Download as pdf or txt
Download as pdf or txt
You are on page 1of 6

Product Description: AT-XXX27DT-096-TNEE - Maximum Span 800 m

Loading Conditions: NESC LIGHT


Ice Thickness 0 mm 0 in.
Wind Pressure 431 N/m^2 (95.5 km/hr) 9 psf (59.3 MPH)
Temperature -1.1 C 30 F
Safety Factor 0.73 N/m 0.1 lb/ft
Tension @ Maximum Span for 1.5 % Installation Sag
Short Term 2508 kg 5530 lb
Long Term 1763 kg 3886 lb
Specifications:
Maximum Span 800 m 2624 ft
Cable Weight 0.264 kg/m 0.178 lb/ft
Cable Diameter 18.2 mm 0.717 in
Installation Temp 20 C 68 F
Cable Modulus 946.3 kg/mm^2 1346.2 kpsi
Linear Expansion Coefficient 0.00000465 1 / C 0.00000258 1 / F
Estimated Break Load 4434 kg 9776 lb
Maximum Cable Length: Dependent on construction and/or fiber type
Singlemode 7,500 m 24,606 ft
62.5/125 Multimode 7,500 m 24,606 ft
No Loading @ Install Temperature: 20 C All Loading Conditions @ Temperature: -1.1 C
Span Sag Install Sag Tension Vertical Sag Tension Vertical Sag Horizontal Sag Angle
m m % kg % of Span kg m m Deg
50 0.8 1.50 110 0.7 274 0.3 1.0 72
100 1.5 1.50 220 0.8 476 0.8 2.3 72
150 2.3 1.50 330 0.8 656 1.2 3.7 72
200 3.0 1.50 441 0.9 824 1.7 5.3 72
250 3.8 1.50 551 0.9 983 2.3 6.9 72
300 4.5 1.50 661 0.9 1136 2.8 8.6 72
350 5.3 1.50 771 1.0 1285 3.4 10.4 72
400 6.0 1.50 881 1.0 1430 4.0 12.2 72
450 6.8 1.50 991 1.0 1571 4.6 14.0 72
500 7.5 1.50 1102 1.0 1710 5.2 15.9 72
550 8.3 1.50 1212 1.1 1847 5.9 17.8 72
600 9.0 1.50 1322 1.1 1983 6.5 19.8 72
650 9.8 1.50 1432 1.1 2116 7.2 21.7 72
700 10.5 1.50 1542 1.1 2248 7.8 23.7 72
750 11.3 1.50 1652 1.1 2379 8.5 25.7 72
800 12.0 1.50 1763 1.1 2508 9.2 27.8 72

The recommended maximum space potential at ADSS attachment point is 25 kV


Dead End Assembly: Slack Storage Devices: Not recommended for TR cables
PLP Dead-End: 2872206C1E1, Max. Tension: 7,500 lbs. (1135 kg) Note recommended for tracking Applications

Fixed Tangent Support (Line Angle Changes <= 20 deg & Spans <= 600 ft (183 m) Heliformed Suspension Units (Line angle changes<= 30 degrees):
PLP Dielectric Block Not recomended for Tracking Applications PLP: 43004991YC :Spans 1200ft to 2000ft (365m to 610m)
PLP: Aluminum Support: 4450104 Not recommended for TrackingApplications PLP: 4470204-S Aluminum Suspension with SRR rods, Max Span: 1200 ft (365m)

Suspended Support (Line Angle Changes <= 20 deg & Spans <= 600 ft (183 m) Vibration Dampers, see Application Note 812 for recommendations:
PLP: Aluminum Suspenion: 4450204-S Not recommended for TrackingApplications PLP Vibration Dampers: 50509862

Low Tension / Short Span Hardware: Down Lead Cushion & Abrasion Protector:
PLP Lite Tension DE not recomended for Tracking Applications PLP: 8003044, Add "H1" - Wood Attachment Kit & "LTC1" - Lattice Clamp Kit
PLP Lite Support not recomended for Tracking Applications PLP Abrasion Protector: PTG-0203 Length: 6 ft
PLP PGTTH Dead End: Not Available
Corona Coils recommended contact cable manufacturer
PLP: Sized to fit appropriate hardware, part numbers available upon request

