Professional Documents
Culture Documents
2012 Pump Catalog
2012 Pump Catalog
For More Pump Choices See Our Product Index in the Back of this Catalog
CENTRIFUGAL:
Self-Priming or Non Self-Priming Designs. Good for Abrasive Liquids. Ideal for Spraying or Transfer.
High Flows, Low Pressures (to 150 psi). Ag/Turf Spraying, Transfer, Irrigation, Recirculation,
Petroleum. Electric Motor, Gas Engine, PTO or Hydraulic Driven.
DRUM:
Mounts to Drums or Pails for Fluid Transfer. Many Different Designs for a Wide Variety of
Applications. Electric Motor (110 volt or 12 volt), Hand Driven and Air Operated.
FLEX IMPELLER:
Inexpensive Transfer Pumps. Low Flow, Low Pressure. Ideal for Transfer, Dewatering, Recirculation
or Mixing Applications. Electric Motor Driven.
GEAR:
Excellent for transfer of highly viscous (clear) liquids at medium pressures (to 300 psi). Ideal for
Petroleum and Industrial fluids. Electric Motor Driven.
PISTON/PLUNGER:
High Pressure, Positive Displacement Design. Ideal for Pressure Wash, Car Wash, Industrial
Cleaning Applications. Electric Motor, Gas Engine or PTO Driven.
ROLLER:
Inexpensive, Medium Pressure (100-300 psi). Transfer & Spraying Pumps. Ideal for Agricultural
and Turf Spraying of Herbicides & Pesticides. Usually PTO or Gas Engine Driven.
SUBMERSIBLE:
Centrifugal Design. Sumps Pumps for Liquid Removal or Dewatering of Pits or Tanks or for use
in Recirculation, Fountains, etc. Electric Motor Driven.
VACUUM:
Excellent Choice for Slurry Tankers or Suction Units at Intermittent use.
D D
FLOMAX 5, 8 & 10
FLOMAX 15
80 80 110
HQ HQ
70 HQ 100
70
90
60 60 80
NPSH
NPSH
50
BH P
BH P
50 70
BH P
40 60
NPSH
40
3 30 3 30 50
30 30 40 8
2 20 2 20 30 6 30
20 20 4 20
1 10 1 10 20
10 10 2 10
10
0 20 40 60 80 100 120 140 0 20 40 60 80 100 120 140 160 180 0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 320
100 DU MP4030 *8 140 110 1.0 2" 3 208/230/460 3 5.0" 125 1640.00
90 DU MP3510 8 140 110 1.7 2" 5 230 1 5.0" 165 1355.00
80 DU MP3510W *8 140 110 1.7 2" 5 230 1 5.0" 165 1886.00
70
DU MP3530 8 140 110 1.7 2" 5 208-230/460 3 5.0" 145 1225.00
DU TK3530W-A * - 170 85 1.7 2" 5 208-230/460 3 5.0" 150 1438.00
BH P
60
DU MP3530W *8 140 110 1.7 2" 5 208-230/460 3 5.0" 145 1767.00
NPSH
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0217
Self-Priming Centrifugal Pumps 97
FLOMAX Close Coupled Electric Motor Driven Pumps Cast Iron Construction
Self Priming • Centrifugal • Cast Iron Construction Cast Iron Impeller
Pumps are of cast iron construction to suit a wide variety of liquids. All fasteners are stainless steel to reduce Stainless Steel Shaft Sleeve
corrosion. Impellers are balanced and trimmed to insure non-overloading conditions. Standard Stainless Steel and
Viton® Ceramic Seals
Viton® mechanical seal is self-adjusting and corrosion resistant to handle many different liquids. Pump assemblies
are offered with TEFC motors, or as PUMP PAKS only to fit customer’s standard motor. Stainless Fasteners
D
D
FLOMAX 10
FLOMAX 5
FLOMAX 8
FLOMAX 10
2" X 2"
Self-Priming Pump
FLOMAX 8 3450 RPM S.G. = 1.0
2" X 2"
FLOMAX 5 Self-Priming Pump
1-1/2" X 1-1/2" 3450 RPM S.G. = 1.0
Self-Priming Pump
3450 RPM S.G. = 1.0
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0218
98 Self-Priming Centrifugal Engine Pumps
Gasoline Engine Driven MODEL FLOMAX 5
SIZE 1-1/2 X 1-1/2
MODEL FLOMAX 8
SIZE 2 X 2
IMPELLER DIA. 5.00 IMPELLER DIA. 5.00
Centrifugal Pump Units MAX. SOLIDS 0.56 DIA. MAX. SOLIDS 0.56 DIA.
SUCTION LIFT
SUCTION LIFT
dultmeier.com
FLOMAX
“Pump Packs”
for Engines
These pump packs can be mated to
Briggs & Stratton, Honda, Tecumseh
D
or PowerPro engines. They may be
assembled with the electric or manual
clutch pedestal units.
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0219
Flomax Self-Priming Centrifugal Pumps 99
FLOMAX 5 - 1-1/2"
FLOMAX PEDESTAL PUMPS
1-1/2" • 2" • 3"
Shaft Wt.
Part No. Series Ports Construction Diameter Lbs. Net Ea.
MX 21312 FLOMAX 5 1-1/2" FPT Cast Iron 3/4" 44 $ 296.56
MX 21339 FLOMAX 8 2" FPT Cast Iron 3/4" 44 355.00
MX 33961 FLOMAX 8 2" FPT #Cast Iron with Double Seal 3/4" 44 1015.86
MX 21363 FLOMAX 10 2” FPT Cast Iron 1” 85 610.00
MX 21381 FLOMAX 15 3" FPT Cast Iron 1" 85 610.00
MX 32031 FLOMAX 15 3" FPT #Cast Iron with Double Seal 1" 85 1429.66
# Model 33961 & 32031 have Double Seal - Can be run dry - or be used with abrasive materials.
Also available for C-Face or Engine Drive - See previous page. FLOW GPM (Q)
MP PUMPS FLOMAX 10
Hydraulic Motor Drive FLOMAX MODEL FLOMAX 10
INTERMITTENT DUTY SIZE 2 X 2
Pedestal Pump 2" & 3" IMPELLER DIA. 5.75
15 GPM OIL FLOW MAX. SOLIDS .56
Self-Priming - Centrifugal Sizes
TOTAL HEAD-FEET
FLOMAX 15 FLOMAX
INTERMITTENT DUTY MODEL FLOMAX 15 10 & 15
SIZE 3 X 3
15 GPM OIL FLOW IMPELLER DIA. 5.75
MAX. SOLIDS .56
GALLONS PER MINUTE C/N 7029
TOTAL HEAD-FEET
FLOMAX Hydraulic Driven self-priming centrifugal pumps are capable of pumping a wide
OIL PRESSURE - PSI
variety of liquids at capacities up to 300 GPM, heads to 130 feet and lifts to 25 feet. Cast iron with
removable flanges, replaceable wear plates and S.S. fasteners are standard. (S.S. Available).
MP Hydraulic Motor Units can also be adapted to Flomax Pumps that are equipped with the
proper mounting attachments; call with pump model numbers.
Note: Your hydraulic system must match hydraulic motor specifications shown below
— DO NOT OVERSPEED.
Viton® is a registered trademark of DuPont Performance Elastomers
FLUID FLOW GPM (Q) C/N 7030
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0220
100 MP Flomax Centrifugal Pump Parts
MP Flomax PUMPS
COMPOSITE PARTS LIST
Flomax 5 & 8 • Flomax 10 & 15
CAST IRON MODELS ONLY
MP /
F
9 Repa lomax P
ir Av um
ailab p
24 le
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0221
Self-Priming Centrifugal Pumps 101
• Patented Vac-U-Double Seal design eliminates pressure on the seal • Cast iron heavy wall section provides extended life to unit.
resulting in long seal life. • Total Dependability and Versatility.
• Closed type hydraulically balanced impeller eliminates thrust loads for • Designed for Many Chemicals and Fertilizers.
increased bearing life. Wear actually improves impeller efficiency.
• Speeds to 3500 RPM.
• No adjustments of impeller necessary with shims.
• 2 Year Unconditional Warranty on Pump.
• Pump can be operated DRY without damaging the seal.
D Gasoline
Engine
Straight Model
D
Self Priming Centrifugal
D
Centrifugal Pedestal
Pump
S3220 Straight 2" Pump SP3220 Self Priming 2" Pump SP3320 Self Priming 3" Pump S3325P Straight 3" Truck Pump
• Double Viton® Wet Seal • Double Viton® Wet Seal • Double Viton® Wet Seal • Double Viton® Wet Seal
• 197 Maximum GPM • 152 Maximum GPM • 308 Maximum GPM • 463 Maximum GPM (at 4500 RPM)
• 39 Maximum PSI • 42 Maximum PSI • 65 Maximum PSI • 99 Maximum PSI
• 3500 Maximum RPM • 3500 Maximum RPM • 3500 Maximum RPM • 4500 Maximum RPM
• 5 HP • 5 HP • 7.5-15 HP • 16.5 HP
• 2" FPT • 2" FPT • 3" FPT • 3" FPT
• Electric, Gas, Hydraulic • Electric, Gas, Hydraulic • Electric, Gas • PTO Drives
Max. Max.
BARE PUMPS WITH PEDESTAL MOUNT FOR LONG COUPLED DRIVE BASE MTD. LONG COUPLED MOTOR PUMP UNITS Spec. Flow
Part No. Description Wt. Grav. GPM Net Ea.
Max. Flow DU BU3510S 2” 5 HP/1PH Straight/Long Coupled 150 lbs. 1.4 195 $ 1807.00
Part No. Description GPM Wt. Net Ea. DU BU3530S 2” 5 HP/3PH Straight/Long Coupled 145 lbs. 1.4 195 1679.00
BU S3220P 2" Straight Pump 3/4" ............. 197 44 lbs. $ 850.00 DU BU3530 2" 5 HP/3PH Self Prime/Long Coupled 150 lbs. 1.4 152 1733.00
BU SP3220P 2" Self Priming Pump 3/4" ...... 152 71 lbs. 955.00 DU BU7533 3" 7.5 HP/3PH Self Prime/Long Coupled... 250 lbs. 1.0 308 2148.00
BU S3320P 3" Straight Pump 1-1/8"........... 365 120 lbs. 1003.00 DU BU1031A 3" 10 HP/1PH Straight/Long Coupled........ 280 lbs. 1.3 365 2567.00
BU SP3320P 3" Self Priming Pump 1-1/8" ... 308 114 lbs. 1134.00 DU BU1033 3" 10 HP/3PH Self Prime/Long Coupled.... 280 lbs. 1.4 308 2525.00
BU S3325P 3" Straight Truck Pump 1-1/8".. *463 125 lbs. 1195.00 DU BU1031 3” 10 HP/1PH Self Prime/Long Coupled... 280 lbs. 1.4 308 2794.00
BU SP3325P 3” Self Prime Truck Pump 1-1/8” **308 130 lbs. 1439.00 DU BU1533 3" 15 HP/3PH Self Prime/Long Coupled.... 320 lbs. 1.6 308 2833.00
* 463 GPM at 4500 RPM for Straight Truck Pump. DU BU1533A 3" 15 HP/3PH Straight/Long Coupled........ 300 lbs. 1.6 365 2669.00
** 308 GPM at 3500 RPM for 3” Self-Priming Truck Pump. Max. Max.
PUMPS WITH HYDRAULIC DRIVE Max. Flow GAS DRIVEN PUMP UNITS Spec. Flow
Part No. Description GPM Net Ea. Part No. Description Wt. Grav. GPM Net Ea.
BU S3325-PH 3" Straight, Hydraulic Drive 365 $ 1313.00 BU SP3220 2" SP Pump only for 3/4" Gas Engine Drive. 62 lbs. - 150 $ 680.00
BU SP3325-PH 3" Self Priming, Hydraulic Drive 308 2216.00 DU BU25GH 2" Straight/5.5 HP Honda............................ 105 lbs. 1.4 197 881.00
DU BU25GHSP 2" Self Priming/5.5 HP Honda..................... 160 lbs. 1.4 150 1168.00
Max. Max. DU BU25PP 2" Self Priming/5.5 HP PowerPro................ 105 lbs. 1.4 150 903.00
CLOSE COUPLED MOTOR PUMP UNITS Spec. Flow DU BU313PP 3" Self Priming/13 HP PowerPro................. 210 lbs. 1.6 308 1576.00
Part No. Description Wt. Grav. GPM Net Ea. DU BU313PPE 3" Self Priming/13 HP PowerPro/Elec. Start 210 lbs. 1.6 308 1576.00
BU S3320E15T 3" 15 HP/3PH Straight/Close Cpld 350 lbs. 1.6 463 $ 1585.00 BU SP3320BS 3" SP Pump Only for 1" Gas Engine Drive.... 92 lbs. - 308 862.00
BU SP3320E15TB 3" 15 HP/3PH Self Prime/Close Cpld 463 lbs. 1.6 463 1988.00 DU BU311GHE 3" Self Priming/11 HP Honda/Electric Start. 190 lbs. 1.4 308 1803.00
Viton® is a registered trademark of DuPont Performance Elastomers DU BU311GH 3" Self Priming/11 HP Honda......................... 190 lbs. 1.4 308 1593.00
DU BU313GHE 3" Self Priming/13 HP Honda/Electric Start. 210 lbs. 1.6 308 1757.00
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0228
102 Centrifugal Transfer Pumps
316SS Stainless Self-Priming Pump Units
An excellent choice for pumping Pressureseal Pumps ®
PSE 303
many chemicals compatible Made to provide trouble-free performance
with 316 stainless steel. These with any liquid. Pumps will run dry
pump units consist of 2” x 2” self- without seal problems. Pump and
priming pumps constructed Lucite Expansion Tank are factory
assembled with 50% Ethylene Glycol
of 316 cast stainless steel and pressurized to 125 PSI. Pumps are
(more durable than stamped straight or self-priming and available in
stainless pumps). Elastomers are pedestal, clutch or electric motor drive. Cast D
Viton® or EPDM depending upon iron construction with sealed bearings and double
chemical compatibility. Pumps are long- viton mechanical pressure seal. Pumps should oper-
ate at 3600 RPM. Note: Follow maintenance instructions
coupled to Totally Enclosed, Fan Cooled
on the pressure seal system.
(TEFC) motors (1 or 3 Phase). Heavy duty steel
base plates and coupling guards with powder coat SCOT Pressure Seal Pumps with 3 Phase TEFC Motor Drive, Base
paint finish. Call for chemical compatibility check. Plate, Guard and Lovejoy Couplings.
Max. GPM Wt.
316 SS Pump Units Max. Wt. Part No. S.G. @20 PSI Motor Lbs. Net Ea.
Part No. HP Phase Elastomer S.G. Lbs. Net Ea. DU PSE303-53 3x3 Straight 1.0 SG 250 5 HP, 3 PH 230 $ 2065.00
DU TK3530-SSV 5 3 Viton® Single Seal 1.4 145 $ 2317.00 DU PSE303-73 3x3 Straight 1.0 SG 300 7.5 HP, 3 PH 250 2370.00
DU TK3510-SSV 5 1 Viton® Single Seal 1.4 145 2387.00 DU PSE303-73A 3x3 Straight 1.4 SG 250 7.5 HP, 3 PH 250 2370.00
DU TK3530-SSE 5 3 EPDM Single Seal 1.4 145 2235.00 DU PSE303-103 3x3 Straight 1.0 SG 350 10 HP, 3 PH 270 2835.00
DU TK3510-SSE 5 1 EPDM Single Seal 1.4 145 2325.00 DU PSE303-153 3x3 Straight 1.4 SG 350 15 HP, 3 PH 300 3225.00
DU PSE403-153 4x3 HB Straight 1.4 SG 350 15 HP, 3 PH 300 3225.00
DU TK3530-SSW 5 3 * Viton® Double Seal 1.4 145 2672.00
DU SCPS3002 3x3 Self Prime 1.4 SG 350 15 HP, 3 PH 350 3601.00
DU TK3510-SSW 5 1 * Viton® Double Seal 1.4 145 2817.00 Note: Water=1.0 S.G.(Specific Gravity)=8.33 lbs. 1.4 S.G.= 12 lb. Material
* Viton® Double Seal with liquid reservoir.
D
Model No. PERFORMANCE DATA RKLD
PSI 5 9 14 18 20
Many Other 4295-98 GPM 40 35 25 15 5 Model
Models Available! PSI 5 9 14 23 29 GPM Wt.
4298-98 GPM 63 57 47 30 10 Part No. @ 20 PSI Lbs. Net Ea.
SC PSD303 3x3FPT Pump Unit with Pressure Seal 365 90 $ 1519.00
Max. Spec. Wt. SC PSD403HB 4x3HB Pump Unit with Pressure Seal 365 95 1519.00
Part No. Gravity Motor Lbs. Net Ea. SC RKLD300V 3x3FPT Pump Unit Less Pressure Seal 365 68 997.00
GR 4295-98 1.6 1/2 HP, 1 PH 38 $ 577.00 SC RKLD400V 4x3HB Pump Unit Less Pressure Seal 365 68 1065.00
GR 4298-98 1.6 1-1/2 HP, 1 PH 45 648.00 SC 118-000-236 Pressure Tube Assembly for Double Seal Pumps 509.00
GR 429J-98 1.6 1-1/2 HP, 3 PH 45 654.00
GR 429F-98 1.6 1/2 HP, 3 PH 35 575.00
Chemflo Close-Coupled Stainless
Centrifugal Pumps
Self Priming Centrifugals For Severe Duty Service
Close Coupled “CHEMFLO” Pumps are designed for severe service use. The 316SS investment
FEATURES: casting is more corrosion-resistant than 304 and much stronger than stamped/
• Stainless Steel FPT Ports formed stainless pumps. 56C C-Face 3600 RPM motor. These pumps have Viton®
mechanical seals and stainless fasteners. Nine sizes are available to 450 GPM
• TEFC Motors and 225’ head. Call for compatibility check with your liquid products.
• FPT Ports
• Viton® Mechanical FEATURES:
Seals D
• 316 Stainless Steel
• For Water Use or End Suction Centrifugals
Other Light Liquids
Flow @ *Max.
D
• Viton® Mechanical Seals
Part No. Pressure Shown *Motor Inlet x Outlet S.G. Wt. Net Ea. are Standard
EA JEU8067T1C 18 gpm @ 25 psi 1 HP, 1 PH 1-1/4" x 1" FPT 1.0 36 lbs. $ 497.50
EA JEU8067T3C 18 gpm @ 25 psi 1 HP, 3 PH 1-1/4" x 1" FPT 1.0 30 lbs. 433.50
EA JEU1506T1C 18 gpm @ 45 psi 2 HP, 1 PH 1-1/4" x 1" FPT 1.0 50 lbs. 508.00
Part No. Net Ea.
EA JEU1506T3C 18 gpm @ 45 psi 2 HP, 3 PH 1-1/4" x 1" FPT 1.0 46 lbs. 503.00
MX MP400 *Chemflo Pump with 5 HP, 3-Phase,
*1-phase motors are 115/230 volt, 3-phase are 208/230/460 volt.
TEFC Motor. 2” x 1-1/2”............................. $ 1736.64
For water @ 1.0 S.G; not for heavy or viscous liquids.
