Professional Documents
Culture Documents
(2013) AHU Kit - D201N (10 - 40HP) - DVM S - 131218 PDF
(2013) AHU Kit - D201N (10 - 40HP) - DVM S - 131218 PDF
MCM-D201N
MXD-A64K100E
1. Introduction
2. Function
3. Part introduction
4. Option setting
5. Changes from MXD-K***AN
OBJECTIVES
1. To understand Feature of AHU kit for 10~40HP
2. To understand the difference between MXD-K***AN & AHU kit for 10~40HP
※ Field supply
EEV connector
1 1 2 1 2 1 2
3 3 4
MXD-K***AN MCM-D201N
Return air E/A O/A Evap in sensor Supply air Return air E/A O/A Evap in sensor Supply air
Room sensor
Room sensor
Discharge sensor
H/X
H/X
Air Flow Air Flow
DVM S DVM+4
DVM S Water DVM+3
… …
Function Explanation
AHU Fan control Dry contact signal output when AHU is in Cool / Heat / Fan mode.
Dry contact signal input from AHU fan when fan is running.
AHU fan operation check
(Installation option setting required : 05 SEG21)
Defrost signal
Defrost signal off on off
3mins delay
(Installation option setting required : 05 SEG22)
Comp check & Error check Dry contact signal output ※connector must be supplied from field
Option setting
Salve AHU kit #3 Salve AHU kit #2
05 Seg24 Master Slave
[Room sensor] AHU kit AHU Kit
Slave - 0
PT1000 1 -
Current type 2 -
Wired R/C sensor 3 -
PT1000
or Wired remote
current type controller
Outdoor unit must have same address to use room temp sharing (OUD address : 00~15)
Each AHU kit must have different address regardless of ODU address to use one wired r/c
F3,F4
Slave AHU Kit : 01 ODU #1 address :05
F1,F2 CH : 00
Slave AHU Kit : 00
F1,F2
Slave AHU Kit : 10
R1,R2 CH : 01
12
10
15 11
8
9
1
2 3 4 5 6 7
① Power(220VAC) ② Fuse check ③ Current sensor(1,2) ④ H/X sensor connector ⑤ External contact input
PT1000 sensor(3,4,5) Eva In(1,2) (8,9)
Fan feedback(7,8) Eva Out(3,4)
The connector must be supplied from local market as no terminal block for below
- External contact
- Comp check & Error check
Sample
External Manufacture Comp Check Manufacture
contact Yeonho JST Error check Yeonho JST
SMH250-09 XHP-9 YH396-08V VHR-8N
Housing Housing
(Pitch 2.5mm) (Pitch 2.5mm) (Pitch 3.93mm) (Pitch 3.93mm)
Terminal YST025 SXH-001T-P0.6 Terminal YT396 SVH-21T-P1.1
Wire AWG 22~28 AWG 22~28 Wire AWG 16~24 AWG 16~22
External contact
* EEV wire : 7m
Filter
3) Regardless of the AHU kit HP setting, one AHU kit will be recognized as one indoor.
Evap Temp
room fan staring will be delay till 32℃ 32℃
26℃ 26℃
Evaporator get hot enough
ON ON
This won’t work when you don’t
use fan on signal to turn on the
FAN ON FAN OFF FAN ON FAN OFF
AHU Fan.
Capacity 2.5 / 5 / 7.5 / 10HP(separated model) 10 / 20 / 30 / 40HP(1 model with option setting)
EEV type
- Type : 103AT & Length : (10m) 2. Local supply : 4~20 mA (2wire type, -50℃~50℃)
Room
3. Internal sensor of Wired remote controller
sensor 2. Internal sensor of Wired remote controller
* sensor 1 or 2 must be installed even though room sensor
ex) MRW-WE10N setting(seg24) is 3(internal sensor of wired r/c usage).
- Wireless signal receiver applied on PCB - Wireless signal receiver applied on PCB
Feature
- Simple BMS connection - MIM0B14 function included
- Discharge temperature control (Comp & Error condition output, External contact)
3. Function setting
DVM S
DVM S Eco