Exclusive Use of OFS and Customer Defined Above

1
Product Description: AT-XXX27DT-072-TMIE - Maximum Span 800 m
Loading Conditions: NESC LIGHT
Ice Thickness 0 mm 0 in.
Wind Pressure 431 N/m^2 (95.5 km/hr) 9 psf (59.3 MPH)
Temperature -1.1 C 30 F
Safety Factor 0.73 N/m 0.1 lb/ft
Tension @ Maximum Span for 1.5 % Installation Sag
Short Term 2002 kg 4414 lb
Long Term 1294 kg 2854 lb
Specifications:
Maximum Span 800 m 2624 ft
Cable Weight 0.194 kg/m 0.13 lb/ft
Cable Diameter 15.6 mm 0.613 in
Installation Temp 20 C 68 F
Cable Modulus 1048.6 kg/mm^2 1491.7 kpsi
Linear Expansion Coefficient 0.00000392 1 / C 0.00000218 1 / F
Estimated Break Load 3591 kg 7919 lb
Maximum Cable Length: Dependent on construction and/or fiber type
Singlemode 7,500 m 24,606 ft
62.5/125 Multimode 7,500 m 24,606 ft
No Loading @ Install Temperature: 20 C All Loading Conditions @ Temperature: -1.1 C
Span Sag Install Sag Tension Vertical Sag Tension Vertical Sag Horizontal Sag Angle
m m % kg % of Span kg m m Deg
50 0.8 1.50 81 0.6 227 0.3 1.0 74
100 1.5 1.50 162 0.7 392 0.7 2.4 74
150 2.3 1.50 243 0.7 538 1.1 4.0 74
200 3.0 1.50 324 0.8 672 1.6 5.6 74
250 3.8 1.50 404 0.8 800 2.1 7.4 74
300 4.5 1.50 485 0.9 922 2.6 9.2 74
350 5.3 1.50 566 0.9 1040 3.1 11.1 74
400 6.0 1.50 647 0.9 1155 3.7 13.1 74
450 6.8 1.50 728 0.9 1267 4.3 15.1 74
500 7.5 1.50 809 1.0 1377 4.9 17.1 74
550 8.3 1.50 890 1.0 1485 5.4 19.2 74
600 9.0 1.50 971 1.0 1591 6.1 21.4 74
650 9.8 1.50 1052 1.0 1696 6.7 23.5 74
700 10.5 1.50 1133 1.0 1799 7.3 25.7 74
750 11.3 1.50 1213 1.1 1901 7.9 27.9 74
800 12.0 1.50 1294 1.1 2002 8.6 30.2 74

The recommended maximum space potential at ADSS attachment point is 25 kV


Dead End Assembly: Slack Storage Devices: Not recommended for TR cables
PLP Dead-End: 2872204C1E1, Max. Tension: 7,500 lbs. (1135 kg) Note recommended for tracking Applications

Fixed Tangent Support (Line Angle Changes <= 20 deg & Spans <= 600 ft (183 m) Heliformed Suspension Units (Line angle changes<= 30 degrees):
PLP Dielectric Block Not recomended for Tracking Applications PLP: 43009965YC :Spans 1200ft to 2000ft (365m to 610m)
PLP: Aluminum Support: 4450102 Not recommended for TrackingApplications PLP: 4470202-S Aluminum Suspension with SRR rods, Max Span: 1200 ft (365m)

Suspended Support (Line Angle Changes <= 20 deg & Spans <= 600 ft (183 m) Vibration Dampers, see Application Note 812 for recommendations:
PLP: Aluminum Suspenion: 4450202-S Not recommended for TrackingApplications PLP Vibration Dampers: 50509862

Low Tension / Short Span Hardware: Down Lead Cushion & Abrasion Protector:
PLP Lite Tension DE not recomended for Tracking Applications PLP: 8003043, Add "H1" - Wood Attachment Kit & "LTC1" - Lattice Clamp Kit
PLP Lite Support not recomended for Tracking Applications PLP Abrasion Protector: PTG-0203 Length: 6 ft
PLP PGTTH Dead End: Not Available
Corona Coils recommended contact cable manufacturer
PLP: Sized to fit appropriate hardware, part numbers available upon request

