Professional Documents
Culture Documents
Made Easy 16 Full 4 PDF
Made Easy 16 Full 4 PDF
Made Easy 16 Full 4 PDF
MY PROFILE
REPORTS
BUY PACKAGE
Solution Report For Full Syllabus Test4 : Basic Level
Represent whole test solution with correct and incorrect answers.
NEWS View Your Test Analysis
Ask an Expert
Q. Question Status
No
Q.1
Choose the option which can replace the idiom/phrase underlined in the
sentence given below: Communicative English is the Achilles’ heel for
job aspirants more so for engineering students.
a. source of strength
b. weak spot
c. what they like the most
d. top priority
Q.2
Choose the option which is similar in meaning to RICOCHET.
a. gallop
b. materialise
c. snigger
d. rebound
Q.3
Identify the option in which the underlined word has been used in the
http://s3.onlinetestseriesmadeeasy.in/madeeasy/index.php?pageName=timeManagementReport&testid=597&t=a&testType=2 1/19
2/5/2016 MADE EASY ONLINE TEST SERIES
most appropriate manner:
a. Since he intends to settle down in India, he is leaving Singapore
temporarily.
b. Since he intends to settle down in India, he is leaving Singapore
immediately.
c. Since he intends to settle down in India, he is leaving Singapore
urgently.
d. Since he intends to settle down in India, he is leaving Singapore
permanently.
Q.4
Given below are some terms of a series made by using alphabets, Find
the term which will come in the last place.
AZ, CX, FU, IR, KP, ?
a. MN
b. NM
c. OP
d. NN
Q.5
A rectangular sheet ABCD having side AB = 14 cm and side BC = 28 cm
is rolled to form a right circular cylinder. Initially, the sheet is rolled along
side AB to form a cylinder C1 with height = 28 cm and then the sheet is
rolled along side BC to form a cylinder of smaller height to form cylinder
C2. By what percent is volume of bigger cylinder more than the volume
of the smaller cylinder?
Q.6
Identify the option which fills in the blanks to make a meaningful
sentence:
The task is made difficult by the fact that a/an ________ investigation of
the improvement in energy ________ and ______ effect has to face
three conceptual problems yet to be fully explored.
a. efficiency, empirical, conceptual
b. conceptual, efficiency, rebound
c. empirical, rebound , efficiency
http://s3.onlinetestseriesmadeeasy.in/madeeasy/index.php?pageName=timeManagementReport&testid=597&t=a&testType=2 2/19
2/5/2016 MADE EASY ONLINE TEST SERIES
d. empirical, efficiency, rebound
Not Attempt Correct Ans. d
Video Solution FAQ? Have any doubt? Solution
Q.7
Which of the following has a value equivalent to the following expression:
a.
b. 1
c.
d. 100
Q.8
A group of boys and girls know either Hindi or English. The number of
boys and girls are in the ratio 1 : 3. 20% of the girls know English and the
rest of them know Hindi. On the other hand, 48% of the boys know
English and the rest of them know Hindi. A student is chosen at random
from the group of students who knows English. What is the probability
that the chosen student is a girl?
a.
b.
c.
d.
Not Attempt Correct Ans. b
Video Solution FAQ? Have any doubt? Solution
Q.9
f (x) is a polynomial function of second degree such that f (–3) = 6, f (0) =
6 and f (2) = 11. What is the point at which the graph of this function
intersects a line drawn parallel to y axis through x = 1?
http://s3.onlinetestseriesmadeeasy.in/madeeasy/index.php?pageName=timeManagementReport&testid=597&t=a&testType=2 3/19
2/5/2016 MADE EASY ONLINE TEST SERIES
a. (1,–2)
b. (1, 4)
c. (1, 6)
d. (1, 8)
Q.10
A square and a regular octagon have identical perimeter. The ratio of the
areas of the octagon and the square is _____________.
