Professional Documents
Culture Documents
3
3
3
Shutdown SIS
Previous Screen
SENR46280028
Pistons
SMCS - 1214-012; 1214-017; 1214-011
Remove Pistons
Start By:
1. Remove the carbon from the top inside surface of the cylinder liners.
3. Remove bearing caps (1) from the two connecting rods. Put pieces of rubber hose or tape on the
threads of the connecting rod bolts as protection for the crankshaft.
NOTE: Put identification on each bearing cap so it will be installed on the correct connecting rod.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/m... 2/1/2020
3412 Generator Set Engine 2WJ00001-UP(SEBP2268 - 42) - Documentation Page 2 of 6
4. Push the pistons up until the piston rings are clear of the cylinder liner. Remove pistons (2).
NOTICE
Do not turn the crankshaft while any of the connecting rods are in the
engine without the caps installed. Do not damage the cooling tubes
when the pistons are removed.
Install Pistons
1. Be sure that the pistons are installed with flat surfaces (2) of the connecting rods toward each other
and the chamfered sides (1) toward the crankshaft.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/m... 2/1/2020
3412 Generator Set Engine 2WJ00001-UP(SEBP2268 - 42) - Documentation Page 3 of 6
2. Put clean engine oil on the piston rings and cylinder liners.
3. Put two pistons in position opposite of each other in the correct bore of the block. Install pistons (3)
with tool (A).
NOTE: For more detail about checking bearing clearances and installation of connecting rod
bearings, see the topic, REMOVE AND INSTALL CONNECTING ROD BEARINGS.
5. Put clean engine oil on bolts (4). Install caps (5) and nuts finger tight. Make sure flat side (6) of
each cap is toward the other cap. The chamfered side must be toward the crankshaft. Tighten each nut
to a torque of 80 ± 8 N·m (60 ± 6 lb ft). Put a mark across the nuts and bolts. Tighten each nut 120°
more.
NOTICE
Do not use an impact wrench to tighten the nuts the additional 120°.
6. Check the side clearance between the two connecting rods on the same crankshaft journal.
Clearance must be 0.28 to 0.84 mm (.011 to .033 in) for new rods.
End By:
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/m... 2/1/2020
3412 Generator Set Engine 2WJ00001-UP(SEBP2268 - 42) - Documentation Page 4 of 6
Start By:
a. remove pistons
Typical Example
1. Remove bearings (3) from the connecting rod and connecting rod cap.
3. Remove pin (2) and connecting rod (4) from the piston.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/m... 2/1/2020
3412 Generator Set Engine 2WJ00001-UP(SEBP2268 - 42) - Documentation Page 5 of 6
4. Remove the pistons rings (5) from the piston with tool (B). Clean the piston ring grooves on the
pistons with an acceptable ring groove cleaning tool.
5. Remove piston skirt (8) from the crown (7). Remove the bearings (9) from the crown.
NOTE: See USE OF PISTON PIN BEARING REMOVAL AND INSTALLATION TOOLS,
SPECIAL INSTRUCTIONS, Form No. SMHS7295.
6. Heat the connecting rod (4) in an oven to a temperature of 177°-260°C (350°-500°F). Never use a
direct flame to heat a connecting rod.
7. Put connecting rod (4) in position on the base plate of tooling (C). Put a new rod pin bearing (6) on
the adapter part of tooling (C).
NOTE: The old bearing is pushed out by tooling (C) as the new bearing is installed.
8. Use tooling (C) to push the new bearing into the connecting rod until the push adapter of tooling
(C) makes full contact with the connecting rod surface.
9. Use a pin boring machine to make the rod pin bearing the correct size. The bore in the new rod pin
bearing must be 50.830 ± 0.008 mm (2.0012 ± .0003 in).
10. Check the clearance between the ends of the piston rings. See PISTONS AND RINGS in
SPECIFICATIONS.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/m... 2/1/2020
3412 Generator Set Engine 2WJ00001-UP(SEBP2268 - 42) - Documentation Page 6 of 6
11. Install bearings (9) in piston crown (7) and install skirt (8). The depth of bearings are 1.0 ± 0.1
mm (.039 ± .004 in) from the inside edge of the crown boss. Make sure the holes in the bearings are
lined up with the holes in the crown.
12. Install the oil ring spring in the oil ring groove of the piston.
NOTE: The oil ring is to be installed over the spring with the oil ring end gap 180° from the oil ring
spring point.
13. Install the oil ring on the piston with tool (B).
14. Install the second (intermediate) piston ring with the side that has the identification "UP-2" toward
the top of the piston with tool (B).
15. Install the top ring with the side marked "UP-1" toward the top of the piston with tool (B).
NOTE: After the installation of all three piston rings put the piston rings in position so the end gaps
are 120° apart.
16. Put the piston in position on connecting rod (4). Put clean engine oil on pin (2) and install the pin.
Install retainer rings (1) with tool (A). Make sure the retainer rings are in the grooves of the piston.
17. Install bearings (3) in the connecting rod and connecting rod cap.
End By:
a. install pistons
Copyright 1993 - 2020 Caterpillar Inc. Thu Jan 2 21:18:48 EST 2020
All Rights Reserved.
Private Network For SIS Licensees.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/m... 2/1/2020