Exclusive Use of OFS and Customer Defined Above

2
Product Description: AT-XXX27DT-096-TMEE - Maximum Span 600 m
Loading Conditions: NESC LIGHT
Ice Thickness 0 mm 0 in.
Wind Pressure 431 N/m^2 (95.5 km/hr) 9 psf (59.3 MPH)
Temperature -1.1 C 30 F
Safety Factor 0.73 N/m 0.1 lb/ft
Tension @ Maximum Span for 1.5 % Installation Sag
Short Term 1836 kg 4048 lb
Long Term 1274 kg 2808 lb
Specifications:
Maximum Span 600 m 1968 ft
Cable Weight 0.255 kg/m 0.171 lb/ft
Cable Diameter 17.8 mm 0.7 in
Installation Temp 20 C 68 F
Cable Modulus 734.1 kg/mm^2 1044.3 kpsi
Linear Expansion Coefficient 0.00000678 1 / C 0.00000377 1 / F
Estimated Break Load 3283 kg 7240 lb
Maximum Cable Length: Dependent on construction and/or fiber type
Singlemode 7,500 m 24,606 ft
62.5/125 Multimode 7,500 m 24,606 ft
No Loading @ Install Temperature: 20 C All Loading Conditions @ Temperature: -1.1 C
Span Sag Install Sag Tension Vertical Sag Tension Vertical Sag Horizontal Sag Angle
m m % kg % of Span kg m m Deg
50 0.8 1.50 106 0.7 256 0.3 1.0 72
100 1.5 1.50 212 0.8 442 0.8 2.4 72
150 2.3 1.50 318 0.9 607 1.3 3.9 72
200 3.0 1.50 425 0.9 761 1.8 5.6 72
250 3.8 1.50 531 1.0 908 2.4 7.3 72
300 4.5 1.50 637 1.0 1050 3.0 9.1 72
350 5.3 1.50 743 1.0 1187 3.6 11.0 72
400 6.0 1.50 849 1.0 1322 4.2 12.9 72
450 6.8 1.50 955 1.1 1453 4.8 14.8 72
500 7.5 1.50 1061 1.1 1583 5.5 16.8 72
550 8.3 1.50 1168 1.1 1710 6.1 18.8 72
600 9.0 1.50 1274 1.1 1836 6.8 20.9 72

The recommended maximum space potential at ADSS attachment point is 25 kV


Dead End Assembly: Slack Storage Devices: Not recommended for TR cables
PLP Dead-End: 2872206C1E1, Max. Tension: 7,500 lbs. (1135 kg) Note recommended for tracking Applications

Fixed Tangent Support (Line Angle Changes <= 20 deg & Spans <= 600 ft (183 m) Heliformed Suspension Units (Line angle changes<= 30 degrees):
PLP Dielectric Block Not recomended for Tracking Applications PLP: 43009947YC :Spans 1200ft to 2000ft (365m to 610m)
PLP: Aluminum Support: 4450104 Not recommended for TrackingApplications PLP: 4470203-S Aluminum Suspension with SRR rods, Max Span: 1200 ft (365m)

Suspended Support (Line Angle Changes <= 20 deg & Spans <= 600 ft (183 m) Vibration Dampers, see Application Note 812 for recommendations:
PLP: Aluminum Suspenion: 4450204-S Not recommended for TrackingApplications PLP Vibration Dampers: 50509862

Low Tension / Short Span Hardware: Down Lead Cushion & Abrasion Protector:
PLP Lite Tension DE not recomended for Tracking Applications PLP: 8003044, Add "H1" - Wood Attachment Kit & "LTC1" - Lattice Clamp Kit
PLP Lite Support not recomended for Tracking Applications PLP Abrasion Protector: PTG-0203 Length: 6 ft
PLP PGTTH Dead End: Not Available
Corona Coils recommended contact cable manufacturer
PLP: Sized to fit appropriate hardware, part numbers available upon request

