The document provides instructions for using a digital voltage tester. It describes how to use the direct test button to measure voltages between 12-250 volts by touching the sensing tip to wires. It also describes how to use the break-point test button to detect break points in live wiring by running the tip along wires and monitoring for changes in the voltage reading. Safety warnings are provided, such as not getting the tester wet or attempting to disassemble it.
The document provides instructions for using a digital voltage tester. It describes how to use the direct test button to measure voltages between 12-250 volts by touching the sensing tip to wires. It also describes how to use the break-point test button to detect break points in live wiring by running the tip along wires and monitoring for changes in the voltage reading. Safety warnings are provided, such as not getting the tester wet or attempting to disassemble it.
The document provides instructions for using a digital voltage tester. It describes how to use the direct test button to measure voltages between 12-250 volts by touching the sensing tip to wires. It also describes how to use the break-point test button to detect break points in live wiring by running the tip along wires and monitoring for changes in the voltage reading. Safety warnings are provided, such as not getting the tester wet or attempting to disassemble it.
The Digital Voltage Tester: Measuring the Voltage: Testing for Break-points in Live Wiring: Testing for Live
or Break-points in Live Wiring: Testing for Live Wires or Contacts:
Touch and hold the Direct Test button on the front Touch and hold the Break-point Test button on the top Touch and hold the Break-point Test button on the top of the Digital Voltage Tester. Next hold the sensing of the Digital Voltage Tester. Next hold the sensing tip of the Digital Voltage Tester. Next hold the sensing tip tip of the voltage tester against the bare wire or of the voltage tester against the wiring to be tested. of the voltage tester against the bare wire or contact Break-point Test button contact where you wish to measure the voltage. Hold it at the closest position to the power source that you wish to test. such that the tester displays the following result*: DIGITAL VOLTAGE TESTER If the wire or contact is live, the light on the front of the tester will illuminate. If the wire or contact is not live or Instruction Manual Direct Test button Live wire found at this point of a low voltage, the light will not illuminate.
Touch and hold here
Live-wire light Touch and hold here Live wire Touch and hold here
LCD voltage display
The tester will display one of the following results: Illuminate if wire is live
No voltage measured at this
point-wire is not live.
The measured voltage at
Run the sensing tip along the length of the wire. this point is about 12 volts. When the display changes to show the result as SAFETY WARNINGS: below, you have found a possible break-point in The measured voltage at the wiring. Do not press both buttons at the same time this point is about 36 volts. while testing. No voltage measured at Do not get the tester wet. The measured voltage at this point. Do not attempt to disassemble this product. this point is about 55 volts. Keep out of the reach of children. To confirm the break-point position, repeat the test Do not use if tester is rusted or damaged. Distributed By: Apollo Tools, Ltd. to see if the display changes at the same position. This tester is not suitable for checking DC 255 Clapp Road - Suite 200 The measured voltage at batteries. Scituate, MA 02066 USA this point is about 110 volts. Do not wear gloves when using this tester. No batteries required Sensing Tip *Note: This tester can only test live wires. In some Visit our website at: www.apollotools.com Contact us at: sales.usa@apollotools.com wiring, the power wires run alongside each other. This tester is not 100% accurate. Use a Non-contact voltage testing Or phone us at: 1-866-591-4749 The measured voltage at Make sure you test both sides of the cable to find multimeter for an accurate voltage reading. Detect break-points in wiring International Sales: sales@apollotools.com Made in China this point is 220 to 250 volts. the live wire to test. Measure 12V-250V AC and DC