Professional Documents
Culture Documents
Solid State Sciences Volume 55 Issue 2016 (Doi 10.1016/j.solidstatesciences.2016.02.014) Paz, E.C. Lodi, T.A. Gomes, B.R.A. Melo, G.H.A. Pedrochi, F. - Optical and Spectroscopic Investigation o PDF
Solid State Sciences Volume 55 Issue 2016 (Doi 10.1016/j.solidstatesciences.2016.02.014) Paz, E.C. Lodi, T.A. Gomes, B.R.A. Melo, G.H.A. Pedrochi, F. - Optical and Spectroscopic Investigation o PDF
E.C. Paz, T.A. Lodi, B.R.A. Gomes, G.H.A. Melo, F. Pedrochi, A. Steimacher
PII: S1293-2558(16)30037-1
DOI: 10.1016/j.solidstatesciences.2016.02.014
Reference: SSSCIE 5292
Please cite this article as: E.C. Paz, T.A. Lodi, B.R.A Gomes, G.H.A. Melo, F. Pedrochi, A. Steimacher,
Optical and spectroscopic investigation on Calcium Borotellurite glass system, Solid State Sciences
(2016), doi: 10.1016/j.solidstatesciences.2016.02.014.
This is a PDF file of an unedited manuscript that has been accepted for publication. As a service to
our customers we are providing this early version of the manuscript. The manuscript will undergo
copyediting, typesetting, and review of the resulting proof before it is published in its final form. Please
note that during the production process errors may be discovered which could affect the content, and all
legal disclaimers that apply to the journal pertain.
ACCEPTED MANUSCRIPT
TeO2
0 Glass 2.5
100 CBT20
PT
CBT25
20 CBT30
80 2.0
CBT35
RI
CBT40
CBT50
2
F
Ca 40
60
Te
1.5
SC
O+
O2
Ca
60
40
1.0
U
80
AN
20
0.5
100
0
M
CaO+CaF2 0 20 40 60 80 100 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0
B2O3
B2O3 hv (eV)
D
TE
C EP
AC
Optical and spectroscopic investigation on
ACCEPTED MANUSCRIPT
Calcium Borotellurite glass system
HIGHLIGHTS
PT
• Optical and spectroscopy properties of glasses on Calcium Borotellurite system were studied
• The results suggest that TeO2 addition increases NBO in the structure of CaBTe glass.
•
RI
TeO2 addition shifts the absorption edge to longer wavelengths and reduce optical band gap
• The density and the refractive index increases with TeO2 content
SC
• The optical basicity and the electronic polarizability increase with TeO2 content
ABSTRACT
U
AN
In this work, the glass formation in Calcium Borotellurite (CBTx) system and their optical properties
were studied. Six glass samples were prepared by melt-quenching technique and the samples obtained
M
are transparent, lightly yellowish, without any visible crystallites. The results showed that TeO2 addition
D
increases the density, the electronic polarizability and, consequently, the refractive index. The increase
TE
of electronic polarizability and optical basicity suggest that TeO2 addition increases the non-bridging
oxygen (NBO) concentration. The increase of TeO2 shifts the band edge to longer wavelength owing to
EP
increase in non-bridging oxygen ions, resulting in a linear decrease of optical energy gap. The addition
of TeO2 increases the temperature coefficient of the optical path length (dS/dT) in room temperature,
C
which are comparable to phosphate and lower than Low Silica Calcium Alumino Silicate (LSCAS)
AC
glasses. The values of dS/dT present an increase as a function of temperature for all the samples
measured. The results suggest that CBTx is a good candidate for rare-earth doping and several optical
applications.
