771, 772, 773 Series Servovalves

You might also like

Download as pdf or txt
Download as pdf or txt
You are on page 1of 8

771, 772, 773 Series

Servovalves
771/2/3 SERIES
TWO STAGE SERVOVALVES

771/2/3 SERIES SERVOVALVES a cantilever spring.The valve deflection of the armature/flap- Once the restoring torque
design is simple and rugged for per assembly within the flexure becomes equal to the torque
The 771/2/3 Series flow con-
dependable, long life operation. tube. Deflection of the flapper from the magnetic forces, the
trol servovalves are throttle
These valves are suitable restricts fluid flow through one armature/flapper assembly
valves for 3- and preferably
for electrohydraulic position, nozzle which is carried through moves back to the neutral
4-way applications.They are a
speed, pressure or force con- to one spool end, displacing position and the spool is held
high performance, two-stage
trol systems with high dynamic the spool. open in a state of equilibrium
design that covers the range of
response requirements. Movement of the spool until the command signal
rated flows from 1 to 15 gpm
opens the supply pressure port changes to a new level.
at 1000 psi valve drop.The
(P) to one control port, while In summary, the spool
output stage is a closed center, An electrical command signal simultaneously opening the position is proportional to the
Principle of operation
four-way sliding spool.The pilot (flow rate set point) is applied tank port (T) to the other input current and with con-
stage is a symmetrical double- to the torque motor coils, and control port.The spool motion stant pressure drop across the
nozzle and flapper, driven by creates a magnetic force which also applies a force to the valve, flow to the load is pro-
a double air gap, dry torque acts on the ends of the pilot cantilever spring, creating a portional to the spool position.
motor. Mechanical feedback of stage armature.This causes a restoring torque on the
spool position is provided by
armature/flapper assembly.

VALVE FEATURES

➣ 2-stage design with dry torque motor ➣ Rugged, long-life design

➣ Low friction double nozzle pilot stage ➣ High resolution, low hysteresis

➣ High spool control forces ➣ Completely set-up at the factory

➣ High dynamics ➣ Small body size

The actual flow is dependent ∆p


upon electrical command signal Q = QN
∆pN
and valve pressure drop.The
flow for a given valve pressure
drop can be calculated using Q [gpm] = calculated flow
the square root function for QN [gpm] = rated flow
sharp edge orifices: ∆p [psi] = actual valve
pressure drop
∆pN [psi] = rated valve
pressure drop

This catalog is for users with technical system are given, the user has to check the Intrinsically safe valve versions are available for use in hazardous locations.
knowledge.To ensure that all necessary suitability of the products described here. Specific models are certified to FM,ATEX, CSA, and TIIS standards. Contact the factory
characteristics for function and safety of the In case of doubt, please contact Moog Inc. for details.

2
771/2/3 SERIES
GENERAL TECHNICAL DATA

Operating Pressure
40.0
ports P,T,A and B up to 3,000 psi

Flow Rate Q (gpm)


Temperature Range 30.0
Fluid -40° to 275°F
Ambient -40° to 275°F 20.0
Seal Material Viton others on request
Operating Fluid Compatible with common
hydraulic fluids, other fluids
on request. 10.0
pm
Recommended viscosity 60-450 SUS @ 100°F 0g
15.
System Filtration: High pressure filter (without bypass, pm
but with dirt alarm) mounted in the main flow and if possible, 0g
10.
5.0
directly upstream of the valve.
Class of Cleanliness: The cleanliness of the hydraulic fluid
greatly effects the performance (spool positioning, high resolution) gpm
and wear (metering edges, pressure gain, leakage) of the servovalve. 5.0

2.0
Recommended Cleanliness Class
For normal operation ISO 4406 < 14/11
For longer life ISO 4406 < 13/10 gpm
2.5
Filter Rating recommended
For normal operation ß10 ≥ 75 (10 µm absolute) 1.0
For longer life ß5 ≥ 75 (5 µm absolute)
Any position, fixed or moveable.
gpm
Installation Operations
Vibration 30 g, 3 axes 1.0
Weight 2.0 lb [.09 kg]
EN50529P: class IP65, with .05
200 300 400 500 700 1000 2000 3000
Degree of Protection
mating connector mounted.
Valve Pressure Drop ∆p (psi)
Delivered with an oil sealed
shipping plate.
Shipping Plate

Valve flow for maximum valve opening (100% command


Valve Flow Diagram

signal) as a function of the valve pressure drop.