Exclusive Use of OFS and Customer Defined Above

3
Product Description: AT-XXX27DT-072-TLJE - Maximum Span 600 m
Loading Conditions: NESC LIGHT
Ice Thickness 0 mm 0 in.
Wind Pressure 431 N/m^2 (95.5 km/hr) 9 psf (59.3 MPH)
Temperature -1.1 C 30 F
Safety Factor 0.73 N/m 0.1 lb/ft
Tension @ Maximum Span for 1.5 % Installation Sag
Short Term 1446 kg 3188 lb
Long Term 925 kg 2039 lb
Specifications:
Maximum Span 600 m 1968 ft
Cable Weight 0.185 kg/m 0.124 lb/ft
Cable Diameter 15.1 mm 0.595 in
Installation Temp 20 C 68 F
Cable Modulus 792.5 kg/mm^2 1127.4 kpsi
Linear Expansion Coefficient 0.0000061 1 / C 0.00000339 1 / F
Estimated Break Load 2556 kg 5636 lb
Maximum Cable Length: Dependent on construction and/or fiber type
Singlemode 7,500 m 24,606 ft
62.5/125 Multimode 7,500 m 24,606 ft
No Loading @ Install Temperature: 20 C All Loading Conditions @ Temperature: -1.1 C
Span Sag Install Sag Tension Vertical Sag Tension Vertical Sag Horizontal Sag Angle
m m % kg % of Span kg m m Deg
50 0.8 1.50 77 0.6 208 0.3 1.1 74
100 1.5 1.50 154 0.7 357 0.7 2.6 74
150 2.3 1.50 231 0.8 488 1.2 4.2 74
200 3.0 1.50 308 0.8 610 1.7 6.0 74
250 3.8 1.50 385 0.9 726 2.2 7.9 74
300 4.5 1.50 463 0.9 837 2.7 9.9 74
350 5.3 1.50 540 0.9 944 3.3 11.9 74
400 6.0 1.50 617 1.0 1048 3.9 14.0 74
450 6.8 1.50 694 1.0 1150 4.5 16.2 74
500 7.5 1.50 771 1.0 1251 5.1 18.4 74
550 8.3 1.50 848 1.0 1349 5.7 20.6 74
600 9.0 1.50 925 1.1 1446 6.4 22.9 74

The recommended maximum space potential at ADSS attachment point is 25 kV


Dead End Assembly: Slack Storage Devices: Not recommended for TR cables
PLP Dead-End: 2872103C1E1, Max. Tension: 4,000 lbs. (1135 kg) Note recommended for tracking Applications

Fixed Tangent Support (Line Angle Changes <= 20 deg & Spans <= 600 ft (183 m) Heliformed Suspension Units (Line angle changes<= 30 degrees):
PLP Dielectric Block Not recomended for Tracking Applications PLP: 43009945YC :Spans 1200ft to 2000ft (365m to 610m)
PLP: Aluminum Support: 4450102 Not recommended for TrackingApplications PLP: 4470202-S Aluminum Suspension with SRR rods, Max Span: 1200 ft (365m)

Suspended Support (Line Angle Changes <= 20 deg & Spans <= 600 ft (183 m) Vibration Dampers, see Application Note 812 for recommendations:
PLP: Aluminum Suspenion: 4450202-S Not recommended for TrackingApplications PLP Vibration Dampers: 50509862

Low Tension / Short Span Hardware: Down Lead Cushion & Abrasion Protector:
PLP Lite Tension DE not recomended for Tracking Applications PLP: 8003043, Add "H1" - Wood Attachment Kit & "LTC1" - Lattice Clamp Kit
PLP Lite Support not recomended for Tracking Applications PLP Abrasion Protector: PTG-0203 Length: 6 ft
PLP PGTTH Dead End: Not Available
Corona Coils recommended contact cable manufacturer
PLP: Sized to fit appropriate hardware, part numbers available upon request

