Professional Documents
Culture Documents
JCO WiFi NVR Kit User Manual 20160419
JCO WiFi NVR Kit User Manual 20160419
JCO WiFi NVR Kit User Manual 20160419
User Manual
The manual shows the method for hard disk installation and interface
operation.
Content may be modified and updated based on new function.
The manual and Picture is for reference, please operate it based on the actual
products. Please contact our assistant or technical for the latest version if
there is any change on products.
The components or file mentioned in the file is for guidance, please refer to
packing list inside for the detailed configuration.
The model for battery is CR2032 lithium battery, explosion may occur if using
other type. Do not put it in fire or household garbage. Please dispose it under
the guide of local Laws and regulations.
2. Products Introduction
The wireless NVR Kit use LINUX operation system with stable operation,
support wireless network video input, 1.3MP max for real time viewing, video
coding and playback. H.264 ensures high quality Picture and low bite coding
rate and function for video viewing and recording.
The wireless NVR Kit can operate separately in LAN,or connecting to Internet
in WAN, match with professional video surveillance platform to ensure the
strong ability for remote monitoring. With the latest wireless network
2
technology ensures easy installation, which can widely used in family, shop,
office and villa,etc.
2.3. Specifications
3
Main Processor HI3520D HI3535
Operation System Embedded LINUX
System
System Resource support multi-channel recording, playback, multi-user
network operation and USB backup
Operation Interface 24 bit true color graphical operation interface, support
mouse operation
Picture Display 4/ 1 9/ 4/ 1
4
3. Installation
3.2.1. Front-panel
5
① POW: Power supply indication
② HDD: Hard disk indication
③ REC: Recording indication
3.2.2. Back-Panel
1 Antenna
2 Network port: 3 LAN ports for reserved, 1 WAN port: connect to
Internet
3 VGA output
4 HDMI output
5 USB interface
6 Power supply : DC12V
The WiFi NVR support hard disk inside installation, 1 pc 4T hard disk max.
Please use professional hard disk to ensure continues and stable recording.
Steps are below:
6
Attention: Make sure power is off during installation.
7
6 Install the NVR cover, fix it with 4pcs M3*6 screws, and change NVR
antenna to the direction as picture 2.3.1-6 shows.
8
3.3.3. Placement of WiFi IPC
1 Place WiFi IPC within signal covered area, and connect to 12V power
supply.
2 Picture will show on monitor after 1 minutes when power turn on.
3 If no Picture, please shorten the distance between IPC and NVR.
4 Placement of Wireless IPC
The shape of wireless NVR signal coverage is a ball, performance will be
better when NVR antenna and IPC antenna at the same height, if can not,
please make the wireless IPC keeping parallel or tangent with wireless NVR,
do not keep IPC antenna point to NVR antenna directly.
4. Function Instruction
4.1. Log in
Connect power supply, device start work, and shows “ Tip Guide.” Log in
9
interface can show if choose 【Quit】. as picture 3.1-1 shows:
Picture 3.1-1
Please log in before make any operation, functions may different because
of user permission. Default user name is “admin” and password is empty.
“admin” is the default superuser permission, as picture 3.1-2 shows:
Attention: For safely reasons, please modify user name and password in
【System setup】→【User】.(Detail info can check in 3.9.5)
Picture 3.1-2
After log in, Picture will show on screen. States of date, time, channel, audio,
10
record , alarm information will show on each screen.
Audio on Audio off Record on
Function declaration: system will start Tip Guide automatically after log in. For
stable operation, users can follow the guide to set data.
1 P2P setting
Click 【Enable】, the device ID is for remote monitoring. Click【No longer
prompt】 to stop Tip Guide when log in next time. After the operation, click
【Next】. as picture 3.2-1 shows:
Picture 3.2-1
2 Wirenet Setting
11
Users can choose to setting IP address automatically or manually, and
setting the data of Subnet, gateway, then click【Next】. as picture 3.2-2 shows.
