENT] is pushed. ceived (p. 89). A Polling Request call enables the calling sta- 2
• Emergency channel (Channel 70) is automatically selected.
• If Channel 70 is busy, the transceiver stands by until the chan-
tion to know a specific ship is within communication range, 3
or not.
nel becomes clear.
q Polling
4
--DSC Menu--
Position Reply 5
6
w Acknowledge
Push to Transmit 7
Coast Station
8
Your ship
Push TX
Position Reply
9
To transmit a “Polling Reply”— Quick ACK: 10
Transmitting ➥ After a Polling Request call is received, push [CLR] to
stop the alarm, then rotate [SELECTOR] to indicate the
11
received message log. And then, push [ENT]. (Go to step 12
r at p. 68.)
Transmitting 13
i After the Position Reply call has been transmitted, the dis- 14
play automatically returns to the previous
Position condition (before
Reply ☞Continue to the next page
entering the DSC menu.)
15
CH70 BUSY
16
67
6 DSC OPERATION
68
DSC OPERATION 6
69
6 DSC OPERATION
e Push [ENT] to transmit the Medical Transport call. D Transmitting a Neutral Ship call
• Emergency channel (Channel 70) is automatically selected. The Neutral Ship call informs all ships that your ship is a
• If Channel 70 is busy, the transceiver stands by until the chan- neutral (not a participant) in armed conflict. Be sure to send
nel becomes clear. the call BEFORE entering an area of armed conflict.
--DSC Menu--
Medical Transports ou should set the “Neutral Ship Call” item appearance at
Y
DSC Set up menu in advance. (p. 104)
Push TX
Medical Transports
Your ship
Area of armed
Transmitting conflict
Transmitting
r After the Medical Transport call has been transmitted, the
transceiver selects theMedical
traffic channel (specified in step
Transports
w) automatically. CH70 BUSY
25W INT
TAG
When Channel 70 is
34°34.506N busy
123°23.236W
UTC 12:00 CALLING
70
DSC OPERATION 6
1
q Push [MENU] to enter the DSC menu, then rotate [SE- e Push [ENT] to transmit the Neutral Ship call.
• Emergency channel (Channel 70) is automatically selected. 2
LECTOR] to select “Neutral Ship,” push [ENT].
• If Channel 70 is busy, the transceiver stands by until the chan-
• “Neutral Ship” disappears in default.
nel becomes clear.
3
--DSC Menu--
--DSC Menu--
4
Select Item
Rotate
Distress Call
Received Call Log
≤ Neutral Ship Call
5
SELECTOR
Position Request
˘Neutral Ship Call
6
Push to Transmit
Test Call
Set Up ≥ 7
Push
Push TX
8
w Rotate [SELECTOR] to select a desired traffic channel Neutral Ship Call
9
from the list as below, push [ENT].
Rotate --DSC Menu-- Transmitting 10
SELECTOR
Select Traffic CH
16
11
12
Transmitting
Push 13
r A fter the Neutral Ship call has been transmitted, the
transceiver selects the traffic channel (specified in step 14
Neutral Ship Call
01 06 11 16 21 26 62 67 73 78 83 88 w) automatically.
CH70 BUSY
15
02 07 12 17 22 27 63 68 74 79 84
03 08 13 18 23 28 64 69 75 80 85 25W INT 16
04 09 14 19 24 60 65 71 76 81 86 TAG
05 10 15 20 25 61 66 72 77 82 87
When Channel 70 is
34°34.506N busy
123°23.236W
UTC 12:00 CALLING
71
6 DSC OPERATION
Coast Station When “Manual Input” is selected, set the 9-digit indi-
vidual ID you wish to call with the keypad, push [ENT].
Push
--DSC Menu--
Input Address ID
q Push [MENU] to enter the DSC menu, then rotate 123123123
[SELECTOR] to select “Test Call,” push [ENT].
