= _ UDC 621.886.123
DEUTSCHE NORMEN November 1978
Grooved Pins, Full Length Parallel-grooved
with Chamfer
Zylinderkerbstifte
1. Definition and purpose
Grooved pins according to this Standard are positive or non-positive connecting elements. They are used as connecting
pins, the pin being seated firmly in the acommodating hole, for which tolerance zone H11 is recommended.
2 Other relevant Standards
DIN 267 Part 1 Bolts, screws, nuts and similar threaded and formed parts; technical conditions of delivery, general
information
DIN 267 Part Bolts, screws, nuts and similar threaded and formed parts; technical conditions of delivery, testing
and acceptance
DIN 1651 Free cutting steels; technical conditions of delivery
3 Dimensions, designation _»..
Designation of a grooved pin, full length parallel-grooved with chamfer, of nominal diameter dy = Smm and length
T= 30mm, made of 9 SMAPb 28 K (St)
Grooved pin 1473 — 5 x 30 — St
Co
ees is 2 [as] 3
25 [28] 3537 as}s2 [6
Table 1.
7 kontnense] OF TT De se Tee
pes dev rm
‘Oia [orey 02 Tore] 03 | oa [oi
os7{ 0s fos} os iz] is} is] 2
0.70] 1.00] 160| 285 425/6,15/ 106] 165] 228 | 405) 69.2| 91.0 236.5)
Sei Sean oe LT
pwr dev fords +308 ros
‘The normal commercial lengths lie between the stepped lines. Intermediate lengths are permissible but should be
avoided if possible.
Continued on pages 2 t0 4
1) and 2) see page 2
Explanations on page 4
woh of GorvanSarauae (OW Nomen) are wihBeutnverag Gnor Borin SoanaKAnT DIN 1473. engl. Preisgr. 4
eee call a Verte Nr, 0108Page 2 DIN 1473
4 Weights
‘The weights given in Table 2 apply to grooved pins made from steel
Table 2.
JNominal diameter ay} 08 | 1 | 12} 1s] 2]25/3 | 4] s]6] se [wo] 12] | a6 | 20 | 25
‘Wight (7.85 kale) kg/1000 pices ~
‘
5 o.020 0,031 |0,048|0,070 0,124
6 o.024 [0.037 |0,0530,083)o,148 0,231 jo,233 0,502
3s o.032/0,048 0,0710,111 fo,108)0,308 0 446,760] 1.23
70 (0.062 [0,088 0,138 0,247|0,305|0,s55}0,986| 1.54 | 222
2 |___Jo.107]0.167),206|o,462)o,666 1.18 | 1.86 | 266 | 4.74
16 (0.222|0.305 0.616 |0.888|1.56 [2,46 |355 [67
0 (0278)0.96)o,770)1,11 1.97 | 308 | 4.4 7,90 | 12 | 17.8 | 24.2
ES 618 0,965 |1,39 |2.46 | 3,86 | 5.55 | 9.80
30 jo.72)i.16 [168 [296 [4.52 [eas | 118 aa vat | 16
38 h1.96 j<5, 727} 13,7 | 218 [31.1 [423 [58.3 | 06,4 | 195
0
6
‘50
f0.016 0,025 J0,036 Jo.056 [ees
| bz ee 3s | 15.7 63.2 | 90.8 | 156
jeaa [693 [9.99 17,7 malay [178
93 | 7,701.1 | 19,6 790 | 124 | 192
5 _ a2 | 94 |1a2 69 |136 | 212
oo 7 22 [ear /aa]ns| ea [148 | 201 |
— — | 144256 | 01 [578 |r06 [109 | 161 | 250
70 i 155 | 275 | «22 | 600 [are [111 |173 | 270
75 168] 205 [463 | 623 }e47] 19 | 106 | 260
20 178|315| 494 |71.1 [968 |126 | 198 | 208
~ 7 L ie 35,4 [55,5 | 20.0 |109 | 142 | 222 | 246
700 | a 3946.7] aa9 [iat [18 [207 | 365
10 | 67997819 |174 | 272 | 424
wo] | | 240 | 107 [148 |100 |206 | 463
5 Material
‘St = 9SMnPb 28 K according to DIN 1651
Other materials, for example 45S 20 K (according to DIN 1651), X 12 CrMoS 17 {according to DIN 17.440),
X 12CrNiS 188 (according to DIN 17 440), ALCuMgPb F37 (according to DIN 1747 Part 1), CuZn38Pb 1.5 F41
(according to DIN 17671 Part 1), as well as plastics or special heat treatments by agreement,
6 Finish
Surface: Normal finish bright, oiled
Other finishes by agreement, e.g. galvanic coatings according to DIN 267 Part 9 or phosphate coatings according to
DIN 50942,
7 Requirements
DIN 267 Part 1 applies for general requirements
1) The groove angle 70° + 3° and the diameter over the groove edges dy apply only to grooved pins made of
9.SMnPb 28K (St).
2) A check should be made in each particular case to determine whether these shear forces can be fully taken into
account according to the design parameters.8 Testing
8.1. Testing of dimensional accu
“The provisions of DIN 267 Part 5 apply, as appropriate, for the testing of dimensional accuracy and finish.
, Table 4 of this Standard applies.
racy and finish
For the main and subsidiary features, Table 3 applies; for the acceptable quality Ii
Table 3, Main and subsidiary features
Main feature
Subsidiary feature
Nomi
inal diameter dy
Diameter over groove edges d2
Nominal
length f
Table 4. AQL values
Nature
of feature for testing for testing
of features for faulty parts
Main feature 18 18
Subsidiary feature 25 25
8.2. Testing the mechanical characteristics and materials,
‘The provisions of DIN 267 Part § apply, as appropriate, for testing the mechanical characteristics and materials.
{A Standard is being prepared for the shear test
9 Examples of application
Figure 1. Use as locking pin in a nipple Figure 2. Use as radial pi
toa shaft
Figure 3. Use as round wedge for fastening a screw con. Figure 4, Use as tangent pin
veyor to a shaft end
for connecting a bevel wheel
DIN 1473 Page 3age 4 DIN 1473,
Further Standards
DIN 1469
DIN 1470
DIN 1471
DIN 1472
DIN 1474
DIN 1475,
DIN 1476
DIN 1477,
Grooved pins, half length grooved with gorge
Grooved pins, full length parallel-grooved with pilot
Grooved pins, full length taper-grooved
Grooved pins, half length taper-grooved
Grooved pins, half length reverse-grooved
Grooved pins, third length centre-grooved
Round head grooved pins
Countersunk head grooved pins
Explanations
Compared with the September 1956 edition of DIN 1473, this subsequent edition con-
{tains the following amendments and additions:
a) The nominal diameter 13 mm has been deleted.
D) The series of lengths has been changed to some extent and brought into line with the
internationally standard series of lengths for connecting elements
) The position and shape of the grooves has been specified
44) Double shear forces have been adopted. A Standard for an appropriate shear testis
being prepared,
¢} Information on the material has been given, Instead of the previous strength cate
gory 6S, the material 9 SMinPb 28 K has been stipulated because the new strength
Categories according to DIN 267 Part 3 arenot applicable to grooved pins. A reference
fhas also been made to other materials, the use of which is subject to special agreement.
4) Technical conditions of delivery have been included and brought into line with
DIN 267 Part 1 and Part 5.
9) The standard designation has been amended,
hy The content of the Standard has been revised editorially,