Professional Documents
Culture Documents
Zelio Control - Measurement and Control Relays: Presentation, Description
Zelio Control - Measurement and Control Relays: Presentation, Description
Zelio Control - Measurement and Control Relays: Presentation, Description
Presentation
RM22 Zelio multifunction control relays monitor the following functions on 3-phase
1 supplies:
Functions RM22TA RM22TU RM22TR RM22TG
Sequence of phases L1, L2, and L3
Phase failure with regeneration
Asymmetry
Undervoltage
2 Overvoltage and undervoltage
Function performed
Function not performed
RM22T●●●
Depending on the model RM22T●●● control relays:
b Accept different nominal 3-phase voltages: up to 480 V a
b Monitor their own power supply measured as a true rms value
3 b Are designed for clip-on mounting on DIN rail
They feature:
b Sealable cover to protect the settings
b Diagnostic button for load circuit testing
b Relay output status LED
b Fault detection indication LED
Description
RM22TA RM22TU 1a Voltage range selector switch
10 20 -8 -14
2 3b
-6 -16
5 25 <U
Tt -4 -18
0,1
10
30s
-2 -20%
3a
12
Asym
4 Diagnostic button
Def Def
5 15%
R R
4 DIAGNOSTIC 4 DIAGNOSTIC
12 11 14 12 11 14
22 21 24 22 21 24
8 RM22TR RM22TG
L1 L2 L3 L1 L2 L3
RM22TR31 RM22TG20
200 200
1b
ON DELAY
DELAY
208 208
OFF
9
220 220
240 240
10 20
5 25
Tt
0,1 30s
8 14
3c
6 16
>U
4 18 Un
Def
2 20%
R
-8 -14 R
3b
-6 -16
<U
-4 -18
4
-2
4
-20%
DIAGNOSTIC DIAGNOSTIC
12 11 14 12 11 14
10 22 21 24 22 21 24
2 28614-EN
version: 1.1
Operation Zelio Control - Measurement and
control relays
Multifunction 3-phase control relays
RM22TA, RM22TU, RM22TR, and RM22TG
Operating principle
Multifunction 3-phase supply control relays monitor:
bb Own power supply
bb Correct sequencing of phases L1, L2, and L3
1
bb Fault signaling by LED
bb Phase failure, including in the case of voltage regeneration
bb Undervoltage from - 2…- 20 % of the supply voltage Un
bb Overvoltage from 2…20 % of the supply voltage Un
bb Asymmetry from 5…15 % of the supply voltage Un
4
vv failure of at least one of the three phases (U measured < 0.7 x Un)
vv asymmetry adjustable from 5…15 % of Un
bb If a sequencing or phase failure fault is detected, the relay opens instantly.
bb If an asymmetry fault is detected, the relay opens at the end of the time delay set
by the user.
bb On energization of the device with a detected measured fault, the relay stays
open.
Function diagram 5
bb Functions:
vv Sequence of phases L1, L2, L3
vv Phase failure
vv Asymmetry Asym
Phase L1
Phase L2
L3
L2
6
Phase L3
Asymmetry
Hysteresis
0%
Relay R/R1/R2
Outputs Tt Tt 7
Tt: time delay after crossing of threshold (adjustable on front panel)
10
28614-EN 3
version: 1.1
Operation (continued) Zelio Control - Measurement and
control relays
Multifunction 3-phase control relays
RM22TA, RM22TU, RM22TR, and RM22TG
3
30 % Un 30 % Un 30 % Un
Phase L1 L3
Phase L2 L2
Phase L3
Relay R/R1/R2
Outputs
5
Phases L1/L2/L3
Relays R/R1/R2
Output Tt Tt
8 v Phase failure
30 % Un 30 % Un 30 % Un
Phase L1
Phase L2
Phase L3
Relay R/R1/R2
9
Outputs
Hysteresis L3
10 <U
Phases L1/L2/L3
Relay R/R1/R2
Outputs Tt Tt
4 28614-EN
version: 1.1
Operation (continued), Zelio Control - Measurement and
references control relays
Multifunction 3-phase control relays
RM22TA, RM22TU, RM22TR, and RM22TG
Phase L1
100 %
3
0%
L3
100 %
Phase L2
0%
L2
4
100 %
Phase L3
0%
Relay R/R1/R2
Outputs
Tr Tr Tr Tr
6
sequence (0.1...30 s) 0.198
b Phase failure
b Asymmetry
b Phase
sequence
200…240 a 200…240 a On/Off delay 2 C/O 8 A
(0.1...30 s)
RM22TR31 0.090/
0.198
7
b Phase failure
b Undervoltage
RM22TA31 RM22TR31 and
overvoltage 380…480 a 380…480 a On/Off delay 2 C/O 8 A RM22TR33 0.090/
(0.1...30 s) 0.198
9
0.198
10
28614-EN 5
version: 1.1
Presentation, Zelio Control - Measurement and
description control relays
Liquid level control relays
RM22LA and RM22LG
Presentation
RM22LA and RM22LG liquid level control relays control one or two liquid levels, with
1 a fill or empty function:
Functions RM22LA 32MR/32MT RM22LG 11MR/11MT
Level 1/Level 2
Fill operation
Empty operation
Low sensitivity
2 Standard sensitivity
High sensitivity
Function performed
RM22LG11MR RM22LA32MT
Function not performed
Applications
These devices monitor the levels of conductive liquids.