--DSC Menu-- CLR
Select Item Push
Distress Call ≤
Rotate Received Call Log
Position Request
SELECTOR ˘Test Call
Set Up
Exit
Push
72
DSC OPERATION 6
1
e Push [ENT] to transmit the Test call. t When receiving the acknowledgement call, “Received
• Emergency channel (Channel 70) is automatically selected. Test ACK” appears in the display. See p. 91 for details. 2
• If Channel 70 is busy, the transceiver stands by until the chan-
nel becomes clear. 25W INT 3
--DSC Menu-- 4
Received
Test Call
Test ACK 5
<Station 1
6
Push to Transmit
7
Push TX
8
Test Call
9
Transmitting 10
11
12
Transmitting
13
r After the Test call has been transmitted, the transceiver
automatically returns to the previous
Test Call condition (before en-
14
tering the DSC menu.) 15
CH70 BUSY
16
73
6 DSC OPERATION
--DSC LOG--
Test Call
From Station 1 e The call information appears, push [ENT].
Safety
--DSC Menu--
Test Call Info
From Station 1
Push Safety
74
DSC OPERATION 6
75
6 DSC OPERATION
w Rotate [SELECTOR] to indicate the received message IMPORTANT! Distress call reception should stop after
log information. one sequence since the coast station should send back
• Push [CLR] to ignore the call and exit the condition. an ‘acknowledgement’ to the ship.
e Rotate [SELECTOR] to scroll. If the distress call continues, the coast station may not be
• Push [CLR] to cancel and back to the previous screen. receiving the call. In such cases, you should contact the
• Push [F], then push [8• PRT ] to print out the received mes- ship via the phone.
sage information. When the ship requires a ‘distress relay’ call or the ship
--DSC LOG-- appears not to reply, you should transmit ‘distress relay.’
Rotate Distress Call ≤ (p. 41)
From 121111113
SELECTOR
Undesignated
LAT: 12°23.111N
LON:123°23.123W
UTC:10:25
DIS:1331.6nm
ANG:180.5° ≥
Telephony
Push to Exit
76
DSC OPERATION 6
77
6 DSC OPERATION
78
DSC OPERATION 6
79
6 DSC OPERATION
80
DSC OPERATION 6
81
6 DSC OPERATION
82
DSC OPERATION 6
83
6 DSC OPERATION
TAG Blinks r Push [ENT] to reply the call and change the channel pro-
Received posed by the called station for voice communication.
Able ACK
<Station 1
84
DSC OPERATION 6
85
6 DSC OPERATION
Push to Change CH
Push 25W INT
TAG Blinks
Received r Push [ENT] to change the channel specified by the call-
Group
<Station 1 ing station for listening to an announcement.
86
DSC OPERATION 6
87
6 DSC OPERATION
TAG Blinks
Received
POS Reply r Push [ENT] to return to the normal operation condition.
<Station 1
88
DSC OPERATION 6
89
6 DSC OPERATION
90
DSC OPERATION 6
91
6 DSC OPERATION
n Received messages
The transceiver automatically stores up to 20 distress mes- w Rotate [SELECTOR] to select “Distress.”
sages and 20 other messages. • The received messages are stored in “Distress” in DSC menu if
The stored messages are automatically deleted after 48 its category or format specifier is ‘Distress.’
hours has passed from storing. Rotate --DSC Menu--
The messages can be used as an assistance to the logbook. Select Message
˘Distress
• “ ” indicator blinks when the unread message is stored in the SELECTOR
Others
Call Log memory during normal operation condition.
Push
D Distress message
q Push [MENU] to enter the DSC menu, then rotate
[SELECTOR] to select “Received Call Log,” push e Rotate [SELECTOR] to select the desired message, push
[ENT]. [ENT].
• Or, push [F], then push [9• LOG ] to indicate “Select Message” • Messages which are blinking have not been read yet.
screen as step w. The unread message blinks.
--DSC Menu-- --DSC Menu--
Select Item Select Message
Individual Call ≤ Rotate Distress ACK ≤
Rotate Group Call Distress
Distress Call SELECTOR ˘ Distress Call
SELECTOR ˘Received Call Log Distress Relay ≥
Position Request
Test Call ≥ Push
Push
92
DSC OPERATION 6
1
2
r Rotate [SELECTOR] to scroll the selected message. In case of the Distress Acknowledgement call
• The stored message has various information depending on the
--DSC MENU--
3
type of Distress call.
