Professional Documents
Culture Documents
TRIO Poster US1 en
TRIO Poster US1 en
TRIO
Shaft Panel TSE 270,
Item no. 105523
• Only use as many ties as are necessary. Unused tie holes
must be sealed with plugs Ø 20/24, item no. 030300.
WDA 10
Shaft Panel TSE 120,
Item no. 105524
The panel formwork with the BFD coupler system Without exception, all current safety regulations must be observed
in those countries where our products are used.
GSV
Since production began, TRIO has always fulfilled the
highest requirements regarding the formwork evenness.
BFD – for standard panel joints – on external corners – with filler timber up to 100 mm – for timber extensions TRIO shaft panel TSE in a When striking, lever crowbar For rectangular shafts, shorten Test report available
raised position. upwards. the chains on the longitudinal on request.
sides. This ensures that all shaft
panels are evenly loaded.
Filler timber
6. T-Junctions 8. Wall Connections 1. Panel Connections 4. Oblique Angles
1. With 270 x 240
72
Basic rules for T-Junctions TRIO articulated corner TGE – Internal formwork: External formwork:
M
Wall thicknesses 180 – 400 mm and for internal and external corners alike. with TR 60 or TR 30 panels and with multi-panel TRM 72 and
TR
TAR 85 TAR 85
600 mm 270 x 240 articulated corners articulated corners TRM 72 TGE TAR
85 TRM 72 TGE
60
E
TRM
TG
7 2
External formwork: with panel TR 90 Internal panel connection: External panel connection:
E
TG
Internal formwork: with TRIO Corner TE 4 BFD couplers 2 compensation walers TAR 85, 60 TGE 30 TGE
Tie details
85
270 x 240 6 BFD couplers 60
72
165°
TAR
75°
2,70 m
TRM
Articulated Corner ø 24
30
wall thickness compensation WDA 5, 2. With WDA or timber TGE 270
WDA 6 or timber infills.
TRM 72
30 30 TRM 72 TGE
TA
30 30 R
Filler timber TR 85
M
72
60 TGE
150° 60
Filler timber
Filler timber
2 pc. Alignment Coupler BFD
TE 3. With TRM 72 Item no. 023500 ≥ 75°
TE
WDA 5 (6) for 2.70 m panel heights. TAR 85
TRM 72 TGE
(18)
(36)
TAR 85
20
WDA 5 (6)
35
90
90
TA TR
R M
TE Corner TGE 120 60 TGE
85 7
Item no. 023300
TA TRM
60 TGE
R8 7
2
TRM 72 135°
5 2
120°
60
60
1. With 270 x 240 2. With TRM 72 3. With TR 30 4. With WDA or timber infills
WDA 5/6
TRM 72
TRM 72
2. Length Compensation
30
30
WDA 5 (6)
TRIO Column
TAR 85
TAR 85
270 x 240
270 x 240
Simple and fast solution. Cost-effective solution. Optimal visible surface solution. With panels for walls and columns
TE
With timber, or timber and formlining, With filler plates from 60 – 360 mm. With formlining and filler support. Can be used as column panels for
TE and BFD alignment coupler up to LA 270, Item no. 023170 TPP, Alu 270, Item no. 101813 cross-sections of up to 750 x 750 mm.
100 mm. LA 120, Item no. 023270 TPP, Alu 120, Item no. 101823 Used in the wall as “standard”
(24)
90
25
WDA 5
40
TE
Permissible fresh concrete pressure
TE 100 kN/m2.
TRS 90
TRS 90
max.
TRM 72
TE 60 750 x 750
TRS 90
90
TE
TE
TE TE TRS 90
120
60
30
90
TE TE
72
TE
TRM 72
TRM 72
Corner construction:
7. Stopend Formwork 5. Wall Offsets 3. Corners 600 mm wall thickness
Perm. fresh concrete pressure 60 kN/m²
Using the TRIO MT/MTF stopend panel with continuous reinforcement, with or Up to max. 200 mm Basic rules for corners 20 25 30 Note:
without water bars. Wall thicknesses 180 – 400 mm Along the length L of 2.25 m,
60
Lower TAR 85 to be (18) (24)
fixed from below 3 BFD alignment couplers are
30 Adaptation to wall thickness using wall required per panel joint.
MT centre part, MTF centre part,
thickness compensation WDA 5, WDA 6
without water bar with water bar Filler timber
TAR 85
or timber infills
20 cm
max.
WDA 5 (6)
2 WDA 5 (6)
Internal formwork: External formwork:
30
With TRIO Corner TE With TR 72 panels or TRM 72 and TR 60
L
Timber Connection:
Connection: 5 BFD alignment couplers for h = 2.70 m
Additional BFD for 120 Hook tie DW 15/400 2 BFD alignment couplers for h = 2.70 m TE
60
TAR 85
mm offsets upwards TE
72
72
72
TE
270 x 240
270 x 240
Compensation
Waler TAR 85
L
TRM 72
TRM 72
Note:
86 cm
max.