* 125 GPM@60’ head, up to 1.5s.g. liquids.
Viton® is a registered trademark of DuPont Performance Elastomers
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0222
Engine Drive & ANSI Centrifugal Pumps 103
Straight Self-Priming
Centrifugal Centrifugal
Large cavity
to handle
even
These pumps are from Pacer &
catastrophic Banjo and use the Briggs Intek
seal failure. engines and are equipped with a
large cavity “spacer” to separate the
engine and pump. The separator
Oversized
slinger to includes an oversized slinger & large
prevent any weep holes to prevent fluid from
liquid from entering the engine due to a seal
contacting failure. 2" Pumps flow 200-230 GPM.
engine.
Extra large weep holes.
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0229
104 Self-Priming Poly Centrifugal Pumps
Thermoplastic Pumps Polyester Transfer Pumps (Motor Drive)
Fertilizer transfer units, with PACER glass-filled polyester centrifugal pumps, have a Lovejoy
Use of tough engineering thermoplastic makes this a desirable pump for
shaft coupling with safety shield between the motor and pump shaft. EPDM mechanical seals.
pumping liquid products. The pump “castings” are made of thermoplastic Units with TEFC, 3450-RPM, one or three phase motors in 2, 3, 5 and 7-1/2 HP are available.
polyester which is noted for its outstanding chemical resistance. EPDM Do not pump substances which have pH factor of over 10 or a temperature of over 200° F.
mechanical seals are standard. Viton® also available. The PERFORMANCE CHART is based on water. NOTE: DO NOT USE STANDARD 3 HP SIZE
FOR LIQUIDS HEAVIER THAN WATER - USE 30010-E.
HEAD (in feet) 10 20 30 40 50 60
Self-Priming Poly Centrifugal Pumps 2 to PRESSURE (PSI)
SIZE HP
4.3 8.7 13.0 17.3 21.7 26.0
1-1/2" • 2" • 3" • Engine & Hydraulic Drive 7-1/2-HP 2" 2 GPM 120 100 80 60 50 25
Self-Priming 2" 3 GPM 175 160 155 140 125 100
2" 5 GPM 175 165 150 135 125 100
FEATURES: Lightweight corrosion- * 2" 5 GPM 240 230 215 190 155 115
resistant thermoplastic polyester 3" 7-1/2 GPM 275 275 250 220 180 150
*H igh flow units.
construction resists corrosion by water.
FAST PRIMING - Will lift 25 feet in less NOTE: 3" Units
D than one minute. HIGH CAPACITY - not available with
1-1/2" size will pump 100 GPM; 2" size the carrying handle.
will pump 150 GPM and 3" size will
pump 200 GPM.
HIGH CAPACITY - PROTECTED SEAL PROTECTED SEAL - Pump out vanes D
DURABLE - MADE OF PARTS on back of impeller reduces pressure and
THAT WILL NOT RUST OR CORRODE eliminates dirt in the seal area.
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0232
Self-Priming Centrifugal Pumps 105
Max. Required
Max GPM @ Spec. Hydraulic Hydraulic Speed Wt.
Part No. GPM 20 PSI Gravity Ports Motor HP Flow (GPM) (RPM) Lbs. Net Ea.
TK 222PIHY 200 135 1.4 2" x 2" 12 6 - 10 3450 75 $ 931.00
TK M222PIHYW * 200 135 1.4 2” x 2” 12 6 - 10 3450 75 1115.00 D
TK M332PIHYW * 350 300 1.4 3” x 3” 21 9 - 13 3450 190 1548.00
* Manifold Pumps with Wet Seal.
222POI
Pump Only
222PBI
Pump Only
Pumps Only See Top for Construction & Seal Details
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0230
106 Self-Priming Centrifugal Pumps
Stainless Self-Priming
Centrifugal Transfer Pumps Poly “Double Wet Seal”
Self-Priming Centrifugal Transfer Pumps
Constructed of 316 stainless steel for
excellent chemical resistance and durability.
Self-priming design with check valve. Bolt-on
flanged ports for easy maintenance. Viton®
mechanical seals and gaskets. Available in These pumps include double EPDM
pedestal version for long coupling to electric (Viton® available) “wet” mechanical
motors or gas engines (run at 3450 RPM), seals contained in a glycol reservoir.
“Pump-Packs” for close coupling to gas Pump is separated from engine
Engine and includes large weep holes to
Mount D engines and complete with gas engines (also
available in C-Face design for close-coupling further protect engine. “V” shaped
Version
Shown to electric motors). volute and inlet check valve for quick D
priming. Pump bodies constructed
of glass-filled polypropylene for
Max. GPM excellent chemical resistance.
Part No. Description Ports Shaft GPM @20 PSI Wt. Net Ea.
TK 200PBSS 2” 316SS Pedestal Pump..... 2" 3/4" 190 115 55 lbs. $ 1327.00 Max. GPM
TK 300PBSS 3” 316SS Pedestal Pump..... 3” 3/4” 340 215 100 lbs. 2491.00 Part No. Description Ports GPM @20 PSI Wt. Net Ea.
TK 300PH13SS 3” 316SS Pump with 13 HP TK 300P11PROW 3” Poly Double Seal Pump with
Honda Engine....................... 3” - 340 215 150 lbs. 4885.00 11 HP Briggs Pro Engine 3” 293 176 150 lbs. $ 814.00
TK 200PO-SS 2” 316SS Pump-Pack*........ 2” 3/4” Key 190 115 55 lbs. 1270.00 TK 300PH13W 3” Poly Double Seal Pump with
TK 300PO-SS 3” 316SS Pump-Pack*........ 3” 1” Key 340 215 55 lbs. 2441.00 13 HP Honda Engine, 12 Volt Start 3” 293 176 160 lbs. 1251.00
* Pump-Packs for close coupling direct to engines - Verify shaft with engine shaft. For 2” pumps, use TK 300PBW 3” Poly Double Seal Pump with
3 HP for water and 5 HP for heavier liquids like fertilizer; for 3” pumps, use 8 HP for water and 11 1” Shaft & Pedestal for Motor 3” 293 176 25 lbs. 581.00
HP or 13 HP for heavier liquieds.
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0776
Centrifugal Transfer Pumps 107
• Pedestal Pump
• Pump Kit for Bolting to a Gas Engine Hydraulic
• Kit for Bolting to AC Motor Also Available Drive Pump
• Engines are EPA Certified. Not for use in California
• Flow Rates Up to 330 GPM; Pressures to 60 PSI
• Viton® Mechanical Seal D
• One-Year Hypro Warranty on All Pump & PowerPro™ Engines Pedestal Pump
• Pump & Engine Repair Parts Available
• Base Plates also Available.
• EPDM Seals
D
• MPT Thread Connections -
Poly Hose Barbs, Flynuts &
Strainers Also Included
• 2” 5.5 HP or 3” 6.5 HP
13808 Industrial Road 601 West 76th St. GPM @ GPM @ GPM @ GPM @ GPM @ GPM @ GPM @
Omaha, NE 68137 Davenport, IA 52806 PART NO. 10 PSI 15 PSI 20 PSI 25 PSI 30 PSI 35 PSI 40 PSI
1-800-228-9666 • 1-402-333-1444 1-800-553-6975 • 1-563-386-0930 HY 1542A-SP 144 136 124 110 94 78 57
FAX: 1-402-333-5546 FAX: 1-563-386-5448 HY 1543A-SP 251 233 213 190 162 135 99
e-mail: dultmeier@dultmeier.com
Part No. Description Wt. Net Ea.
website: dultmeier.com HY 1542A-SP 2” Aluminum Pump with 5.5 HP PowerPro Engine 55 lbs. $ 235.50
HY 1543A-SP 3” Aluminum Pump with 6.5 HP PowerPro Engine 66 lbs. 276.50
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0759
108 Scot Centrifugal Transfer Pumps
Straight Centrifugal Long-Coupled Scot C.I. Centrifugal Pumps
C.I. Pedestal Pumps Straight & Self-Priming
Double sealed bearings •
Viton® mechanical seals
2” & 3” Sizes • stainless shaft sleeves •
All iron construction • base
Excellent pumps for fertilizer, agchemical, mounted • Long-coupled
with Lovejoy coupling drives
diesel fuel and many other liquids. Direct • TEFC motors. D
couple or belt drive these pumps to electric
motors and gas engines (run at 3500
RPM). All iron construction, stainless shaft Model SC7533
sleeves and viton® mechanical seals. Self-Priming
SC LFE215R100P2 3"x3" 1.0 400 10 3 160 1677.00 2" Ports PUMPING CLEAR LIQUID 1.0 SPECIFIC GRAVITY
Close-Coupled
Self-Priming
Pump Units D
FPS575
Cast Iron with TEFC 3" Ports U.S. GALLONS PER MINUTE PUMPING
D Motor Drive CLEAR LIQUID 1.0 SPECIFIC GRAVITY
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0227
Scot Centrifugal Transfer Pumps 109
56
MTRS PSI FEET NUMBER 40.000.529 SPEED 70˚F PUMP SIZE: 3.0 X 3.0 X 6.5
IMP. TYPE: ENCLOSED
MAX. DIA.: 6.50
4x3 & 3x3 Flanged and FPT Pump Units for Plant Use
IMPELLER NO.: C1159
MAX. SPHERE: 1/2
MAX HP FOR
95
NUMBER 40.000.321 70˚F
FEATURES: 6” x 4" and 6” x 5" Flanged Ports • All Iron Construction • Cast Bearing Frame • Double 25.0 10.25
Sealed Ball Bearings • Stainless Sleeves • Viton® Seal (severe duty seals available) • 1-3/8" Shaft •
10.25 Impeller • 1750 RPM.
FP95
U.S GALLONS
PER MINUTE
CUBIC METERS
PER HOUR
96
MTRS PSI FEET NUMBER 40.000.322 70˚F PUMP SIZE: 6.0 X 5.0 X 10.0
D 60 Hz IMP. TYPE:
MAX. DIA.:
ENCLOSED
10.25
D IMPELLER NO.: 96
MAX. SPHERE: 1-1/4
STD. IMPELLERS
FOR ODP MOTORS
H.P. DIA.
15.0 8.50
FP 96 20.0 8.90
25.0 9.38
30.0 10.25
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0223
110 Centrifugal Transfer Pumps
All iron centrifugal pumps from Goulds for transfer of a wide variety of Liquid Solutions. High capacity pumps in
4" x 3" or 6" x 4" sizes with Silicon Carbide/Viton® Mechanical Seals are an ideal choice for fertilizer and chemical transfer.
Standard Features Include: Back Pull-Out Design to reduce maintenance down time. • Silicon Carbide/Viton® Mechanical Seals for added
durability and corrosion resistance. • Replaceable Wear Components including 316SS stainless steel shaft sleeve, casing and hub wear rings. •
Enclosed Impeller design with dynamic balancing. • 125# ANSI Flanges on suction and discharge for piping versatility. • 4 x 3 sizes will pass up to
3/8" solids, 6 x 4 sizes will pass up to 7/16" solids. • Shaft size is 1-5/8" on all models. • Grease lube bearings. • All pumps are rated to 1750 rpm
for longer seal and bearing life and improved performance on longer suction piping. All iron construction. 212° F. maximum temperature.
PUMPS ONLY - Run at 1750 RPM
Part No. Flanged Ports Flow @ 25PSI Impeller Wt. Net Ea.
GL 12AIFRMD4 4 x 3 440 GPM 8-5/8" 180 Lbs. $ 1995.00
GL 12AIFRMC4 4 x 3 500 GPM 9” 180 Lbs. 1995.00
GL 12AIFRMA4 4 x 3 630 GPM 10-1/16" 180 Lbs. 1995.00
GL 14AIFRME4 4 x 3 770 GPM 11-3/4" 255 Lbs. 2520.00
GL 14AIFRMC4 4 x 3 840 GPM 12-5/16" 255 Lbs. 2444.00
GL 15AIFRMK4 6 x 4 820 GPM 9-7/8" 235 Lbs. 2735.00 D
GL 15AIFRMJ4 6 x 4 900 GPM 10-1/4" 235 Lbs. 2735.00
GL 15AIFRMF4 6 x 4 1100 GPM 11-1/16" 235 Lbs. 2781.00
GL 15AIFRMD4 6 x 4 1230 GPM 11-7/8" 235 Lbs. 2781.00
GL 10K45 Replacement Seal Cartridge for all above pumps............. 172.00
GL 5K74 Buna Casing O-Ring for 12AI Pumps................................ 11.05
GL 5K199 Buna Casing O-Ring for 14 & 15AI Pumps....................... 11.55
PUMP/MOTOR Units (4" x 3") - 1750 RPM
Goulds Pump/Motor Units feature the frame mounted Goulds Pumps Max.
Flanged Specific Flow @ Max. *Motor Wt.
shown below mounted with S-Flex coupling assemblies and 3-phase
Part No. Ports Gravity 25PSI Flow 3PH Lbs. Net Ea.
TEFC motors. All units are assembled and properly aligned prior to DU GL12D-10 4 x 3 1.0 440 GPM 630 GPM 10 HP 535 $ 3470.00
shipping. SAE mounts and close-coupled versions also available. DU GL12D-15 4 x 3 1.4 500 GPM 670 GPM 15 HP 660 3935.00
DU GL12A-15 4 x 3 1.0 630 GPM 730 GPM 15 HP 660 3908.00
DU GL12A-20 4 x 3 1.4 630 GPM 730 GPM 20 HP 700 4271.00
DU GL14E-25 4 x 3 1.0 770 GPM 810 GPM 25 HP 800 5198.00
DU GL14E-25A 4 x 3 1.4 680 GPM 775 GPM 25 HP 800 5229.00
DU GL14C-30 4 x 3 1.0 840 GPM 855 GPM 30 HP 850 5431.00
DU GL14E-30 4 x 3 1.4 770 GPM 810 GPM 30 HP 850 5493.00
DU GL14C-40 4 x 3 1.4 840 GPM 855 GPM 40 HP 950 6225.00
*U se pumps with 1.4 S.G. for heavy or viscous products such as fertilizers, brines, etc.
Crane Deming Centrifugal Pump Units Crane Deming Double Seal Pump
These 4021 Series Standard Duty Pumps will handle a wide range of fluids. Standard
construction is all iron, 10" impellers, double Viton® mechanical seal with Bowen
grease lubricators. Pumps are base mounted to a 52" x 18" baseplate with Lovejoy
S-Flex coupling drives. Motors are 1750 rpm/TEFC/3-Phase.These units have flanged
CRANE ®
Same 4021 Standard Duty
DEMING PUMPS
® Pumps used in pump units
connections and designed to provide years of trouble-free service. Stainless impellers
are available at additional cost. Maximum liquid temperature is 225° F. shown at left. All iron, 1-1/4”
S.S. shafts, Viton® double
mechanical seals with
CRANE ®
Bowen grease lubricators.
DEMING PUMPS
®
D
For fertilizer and other heavy liquids,
Part No. Pump Style Wt. Net Ea.
use pumps shown with S.G. of 1.33 or
higher. (1.0 S.G. for water only).
Run at 1750 RPM PW 3M 4” x 3” Flanged 145 lbs. $ 3279.00
GPM PW 4M 5” x 4” Flanged 225 lbs. 3657.00
Max. Max. Wt. PW 5M 6” x 5” Flanged 225 lbs. 3877.00
Part No. Pump Unit Size HP Flow S.G. Lbs. Net Ea. PW 6M 6” x 6” Flanged 275 lbs. 4515.00
DU CD3M-15 3M Deming 4X3 15 620 1.0 585 $ 4991.00 PW 118930 Double Viton® Seal.... 364.50
DU CD3M-20 3M Deming 4X3 20 620 1.33 635 5350.00 PW 0030899 Double Buna Seal...... 136.00
DU CD4M-20 4M Deming 5X4 20 900 1.0 665 5855.00
DU CD4M-25 4M Deming 5X4 25 900 1.33 715 6093.00
PW 0004474 Suction Cover Gasket. 11.40
DU CD4M-30 4M Deming 5X4 30 900 1.6 780 6488.00 SC 118-000-236 Pressure Seal Assembly. 509.00
DU CD5M-25 5M Deming 6X5 25 1300 1.0 765 6221.00 PW 0004159 Bowen Lubricator....... 62.80
DU CD5M-30 5M Deming 6X5 30 1300 1.33 805 6716.00
DU CD5M-40 5M Deming 6X5 40 1300 1.6 845 7366.00
DU CD6M-30 6M Deming 6X6 30 1600 1.2 820 7296.00
DU CD6M-40 6M Deming 6X6 40 1700 1.5 1020 7956.00 Viton® is a registered trademark of DuPont Performance Elastomers
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0224
Stainless Centrifugal Transfer Pumps 111
Standard Features Include: Precision Investment Cast 316 Stainless liquid end components (Casing, Impeller, Seal Housing, Shaft Sleeve).
• Rugged Cast Iron bearing frames and adapters. • Back Pullout Design for quick maintenance. • Open Impeller Design pass 3/8” solids. •
Viton® Mechanical Seals (carbon, ceramic, Viton®). • Rugged TEFC Motors, continuous duty (3500 RPM; Explosion-proof motors available). •
Some units sized for Heavier Chemicals. (See S.G. rating below). Many Models Available!
D
4SS
Pedestal Model
1SS
Close-Coupled Model D
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0870
112 Stainless Steel Centrifugal Pumps
Pro-Steel Stainless Steel Centrifugal Pumps from Ebara are rated for dependable, continuous duty performance. Built for the most demanding of liquid
transfer applications. Available in Straight Centrifugal, Self-Priming and High Pressure 2-Stage models. All pumps are “bulge formed” through a state-of-the-art
manufacturing technique that increases pump efficiency, part integrity, reliability and longevity.
Standard Features Include: • Close-Coupled Design to save space • High Quality Stainless components and ceramic/Viton® seals for added corrosion
resistance • Back Pullout Design allows for repairs without removing pumps from system • Mounting Versatility allows for horizontal or vertical service •
Centerline Discharge and foot support under casing ensure maximum resistance to misalignment • Available with Flanged or FPT ports • Rated to 212° F.
with standard ceramic/Viton® seals. (250° F. seals also available for single stage pumps). • Motors are single or three phase TEFC. (Explosion-proof or ODP
also available).
† Note: Flows are based on liquids with 1.0 specific gravity (water). For liquids other than water contact us for HP and chemical compatibility check.
Flanged Ports
† Max.
Specific
Part No. Max. Flow *Motor Inlet x Outlet Gravity Wt. Net Ea.
EA 32-125T1 **80 gpm @ 30 psi 3 hp, 1 ph 2" x 1-1/4" Flanges 1.0 97 lbs. $ 1209.00
EA 32-125T3 80 gpm @ 30 psi 3 hp, 3 ph 2" x 1-1/4" Flanges 1.0 79 lbs. 926.00
EA 40-125B1 ••200 gpm @ 30 psi 5 hp, 1 ph 2-1/2" x 1-1/2" Flanges 1.0 109 lbs. 1150.00
EA 40-125B3 200 gpm @ 30 psi 5 hp, 3 ph 2-1/2" x 1-1/2" Flanges 1.0 99 lbs. 1123.00 D
EA 50-160T1 ••380 gpm @ 30 psi 10 hp, 1 ph 2-1/2" x 2" Flanges 1.0 185 lbs. 1883.00
EA 50-160T3 380 gpm @ 30 psi 10 hp, 3 ph 2-1/2" x 2" Flanges 1.0 165 lbs. 1498.00
230-Volt Only. Open Drip-Proof. 1-phase motors are 115/230 volt, 3-phase are 208/230/460 volt.