• Push [ENT] to select the channel 16.
Rotate Distress ACK ≤ 4
• Push [CLR] to cancel and back to the previous screen. From Coast St.1
• Push [CE] to delete the displayed log and returns to “Select
SELECTOR
Distress ID 5
121111113
Message” screen. Undesignated 6
• Push [F], then push [8• PRT ] to print out the received mes- LAT: 12°23.111N
sage information. LON:123°23.123W 7
UTC:10:25 ≥
DIS:1331.6nm
8
In case of the Distress call ANG:180.5°
Telephony 9
--DSC MENU--
Rotate Distress Call ≤ Push to Change CH 10
From 121111113
SELECTOR
Undesignated 11
LAT: 12°23.111N
LON:123°23.123W 12
UTC:10:25
DIS:1331.6nm 13
ANG:180.5° ≥
Telephony
14
Push to Change CH
15
16
93
6 DSC OPERATION
In case of the Distress Cancel In case of the Distress Relay Acknowledgement call
--DSC MENU-- --DSC MENU--
Rotate Distress Cancel ≤
Rotate Distress Relay ACK ≤
From 121111113 To Individual
SELECTOR SELECTOR
Distress ID From Station 2
121111113 Distress ID
Undesignated 121111113
LAT: 12°23.111N Undesignated
LON:123°23.123W LAT: 12°23.111N
UTC:10:25 ≥ LON:123°23.123W ≥
DIS:1331.6nm UTC:10:25
ANG:180.5° DIS:1331.6nm
Telephony ANG:180.5°
Telephony
Push to Change CH
Push to Change CH
Push to Change CH
94
DSC OPERATION 6
D Other messages 1
q Push [MENU] to enter the DSC menu, then rotate e Rotate [SELECTOR] to scroll to the desired message,
[SELECTOR] to select “Received Call Log,” push push [ENT]. 2
[ENT]. • Messages which are blinking have not read yet. 3
• Or, push [F], then push [9• LOG ] to indicate “Select Message” Rotate --DSC Menu--
screen as step w. Select Message 4
˘ Individual Call ≤
5
SELECTOR
--DSC Menu-- All Ships Call
Select Item Position Reply
Rotate
Individual Call ≤ Group Call ≥ Push 6
Group Call
Distress Call
˘Received Call Log
7
SELECTOR
Position Request
Test Call ≥
The unread message blinks. 8
Push
r Rotate [SELECTOR] to scroll the message. 9
• The stored message has various information depending on the
w Rotate [SELECTOR] to select “Others.” 10
type of DSC call.
• Push [CLR] to cancel and back to the previous screen.
Rotate
--DSC Menu--
Select Message • Push [CE] to delete the displayed log and returns to “Select
11
SELECTOR
Distress
˘Others
Message” screen. 12
• Push [F], then push [8• PRT ] to print out the received mes-
sage information. 13
Push
In case of the Individual call 14
--DSC MENU-- 15
Rotate Individual Call ≤ 16
From Station 1
SELECTOR
Routine
Telephony
CH08
In case of the Individual Acknowledgement call In case of the All Ships call
‘Able to Comply’ --DSC MENU--
--DSC MENU-- Rotate All Ships Call ≤
Rotate Individual ACK ≤ From Station 1
SELECTOR
From Station 1 Safety
SELECTOR
Routine Telephony
Telephony CH16
CH08
Able to Comply Push to Change CH
≥
Push to Change CH≥
Push to Exit ≥
• Push [ENT] to change the channel,
specified by the calling station.
96
DSC OPERATION 6
In case of the Position Request call In case of the Polling Request call 1
--DSC MENU-- --DSC MENU-- 2
Position Request Polling Request
From Station 1 From Station 1 3
Safety Routine
4
5
• Push [ENT] to reply the call. (p. 64) • Push [ENT] to reply the call. (p. 67) 6
7
In case of the Position Reply call In case of the Test call 8
Rotate
--DSC MENU-- --DSC MENU--
Test Call
9
Position Reply ≤
SELECTOR
From Station 1 From Station 1
Safety
10
Safety
LAT: 12°23.111N
LON:123°23.123W
11
UTC:10:25
DIS:1331.6nm
12
ANG:180.5° ≥
• Push [ENT] to reply the call. (p. 74) 13
Push to Exit
14
• Push [ENT] to exit the condition.
