Professional Documents
Culture Documents
98 140656 A01 Installation Guide Sailor 6588 Dgnss Receiver
98 140656 A01 Installation Guide Sailor 6588 Dgnss Receiver
Installation guide
42.5 mm
Cable RJ45
5m
SAILOR 6588 DGNSS Receiver
190 mm
Cable Tie Fuse
5x200 mm (10 pcs.) (1 A)
Screw M4x20
42.5 mm
Cable RJ45
5m
SAILOR 6588 DGNSS Receiver
TORX A2
Mounting tool for Fuse Puller
terminal blocks
190 mm
Screw M4x20
42.5 mm
(5 pcs.)
Cable RJ45
5m
SAILOR 6588 DGNSS Receiver
TORX A2
Mounting tool for Fuse Puller
terminal blocks
190 mm
Screw M4x20
(5 pcs.)
TORX A2
(5 pcs.)
270 mm
42.5 mm
Screw ST3.9x33
User Manual Installation Guide TORX 20
SAILOR 6588 DGNSS Receiver SAILOR 6588 DGNSS Receiver (5 pcs.)
4 x M4 or hole for
15.5 mm
self-tapping ø3.8 mm
270 mm
Power: Lit when the device is on.
RAIM: Indicates the quality of the position data.
The RAIM level is specified by the user on the Control Panel.
Red: The RAIM status is ”unsafe”.
Green: The RAIM status is ”safe”.
Yellow: Not enough satellites are available for RAIM calculation
124 mm
190 mm
J15 - IN 2
GND OUT be SBAS or a Beacon.
270 mm
J18 - OUT 2 GND
J13 - IN 1
RXA
J17 - OUT 1
TXA
RX GND
TXA
J14 - ALARM
NO
ON/OFF Status
SHIP GND Green: Beacon Station – 1 second interval.
RXB TXB TXB COM
Cable recommendation
12 mm 246 mm 12 mm
Minimum cable entry
270
•
mm
Alarm: Shielded two wires
Screw ST3.9x33
• LAN: Cat5e or better, shielded (STP)
Disclaimer: Any responsibility or liability for loss or damage in connection with the use of this product and the accompanying documentation is disclaimed by Thrane & Thrane. The information in this manual is provided for information
purposes only, is subject to change without notice and may contain errors or inaccuracies. Manuals issued by Thrane & Thrane are periodically revised and updated. Anyone relying on this information should acquire the most current
version e.g. from cobham.com/satcom or from the distributor. Thrane & Thrane is not responsible for the content or accuracy of any translations or reproductions, in whole or in part, of this manual from any other source.
Thrane & Thrane A/S trading as Cobham SATCOM
Copyright © 2015 Thrane & Thrane A/S. All rights reserved.
4 x M4 or hole for
15.5 mm
self-tapping ø3.8 mm
270 mm
Power: Lit when the device is on.
RAIM: Indicates the quality of the position data.
The RAIM level is specified by the user on the Control Panel.
Red: The RAIM status is ”unsafe”.
Green: The RAIM status is ”safe”.
Yellow: Not enough satellites are available for RAIM calculation
124 mm
190 mm
be SBAS or a Beacon.
OUT J21 - PPS
GND OUT
270 mm
J15 - IN 2 J18 - OUT 2 GND
J13 - IN 1
RXA
J17 - OUT 1
TXA
RX GND
TXA
J14 - ALARM
NO
ON/OFF Status
SHIP GND Green: Beacon Station – 1 second interval.
SBAS – 3 second interval.
42.5 mm
RXB TXB TXB COM
RX GND TX GND TX GND NC
50.5 mm
Cable recommendation
12 mm 246 mm 12 mm
Minimum cable entry
270 mm
• Alarm: Minimum 0.15 mm² (AWG26), two-wire
Screw ST3.9x33
• LAN: Cat5e or better, shielded (STP)
Disclaimer: Any responsibility or liability for loss or damage in connection with the use of this product and the accompanying documentation is disclaimed by Thrane & Thrane. The information in this manual is provided for information
purposes only, is subject to change without notice and may contain errors or inaccuracies. Manuals issued by Thrane & Thrane are periodically revised and updated. Anyone relying on this information should acquire the most current
version e.g. from cobham.com/satcom or from the distributor. Thrane & Thrane is not responsible for the content or accuracy of any translations or reproductions, in whole or in part, of this manual from any other source.
