Professional Documents
Culture Documents
Paper 1
Paper 1
4) You Notice that welder making pre heat above the level of WPS which one is affected..?
A) It increases the grain size of the boundary & removes hydrogen
B) It will give refined grain and remove hydrogen
C) It will increase the toughness and removes hydrogen
D) None of the above
8) WPS is….?
A) The documents available to welding inspector, NDT personnel
B) The document that contain relevant WPQR and wpqr is available to welding inspector, NDT personnel
C) Both A & B
D) None of the above
9) In NDT…?
A) In RT, 680 dia, 20mm thickness, DWDI is used
B) In RT, 70mm dia, 60mm Thickness, DWSI is used
C) In RT, 85 mm dia, 25 mm thickness, DWDI is used
D) A will be used by DWDI & DWSI
10) In RT ….?
A) Radiography will show lack of fusion as dark straight line in one side and other side bright
B) Radiography will show undercut as dark straight line in one side
C) Radiography will show lack of root penetration in one side bright and other side dark
D) None of the above
11) In contract, they said 20% RT and every one failure 2RT required and you would find one failure. What would you your action….?
A) You agree and you will show substituent the joint
B) You disagree and leave the Joint
C) You will ask more % of RT for Quality Assurance
D) None of the above
16) What would you consider while calibrating MIG Welding operation?
A) Amps, Volts, Travel Speed, Gas rate Flow
B) Amps, Volts, Travel Speed, Welding Consumable
C) Amps, Volts, Travel Speed, CTWD
D) None of the above
23) During Production welding, is welder allowed to adjust the welding current?
A) Toughness
B) Hardness
C) Re Only
D) Rm and Re
A) Curies
B) Kilo Volts
C) Joules
D) Electron Volts
A) After Welding
B) Before Welding
C) Before Welding and Before next pass
D) None of the Above
A) It is Important
B) Length and Position depends on material thickness and size
C) It always require preheat
D) None of the Above.
31) You noticed an excess penetration in a C-Mn welded country pipe line, what could be the reason...?
A) Wrong Electrode
B) Contaminated Electrode
C) Excess Root Grinding
D) Large Root Face
32) Which type of electrode is not best for Welding Cross country pipe line...?
A) Basic
B) Rutile
C) Cellulose
D) Iron powder
A) Arc Length
B) Arc Voltage
C) Flow rate
D) WFS
A) WFS is Constant
B) ARC length is Constant
C) Current is Constant
D) None of the above.
A) Chromium
B) Carbon
C) Manganese
D) Nickel
A) High Strength
B) Hardness
C) Toughness
D) Good Through Ductility
A) ASME Section V
B) ASME Section II
C) ASME Section IX
D) ASME Section VIII
44) Tensile Testing can determine...?
A) Notch Toughness
B) Hardness
C) %E
D) %E and %Z
46) A Fillet Weld has a design throat thickness of 6mm, what is the leg length Size....?
A) 8.4 mm
B) 5 mm
C) 8.5 mm
D) More information needed
47) What type of standard formed in a metal with low heat input during welding....?
A) Austenite
B) Pearlite
C) Bainite
D) Martensite
48) What is the heat input for MMA Welding of C-Mn with given variables 22V/250A, 250mm/min?
A) 1.056 KJ/cm
B) 1.056 KJ/mm
C) 1.56 J/mm
D) 1.56 J/cm
50) Which of the following statement for hydrogen control are true....?
A) MMA basic electrode will introduce more hydrogen than Agglomerated basic flux
B) TIG welding will introduce more hydrogen than Agglomerated Acid flux
C) MAG solid wire will introduce less hydrogen than fused basic flux
D) None of the Above.
A) B)
c) D)
56) In a SAW welding process, which could be reason for centre line crack....?
57) Hydrogen Induced Cold Cracking occurs 48-72 Hr after welding, what could be the reason...?
A) RT
B) PT
C) UT
D) MT
A) Butt weld
B) Fillet Weld
C) Seam weld
D) Spot weld