† Designed for 150 lb. ANSI Flanges, (Not included). ** 230-Volt Only. Open Drip-Proof
• ODP Motor with EPDM Seal. •• ODP Motor with VITON® Seal.
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0225
Multi-Stage Centrifugal Pumps 113
Poly Transfer
Pumps
Self-Priming
D
Centrifugal Pumps
Motor *Flow Wt.
Ideal for fertilizer Part No. (TEFC) Rate Ports Lbs. Net Ea.
and chemical GL 1SVA1F4EO 1-1/2hp, 1ph 10 GPM @ 90 psi 1" NPT 70 $ 1070.00
transfer GL 1SVA1G4FO 2hp, 1ph 15 GPM @ 90 psi 1" NPT 80 1154.00
GL 1SVA1H4LO 3hp, 1ph 12 GPM @ 180 psi 1" NPT 110 1663.00
• Polypropylene Housing GL 1SVA1H5LO 3hp, 3ph 12 GPM @ 180 psi 1" NPT 110 1250.00
Gas Engine is Suitable for corrosive GL 1SVB1J4QO 5hp, 1ph 15 GPM @ 215 psi 1-1/4" Flange 125 2253.00
Model 1543P environments. GL 1SVB1J5QO 5hp, 3ph 15 GPM @ 215 psi 1-1/4" Flange 125 1516.00
GL 2SVB1J4QO 5hp, 1ph 20 GPM @ 225 psi 1-1/4" Flange 125 2672.00
• PowerPro Engine with
GL 5SV17FG4F20 5hp, 3ph 20 GPM @ 225 psi 1-1/4" Flange 125 1613.00
Overhead Valve; Low
GL 3SVA1K5HO 7-1/2hp, 3ph 40 GPM @ 190 psi 1-1/2" NPT 135 2520.00
Oil Sensor, Recoil.
GL 3SVB1L5LO 10hp, 3ph 60 GPM @ 210 psi 2" Flange 200 3093.00
• Self-Priming to 25 Feet EV R114S Flange — 1-1/4" FPT , 300#, 304SS . ....................... 39.75
Pedestal Lift. EPDM Seal EV R112S Flange — 1-1/2" FPT, 300#, 304SS ........................... 62.55
Model 9243-SP EV R200S Flange — 2" FPT, 300#, 304SS . ............................... 60.95
D
Note: 300 lb. Flange Gaskets Also Available.
0 10 30 40 50 58
GPM
PSI
200 182 162 136 106
0 10 20 30 40
65
50
0
60 SERVICE & REPAIRS
GPM 200 184 164 141 114 80 0
PSI 0 10 20 30 40 50 54
Hydraulic Did you know? We can
Model 9343P
GPM
* @11 GM Oil Flow for 9342P.
440 400 330 270 185 70 0
service almost every
Part No. Description Wt. Net Ea. brand of pump we sell
HY 1542P-5SP 2” Poly Pump with 6.5 HP PowerPro. 58 lbs. $ 282.50
HY 9342P-HM5CSP 2” Poly Pump w/Hydraulic Drive........ 27 lbs. 494.50 in our catalog.
HY 1543P-130ESP 3” Poly Pump w/13 HP PowerPro, 12 Volt. - 751.00
DU 1543P-13HN
HY 9243P-SP
3” Poly Pump w/13 HP Honda 12 Volt -
3” Poly Pedestal Pump....................... -
1088.00
414.50
Call us at 1-800-228-9666
HY 9343P-GM6-SP 3” Poly Pump w/Hydraulic Drive........ - 774.00 (Omaha, NE) for a quote!
HY 3430-0692 3” Polypropylene Pump Kit *............. - 252.00
HY 3430-0635 EPDM Seal Kit.................................... - 30.50
HY 3430-0659 Viton® Seal Kit ................................. - 133.00
HY 3430-0757 3” EPDM Seal Kit .............................. - 144.50 Viton® is a registered trademark of DuPont Performance Elastomers
* For Installation on 13 HP Briggs or Honda Engines
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0794
114 Self-Priming Centrifugal Transfer Pumps
Excellent pumps for refined fuels including gasoline, diesel, kerosene and other petroleum
products. Also great for water. 3” Pumps are constructed of aluminum casings, Almag 35 or
aluminum impellers, copper alloy replaceable wear rings and cast iron pedestals. Oil lubricated
bearings and bolt-on FPT ports. 2” Pump is constructed with cast iron casing, copper alloy
impeller and iron replaceable wear ring.
D All pumps have Viton® mechanical seals. 2” Pump will pass 3/8” solids; 3” pumps will pass
7/16” solids and 4” pumps will pass 1/2” solids. Use with explosion-proof motors for gasoline
and other flammable liquids. Not for fertilizer.
“O” Series
Self-Priming Pumps
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0871
GORMAN-RUPP Centrifugal Transfer Pumps 115
Petroleum DU GR4X3R-20T
DU GR6X5RP-30
DU GR6X5RP-50
*700
1400
1475
700
1400
1475
4” x 3”
6” X 5”
6” x 5”
20
30
50
750
1200
1200
9978.00
14850.00
16599.00
Pumps * Includes Teflon Seal for pumping Ethanol.
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0226
116 GORMAN-RUPP Centrifugal Trash Pumps
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0231
High Pressure Centrifugal & Sludge Pumps 117
D
designed for lawn sprinkling,
a g r i c u l t u r a l s p r ay i n g ,
Air Drive Trash Pump
dewatering, fire fighting,
emergency water supply and Air Driven “Sludgemaster” Trash Pump from
pressure boosting. Wheel Warren Rupp. This submersible, air-powered
2P5XHR
2” High Pressure - 1 Stage Kits available. pump is ideal for transfer of trash-laden water with
mud, leaves, sand, sludge and soft solids to 1-1/2".
Model No. PERFORMANCE DATA Maximum flow to 300 GPM. Sturdy aluminum hous-
4787-95
PSI 25 45 65 75 85 - - - ing and ductile impeller for rough handling and long
GPM 65 50 33 21 8 - - -
life. Discharge port is 3" FPT. Fits through a 14"
PSI 25 45 65 75 85 - - -
4789-95 GPM 65 50 33 21 8 - - - diameter opening. Optional rock screen available.
PSI 25 45 65 75 85 100 130 135
5830-96
GPM 65 65 57 52 47 41 20 14
PSI 25 45 65 75 85 100 130 135
5831-96 Model SMA3A
GPM 65 65 57 52 47 41 20 14
3" Sludgemaster
PSI 25 45 65 75 85 95 - - PERFORMANCE CURVE
2P5XAR GPM 120 96 70 60 48 25 - -
Note: This performance based on water
PSI 25 45 65 75 85 - - -
2P5XHR
GPM 108 80 55 35 14 - - -
Total Head
D
1-1/2” High Pressure Pump (2 Stage) Tank Wt.
Part No.
HP Engine Material Size Run Time Lbs. Net Ea.
GR 4787-95
5.5 B&S Intek Pro Cast Iron 3 Quarts 100 min. 104 $ 708.00
GR 4789-95
6.5 Honda Cast Iron 3.8 Quarts 100 min. 99 901.00
2” High Pressure Pump (2 Stage) Tank Wt.
Part No.
HP Engine Material Size Run Time Lbs. Net Ea.
GR 5830-96
6.5 B&S Intek Pro Cast Iron 3 Quarts 100 min. 70 $ 916.00 Capacity in U.S. Gallons per minute
GR 4789-95
5.5 Honda Cast Iron 3.8 Quarts 100 min. 66 901.00
2” High Pressure Pump (1 Stage) Tank Wt.
Part No. HP Engine Material Size Run Time Lbs. Net Ea. Part No. Wt. Net Ea.
GR 2P5XAR 5.0 B&S CP650 Aluminum 3 Quarts 120 min. 90 $ 679.00 SO SMA3A Air Drive Trash Pump. 71 lbs. $ 1949.47
GR 2P5XHR 5.0 Honda Aluminum 3.8 Quarts 100 min. 86 880.00
Viton® is a registered trademark of DuPont Performance Elastomers
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0725
118 ACE Centrifugal Sprayer Pumps
PTO Drive Centrifugal Sprayer Pumps Hydraulic Motor Drive
• Easily replaced Viton® mechanical seal Centrifugal Sprayer Pumps
• ABS Plastic Belt & Shaft Guard
• Spring loaded Idler to maintain Standard &
proper belt tension High
• Cast Iron construction Performance
Models
• Sealed ball bearing
• 10-groove poly V-Belt
Power
Take-Off
Mounted Flanged
D FPT D
Ports
Ports
These cast iron straight centrifugal frame mounted pumps are driven by a
D close coupled hydraulic motor. The hydraulic motors have built in reverse
check valves to prevent seal damage due to impeller coasting and reverse
rotation. Each motor also has an integral needle valve to by-pass excess
D
hydraulic fluid on open center systems. Valox Impeller; Cast Iron optional.
Stainless shafts and wear rings. Standard Viton® mechanical seals. Note:
PTO RPM PRESSURE CAPACITY HP
For severe duty seal (silicon carbide) add suffix “A” to pump number shown.
STANDARD PUMPS 600 60 PSI 20 GPM 1200 GPH 1-1/4
or 40 PSI 50 GPM 3000 GPH 2
1-1/4" inlet x 1" 1000 30 PSI 60 GPM 3600 GPH 2-1/4
discharge PUMP NO. & MAX. Press. HYD.
* Data based on 1 foot lift through unrestricted
suction hose and fittings with full 1-1/4" I.D. PORT SIZE & MAX. GPM MOTOR Can be Used on Hydraulic Systems:
150 SERIES PERFORMANCE CHART FMC-HYD-202 70 GPM 2 GPM Turf & Golf Course Units with LS
HIGH TRACTOR 450 500 540 600
1-1/4" x 1" 100 PSI @ 4600 RPM Closed and Open Centered Systems
PERFORMANCE PTO SPEED RPM RPM RPM RPM FMC-HYD-203 80 GPM 3 GPM rated at 2-11 GPM
PSI GPM GPM GPM GPM
150 SERIES Pressure Compensating Closed Center
20 70 80 95 100
1-1/2" X 1-1/4" 30 55 75 90 100 FMC-HYD-204 100 PSI @ 4600 RPM 4 GPM (John Deere), or Open Centered Systems
40 40 65 85 95
100 PSI - 40 GPM at 600 RPM 50 25 55 80 90 1-1/4" x 1" FPT 60 GPM rated at 4-13 GPM
Due to Increased pulley ratio 60 10 45 70 80
70 - 25 65 75 FMC-HYD-210 100 PSI @ 4600 RPM 10 GPM Load Sensing Closed Center Systems
and 1-1/2" inlet x 1-1/4" 80 - 10 55 65 1-1/4" x 1" FPT 60 GPM (Case-IH type) or Open Centered Systems
90 - - 30 55
Discharge ports 100 - - - 40 rated at 10-17 GPM
Part No. Standard Pumps Net Ea. FMC-HYD-310 60 PSI @ 3950 RPM 16 GPM Open Center Systems Rated at 16-24 GPM
AC PTOC600-10QC Direct Mount on 1-3/8" 600 RPM PTO Shaft. 1-1/4" x 1" FPT 60 GPM
6-Spline Quick Coupler PTO Drive Shaft. Wt. 46 lbs.. $ 580.00 FMC150HYD206 120 PSI @ 5100 RPM 7 GPM Pressure Compensating Closed Center
AC PTOC1000-10 Direct Mount on 1-3/8" 1000 RPM PTO Shaft. 1-1/2" x 1-1/4" FPT 120 GPM Systems (John Deere type), Load Sensing
21-Spline split PTO shaft & Split ring Locking FMC150FHYD206:
Closed Center Systems (Case-IH type),
Collar. Wt. 43 lbs.................................................... 583.00
Inlet: 220 FP Flange / 1-1/2” FPT
and Open Center systems rated 7-16 GPM
AC PTOC1000-175 Direct Mount on 1-3/4" 1000 RPM PTO Shaft.
20-Spline Split PTO drive shaft & Split ring
Outlet: SP Flange / 1-1/4” FPT
200 Equipped with restrictor orifice.
Locking Collar. Wt. 45 lbs...................................... 608.00 FMC150HYD206A Same as FMC150HYD206 with Silicon Carbide Seal
Part No. High Performance Pumps Net Ea. FMC200HYD210 80 PSI @ 3950 RPM 10 GPM Pressure Compensating Closed Center
AC PTOC150-6SPQC Direct Mount on 1-3/8" 600 RPM PTO Shaft. 2" x 1-1/2" 180 GPM Systems (John Deere type), Load Sensing
Equipped with Quick Coupler. Wt. 51 lbs............... $ 654.00 Closed Center Systems (Case-IH type),
AC PTOC150-21SP Direct Mount on 1-3/8" 1000 RPM PTO Shaft. and Open Center systems rated 10-17 GPM.
21-Spline PTO Shaft & Locking Collar. Wt. 48 lbs.. 668.00 Equipped with restrictor Orifice.
AC PTOC150-20SP Direct Mount on 1-3/4" 1000 RPM PTO Shaft.
20-Spline PTO drive shaft & Locking Collar. Wt. 50 lbs.. 682.00 FMC200HYD304 120 PSI @ 5100 RPM 11 GPM Pressure Compensating Closed Center
AC PTOC150-600B 1" Dia. Stub Shaft & integral Mounting Base for 2" x 1-1/2" FPT 200 GPM Systems, Load Sensing Closed Center
600 RPM Tumblerod Drive Shaft. Wt. 52 lbs......... 660.00 FMC200HYD304S Same as FMC200HYD304 but Stainless Systems, & Open Center Systems rated at
AC PTOC150-1000B 1" Dia. Stub Shaft & Integral Mounting Base for 11-20 GPM. Equipped with restrictor orifice.
1000 RPM Tumblerod Drive Shaft. Wt. 45 lbs....... 660.00
FMC200FHYD304: Inlet: 3” SP Flange. Outlet: 220 FP Flange
Part No. Repair Pumps/Kits for Above Pumps Net Ea.
AC R600 Repair Kit Includes seal, two o-rings, bearings, snap rings, &
slinger. For PTO and hydraulic std.& high press. series Ace Pumps.. $ 42.60 See Following Pages for Hydraulic Oil Flow Limiting Valves
AC FMC-MIA Replacement Pump only, machined for
idler arm for PTOC Standard Units. Wt. 18 lbs............. 261.50 Centrifugal Pump - Hydraulic Motor Combination
AC FMC150MIA Replacement Pump Only, Wt. 18 lbs............................ 264.00 Part No. PORTS MOTOR WT. Net Ea.
ACE Pump Parts AC FMC-HYD-202
AC FMC-HYD-203
1-1/4" x 1"
1-1/4" x 1"
202
203
25 lbs. $ 553.00
25 lbs. 553.00
Part No. For Standard Pumps Net Ea. AC FMC-HYD-204 1-1/4" x 1" 204 26 lbs. 547.00
AC BAC-28-10 10-Groove Poly V-Belt For PTOC-600-10 Pump. $ 18.95
AC FMC-HYD-210 1-1/4" x 1" 210 27 lbs. 544.00
AC BAC-28-10M 10-Groove Poly V-Belt For PTOC-1000-10 Pump 17.45
AC BAC28-10M150 10-Groove Belt. For PTOC-15-1000 Pump......... 18.80 AC FMC-HYD-310 1-1/4" x 1" 310 33 lbs. 575.00
AC BAC28-10150 10-Groove Belt. For PTOC-150-600 Pump......... 20.20 AC FMC150HYD206 1-1/2" x 1-1/4" 206 31 lbs. 561.00
AC BAC-28-8 *8-Groove Poly V-Belt For PTOC-600 Pump...... 15.40 AC FMC150HYD206A †1-1/2" x 1-1/4" 206 31 lbs. 606.00
AC BAC-28-8M *8-Groove Poly V-Belt.For PTOC-1000 Pump.... 14.70 AC FMC150FHYD206 FPT & Flanged 206 31 lbs. 586.00
AC BAC-7V Carbon-Ceramic Viton® Seal............................. 23.50 AC FMC150FSHYD *FPT & Flanged 206 31 lbs. 921.00
AC BAC-4 Gasket (Not in R600).......................................... 1.80 AC FMC200HYD210 2" x 1-1/2" 210 33 lbs. 657.00
AC BAC-4-150 O-Ring - High Pressure Pumps.......................... 4.20 AC FMC200HYD304 2" x 1-1/2" 304 38 lbs. 661.00
AC BAC-7SC Silicon-Carbide Viton® Seal (Severe Duty)........ 84.00
AC FMC200HYD304S 2” x 1-1/2” 304 38 lbs. 899.00
AC BAC-8 “O” Ring for BAC-6SS......................................... .60
AC BAC-6SS 5/8" Driven Shaft. Left Hand Thread “SS” Steel.. 54.00 AC FMC200FHYD304 3” Flg. x 2” FP Flg. 304 38 lbs. 693.00
AC BAC-37 Sealed Ball Bearing. For BAC-6SS Driven Shaft 2.60 AC IHK86 Hydraulic Installation AC Kit . ........................ 510.00
AC BAC-5 Idler Torsion Spring............................................. 12.00 AC 41374 200 Series Hydraulic Motor Repair Kit - New 11/99 31.50
*8-Groove Poly V-Belts were used by ACE prior to their 1972 Models AC 41379 310 Hydraulic Motor Repair Kit . ........................ 16.35
which use the 10-Groove Poly V-Belt. * 316 Stainless Steel. **C.I. Impeller, E-coated. † With Silicon Carbide Seal.
Viton® is a registered trademark of DuPont Performance Elastomers
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0233
ACE Centrifugal Sprayer Pumps 119
Part No. Shaft FPT Ports Wt. Net Ea. Part No. Wt. Net Ea.
AC FMC-CW-150 Pump Only 5/8" 1-1/2" x 1-1/4" 20 lbs. $ 256.00 AC FMC-MIA 18 lbs. $ 261.50
AC FMC-CW-200 Pump Only 5/8" 2" x 1-1/2" 24 lbs. 333.00 AC FMC150MIA 23 lbs. 264.00
AC FMC-CW-800 Pump Only 7/8" 2" x 1-1/2" 42 lbs. 701.00 AC FMC200 24 lbs. 333.00
AC FMC200X 24 lbs. 362.00
* FMC200X is heavy duty version with 3/4" shaft.
Magnetic Clutch
Driven Pumps 12-Volt
Magnetic
Cast iron pedestal style pumps
with a double groove machined
Clutches
steel pulley and 12 Volt clutch.
Available in CW or CCW rotation
(when facing pulley side). Viton®
seal, Valox impeller. See above for
performance data. Silicon carbide The MAGNI-CLUTCH mounts directly to the pump,
seals and cast iron impeller D and is powered by a 12-volt D.C. Draws only 2 amps.
