Professional Documents
Culture Documents
(Dust Suppression System
(Dust Suppression System
(Dust Suppression System
Previous Screen
Welcome: r461jlm1
Product: ROTARY DRILL
Model: MD6250 ROTARY DRILL DN8
Configuration: MD6250 Rotary Blasthole Drill DN800001-UP (MACHINE)
POWERED BY C27 Engine
Systems Operation
MD6250 Rotary Drill Systems
Media Number -M0074458-00 Publication Date -01/04/2019 Date Updated -29/04/2019
i07103860
Illustration 1 g06411309
(1) J1 Connector
(2) J2 Connector
The ECM bases decisions on input information and memory information. After the ECM receives the input and
outputs of the ECM are connected to the machine harness by two 70-pin connectors (1) and (2). The inputs and
outputs to the ECM can be viewed through the Caterpillar Electronic Technician (Cat ET).
Note: Only the complete ECM is serviceable (no lower-level components). The ECM must be replaced if the
ECM is damaged. Replace the ECM if a failure is diagnosed.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/mediasearch/mediaheaderinfoframeset.jsp&calledpage=/… 1/4
19/8/2019 MD6250 Rotary Blasthole Drill DN800001-UP (MACHINE) POWERED BY C27 Engine(M0087805 - 11) - Documentation
Pin Locations
Table 1
Auxiliary Machine Module 2 J1 Contact Descriptions
No. Type Function
55 PWM Driver Return Dust Curtain Raise / Lower Solenoid Return
58 PWM Driver Return Dust Curtain Raise Solenoid
59 PWM Signal Dust Curtain Lower Solenoid
Table 2
Auxiliary Machine Module 3 J1 Contact Descriptions
No. Type Function
48 PWM Driver Signal Dust Collector Air Filter Poppet Solenoid 1
49 PWM Driver Signal Dust Collector Air Filter Poppet Solenoid 2
50 PWM Driver Return Dust Collector Air Filter Poppet Solenoid Return 1-4
51 PWM Driver Signal Dust Collector Air Filter Poppet Solenoid 3
55 PWM Driver Return Dust Collector Air Flow / Air Filter Poppet Solenoid Return 1
58 PWM Driver Signal Dust Collector Air Filter Poppet Solenoid 5
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/mediasearch/mediaheaderinfoframeset.jsp&calledpage=/… 2/4
19/8/2019 MD6250 Rotary Blasthole Drill DN800001-UP (MACHINE) POWERED BY C27 Engine(M0087805 - 11) - Documentation
Illustration 2 g06285889
(1) Proximity Switch
The front and rear dust curtains are controlled by the Drill and Travel buttons on the right keypad. When in
travel mode, the dust curtains will automatically raise, and will lower while in drill mode. The dust curtains can
also be manually raised. The position of the curtains is determined by the dust curtain proximity switch (1) on
the rear dust curtain lifter.
Dust Collector
Illustration 3 g06372189
(2) Dust collector
(3) Directional valve
(4) Flushing valves
(5) Air valves
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/mediasearch/mediaheaderinfoframeset.jsp&calledpage=/… 3/4
19/8/2019 MD6250 Rotary Blasthole Drill DN800001-UP (MACHINE) POWERED BY C27 Engine(M0087805 - 11) - Documentation
Note: Only two control valves are shown. Machine is equipped with four valves total.
Air is supplied to the air manifold which supplies the electronic directional valves (3). The machine ECM sends
a signal to the directional valves which diverts air to one end of the air cylinder. The signal extends and retracts
the air cylinder which opens and closes the air valves (5). The air valves open drawing clean air into the suction
side of the dust collector filter. This short burst of air dislodges dust particles from the dust collector filter. Only
one filter is flushed at a time.
Copyright 1993 - 2019 Caterpillar Inc. Mon Aug 19 2019 21:48:26 GMT-0500 (hora estándar de Colombia)
All Rights Reserved.
r461jlm1
Private Network For SIS Licensees.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/mediasearch/mediaheaderinfoframeset.jsp&calledpage=/… 4/4