Picture 3.2-2
3 Device adding
When shows the interface below, NVR will match code automatically with IPC,
and will list device information in【Dev Has Searched】, users can add/ edit/
delete WiFi IPC in this interface. click【Next】to continue Tip Guide. as picture
3.2-3 shows.
Picture 3.2-3
Attention: Only finished code matching can WiFi NVR search and add WiFi
12
IPC. All the device has matched code in factory.
4 Hard Disk Management
Users can see hard disk information in this interface. For disk formatting,
choose the target hard disk firstly, then click【Format】, format will be finished
a few minutes later. When finished,【Next】 to continue Tip Guide. as picture
3.2-4 shows.
Picture 3.2-4
5 Record Setting
There are 6 periods for recording, users can set week, period information.
Recording type can choose from normal/ motion or alarm. Please click
【Save】after setting, and then click 【Finish】.as picture below.
13
4.3. Net channel setting
Function declaration: users can search/ add/ delete WiFi IPC in this interface.
Picture 4.3-1
Picture 3.3-2
Attention: Make sure wireless signal is good between IPC and NVR, and
distance is not far away. When device can not found in list after matching code,
please check whether finished matching code, and adjust the distance
between IPC and NVR.
15
4.3.3. Add all device
Users can click 【Add All】to add all the device in list.
Users can input channel information manually, like IP address, channel, user
name, password, and then click 【Enable】, then the device will add to the
target channels. as picture 3.3-3 shows.
Picture 3.3-3
16
then match code with new device.
2
Remove all device: Remove all device with one-key press. When
NVR ESSID and password changed, or using new WiFi NVR, users need to
remove all device in the list, and set code matching data with WiFi IPC.
Users can set IPC information like IP address/ port/ user name/ password
IP protocol.
Step 1: In【Net channel】, choose a device in 【Dev Has Add】.
Step 2: Click the device, then users can modify IPC information.
Function declaration: When device used for Network monitoring or open P2P
function, users need to set network data first. Default IP address is
192.168.1.218.
Step 1: Choose 【 Wirenet setting 】 in main menu, or 【 System setup 】 →
【Network setting】→【Wirenet Setting】
Step 2: Set Network data. Users can modify IP address/ Subnet/ Gateway/
DNS information. Users can also open【DHCP】, which means gain IP address
automatically. Steps as below:
【Net card】: Default net card is 1.
【IP address】: The IP address WiFi NVR. Users can input the IP address in
website and can view the performance on web.
【Subnet】: Default subnet is 255.255.255.0, no need to modify.
【Gateway】: Gateway should be matched with IP address when it modified.
【Main DNS】:Domain name system, make the domain name input IP address.
The address is offered by your network operators, the address will come into
use when finished setting.
17
【Sub DNS】:Reserved DNS to ensure stable network connecting.
【MAC】: Physical address of device, can not be changed.
【DHCP】: Device gain the IP address automatically, users can turn on the
function if do not know how to set IP address.
When Finished setting, click【Save】, chose【cancel】to view the Picture.
Users also can press【Default】to set data to factory default. as picture 3.4-1
shows.
Picture 3.4-1
When opened HDCP function, users can not modify IP address
automatically.
Function declaration: Users can set data of SSID/ password/ WiFi channel,
and also can see the device information.
Choose 【WiFi Setting】in main interface.
【Connected】: Indicate connected device quantity, MAC address and rate.
【MAC addr】: MAC address of WiFi module can not be modified.
【SSID】: Users can set the SSID information.
18
【Password】: Users can set the password.
Picture 3.5-1
Advance Set
【Reset WiFi】: Used for resetting NVR network setting, include wireless
/wirenet and PPPOE data.
【WiFi Channel】: Users can choose the suitable WiFi channel per the using
environment ( the default channel is “auto”, users can choose the suitable
channel based on Local laws and regulations)
19
Picture 3.5-2
4.7. Playback
Picture 3.7-1
21
Icon Introduction
Single channel
4 channel playback Audio closed
playback
Picture 3.8-1
22
4.9. System Setup
Picture 3.9-1
24
4.9.3. Record
Record setup
【Period】: Max support 6 periods unrepeatable.