15
16
97
6 DSC OPERATION
--DSC MENU--
Test ACK
From Station 1
Safety
Push to Exit
Push to Delete
98
DSC OPERATION 6
Rotate
Add:Group ID
DEL:Individual ID
≤ 5
D Printing out the DSC memory contents DEL:Group ID
6
The automatic print out capability when a DSC call is re- SELECTOR ˘Auto Print
ceived is available.
Position Auto ACK
DSC Data Output ≥ 7
The received DSC call contents can be printed out when a Push
printer (IBM® centronics or compatible) is connected to the
8
e Rotate [SELECTOR] to select the automatic print out
transceiver. (p. 109)
function ON or OFF.
9
q Push [MENU] to enter the DSC menu, then rotate --DSC Menu-- 10
[SELECTOR] to select “Set up,” push [ENT]. Auto Print
ON 11
˘OFF
--DSC Menu--
Select Item
12
Distress Call
Received Call Log
≤ 13
Rotate Position Request
Test Call 14
r Push [ENT] to set and return to the DSC Set up menu.
SELECTOR ˘Set up
Exit • Push [CLR] to cancel and back to the previous screen.
15
Push t Rotate [SELECTOR] to select “Exit,” push [ENT] to re- 16
turn to DSC menu.
• Pushing [CLR] also returns to DSC menu.
y Repeat again to return to the normal operation condition.
99
6 DSC OPERATION
Push
100
DSC OPERATION 6
101
6 DSC OPERATION
Push
r Push [ENT] to set and return to the DSC Set up menu.
w Rotate [SELECTOR] to select “CH70 SQL Level,” • Push [CLR] to cancel and back to the previous screen.
push [ENT]. t Rotate [SELECTOR] to select “Exit,” push [ENT] to re-
--DSC Menu-- turn to DSC menu.
Set Up • Pushing [CLR] also returns to DSC menu.
Auto Print ≤
Rotate Position Auto ACK y Repeat again to return to the normal operation condition.
DSC Data Output
SELECTOR ˘CH70 SQL Level
Medical Transports
Neutral Ship Call ≥
Push
102
DSC OPERATION 6
103
6 DSC OPERATION
104
DSC OPERATION 6
105
7 SET MODE
--Set Mode--
Rotate ˘Scan Type
Scan Timer
SELECTOR Beep
Internal Speaker
Display Contrast
MIC
Cursor Movement ≥
Exit
106
SET MODE 7
(Default: OFF)
107
7 SET MODE
➔
This item adjusts the contrast of the LCD in 8 steps. You can select the direction of [SELECTOR] rotation from
--Set Mode--
CW (clockwise) or CCW (counter-clockwise) to move the
Rotate cursor downward.
Display Contrast
SELECTOR
˘5 ≤ Turn Selector CW : Rotate [SELECTOR] clockwise for the
4
3 cursor downward.
8 2 ≥ • R otate [SELECTOR] counter-clockwise
7
6 for the cursor upward.
˘5 Turn Selector CCW : R otate [SELECTOR] counter-clock-
4 (Default: 5) wise for the cursor downward.
3
2 • R otate [SELECTOR] clockwise for the
1 cursor upward.
--Set Mode--
Rotate MIC
˘Hand MIC
SELECTOR Handset
(Default: Turn Selector CCW)
108
CONNECTIONS AND MAINTENANCE 8
n Connections 1
2
q t VDR/CLONE CONNECTORS
Connects a voice recorder. 3
NC NC 4
w VDR (+) ICF
GND NC NC 5
GND VDR (–)
6
Transceiver’s rear panel view
7
u y GPS RECEIVER/EXTERNAL SPEAKER CONNECTOR
y t r e 8
➥ Connects a GPS receiver to DSC Data IN (−)/(+) for
q ANTENNA CONNECTOR
Connects a marine VHF antenna with a PL-259 connec-
position and time indications. 9
• Input level: Less than 2 mA (when 2 V applied; as a listener)
tor to the transceiver. • A
n IEC61162-1: 2000 (sentence formatters RMC, GGA, 10
CAUTION: Transmitting without an antenna will dam- GNS, GLL) compatible GPS receiver is required. Ask your
age the transceiver. dealer about suitable GPS receivers.
