Professional Documents
Culture Documents
Mini Es p30b3 e r3 User Manual (一般)
Mini Es p30b3 e r3 User Manual (一般)
User Manual
DANGER!
Denotes an extraordinarily hazardous situation
This warning symbol indicates an immediate danger, which can lead to
severe injury or death.
Consult the warning
! WARNING!
Denotes a very dangerous situation
This warning symbol indicates a potentially Dangerous situation, which could
lead to severe injury or death.
Consult the warning
NOTICE!
Denotes a risk of material damage
This warning symbol indicates a situation that could lead to material
damage.
Consult the warning
1 Safety Requirements
1.1 Operating instructions
The operator must ensure that:
There is no flammables and explosives stored near the device
No nameplate is removed or no information on the nameplates is altered
The device is uncovered at any time
The device is not installed outdoor or in areas with direct solar radiation
The device is not installed on the ground with casual water
The device is not installed in bedroom or places for activities and rest by customers
No child touches the device
The device is unopened during operation
The temperature of rooms the device is installed in is kept at 25℃
The humidity of rooms the device is installed in is not greater than 95%
The device can only be placed on a firm enough surface
Any unclear warning and safety signage on the device must be replaced immediately
Transportation, assembly, installation and commissioning of the device can be implemented by the
authorized professionals only
Transportation, assembly, installation and commissioning of the device can be implemented only
under the specified conditions
The authorized staff shall be capable of evaluating the work distributed and identify the potential
risks in advance
Only the authorized and trained power engineers can perform the installation and commissioning,
and change the setting and connection of the device
Any potential hazards must be identified and necessary safety measures must be taken before
installation and operation
The debugging staff shall read and fully understood the safety instructions in the manual before
starting installation
The software, housing and components of the device cannot be changed without the manufacturer's
approval; otherwise, the liability and warranty will be invalid
The components cannot be opened without permission to cause damage to the seal. Otherwise, the
warranty will be invalid
The MINI ES shall be operated in line with the user manual, installation and service manual and
quality certificate. In the event of any damage to the device caused by nonconformity with the user
Build Your Dreams www.bydenergy.com
4
manual, installation and service manual and quality certificate, the liability and warranty will be
invalid
1.2 Installation qualification
The operator must be qualified electricians in local area who have ever accepted professional product
trainings in terms of:
Repair and removal of products
Protection and standard maintenance of devices in accordance with the safety standards
determined.
Offering assistance for the injured parties at the first time
Compliance with the local regulations, standards and management
DANGER!
Risk of fatal injury due to lack of assistance
A second person can Switch off the power supply and provide
assistance in an accident.
◆Only a second person is present could carry out work .
DANGER!
Risk of fatal injury due to disregarding safety
Instructions
If the safety instructions and/or the sequence of Steps for installation
are not followed, the product may be damaged permanently and
electrical Accidents with serious Personal injury may occur.
◆Consult the safety instructions
◆Notice the sequence of steps for installation
DANGER!
Risk of fatal injury from arcing
The arcing may occurs when the device has faults or breaker and
plugs are not used in specified manner.
◆Always use components in accordance with the instructions in their
respective manual
DANGER!
DANGER!
Risk of explosion due to the use of incorrect
battery types
If the battery which is used in the device is not approved, it may cause
explosion
◆Only use batteries that have been approved by the manufacturer
! WARNING!
Risk of injury due to lack of expertise
Installing and commissioning the storage system requires training, as
well as established expertise in electrical engineering.
Only the authorized、trained electricians could carry out the
installation、wiring and commission.
! WARNING!
Risk of injury due to heavy weight
The heavy weight of the components may cause injury during
installation, disassembly and transportation.
Transport and mount the components with two people
! WARNING!
Risk of injury due fail to follow the correct
sequence
If the specified sequence is not followed during installation, it may
cause injury or material damage
Consult the specified order
Consult the safety instructions
! WARNING!
