Professional Documents
Culture Documents
PSMZ100 200
PSMZ100 200
PSMZ100 200
Advanced Multi-Zone
climate control system- 24Vac and
can control up to 4 or 7 zones
General Features
• Main Input - 24Vac
The PS-MZ 100/200 is ideal for
• Controls up to 4 zones (PS-MZ100) or 7 zones (PS-
residential, commercial or industrial MZ200)
applications. It is compatible with • Zone 1 also serves as Master (same thermostat)
Heat/Cool or Heat Pump HVac • Selectable system configuration- Heat/Cool or Heat pump
applications and can control up to 4 • Up to 5 stages of Heat and 5 stages of Cool
• Selectable Heat output- Electric or Oil/Gas (jumper
(PS-MZ100) or 7 (PS-MZ200) different
selectable)
zones. • Modes: Cool, Heat, Auto-change Over, Fan Only-
One of the zone serves also as the selectable through Master ONLY
master, and different types of • T1- Indoor temperature sensor- option (for Fresh Air
Damper)
thermostats can be selected as zones.
• T2- Outdoor temperature sensor- option (for Fresh Air
Zones can also be programmed for Damper)
ON/OFF, ideal for times when the zone • T3- Indoor Coil sensor (freeze protection in Cool and
is less occupied. overheat protection in Heat)
• Output for dampers- On/Off, 3-wire, 24Vac
The main board offers inputs for • Zone dampers- On/Off, 3-wire
Bypass and Fresh Air dampers, and 3 • Fresh Air Dampers- 2 logics for open/close:
different temperature sensors. 1. by timer (min per hour) OR
2. by temperature difference (T1-T2)
Other features such as Auto-
• Bypass Damper (On/Off, 3-wire) output
Changeover mode and quick • Display temperature available in C or F- depending on
connectors from the thermostats to the model ordered
main board, make this multi-zone the • Economy mode (Unoccupied mode)
simplest and most efficient climate • Zone thermostats with weekly program- option depending
on model ordered
control system.
• Weekly Program type- (5-1-1)- 4 times Set Cool/Set Heat
Zone Z100
General Features
• Set local On/Off status
• Set local set point
• Weekly program- option
(depending on thermostat ordered)
Prog Non-Prog
Cable Connection
The connection between the
main board and the thermostat
is made by telephone jack as
shown, and the necessary cable
Tel. Cable Main Board Zone
is shown here.
Electrical Diagram
*Zone
To AC System Controllers-
Telephone
Jacks
Heat Pump in
Heat Pump in
Compressor 1
Compressor 2
Master &
Main Input- Indoor Outdoor Indoor Coil
Zone 1
Zone 4
Zone 3
Heat 1
Zone 2
Heat 2
Heat
Cool
24Vac Sensor- Sensor- Sensor-
Fan
option option option
Y1 Y2 W1 W2 B O G Rc Rh C T1 T1 T2 T2 T3 T3
24Vac-
Fresh Air Zone 1 Zone 2 Fresh Air Zone 4
power for Bypass Damper Damper Damper Damper Damper
dampers and damper
zone
controller *Note: PS-MZ200 offers up to 7 zones
Components
Master & Zone 1 ETN-M100-F Master & Zone controller, wall-mount, display in °F
(1 required per system) ETN-M100-Prog-C Master & Zone controller with 5-1-1 program, wall-mount, display in °C
ETN-M100-Prog-F Master & Zone controller with 5-1-1 program, wall-mount, display in °F
Note: All Master and Zone thermostats are available in flush-mount models (FMT) as well.