11
w ANTENNA CONNECTOR (for receiving on Channel 70) DSC Data OUT (+) SP (+) 12
DSC Data OUT (–) SP (–)
Connects a marine VHF antenna with a PL-259 connec- 13
tor to the transceiver. DSC Data IN (–) DSC Data IN (+)
Transceiver’s rear panel view 14
e D-SUB 25-PIN (for a printer connection)
Connects a printer (IBM® centronics or compatible) to the ➥ Connects a navigation equipment. 15
• Output level: 40 mA max. (as a talker)
transceiver.
• IEC61162-1: 2000 (sentence formatters DSC, DSE) compat-
16
r HANDSET CONNECTOR ible for plotting received other ships position data.
Connect the optional handset only. ➥ Connects an external speaker.
CAUTION: NEVER connect the optional hand microphone • Lead: Thicker than 0.75 sq mm, Length: Shorter than 1.5 m
here. They may cause damage to the transceiver. are recommended.
109
8 CONNECTIONS AND MAINTENANCE
u DC POWER CONNECTOR
Connects the PS-250 with the supplied DC power cable.
n Antenna
(p. 112)
A key element in the performance of any communication
CAUTION: system is an antenna. Ask your dealer about antennas and
• I C-GM651 should be connected to the DC power the best place to mount them.
supply through the PS-250, sold by the set with the
IC-GM651, when it is operated.
• After connecting the DC power cable, cover the con- n Fuse replacement
nectors with a rubber vulcanizing tape as shown
below, to prevent water seeping into the transceiver. One fuse is installed in the supplied DC power cable. If a
fuse blows or the transceiver stops functioning, track down
Rubber vulcanizing the source of the problem, if possible, and replace the dam-
tape aged fuse with a new, rated one.
Fuse rating: 10 A
110
CONNECTIONS AND MAINTENANCE 8
n Supplied accessories 1
2
The following accessories are supplied. D Accessory connectors set up
The accessory connectors are used for the accessory cable 3
Mounting bracket For mounting bracket connection to the connectors t and y as at left.
Knob bolts Flat washers (M5)
4
6-pin ➪ y 8-pin ➪ t
5
1
Screws (5×20) Spring washers (M5)
*1 *1 6
*2 ACC Cable ACC Cable
2 7
DC power cable Sponges Accessory connectors 8
3
Solder Solder 9
6 pin 8 pin 4 10
*1 Be sure to set these rings to keep the waterproof capability. 11
*2 Select either larger or smaller one to suit to the cable diameter.
12
13
14
15
16
111
8 CONNECTIONS AND MAINTENANCE
GND
Before connecting the DC power cable, make sure the
power is OFF, and the DC power cable polarity is correct.
PS-250
• Red : positive + terminal
• Black : negative − terminal
The PS-250 dc-dc power supply, sold by the set with the
DC power cable
IC-GM651, converts the input voltage (10.8 to 31.2 V DC) (Supplied with DC power cable
from the DC power supply, then provides 12.5 V DC, 5.3 A of the PS-250) (Supplied with
the continuous power to the transceiver. the IC-GM651)
12 V or 24 V
The optional PS-240 ac-dc power supply converts the input battery
voltage (85.0 to 264.0 V AC: 47 to 63 Hz; nominal operating
frequency 50 Hz) from the AC outlet, then provides 14.5 V
DC, 7 A of the continuous power to the PS-250.
Terminal guard
112
CONNECTIONS AND MAINTENANCE 8
1
2
D Connecting to the AC outlet through the PS-250 AUTION: NEVER short the DC power terminals of the
C
and optional PS-240 PS-250/PS-240 when connecting a DC power cable. Oth- 3
IC-GM651 erwise there is danger of electric shock and/or equipment 4
damage.