Units are supplied with adaptors for Ace “FMC” or MC12
available for heavy duty use. MAGNI-CLUTCH
Hypro 9200 Series pumps.
5-1/4 O.D. x 5/8" Bore
MCH2 Heavy Duty Clutch Features: Heavy duty bearing 10 HP @ 4000 RPM
Part No. Description Wt. Net Ea.
• Higher torque - 30 ft../lbs. • Transmits up to 23 HP @ 4000
AC FMC-CW150MAGD 1-1/2" x 1-1/4" CW Pump.......................... 25 lbs. $ 470.50
RPM • Single radial sealed ball bearing • 5/8” bore x 5” pulley.
AC FMCCW150MGDX3 1-1/2" x 1-1/4" HD CW Pump, 3/4" Shaft †... 25 lbs. 499.50
AC 47255 1-1/2" x 1-1/4" HD CW Pump with Pully Shaft Magnet Adapter
3/4" Shaft & Silicon Carbide Seal †........... 25 lbs. 547.00 SI-NO. Dia. Dia. Dia. Hub I.D. Application
AC FMC-CW200MAGD 2" x 1-1/2" CW Pump................................. 45 lbs. 577.00 MC12-AC 5" 5/8" 3.975" 1.812" Ace FMC
AC FMC-CW800MAGD 2" x 1-1/2" CW Pump................................. 45 lbs. 1210.00 MC12-HY 5" 5/8" 3.975" 2.075" Hypro 9200
AC FMC-150MAGD 1-1/2" x 1-1/4" CCW Pump *..................... 25 lbs. 470.50 MCH2 5" 5/8" 5.585" 2.075" Hypro 9200
AC FMC-200MAGD 2" x 1-1/2" CCW Pump *............................ 45 lbs. 577.00 Note: Adapter hub attaches to pump housing with set screws. Model MCH2
* Available in a flanged version IE FMCF *MCH2 has 5.585"Dia. Magnet for heavy duty 9200 applications Heavy Duty Clutch
† Special for Spray Coupe
Part No. 12-VOLT MAGNETIC - CLUTCHES Wt. Net Ea.
SI MC12-AC For ACE FMC Pump......................................... 4.5 lbs. $ 195.00
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0234
120 Centrifugal Sprayer & Clutch Drive Pumps
Part No. Description Net Ea. Part No. Connections Material Seal Rotation Wt. Net Ea.
AC FMC650HYD Cast Iron Centrifugal Pump. 1-1/2” x 1-1/4” FPT. HY 9263CC 1-1/4” x 1-1/2” FPT Cast Iron Viton® CCW 23 lbs. $ 471.00
14.5 GPM. Hydraulic Motor. Maximum Flow is HY 9263C-CU Flanged Cast Iron Viton® CCW 23 lbs. CALL
140 GPM. Maximum Pressure is 160 PSI. HY 9263CCR 1-1/4” x 1-1/2” FPT Cast Iron Viton® CW 23 lbs. 477.00
Single Mechanical Seal. Wt. 39 lbs.......................... $ 751.00 HY 9263C-CRU Flanged Cast Iron Viton® CW 23 lbs. CALL
AC FMC650FHYD Cast Iron Centrifugal Pump. 14.5 GPM HY 9263S-CB 1-1/4” x 1-1/2” FPT Stainless Silcarbide CCW 23 lbs. 889.00
Hydraulic Motor. Inlet 220 Full Port Flange & 1-1/2” NPT HY 9263S-CBU Flanged Stainless Silcarbide CCW 23 lbs. CALL
Outlet 200 Standard Port Flange & 1-1/4” NPT. HY 9263S-CBR 1-1/4” x 1-1/2” FPT Stainless Silcarbide CW 23 lbs. 831.00
140 GPM & 160 PSI. Single Mech. Seal. Wt. 43 lbs. 786.00 HY 9263S-CBRU Flanged Stainless Silcarbide CW 23 lbs. CALL
AC FMC650FHYDWS Same as Above but with Oasis™ Double Wet Seal. 1116.00 HY 3430-0332 Viton® Seal Repair Kit....................................................... 32.90
HY 3430-0589 Silcarbide Seal Repair Kit................................................... 110.00
AC FMC750FHYDM22 Cast Iron Centrifugal Pump. 18 GPM Hyd. Motor.
Note: Silcarbide Seal Option is Available on Cast Iron Units (B).
300 Series Flanged Suction x 220 Series Flanged
Discharge. 280 GPM & 150 PSI. Oasis™ Double
Wet Seal. Wt. 70 lbs.................................................. 1402.00
AC FMC750FHYDM25 Cast Iron Centrifugal Pump. 20 GPM Hyd. Motor. Diaphragm Pump Units
300 Series Flanged Suction x 220 Series Flanged with Power Pro Engines
Discharge. 290 GPM & 150 PSI. Oasis™ Double
Wet Seal. Wt. 70 lbs............................................... 1402.00 Units include Power
AC FMC850FHYD Cast Iron Centrifugal Pump. 23 GPM Hyd. Motor. Pro Engines with
300 Series Flanged Ports. 325 GPM & 150 PSI. control unit and
Oasis™ Double Wet Seal. Wt. 80 lbs...................... 1950.00 6:1 gear box.
For additional
D
specifications,
see individual
pumps. Can
Diaphragm be fitted
with Honda
Pump Units or Briggs
& Stratton
with Honda Engines Engines. You must have the D403HRGI-65
Hypro Diaphragm Pump & Engine units D pump mounting feature with 6:1
for general purpose ground or tree reduction and a 3/4” keyed shaft.
spraying. Develops pressures
to reach mid to upper spray Order Information
levels. Handles almost any Diaphragm Model Number Max. GPM Max. PSI Max. RPM Control Unit & Gearbox Engine & HP
fluid, including abrasives and Pump Units for D252GRGI-25 5.9 290 3600 9910-KIT1990 PowerPro 5.5 HP
suspensions with minimal wear. fertilizer, chemicals D30HRGI-65 9.6 580 3600 GS60GI & 8000-0056 PowerPro 6.5 HP
These pumps are equipped with and abrasives
a gear-reduction drive that is close D403HRGI-65 9.9 580 3600 GR40 & 8000-0056 PowerPro 6.5 HP
coupled directly to the gas engine. Pump runs at 540 RPM. Maximum temperature D503HRGI-65 14.3 290 3600 GR40 & 8000-0056 PowerPro 6.5 HP
is 140° F. Pump units include adjustable pressure controls. (Hose, gun and plumbing
are not included). Note: Spray height will vary with wind velocity.
Part No. HP GPM PSI WT. Net Ea.
Max. Spray DU D252-55 5.5 Recoil 5.9 290 52 lbs. $ 896.00
Part No. ENGINE GPM PSI Height Starter Wt. Net Ea. HY D30HRGI-65 6.5 Recoil 9.6 580 75 lbs. 1288.00
DU 5H-D403GR 5.5-HP Honda 10.6 500 35'-40' Rewind 90 lbs. $ 1632.00
HY D403HRGI-65 6.5 Recoil 9.9 580 70 lbs. 1338.00
DU 8H-D50GR 8-HP Honda 15 580 45'-50' Rewind 130 lbs. 2189.00
DU 13H-D813GR 13-HP Honda 21.4 725 50'-57' *12-Volt 160 lbs. 2898.00 HY D503HRGI-65 6.5 Recoil 14.3 290 80 lbs. 1552.00
DU 18H-D1064G † 20-HP Honda 28 725 60'-68' *12-Volt 190 lbs. 3775.00 For 6.5 HP Briggs Intek - ADD about $145.00. For Honda - ADD about $310.00.
* 12-Volt Electric start models include battery holder & cables. No battery.
† 20 HP Model includes unmounted 3.0 gallon fuel tank & 4-1/2' fuel hose. Viton® is a registered trademark of DuPont Performance Elastomers
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0805
HYPRO Hydraulic Centrifugal Sprayer Pumps 121
Threaded Hydraulic Drive Centrifugal Pumps Flanged Hydraulic Drive Centrifugal Pumps
9303 & 9306 Series • Cast Iron • Stainless 9303 & 9306 Series • Cast Iron • Stainless
Features:
• Available in Cast Iron & 316 Stainless Steel
• Hydraulic Motor Drive (for open center, closed center & load-sensing systems)
• 1-1/2” NPT Inlet, 1-1/4” NPT Outlet or 2” x 1-1/2”
• Temperatures to 140° F.
• Impeller: Cast Iron Models are Nylon & Stainless Steel Models are Polypropylene D D
Cast Iron
• Hydraulic Motor is Internal Gear Gerotor
• Cast Iron Models have Viton®/Ceramic Seals & Stainless Steel Models have Life
Stainless Steel
Guard® Silicon Carbide Seals Features:
• Maximum Motor PSI is 3000 • Available in Cast Iron & 316 Stainless Steel
9303C Cast Iron
• Hydraulic Motor Drive (for open center, closed center & load-sensing systems)
• Temperatures to 140° F.
• Impeller: Cast Iron Models are Nylon & Stainless Steel Models are Polypropylene
• Hydraulic Motor is Internal Gear Gerotor
• Cast Iron Models have Viton®/Ceramic Seals & Stainless Steel Models have Life
Guard® Silicon Carbide Seals
• Maximum Motor PSI is 3000
D
• Cast Iron Pumps are also FPT. Performance Specifications are in chart at left.
Cast Iron Flanged Connection - Viton® Seals
D Part No. Material Flange Size* Net Ea.
HY 9303C-HM1CU Cast Iron 200x220 $ 591.00
9303S Stainless HY 9303C-HM3CU Cast Iron 200x220 626.00
HY 9303C-HM5CU Cast Iron 200x220 591.00
HY 9306CHM1CU † Cast Iron 200x220 744.00
Order Information HY 9306CHM3CU Cast Iron 200x220 723.00
Max. Max. Max. HY 9306CHM5CU Cast Iron 200x220 687.00
Model # GPM PSI Hyd. GPM Hydraulic Selection System * 200 x 220 = 2” x 2” Full Port. † With SC Seal.
9303-HM1 114 130 13 GPM Open/Closed Stainless Steel Flanged Connection - SilCarbide Seals
9303-HM2 97 95 6 GPM Open/Closed Part No. Material Flange Size* Net Ea.
HY 9306S-HM1C-3U Stainless 300x220 $ 1313.00
9303-HM3 125 98 24 GPM Open/Closed
HY 9306S-HM3C-3U Stainless 300x220 1351.00
9303-HM4 115 93 7 GPM Open/Closed
HY 9306S-HM5C-3U Stainless 300x220 1313.00
9303-HM5 147 145 16 GPM Open/Closed
300 x 220 = 3” x 2” Full Port
*
9306-HM1 207 130 13 GPM Open/Closed
Accessories
9306-HM3 214 135 24 GPM Open/Closed Part No. Description Net Ea.
9306-HM5 212 140 17 GPM Open/Closed HY 3430-0456 Vent Line Kit...................................... $ 6.10
3430-0332 Seal and O-ring Repair Kit HY 2120-9 Viton® Seal....................................... 29.05
3430-0589 Life Guard® Silicon Carbide Seal Kit HY 3430-94 Hydraulic Motor Kit for 9200............. 5.96
HY 3430-0748 Hydraulic Motor Kit for 9300............. 43.95
Cast Iron Threaded Connection - Viton® Seals HY 3430-0332 Repair Kits for 92/93/94 Cast Iron Pumps 32.90
Part No. Material Size Net Ea.
HY 9303C-HM1
HY 9303C-HM2
Cast Iron
Cast Iron
1-1/2” x 1-1/4”
1-1/2” x 1-1/4”
$ 567.00
567.00
Hydraulic Driven Cast Iron Pump
HY 9303C-HM3 Cast Iron 1-1/2” x 1-1/4” 602.00 High Volume
HY 9303C-HM4 Cast Iron 1-1/2” x 1-1/4” 567.00
HY 9303C-HM5 Cast Iron 1-1/2” x 1-1/4” 567.00 • Port Sizes: 3” x 2” FPT or Flanged
HY 9306CHM1C Cast Iron 2” x 1-1/2” 664.00
HY 9306CHM3C Cast Iron 2” x 1-1/2” 700.00 • Silicon Carbide Seal
HY 9306CHM5C Cast Iron 2” x 1-1/2” 664.00 • Hydraulic Motor: Internal Gerotor
Stainless Steel Threaded Connection - SilCarbide Seals • Hydraulic Ports: 7/8” Inlet &
Part No. Material Size Net Ea. 1-1/6” Outlet SAE Straight-thread
HY 9303SHM1 Stainless 1-1/2” x 1-1/4” $ 1039.00 ports O-ring Boss.
HY 9303SHM3C Stainless 1-1/2” x 1-1/4” 1077.00 D
HY 9303SHM4 Stainless 1-1/2” x 1-1/4” 1039.00 • GM10 is 16-20 GPM Hydraulic &
HY 9303SHM5 Stainless 1-1/2” x 1-1/4” 1039.00 GM12 is 16-23 GPM Hydraulic
HY 9306SHM1C Stainless 2” x 1-1/2” 1229.00 • Maximum Motor PSI: 3000
HY 9306SHM3C Stainless 2” x 1-1/2” 1266.00 Continuous Duty
HY 9306SHM5C Stainless 2” x 1-1/2” 1229.00
9307C-GM10 • Requires 20 GPM Oil @ 3,000
PSI for High Volumes
Life Guard TM
Hyd. Flow GPM @ GPM @ GPM @ GPM @ GPM @ GPM @ GPM @ GPM @ GPM @
Silicon Carbide Seals GPM
16
30 PSI
282
40 PSI
253
50 PSI 60 PSI 70 PSI 80 PSI
219 168 73
90 PSI 100 PSI 110 PSI
Standard seal in all Hypro stainless centrifugal 17 318 288 258 222 174 95
pumps. 8X life with abrasive solutions over ceramic. D
18 346 318 291 258 222 166 90
a run dry survivability over ceramic. This is a superior 19 361 338 311 281 250 201 137
seal which will provide outstanding performance. For any 20 370 351 328 301 275 241 184 106
pump listed with a silicon carbide seal option, add suffix B.
Price adder approximately $53 with new pumps. Seal kits Max. Max. Max. Max. Wt.
include seal and o-ring. Part No. Description Oil Temp. GPM PSI Lbs. Net Ea.
Part No. Silicon Carbide Seal Kits Net Ea. HY 9307C-GM10 Hyd. C.I. Pump 20 140° F. 370 135 86 $ 2777.00
HY 3430-0589 For 9200, 9300, 9400 Pumps............. $ 110.00 HY 9307C-GM10-U Hyd. C.I. Pump* 20 140° F. 370 135 86 2800.00
HY 3430-0590 For 9000P Pumps............................... 125.50 HY 9307C-GM12 Hyd. C.I. Pump 23 140° F. 370 135 86 2777.00
HY 3430-0591 For 9000 Series Pumps...................... 115.50 HY 9307C-GM12-U Hyd. C.I. Pump* 23 140° F. 370 135 86 2800.00
HY 3430-0593 For 9300P, 9400P, 9500P Pumps....... 121.00 HY 3430-0604 Silicon Carbide Seal Kit.......................................... 255.00
HY 3430-0601 For 9305C Pumps Only ..................... 111.00 * 300 x 220 Flanged
Viton® is a registered trademark of DuPont Performance Elastomers
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0237
122 HYPRO Centrifugal Sprayer Pumps
9000 Series PTO Drive
Centrifugal Pumps Pedestal Mount
Cast Iron Centrifugal Pumps
Series 9000 Pumps feature Cast Iron & Stainless
a planetary oil lubricated
gear drive, Viton® seals, a
glass-filled nylon impeller Series 9200C features a bearing pedestal, Viton®
with a stainless wear ring, seals, *CCW pump shaft rotation (9203C-R is CW)
and CCW pump shaft rota- and a glass-filled nylon impeller with stainless steel D
tion. Uses 90 wt. gear lube. wear ring. Maximum fluid temperature is 140° F.
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0236
Centrifugal Transfer & Sprayer Pumps 123
1537A 1536
D
shaft & Noryl impeller • Ports are 1-1/2" FPT • Mechanical seal with Buna GPM 104 100 94 82 70 50
elastomers is standard • Designed for continuous duty • Single phase motors PSI 10 20 30 40 50 60 70
to 1-1/2 HP are 115/230 volt, 2 & 3 HP are 230 volt • Three phase motors GPM 110 106 96 88 80 60 30
are 230/460 volt and require separate starters • Maximum temperatures PSI 0 10 20 30 40 50 60 70
to 140° F. GPM 150 147 145 140 130 120 107 97
1550
PSI 80 90 100 110 120 130 140
For water and other liquids GPM 87 80 69 57 45 36 16
GPM Data with 1.0 S.G.
1550-SP 1538SP
PSI 10 20 30 40 50 60
Model
GPM 98 87 73 60 44 21
1537A
PSI 10 20 40 60 80 100 120
GPM 145 141 118 93 71 49 28
D Model GE1600
Shown with
Engine
ACE GE1600 PERFORMANCE DATA
Engine 20 40 60 80 100 120
Shaft PSI PSI PSI PSI PSI PSI
Canadian Standards Association D Speed GPM GPM GPM GPM GPM GPM
3900 RPM 280 220 180 140 80 0
Underwriters Laboratories
3500 RPM 280 220 175 130 40 0
3200 RPM 280 220 170 100 0 —
Part No. Motor Max. S.G. Wt. Net Ea.
GL GT07 3/4 HP - 1 Ph. 1.0 48 lbs. $ 335.00 Part No. Pump Size GPM PSI Wt. Net Ea.
GL GT10 1 HP - 1 Ph. 1.0 52 lbs. 344.00 HY 1536 1-1/2" x 1-1/4" 104 70 5 HP Briggs 54 lbs. $ 625.00
GL GT15 1.5 HP - 1 Ph. 1.0 60 lbs. 374.50 HY 1537A 1-1/2" x 1-1/4" 110 70 5.5 HP Honda 73 lbs. 753.00
GL GT153 1.5 HP - 3 Ph. 1.0 55 lbs. 405.00 HY 1521C-65 1-1/2” x 1-1/4” 104 70 6.5 HP PowerPro 65 lbs. 582.00
GL GT20 2 HP - 1 Ph. 1.0 65 lbs. 502.00 HY 1538SP5 2" x 2" * 98 60 5.5 HP Honda 80 lbs. 971.00
GL GT203 2 HP - 3 Ph. 1.0 60 lbs. 552.00 HY 1550 2" x 1-1/2" 150 140 9 HP Honda 107 lbs. 1302.00
GL GT30 3 HP - 1 Ph. 1.0 76 lbs. 732.00 HY 1550-SP 2” x 2” * 148 130 9 HP Honda 134 lbs. 1645.00
GL GT303 3 HP - 3 Ph. 1.0 71 lbs. 771.00 HY 1552C-130 2” x 1-1/2” † 150 140 13 HP PowerPro 165 lbs. 1171.00
HY 1552C-130E 2” x 1-1/2” 150 140 **13 HP PowerPro 165 lbs. 1205.00
HY 1538 1-1/2" x 1-1/4" Hypro Wet End Pump Only.......... 45 lbs. 286.50
Thermoplastic Self-Priming HY 1538SP
HY 1551
2" x 2" *
2" x 1-1/2"
Hypro Wet End Pump Only ......... 65 lbs. 494.50
Hypro Wet End Pump Only.......... 44 lbs. 544.00
Sprinkler Pumps HY 1551-SP
AC GE800
2” x 2” *
2" x 1-1/2"
Hypro Wet End Pump Only ......... 65 lbs. 900.00
Ace Wet End Pump Only. Fits
- Sta-Rite “PD” Series - 1” Threaded Shaft........................... 55 lbs. 542.00
AC GE1600 2-1/2" x 2" Ace Wet End Pump Only. Fits
1” Threaded Shaft........................ 60 lbs. 712.00
Specifications:
* Self-Priming Model. ** Electric Start. Note: 1538 fits both 1536 & 1537A Pump Units.