Q.11
A circular alloy bar 2 m long uniformly topers from 30 mm diameter to
20 mm diameter. The elongation of the rod under on axial force of 50 kN
will be
[Take E for the alloy as 140 GPa]
a. 1.51 mm
b. 2.64 mm
c. 3.56 mm
d. 4.62 mm
Q.12
For a parallel load on a fillet weld of equal legs, the plane of maximum
shear occurs at
a. 22.5°
b. 30°
c. 45°
d. 60°
Q.13
The coefficient of friction between two surfaces is the constant of
proportionality between the tangential force and normal reaction at the
instant of
a. application of force
http://s3.onlinetestseriesmadeeasy.in/madeeasy/index.php?pageName=timeManagementReport&testid=597&t=a&testType=2 4/19
2/5/2016 MADE EASY ONLINE TEST SERIES
b. impending motion
c. body is in motion
d. body is at rest
Q.14
It is given that the actual demand is 59 units, a previous forecast 64
units and smoothing factor 0.3. What will be the forecast for next period,
using exponential smoothing ?
a. 36.9 units
b. 57.5 units
c. 60.5 units
d. 62.5 units
Q.15
In steam and other vapour cycle, the process of removing non
condensable is called
a. scavenging process
b. deaeration process
c. exhaust process
d. condensation process
Q.16
Which of the following phase of steel is not present in Ironcarbon phase
diagram ?
a. Ferrite
b. Cementite
c. Austenite
d. Martensite
Q.17
A gear train in which axes of gears have motion are called
a. Epicylic gear trains
http://s3.onlinetestseriesmadeeasy.in/madeeasy/index.php?pageName=timeManagementReport&testid=597&t=a&testType=2 5/19
2/5/2016 MADE EASY ONLINE TEST SERIES
b. Simple gear trains
c. Compound gear trains
d. Compound gear trains
Q.18
A ring gauge is used to measure
a. Outside diameter but not roundness
b. Roundness but not outside diameter
c. Both outside diameter and roundness
d. Only external threads
Q.19
Ornamental objects, statues, toys etc. are cast by
a. Die casting
b. Pressed casting
c. Centrifugal casting
d. Slush casting
Q.20
A single cylinder, 4 stroke engine is fitted with a rope brake. The
diameter of the brake wheel is 600 mm and the rope diameter is 30 mm.
The dead weight on the brake is 200 N and the spring balance reads 30
N. If the engine runs at 450 rpm. What is the brake power of the engine ?
a. 0.424 kW
b. 2.53 kW
c. 3.56 kW
d. 1.53 kW
Not Attempt Correct Ans. b
Video Solution FAQ? Have any doubt? Solution
Q.21
http://s3.onlinetestseriesmadeeasy.in/madeeasy/index.php?pageName=timeManagementReport&testid=597&t=a&testType=2 6/19
2/5/2016 MADE EASY ONLINE TEST SERIES
rod at a rate of 10 kW. The irreversibility rate for the rod is [Take T0 =
300 K]
a. 3 kW
b. 4 kW
c. 5 kW
d. 6 kW
Q.22
The shape factor F21 in diagonal partition within a long square duct
(shown in figure) is
a. 0.71
b. 0.61
c. 0.41
d. 0.36
Not Attempt Correct Ans. a
Video Solution FAQ? Have any doubt? Solution
Q.23
The temperature distribution associated with radial conduction through a
sphere with no internal heat generation is given by
a. Parabola
b. Hyperbola
c. Logarithmic curve
d. Straight line
Q.24
The value of is
http://s3.onlinetestseriesmadeeasy.in/madeeasy/index.php?pageName=timeManagementReport&testid=597&t=a&testType=2 7/19
2/5/2016 MADE EASY ONLINE TEST SERIES
a. e[e + 1]
b. e2 + 1
c. e + e –1
d. does not exists
Q.25
The probability that exactly one of the two events A, B occurs can’t be
expressed by
(i) P(A) + P(B) – 2P(A ∩ B)
(ii) P(A ) + P (B) – 2P (A ∩B)
(iii) P(A ∩ B) + P (A ∩ B)
a. (i) and (ii) only
b. (ii) and (iii) only
c. (i) and (iii) only
d. (i), (ii) and (iii)
Q.26
A cantilever of 2 m span carries a triangular load of zero intensity at the
free end and 100 kN/m at the fixed end. The deflection at the free end will
be __________ mm.