4 They control the actuation of pumps or valves to regulate levels and are also
suitable for protecting submersible pumps against dry running, or protecting tanks
from “overflow”. They can also be used to control dosing of liquids in mixing
processes and to protect heating elements in the event of non-immersion.
They have a transparent, hinged cover on their front panel to avoid any accidental
alteration of the settings. This cover can be directly sealed.
5
b Application examples for compatible liquids:
v spring, town, industrial, and sea water
v metallic salt, acid, or base solutions
v liquid fertilizers
v non-concentrated alcohol (< 40 %)
v liquids in the food-processing industry: milk, beer, coffee, etc.
Description
6 RM22LG11MR RM22LG11MT 1 Configuration: selection of the
A1 A2 NC A1 A2 NC
operating mode (Fill or Empty) and the
sensitivity range (LS/St/HS)
Min Max C Min Max C 2 Sensitivity control potentiometer (kΩ or %)
RM22LG11MR RM22LG11MT
3 Configuration: selection of the number
of levels and theOn/Off time delay
7 1 1
4 Time delay control potentiometer Tt
40 60 40 60
30 70 30 70
2 2
Sens 80
20 Sens 20 80
10 90 10 90
5 100 KΩ 5 100 KΩ
3 Level
2 1 3 Level
2 1
5 Diagnostic button
R R
5 DIAGNOSTIC
5 DIAGNOSTIC
8
12 11 14 12 11 14
RM22LA32MR RM22LA32MT
A1 A2 NC A1 A2 NC
9 1
RM22LA32MR
HS
St.
LS
LS
St.
HS
1
RM22LA32MT
HS
St.
LS
LS
St.
HS
40 60 40 60
30 70 30 70
2 2
Sens 20 80 Sens 20 80
10 90 10 90
5 100% 5 100%
3 3
1 1 1 1
DELAY
DELAY
DELAY
DELAY
OFF
OFF
Level Level
ON
ON
2 2 2 2
10 20 R 10 20 R
4 Tt 5 25
4 Tt 5 25
5 5
0,1 30s 0,1 30s
10
DIAGNOSTIC DIAGNOSTIC
12 11 14 12 11 14
22 21 24 22 21 24
2 28617-EN
version: 1.1
Operation Zelio Control - Measurement and
control relays
Liquid level control relays
RM22LA and RM22LG
Operating principle
Liquid level control relays are designed to measure and control the levels of con-
ductive liquids by means of resistive probes.
The operating principle is based on measurement of the apparent resistance of the
1
liquid between two submerged probes. When this value is less than the threshold
setting on the front panel of the device, the relay changes state. To avoid
electrolytic phenomena, an AC current runs across the probes.
A selector switch on the front panel allows selection of the required function and
the sensitivity range. Control of a single level can be achieved by using the second
selector switch. In this case, the Max. level probe stays up in the air and an adjust-
2
able time delay avoids any wave effect. Both products activate their output relay
when a tank is either emptying or filling.
3
A selector switch on the front panel of these relays allows selection of the required
sensitivity range and the empty or fill function. A second switch allows selection of
the number of levels (1 or 2) and the type of time delay in the case of level 1 mode.