Body & Base - † No Baseplate Included, but available.
Fiberglass-reinforced
D
thermoplastic
The Best Advanced Circulating Pumps
U.L. Listed.
Impeller - Engineered
polymer
MP Pumps for Transit Buses or School Buses. . .
Diffuser - Polypropylene
Shaft - Stainless Steel MP Circulator Bus Pumps are highly reliable
and proven in many applications
around the world. Precision tested
Performance (Capacity in Gallons Per Minute)
Disch. PD2HE PD2HF PDHG PDHHG
materials with consistently high
Press. Distance Above Water control standards.
PSI 5' 10' 15' 20' 25' 5' 10' 15' 20' 25' 5' 10' 15' 20' 25' 5' 10' 15' 10' 25'
10 53 52 50 48 46 67 66 64 61 59 70 69 67 64 62 90 88 86 82 80 Transit Bus Pump Features:
20 45 42 39 37 35 59 56 54 50 47 61 59 56 53 50 79 76 72 70 65 Pumping capacities from 3.7
30 35 31 27 24 18 48 44 40 37 32 50 48 44 41 37 66 62 57 55 50
40 17 10 31 26 20 10 36 33 25 23 19 50 45 42 37 32 GPM to 26 GPM • Unique D
50 16 9 30 23 20 design allows for high mechanical
efficiency at low voltage • Direction of
Quick priming • Lightweight yet strong construction • Single Phase. discharge can be at any angle • Hard face
Applications: Lawn & landscape sprinkling; self primer out of tanks or cisterns mechanical Seal • Series-wound and permanent
• Light chemical transfer for compatible fluids; call with liquid details. magnet motors available • Brush life up to 15,000 hours
• Easy serviceability. Weight is 9 lbs.
Port Sizes Motor Wt. School Bus Pump Features: Cover Material and adapter are aluminum
Part No. HP Suction Discharge Voltage Lbs. Net Ea. with clear anodized coat • Nickel steel impeller • Slip-on hose connections
SA PD2HE 1 2” 1-1/2” 115/230 38 $ 325.00 for 1-1/8" hose • Carbon/ceramic seal • Motors are permanent magnet with
SA PD2HF 1-1/2 2” 1-1/2” 115/230 41 377.00 non-replaceable brushes (estimated service life is 4000 hours) • 12-volt
SA PD2HG 2 2” 2” 230 52 439.00
design only • Weight is 4 lbs.
SA PDHHG 2-1/2 2” 2” 230 54 489.00
Motors are open-drip standard; 1 phase.
OTE: All motors are shipped from the factory at 230 volt. 1 and 1-1/2 HP pumps also feature
N Part No. Bus Type Voltage Base Seal Net Ea.
dual voltage motors. Easy to change voltage settings require switching only 2 wires to reset MX 28691 Transit, New Style 24 None Hard Faced $ 495.29
voltage. Just remove the dust cover and change the 2 leads on the terminal board as shown on MX 28987 School Bus 12 Yes Carbon/ceramic 215.47
motor nameplate. Note: Transit Pumps will require inlet & outlet flanges if they are not included in existing system.
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0238
124 Centrifugal Sprayer Pumps
Turbine Pump from Hypro Polypropylene Centrifugal Pumps
High Capacity for 1000 RPM/PTO Drives
Hypro’s Polypropylene Centrifugal Pumps ensure long life because of their
excellent corrosion resistant characteristics. The lightweight polypropylene
pump is the first choice for handling acid based fertilizers. All parts
in contact with the fluid pumped are manufactured of 30% glass-filled
polypropylene. 1-1/2” x 1-1/4” FPT; Carbon-Ceramic Viton® Mechanical Seal.
At 1000 RPM It Will Deliver
35 GPM @ 50 PSI PTO - GEAR DRIVEN
540 or 1000 RPM
28 GPM @ 60 PSI
19 GPM @ 70 PSI The proven, smooth-running gear
mechanisms used in Hypro’s standard
9000 Series pumps are utilized for
Model 9600C is a high increasing PTO speed. Gears are safely
D capacity, low pressure pump. enclosed in the factory lubricated case.
It is designed specifically for Available in a Gear Driven 1” Solid Shaft
1000 RPM PTO’s. with 1-3/8” PTO spline (9006PO-6 spline; D
9008PO-21 spline). CCW rotation when
facing shaft.
Features: 1-1/2" Ports • 15/16" Shaft with 1/4" keyway • heavy duty sealed
bearings • Cast Iron body • Valox Impeller • Stainless Shaft • Viton® Lip Seal.
Note: Use with 1320-80 (1-3/4") or 1320-78 (1-3/8") Couplers.
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0235
Low Volume Utility Transfer Pumps 125
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0849
126 Centrifugal, Roller & Flex Impeller Pumps
Bronze Body
Centrifugal Flex Impeller Pumps
Pumps Ideal choice for a wide variety of
pump applications. Works well on mild
abrasive fluids, and fluids with particles
Hypro’s Noryl Body Straight
in suspension. No metal or metal
Centrifugal Pumps by Shertech are
contact. Continuous operation. Easy
designed for bulk transfer of fertilizers
D to service. D
and chemicals. Noryl has excellent
chemical resistance to acids, alkalis Nitrile impeller and lip seal is resistant
and inorganics. Call for chemical to petroleum based oils and fuels, silicon
compatibility check. greases and hydraulic fluids. Operate at
1724 or 3450 RPM. 10' lift when primed. Self
Specifications: Temperatures to 140˚F. • 1-1/2 ports • 3450 TEFC Motors priming to 3 ft., but DO NOT LET the pump
• Viton® Mechanical Seals. run dry.
GPM@20 PSI HP Req'd.
Performance Data
Part No. Ports 1725 RPM Shaft @1725R Wt. Net Ea.
PSI 41 37 30 25 4 SR R50GN Impeller Pump 3/4" 9.4 5/8 3/4 6 lbs. $ 373.50
GPM 0 30 60 90 120 SR R102N Impeller Pump 1" 16.4 5/8 1-1/2 7 lbs. 382.50
Bronze Impeller
Part No.
DU PM4000
Chemical Transfer Pump Wt.
With 1 H.P. TEFC Motor 49 lbs. $ $ 764.00
Net Ea.
Pump Units
DU PM4000-XL Same with 4001XL Pump 49 lbs. 818.00
These base mounted pumps
are ideal for waste oil transfer
ROLLER & PISTON PUMP UNITS and other fluids compatible
with buna impellers.
For high viscosity products use D
D GPM@15 PSI
Part No. * Water Motor Wt. Net Ea.
DU PM2135 18 GPM 1-1/2 HP, 110V 54 lbs. $ 931.00
* Flow rates are based on 5' discharge head.
Model
PM5075H
HYPRO ENGINE UNITS: All units are pre-assembled but are less all plumbing
and fittings. Engines have gear reduction for 600 RPM. Visit Our Web Site at
PM5075: Includes a N7560CR roller pump mounted as shown with a Briggs &
Stratton or Honda 5 HP Gear reduction engine. Maximum pressure is 200 PSI.
http://www.dultmeier.com
PM8015H: Includes a 1502XL roller pump long coupled to a Honda 8 HP gear or E-Mail us at
reduction engine. 21 GPM and maximum pressure to 150 PSI.
dultmeier@dultmeier.com
Part No. Engine HP HYPRO PUMP GPM @PSI Wt./Lbs. Net Ea.
DU PM5075 B&S 5 7560N 10 200 78 $ 952.00
DU PM5075H Honda 5 7560C 10 200 78 1099.00 Viton® is a registered trademark of DuPont Performance Elastomers
DU PM8015H Honda 8 1502XL 21 150 110 1785.00
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0753
PTO Adapters & Pump Repair Parts & Kits 127
2 2000-4 Bearing
2 2107-2 Seal
For
R15 Kit For: R65 Kit For: Coupler Pump FOR PTO SHAFT:
1500 Roller Pumps 6500 & 6600 Roller Pumps Part No. Type Shaft RPM Size Splines Material Net Ea.
HY 1320-77 Standard 5/8" 540 1-3/8" 6 Forged Steel $ 21.45
Qty. Includes: Qty. Includes: HY 1320-76 Standard 15/16" 540 1-3/8" 6 Forged Steel 22.35
6 1005-5 Super Rollers 6 1005-4 Super Rollers HY 1320-80 Standard 15/16" 1000 1-3/4" 20 Forged Steel 40.95
1 1720-3 O-Ring 1 1720-8 O-Ring HY 1320-78 Standard 15/16" 1000 1-3/8" 21 Forged Steel 27.05
2 2008-1 Bearing 2 2000-4 Bearing HY 1323-77 Quick Cplr. 5/8" 540/1000 1-3/8" 6/21 Forged Steel 32.15
2 2112-3 Seal 2 2107-2 Seal HY 1323-76 Quick Cplr. 15/16" 540/1000 1-3/8" 6/21 Forged Steel 32.15
DL 35992 Quick Cplr. 15/16" 1000 1-3/4" 20 Forged Steel 54.20
R17 Kit For: R75 Kit For:
1700 Roller Pump Series - 7500 Roller Pump
Repair Kits for Delavan Centrifugal Pumps
Qty. Includes: Qty. Includes:
5 1005-5 Super Rollers 8 1005-4 Super Rollers
1 1720-99 O-Ring 1 1720-14 O-Ring
DL 35745 KIT Includes:
2 2008-1 Bearing 2 2008-1 Bearing For Centrifugal Pumps (1) 34912 Pump Gasket
2 2112-3 Seal 2 2112-3 Seal No's. 34945-1 or 35566-1 (1) 34944 Locknut Cap
(1) 34942 Washer
(1) 34943 Face Seal Assembly
R40 Kit For: R77 Kit For: Part No. Net Ea. (1) 35278 Slinger Gasket
Series - 4000 Pump-1979 on 7700 Roller Pumps DL 35745 $ 51.35
Qty. Includes:
Qty. Includes:
7 1005-4 Super Rollers
4 1005-2 Super Rollers
1 1720-14 O-Ring
1 1720-104 O-Ring
2 2008-1 Bearing
2 2000-4 Bearing
2 2112-3 Seal
2 2107-2 Seal
CENTRIFUGAL PUMPS
R90 Repair Kit For: 9000 Series R90P Kit For:
Gear Drive Centrifugal Pumps Gear Driven Poly Pumps
Visit Our Offices in Omaha, Nebraska
Qty. Includes: Qty. Includes:
8 1450-4 Cushion 1 2120-11 Viton® Seal
and Davenport, Iowa
2 1610-12 Key 1 1721-83 O-Ring
1 1720-83 O-Ring 1 1720-139 O-Ring
1 1810-1 Retainer 1 2130-17 Bearing
1 1810-11 Retainer 1 1700-98 Gasket
2 1810-13 Retainer 1 2008-1 Bearing
1 1820-6 Retainer 1 2005-2 Bearing
1 1800-14 Retainer 4 1450-4 Cushion
1 2008-1 Bearing 1 2270-57 Washer
1 2005-2 Bearing 1 2250-51 Jam Nut
3 2007-22 Race 1 1150-52 Nut Seal
1 2253-1 Nut 2 1610-12 Key
2 1810-13 Retainer
6 2265-3 Washer
1 1820-25 Retainer
1 2120-11 Mechanical Seal
3 2007-22 Inner Race
1 2130-17 Lip Seal 601 West 76th St.
NOTE: Order Gears Separately
1 1810-11 Retainer 13808 Industrial Road
1 1800-14 Retainer Omaha, NE 68137 Davenport, IA 52806
1 2102-25 Oil Seal
1 1810-1 Retainer 1-800-228-9666 • 1-402-333-1444 1-800-553-6975 • 1-563-386-0930
Repair Kits For: 9200/9400 Series FAX: 1-402-333-5546 FAX: 1-563-386-5448
Cast Iron Pumps
3430-0445 Repair Kit For:
R92 for 9200/9400 Hydraulic & Pedestal
e-mail: dultmeier@dultmeier.com
Qty. Includes: Poly Pumps
1 1410-56 Slinger website: dultmeier.com
1 1610-4 Key Qty. Includes:
1 1610-15 Key 1 2120-11 Viton® Seal
1 1720-83 O-Ring 1 1720-83 O-Ring
2 1810-14 Retainer 1 2270-57 Washer
1 1820-13 Retainer 1 2250-51 Washer
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0247
128 Hypro & Delavan Roller Pumps
4000 Series
High Speed, 4-Roller Pumps The Roller Pumps on this page are used mainly in agriculture, park and turf
Two models are available. management and pest control. They operate efficiently at tractor PTO speeds,
will handle suspensions of non-abrasive wettable powders and will tolerate
Model 4001 to 1800-RPM & Model 4101 to 2600- considerable wear before performance is adversely affected. Body: Cast iron,
RPM . These pumps are popular for use on gas Ni-Resist or Silver Cast®. Seals: Viton® is standard on 1700, 4000, 6500 and
engine powered portable sprayers, as they can run 7560 Series. Buna-N is standard on the 1500 series. Shafts: are all of Stainless
at speeds up to 2600 RPM. They will pump oils, Steel. Rollers: These pumps are all supplied with a composite roller of nylon and
D distillates and many other chemicals. Maximum polypropylene; Teflon and Buna-N rollers are available for specific applications.
temperature is 140° F. Weight is 5 lbs.
Capacity: to 8-GPM @ 50 PSI Super Rollers XL Silver Cast® Pumps
Shaft: 5/8" O.D. Stainless Steel Ports: 3/4" FPT Silver Cast is a new alloy developed by Hypro which is harder, wears better and
Seals: Viton® Max. Pressure: 150 PSI is more corrosion resistant than any other casting material used in Ag Roller
Pump Shaft Rotation: CW when facing shaft Bearings: Shielded Ball Pumps. These pumps will outlast cast iron models by 10 times. Use on
Performance Roundup™ type products.
0 PSI 25 50 75 100 125 150
6500 Series
800
* 900
34.5 1.85
40.0 2.63
32.5 3.20
38.0 3.95
29.5 4.75
35.0 5.40
28.0 6.20
- -
3/4" Ports 6-Rollers * 1000 43.0 3.00 41.0 4.67 39.0 6.07 - -
* For 900 & 1000 rpm speeds. Recommended continuous duty maximum pressure -
An extremely versatile pump despite low cost. 100 PSI (.69 MPa): Recommended intermittent duty maximum pressure-150 PSI.
Available in Ni-Resist, Cast Iron and Silver
Cast® construction. Equipped with Viton® seals, Part No. Net Ea.
sealed bearings. Maximum Temperature is HY 1700C Cast-Iron Pump, Less PTO Coupler........... $ 220.50
140° F. Metallic rotor. Weight is 9 lbs. HY 1700N Ni-Resist Pump, Less PTO Coupler........... 457.00
HY 1700XL Silver Cast® Pump, Less PTO Coupler..... 618.00
Max. RPM: 1200 Capacity: to 21 GPM DU R17 Repair Kit. with Super
D Rollers, Seals & Bearings............................ 52.70
Shaft: 5/8" O.D. Max. Pressure: 300 PSI
Seals: Viton® Super Rollers NOTE: Use 1"
Suction Line at speeds
Pump Shaft Rotation: CW or CCW when facing shaft
SPEED 0 PSI 50 PSI 100 PSI 150 PSI 200 PSI 250 PSI 300 PSI
above 800 RPM.
1500 Series - High Capacity
RPM GPM HP GPM HP GPM HP GPM HP GPM HP GPM HP GPM HP 1-1/2" Ports 6-Rollers
540 10.2 .09 8.1 .58 7.5 .83 6.7 1.16 6.0 1.45 5.1 1.81 4.1 2.14
600 11.4 .10 9.1 .65 8.6 .90 7.7 1.27 7.2 1.62 6.1 2.01 5.4 2.36 Capacity: to 60 GPM Max. Temp: 140° F.
800 15.1 .17 12.9 .86 12.3 1.21 11.3 1.68 10.9 2.14 10.1 2.65 9.4 3.13
1000 18.7 .25 16.4 1.11 15.8 1.54 14.7 2.13 14.2 2.69 13.5 3.33 12.6 3.99
Max. Pressure: 150 PSI Max. RPM: 1000
1200 21.9 .39 19.7 1.40 18.9 1.93 18.1 2.69 17.5 3.35 16.8 4.14 16.0 4.93 Shaft: 15/16" O.D. Seals: Buna-N D
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0246
Hypro Diaphragm Pumps 129
Hypro Diaphragm Pumps are the most complete line of pumps available for spraying and pumping of herbicides, pesticides, liquid fertilizer and hard-to-handle
fluids. Hypro offers a wide rang of flows and pressures for slurries and suspensions. Pressures for row crop to treetop spraying applications range from 20 to
725 PSI with flow rates from 3.5 to 66 GPM. Low cost maintenance and almost wear-free operation.
These models can handle fluids up to 140° F. and can be run dry. Hypro diaphragm pumps can be driven by 540 rpm PTOs, 3 to 25 HP gasoline engines,
electric or hydraulic motors.
Features: Anodized aluminum or epoxy-coated housings • Check valves include nylon cages & stainless springs • Oil-bath design and premium quality Desmopan
(polyurethane) diaphragms provide longer life and greater reliability • Self-priming operation • Wide spectrum of flows and pressures • Corrosive, abrasive and
general use chemical compatibility. (Call for chemical compatibility) • Visual oil-level sight glass. Note: 40 - 50 Mesh screen recommended upstream of pumps.
HY 9910-D250 66.0 290 550 17 Pump Only - 1-3/8"-6B Male Spline thru Shaft.............. 2085.00
* For shaft kits see Hypro Accessories Page. † Gas Engine. Above pumps have epoxy coated housings. DP423GRGI
Polypropylene
D
D D
D
D 9910-D403
9910-D30 9910-D50 9910-D503
9910-D2522
Max. Max. Max.
Part No. GPM PSI RPM Req’d HP MEDIUM PRESSURE DIAPHRAGM PUMPS: Wt. Net Ea.