Risk of injury due to sharp edges
The components have sharp edges which can cause Hand injuries if
you are not handled carefully.
Wear protective gloves
Mount the components with two people
! WARNING!
Risk of injury due to incorrect use of the
batteries
Eye and skin injuries caused by opening or damaging the batteries.
Never open or damage the batteries
! WARNING!
Don’t climbing equipment and laying sundries on the device.
Don’t decompound, renovate and repair the equipment.
Don’t do electrical maintenance to the internal of equipment. If
necessary, please contact with the agent.
Don’t touch the vent of the device. With board or plastic bags pack
the equipment is forbidden.
Don’t put any objects inside the equipment.
Don’t touch、tract and cut off the cable of the device.
Don’t set the device near heat source, such as the electric stove.
Don’t use wet cloth or potion ,such as diluents, to clean device
Don’t pull the power cord of the device.
Don’t touch the power supply with wet hand or cloth.
Don’t set the device near the high frequency machine、wireless
machine and machines which can send waves(radio and television).
Don’t hit and fell the equipment.
Don’t use spray to spray the equipment.
Don’t install the equipment in mute or a lot of noise.
Don’t connect the device that can’t work without external power
supply (such as desktop computer) to the system. There are many
differences between MINIES and UPS, for example, it could not
seamless switching without external power supply.
Don’t access power even after the completion of installation when
there are damages in equipment and parts , because it may cause
electric shock
2 Product Introductions
2.1 Appearance
◆ All the interfaces above must be connected by professional engineers with qualifications, and all
external devices connected must be authorized by BYD. In the event of any issues and damages due to
connection of other unauthorized devices, BYD will bear no liability and warranty service.
◆ Please refer to Installation Manual of MINI ES for the detailed connection methods
2.4 Operation interface
Long hold the “REMOTE” key and the The product is forced to be
REMOTE LOCAL POWER “LOCAL” key for about 5S charged and will power off
automatically after being fully
charged
Long hold the “REMOTE” key and the Forced charging of the product is
“LOCAL” key again for about 5S canceled
② CT2
③
CT1
①
④
⑤
⑥
⑧
Power P
Header
PV inverter box
CT1
Outdoor/
Grid
indoor
CT2
Load L&N&PE
Single-phase
inverter
Header
PV inverter box
CT1
Outdoor/
Grid
indoor
CT2
Load L&N&PE
Single-phase
appliance
Header
PV inverter box
CT1
Outdoor/
Grid
indoor
CT2
Load L&N&PE
Single-phase
appliance
Header
PV inverter box
RS485
CT
Outdoor/
Grid
indoor
General load
Important load
L&N&PE
General load distribution Essential load distribution L&N&PE
METER
board board
Power line
MINI ES
Signal wire
3 Product Registrations
注:实现此功能,需要连接用户网络,获取产品相关数据,客户和厂商监控产品运行状态,以便提供更好
的服务和反馈。
3.1 Registration on APP
Download the APP application software “BYD Energy System” first and register the product
according to the message prompted of APP.
Android phone users IOS phone users
Search the “BYD Storage System” on “Google Click “Search” on App Store and enter “BYD Energy
Build Your Dreams www.bydenergy.com
17
Market”. Storage Monitoring” in search bar.
4 Other Instructions
4.1 Product list
Check the scope of delivery after taking out the energy system. In the event of any loss or damage to the
components, please contact us. The following components are included during delivery
No. Name Quantity Description
1 MINI ES 1 set
2 Current transducer 2 Pcs. With 10M cable
3 User Manual 1
4 Test Report 1
No littering
Grounding point
Heating sign
About BYD
For any assistance about BYD product, please contact BYD by:
Electric Power Research Institute
BYD Auto Industry Company Limited
NO. 3009, BYD Road, Pingshan, Shenzhen, 518118, P.R.China
Tel:+86 0755-89888888 - 57860