The position of these configuration switches is taken into account on energization.
b If the configuration switch is set to an unacceptable position, the product detects a
fault, the output relay stays open, and the LEDs flash to signal the position error.
b If the configuration switch position is changed while the device is operating, all the
LEDs flash, but the product continues to operate normally with the function selected
at the time of energization preceding the change of position.
b If the configuration switch is returned to the original position selected prior to the
4
last energization, the LEDs return to their normal state.
6
level, the contact opens to stop the emptying process.
vv Fill function
level: 2, function:
-- LS (Low Sensitivity: 250 W…5 kW)
-- St (Standard Sensitivity: 5 kW…100 kW)
-- HS (High Sensitivity: 50 kW…1 MW)
The output relay stays energized until the liquid reaches the Max. level probe.
As soon as the Max. level is reached, the contact opens and the pump stops.
When the level drops below the Min. level, the contact closes again and
7
pumping re-starts to raise the level.
Function diagram
bb Fill/Empty function (2 levels)
Supply Un
8
Max. level
Min. level
Relay
Outputs R/R1/R2
Relay
Outputs
R/R1/R2 9
10
28617-EN 3
version: 1.1
Operation (continued) Zelio Control - Measurement and
control relays
Liquid level control relays
RM22LA and RM22LG
2 When the liquid level rises above the probe for a time greater than the time delay
value Tt set on the front panel, the relay is energized and stays energized until the
liquid level drops back to the probe.
If the liquid drops back below the set level before the end of the time delay, the relay
does not energize.
Function diagram
3
bb Empty function T on
Supply Un
Level
Relay
R/R1/R2
Outputs
Tt Tt Tt
4
bb Control of one level, empty function
vv level: 1 - off delay functions:
-- LS (Low Sensitivity: 250 W…5 kW)
-- St (Standard Sensitivity: 5 kW…100 kW)
When the liquid level rises above the probe, the relay instantly energizes and stays
energized until the liquid again reaches the probe level for a time Tt set on the front
panel.
If the liquid drops back below the set level before the end of the time delay period,
the relay stays energized.
6 Function diagram
bb Empty function T off
Supply Un
Level
7 Relay
Outputs
R/R1/R2
Tt Tt Tt
When the liquid level drops below the probe for a time greater than the time delay
value Tt set on the front panel, the relay is energized and stays energized until the
liquid level rises back up to the probe.
If the liquid rises back above the set level before the end of the time delay period, the
9 relay does not energize.
Function diagram
bb Fill function T on
Supply Un
10
Level
Relay
R/R1/R2
Outputs
Tt Tt Tt
Tt: time delay after crossing of threshold
4 28617-EN
version: 1.1
Operation (continued), Zelio Control - Measurement and
references control relays
Liquid level control relays
RM22LA and RM22LG
When the liquid level drops below the probe, the relay instantly energizes and stays
2
energized until the liquid level again reaches the probe level and stays above it for
a time greater than the time delay period Tt set on the front panel.
If the liquid drops back below the set level before the end of the time delay period,
the relay stays energized.
Function diagram
bb Fill function T off
Supply Un
3
Level
Relay R/R1/R2
Outputs
Tt Tt Tt
10
28617-EN 5
version: 1.1
Presentation, Zelio Control - Measurement and
description control relays
1-phase or DC voltage control relays
RM22UA and RM22UB
Presentation
RM22UA and RM22UB 1-phase or DC voltage control relays monitor the following
1 functions:
Functions RM22 UA2●MR UA3●MR UA33MT UB34
Overvoltage (without memory)
Undervoltage (with/without memory)
Overvoltage (with/without memory)
2
Overvoltage or undervoltage
(windows mode)
Function performed
RM22UA21MR RM22UA31MR Function not performed
They feature:
b Dial pointer LED indicator for relay power ON status
b Relay output status LED
4 The settings are protected by a sealable cover and the control status is indicated
by an LED. The relays are designed for clip-on mounting on a DIN rail.
