This document summarizes 10 warnings or errors from a structural analysis software (STAAD) for a project (GHS81). For each warning or error, it lists the issue number, a brief description of the comment, the software's response, and recommendations for how to address or remedy the issue. Common remedies include checking for modeling errors, applying appropriate analysis parameters, increasing structural member sizes, and performing additional checks of story drift, stiffness, and irregularities. The warnings cover issues like ignored commands, zero stiffness, instability, shear checks, soft stories, curved beams, and minimum column dimensions.
This document summarizes 10 warnings or errors from a structural analysis software (STAAD) for a project (GHS81). For each warning or error, it lists the issue number, a brief description of the comment, the software's response, and recommendations for how to address or remedy the issue. Common remedies include checking for modeling errors, applying appropriate analysis parameters, increasing structural member sizes, and performing additional checks of story drift, stiffness, and irregularities. The warnings cover issues like ignored commands, zero stiffness, instability, shear checks, soft stories, curved beams, and minimum column dimensions.
This document summarizes 10 warnings or errors from a structural analysis software (STAAD) for a project (GHS81). For each warning or error, it lists the issue number, a brief description of the comment, the software's response, and recommendations for how to address or remedy the issue. Common remedies include checking for modeling errors, applying appropriate analysis parameters, increasing structural member sizes, and performing additional checks of story drift, stiffness, and irregularities. The warnings cover issues like ignored commands, zero stiffness, instability, shear checks, soft stories, curved beams, and minimum column dimensions.
This document summarizes 10 warnings or errors from a structural analysis software (STAAD) for a project (GHS81). For each warning or error, it lists the issue number, a brief description of the comment, the software's response, and recommendations for how to address or remedy the issue. Common remedies include checking for modeling errors, applying appropriate analysis parameters, increasing structural member sizes, and performing additional checks of story drift, stiffness, and irregularities. The warnings cover issues like ignored commands, zero stiffness, instability, shear checks, soft stories, curved beams, and minimum column dimensions.
Do check if any non relevant statement is present. If is it, then either provide ‘*’ This refer to whether the before statement or remove ‘Command’ are misinterpret to it. Above line ignored! Check possible STAAD or Could possibly have 1. Do check for possible syntax or typing error. Irregular connectivity btw multiple structure in project. beams or missed some node & Do check for properly beam elements. alignment of Node & Beam Number (Renumber Node & Beam)
List of Warning(s) Occurs as Follow,
S.NO. COMMENT(S) RESPONSE REMEDY
IF THIS UBC/IBC ANALYSIS HAS This refer to STAAD tends to
TENSION/COMPRESSION OR REPEAT run function multiple times Apply ‘PERFORM ANAYLSIS’ LOAD OR RE-ANALYSIS OR SELECT based on required analysis so 2. then ‘CHANGE’ after each OPTIMIZE, THEN EACH UBC/IBC CASE in order to sustain that static seismic load case SHOULD BE FOLLOWED BY PERFORM seismic values this Commands ANALYSIS & CHANGE. must be applied.
ZERO STIFFNESS IN DIRECTION 4 AT
JOINT ___ EQN.NO. ____ LOADS APPLIED OR DISTRIBUTED HERE FROM ELEMENTS WILL BE IGNORED. 1. Release only My and Mz 3. THIS MAY BE DUE TO ALL MEMBERS in required beam and AT THIS JOINT BEING RELEASED OR From Design parameter EFFECTIVELY RELEASED IN THIS Concern Member are released apply ‘TORSION 1’ for DIRECTION. in Mx, My, Mz which make zero neglecting Mx in Beam. stiffness ability for certain nodes. 2. Release Partial Release INSTABILITY AT JOINT 348 of value of 0.99 in MP or 4. DIRECTION = MX PROBABLE CAUSE MPX, MPY, MPZ. SINGULAR-ADDING WEAK SPRING THE LOAD# __ IS AN 1893 RESPONSE From STAAD, ‘Print Story Drift’ SPECTRUM LOAD CASE. STORY DRIFT Apply ‘CHECK STORY DRIFT’ applied but this is efficient for 5. IS NOT CALCULATED. PERFORM after each Response IS 456 and code of concrete but STORY DRIFT CHECKING DURING Spectrum Load case. for IS 13920 differs. RESPONSE SPECTRUM ANALYSIS.
To Perform Ordinary Shear
check, Apply ENSH 1 Parameter. Two ways of performing LENGTH TO DEPTH RATIO FOR Enhance shear check for MEMBER __ IS LESS THAN 2.5. beam are, DEEP BEAM IS NOT DESIGNED. Refer Cl 40.5 from IS 13920 ASSUMING IT TO BE A PART OF A 1. Apply ENSH __ (along CONTINUOUS BEAM AND AWAY 6. with certain distance the FROM THE CRITICAL SECTION FOR Certain Continuous Beam are shear strength has to be ENHANCED SHEAR, ORDINARY subdivided into small beam enhanced and Overall SHEAR CHECK IS PERFORMED. due to interaction of other distance of that beam in OTHERWISE PROVIDE ENSH AND beams, which result in RENSH parameter. RENSH PARAMETERS. performing only basic shear 2. Make subdivided beam check instead of Enhanced into continuous beam by Shear check for deep beams. applying ‘COMBINE’ parameter. DEPTH OF BEAM # __ SHALL This warning occurs only IS PREFERABLY BE LESS THAN THE 13920. 1/4TH OF CLEAR SPAN ASSUMING IT Use ‘COMBINE’ Command to TO BE SPANNING BETWEEN 7. illustrate STAAD that SUPPORTS. IF NOT, USE COMBINE Selected beams are PARAMETER. considered to be a *This Warning are not incorporated Continuous beam. in STAAD for the time being.
Section fails while designing section:
0.0 mm Nominal shear force exceeds tauc_max limit Provided Cross section is not Increase the Cross Section 8. adequate for applied loads. size. *This Warning are not incorporated in STAAD for the time being.
At 3.3 m Floor level, Lateral
SOFT STOREY DETECTED. Stiffness is less than 80% of AT 3.3 M IS SOFT ALONG GLOBAL X From IS 1893 Table 5, average of others storey AND Z DIRECTION. This refer to occurrence of 9. above. Vertical Irregularities in To check add ‘PRINT STORY *This Warning are not incorporated Structure. STIFFNESS’ from Analysis in STAAD for the time being. command. This NOTE refer to the beam SOME OF THE BEAMS CONNECTED are in straight line with respect TO THE COLUMN NO. ___ARE NOT to global axis. STAAD had PARALLEL TO GLOBAL AXES. ONLY Do manual calculation for 10. limited functions for Curved SHEAR FORCE FROM ANALYSIS WILL non-straight beam. beam and Non Straight line BE CONSIDERED FOR SHEAR DESIGN. beam. Only Flexure value will *Not Incorporated be consider.
CHECK FOR MINIMUM DIMENSION
OF COLUMN # 459 IS IGNORED AS From IS 13920 : 2016 Cl 7.1.1.a. The Cross Section of column PER CL 7.1.1 a) OF IS-13920:2016. Min Cross section of column does satisfy the criteria, 10. SOME OF THE BEAMS CONNECTED should satisfy the 20 times However the Warning rise. TO THE COLUMN ARE NOT diameter of bar in beam Due to Non straight beam is DESIGNED. passing through that column. interact with these column. *Not Incorporated
List of Improvement done in STAAD as follow,
S.NO. COMMENT(S) RESPONSE REMEDY
From Cl 7.8.4.2 of IS 1893
Modal Participation Masses should be sum of masses of all Changing the Mode(s) from 9. CUT OFF MODE SHAPE modes given is 90 % of total 60 to 12. seismic weight. This condition is acquired by just setting to 12.
Diverge the Seismic weights
Either Static or Dynamic IN REFERENCE LOAD CASE WHICH with respect to Individual analysis for seismic will assess 10. CONSIST OF SEISMIC WEIGHT directions and assign in their seismic weight or masses RESPECT TO DIRECTIONS. different reference load with respect to Directions. cases.
The Group Command cannot
APPLYING FLOOR LOAD USING 11. used properly, If assigned floor Created and Assigned. GROUP COMMAND beams are not a closed loop.
For IS 1893 : 2016, After
12. PRINT STORY DRIFT Response Spectrum Load case Added ‘CHECK STORY DRIFT’ Add ‘CHECK STORY DRIFT’