Keywords:
Optical and spectroscopic properties of tellurite, borate and borotellurite glasses have been
widely investigated for their scientific interest and practical applications [1–5]. Borate glasses are
known for having high thermal stability, high chemical durability, good solubility of rare-earth ion and
also for their ease of synthesis [4,6,7]. Tellurite glasses have lower phonon energy if compared to
phosphates and silicates glasses, large infrared transparency, good thermal and mechanical stability,
PT
good chemical durability, low melting temperature, high refractive index, high dielectric constant and
RI
suitability as host matrix to dopant action [2–5,7–12]. These features make tellurite glasses promising
candidates for photonic applications, such as fiber in optical communication, window materials and up-
SC
conversion laser. The addition of tellurium oxide to another glass former, such as B2O3, can lead to the
U
production of interesting structural units that affect the physical properties of the glass network [13,14].
AN
The presence of TeO2 in alkali borate glasses decreases their hygroscopic nature, reduces their phonon
energy, increases their refraction index and their IR transmission [14–16]; that makes borotellurite
M
glasses candidates for several optical and photonic applications. In order to improve those qualities,
calcium oxide and calcium fluoride were used as glass modifiers due to their excellent contributions to
D
the glassy formation. Calcium oxide can form promising luminescent host matrix, in which Ca2+ cation
TE
can be replaced by rare earth ions [17]. Furthermore, CaO addition increases the glass resistance to
humidity [18] as well as the thermal stability of the glass, as could be observed when other alkaline
EP
earth was added to tellurite glasses [19]. Besides that, the addition of fluorine compounds, such as CaF2,
C
decreases the phonon energy of pure oxide glasses and can improve emission and lifetime of rare earth
AC
system, with different concentrations of TeO2. Besides that, we present an investigation of the optical
and spectroscopy properties in order to study the effect of glass former TeO2 on CBTx glasses. We
expect that the glass studied in the CBTx system can be used for optical fiber draw, optical amplifiers or
0.6x)B2O3-xTeO2 (x=20, 25, 30, 35, 40 and 50 wt%), referred as CBTx, was carried out by melt
quenching conventional technique. The starting materials, chemical reagents of analytical grade (purity
PT
98-100 %), were melted at ~950° C in platinum crucibles, under air atmosphere. The melt was poured
RI
into a preheated stainless steel mold at ~500°C and annealed for 4 h to release its inner stress.
SC
2.2. Characterization
The refractive index was measured at room temperature using the Brewster’s angle method,
U
AN
using 2mW He–Ne(632.8nm) laser.[22]
The optical absorption spectra for all the glass samples was recorded using Schimadzu
M
To determine the thermal coefficient of the optical path length change (dS/dT = 1/L(ds/dT)), an
D
optical interferometric technique was used. The experimental setup and the theory for this method is
TE
described in details in Ref.[23]. The dS/dT value measured with this technique is given by (dS/dT) =
n + (dn/dT), where n is the refractive index, is the linear thermal expansion coefficient, and
EP
varying from 20 to 50 wt%, present good optical quality under visual inspection, without any visible
crystallites or devitrification. The pale yellow color of the samples increases lightly with TeO2 content.
The concentration of TeO2 up to 50 wt% was verified without any effect in the glass formation
field. All the samples prepared in that system has no crystalline phase, as confirmed by XRD (not
PT
shown). The phase diagram (wt%) of the obtained glass samples are presented in Fig. 2.
Fig. 3 presents the refractive index n and the volumetric density as a function of TeO2 content,
RI
which increases linearly with TeO2 increase.
SC
The density of the CBTx glass samples increases from 2.97 g cm-3 to 3.58 g cm-3, which
corresponds to an increase of ~21%. That increase occurs mainly due to the substitution of boron and
U
calcium oxide by tellurium oxide, which has a higher molecular weight than B2O3 and CaO, resulting in
AN
a higher net weight of the glass structure [15,24]. The values of refractive index increase from 1.62 to
1.71, for CBT20 and CBT50, respectively. High values of refractive index are desirable for fiber optic
M
design and waveguide applications. The increase of refractive index with TeO2 content is mainly related
D
to the increase of volumetric density [25] and the electronic polarizability [26]. The electronic
TE
polarizability of the oxide ion (αO2-) is one of the most important properties which govern the non-
The average electronic polarizability (αm), which relates molar refraction (Rm) to refractive
index and molar volume of a glass, was calculated using the The Lorentz–Lorenz equation [28]:
C
3R (1)
α =
AC
4πN
Theoretical optical basicity (OB) for the glass system under study was calculated by using
basicities assigned to the individual oxides on the basis of the following equation proposed by Duffy and
Ingram [29,30]
Λ = X Λ + X Λ + X Λ … X Λ (2)
where, , , … ) are the equivalent fractions of different oxides, i.e. the proportion of the oxide
ACCEPTED MANUSCRIPT
atom that contribute to the glass system and , , … are optical basicity values assigned to the
The average electronic polarizability and optical basicity for the glass system under study are
presented in Fig. 4.