Applications
b Protection of electronic or electromechanical devices against overvoltage and
undervoltage
5 b Normal/emergency power supply switching
b DC motor overspeed control
b Monitoring of AC or DC supplies
b Battery and speed monitoring (with tacho-generator)
Description
6 RM22UA2●MR
A1 A2 M
RM22UA3●MR
A1 A2 M
1 Configuration: selection of operating
mode <U (undervoltage), >U
(overvoltage), >U> (overvoltage and
E1 E2 E3 E1 E2 E3
undervoltage), MEMORY - NO
MEMORY (with or without memory)
RM22UA23MR RM22UA31MR
MEMORY
NO
>U >U
<U <U
40 70 40 70
U value
2c 2a
30 80
7
30 80
U
>U 20 90 Value 20 90
Value 10 100% 10 100%
20 35 20 35
2b Undervoltage setting potentiometer <U
4a 4b
15 40 Hys/ 15 40
Hys
10 45 >U> 10 45
3 Tt 5 25
5
30s
5 DIAGNOSTIC DIAGNOSTIC
9
RM22UA33MT RM22UB34
1 6
>U > > U>
MEMORY
DELAY
MEMORY
DELAY
OFF
ON
NO
>U >U
<U <U
40 70 160 220
140 240
2a 2c
U 30 80
>U 120 260
Value 20 90
100 280
10 100%
80 300V
20 35 160 220
4b 2b
15 40 140 240
Hys/
<U 120 260
>U> 10 45
100 280
5 50% 80 300V
10 20 R 10 20 R
3 Tt 5 25
3 Tt 5 25
5
0,1 30s
5
0,1 30s
DIAGNOSTIC DIAGNOSTIC
10 12 11 14 12 11 14
22 21 24 22 21 24
2 28615-EN
version: 1.1
Operation Zelio Control - Measurement and
control relays
1-phase or DC voltage control relays
RM22UA and RM22UB
Operating principle
1-phase or DC voltage control relays monitor:
bb the voltage of 1-phase and DC supplies
bb their own supply voltage for the RM22UB model
1
An adjustable time delay, on crossing the thresholds, provides immunity to
transients, and prevents spurious triggering of the output relay.
The position of the configuration switch and the operating mode is read by the
product on energization:
bb If the configuration switch is set to an unacceptable position, the product detects
a fault, the output relay stays open, and the LEDs flash to indicate the position error. 3
bb If the configuration switch position is changed while the device is operating, all
the LEDs flash, but the product continues to operate normally with the function
selected at the time of energization before position change.
bb If the configuration switch is returned to the original position selected prior to the
last energization, the LEDs return to their normal state.
7
bb Overvoltage/undervoltage with memory
If “Memory” mode is selected, the relay opens when crossing of the threshold is
detected and then stays in that position. The power must be switched off to reset
the product.
Function diagram
bb Function: Overvoltage control > U
vv Without memory
Supply Un 8
Threshold >U
Hysteresis
U
Relay R/R1/R2
Outputs
Tt
9
vv With memory
Supply Un
Threshold >U
Hysteresis
Relay R/R1/R2
U
10
Outputs
Tt
28615-EN 3
version: 1.1
Operation (continued) Zelio Control - Measurement and
control relays
1-phase or DC voltage control relays
RM22UA and RM22UB
U
2 Hysteresis
Threshold <U
Relay R/R1/R2
Outputs
Tt
vv With memory
3 Supply Un
Hysteresis
U
Threshold <U
Relay
R/R1/R2
Outputs
Tt
Function diagrams
Threshold >U
Hysteresis
Hysteresis U
8 Threshold <U
Relay R/R1/R2
Ouputs Tt Tt
Tt: time delay after crossing of threshold
10
4 28615-EN
version: 1.1
References Zelio Control - Measurement and
control relays
1-phase or DC voltage control relays
RM22UA and RM22UB
References
Function Rated supply Measurement Time delay Output Reference Weight
voltage
V
range
V kg/lb
1
b Overvoltage 24…240 z 0.05…5 z No 2 C/O 8 A RM22UA21MR 0.110/
without memory 0.242
RM22UA23MR RM22UA33MR b Overvoltage and 24…240 z 0.05…5 z Off delay 2 C/O 8 A RM22UA31MR 0.110/
undervoltage with/ (0.1...30 s) 0.242
without memory
b Overvoltage and
undervoltage with 24…240 z 1…100 z Off delay 2 C/O 8 A RM22UA32MR 0.110/
3
memory window (0.1...30 s) 0.242
10
28615-EN 5
version: 1.1