P B T A
View from Pressure Side

3
771/2/3 SERIES
TECHNICAL DATA

Model…Type 771 771 773


Mounting Pattern ISO 10372 - 02 - 02 - 0 - 92
Valve Body Version 4-way
2-stage with spool–bushing assembly
Pilot Stage Nozzle/Flapper, Highflow
Pilot Connection Optional, Internal or External Internal only
Rated Flow (±10%) at ∆p = 1,000 psi N

Standard [gpm] 1.0 2.5 5.0 10.0 15.0


Response Time* Standard [ms] 6 6 6 10 16
Threshold* [%] < 0.5
Hysteresis* [%] < 3.0
Null Shift at ∆T = 100˚F [%] < 2.0
Null Leakage Flow* max. [gpm] 0.35
* Measured at 1,000 psi pilot or operating pressure

curves with ±40% and ±100%


Typical characteristic 771 Series 772 Series 773 Series
+2 +2 +2

input signal, measured at


Amplitude Ratio (dB)
Amplitude Ratio (dB)

Amplitude Ratio (dB)

0 0 0

3,000 psi operating pressure.


-2 -2 -2
-4 -4 -4
3000 psi DTE-24
-6 at 100˚F (38˚C) 120 -6 3000 psi DTE-24 120 -6 120
Rated Current: at 100˚F (38˚C)
-8 100 -8 Rated Current: 100 -8 3000 psi DTE-24 100
±40% at 100˚F (38˚C)
Phase Lag (degrees)

Phase Lag (degrees)


Phase Lag (degrees)

-10 ±100% 80 -10 ±40% 80 -10 Rated Current: 80


±100%
60 60
±40%
±100% 60
40 40 40
20 20 20

10 20 30 50 70 100 200 300 500 1000 10 20 30 50 70 100 200 300 500 1000 10 20 30 50 70 100 200 300 500 1000
Frequency (Hz) Frequency (Hz) Frequency (Hz)
Frequency Response Frequency Response Frequency Response
of 1, 2.5, and 5 gpm Servovalves of 10 gpm Servovalves of 15 gpm Servovalves

4
771/2/3 SERIES
INSTALLATION DRAWINGS

1.88 1.88
[47.8] [47.8] 4X .221 [5.61] THRU
.014 M
2.550
1.12 MAX [64.77] OR
[28.4] 4X .265 [6.73] THRU
(OPTION) 1.275 .007 M
[32.39]

1.39 MAX
1.06
[35.3] [26.9]
1.343
[34.11]
1.00
[25.4]

.671
.844 [17.04]
[21.44]
1.688
[42.88]

PIN D PIN A ELECTRICAL CONNECTOR 2.12


[53.8]
PIN C PIN B

2.81
[71.4]
2.18
[55.4] 1.75
1.56 [44.5]
1.03 [39.6] MTG HGT
[26.2]
P

LOCATING PIN .062 .12 MAX


[1.57] [3.0]
EXTERNAL NULL ADJUST
3/32 IN. HEX
SOCKET

TYPICAL SUBPLATE MANIFOLD The mounting manifold


must conform to
C VALVE MOUNTING
3.090
Surface to which valve is
ISO 10372-03-03-0-92.
.007 M 1.688
RETURN PORT T

1.25
4 HOLES (42.9) A PORT CIRCLE mounted requires a 32 [∆∆]
CONTROL PORT B .844
(21.4)
finish, flat within 0.002[0.05] TIR.
2X .62
CONTROL PORT A

Flow out of Port B will increase


For External Null Adjust:

.672
1.295 with clockwise rotation of null
3.25 2.590
1.344 (17.1) adjust screw (3/32 hex key).
(34.1)

1.63
.500
Flow bias is continually varied
For External Null Adjust:

for a given port as the null


2

adjust is rotated.
B PORT DIA VALVE MOUNTS ON
THIS MANIFOLD SURFACE
.010 M .390
4 HOLES .156 .20
1.545 .026 M
4X PORT PER SAE J1926
.750-16UNF-2B DASH 8
STR THD O-RING BOSS
PRESSURE PORT P

(.50 TUBE OD REF) 32


.002

4X .344 THRU
.531 .48 PRESSURE
2X .62
.013 M
1.88
3.75

TYPICAL SUBPLATE MANIFOLD


Model A Port B Port C Mtg
Number Circle Dia Dia Holes
771-XXX .625 .191 .190-32 NF
772-XXX .780 .261 .190-32 NF
773-XXX .937 .312 .250-20 NC
5
771/2/3 SERIES
ELECTRICAL CONNECTIONS

A four-pin electrical con- The servovalve responds


Rated current and Coil connections Servoamplifier

A variety of coils are available nector (that mates with an to input current, therefore,
coil resistance

for 771/2/3 Series Servovalves, MS3106F14S-2S) is standard. a servoamplifier that has


which offer a wide choice of All four torque motor leads high internal impedance
rated current. See Table 1. are available at the connector (as obtained with current
so external connections can feedback) should be used.
be made for series, parallel This will reduce the effects
or differential operation. of coil inductance and will
771/2/3 Series Servovalves minimize changes due to
can be supplied on special coil resistance variations.
order with other connectors
or a pigtail.