Q.27
A circular opening 6 m in diameter, in a vertical side of a tank is closed
by a disc of 6 m diameter which can rotate about a horizontal diameter.
The head of water above horizontal diameter is 8 m. The force on the
disc will be _______ kN.
Q.28
Oxygen to acetylene ratio in case of neutral flame by weight is
http://s3.onlinetestseriesmadeeasy.in/madeeasy/index.php?pageName=timeManagementReport&testid=597&t=a&testType=2 8/19
2/5/2016 MADE EASY ONLINE TEST SERIES
___________.
Q.29
The total number of instantaneous centres of a mechanism have 5 link is
________.
Q.30
A local heat transfer coefficient hx for flow over a flat plate is given by hx
Where = average heat transfer coefficient
Q.31
Air is heated as it flows at steady state through a constant area duct. At
the inlet, the temperature is 300 K, the pressure is 2 bar and velocity is
87 m/s. At the exit the pressure and velocity are 1.45 bar and 360 m/s
respectively. Then heat transfer per unit mass for the process will be
_________ kJ/kg.
Q.32
In an ideal refrigeration (reversed Carnot) cycle, the condenser and
evaporator temperature are 27°C and – 13°C respectively. The COP of
this cycle would be ___________.
Q.33
Time estimates of a project activity are:
http://s3.onlinetestseriesmadeeasy.in/madeeasy/index.php?pageName=timeManagementReport&testid=597&t=a&testType=2 9/19
2/5/2016 MADE EASY ONLINE TEST SERIES
Optimistic time, (t0 ) = 10 days
Most likely time, (tm) = 15 days
Pessimistic time, (tp) = 22 days
Variance in days for the activity as per beta distribution is
____________.
Q.34
The area bounded by the lines = 1 is __________ sq. unit.
Q.35
poles is_____.
Q.36
A plane element is subjected to the stresses shown in figure. The
principal stresses will be
a. σmax = 113.3 MPa, σmin = 88.3 MPa
b. σmax = 113.3 MPa, σmin = – 88.3 MPa
c. σmax = 113.3 MPa, σmin = 44.6 MPa
d. σmax = 113.3 MPa, σmin = – 44.6 MPa
Not Attempt Correct Ans. b
Video Solution FAQ? Have any doubt? Solution
http://s3.onlinetestseriesmadeeasy.in/madeeasy/index.php?pageName=timeManagementReport&testid=597&t=a&testType=2 10/19
2/5/2016 MADE EASY ONLINE TEST SERIES
Q.37
A sleeve, in which a shaft of diameter 75 mm, is running at 1200 rpm, is
having a radial clearance of 0.1 mm. If the length of sleeve is 100 mm
and the space is filled with oil of dynamic viscosity 0.96 poise, then what
will be the torque resistance ?
a. 3.996 Nm
b. 4.996 Nm
c. 5.996 Nm
d. 6.996 Nm
Q.38
A wheel of radius 450 mm is made to roll without slipping by pulling a
string with velocity V. If the centre of the wheel moves with a velocity of
3 m/s, the velocity of string. Which is wound over a drum of radius 0.3 m
as shown will be
a. 1 m/s
b. 2 m/s
c. 2.5 m/s
d. 3 m/s
Q.39
Regarding the correlation coefficient, which of the following statement is
true ?
a. If correlation coefficient (r ) is positive, it means that a certain percentage
of data points are in close proximity with the trend line and the line is
sloping downward.
b. If correlation coefficient (r ) is negative, it means that all the percentage
of data points are in close proximity with the trend line and the line is
sloping upward.
c. If correlation coefficient (r ) is positive, it means that a certain
percentage of data points are in close proximity with the trend line and
the line is sloping upward.
d. If the correlation coefficient (r ) is zero, all the data points perfectly
http://s3.onlinetestseriesmadeeasy.in/madeeasy/index.php?pageName=timeManagementReport&testid=597&t=a&testType=2 11/19
2/5/2016 MADE EASY ONLINE TEST SERIES
coincide with the trend line.