The concept of optical basicity was defined by Duffy et al. and it is related to the ability of
PT
oxygen to donate negative charges [29]. The total basicity of a glass containing both bridging and non-
bridging oxigens (NBO) depends on the relative proportion of these two types of linkages. The increase
RI
of this value (as observed in Fig. 4) with the addition of TeO2 means that the structure is more
SC
depolymerized, i.e. the number of NBO ions in the network increased. Optical basicity also depends on
the glass constitution (formers and modifiers) and the electronegativity of the cations in the glass
U
network. The evaluation of this OB values also can be useful to study changes in coordination number,
AN
as observed in tellurite glasses by Moraes[32]. OB is inversely proportional to the electronegativity
between bonded atoms in the oxide[30]. It is known that valence and conduction bands essentially
M
originate from O2− orbitals and cations. Thus, the promotion of an electron from valence band to
D
conduction band by the interaction with an absorbed photon is analogous to electron transfer between
TE
ions. Consequently, the difference in the electronegativity of the O2− ions and cations of the glass is
related to the band gap of the matrix. As follows, if the OB increases, a decrease in the band gap Eopt
EP
values is expected. Because of these reasons, the optical basicity is an important parameter to study
physical aspects, such as refractivity, network coordination number changes, chemical durability, UV
C
transparency, etc. According to Duffy[33], the increase of optical basicity causes an increase in the
AC
oxygen polarizability, which is interpreted in terms of the less controlled electron charge clouds being
unable to oscillate at higher ultraviolet frequencies, degrading ultraviolet transmission. The increase in
the polarizability of oxygen ions, as observed in Fig. 4, is also an indication that the concentration of
NBOs increases.
Fig. 5 shows the optical absorption spectra of the samples as functions of TeO2 content. Fig.
5(a) presents the absorption spectra for the CBT20 sample. The transmittance window from 350 to 2200
nm makes the CBTx glasses suitable for several rare earth doping. Erbium doped glasses, for instance,
have attracted attention due to the infrared emission at 1530 nm through the 4I13/2→ 4I15/2 transition,
ACCEPTED MANUSCRIPT
which exhibits extensive applications in telecommunications as doped fiber amplifier [34]. The
absorption band around 2400 nm is assigned to OH groups in the glass structure in several oxide glasses
[35][36]. The fundamental absorption edge of the absorption spectra changes with the increase in TeO2
content due to the structural rearrangement in the glass structure. The absence of sharp absorption edge
is characteristic of the glassy state of the samples. We note that the UV optical absorption shifts toward
PT
higher wavelengths with TeO2 content, as predicted by optical basicity and electronic polarizability
results. Variations of glass basicity are also related to the electronegativity of oxygen and the optical
RI
band gap (Eopt). The increase of glass basicity results in a decrease of Eopt, reducing the UV
SC
transmission. According to Stevels [37], the shift of band edge to higher wavelengths occur due to an
increase of non-bridging oxygens (NBO), which increase with TeO2 content. The increase of NBO
U
induces a higher depolymerization of CBTx glasses network, leading to a decrease in optical energy
AN
gap.
The band gap energy values for all the samples were estimated by the following equation, which
M
ℎ ! ∝ ℎ − $%& !'
