Professional Documents
Culture Documents
Basf Masterseal NP 474 Tds
Basf Masterseal NP 474 Tds
DESCRIPTION PACKAGING
MasterSeal NP 474 is a single component MasterSeal NP 474 is supplied in 310ml
polyurethane based sealant for floor joints, wall cartridge and 600ml sausage.
joints in public areas, prisons, schools, colleges,
hospitals because of excellent resilience and COLOURS
pick resistance. It cures under the influence of MasterSeal NP 474 is available in:
atmospheric humidity and forms a chemical, Concrete Grey (RAL 7004), Off White (RAL
good mechanical resistant and elastic joint 1015) and White (RAL 9010)
sealant.
STANDARDS
FIELD OF APPLICATIONS SNJF F25E
• For interior and exterior application. EN 15651-1: F-EXT-INT-CC 25HM
• For floor connection and expansion joints in EN 15651-4: PW-EXT-INT-CC 20HM
buildings and civil structures NF P 85-610
• Non corrosive
• For pedestrian and traffic areas (e.g. car TECHNICAL DATA*
decks/parks)
• For warehouse and production areas Density 1.19g/ml
• For ceramic tile coverings exposed to traffic Working temperature from +5°C to +40°C
(e.g. public areas, shopping centers) Movement Capability ± 25 % of joint width
Sag flow ISO 7390 <3mm
• For medium chemical and mechanical loads
Skinning time approx. 70 mins
(e.g. canteen kitchens, garages)
Curing rate approx. 3mm/day
• As a strong resilient elastic adhesive for Shore A hardness ISO 868 approx. 45
construction and industrial applications. E-Modulus at 100% approx. 0.6N/mm²
elongation
Contact your local Master Builders Solutions
Elongation at break 450%
representative regarding any application Service temperature range -30°C to +70°C
required not mentioned here. Tensile strength 1N/mm²
FEATURES AND BENEFITS
APPLICATION METHOD
• Single component – easy to use Preparation:
• Good mechanical and chemical resistance All substrates (new and old) must be structurally
(see table) sound, free of laitance and loose particles and
• Excellent adhesion even without primer – see clean of oil, grease, rubber skid marks, paint
section priming stains and other adhesion impairing
• Fast curing contaminants.
• Forms a smooth blister free surface, only
when applied onto dry substrates Concrete, cementitious substrates (e.g.
• High elastic recovery screeds, etc.)
• Good weathering and aging resistance Prepare the surface by grinding, sandblasting, or
• No thermo plasticity (no temperature wire brushing. Remove remaining dust and
softening) particles by suitable measures such as the use
• Fast skinning time. Low risk of dirt pickup. of compressed air.
• Complies to ISO 11600, IVD leaflet No. 1 Repair damaged joint edges with appropriate
• Quality audited. MasterEmaco repair mortars.
MasterSeal® NP 474
Metal Allow primer to flash off before sealant
Remove scale, rust, coatings and any chemical application and apply MasterSeal NP 474 within
residue or film from the metal. the open time of the primer.
BASF_CC-UAE/Sl_474_05_16/v2/11_16
The technical information and application advice given in this BASF publication are based on the present state of
STATEMENT OF our best scientific and practical knowledge. As the information herein is of a general nature, no assumption can be
RESPONSIBILITY made as to a product's suitability for a particular use or application and no warranty as to its accuracy, reliability or
completeness either expressed or implied is given other than those required by law. The user is responsible for
checking the suitability of products for their intended use.
Field service where provided does not constitute supervisory responsibility. Suggestions made by BASF either
NOTE orally or in writing may be followed, modified or rejected by the owner, engineer or contractor since they, and not
BASF, are responsible for carrying out procedures appropriate to a specific application.
BASF Construction Chemicals UAE LLC Disclaimer: the LRQA mark relates
P.O. Box 37127, Dubai, UAE to certified management system and
Tel: +971 4 8090800, Fax: +971 4 8851002 not to the product mentioned on this
www.master-builders-solutions.basf.ae datasheet