Exclusive Use of OFS and Customer Defined Above

4
Product Description: AT-XXX27DT-096-TLDE - Maximum Span 400 m
Loading Conditions: NESC LIGHT
Ice Thickness 0 mm 0 in.
Wind Pressure 431 N/m^2 (95.5 km/hr) 9 psf (59.3 MPH)
Temperature -1.1 C 30 F
Safety Factor 0.73 N/m 0.1 lb/ft
Tension @ Maximum Span for 1.5 % Installation Sag
Short Term 1173 kg 2586 lb
Long Term 805 kg 1776 lb
Specifications:
Maximum Span 400 m 1312 ft
Cable Weight 0.242 kg/m 0.162 lb/ft
Cable Diameter 17.3 mm 0.679 in
Installation Temp 20 C 68 F
Cable Modulus 479.5 kg/mm^2 682.1 kpsi
Linear Expansion Coefficient 0.00001164 1 / C 0.00000647 1 / F
Estimated Break Load 2018 kg 4450 lb
Maximum Cable Length: Dependent on construction and/or fiber type
Singlemode 7,500 m 24,606 ft
62.5/125 Multimode 7,500 m 24,606 ft
No Loading @ Install Temperature: 20 C All Loading Conditions @ Temperature: -1.1 C
Span Sag Install Sag Tension Vertical Sag Tension Vertical Sag Horizontal Sag Angle
m m % kg % of Span kg m m Deg
25 0.4 1.50 50 0.6 134 0.2 0.5 72
50 0.8 1.50 101 0.7 229 0.4 1.1 72
75 1.1 1.50 151 0.8 314 0.6 1.9 72
100 1.5 1.50 201 0.8 392 0.8 2.6 72
125 1.9 1.50 252 0.9 466 1.1 3.5 72
150 2.3 1.50 302 0.9 537 1.4 4.3 72
175 2.6 1.50 352 1.0 606 1.7 5.2 72
200 3.0 1.50 403 1.0 673 2.0 6.2 72
225 3.4 1.50 453 1.0 739 2.3 7.1 72
250 3.8 1.50 503 1.0 804 2.6 8.1 72
275 4.1 1.50 554 1.0 867 2.9 9.0 72
300 4.5 1.50 604 1.1 930 3.2 10.0 72
325 4.9 1.50 654 1.1 992 3.5 11.0 72
350 5.3 1.50 705 1.1 1053 3.8 12.1 72
375 5.6 1.50 755 1.1 1113 4.2 13.1 72
400 6.0 1.50 805 1.1 1173 4.5 14.1 72

The recommended maximum space potential at ADSS attachment point is 25 kV


Dead End Assembly: Slack Storage Devices: Not recommended for TR cables
PLP Dead-End: 2872105C1E1, Max. Tension: 4,000 lbs. (1135 kg) Note recommended for tracking Applications

Fixed Tangent Support (Line Angle Changes <= 20 deg & Spans <= 600 ft (183 m) Heliformed Suspension Units (Line angle changes<= 30 degrees):
PLP Dielectric Block Not recomended for Tracking Applications PLP: 43004965YC :Spans 1200ft to 2000ft (365m to 610m)
PLP: Aluminum Support: 4450104 Not recommended for TrackingApplications PLP: 4470203-S Aluminum Suspension with SRR rods, Max Span: 1200 ft (365m)

Suspended Support (Line Angle Changes <= 20 deg & Spans <= 600 ft (183 m) Vibration Dampers, see Application Note 812 for recommendations:
PLP: Aluminum Suspenion: 4450204-S Not recommended for TrackingApplications PLP Vibration Dampers: 50509862

Low Tension / Short Span Hardware: Down Lead Cushion & Abrasion Protector:
PLP Lite Tension DE not recomended for Tracking Applications PLP: 8003044, Add "H1" - Wood Attachment Kit & "LTC1" - Lattice Clamp Kit
PLP Lite Support not recomended for Tracking Applications PLP Abrasion Protector: PTG-0203 Length: 6 ft
PLP PGTTH Dead End: Not Available
Corona Coils recommended contact cable manufacturer
PLP: Sized to fit appropriate hardware, part numbers available upon request