【Video type】: Three 3 types for option: Normal (timing recording), Motion
(motion detection recording), Alarm(alarm or IO alarming recording).
User can click 【Copy】to copy current channel video parameters to other’s or
click【Default】for default setting.
Click 【Apply】to save the data, and click【Quit】to return and check. as picture
3.9.3-1 shows.
Picture 3.9.3-1
Disk management
User can confirm 【disk No.,】【Status】, 【Total Space】, 【Free space】
and 【type】after installed hard disk. as picture 3.9.3-2 shows.
25
Picture 3.9.3-2
Format: click 【Ok】to erase all the information, click 【Cancel】 to quit format.
Picture 3.9.3-3
Backup
26
The video file in NVR can be backuped to external storage device, storage
device (like USB flash disk or removable hard disk) need to be installed before
backup. Users can view video file based on external device independently
when finished backup.
【Detection】: Detecting external storage device connected on NVR, like USB
flash disk or removable hard disk. as picture 3.9.3-4 shows.
Picture 3.9.3-4
Backup
1 choose storage device.
2 Choose video file according to Type, Channel. Time ,etc.
3 Click【Begin】or click 【Cancel】to quit. as picture 3.9.3-5 shows.
27
Picture 3.9.3-5
【Format】:Format external storage device, erase all the information on it, and
please operate carefully.
【Uninstall】:External storage device won’t be identified after uninstall;
【Remove】:Remove external storage device.
【Alarm Type】
1 Motion detection: By analyzing video image, motion detection will
start when system detects movable signals in target area, and linkage function
will be opened.
There will be Picture remind on video channel when movable behavior
occurs.
28
Picture 3.9.4-1
【Set Area】
Choose channel No. according to different alarm type→ click 【Set Area】
→setting area by mouse, white is undetectable area, red is the opposite . as
picture 3.9.4-2 shows.
Picture 3.9.4-2
29
【Sensitivity】: Every area of every channel has separate sensitivity range, the
larger the data is, the higher the sensitivity is and easier to open motion
detection function.
【Schedule Setting】: Device can trigger motion detecting alarm signal only in
the setting period. Period support Monday-Sunday, max 6 periods every day.
Click 【Apply】to save after setup. as picture 3.9.4-3 shows.
Picture 3.9.4-3
【Alarm Linkage】: When motion detection triggered, there will be signal show
on screen.
【Recording Channel】: When motion detection triggered, users can choose
channels for recording: manual setting for special channel/ select 【All】for all
channels recording/ select 【Clean】for no channel recording.
Attention: When finished setting, motion detection should be opened in target
channel if users need recording for motion detection alarm linkage.
Click 【Apply】 when finished, click 【Quit】 to return and check.
2 Video Shelter: When device affected by outside environment, like
light too dark or big change in scenario, video shelter alarm will open, and
alarm linkage will turn on. Alarm mark will show on screen. Setting
30
method is same to motion detection. as picture 3.9.4-4 shows.
Attention: When finished setting, video shelter alarm should be opened in
target channel if users need recording for video shelter alarm linkage.
Picture 3.9.4-4
3 Video Loss: When there is no video in target channels, device can
turn on video loss alarm and linkage opened at the same time. Setting method
is the same to motion detection. as picture 3.9.4-5 shows.
Picture 3.9.4-5
31
Alarm input: can not support at present.
4 Local Alarm
NVR can analyze the status of software and hardware, if there is something
unnormal, device will show alarm mark on screen.
Alarm Type: Disk Full & Disk Error.
Alarm Linkage: When there are alarm issues, if users opened linkage for
screen, once alarm issues triggered, alarm mark will show on screen.
Click 【Apply】 when finished, click 【Quit】 to return and check.
Picture 3.9.4-6
General
【Language】: English
【Device Number】: users can check the device number or re-input it.