Thrane & Thrane A/S trading as Cobham SATCOM
Copyright © 2015 Thrane & Thrane A/S. All rights reserved.
4 x M4 or hole for
15.5 mm
self-tapping ø3.8 mm
270 mm
Power: Lit when the device is on.
RAIM: Indicates the quality of the position data.
The RAIM level is specified by the user on the Control Panel.
Red: The RAIM status is ”unsafe”.
Green: The RAIM status is ”safe”.
Yellow: Not enough satellites are available for RAIM calculation
124 mm
190 mm
12 mm 246 mm 12 mm
Cable recommendation
Minimum cable entry
Disclaimer: Any responsibility or liability for loss or damage in connection with the use of this product and the accompanying documentation is disclaimed by Thrane & Thrane. The information in this manual is provided for information
purposes only, is subject to change without notice and may contain errors or inaccuracies. Manuals issued by Thrane & Thrane are periodically revised and updated. Anyone relying on this information should acquire the most current
version e.g. from cobham.com/satcom or from the distributor. Thrane & Thrane is not responsible for the content or accuracy of any translations or reproductions, in whole or in part, of this manual from any other source.
Thrane & Thrane A/S trading as Cobham SATCOM
Copyright © 2015 Thrane & Thrane A/S. All rights reserved.
System Configuration - Example
SAILOR 6285 SAILOR 6286 For further information about installation, download the
GPS Antenna - Active DGNSS Antenna - Active
Installation manual 98-145263 from www.cobham.com/satcom
ALARM ACK
J22
J19
J21
LOG
PWR
TEST
PPS
J15 ACC
J18 AUX
J16 12-24VDC +
OUT 2
IN 2 12-24VDC -
ON_IN J12
ON_OUT
IN/OUT
J13 J17 J14
SHIP GND
ALARM
OUT 1
J2
IN 1
J6
12-24 VDC
(int. fuse 3.15 A)
ON_IN ON_OUT
VBAT- 12-24 VDC
The device requires ON_IN to be connected to VBAT- in order to power up.
VBAT+ (int. fuse 1 A)
This can be done by a dedicated switch, permanent wiring or connection Shield
to a Cobham device supporting ON_OUT (e.g. SAILOR 6004 Control Panel).
Terminal Connections:
IN 1: Input for IEC61162-1/2, NMEA0183. IN/OUT: Input/Output for IEC61162-1/2, NMEA0183.
* In a GNSS system this port can also be configured PPS: Pulse Pr. Second. Only output with valid GNSS fix.
as RTCM SC-104 input. Open Drain.
IN 2: Input for IEC61162-1/2, NMEA0183. Max 50V/300 mA.
* In a GNSS system this port can also be configured LOG: Speed LOG output. Default 200 pulses pr NM.
as RTCM SC-104 input. 50 ms pulses.
OUT 1: Output for IEC61162-1/2, NMEA0183. Open Drain.
* In a DGNSS system this port can also be configured Max 50V/300 mA.
as RTCM SC-104 output. ALARM: Internal alarm relay output.
OUT 2: Output for IEC61162-1/2, NMEA0183. Max 1 A, 125 V AC/60 V DC.
* In a DGNSS system this port can also be configured
as RTCM SC-104 output. * To be configured via the service interface.
The procedure described below configures the system to a GNSS 4. Select DGNSS on the left side.
system. If the system is to be configured as a DGNSS system, 5. Tab the Install button on the right side.
refer to the SAILOR 6588 Installation manual 98-145263 6. When prompted for the user-level password, enter it
(Password: user), and tab Apply.
1. Connect the DGNSS Receiver and the Control Panel with 7. After succesfull installation the DGNSS Receiver and the
the Ethernet cable. Control Panel must be paired. So tab the Paired with Device
2. Power up the DGNSS Receiver and the Control Panel. on the right side.
8. Choose the DGNSS Receiver (See the serial number on the
Control Panel: left side of the DGNSS Receiver).
1. Enter the System App. 9. After sucessfull pairing you can start the GNSS app on the
2. Tab the item Applications. home screen.
3. Select the tab Available in the upper right corner of the screen.
98-140656-A
www.cobham.com/satcom