Timber supplied by
20 cm
min.
or 5 cm.
60 TE
Stopend tie TE
TAR 85
TE
72
80
72
TRM 72
TAR 85
Push-Pull Props and Kicker Braces Transportation and storage Height Extensions Extension Units (Steel) Tie hole position (advancing form)
Push-pull props and kickers to brace Subsequent push-pull props according For assembly of Stacking Device TRIO, galv. Lifting Hook TRIO Lifting Gear Combi-2 TRIO Alignment couplers and all-round Extensions up to max. 8.10 m high Formwork should be assembled Compensation Waler TAR 85
the formwork and bearing the wind- to the table. The connection at the base plates. Perm. load 500 kg/piece. Maximum lifting capacity of 1.5 t, Permissible load 2.9 t at 45° spread of the lifting gear. struts ensure that extensions with (3 panels at 2.70 m) can be assembled to its full height on the ground! Alignment Coupler BFD
load are to be arranged as shown on TRIO panel takes place with the TRIO Ankerschraube PERI MMS 20 x 130
Art. Nr.: 103606 For safe stacking of 5 TRIO panels of at a crane sling angle of max. 30°. The pins are used to move stacks of panels located on the ground. TRIO are simple and easy. as one unit.
the adjacent diagram and table. prop connector. any size. Always use in pairs! TRIO lifting hooks or TRIO stacking devices are attached to the
PERI anchor bolt
Zur Befestigung von Richtstützen, Technische Daten
Abspannungen bei SKYDECK Bühnen
The first panel must always be braced Fixing to the ground slab is done with load hook. 270 240 120 90 72 60 30 TE TGE TGE TGE
oder auskragenden Deckentischen ist Ankerlänge L
W eigh
MMS 20 x 130
Verankerungstiefe h ≥
Befestigungssystemen.
Bohrtiefe h ≥
id
Bruchlastmitte
Betonfestigkeit
Follow Instructions for Use! Follow Instructions for Use! Follow Instructions for Use!
Table for PERI push-pull props and kicker braces
β
240 / 270
Sicherheitsbeiwert s = 4
Sicherheitsbeiwert s = 4
Fig. 1 Fig. 2
270
PERI GmbH
Schalung Gerüst Engineering
240
max. Width of influence [m] 3,53 2,73 2,19 1,82 1,58 1,42 1,93 1,67 1,49 1,35 Lifting Gear Combi-2 TRIO
Item no. 044760
Actual prop load FRS [kN] at FRS1 9,4 11,3 11,3 11,3 Fig. 2 PERI Paletten und
Stapelrungen
TRIO Versetzhaken 1,5t
Art.-Nr. 023690
TRIO Kombigehänge-2
Art.-Nr. 044760
9,7 9,7 9,8 9,8 9,8 9,6
max. prop spacing FRS2 9,5 8,5 9,3 10,1 Bedienungsanleitung Bedienungsanleitung Bedienungsanleitung
30
60
2,1 2,3 2,2 2,2 2,3 2,6 2,6 2,3 2,1 1,9
[kN] at max. prop spacing
300
y = *Top connection point [m] 2,0 2,0 y1 1,5 1,8 1,8 1,8 Fig. 1
1,0 1,2 1,5 1,8
from top of formwork y2 4,5 5,5 6,2 6,9 Ausgabe 05/2007 Ausgabe 05/2007 Ausgabe 05/2007
60
the foot of the push-pull-prop for the given width of influence. Stacking Device TRIO Lifting Hook TRIO
60° 60°
Item no. 023390 Item no. 023690
270
240
th
ig
ht
270
240
30
120
120
390
en
c e1
.35
m
Foundations
Weight 329,00 kg 162,00 kg 115,00 kg 87,70 kg 60,60 kg 97,60 kg 69,80 kg 103,00 kg 94,80 kg flu
Scaffold Bracket of in Single foundations with
TRG 80 Item no. 023670 dth
wi
60
Guardrail Post
120
HSGP
120
1,00
Item-no. 034580
450
1,00
90
TAE TAM 72
270
Foundation Strap
240
Concreting Platform 120 x 270 Scaffold Bracket TRG 100/112 Strip foundations with
TRA 270
Item no. 022950 Item no. 023590 Foundation Tie Clamp Item no. 023010 Stop rail
Perforated Foundation Tie Item no. 023020
A single platform unit is only 320 mm Top Tie Bracket-2 AH Item no. 023630
high when folded. Each additional unit
adds only 170 mm in height. 13 con-
60
m 2
2,43 1,62 0,81 1,62 1,94
ing height of a truck.
240
Foundation
270
240
Tie Clamp
17
Accessories: Perforated
32
Poster
Edition 02/2010
The optimal System for every
Project and every Requirements
PERI GmbH
Formwork Scaffolding Engineering
P.O. Box 1264
89259 Weissenhorn
Germany
Tel. +49 (0)7309.950-0
Fax +49 (0)7309.951-0
info@peri.com
www.peri.com