Professional Documents
Culture Documents
Instruction eWON Router Certificate Update PDF
Instruction eWON Router Certificate Update PDF
Instruction eWON Router Certificate Update PDF
Balancing and
Diagnostic Systems
Schenck RoTec GmbH • Landwehrstraße 55 • D-64293 Darmstadt
Schenck RoTec GmbH
Landwehrstraße 55
64293 Darmstadt
Germany
Your Ref.
Your Message
Our Ref. .
Contact Marina Pandzic
eMail Service.Rotec@schenck.net
Date 08.11.2018
DE AEOC 105616
Managing Directors:
Jörg Brunke (Chairman)
Susanne Schlegel
Registered Office:
Darmstadt
District Court Darmstadt
HRB 1732
VAT ID no.: DE 811 113 684
Banks:
Deutsche Bank AG, Darmstadt
Account: 0 111 260
Bank code: 508 700 05
IBAN: DE95508700050011126000
SWIFT: DEUTDEFF508
Commerzbank Darmstadt
Account: 13 83132
Bank code: 508 400 05
IBAN: DE54508400050138313200
SWIFT: COBADEFF508
Balancing and
Diagnostic Systems
Current problem:
Risk:
Solution:
2
Balancing and
Diagnostic Systems
The router is installed inside the cabinet. Please look for such a device:
3
Balancing and
Diagnostic Systems
- In case USER is blinking further steps are required - using the GUI (proceed 1.2)
4
Balancing and
Diagnostic Systems
This router is available in 2 options. Therefore please choose your desired way to get the
router connected. The 3G router (eWON 2005CD/HSUPA) allows you to setup the
communication via WAN or 3G. The WAN router (eWON 2005CD) requires WAN
connection (company network with internet access (no proxy server supported).
- Check if the WAN connector (see above in red) is connected to a network with
Internet access. If there is no cable connected to the WAN connector, please
supply a temporary Internet connection (check with your local IT for options).
- Open Internet Explorer and navigate to IP: 10.10.0.1
- Insert username "Schenck" and as password the commissioning number of the
machine, e.g. ftk1234
- Select "Configuration"
5
Balancing and
Diagnostic Systems
- Select "Communication"
6
Balancing and
Diagnostic Systems
- Select "Configuration"
7
Balancing and
Diagnostic Systems
- Select "Communication"
- Change parameter "GSM Pin Code" according to your SIM card PIN
8
Balancing and
Diagnostic Systems
- After all required changes are done, press "Update". After getting the message
"The modem config has been correctly updated." Turn off router and install the
new SIM card
- Then open this page again and check if the network is shown correctly. The
"Signal level" indicates the quality of the GSM network. If the "Operator" and
"Network" are now shown correctly, the SIM cards PIN will be correct.
9
Balancing and
Diagnostic Systems
10
Balancing and
Diagnostic Systems
- If you got the information "SUCCESS: Internet connection tested" everything is fine.
Maybe the last step requires several minutes to update the certificates
11
Balancing and
Diagnostic Systems
12
Balancing and
Diagnostic Systems
This router is available in 3 options. Therefore please choose your desired way to get the
router connected:
- WAN router
- WAN router with 3G interface
- WAN router with WiFi module (802.11b/g)
-Choose Internet interface to " Ethernet INTERNET connection" and press "Next"
13
Balancing and
Diagnostic Systems
- Select DHCP or use setting for static IP address . Then press "Next"
14
Balancing and
Diagnostic Systems
15
Balancing and
Diagnostic Systems
16
Balancing and
Diagnostic Systems
3. General
In case you have problems with getting the router online, you can send your router to the
following address:
17