Professional Documents
Culture Documents
Conplast SP430 0407
Conplast SP430 0407
$SULO
+LJKSHUIRUPDQFHVXSHUSODVWLFLVLQJ 7HFKQLFDOVXSSRUW
DGPL[WXUH
Fosroc provides a technical advisory service for on-site
8VHV assistance and advice on admixture selection, evaluation
trials and dispensing equipment. Technical data and
To provide excellent acceleration of strength gain at guidance can be provided for admixtures and other
early ages and major increases in strength at all ages products for use with fresh and hardened concrete.
by significantly reducing water demand in a concrete
mix. 7\SLFDOGRVDJH
Particularly suitable for precast concrete and other
high early strength requirements. The optimum dosage of Conplast SP430 to meet specific
To significantly improve the workability of site mixed requirements should always be determined by trials
and precast concrete without increasing water de- using the materials and conditions that will be
mand. experienced in use. This allows the optimisation of
admixture dosage and mix design and provides a
To provide improved durability by increasing ultimate
strengths and reducing concrete permeability. complete assessment of the concrete mix. Starting points
for such trials, based on the primary use of the product,
In screeds it reduces the water content required to give are to use a dosage within the normal typical ranges.
suitable workability for placing and compaction.
For high strength, water reduced concrete the normal
$GYDQWDJHV dosage range is from 0.70 to 2.00 litres/100 kg of
cementitious material, including PFA, GGBFS and
Major increases in strength at early ages without microsilica. For high workability concrete the normal
increased cement contents are of particular benefit in dosage range is from 0.70 to 1.30 litres/100 kg of
precast concrete, allowing earlier stripping times. cementitious material.
Makes possible major reductions in water:cement
ratio which allow the production of high strength Where a combination of performance is required, such as
concrete without excessive cement contents. some increase in workability combined with a reduced
Use in production of flowing concrete permits easier water content, then the whole range of dosages from 0.70 to
construction with quicker placing and compaction and 2.00 litres/100 kg of cementitious material can be
reduced labour costs without increasing water content. considered.
Increased workability levels are maintained for longer Use at other dosages
than with ordinary sulphonated melamine admixtures.
Improved cohesion and particle dispersion minimises Dosages outside the typical ranges quoted above may be
segregation and bleeding and improves pumpability. used if necessary and suitable to meet particular mix
Chloride free, safe for use in prestressed and rein- requirements, provided that adequate supervision is
forced concrete. available. Compliance with requirements must be as-
In screed material, the lower water content leads to sessed through trial mixes. Contact the Fosroc Customer
quicker drying times Service Department for advice in these cases.
6WDQGDUGVFRPSOLDQFH 3URSHUWLHV
Conplast SP430 complies with BS 5075 Part 3 and with Appearance: Brown liquid
ASTM C494 as Type A and Type F. Specific gravity: Typically 1.20 at 20°C
Chloride content: Nil to BS 5075
'HVFULSWLRQ Air entrainment: Typically less than 2% additional air is
entrained at normal dosages.
Conplast SP430 is a chloride free, superplasticising
Alkali content: Typically less than 72.0 g. Na2O
admixture based on selected sulphonated napthalene
equivalent/litre of admixture. A fact
polymers. It is supplied as a brown solution which
sheet on this subject is available.
instantly disperses in water.
Page 1
$SULO
&RQSODVW 63
,QVWUXFWLRQVIRUXVH (IIHFWVRIRYHUGRVLQJ
constructive solutions
Page 2
$SULO
&RQSODVW 63
([DPSOH/DERUDWRU\WHVWLQJIRUZDWHUUHGXFWLRQDQGZRUNDELOLW\LQFUHDVHJUDYHODJJUHJDWHV
([DPSOH/DERUDWRU\WHVWLQJZLWKPLFURVLOLFDDGGLWLRQDQGJUDYHODJJUHJDWHV
/LPLWDWLRQV
81SDFNDJLQJUHJXODWLRQV
If alkali reactive aggregate must be used Conplast SP430
may contribute an undesirable level of alkali to the mix. To comply with current regulations, all products of a
Contact the Customer Service Department for advice in hazardous nature that are involved in a sea crossing as
these situations. part of the delivery requirements must be packed in
United Nations Approved receptacles.
(VWLPDWLQJ²SDFNDJLQJ When a known sea crossing is involved, whether local to
the United Kingdom or for export worldwide, Fosroc will
Conplast SP430 is available in 20 litre drums or bulk supply in the correct UN packaging. Where Fosroc are
supply. For larger users, storage tanks can be supplied. only requested to deliver within the United Kingdom
Details of specific packaging volumes are available on mainland, but the purchaser intends to ship on, it is
request. incumbent on the purchaser to specify that UN packaging
is required at the time of placing the order. Otherwise,
once delivery is received, the responsibility is that of the
purchaser.
&RQSODVW 63
6WRUDJH
3UHFDXWLRQV
+HDOWKDQGVDIHW\
)LUH
$GGLWLRQDOLQIRUPDWLRQ
Important note
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions for the
Supply of Goods and Services, copies of which may be obtained on request. Whilst Fosroc endeavours to ensure that any advice,
recommendation, specification of information it may give is accurate and correct, it cannot, because it has no direct or continuous control
over where or how its products are applied, accept any liability either directly or indirectly arising from the use of its products, whether or
not in accordance with any advice, specification, recommendation of information given by it.
)RVURF/LPLWHG
Drayton Manor Business Park
Coleshill Road, Tamworth, telephone:
constructive
constructive solutions
solutions fax: email:
Staffordshire B78 3TL. UK Aydinevler Mah.+44 (0) 1827 262444Telephone: uk@fosroc.com E-mail:
+44 (0) 1827 262222
Fosroc Idea Sanayi Cad. Demirtas Plaza +90 216 463 69 63 enquiryturkey@fosroc.com
ZZZIRVURFFRP
Construction Certificate number FM 610
No: 13 D: 7-8, 34854, Fax:
Chemicals Co. Maltepe – Istanbul Page
/ TURKEY
4 +90 216 463 67 76 www.fosroc.com