Q.40
In a ideal Brayton cycle, air is compressed from 100 kPa and 25°C to 1
MPa, and then heated to 927°C before entering the turbine. Under cold
air standard conditions, the air temperature at the turbine exit is
a. 349°C
b. 426°C
c. 622°C
d. 733°C
Q.41
In the diagram given below, the magnitude of absolute angular velocity of
link 2 is 10 radian per second while that of link 3 is 6 radian per second.
What is the magnitude angular velocity of link 3 relative to 2?
a. 6 radian per second
b. 16 radian per second
c. 4 radian per second
d. 14 radian per second
Q.42
a. 80 V and 150 A
b. 40 V and 300 A
c. 40 V and 150 A
d. 80 V and 300 A
Q.43
A wide strip is rolled to a final thickness of 6.35 mm with a reduction of
40 percent. The roll radius is 50 cm and coefficient of friction is 0.3. Then
angle of contact is
a. 0.092 radians
b. 0.0738 radians
c. 0.0123 radians
d. 0.0235 radians
Q.44
ListI ListII
A. Hot chamber machine 1. Cleaning
B. Muller 2. Core making
C. Dielectric baker 3. Die casting
D. Sand blaster 4. Annealing
5. Sand mixing
Codes:
A B C D
(a) 2 1 4 5
(b) 4 2 3 5
(c) 4 5 1 2
(d) 3 5 2 1
a. a
b. b
c. c
d. d
Q.45
http://s3.onlinetestseriesmadeeasy.in/madeeasy/index.php?pageName=timeManagementReport&testid=597&t=a&testType=2 13/19
2/5/2016 MADE EASY ONLINE TEST SERIES
a. 1, 2, 3, 4
b. 2, 3, 1, 4
c. 2, 1, 3, 4
d. 3, 2, 1, 4
Not Attempt Correct Ans. a
Video Solution FAQ? Have any doubt? Solution
Q.46
A mass of 0.25 kg of an ideal gas has a pressure of 300 kPa,
temperature of 80°C, and a volume of 0.07 m3 . The gas undergoes an
irreversible adiabatic process to a final pressure of 300 kPa and final
volume of 0.10 m3 , during which the workdone on the gas is 25 kJ. Then
the increase in entropy of gas is
a. 0.08 kJ/K
b. 1.06 kJ/K
c. 0.06 kJ/K
d. 1.33 kJ/K
Q.47
The rate of heat transfer between a certain electric motor and its
surroundings varies with time as = – 0.2[1 –e–0.5t] where ‘t ’ is in
seconds and
is in
kW. The shaft of the motor rotates at a constant
speed of 100 rad/sec and applies a constant torque of 18 Nm to an
external load. The motor draws a constant electric power input of 2 kW.
Find the rate of change of energy of the motor
a. – 0.4 + 0.2e–0.5t
b. 1.8 + 0.2e–0.5t
c. 0.2e–0.5t
d. – 4 + 0.2e–0.5t
Q.48
A spark ignition engine has a compression ratio of 8 and the volume
before compression is 0.9 m3 /kg. Net heat interaction per cycle is 1575
kJ/kg. What is the mean effective pressure ?
a. 20 kPa
b. 20 bar
http://s3.onlinetestseriesmadeeasy.in/madeeasy/index.php?pageName=timeManagementReport&testid=597&t=a&testType=2 14/19
2/5/2016 MADE EASY ONLINE TEST SERIES
c. 200 Pa
d. 2 bar
Q.49
In a food processing plant, a brine solution is heated from – 12°C to –
6.5°C in a double pipe parallel heat exchanger by water entering at 35°C
and leaving at 20.5°C at the rate of 9 kg/min. What is the heat exchanger
area for an overall heat transfer coefficient of 860 W/m2 K. Use (Cp)water
= 4.186 kJ/kgK
a. 0.586 m2
b. 0.293 m2
c. 1.172 m2
d. 12.93 m2
Q.50
A 3 × 3 square matrix is given as
Sum and product of eigen values are respectively __________ and
__________ .
a. –9, 21
b. 5, 21
c. –5, 21
d. 9, –5
Q.51
Find the solution of differential equation
Here f (x) is an exclusive function of ‘x’ and f′(x) is derivative of function f
(x) with respect to x.
