Professional Documents
Culture Documents
SC-F6200 SETUP MANUAL E (MP) RevD
SC-F6200 SETUP MANUAL E (MP) RevD
C March 10, 2017 Revision to change the order of assembling and add the tool
Refill ink.
-Use up all ink in the pack at a time.
SE Group Confidential (Related Staff Only) Until: Permanent (No remaining)
4
< Caution >
After 100units,
This screws will be changed
• Silver ones : 2pcs (Running change)
• Blue ones : 2pcs
<Unnecessary for Serial Nr. X42*******> <Unnecessary for Serial Nr. X42*******>
Ex2
<Unnecessary for Serial Nr. X42*******>
When lifting the printer unit, only hold the highlighted area. Otherwise, it may
affect normal operation and printing.
C x 10
Main unit bottom front side
SE Group Confidential (Related Staff Only) Until: Permanent
13
Model: WC********
2. Loosen 4 screws and make sure the plates to be able to move up/low and left/right.
Full side Home side
Not to
touch
2. Make sure the color index on the plate and Put each CSIC on each slider.
IMPORTANCE
Slider
CSIC
3. Set only Cyan and Black Ink Tanks into Ink Holder as the same order as the
color index.
Set the tank with Chip/Slider
Black during pushing slider.
Cyan
SE Group Confidential (Related Staff Only) Until: Permanent
15
Model: WC********
IMPORTANCE
Cyan Black
D x 2 (Blue screws)
Temporarily Tighten
Temporarily Tighten
SE Group Confidential (Related Staff Only) Until: Permanent
16
Model: WC********
Tighten
Cyan Black
Tighten Tighten
To fix the tank To fix the tank
SE Group Confidential (Related Staff Only) Until: Permanent
17
Model: WC********
Tighten
Thickness
SE Group Confidential (Related Staff Only) Until: Permanent
gauge(2.5mm) 19
Model: WC********
2. Tighten 4 screws to fix the tanks. (Yellow => Magenta => Black => Cyan )
Dx2
SE Group Confidential (Related Staff Only) Until: Permanent
20
Model: WC********
OK!!
Tighten Tighten
Loosen Loosen
Tighten Tighten
2 screws
Tighten
3. Tighten 4 screws.
Tighten
V1
PLATE,TRAY,CISS
Hook
TRAY,CISS
FIXING PLATE,TRAY
Insert
V1
SE Group Confidential (Related Staff Only) Until: Permanent
26
Model: X42*******
TRAY,CISS TRAY,RIGHT
V1 TRAY,LEFT
V1
Positioning Insert
Positioning
TRAY,CISS
Back
V2
Tray unit
Hook
Printer
FRAME,SIDE,CISS FRAME,SIDE,CISS
Align tip of triangle with edge Align tip of triangle with edge
of metal plate with screws of metal plate with screws
V3 V3
SE Group Confidential (Related Staff Only) Until: Permanent
31
Model: X42*******
Hook Hook
FRAME,CISS,BOTTOM V1
V4
2
4
3
1
Should be aligned
V1
2. Tighten 2 screws.
Gx2
SE Group Confidential (Related Staff Only) Until: Permanent
40
Setting the Waste Ink Tank.
1. Put clamp.
Near hole
1-3mm Gap
Top of hole
Adjustable
INSULOK
Waste
Ink
Joint
Stopper
<Caution>
1. Get all the ink out of the ink pack so that there is none remaining.
Do not use the ink in an ink pack to refill multiple different ink
tanks. This can cause messages from the remaining ink warning
system to not be displayed properly.
2. Do not turn on printer before filling all inks.
3. Confirm whether Ink Tank color is suitable for Ink Pack color when
fill the ink.
After filling all ink as pictures, please turn on printer by FW update mode.
3. Start Ink Charge after making sure waste ink bottle was set.
Check again of C
Ink Tank position