GND
5
DC power cable
(Purchase PS-250 6
separately)
7
PS-240
8
GND
9
DC power cable
GND
(Supplied with DC power cable 10
the PS-250) (Supplied with
the IC-GM651) 11
12
12 V or 24 V 13
battery
AC power cable 14
(Supplied with Terminal guard
the PS-240) 15
Keep the terminal guard
To AC outlet
attached after connect- 16
ing cables.
114
CONNECTIONS AND MAINTENANCE 8
n MB-75 installation 1
2
An optional MB-75 flush mount kit is available for mounting r Attach the clamps on either side of the IC-GM651.
the transceiver to a flat surface such as an instrument panel. • Make sure that the clamps align parallel to the IC-GM651’s body. 3
AUTION: KEEP the transceiver and microphone at least
C
4
1 meter away from your vessel’s magnetic navigation 5
compass.
6
Supplied bolt
q U sing the attached template, carefully cut a hole into 7
the instrument panel (or wherever you plan to mount the
transceiver). 8
w Slide the transceiver through the hole as shown below. Clamp 9
10
t Tighten the end bolts on the clamps (rotate clockwise) so
that the clamps press firmly against the inside of the in- 11
strument control panel. 12
y Tighten the locking nuts (rotate counterclockwise) so that
the IC-GM651 is securely mounted in position as below. 13
End bolt 14
y 15
16
Locking nut
t
e Attach the 2 supplied bolts (M5 × 8 mm) on either side of
the IC-GM651.
u Connect the antenna and power cable, then return the
instrument control panel to its original place.
115
8 CONNECTIONS AND MAINTENANCE
n Microphone (HM-126RB)
q D Connection
Insert the connector cable into the mic connector ([MIC]) on
Microphone
the front panel, and tighten the cable nut as shown below.
Speaker
AUTION: NEVER connect the optional handset (HS-98)
C
here.
w e
[MIC]
116
CONNECTIONS AND MAINTENANCE 8
n Handset (HS-98) 1
2
Cradle w HANDSET CONNECTOR
q Insert the connector cable into the handset connector 3
([HAND SET]) on the rear panel, and tighten the cable
nut as shown below.
4
5
e PTT SWITCH [PTT]
Push and hold to transmit; release to receive.
6
7
w D Connection 8
Insert the connector cable into the handset connector
Handset
([HAND SET]) on the rear panel, and tighten the cable nut 9
as shown below.
10
e AUTION: NEVER connect the optional hand micro-
C
phone (HM-126RB) here. 11
q SPEAKER SWITCH
Toggle the connected external speaker output ON and 12
OFF when pick the handset up. 13
• When the switch is set to “ ” position
- Emits the receiving audio from the connected external 14
speaker.
[HAND SET]
15
• When the switch is set to “ ” position
- Mutes the connected external speaker output. 16
• The receiving audio can be heard from the earpiece
of the handset.
- Replace the handset into the cradle to emits the re-
ceiving audio from the connected external speaker.