ELECTRICAL Parallel Series Single


CONNECTIONS
(Examples with typical 771/2/3 series coils) A B C D A B C D A B C D

Coil Resistance [Ω] 100 400 200


Rated Current [mA] ±15 ±7.5 ±15
Electrical Power [W] .023 .023 .045
Connections for Valve Opening A and C (+) A (+), D (-) A (+), B (-)
P ➧ B, A ➧ T B and D (-) B and C connected or C (+), D (-)

Note: Before applying electrical signals the pilot stage has to be pressurized.

TABLE 1

Nominal Recommended Rated Current–mA Approximate Coil Inductance*–Henrys


Resistance
Per Coil at Parallel,
77˚F (25˚C) Ω Differential or Single Series Coils Single Coils Series Coils Parallel Coils
Coil Operation
80 ±40 ±20 0.22 0.66 0.18

200 ±15 ±7.5 0.72 2.20 0.59

1000 ±8 ±4 3.20 9.70 2.60

* Measured at 50 Hz

6
771/2/3 SERIES
ORDERING INFORMATION
SPARE PARTS AND ACCESSORIES

Model Number Type Designation


771, 772, 773 • • • • • • • • • • • • • • • • •

Signals for 100% Spool Stroke


±4 mA series
Optional Feature
Series specification 4
Intrinsically safe H ±7.5 mA series
±20 mA series
K
L
N ±30 mA series
±100 mA series
Model Designation
Assigned at the factory
Z
Y Special signal (see spec. sheet)

Factory Identification (Revision Level) Valve Connector


A Connector C1 (A) – side (RH)
Valve Version B Connector C2 (B) – side (LH)
S Standard response X Special connector

Rated Flow Seal Material


QN[gpm] at ∆pN = 1,000 psi V Fluorocarbon
Standard High Response N NBR (Buna)
04 1 771 series only Others on request
10 2.5 771 series only
19 5.0 772 series only
10.0 772 series only
Pilot Connections and Pressure
Pressure [psi] Supply
38
15.0 773 series only
250 to 3,000 internal
57
A

Maximum Operating Pressure pp and Body Material


3,000 psi aluminum
Spool Position without Electrical Signal
M Mid position
F

Main Spool Type


4-way / axis cut / linear
Pilot Stage
F Standard dynamics
O
D 4-way / +/-10% overlap / linear
X Special

Preferred configurations highlighted.


All combinations may not be available.
Options may increase price and delivery.
Technical changes are reserved.

SPARE PARTS AND ACCESSORIES


O-Rings (included in delivery),
for P,T, A and B FPM 85 Shore Moog P/N
771 ID 0.239 x 0.070 42082-007
772 ID 0.364 x 0.070 42082-013
773 ID 0.426 x 0.070 42082-022
Mating Connector, waterproof IP 65 (not included in delivery) 49054F14S2S (MS3106F14S-2S)
Flushing Block
771 and 772 A01704-1K1
773 A01704-2K1
Mounting Bolts (included in delivery)
771 and 772 .190-32 NF x 2.0 long (4 pcs.) C39674-132
773 .250-20 NC x 2.25 long (4 pcs.) A31324-136Z
Field Replaceable Filter Kit B52555RK54K1

7
Australia Mulgrave
Brazil São Paulo
China Hong Kong
Shanghai
Denmark Cöpenhagen
England Tewkesbury
Finland Espoo
France Rungis

Germany Böblingen
India Bangalore
Ireland Ringaskiddy
Italy Brescia
Malnate
Japan Hiratsuka
Korea Seoul
Luxembourg Luxembourg City
Philippines Baguio
Singapore Singapore
Spain Orio
Sweden Askim
USA East Aurora

Moog Inc., East Aurora, NY 14052-0018


Telephone: +1-716-652-2000
Fax: +1-716-687-7910
Toll Free: +1-800-272-MOOG
www.moog.com/industrial
©2007 Moog Inc. All changes are reserved.

CDL6304 Rev G 500-223 0807

You might also like