URR-14 “Write your Roll number” t
(An Autonomous Institute under Kakatiya University, Warangal)
B.Tech, (E&IE and CSE) V Semester
S&S KAKATIYA INSTITUTE OF TECHNOLOGY & SCIENCE, WARANGAL 06015
xneew
I-Mid Semester Examination
‘UI4EI503 MICROPROCESSORS AND INTERFACING
Date: 01.11.2018 Note: 1. Answer all the questions,
‘Time: 2 Hrs}
1 Answer the following in brief.
aooe
oe
Explain IN and OUT instructions,
Write the BSR mode control word Format of 8255 PPI and explain.
Explain DMA mode of Data Transfer,
Explain synchronous and asynchronous modes of data transfer.
With the help of a neat functional block diagram explain the operation of 8255 PPI.
Write the control word Format for I/O mode of 8255 PPI and explain various 1/O
transfer modes,
(oR)
‘Write a brief note on 8086 interrupts.
An 8-bit DAC is interfaced to 8086 through PORT-A of 8255. Draw a neat interfacing
diagram and write an 8086 ALP to generate a Square wave at the output of DAC.
Write an ALP for interfacing of Keyboard and Seven segment display with 8086 using
8255 in mode 0.
An 68-bit ADC is interfaced to 8086 through PORT-A of 8255 and START and EOC pins
of ADC are connected to CO and C7 pins of port C of 8255. Draw a neat interfacing
diagram and write an 8086 ALP to read the output of ADC.
(OR)
With the help of a neat functional block diagram explain the working of 8257 DMAC.
Explain in detail about RS-232 serial bus standards,
With the help of a neat functional block diagram explain the working of 8254
Programmable Interval Timer.
Explain various modes of operation of 8254 Programmable Interval Timer.
(OR)
Write a brief note on GPIB / IEEE-488 bus.
List and explain the major components of 8251 USART.
Paper set by: Prof. K Sioani (CC), Prof. M.Sreelatha, Sri BJecoan, Sri G.Raju
——-Question Paper Ends—
Page 1 of 2
[Max. Marks: 25
BRN
wenee
Date: 15.11.2017 No!
‘Time: 2 Hrs
* “Write your Roll number” ——>
KAKATIYA INSTITUTE OF TECHNOLOGY & SCIENCE, WARANGAL-506015
(An Autonomous Institute under Kakatiya University, Warangal)
B.Tech. (E&I, CSE) V Semester, II-Mid Semester Examination
(U14EI503): MICROPROCESSORS AND INTERFACING
. Answer all the questions.
Max. Marks: 25
1. Answer the following in brief.
a
pos
List out sequence of Initializing 8259PIC using flowchart.
Explain about “Key Debouncing” technique used in keyboard interfacing,
Give the details of mode set word of 8254 PTC.
Explain about each bit in initialization command word of 8251.
With the help of a neat functional block diagram explain 8255 PPI and explain its
BSR mode.
With the help of neat schematic diagram explain the interfacing of an 8-bit DAC to
8086 processor through “Port A” of 8255. Write an ALP to generate a triangular
wave at the output pin of DAC.
(or)
Explain in detail about 8259 PIC with the help of neat block diagram. Explain about
various interrupt priority resolution methods possible with 8259.
Explain about various dedicated interrupts of 8086 MP. Write about Interrupt
Vector Table (IVT) and how the vector address of various interrupt service routines
‘would be determined by 8086 MP.
With the help of a neat sketch explain the interfacing of a Hex-Keyboard to 8086
MP through the 8255PPI and explain about the routine that can read the key-code
from the keyboard using a flowchart.
‘A four phase stepper motor (1.82/step) to 8086 microprocessor through 8255. Draw
necessary hardware diagram and write an 8086ALP to rotate the shaft of the motor
in clockwise direction for 1 revolution.
(oR)
Draw a neat functional block diagram of 8257 DMA controller and mention all its
internal registers.
Explain the working of 8254 PTC with the help a neat functional block diagram.
Explain various Timer/Counter modes of 8254 PTC with help of neat timing
diagrams.
Explain the serial communication using Data Terminal Equipment (DTE) and Data
Communication Equipment (DCE). Brief about RS-232 serial bus standards.
(OR)
Draw a neat functional block diagram of 8251 and explain about various modes of
serial communication.
With the help of block diagram explain the architecture of IEEE-488. Brief about the
sequence of operations required before the transmission of data.
—Question Paper Ends—
1
2]
2)
(1
Bl
Bl
BI
Bl
B)
i)
B)
8)
Bl
8)
BI)
Bl)
Question Paper Set by: 1. Dr. K. Venu Madhav, 2. Sri B. Jeevan, 3. Smt. B. Smitha and Sri G: Raju