Professional Documents
Culture Documents
Abs 0114
Abs 0114
Issue 6
Page 1 of 11
January 2015
Aerospace series
Bolt – Hexagon Head, Close Tolerance
6AL-4V Titanium Alloy
When this standard is applied, a careful check must be made as to whether any protective rights exist. This
standard issuer hereby disclaims any liability for infringement of patent or design rights resulting from the use of
this standard.
Copyright reserved
Ref. no. ABS0114
ABS0114 Page 2
Issue 6
Contents
1 Scope
2 Normative references
3 Requirements
4 Designation
5 Marking
6 Technical specification
7 Example of installation
ABS0114 Page 3
Issue 6
1 Scope
This standard specifies the dimensions, required characteristics and mass of a hex, bolt head for use in aerospace
applications.
2 Normative References
AMS 4928 Titanium Alloy Bars, Wire, forgings , and Rings 6Al – 4V Annealed (UNS R56400)
AMS 4967 Titanium Alloy Bars, Wire, forgings , and Rings 6.0Al – 4.0V Annealed, Heat Treatable
(UNS R56400)
MIL-DTL-83488 Coating, Aluminium, Ion Vapour Deposition
AS8879 Screw threads, controlled radius root with increased minor diameter.
NAS 4004 Fasteners, 6AL-4V Titanium alloy, externally threaded, 160 KSI Ftu, 95 KSI Ftu, 450
degrees F.
ASME B46.1 Surface texture (surface roughness, waviness, and lay.)
EN6118 Process specification – Aluminium base protection for fasteners
EN6117 Specification for lubrication of bolts with cetyl alcohol
ISO 8080 Aerospace – Anodic treatment of titanium and titanium alloys - Sulfuric acid process
3 Required Characteristics
3.2 Material
Shall be in accordance with table 2
ØN ØD
W ØE ØTD
R RAD
DRILL HOLE DIA.‘P’ WHEN
SPECIFIED BY CODE ‘D’ IN THE
15º PART NUMBER CALL UP.
CHAMFER OPTIONAL CSK
DRILL K (3 HOLES) WITHIN .010 (0.25) OF OPTIONAL.
CENTRE OF HEX. FLAT WHEN SPECIFIED BY O
PART NUMBER. LOCKWIRE HOLES MUST BE CHAMFER 15
FREE FROM BURRS AND SHARP EDGES. TO E OPTIONAL
Figure 1: Configuration
ABS0114 Page 5
Issue 6
Dia Thread C ØD E
Dash Size Dia
No UNJF – 3A Min
Max Min Max Min
.376 .367 .1895 .1885 .335
3 .1900 – 32
(9,550) (9,322) (4,813) (4,788) (8,509)
.439 .429 .2495 .2485 .398
4 .2500 - 28
(11,151) (10,897) (6,337) (6,312) (10,109)
.502 .492 .3120 .3110 .460
5 .3125 - 24 (12,751) (12,497) (7,925) (7,899) (11,684)
.564 .554 .3745 .3735 .523
6 .3750 - 24
(14,326) (14,072) (9,512) (9,487) (13,284)
.690 .678 .4370 .4360 .648
7 .4375 - 20
(17,526) (17,221) (11,100) (11,074) (16,459)
.752 .741 .4995 .4985 .710
8 .5000 - 20 (19,101) (18,821) (12,687) (12,662) (18,034)
.877 .865 .5615 .5605 .835
9 .5625 - 18
(22,276) (21,971) (14,262) (14,237) (21,209)
.940 .928 .6240 .6230 .898
10 .6250 - 18
(23,876) (23,571) (15,850) (15,824) (22,809)
1.065 1.052 .7490 .7480 1.023
12 .7500 - 16 (27,051) (26,721) (19,025) (18,999) (25,984)
Call up
Material Protection Lubrication Colour Identification
Code
Aluminium coating
Titanium Blue Dye on Bolt end
- To MIL-DTL-83488 None
and Chamfer
6AL-4V Alloy Type II Class 3
per Aluminium coating as
V As per EN6117 Yellow All Over
AMS4928 or per EN6118
AMS4967 Sulfuric-acid anodizing
T As per EN6117 Blue All Over
as per ISO 8080
Mass:
CALCULATION OF THE MASS OF A BOLT
EXAMPLE:
BOLT ABS0114-3-1
Invariable mass : 1.063+0.661= 1.724
Variable mass : 0.128 x 1 (length Code) = 0.128
Total mass : 1.852 g
Table 4: Mass
Fixed Mass (g) Variable Mass (g)
Dia Code
Head Mass Thread Mass Smooth part Mass
3 1.063 0.661 0.128
4 1.636 1.313 0.222
5 2.631 2.431 0.347
6 3.977 3.630 0.500
7 6.883 5.749 0.681
8 9.283 7.511 0.889
9 14.149 10.678 1.124
10 17.989 13.898 1.388
12 27.586 21.303 2.000
ABS0114 Page 8
Issue 6
4 Designation
This type of standard shall be designated according to the philosophy of the following example:
5 Technical specification
NAS 4004 Except for protective treatment and lubrication
ABS0114 Page 9
Issue 6
.0156”(0,396mm) and .0312” (0,792mm) oversize shank for replacement of bolts shown on Page 3.
ØD
Grip Length
Thread
Size ØD ØD
UNJF – 3A Part Number After Part Number After
Coating Coating
.2026 .2182
(5,146) (5,542)
.1900-32 ABS 0114 – 3 - **X ABS 0114 – 3 - **Y
.2016 .2172
(5,121) (5,517)
.2651 .2807
(6,734) (7,130)
.2500-28 ABS 0114 – 4 - **X ABS 0114 – 4 - **Y
.2641 .2797
(6,708) (7,104)
.3276 .3432
(8,321) (8,717)
.3125-24 ABS 0114 – 5 - **X ABS 0114 – 5 - **Y
.3266 .3422
(8,296) (8,692)
.3901 .4057
(9,909) (10,305)
.3750-24 ABS 0114 – 6 - **X ABS 0114 – 6 - **Y
.3891 .4047
(9,883) (10,279)
.4526 .4682
(11,496) (11,892)
.4375-20 ABS 0114 – 7 - **X ABS 0114 – 7 - **Y
.4516 .4672
(11,471) (11,867)
.5151 .5307
(13,084) (13,480)
.5000-20 ABS 0114 – 8 - **X ABS 0114 – 8 - **Y
.5141 .5297
(13,058) (13,454)
.5771 .5927
(14,658) (15,055)
.5625-18 ABS 0114 – 9 - **X ABS 0114 – 9 - **Y
.5761 .5917
(14,633) (15,029)
.6396 .6552
(16,246) (16,642)
.6250-18 ABS 0114 – 10 - **X ABS 0114 – 10 -**Y
.6386 .6542
(16,220) (16,617)
.7646 .7802
(19,421) (19,817)
.7500-16 ABS 0114 – 12 - **X ABS 0114 – 12 - **Y
.7636 .7792
(19,396) (19,792)
ABS0114 Page 11
Issue 6
RECORD OF REVISIONS
Clause
Issue Description of modification
modified
6
Corrected Designation table for size code to indicate “(see table 1)”
01/15