Exclusive Use of OFS and Customer Defined Above

5
Product Description: AT-XXX27DT-072-TNCB - Maximum Span 400 m
Loading Conditions: NESC LIGHT
Ice Thickness 0 mm 0 in.
Wind Pressure 431 N/m^2 (95.5 km/hr) 9 psf (59.3 MPH)
Temperature -1.1 C 30 F
Safety Factor 0.73 N/m 0.1 lb/ft
Tension @ Maximum Span for 1.5 % Installation Sag
Short Term 937 kg 2065 lb
Long Term 576 kg 1269 lb
Specifications:
Maximum Span 400 m 1312 ft
Cable Weight 0.173 kg/m 0.116 lb/ft
Cable Diameter 14.6 mm 0.573 in
Installation Temp 20 C 68 F
Cable Modulus 587.5 kg/mm^2 835.7 kpsi
Linear Expansion Coefficient 0.00000933 1 / C 0.00000519 1 / F
Estimated Break Load 1468 kg 3236 lb
Maximum Cable Length: Dependent on construction and/or fiber type
Singlemode 11,600 m 38,058 ft
62.5/125 Multimode 8,000 m 26,247 ft
No Loading @ Install Temperature: 20 C All Loading Conditions @ Temperature: -1.1 C
Span Sag Install Sag Tension Vertical Sag Tension Vertical Sag Horizontal Sag Angle
m m % kg % of Span kg m m Deg
25 0.4 1.50 36 0.5 110 0.1 0.5 75
50 0.8 1.50 72 0.6 189 0.3 1.2 75
75 1.1 1.50 108 0.7 257 0.5 1.9 75
100 1.5 1.50 144 0.7 320 0.7 2.8 75
125 1.9 1.50 180 0.8 380 1.0 3.7 75
150 2.3 1.50 216 0.8 437 1.2 4.6 75
175 2.6 1.50 252 0.9 492 1.5 5.5 75
200 3.0 1.50 288 0.9 545 1.8 6.5 75
225 3.4 1.50 324 0.9 597 2.0 7.5 75
250 3.8 1.50 360 0.9 648 2.3 8.6 75
275 4.1 1.50 396 0.9 698 2.6 9.6 75
300 4.5 1.50 432 1.0 747 2.9 10.7 75
325 4.9 1.50 468 1.0 795 3.2 11.8 75
350 5.3 1.50 504 1.0 843 3.5 12.9 75
375 5.6 1.50 540 1.0 890 3.8 14.1 75
400 6.0 1.50 576 1.0 937 4.1 15.2 75

The recommended maximum space potential at ADSS attachment point is 25 kV


Dead End Assembly: Slack Storage Devices: Not recommended for TR cables
PLP Dead-End: 2872102C1E1, Max. Tension: 4,000 lbs. (1135 kg) Note recommended for tracking Applications

Fixed Tangent Support (Line Angle Changes <= 20 deg & Spans <= 600 ft (183 m) Heliformed Suspension Units (Line angle changes<= 30 degrees):
PLP Dielectric Block Not recomended for Tracking Applications PLP: 43009945YC :Spans 1200ft to 2000ft (365m to 610m)
PLP: Aluminum Support: 4450101 Not recommended for TrackingApplications PLP: 4470202-S Aluminum Suspension with SRR rods, Max Span: 1200 ft (365m)

Suspended Support (Line Angle Changes <= 20 deg & Spans <= 600 ft (183 m) Vibration Dampers, see Application Note 812 for recommendations:
PLP: Aluminum Suspenion: 4450201-S Not recommended for TrackingApplications PLP Vibration Dampers: 50509862

Low Tension / Short Span Hardware: Down Lead Cushion & Abrasion Protector:
PLP Lite Tension DE not recomended for Tracking Applications PLP: 8003043, Add "H1" - Wood Attachment Kit & "LTC1" - Lattice Clamp Kit
PLP Lite Support not recomended for Tracking Applications PLP Abrasion Protector: PTG-0203 Length: 6 ft
PLP PGTTH Dead End: Not Available
Corona Coils recommended contact cable manufacturer
PLP: Sized to fit appropriate hardware, part numbers available upon request

Exclusive Use of OFS and Customer Defined Above

You might also like