D
(3)
TE
in which is the optical absorption coefficient, presented in Fig. 5, ℎ is the photon energy, and Eopt is
the band gap energy. The parameter m depends on the band gap characteristic as m= ½ for direct
EP
allowed transition, m= 3/2 for direct forbidden transition, m=2 for indirect allowed transition, and m=3
for indirect forbidden transition. For CBTx glasses the best plots were obtained for m=2. Tauc’s plot of
C
(
ℎ ! as a function of photon energy (ℎ ) for the indirect allowed transitions of the CBTx samples
AC
are shown in Fig. 6 (left). This indicates that indirect allowed transition is responsible for shifting the
absorption edge to longer wavelength, as observed in the spectra of Fig. 5. The energy band gap values
of the samples were obtained by extrapolating the fittings of Fig. 6 (left), with ℎ !/ = 0. The band
gap values, obtained by extrapolation, as functions of TeO2 content are shown in Fig. 6 (right).
From Fig. 6 (right) one can see that when TeO2 content increases, the band gap energy values
decrease linearly, varying from 3.62 to 3.18 eV, for CBT20 and CBT50, respectively. These values are
excited than the bridging oxygen (BO), which changes the absorption characteristics [33,37,38].
The temperature coefficient of the optical path length (dS/dT) is one of the most important
thermo-optical parameters in the design of optical systems, such as lasers, optical fiber for
telecommunications and also in the development of optical glasses. dS/dT carries information about the
PT
thermal expansion coefficient (cte), electronic polarization and refractive index changes, which are
dependent on temperature. Particularly, in solid state laser using rods as active medium, this parameter
RI
is of importance, since it describes the distortion of the laser beam induced by a temperature change in
SC
the medium.
The temperature coefficient of optical path length is obtained from Eq. (4)
U
,- ,0 1 ,4 (4)
+ / = + / + 0 = + /
,. ,. 23 ,.
AN
in which c6 = 1(L 9dL(dT< is the linear thermal expansion coefficient, m are multiples of wavelength,
M
which correspond to the difference between the two optical path lengths (∆>! of the beams reflected in
the sample surfaces and the dS(dT = 1(L 9ds(dT<, which s is the optical path > = 03 = 1(2 4 [23].
D
TE
The dm/dT was calculated by numerical differentiation of the data followed by smoothing. The results
The dS/dT at room temperature for the studied samples is shown in Table 1. It is possible to
verify that the TeO2 addition increases the dS/dT. The addition of TeO2 in borotellurite glasses increases
C
the refractive index, the electronic polarizability and the thermal expansion coefficient[25], which are
AC
directly related with the dS/dT. The dS/dT values of the glasses studied are comparable with phosphate
(~12. 10-6 K-1) and lower than Low Silica Calcium Alumino Silicate glasses (~19. 10-6 K-1) [23]. In Fig.
7 dS/dT increases with the temperature for all the samples studied. This information is very important in
optical systems design such as solid state laser, where the local active medium temperature can reach a
temperature of the order of 150ºC [41,42], increasing therefore the magnitude of dS/dT, and
The glass forming ability and optical properties of the CBTx system were investigated for the
first time in this work and the phase diagram was presented. The glass samples obtained are transparent,
lightly yellowish, with no visible crystallites. The density of CBTx glasses increases due the substitution
of B2O3 and CaO (lower molecular weight) by TeO2 (higher molecular weight). Refractive index
PT
increases mainly due to the increase of density and electronic polarizability. The increase of electronic
polarizability and optical basicity suggest that TeO2 addition increases the NBO concentration. The
RI
optical basicity values are found to be in range 0.648–0.709 for the CBTx glass system. The increase of
SC
TeO2 shifts the band edge to longer wavelength owing to increase in non-bridging oxygen ions, resulting
in decrease of optical energy gap. The values of optical energy gap decrease linearly from 3.62 to 3.18
U
eV, with TeO2 addition up to 50 wt%. The results of dS/dT present an increase as a function of
AN
temperature for all measured samples. The addition of TeO2 also increases dS/dT values in room
temperature. The values obtained are comparable with phosphate and lower than LSCAS glasses. The
M
results suggest that CBTx are good candidates for rare-earth doping for several optical applications,
D
such as fiber in optical communication, optical amplifiers, window materials and up-conversion laser.