a. f (x) + log(f (x) + 1) = C
b. f (x) + log(f (x) + y) = C
c. f (x) + log(y) = C
d. f (x) + log(1 + y – f (x)) = C
http://s3.onlinetestseriesmadeeasy.in/madeeasy/index.php?pageName=timeManagementReport&testid=597&t=a&testType=2 15/19
2/5/2016 MADE EASY ONLINE TEST SERIES
Q.52
A steel bar 3 m long and 2500 mm2 in area hangs vertically, which is
securely fixed on a collar at its lower end. If a weight of 15 kN falls on the
collar from a height of 10 mm, the strain energy stored in the bar will
be_____________ Nm. [Take E as 200 GPa]
Q.53
A thin cylindrical pressure vessel of 1.2 m diameter generate steam at a
Q.54
Water is flowing through a pipe of 5 cm diameter under a pressure of 35
N/cm2 (gauge) and with a mean velocity of 5 m/s. At a crosssection, 10
m above the datum line, the total energy per unit weight of the water will
be __________m.
Q.55
Jobs arrives at a facility at an average rate of 5 in an 8 hour shift. The
arrival of the jobs follow Poisson distribution. The average service time
of a job on the facility is 40 minutes. The service time follows exponential
distribution. Idle time at the facility per shift will be ___________ hours.
Q.56
A 280 mm diameter cylinder fitted with frictionless leak proof piston
contains 0.02 kg of steam at a pressure of 0.6 MPa and a temperature of
200°C. As the piston moves slowly outwards through a distance of 305
http://s3.onlinetestseriesmadeeasy.in/madeeasy/index.php?pageName=timeManagementReport&testid=597&t=a&testType=2 16/19
2/5/2016 MADE EASY ONLINE TEST SERIES
steam pressure P and steam volume V are related by PVn = constant. If
the final pressure of steam is 0.12 MPa, then the value of exponent is
__________.
[At 0.6 MPa and 200°C, v = 0.352 m3 /kg, h = 2850.1 kJ/kg]
Q.57
For the process shown in figure, sensible heat factor is _____________.
Q.58
In a singlepoint turning operation of steel with cemented carbide tool,
the Taylor’s tool life exponent is 0.25. If cutting speed is halved, then tool
life will increased by __________times.
Q.59
When copper is electrochemically machined under following conditions
ΔV = 18 V
I = 500 A
Atomic weight = 56
Valency = 2
Density(ρ) = 7.8 g/cm3
then the MRR by electrochemical process is ________(cm3 /min).
http://s3.onlinetestseriesmadeeasy.in/madeeasy/index.php?pageName=timeManagementReport&testid=597&t=a&testType=2 17/19
2/5/2016 MADE EASY ONLINE TEST SERIES
Q.60
A spur gear has 30 teeth and module of 1.4 mm. It rotates at 360 rpm
than the value of pitch line velocity in mm/min is __________.
Q.61
What will be the natural frequency of the system shown below
_________ Hz.
Q.62
In a flow over flat plate, water with velocity 6 m/s and stanton number =
0.3096 × 103 , if velocity is doubled with stanton number remaining
constant. Then the new heat transfer coefficient will be _________
W/m2 K.
Use ρ = 1000 kg/m3
K = 4.2 W/mk
Cp = 4.18 kJ/kgK
Q.63
A gas of 4 kg is contained within a pistoncylinder machine. The gas
undergoes a process for which PV1.5 = constant. The initial pressure is 3
bar and initial volume is 0.1 m3 , and the final volume is 0.2 m3 . The
specific internal energy of the gas decreases by 4.6 kJ/kg. There is no
http://s3.onlinetestseriesmadeeasy.in/madeeasy/index.php?pageName=timeManagementReport&testid=597&t=a&testType=2 18/19
2/5/2016 MADE EASY ONLINE TEST SERIES
significant changes in K.E. and P.E. The magnitude of net heat transfer
for the process is __________ kJ.
Q.64
A matrix of order 2 × 2 is made with the elements 0 and 1 only. The
probability that the determinant is nonnegative is_____.
Q.65
given by k2πi. The value of k is_____.
http://s3.onlinetestseriesmadeeasy.in/madeeasy/index.php?pageName=timeManagementReport&testid=597&t=a&testType=2 19/19