HY 9910-D252 6.0 290 650 2 Pump Only with 3/4" solid keyed shaft ....................... 13 lbs. $ 448.00
HY 9910-D252GRGI 6.0 290 3600 2 Same as above with Control Unit & Gearbox ............. 15 lbs. 620.00
HY 9910-D30 * 9.5 580 550 5 Pump Only, Less Shaft . ............................................. 23 lbs. 560.00
HY 9910-D30AP-A 9.5 580 550 5 Same as above with 3/4" solid extended shaft . ......... 23 lbs. 598.00
HY D30HRGI 9.5 580 3600 5 Pump Only with Control Unit & HD Gearbox............... 33 lbs. 940.00
HY 9910-D403 * 10.6 580 550 6 Pump Only, Less Shaft................................................ 23 lbs. 580.00
HY D403HRGI 10.6 580 3600 6 Same as above with HD Gearbox & Control Unit........ 27 lbs. 1032.00
HY 9910-D50 * 14.0 580 550 8 Pump Only, Less Shaft................................................ 34 lbs. 794.00
HY 9910-D50AP-A 14.0 580 550 8 Same as above with 1" solid extended shaft . ............ 35 lbs. 831.00
HY 9910-D503 * 15.0 580 550 9 Pump Only, Less Shaft................................................ 28 lbs. 794.00
HY D503HRGI 15.0 580 3600 9 Same as above with HD Gearbox & Control Unit........ 40 lbs. 1246.00
* For shaft kits, pressure controls & gear reduction kits see Hypro accessories page. † Gas Engine.
Above have epoxy coated housing except for D30 & D50 groups which are anodized aluminum.
9910-D813
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0266
130 Udor Diaphragm Pumps
UDOR Diaphragm Pumps for a wide variety of spraying applications. Ideal for use in lawn, turf, tree
and agricultural field spraying. Pumps are self-priming and can be run dry. Designed to handle liquid
fertilizers, abrasive materials, suspension products, pesticides, de-icing liquids and other hard to handle
products. Can be driven by PTO, gas engines, hydraulic motors or belt drive. Rated for temperatures
to 140˚ F. Maximum speed on all models is 540 RPM.
Standard Features Include: Urethane Diaphragms • Anodized, die cast aluminum crankcase •
Heat-treated crankshaft • Stainless steel check valves • Heavy-duty connecting rods • Self-lubricating
piston sleeves. D
All pumps include adjustable pressure control, pulsation dampener and gauge. Available with solid
shafts for pulley drive or in gear reduction units with gear boxes for gas engine drive. (Mounting rails
are standard on pulley drive units). Note: Pumps with spline shafts can be PTO driven or adapted to
pulley drive with hubs shown below. IOTA-20GR
KAPPA-55GR
KAPPA-120GR
D
D
D
KAPPA-75GR KAPPA-100C
Drive Accessories
#10 Hubs convert 1-3/8” splined shafts to pulleys that take H or Q hubs as noted. Number of grooves for pulley drive
will be determined by flow and pressure requirements of pump.
D
Part No. Hubs for use on Pump Model Net Ea.
UD 10H6 H Bushing for pulley driving pumps with 1-3/8” spline, up to 2 groove................ $ 19.85
UD 10Q1 Q Bushing for pulley driving pumps with 1-3/8” spline, up to 3 groove................ 53.30
UD 10Q2 Q Bushing for pulley driving pumps with 1-3/8” spline, up to 5 groove................ 57.00
10Q2 TREE SPRAYING SELECTION GUIDE:
HYPRO
Height Pump Capacity Spray Gun Nozzle Gas HP
30-35 ft. KAPPA25 6 GPM 3381-10 3385-3000 3 HP
275 PSI 3381-13
35-40 ft. KAPPA43 9.5-10.5 GPM 3381-10 3385-3000 5 HP
550 PSI 3381-13
45-50 ft. KAPPA55 14 - 15 GPM 3381-11 3385-4000 8 HP
550 PSI
50-57 ft. KAPPA120 21 GPM 3381-11 3385-4500 14 HP
700 PSI
60-68 ft. KAPPA120 28 GPM 3381-11 3385-6000 18 HP
700PSI
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0718
John Blue & John Bean Pumps 131
Excellent for acidic and highly corrosive products including 50% Sulfuric Acid, agchemicals, lawn care chemicals, fertilizers and many other products
including heads that are constructed of polypropylene structure over aluminum diecast “core” for superior strength and chemical resistance.
Desmopan or HPS diaphragms with 316SS diaphragm bolts and washers. 316SS inlet and outlet check valves. Oil sight gauge.
Pressure Control Units
Part No. Net Ea.
BU SC-1066-2 Pressure Control Unit (Less Gauge) for DP43P & DP43-GRP Pumps: (2) 3/8” Outlets D
with Main Shuf-Off Valve & Pressure Regulator. 6.6 GPM & 290 PSI.......................................... $ 54.95
BU SC-2420-3 Pressure Control Unit (With Gauge) for DP193PP, DP282P & DP332P Pumps: (3) 3/4” Outlets
with Individual Shut-Off Valves, Main Shut-Off Valve & Pressure Regulator. 42 GPM & 290 PSI 249.50
SC-2420-3
BU SC-1480-3 Pressure Control Unit for DP392: (3) 1/2” Outlets with
with Individual Shut-Off Valves, Main Shut-Off Valve & Pressure Regulator................................ 224.00
Gear Reduction Units & Hydraulic Motor Adapters
Part No. Net Ea.
BU DP-318874 Gear Reduction Unit for DP193PP, DP282P & DP332P Pumps; SC-1066-2
Fits 5 HP Gas Engine with 1/2” Keyed Shaft................................................................................ $ 301.50
BU DP-31874897 Hydraulic Motor Adapter (SAE “B”) for DP43P Pump.................................................................. 275.50
BU DP-31874997 Hydraulic Motor Adapter (SAE “B”) for DP193PP, DP282P & DP332P Pumps........................... 203.00
BU DP-31155907 “Spacer” for Gear Reduction Unit & Hydraulic Motor Adapter for DP282P & DP332P Pumps (req’d). 99.85 D
BU DP-86357500 Bolts for “Spacer” Above (4 Required) ........................................................................................ 3.38
Pumps
For Grounds Care, Trees, Nurseries, Road Side, Pest Control & Golf Courses
These rugged piston pumps have cast iron cases, with hardened crankshafts and ball-type main bearings which are seated in oil for long life, non-wear ceramic
cylinders and spring loaded disc-type stainless valves.
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0724
132 Hypro Diaphragm Pumps & Accessories
ACCESSORIES for HYPRO 1" Solid Shaft Kits
D
Part No. GPM PSI CONTROL UNITS TO MOUNT ON: PUMPS Net Ea.
HY 9910-KIT1990 6 290 9910-D252 pumps. Includes relief valve &
6:1 Gear Reduction Kits
pressure/bypass selector. 5/8" HB bypass port Part No. GEAR REDUCTION KITS FOR: Wt. Net Ea.
& 3/8" HB outlet.................................................... $ 77.90 HY 9910-KIT1640 9910-D30, -D50, -D303 & -D403 Pumps.
HY 9910-GR40 11 580 9910-D303, & -D403 pumps. Includes adjustable 6:1 gear box for std. 5-HP gas engine
high pressure relief valves, complete bypass lever, with 3/4" shaft............................................. 7 lbs. $ 366.00
2-1/2" gauge, outlet barbs & 5/8" bypass barb . ... 193.50 HY 9910-KIT1642 9910-D50, -D503, -D813, -D1064 &
HY 9910-RM40 24 580 9910-D503 pumps. Includes high pressure -D1265 pumps. 6:1 gear box for standard
relief valve & (2) 1/2" HB outlets with individual 8-18 HP gas engine with 1" shaft................ 9 lbs. 457.50
shut-offs. Can be either direct or remote mtd....... 193.50
HY 9910-GS40GI 21 580 9910-D30 & D50 pumps. Includes high pressure
relief valve & 3-1/2" HB outlets with
Hydraulic Motor Mounting Flange Kits
individual shut-offs............................................... 157.00
HY 9910-GS50GI 48 725 9910-D813, -D1064, -D1265 & -1516
pumps. Remote unit includes high pressure relief
valve & (3) 1/2" HB outlets w/individual shut-offs.... 3 06.50
HY 9910-VDR50 35 725 9910-D503, -D813, -D1064, & -D1265 pumps.
Includes high pressure relief valve & (2) 1/2" HB
outlets with individual shut-offs............................ 370.50 No. 9910-HYD5312 No. 9910-HYD1570 No. 9910-HYD5341
HY 3300-0087 40 290 9910-D70 & -D115 pumps. Remote Unit includes Part No. Fits Diaphragm Pump Models
built-in relief valve & (3) 3/4", 1/2", & 3/8" HB HY 9910-HYD5312 9910-D30, 9910-D50, 9910-D303, 9910-D403,
outlets with individual shut-offs. . ........................ 334.50 9910-D503, 9910-D813, 9910-D1064 & 9910-D1265
HY 9910-BMH50 40 725 9910-DBS110, -140, -160 pumps........................ 309.00
HY 9910-GH50 50 725 9910-DBS200 pumps........................................... 275.50 HY 9910-HYD1570 9910-D160, 9910-D250
HY 9910-HYD2495 9910-D70 & 9910-D115
Part No. REMOTE MOUNTING KITS Net Ea.
HY 9910-KIT1741 Remote mounting kit for 9910-GS40GI unit..................... $ 37.30 Part No. HYD. MOTOR MTG. FLANGE KITS WT./Lbs. Net Ea.
HY 9910-KIT1742 Remote mounting kit for 9910-GS50GI unit..................... 64.65 HY 9910-HYD5312 Includes one flange, one 1" hollow
shaft and two bolts............................. 5.5 $ 152.50
HY 9910-HYD1570 Includes one flange, one coupling
and six bolts........................................ 2.5 195.00
HY 9910-HYD2495 Includes one flange, one coupling
and two pins....................................... 5.5 152.50
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0269
12-Volt Diaphragm & Roller Pumps 133
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0693
134 Electric Diaphragm Pumps • Controllers
SHURflo ShurFlo Pumps for a wide variety of low pressure applications. Pumps are available in 12/24/115V with
EPDM, Viton® or Santoprene internals. Adjustable demand switch for automatic shut-off or internal by-pass
DIAPHRAGM PUMPS without a switch. Maximum temperature is 170° F. Note: Pumps are not warranted for chemical compat-
ibility. Buna is the best choice for petroleum products.
12-VOLT/115-VOLT/24 VOLT
SLV10 Series
Capacities to 7.0 GPM • Pressures to 100 PSI Part No. SHURflo REPAIR KITS & Accessories Net Ea.
D SU 94-395-05 Diaphragm Kit, Viton®, for 8000 Series . ..... $ 40.70
#8000-543-250
SU 94-395-06 Diaphragm Kit, Santoprene, for 8000 Series. 13.35
SU 94-238-04 Diaphragm Kit, Santoprene, for 2088 Series. 24.70
SU 94-238-03 Diaphragm Kit, Santoprene, for 4111 & 4211 24.70
#4211-035
SU 94-232-00 Valve Kit, Santoprene, for 2088 Series.......... 12.95
D SU 94-232-05 Valve Kit, Viton®, for 2088, 4111 & 4211 Series 34.60
D SU 94-390-05 Valve Kit, Viton®, for 8000 Series ................ 29.70
SU 94-390-08 Valve Kit, EPDM, for 8000 Series.................. 16.20
SU 94-391-09 Valve Kit, Viton®, for 8000 By-Pass Series . 34.05
D SU 94-231-05 Switch Kit for 2088 Series............................. 38.70
SU 94-375-05 Switch Kit for 8000 Series ............................ 19.30
#8000-543-236 SU 94-230-40 Switch Kit for 4111 & 4211............................ 21.45
Many Other Models Available SU 255-323 1/2" HB x FPT 50 Mesh Inlet Strainer .......... 10.95
Polypropylene Straight
90° Elbow Part No. Net Ea.
SU 816201 1/2" FPT X 3/8" HB Straight . ................... $ .73
Swivel Fittings SU 816101 1/2" FPT X 1/2" HB Straight . ................... .73
SU 815901 1/2" FPT X 3/8" HB 90° Elbow ................. .73
with Wingnut for SU 815801 1/2" FPT X 1/2" HB 90° Elbow ................. .73
SU 815501 1/2" FPT X 5/8" HB 90° Elbow ................. .73
Hose & Tube on SU 815701 1/2" FPT X 3/4" HB 90° Elbow ................. .73
ShurFlo Pumps D D
SU 814501 1/2" MPT X 3/8" MPT Strainer Adapter . . .92
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0262
Electric Diaphragm Pumps 135
FloJet MOTOR DRIVEN DIAPHRAGM PUMPS Pumps are available in either 115 volt or 12 volt,
(230 and 24 volt on special request). Pumps are
available in two styles:
12-Volt/115-Volt • Capacities to 7 GPM • Pressures to 150 PSI Bypass Pump continues to run and
internally bypasses if discharge
These pumps are the perfect choice for chemical transfer, carpet cleaning, car/truck wash applications, livestock is partially or fully closed.
cooling and many more. Excellent self-priming capabilities and can be run dry. Diaphragms and check valves Demand Pressure switch automatically
are available in Buna, Santoprene®, EPDM and Viton® as noted. Available in either Demand or Bypass starts and stops pumps at
styles. (Note: Many models are available in addition to those shown below - Call for Pricing & Availability). specific pressure settings.
Demand Pumps are supplied with pressure actuated switches that provide on/off control within certain pressure ranges.
Bypass Pumps are designed to internally bypass when discharge is closed or partially closed.
D
Pumps with No Switches or Bypass
Max. Max.
Part No. Volts GPM PSI Internals Ports Net Ea.
R7300142A
FJ 2100-910 12 V 1.9 60 Buna 3/8" FPT $ 115.00
FJ D31X015F 12 V 2.0 50 Buna 3/8" FPT 96.60
Viton® is a registered trademark of DuPont Performance Elastomers - ®Santoprene is a registered trademark of Mansanto Co.
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0732
136 Air Operated Diaphragm Pumps
Air-Operated Diaphragm Pumps Yamada® Air Operated Diaphragm Pumps
GRACO Air-Operated Diaphragm Pumps. Designed for a wide Air-Powered, Double-Diaphragm
variety of chemicals, solutions, coatings, solvents or abrasives. Ideal Pumps. Ideal for pumping tire
for tough, viscous products. Air supply range is 25 - 100 PSI (125 chemicals in CTA units, wheel brite
PSI for 1” and larger). chemicals or bug cleaner products.
Unique, simple, safe. These pumps
Features: Polypropylene, Aluminum or Kynar Bodies with Buna, Hytrel, will handle practically anything that
Santoprene or Teflon diaphragms • Seal-less, leak-proof design prevents will flow. Multi-purpose pumps are
fluid waste or spills • Pumps can run dry without damage • Air drive means available for almost every plant in every
no electrical hazards • Lightweight and portable for multi-location use •
industry. Abrasive and corrosive fluids
Poly, Kynar and Aluminum pumps with Santoprene diaphragms are rated D
can be handled without problems.
to 180° F. and pumps with Teflon diaphragms are rated to 220° F. • Limited
number of parts means fast repairs.
Pulsation Dampeners
Available
Husky 1590 Series
1-1/2” Ports D
D 4.8mm Solids
(100 GPM) Model NDP-5FVT
Max. Part No. Ports Diaphragm GPM CAPACITY Wt. Net Ea.
Part No. Ports Pump Body Diaphragm Flow Net Ea. YA NDP-5FPT 1/4" FPT Teflon 3 @ 7 cfm air 3 lbs. $176.50
GY D12096 1/4" FPT Polypropylene Santoprene 5 GPM $ 188.55 YA NDP-5FVT * 1/4" FPT Teflon 3 @ 7 cfm air 3 lbs. 549.00
GY D12091 1/4" FPT Polypropylene Teflon 5 GPM 269.76 YA DP-10BPH 3/8" FPT Hytrel 5 @ 7 cfm air 5 lbs. 237.00
GY D150A1 1/4" FPT Kynar Teflon 5 GPM 345.35 YA DP-10BPSE † 3/8" FPT Santoprene 5 @ 7 cfm air 5 lbs. 236.00
GY D32966 3/8” FPT Polypropylene Santoprene 7 GPM 269.76 YA DP-10BPT 3/8" FPT Teflon 5 @ 7 cfm air 5 lbs. 265.00
GY D32955 3/8” FPT Polypropylene Hytrel 7 GPM 279.77 YA NDP-15FPH 1/2" FPT Hytrel 12 @ 12 cfm air 9 lbs. 312.00
GY D32911 3/8” FPT Polypropylene Teflon 7 GPM 348.84 YA NDP-15FPS † 1/2" FPT Santoprene 12 @ 12 cfm air 8 lbs. 289.00
GY D52966 1/2” FPT Polypropylene Santoprene 15 GPM 345.39 YA NDP-15FPT 1/2" FPT Teflon 12 @ 12 cfm air 8 lbs. 305.00
GY D52955 1/2” FPT Polypropylene Hytrel 15 GPM 371.74 YA NDP-15FVT * 1/2" FPT Teflon 12 @ 12 cfm air 8 lbs. 679.00
GY D52911 1/2” FPT Polypropylene Teflon 15 GPM 477.21 YA NDP-20BPC 3/4" FPT Neoprene 30 @ 30 cfm air 18 lbs. 529.00
GY D45A11 1/2” FPT Kynar Teflon 15 GPM 719.68 YA NDP-20BPH 3/4" FPT Hytrel 30 @ 30 cfm air 18 lbs. 529.00
GY D53277 3/4” FPT Aluminum Buna 16 GPM 386.98 YA NDP-20BPT 3/4" FPT Teflon 30 @ 30 cfm air 18 lbs. 597.00
GY D53366 3/4” FPT Aluminum Santoprene 16 GPM 402.92 YA NDP-20BAN ** 3/4" FPT Buna 30 @ 30 cfm air 18 lbs. 459.00
GY D53211 3/4” FPT Aluminum Teflon/EPDM 16 GPM 473.74 YA NDP-25BAH ** 1" FPT Hytrel 42 @ 50 cfm air 27 lbs. 539.00
GY 647074 1” FPT Aluminum Buna 50 GPM 633.82 YA NDP-25BPC 1" FPT Neoprene 42 @ 50 cfm air 27 lbs. 659.00
GY 647035 1” FPT Aluminum Santoprene 50 GPM 575.56 YA NDP-25BPH 1" FPT Hytrel 42 @ 50 cfm air 27 lbs. 659.00
GY 647075 1” FPT Aluminum Teflon/EPDM 50 GPM 691.09 YA NDP-25BPT 1" FPT Teflon 42 @ 50 cfm air 27 lbs. 729.00
GY 649029 1” ANSI Flange Polypropylene Santoprene 50 GPM 726.75 YA NDP-25BAN ** 1” FPT Buna 42 @ 50 cfm air 27 lbs. 539.00
GY 649034 1” ANSI Flange Polypropylene Teflon 50 GPM 824.91 YA NDP-40BAN **1-1/2" FPT Buna 100 @ 90 cfm air 68 lbs. 729.00
GY 649038 1” ANSI Flange Kynar Teflon 50 GPM 903.55 YA NDP-40BAS **1-1/2" FPT Santoprene 100 @ 90 cfm air 68 lbs. 698.00
GY DB2911 1-1/2” Flange Polypropylene Teflon 100 GPM 1846.69 YA NDP-40BPN 1-1/2" Flange Buna 100 @ 90 cfm air 68 lbs. 1349.00
GY DB2966 1-1/2” Flange Polypropylene Santoprene 100 GPM 1683.52 YA NDP-40BPT 1-1/2" Flange Teflon 100 @ 90 cfm air 68 lbs. 1629.00
GY DB5A11 1-1/2” Flange Kynar Teflon 100 GPM 3593.59 YA NDP-50BAN ** 2" FPT Buna 150 @ 180 cfm air 88 lbs. 869.00
GY DB3777 1-1/2” FPT Aluminum Buna 100 GPM 697.67 YA NDP-50BAT ** 2" FPT Teflon 150 @ 180 cfm air 88 lbs. 1375.00
GY DF2911 2” Flange Polypropylene Teflon 150 GPM 2652.61 YA NDP-50BPT 2" Flange Teflon 150 @ 180 cfm air 88 lbs. 2319.00
GY DF2966 2” Flange Polypropylene Santoprene 150 GPM 2462.46 * Standard with Kynar body.