【Device name】: Default name nvr, user can alter it.
【Record Type】: Recover or stop recording when disk full.
【 Resolution 】 : Support 1024*768,1280*1024,1440*900,1920*1080, device
32
will restart after modify resolution.
【Transparence】: Users can adjust the degree of transparence for UI.
【Standby time(m)】: Input time, max support 3600min.
【 Tip Guide 】 : Device will enter starting up guide interface if turn on the
function, otherwise, it will be register interface. More details please see the
Picture 3-1.
Click 【Apply】 after setup, click 【Quit】 to return check. as picture 3.9.3-1
shows..
Picture 3.9.5-1
Time Setting
【Zone】: select related zone.
【Date】: set current date and time by hand.
Click 【Apply】after setup.
【 NTP 】 : start NTP service→ Service IP address→ Service port→
internal→ save. System time will sync with INTERNET time server. as
picture 3.9.5-2 shows.
33
Picture 3.9.5-2
User Management
【 Add user 】 : input new user name/password/ choose operating
authorization( all function will be opened if choose 【all】) as picture
3.9.5-3 shows.
Picture 3.9.5-3
【Delete user】:Users can choose the target user name to delete. Admin
is superuser, cannot be deleted.
34
【 Modify user 】 : Users can modify the user name / password/
authorization for selected user. as picture 3.9.5-4 shows.
Click 【Apply】 when finished, click 【Quit】 to return and check.
Picture 3.9.5-4
System maintenance
【 Auto Reboot 】 : Users can set the reboot time. System will reboot
automatically based on setting. as picture 3.9.5-5 shows.
35
Picture 3.9.5-5
【System Upgrade】
1 Insert USB flash disk with upgrade file to NVR, click【NVR Start】to
upgrade WIFI NVR . as picture 3.9.5-6 shows.
Picture 3.9.5-6
2 Insert USB flash disk with upgrade file to NVR, click【WIFI Start】to
upgrade WiFi module. as picture below.
36
Attention: Make sure there is only one upgrade file in USB, too much
Picture 3.9.5-8
System Log
【 Type 】 :User can choose log type to search system log, include:All type,
Alarm, Abnormal, Operation, Information.
【Time】: Users can set the start time and end time for system log searching,
then click 【Query】to show log.
【Clear】: move away the log showed on interface
Picture in 3.9.5-9 is for 【All type】searching, users can scroll mouse to view all
the detail.
37
Picture 3.9.5-9
Click 【 Query 】 to show related log according to searching type, then click
【Clear】 will delete all the log information queried before. as picture 3.9.5-10
shows.
Picture 3.9.5-10
38
Version
Click 【Version】to show Product ID, Product model, System Version, Release
Date, WIFI Version. as picture 3.9.5-11 shows.
Picture 3.9.5-11
Picture 3.10-1
4.11. Shutdown
【Logout:】 logout current user and quit system, need to re-login when open
system next time.
【Reboot】: Quit system and restart.
【Poweroff】: Quit system and shutdown. as picture 3.11-1 shows.
Picture 3.11-1
40
4.12. Mobile Phone View
41
If not familiar about the LAN environment, or private network, users can turn
on “DHCP”, which ensures gaining IP address automatically.
If familiar about LAN, users can set data manually.
4 Open P2P function, as the Picture below:
42
6 Home page icon and function
Add
Play real-time
video of the
Device
current device.
Camera Name:
Cloud service: Green dot means the
If your device has cloud Camera is online, Grey
service, you will see this dot means the Camera is
icon offline.
Setting
7 Share to others
Click “Share type”, users can change the type of sharing, “Share to Video
43
Center”, “Private sharing” or “No share”.
Private sharing: Only share to the particular account.
Share to Video Center: Share to everyone.
8Delete Devices
Users can slide left and select 【Delete】 to
delete the camera.
If you want to give the camera to others, you
must delete the camera from your account;
otherwise others can’t add the camera in
app.
44
4.13. IE View
45