117
9 TROUBLESHOOTING
118
SPECIFICATIONS AND OPTIONS 10
n Specifications 1
2
D General D Transmitter
• Frequency coverage : TX 156.000–161.450 MHz • RF output power : 25 W and 1 W 3
RX 156.000–163.425 MHz • Modulation system : Variable reactance frequency
• Mode : FM (16K0G3E), DSC (16K0G2B) modulation 4
• Current drain (at 24 V) : TX high (25 W) 3.5 A • Max. frequency deviation : ±5.0 kHz 5
Max. audio 1A • Spurious emissions : Less than 0.25 µW
• Power supply requirement : 12/24 V DC (10.8 to 31.2 V) • Adjacent channel power : More than 70 dB 6
• Frequency stability : ±5 ppm • Audio harmonic distortion : Less than 10%
• Operating temp. range : –15°C to +55°C (at 1 kHz, 60% deviation) 7
• Antenna impedance : 50 ˘ nominal • Residual modulation : More than 40 dB
• Input impedance (Hand mic) : 2 k˘ • Audio frequency response : +1 to –3 dB of 6 dB/octave
8
• Output impedance (audio) : 4 ˘ range from 300 Hz to 3000 Hz 9
• VDR interface
Impedance : Balanced 600 ˘ D Receiver 10
Ground : Floating
Audio level : TX –4 dBm (typical)
• Receive system : Double conversion superheterodyne 11
• Sensitivity (20 dB SINAD) : –5 dBµ emf (typical)
(at 1 kHz, ±3 kHz deviation) –5 dBµ emf (typical) (CH 70 receiver) 12
RX –3 dBm (typical) • Squelch sensitivity : Less than –2 dBµ emf
(at 1 kHz, ±3 kHz deviation) • Spurious response : More than 73 dB 13
• Dimensions (Projections not included) • Intermodulation : More than 75 dB
IC-GM651 : 220(W) × 110(H) × 109.4(D) mm • Adjacent channel selectivity : More than 75 dB
14
PS-250 : 250(W) × 67(H) × 200(D) mm • Hum and noise : More than 45 dB 15
• Weight • Audio output power : 2.0 W at 10% distortion with a 4 ˘
IC-GM651 : Approx. 1600 g load 16
PS-250 : Approx. 2100 g
* This specification is described when the IC-GM651 is used with
the PS-250.
D Dimensions n Options
• PS-240 ac-dc power supply
Provides stable 14.5 V DC output converted from 85 to 264 V
AC power source.
• HS-98 handset
Provides clear audio reception during offshore conditions
and comes in handy for listening privacy on board.
Unit: mm
120
CHANNEL LIST 11
• International channels 1
Frequency (MHz) Frequency (MHz) Frequency (MHz) Frequency (MHz) Frequency (MHz) Frequency (MHz)
CH
Transmit Receive
CH
Transmit Receive
CH
Transmit Receive
CH
Transmit Receive
CH
Transmit Receive
CH
Transmit Receive 2
01 156.050 160.650 11 156.550 156.550 21 157.050 161.650 62 156.125 160.725 72 156.625 156.625 82 157.125 161.725 3
02 156.100 160.700 12 156.600 156.600 22 157.100 161.700 63 156.175 160.775 73 156.675 156.675 83 157.175 161.775
03 156.150 160.750 13 156.650 156.650 23 157.150 161.750 64 156.225 160.825 74 156.725 156.725 84 157.225 161.825 4
04 156.200 160.800 14 156.700 156.700 24 157.200 161.800 65 156.275 160.875 75*3 156.775 156.775 85 157.275 161.875
5
05 156.250 160.850 15*2 156.750 156.750 25 157.250 161.850 66 156.325 160.925 76*3 156.825 156.825 86 157.325 161.925
06 156.300 156.300 16 156.800 156.800 26 157.300 161.900 67 156.375 156.375 77 156.875 156.875 87 157.375 157.375 6
07 156.350 160.950 17*2 156.850 156.850 27 157.350 161.950 68 156.425 156.425 78 156.925 161.525 88 157.425 157.425
7
08 156.400 156.400 18 156.900 161.500 28 157.400 162.000 69 156.475 156.475 79 156.975 161.575
09 156.450 156.450 19 156.950 161.550 60 156.025 160.625 70*1 156.525 156.525 80 157.025 161.625 8
10 156.500 156.500 20 157.000 161.600 61 156.075 160.675 71 156.575 156.575 81 157.075 161.675
9
*1 DSC operation only.
10
*2 Channels 15 and 17 may also be used for on-board communications provided the effective radiated power does not exceed 1 W,
and subject to the national regulations of the administration concerned when these channels are used in its territorial waters. 11
*3 1 W only. 12
The use of these channels should be restricted to navigation-related communications only and all precautions should be taken to
avoid harmful interference to channel 16, e.g. by limiting the output power to 1 W or by means of geographical separation. 13
14
15
16
121
MEMO
MEMO
A6630H-1EX-qa
Printed in Japan
© 2008–2017 Icom Inc.
Printed on recycled paper with soy ink. 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan