Professional Documents
Culture Documents
MobileDart Evolution MX8c
MobileDart Evolution MX8c
The wireless hand switch option consists of the following parts. Make sure that all these
parts are contained in the package.
This option does not include a battery for the wireless handswitch. Prepare it
separately beforehand.
Fig. 6-1
Fig. 6-2
n Wireless Holder
Fig. 6-3
Table 6-2
2 Remove the inside cover, both side covers, and top cover from the system.
"3.5 How to Open/Close Covers"
3 Open the cover under the FPD box and remove two hexagon cap screw to
remove cover B. And then fix only the removed nut again.
Fig. 6-4
4 Mount the wireless holder with two Phillips-head screws M3x16 and wire the
cable through a hole on the side of FPD box.
Fig. 6-5
Fig. 6-6
Fig. 6-7
Table 6-3
Recommend
No. Mode Function
value
Configure the pairing setting of wireless
1 Pairing Setting -
hand switch and wireless holder.
Touch Sensor
2 Modify the touch sensor setting. Invalid
Setting
Operation Limit
3 Set migration time to operation limit. 30 mins
Timer Setting
When reached to operation limit timer,
4 Buzzer Setting Invalid
switch ON/OFF buzzer setting.
Switch ON/OFF of handover mode setting
when using two wireless hand switches.
Handover
5 (The handover has been set to be invalid as Invalid
Setting
a factory setting. The setting change is not
needed.)
Setting mode is canceled after 3 minutes passes after entering to this mode.
Changed value will be discarded if the power of HOLDER turns off during setting
mode.
Fig. 6-8
Fig. 6-9
A cover of the wireless holder must be removed before access to function switch.
Remove the cover according to the following instructions.
Fig. 6-10
n Pairing Setting
Configure the pairing setting of wireless hand switch and wireless holder.
1 Set wireless hand switch to the wireless holder. LED1 turns ON when the power
is applied to the holder.
2 Keep pressing function switch1 (F1) of the holder until LEDs from LED2 to LED6
start blinking. (More than 5 seconds)
Fig. 6-11
5 LED2 starts blinking. Wireless holder starts searching for a wireless hand switch
that is in a state of pairing mode.
6 Take out wireless hand switch from the holder, and press and hold the paring
switch of wireless hand switch for more than 2 seconds within 1 minute since
the holder is set to the pairing mode. 6
Fig. 6-12
7 LED3 turns ON when the pairing is accomplished. LED4 and LED5 show touch
sensor status and operation limit timer status. (They will not turn ON if their
settings are not available.)
Fig. 6-13
The touch sensor is not used for this system. It should be set as invalid.
1 Set wireless hand switch to the wireless holder. LED1 turns ON when the power
is applied to the holder.
2 Press function switch1 (F1) of the holder until LEDs from LED2 to LED6 start
blinking. (More than 5 seconds)
Fig. 6-14
4 LED3 and LED6 turn ON. (Touch sensor function at the factory setting is valid)
Fig. 6-17
The operation limit timer has been set to 30 minutes as a factory setting. To
change the limit timer, follow the instruction below.
1 Set wireless hand switch to the wireless holder. LED1 is lighted when the power
is applied to the holder.
2 Keep pressing function switch1 (F1) of the holder until LEDs from LED2 to LED6
start blinking. (More than 5 seconds)
Fig. 6-18
4 LEDs from LED4 to LED7 indicate current setting. (The setting is set to 30 minutes
at factory setting)
Fig. 6-19
Fig. 6-20
Fig. 6-21
6
To return from the operation limit timer setting, set the wireless hand switch to
the wireless holder, and take out the wireless hand switch from the holder again.
n Buzzer Setting
The buzzer is not used for this system. It should be set as invalid.
1 Set wireless hand switch to the wireless holder. LED1 is lighted when the power
is applied to the holder.
2 Press function switch1 (F1) of the holder until LEDs from LED2 to LED6 start
blinking. (More than 5 seconds)
Fig. 6-22
4 LED5 and LED6 are lighted. (Buzzar function at the factory setting is valid)
Fig. 6-25
1 Turn OFF and then ON the key switch and restart the system.
2 Check that LED1 and LED3 are lighted after the system is started.
3 Check that LED6 is lighted after READY operation and LED7 is lighted after X-RAY
operation.
4 Check that the collimator lamp is lighted by pressing SW3 on the wireless hand
switch.
6
Fig. 6-26
Delete the pairing setting of wireless hand switch and wireless holder.
1 Set wireless hand switch to the wireless holder. LED1 turns ON when the power
is applied to the holder.
2 Keep pressing function switch1 (F1) of the holder until LEDs from LED2 to LED6
start blinking. (More than 5 seconds)
Fig. 6-27
3 Take out wireless hand switch from the holder, and press and hold the paring
switch of wireless hand switch for more than 10 seconds.
After 2 seconds since the pressing of the paring switch, RING LED of the wireless hand
switch blinks in yellow.
After 10 seconds, the deletion of paring setting is done, and the LED blinks in green.
Fig. 6-28
Fig. 6-29