TE
We expect that the results in this work will be useful for understanding the influence of TeO2 on the
Acknowledgments:
AC
We are thankful to the Brazilian agencies CNPq, CAPES, FINEP, and FAPEMA for financial support of
this study.
5. References
ACCEPTED MANUSCRIPT
[1] I. Ardelean, F. Ciorcas, M. Peteanu, I. Bratu, V. Ioncu, M. Tehnology, The structural atudy of
Fe2O3-TeO2-B2O3-SrF2 glasses by IR spectroscopies, 14 (2000) 653–661.
[2] M. a. Khaled, H. Elzahed, S. a. Fayek, M.M. El-Ocker, Optical absorption, infrared and
differential thermal analysis studies of borotellurite glass containing nickel, Mater. Chem. Phys.
37 (1994) 329–332. doi:10.1016/0254-0584(94)90170-8.
[3] I. Jlassi, H. Elhouichet, M. Ferid, Thermal and optical properties of tellurite glasses doped
erbium, J. Mater. Sci. 46 (2011) 806–812. doi:10.1007/s10853-010-4820-x.
PT
[4] E.S. Nurbaisyatul, K. Azman, H. Azhan, W.A.W. Razali, A. Noranizah, S. Hashim, et al., The
optical properties of trivalent rare earth ions (Er3+) doped borotellurite glass, Opt. Spectrosc. 116
(2014) 413–417. doi:10.1134/S0030400X14030163.
RI
[5] K. Selvaraju, K. Marimuthu, Structural and spectroscopic studies on concentration dependent
Er3+ doped boro-tellurite glasses, J. Lumin. 132 (2012) 1171–1178.
SC
doi:10.1016/j.jlumin.2011.12.056.
[6] S. Shailajha, K. Geetha, P. Vasantharani, S.P. Sheik Abdul Kadhar, Effects of copper on the
preparation and characterization of Na–Ca–P borate glasses, Spectrochim. Acta Part A Mol.
U
Biomol. Spectrosc. 138 (2015) 846–856. doi:10.1016/j.saa.2014.10.101.
AN
[7] K. Annapoorani, K. Maheshvaran, S. Arunkumar, N. Suriya Murthy, K. Marimuthu, Structural
and luminescence behavior of Er(3+) ions doped Barium tellurofluoroborate glasses.,
Spectrochim. Acta. A. Mol. Biomol. Spectrosc. 135 (2015) 1090–8.
M
doi:10.1016/j.saa.2014.08.003.
[8] S. Sakida, S. Sakida, S. Hayakawa, S. Hayakawa, T. Yoko, T. Yoko, Part 2. 125Te NMR study of
M2O-TeO2 (M = Li, Na, K, Rb and Cs) glasses, J. Non. Cryst. Solids. 243 (1999) 13–25.
D
[9] E.S. Yousef, Er3+ ions doped tellurite glasses with high thermal stability, elasticity, absorption
TE
intensity, emission cross section and their optical application, J. Alloys Compd. 561 (2013) 234–
240. doi:10.1016/j.jallcom.2013.01.199.
[10] H. Burger, W. Vogel, IR Transmission and properties of glasses in the TeO2-[RnOm, RnXm,
EP
[12] K. Shioya, T. Komatsu, H.G. Kim, R. Sato, K. Matusita, Optical properties of transparent glass-
ceramics in K2O-Nb2O5-TeO2 glasses, J. Non. Cryst. Solids. 189 (1995) 16–24.
[13] M.A. Khaled, H. Elzahed, S.A. Fayek, M.M. El-Ocker, Optical absorption, infrared and
differential thermal analysis studies of borotellurite glass containing nickel, Mater. Chem. Phys.
37 (1994) 329–332. doi:10.1016/0254-0584(94)90170-8.
[14] S.P.H.S. Hashim, H.A.A. Sidek, M.K. Halimah, K.A. Matori, W.M.D.W. Yusof, M.H.M. Zaid,
The effect of remelting on the physical properties of borotellurite glass doped with manganese.,
Int. J. Mol. Sci. 14 (2013) 1022–30. doi:10.3390/ijms14011022.
[15] Y.B. Saddeek, L.A. El Latif, Effect of TeO2 on the elastic moduli of sodium borate glasses, Phys.
B Condens. Matter. 348 (2004) 475–484. doi:10.1016/j.physb.2004.02.001.
[16] T.V.R. Rao, R.R. Reddy, Y. Nazeer Ahammed, M. Parandamaiah, N. Sooraj Hussain, S.
Buddhudu, et al., Luminescence properties of Nd3+: TeO2-B2O3-P2O5-Li2O glass, Infrared
ACCEPTED MANUSCRIPT
Phys. Technol. 41 (2000) 247–258.
[18] C.N. Santos, D. De Sousa Meneses, P. Echegut, D.R. Neuville, A.C. Hernandes, A. Ibanez,
Structural, dielectric, and optical properties of yttrium calcium borate glasses, Appl. Phys. Lett.
94 (2009) 151901. doi:10.1063/1.3115796.
[19] G. Senthil Murugan, T. Suzuki, Y. Ohishi, Raman characteristics and nonlinear optical properties
PT
of tellurite and phosphotellurite glasses containing heavy metal oxides with ultrabroad Raman
bands, J. Appl. Phys. 100 (2006). doi:10.1063/1.2215218.
[20] Y. Zhang, Z. Zhu, W. Zhang, Y. Qiao, Photoluminescence properties of Sm3+ ions doped
RI
oxyfluoride calcium borosilicate glasses, J. Alloys Compd. 566 (2013) 164–167.
doi:10.1016/j.jallcom.2013.03.092.
SC
[21] V. Nazabal, S. Todoroki, a. Nukui, T. Matsumoto, S. Suehara, T. Hondo, et al., Oxyfluoride
tellurite glasses doped by erbium: Thermal analysis, structural organization and spectral
properties, J. Non. Cryst. Solids. 325 (2003) 85–102. doi:10.1016/S0022-3093(03)00313-2.
U
[22] S. Schutzmann, M. Casalboni, F. De Matteis, P. Prosposito, Refractive index measurements of
AN
thin films using both Brewster and m-line technique: A combined experimental setup, J. Non.
Cryst. Solids. 351 (2005) 1814–1818. doi:10.1016/j.jnoncrysol.2005.04.022.
[23] A. Steimacher, A.N. Medina, A.C. Bento, J.H. Rohling, M.L. Baesso, V.C.S. Reynoso, et al., The
M
temperature coefficient of the optical path length as a function of the temperature in different
optical glasses, J. Non. Cryst. Solids. 348 (2004) 240–244.
D
[24] B.V.R. Chowdari, P.P. Kumari, Studies on Ag2O.MxOyTeO2 (MxOy = WO3, MoO3, P2O5 and
B2O3) ionic conducting glasses, Solid State Ionics. 113 (1998) 665–675.
TE
[26] P. Joshi, S. Shen, A. Jha, Er3+-doped boro-tellurite glass for optical amplification in the 1530–
1580 nm, J. Appl. Phys. 103 (2008) 083543.1–083543.7. doi:10.1063/1.2908873.
[27] G. Upender, C.S. Devi, V.C. Mouli, Role of WO3 on DC conductivity and some optical
C
doi:10.1016/j.materresbull.2012.06.024.
[28] V. Dimitrov, T. Komatsu, Classification of oxide glasses: A polarizability approach, J. Solid State
Chem. 178 (2005) 831–846. doi:10.1016/j.jssc.2004.12.013.
[29] J.A. Duffy, M.D. Ingram, An interpretation of glass chemistry in terms of the optical basicity
concept, J. Non. Cryst. Solids. 21 (1976) 373–410. doi:10.1016/0022-3093(76)90027-2.
[30] J.A. Duffy, A review of optical basicity and its applications to oxidic systems, Geochim.
Cosmochim. Acta. 57 (1993) 3961–3970. doi:10.1016/0016-7037(93)90346-X.
[31] V. Dimitrov, T. Komatsu, Electronic polarizability, optical basicity and non-linear optical
properties of oxide glasses, J. Non. Cryst. Solids. 249 (1999) 160–179.
[32] J.C.S. Moraes, J.A. Nardi, S.M. Sidel, B.G. Mantovani, K. Yukimitu, V.C.S. Reynoso, et al.,
Relation among optical, thermal and thermo-optical properties and niobium concentration in
ACCEPTED
tellurite glasses, J. Non. Cryst. Solids. 356MANUSCRIPT
(2010) 2146–2150.
doi:10.1016/j.jnoncrysol.2010.07.044.
[33] J.A. Duffy, Ultraviolet transparency of glass: A chemical approach in terms of band theory,
polarisability and electronegativity, Phys. Chem. Glas. 42 (2001) 151–157.
[35] A. Steimacher, N.G.C. Astrath, A. Novatski, F. Pedrochi, A.C. Bento, M.L. Baesso, et al.,
PT
Characterization of thermo-optical and mechanical properties of calcium aluminosilicate glasses,
J. Non. Cryst. Solids. 352 (2006) 3613–3617.
[36] G. Navarra, I. Iliopoulos, V. Militello, S.G. Rotolo, M. Leone, OH-related infrared absorption
RI
bands in oxide glasses, J. Non. Cryst. Solids. 351 (2005) 1796–1800.
doi:10.1016/j.jnoncrysol.2005.04.018.
SC
[37] J.M.Stevels, Ultraviolet transmittivity of glasses, in: Proc. 11th Int. Congr. Pure Appl. Chem.,
1953: p. 519.
U
[38] K. Maheshvaran, K. Marimuthu, Concentration dependent Eu3+ doped boro-tellurite glasses—
Structural and optical investigations, J. Lumin. 132 (2012) 2259–2267.
AN
doi:10.1016/j.jlumin.2012.04.022.
[39] N.F.Mott. and E.A. Davis, Eletronic Process in Non-Crystalline Materials, Oxford, Claredon,
1979.
M
[40] P. Gayathri Pavani, K. Sadhana, V. Chandra Mouli, Optical, physical and structural studies of
boro-zinc tellurite glasses, Phys. B Condens. Matter. 406 (2011) 1242–1247.
D
doi:10.1016/j.physb.2011.01.006.
TE
[42] S.M. Lima, A.A. Andrade, T. Catunda, R. Lebullenger, F. Smektala, Y. Jestin, et al., Thermal and
optical properties of chalcohalide glass, J. Non. Cryst. Solids. 284 (2001) 203–209.
doi:10.1016/S0022-3093(01)00403-3.
C
AC
Figure Captions
ACCEPTED MANUSCRIPT
Fig. 4 – Optical basicity (left) and Eletronic polarizability (right) as a function of TeO2 content
PT
Fig. 5 –Absorption coefficient of CBTx glasses
Fig. 6 - Left: Tauc’s plot of ℎ !/ vs photon energy for the indirect allowed transitions of CBTx
RI
glasses. Right: Estimated band gap values as functions of TeO2 content.
SC
Fig. 7 – dS/dT as a function of temperature of CBTx glasses
Table Captions
U
AN
Table 1 - Sample names and composition (wt and mol%), volumetric density (ρ), refractive index (n),
electronic polarizability (αm), theoretical optical basicity (Λth) and band gap (Eopt) of CBTx glasses.
M
D
TE
C EP
AC
ACCEPTED MANUSCRIPT
Table 1
Composition
Physical properties
CaF2 CaO B2O3 TeO2
PT
Sample wt% mol% wt% mol% wt% %mol wt% mol% ρ n αm (Å3) Ʌth Eopt (eV) dS/dT
-1
(.10-6 K-1)
RI
name (g cm ) (± 0.01) (± 0.03) (± 0.01)
(±0.03) (±0.5)
SC
@300K
CBT20 10.0 9.6 22.0 29.4 48.0 51.6 20.0 9.4 2.97 1.62 3.51 0.648 3.62 12.6
U
CBT25 10.0 9.9 20.0 27.7 45.0 50.2 25.0 12.2 3.04 1.64 3.65 0.656 3.55 -
AN
CBT30 10.0 10.3 18.0 25.9 42 48.6 30.0 15.2 3.14 1.65 3.71 0.664 3.47 -
CBT35 10.0 10.7 16 23.9 39 47.0 35.0 18.4 3.23 1.66 3.80 0.673 3.4 14.0
M
CBT40 10.0 11.2 14.0 21.8 36 45.1 40.0 21.9 3.32 1.68 3.94 0.683 3.33 -
D
CBT50 10.0 12.2 10.0 17.0 30.0 41.0 50.0 29.8 3.58 1.71 4.11 0.709 3.18 16.5
TE
C EP
AC
ACCEPTED MANUSCRIPT
PT
Fig.1 – Double column
RI
U SC
AN
M
D
TE
EP
C
AC
ACCEPTED MANUSCRIPT
TeO2
0 Glass
100
20
80
2
F
40
Ca
60
Te
O+
O2
Ca
60
PT
40
80
20
RI
100
0
CaO+CaF2 0 20 40 60 80 100 B2O3
SC
B2O3
U
AN
M
D
TE
EP
C
AC
ACCEPTED MANUSCRIPT
1.74 3.9
Refractive Index
3.8
1.72 Density
3.7
1.70 3.6
Refractive index n
Density (g cm-3)
3.5
1.68
3.4
PT
1.66 3.3
3.2
1.64
RI
3.1
1.62 3.0
2.9
SC
1.60
2.8
20 25 30 35 40 45 50
TeO2 content (wt%)
U
Figure 3 – Single column
AN
M
D
TE
C EP
AC
ACCEPTED MANUSCRIPT
4.2
0.72
CBTx glasses CBTx glasses
0.71 Linear fit 4.1 Linear fit
0.70
3.9
0.68
3.8
0.67
0.66 3.7
0.65 3.6
PT
0.64
3.5
0.63
20 25 30 35 40 45 50 20 25 30 35 40 45 50
TeO2 (wt%) TeO2 (wt%)
RI
Fig. 4 – Double column
U SC
AN
M
D
TE
C EP
AC
ACCEPTED MANUSCRIPT
2.0 CBT20 (a)
1.5
0.5
0.0
300 600 900 1200 1500 1800 2100 2400 2700
1.2
CBT20 (b)
PT
1.0 CBT25
CBT30
0.8 CBT35
CBT40
0.6
RI
CBT50
0.4
0.2
350 400 450 500
SC
Wavelength (nm)
U
AN
M
D
TE
C EP
AC
ACCEPTED MANUSCRIPT
2.5
CBT20 3.7
CBT25
CBT30
CBT40
(cm eV)
3.5
CBT50
-1
1.5
3.4
1/2
(Aehv)
3.3
1.0
3.2
PT
0.5
3.1
2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 20 25 30 35 40 45 50
hv (eV) TeO2 content (wt%)
RI
Fig. 6 – Double column
U SC
AN
M
D
TE
C EP
AC
ACCEPTED MANUSCRIPT
30
Data2_CBT20
Data3_CBT35
25 Data1_CBT50
Linear Fit
dS/dT (.10 K )
-1
20
-6
PT
15
10
RI
5
SC
300 320 340 360 380 400 420 440 460
Temperature (K)
U
AN
M
D
TE
C EP
AC