** Standard with Aluminum body.
GY DF5A11 2” Flange Kynar Teflon 150 GPM 5455.31
GY DF3777 2” Flange Aluminum Buna 150 GPM 895.83 † Best Choice where shutoffs such as solenoids are used.
GY DK3666 3” Flange Aluminum Santoprene 275 GPM 1941.88 Note: Above Pumps should always have a filter/regulator on the air supply line.
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0260
Air Operated Diaphragm Pumps 137
SandPiper Air-Driven Diaphragm Pumps from Warren Rupp. “No-Stall” design for continuous operation. Ideal for abrasives, caustics, corrosives
and viscous chemical transfer. Pumps can run dry without damage. Air drive means no motors or engines are required. ISO Certified. Inlet supply
pressure is 20 to 100 PSI on plastic pumps and 20 to 125 PSI on metal pumps. Maximum discharge pressure is 100 PSI. Maximum viscosity
is 10,000 SSU or 2200 CPS. Maximum temperatures to 150° F.
Pumps are available in a variety of sizes and construction to meet your needs. Other pump configurations and sizes are available in addition
to those shown.
Air-Driven Diaphragm Pumps
PLASTIC BODIES
Part No. Ports Body Diaphragm Max. Flow Wt. Net Ea.
SO TS3PP 1/4” Polypropylene Santoprene 4 GPM 4 lbs. $ 186.54
SO TT3PP 1/4” Polypropylene Teflon 4 GPM 4 lbs. 245.06
SO TT3K 1/4” Kynar Teflon 4 GPM 4 lbs. 269.58
SO 5PPB 1/2” Polypropylene Buna 14 GPM 16 lbs. 359.09
SO 5PPS 1/2” Polypropylene Santoprene 14 GPM 16 lbs. 399.61
SO 5PPT 1/2” Polypropylene Teflon 14 GPM 16 lbs. 456.11
SO 5PPK 1/2” Kynar Teflon 14 GPM 16 lbs. 715.17
SO 7B1P1 3/4” Polypropylene Santoprene 23 GPM 17 lbs. 549.14
SO 7B1P2 3/4” Polypropylene Teflon 23 GPM 17 lbs. 699.18
SO 1FB2P3 1” Polypropylene Buna 45 GPM 53 lbs. 869.21
SO 1FB2P1 1” Polypropylene Santoprene 45 GPM 53 lbs. 868.73
SO 1FB2P2 1” Polypropylene Teflon 45 GPM 53 lbs. 1058.78 D
SO 1FB2PK 1” Kynar Teflon 45 GPM 53 lbs. 1575.37
SO S15B33 1-1/2” Polypropylene Buna 100 GPM 105 lbs. 1698.40
SO S15B31 1-1/2” Polypropylene Santoprene 100 GPM 105 lbs. 1698.40
SO S15B32 1-1/2” Polypropylene Teflon 100 GPM 105 lbs. 2095.62
D SO S20B3 2” Polypropylene Buna 150 GPM 117 lbs. 2450.64
SO S20B1 2” Polypropylene Santoprene 150 GPM 117 lbs. 2475.68 Removable Air Valves
SO S20B2 2” Polypropylene Teflon 150 GPM 117 lbs. 2850.77
METAL BODIES
Part No. Ports Body Diaphragm Max. Flow Wt. Net Ea.
Polypropylene or SO S05BAB 1/2” Aluminum Buna 15 GPM 15 lbs. $ 515.14
Kynar Housings SO S05BAS 1/2” Aluminum Santoprene 15 GPM 15 lbs. 515.14
SO S05BAT 1/2” Aluminum Teflon 15 GPM 15 lbs. 695.17
SO SS5BS1 1/2” Stainless Santoprene 15 GPM 21 lbs. 1123.32
SO SS5BS2 1/2” Stainless Teflon 15 GPM 21 lbs. 1247.32
SO S1FBAB 1” Aluminum Buna 45 GPM 28 lbs. 635.18
SO S1FBAS 1” Aluminum Santoprene 45 GPM 28 lbs. 635.18
SO S1FBAT 1” Aluminum Teflon 45 GPM 28 lbs. 829.18
SO SBSS1W 1” Stainless Santoprene 45 GPM 43 lbs. 1325.36
SO SBSS2T 1” Stainless Teflon 45 GPM 43 lbs. 1476.38
SO S15B1AB 1-1/2” Aluminum Buna 106 GPM 53 lbs. 825.18
SO S15B1A1 1-1/2” Aluminum Santoprene 106 GPM 53 lbs. 825.18
SO S15B1A2 1-1/2” Aluminum Teflon 106 GPM 53 lbs. 1198.34
SO S15B1S1 1-1/2” Stainless Santoprene 106 GPM 95 lbs. 2398.54
SO S15B1S2 1-1/2” Stainless Teflon 106 GPM 95 lbs. 2498.62 D
SO S20B1AB 2” Aluminum Buna 150 GPM 77 lbs. 1198.28
SO S20B1A1 2” Aluminum Santoprene 150 GPM 77 lbs. 1198.28
SO S20B1A2 2” Aluminum Teflon 150 GPM 77 lbs. 1570.40
SO S20B1S1 2” Stainless Santoprene 150 GPM 120 lbs. 3275.77
SO S20B1S2 2” Stainless Teflon 150 GPM 120 lbs. 3976.05 Metal Housing
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0261
138 Air Operated Diaphragm Pumps
FLOJET Air Driven Diaphragm Pump
Air Operated Pump Ideal for use with Tire Cleaner or
Bug Cleaner Products in Tunnel
or Rollover installations. Air Drive
Ideal for tire cleaners, bug cleaners,
design allows for easy hook-up.
foam brush solutions, presoak
Self-priming style with automatic
chemicals, acid products and D
shut-off. Maximum flow is 2.5
many more. D
GPM. Maximum inlet temperature
Two-chamber, dual diaphragm is 120° F. Maximum pressure is
design. Powered by compressed 80 PSI.
air, CO2 gas or nitrogen.
Temperature range is +34° F. to Standard Features Include: Infinitely variable capacity from zero to
+120° F. maximum flow. • Automatic demand operates pump only when discharge
Size is 7" x 6" x 4". Inlet and outlet fittings valve or gun is open, stops instantly when valve is closed. • Pump can
are 3/8" SS hose barbs. Air inlet fitting is 1/4" run dry without causing damage. • Liquid being pumped does not come in
nylon hose barb. contact with any metal parts. • No electrical connections. • No pressure relief
valve or bypass plumbing is required. • Santoprene Elastomers for added
Suction lift (wet) is 25 in/hg. Pumping distance will vary with viscosity. Maximum chemical resistance. • Acetal/Celcon body • Air Ports are 1/4” Barb.
flow is 2.20 GPM @ 20 PSI discharge & 60 PSI air inlet. Polypropylene
body, 316SS internals and Viton® or EPDM diaphragms are standard for Air Fluid
added chemical compatibility. Part No. Diaphragm/Valves Ports Ports Net Ea.
FJ 5100-040 Santoprene 1/4" Barb 3/8" Barb $ 70.20
FJ 5100-020 Viton® 1/4" Barb 3/8" Barb 79.75
Part No. Diaphragms *Flow @ 30 PSI Fluid Ports Wt. Net Ea.
FJ 5100-050 Geolast* 1/4" Barb 3/8" Barb 74.70
SU 166-20036 VITON® 1.75 gpm 3/8" 2 lbs. $ 111.50
FJ 20466-003 Santoprene Diaphragm Kit, pumps prior to 2008 11.85
SU 166-20056 EPDM 1.75 gpm 3/8" 2 lbs. 85.95 FJ 20467-003 Santoprene Valve Kit, pumps prior to 2008 ....... 14.80
SU 94-175-06 EPDM Diaphragm & Valve Kit.................................... 13.10 FJ 20466-002 Viton® Diaphragm Kit, pumps prior to 2008 . .... 27.20
SU 94-175-05 Viton® Diaphragm & Valve Kit................................... 51.70 FJ 20467-002 Viton® Valve Kit, pumps prior to 2008 . ............. 18.20
SU 94-175-07 Santoprene Diaphragm & Valve Kit ......................... 11.80 GN 6ZC63 Air Filter - 1/4" M x 1/4" F (Pkg. of 2)................. 20.05
* Based on 60 psi inlet pressure. * Geolast is best for petroleum base products.
NOTE: Viton & Santoprene Kits are no longer interchangeable on pumps.
MODEL
Part No. Elastomers Max. PSI Wt. Net Ea. G257
SU 477-40001 Santoprene 100 2.5 lbs. $ 106.50 Air
Pump
Flow Rate
GPM (L/min)
*Indicates Air
Inlet Pressure
Visit Our Online Store Part No. Diaphragm Max Flow *Max PSI Net Ea.
Anytime. Anywhere. FJ G5700 Santoprene** 7 GPM 100 $ 84.95
FJ G5700V Viton® 7 GPM 100 121.50
dultmeier.com FJ G5700C † Kalrez 7 GPM 100 175.50
FJ G257501A Santoprene** 10 GPM 100 207.00
FJ G257301A Viton® 10 GPM 100 250.00
FJ 20730-000A Diaphragm Kit, Santoprene**............ 16.65
FJ 20740-050A Check Valve Kit, Santoprene**.......... 11.10
FJ 21000-209 Diaphragm Kit, Viton®....................... 29.75
FJ 20740-020A Check Valve Kit, Viton® .................... 40.50
* Maximum air consumption is 2.8 cfm @ 120 psi.
† Higher chemical resistance than Viton® or Santoprene.
Viton® is a registered trademark of DuPont Performance Elastomers ** Santoprene is a registered trademark of Monsanto Co.
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0264
Gear & Progressive Cavity Pumps 139
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0729
140 Gear & Piston Pump Units
Viscous Products & Liquid Feed
Pump Units
Use these Pump Units for Oils, Liquid Feeds and Other Viscous
Products (Non-Abrasive) up to 100,000 SSU.
2835 PERFORMANCE
1800 RPM 1200 RPM
PSI SSU 100 1000 10,000 100,000 100 1000 10,000 100,000
25 GPM 11 11.4 11.5 11.5 7.2 7.5 7.6 7.6
HP .28 .40 .63 1.18 .15 .22 .32 .57
75 GPM 10 11.2 11.3 11.4 6.1 7.3 7.4 7.5
HP .60 .72 .95 1.5 .39 .46 .56 .81 2835
Roper's 2835 rotary pump is designed for use in the pumping of viscous
products and molasses base feed supplements. Capacities range up to 11
GPM at 1800 RPM. Teflon-Viton® lip seal is standard.
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0241
GEAR PUMPS 141
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0244
142 Gear Pumps & Pump Units
LONG-LASTING WEARING SURFACES
Packed box seal, top
& side ports, with
• Bearings are special wear-resistant, high-lead bronze. Iron
relief valve.
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0242
Gear Pumps & Parts 143
Roper Pump
Repair Kits
Featuring “Genuine” Roper Parts!!
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0243
144 Injection Metering Pumps & Valves
Irrigation Injection Injection Check Valves
Chemical Injection Metering Pumps Injection Check Valves allow chemicals to be injected into the turbulent flow near
the center of the line, providing more uniform dispersion. The disk type check and
E-Z Meter Pumps are designed seat are located at the tip of the check valve to allow constant flushing.
to inject a wide variety of SSQ75
chemical prod- Stainless
ucts at pressures
up to 150 psi. PPQ50
Injection ranges Poly
from 1.6 to 470
Mounting FEATURES
GPH (gallons per
Mounts directly to a coupling • Provides Back Pressure to Insure Metering
hour.) All wetted in the sidewall of lines 6 inches Accuracy.
D
parts are 316SS and larger. For smaller lines the • Prevents Back Flow.
or chemically resis- check valve may be mounted to a
coupling attached to a nipple (of • Prevents Bleed Through When Water
tant polypropylene. Pressure is Low or Line is Drained.
the length required), to hold the tip
(Teflon also available • Prevents Siphoning When Metering Pumps
of the check valve near the center
for acid applications). Also features double ball built-in check valves and of the line. are Off and Line is Flowing.
replaceable piston cups.
Specifications: 3/4” NPT Line Connection • Check Material is Viton® •
Pumps are easily maintained and serviced. Injection rates can be changed Spring Material is 316SS • Maximum Pressure is 150 PSI.
by a simple change of the stroke on the piston. Pumps are available in a
single piston design or in a double pump design for higher capacities or for Injection Check Valves: Inlet Flow† Max.
injecting 2 different products or 2 injection rates. Part No. Material Size GPH Temp. Net Ea.
CX PPQ50 Polypropylene 1/4” 50 120° F. $ 22.80
Pump drives are available in 1 Phase or 3 Phase electric motors, gas engine, CX SSQ75 Stainless 1/2” 200 150° F. 96.00
12 Volt or belt/pulley drive where you supply the power source. 1 Phase † At 50 PSI Differential. 5% on 12 Units & 10% on 25 Units.
motors are 110-220 Volt, 3 Phase motors are 220-440 Volt.
The bleeder valve from Agri-Inject is versatile and simple - and is the perfect
Simplex Single Piston Units complement to the Mister Mist'r® injection check valve. Put the two together to create
an unbeatable assembly for controlling and adjusting your chemigation system - or
Part No. GPH Drive Design Wt. Net Ea.
use the bleeder valve alone for small-scale irrigation in nurseries or greenhouses.
BU 10620 5-30 1/2 hp, 1 phase............. 68 lbs. $ 1065.00
BU 20620 5-30 1/2 hp, 3 phase............. 68 lbs. 1020.00 Bleeder Valves:
BU 01620 5-30 Pulley Drive - No motor. 50 lbs. 1102.00 Part No. Body Inlet Outlet Net Ea.
BU 11630 10-100 1/2 hp, 1 phase............. 68 lbs. 1691.00 CX MMBP Poly 1/4" FPT 1/4" MPT $ 11.50
BU 21630 10-100 1/2 hp, 3 phase............. 68 lbs. 1392.00
BU 01630 10-100 Pulley Drive - No motor. 50 lbs. 1289.00
D
The VRH-1000 Variable Rate Control System works with any John Blue piston or
squeeze pump for ground speed oriented & variable rate control from the cab. Also
works with many GPS/GIS control systems including Ag Leader, Agco Field Star &
John Deere Green Star. Includes Rawson Accu-Rate controller, hydraulic motor drive
kit, sprockets/chain, wiring harness & pump base plate (hydraulic hoses not included).
Use with John Blue flow divider (without orifice discs) for much wider application range.
D
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0251
Ground Drive Pumps & Accessories 145
NGP Piston Pumps NGP — Completely Redesigned . . . The Best Just Got Better
The NGP Piston Pumps give the grower the most modern engineering design and technology available. The NGP offers excellent
enhancements, plus all the features and benefits of the proven “LM” pumps growers have successfully used for many years.
Features:
• New single valve cap making it easier to service in the field.
• New check valve design with o-ring enhances priming and is more forgiving with debris and has better accuracy.
• Simple to inspect plunger packing without removing hoses; New 3 stage universal piston rod seals.
• Standard main shafts across the entire NGP line, all clutches fit all models.
D • Newly designed setting wrench that is universal for all models.
• Footprints are the same as LM Series Pumps; Variable Rate Ready. See adjacent pages for variable rate controls.
• Also available with stainless wet ends.
NGP PUMP REPAIR KITS
GPM @ Max. Wt.
Gasket Suction Discharge
Part No. 450 RPM PSI Ports Clutch Lbs. Net Ea. Pump Repair Valve Valve Operators
BU NGP6055 Single Piston, Low Volume 21.0 120 1-1/2” None 62 $ 1183.54 Model Kit Assembly Assembly Kit
BU NGP7055 Single Piston, High Volume 34.2 120 1-1/2” None 93 1359.02
NGP6055 115788 115706-91 115707-91 BU115787
BU NGP8055 Dual Piston, Low Volume 42.0 120 1-1/2” None 125 2049.00
BU NGP9055 Dual Piston, High Volume 68.4 120 1-1/2” None 155 2035.49 NGP7055 115688 115606-91 115607-91 BU115787
BU 115670 Rope Pull Clutch............................................................................................. 403.50 NGP8055 115789 115706-91 115707-91 BU115787
BU 115671 Hydraulic Clutch............................................................................................. 484.00 NGP9055 115689 115606-91 115607-91 BU115787
BU 115672 12 Volt Clutch.................................................................................................. 614.00
CDS John Blue LM Ground Drive Piston Pumps are variable stroke metering pumps, specifically
designed to accurately meter liquid fertilizer solutions. Cast iron bodies with 316 SS internals with
D
components subject to abrasion hard chrome plated. Positive displacement, chain driven design operates
in direct and immediate relation to ground speed. The output rate can be set before application begins
and the GPA application will remain accurate regardless of speed changes. Orifice discs not required
with these pumps.
LM1255 Series
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0249
146 Squeeze Pumps & Accessories
The John Blue ground driven metering pump accurately maintains the same rate of application per acre at all ground speeds. Whether
you speed up or slow down due to terrain or soil conditions, the application rate will not vary. A true metering pump will also maintain
a constant rate at any fluid level in the tank. The John Blue squeeze pump has met these demands and surpassed them.
Features:
• Heavy cast iron, rigid frame will not flex due to uneven ground.
• Grease fittings on rollers allow dirt and fertilizer contamination to be flushed out.
• Round hoses and spring loaded back plate. No. L6C
• Hoses have memory shape for accurate rates.
• Positive shut off when pump stops.
• Your choice of individual sprockets or complete cluster sets.
D
• Wide range of available sprockets allows for 87 different application rates. D
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0250
Plunger Pumps 147
Plunger Pumps from PumpTec can be used in a wide variety of spraying applications including: Carpet Cleaning, Pest Control, Turf Spraying,
Misting and Reverse Osmosis Systems. Available with 12, 120 or 230 volt motors. Sold in pump/motor combinations or as replacement pumps
and repair parts. Regulators, repair kits and misting nozzles are also available.
Model 356U
Model 114
Model 356U Pumps feature aluminum
114 Series bodies with stainless steel plungers D
Model 114 Pumps feature and valves. Seals are Viton® or Buna.
Grilon Plastic bodies with Acetal Rated to 1200 PSI and 140° F. Ports
valves, stainless plungers and are 3/8” FPT inlet and outlet.
D
Buna (V) or Viton® (T) seals.
Rated to 200 PSI and 140° F. GPM Maximum Amp
Inlet ports are 1/2” hose barb, Part No. Volts Flow PSI Draw Seals Wt. Net Ea.
3/8” MPT. Outlet ports are 1/4” PX 356U-200/M64 120V 1.50 1000 11.5 Buna 48 lbs. $ 434.00
MPT. PX 356-M26 12V 2.19 300 61 Viton® 45 lbs. 478.00
PX 356-M96 12V 2.50/2.0 250/450 44/66 Viton® 47 lbs. 667.00
PX 356U Pump Only 2.9 450 - Buna 6.5 lbs. 222.00
GPM Maximum Amp
Part No. Volts Flow PSI Draw Seals Wt. Net Ea.
PX 114T-M35 120V .89 200 1.4 Buna 10 lbs. $ 176.50
PX 114T-075/M15 12V 1.50 200 15 Viton® 10 lbs. 171.50
PX 114T Pump Only 1.50 200 - Viton® 2.5 lbs. 95.95 REPAIR KITS
Part No. Kit Description Net Ea.
Model 205V PX 112KITA
PX 112KITA-V
Plunger/Seal Kit, 112/114, Buna................... $ 43.20
Plunger/Seal Kit, 112/114 , Viton®................ 46.95
PX 10034 Plunger/Seal Kit, 113, Buna.......................... 79.95
PX 204KITA Plunger/Seal Kit, 204/205/207, Buna............ 47.95
Model 205V Pumps feature
PX 348KITA Plunger/Seal Kit, 348U, Buna........................ 75.20
aluminum bodies with stainless
PX 10007 Plunger/Seal Kit, 356U, Buna........................ 73.60
steel plungers and valves and
PX 112KITB P Valve Kit, 112, Buna................................... 24.00
Buna seals. Rated to 800 PSI
PX 10018 P Valve Kit, 112, Viton®................................. 25.60
and 140° F. Ports are 3/8” FPT
PX 10004 M Valve Kit, 112/113/348/356, Buna............. 27.20
inlet and outlet.
PX 10014 U Valve Kit, 114, , Buna................................. 16.00
D PX 10037 Q Valve Kit, 114, Buna................................... 16.00
PX 10041 G Valve Kit, 114, Viton®................................ 19.20
PX 204KITB A Valve Kit, 204V, Buna ................................ 43.20
GPM Maximum Amp PX 10022 M Valve Kit, 205V/207, Buna......................... 30.40
Part No. Volts Flow PSI Draw Seals Wt. Net Ea.
PX 212KITB S Valve Kit, 212, Viton®................................. 25.60
PX 205V-110/M18 120V .90 800 7.2 Buna 29 lbs. $ 349.00
PX 205V-125/M77 120V 1.10 500 3.5 Buna 30 lbs. 406.00 PX 10010 S Valve Kit, 348/356, Buna............................ 24.00
PX 205V Pump Only 1.60 800 - Buna 5.5 lbs. 183.00 PX 10016 H Valve Kit, 348/356/357, Viton®.................. 25.60
Viton® is a registered trademark of DuPont Performance Elastomers
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0263
148 Rotary Vane Pumps
Procon and Rotoflow
Positive Displacement Rotary Vane Pumps: An excellent choice for handling clean fluids such as tire cleaners, presoak chemicals,
spot-free RO water, foam brush solutions, oils, syrups, inks, dyes, acids, etc. Unique design handles liquids with low lubricating
characteristics at relatively high pressures. Pumps should be protected from matter larger than 125 microns.
Pump Characteristics: Viton® sealing parts for added chemical resistance (1300/1500/1600 & PO300 series) • Replaceable brass
or stainless housings • Self-priming • Three-bearing design for pulley or direct drive • Carbon graphite internal vanes, bearings and
liner provide no metal to metal contact for long life and quiet operation • Available with relief valves to protect against over pressure
(1300/1500/1600 & PO300 series) • Mounting flanges for direct mounting to C-face motors or V-band mounting for “carbonator”
motors with “y” frames • Maximum temperature is 150° F. (190° with special seals). Maximum viscosity is 500SSU.
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0265
Sump • Specialty • Magnetic Drive Pumps 149
Model 9S-CIM: Manual pump rated to 110 gpm @ 10' height, (30 Model 14S-CIM: Manual pump rated to 100 gpm @ 10'
gpm @ 15' height). Shut-off height is 20'. Motor is 4/10 hp , 115 height. Shut-off is 25'. Motor is 1/2 hp, 115 volt with 20'
volt motor with 20' power cord. Discharge port is 2" FPT. Handles power cord. Discharge port is 3" FPT. Handles solids to
solids to 2". Dimensions: 11-1/2" H x 11-1/2" L x 7" W. Weight 35 lbs. D 2". Standard with cast iron impeller. Dimensions: 17-3/16"
D
H x 14-1/16" L x 9-7/8" W. Weight 80 lbs.
Model 9S-CIARFS: Same as above but with remote automatic
float switch for “on” at 9-14", off at 2-5".
Model 10S-CIM: Manual pump rated to 120 gpm @ 5' height, Model 16S-CIM: Manual pump rated to 160 gpm @
(70 gpm @ 15' height). Shut-off height is 25'. Motor is 1/2 hp, 115 10' height. Shut-off is 35'. Motor is 1 hp,
volt with 20' power cord. Discharge port is 2" FPT. Handles solids to 9S-CIM 10S-CIARFS 230 volt with 20' power cord. Discharge
2". Dimensions: 11-1/2" H x 11-1/2" L x 7" W. Weight 36 lbs. port is 3" FPT. Handles solids to 2".
Standard with cast iron impeller. Dimensions: 17-3/16" H x 14-1/16" L
Model 10S-CIARFS: Same as above but with remote automatic float switch for “on” at x 9-7/8" W. Weight 88 lbs.
9-14", off at 2-6" liquid level.
Model 10SH-CIARFS: Same as above but with remote automatic float switch for “on” at
9-14”, off at 2-6” liquid level.
Model 20S-CIM: Manual pump rated to 205 gpm @ 10'
Maximum Automatic height. Shut-off is 75'. Motor is 2 hp, 1 ph, 230 volt with D
Part No Motor Flow Switch Net Ea. 20' power cord. Discharge port is 3" FPT. Handles solids
GJ 9S-CIM 4/10hp-115v 110 gpm @ 5’ No $ 257.46 to 2". Standard with brass impeller. Dimensions: 19-1/8"
GJ 9S-CIARFS 4/10hp-115v 110 gpm @ 5’ Yes 278.65 H x 12-7/8" H x 7-5/8" W. Weight 96 lbs.
GJ 10S-CIM 1/2hp-115v 120 gpm @ 5’ No 298.81 14S-CIM
GJ 10S-CIARFS 1/2hp-115v 120 gpm @ 5’ Yes 317.27
GJ 14S-CIM 1/2hp-115v 100 gpm @ 10’ No 539.22
Check pump components for compatibility if
GJ 16S-CIM 1hp-230v 160 gpm @ 10’ No 683.43 chemical solutions are to be removed.
GJ 20S-CIM 2hp-230v 205 gpm @ 10’ No 867.81
Specialty Pumps
These pumps are ideal for light volume transferring or
Submersible Parts Washer Pump recirculating of chemical solutions. Specifically engineered
for highly specialized applications. Submersible and Non-
Little Giant Brand. For use with Stoddard submersible models.
Solvent and deodorized Kerosene. Cast
aluminum housing, Viton® seal & nylon D
Model NK1 Submersible pump designed for use in mild acids,
head. Thermally protected. Outlet is NK1 alkalies and hard water applications. Perfect choice for automatic
1/4" MPT. Supplied with a 6 ft. 3 soap tank applications.
conductor cord with a 1/2" Features: Glass-filled, corrosion resistant, nylon housing • Viton® seal • 1/4" MPT
MPT builders fitting at cord discharge • 6' power cord • Hermetically sealed and filled with special oil for lifetime
outlet for conduit connection. D lubrication • Thermally protected. Dimensions are 4-9/16" x 4-1/8".
Handles unheated liquids Model 2E-NDVR: Non-Submersible pump for use with weak acids, chemicals, cleaning
up to 100° F. with a minimum solvents, anti-freeze, potable fluids (pH of 6-7).
140° flash point. Solutions Features: Nylon front with 3/8" FPT inlet, 1/4" MPT outlet • Stainless steel plate and motor
must be compatible with pump shaft • Viton® seals • 6' power cord • Thermally protected. Dimensions are 4-1/2" H x
materials. Flow rate is 205 GPH at 1' head. 4-1/4" x Model 1YS 5-1/2" L x 3-1/2" W.
4-1/8". Entire pump must be submerged.
Part No. * Flow Rate HP Voltage Wt Net Ea.
Part No. Power Wt. Net Ea. GJ NK1 210 GPH 1/150 115 Volt 3.4 lbs. $ 76.02
GJ 1YS Washer Pump 115-Volt 3 lbs. $ 91.92 GJ 2E-NDVR 300 GPH 1/40 115 Volt 5.4 lbs. 127.60
* Flow rates are based on 1' discharge height.
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0255
150 Submersible • Sump • Effluent Pumps
Little Giant Effluent Sump Pumps are designed for pumping dirty water with solids handling capabilities up to 3/4" diameter.
Completely submersible design. Applications include • De-watering • Construction sites • Sewer/Septic lines • Fountains/waterfalls
• Elevator Pits, Car Wash Pits and many more.
Standard Features Include: Cast Iron pump housings with Epoxy coating for added corrosion resistance • Oil-filled motor housings
for lifetime lubrication • Thermal overload protection • All motors are single phase, (three available on some models) • All pumps
are UL/CSA approved.
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0256
Cast Iron Submersible/Sump Pumps 151
5MSP
Submersible Pumps
D
No. 2P547 Submersible Pumps are
designed to pump either clear water or
effluent. Can be used in elevator pits, home
sumps, loading docks, or in other areas
where conventional sump pumps would
clog or freeze up due to the accumulation of
Model 5MSP: Manual pump with flow rates to 20 gpm, (14 gpm @ 15' D light debris. Unique vertical-path float switch
allows pumps to be mounted in narrow pits
height). Shut-off height is 26'. Standard with Viton® seal. Motor is 1/6 hp,
(12" minimum width).
115 volt with 18' power cord. 5 amp draw at startup. Discharge port is 1"
FPT. Dimensions: 7-3/4" H x 6-1/16" L x 4-5/16" W. Cast aluminum housing. Snap-Action Switch automatically turns
Weight 9 lbs. pump on and off at preset fluid depths.
Maximum fluid temperature 130° F. On at
Model 5ASP-FS: Same as above but with remote float switch for “on” at 7-1/2" - off at 3".
11" and off at 3". Power cord is 10'. Features: Non clogging screenless suction inlet • Non clogging vortex impeller
to pass up to 5/8" solids • Cast Iron housing & top • Impeller & base made of
Model 6CIM-R: Manual pump with flow rates to 45 gpm, (12 gpm at 15' Polypropylene • Mechanical seal with corrosion-resistant and stainless steel hardware,
height). Shut-off height is 17'. Motor is 1/3 hp, 115 volt with 25' power cord. Buna-N and carbon/ceramic parts • 43 GPM at 5' head • 19-1/4 ft. shut-off.
13 amp draw at startup. Discharge port is 1-1/2" FPT. Dimensions: 7-1/4" H 1-1/2" NPT discharge.
x 9-1/4" L x 7-1/4" W. Weight 18 lbs.
Housing Impeller Volts Dimensions
Model 6CIA-RFS: Same as above but with remote float switch for “on” at No. & Top & Base HP @ 60 Hz. Amps RPM Height Width
7-10" and off at 1-4". Standard with 10' power cord. 2P547 Cast-Iron Polypropylene 3/10 115 8.0 1550 9-3/4" 10-1/4"
Model 6CIA: Same as above but with an attached float switch. Dimensions: Part No. Wt. Net Ea.
6" H x 9-1/2" L x 8-1/2" W. GN 2P547 Submersible Pump..... 22 lbs. $ 197.00
Model 8-CIA: Same as above but with “Port a Pump” 12-Volt DC Sump Pump from
attached float switch for “on” at 7-10” and Warren Rupp. This handy dirty water pump can be
off at 1-4”. D
operated from any 12-volt car or truck battery. Ideal
for use when no other power source is available.
Rated to a maximum of 43 GPM at 5' discharge D
or 21 GPM at 20' discharge height.
Discharge port is 1-1/2"
NOTE: Check pump compatibility if
FPT. 30 Amp draw.
chemical solutions are to be removed
Standard with 30'
Part No. Motor Max. Flow Auto Switch Wt. Net Ea. cable and clamps.
GJ 5MSP 1/6hp-115v 20 gpm No 9 lbs. $ 102.74 Fits 10" openings.
GJ 5ASP-FS 1/6hp-115v 20 gpm Yes 9 lbs. 137.21 Pump dimensions:
GJ 6CIM-R 1/3-115v 46 gpm No 18 lbs. 129.90 10" Diameter x
19-1/4" H. Model SPA12E
GJ 6CIA-RFS 1/3-115v 46 gpm Yes 18 lbs. 142.52
GJ 6CIA 1/3-115v 46 gpm Yes 18 lbs. 129.80
Part No. Wt. Net Ea.
GJ 8-CIM 4/10-115v 54 gpm No 19 lbs. 206.50
SO SPA12E 12-Volt Sump Pump 37 lbs. $ 859.26
GJ 8-CIA 4/10-115v 54 gpm Yes 19 lbs. 239.50
Viton® is a registered trademark of DuPont Performance Elastomers
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0257
152 Stainless Submersible/Sump Pumps
Optima Stainless Steel Sump Pumps are an excellent choice for pumping dirty water, semi-dirty water or slurries. Also a good choice for
commercial or industrial seepage and effluent. Not for chemical use.
Standard Features Include: 3/8" solids handling capability • Rated for continuous duty applications • 304L stainless with high quality corrosion-resistant
material • Can be operated whether fully or partially submerged • Built-in thermal protection with automatic reset, (1-phase only) • ISO 2548 Rating • UL/CSA
Water resistant cords • Manual or Automatic shut-off • 13" Float switch with cord on 1/3 HP and 24" on 1/2 and 1 HP models.
EPPD 1/3 HP pumps feature double BUNA seals (oil bath mechanical seal bottom; lip seal top) and Noryl impellers Stainless
Steel!
EPD 1/2 HP and 1 HP pumps feature mechanical seals with Viton elastomers for added chemical resistance.
These models are standard with Stainless impellers. Optima EPPD-3AS1
Designed to handle up to 3/8" solids. Available in 1/3 & 1/2 hp, single phase or 1 hp, three phase models. Cords: Series
20' long on 1/3 hp, 1 hp, 1-1/2 hp and 10' on 1/2 hp. Maximum Temperature: to 120° F. continuous or 140° F.
intermittent duty. Ports: 1/3 hp units have 1-1/4" FPT ports, 1/2 hp, 1 hp and 1-1/2 hp have 1-1/2" FPT ports.
Dominator Stainless Steel Sewage Pumps. An excellent choice when effluents, sewage and larger solid handling is required.
• Oil-lubricated double mechanical seals with Viton® elastomers • 2" Solids handling capability • Rated for continuous duty • 304
stainless with high quality corrosion-resistant materials • Permanent split capacitor motors good for 20 starts per hour • Built-in thermal
protection on single phase models • ISO2548 Rating • 25' UL/CSA Water resistant cords • Manual or Automatic shut-off • Operates
fully or partially submerged.
The ideal choice for pumping industrial, agricultural or commercial waste water with suspended solids up to 2" diameter. Available in
1/2 hp through 2 hp sizes in single or three phase. Standard with 25' cords. Rated to 105° F. continuous or 140° F. intermittent duty.
Ports are 2" FPT.
Shut-off Dimensions
Part No. *Motor **Max. Flow Control Height (Dia. x H) Wt. Net Ea.
EA AU64S 1/2hp, 115v,1ph † 100 gpm @ 10' Automatic 21' 9" x 21-5/8" 36 lbs. $ 658.00
EA U64S 1/2hp, 115v,1ph † 100 gpm @ 10' Manual 21' 9" x 21-5/8" 36 lbs. 640.00
EA AU675S 1hp, 115v,1ph 100 gpm @ 5' Automatic 26' 9" x 22-13/16" 41 lbs. 787.00
EA U675S 1hp, 115v,1ph 100 gpm @ 5' Manual 26' 9" x 22-13/16" 41 lbs. 776.00
EA AU611S 1-1/2hp, 230v,1ph 107 gpm @ 10' Automatic 31' 9" x 20-1/4" 45 lbs. 855.00
EA U611S 1-1/2hp, 230v,1ph 107 gpm @ 10' Manual 31' 9" x 20-1/4" 45 lbs. 840.00
EA U615-1 2hp, 230v,1ph 124 gpm @10' Manual 46' 9" x 24" 52 lbs. 958.00
AU64S EA U615-3 2hp, 230v,3ph † 180 gpm @ 10' Manual 46' 9" x 24" 45 lbs. 830.00
D
EA U615-4 2hp, 460v,3ph † 180 gpm @ 10' Manual 46' 9" x 20-1/4" 45 lbs. 830.00
EA XPS5230 2hp, 230v,1ph 173 gpm @ 10’ Manual 55’ 9” x 24” 52 lbs. 995.00
*1-phase motors are 115 or 230 volt, 3-phase are 208/230 volt
**Maximum flow rates will decrease with higher discharge pressure or heads.
† You must run these pumps at 10’ minimum discharge head.
LSP03 Models are 1/3 HP, single phase, 115 volt. Standard with 10' power cords.
D Rated to 2.8 amps. 6-1/8" Diameter x 9-1/2" H. Weight is 11 lbs. LSP0311AT
LSP07 Models are 3/4 HP, single phase, 115 volt. Standard with 20' power cords.
Rated to 6.7 amps. 6-1/8" Diameter º x 11-1/4" H. Weight is 15 lbs.
LSP0711F
Part No. Motor **Max. Flow Control Shut-Off Net Ea.
D
GL LSP0311 1/3hp-115v 36 gpm @ 5' Manual 20' $ 143.00
GL LSP0311AT 1/3hp-115v 36 gpm @ 5' Automatic 20' 169.50
GL LSP0711F 3/4hp-115v 57 gpm @ 10' Manual 34' 211.50
GL LSP0711ATF 3/4hp-115v 57 gpm @ 10' Automatic 34' 237.50
** Flow rates will decrease with higher discharge pressure or head.
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0259
Submersible Sump Pumps 153
Specifically designed for Dewatering, Water Transfer, Sewage Systems or for any use where waste or drainage with up to 3" solids must be
disposed of. Mechanical shaft seals with Buna elastomers are standard. Rated to 104° F. continuous or 140° F. intermittent duty. Pump casings are
thermoplastic, stainless or cast iron as noted.
WW Series - 2"
WW Series pumps feature Thermoplastic casing, impeller and base. Motor
housing is cast iron. Motors are 1/2 HP, 1 phase, 115 volt and are available
with or without float switches. Power cord is 10' long. Handles solids up to
2" diameter. Outlet fitting is 2" FPT. WW
Series
Part No. Motor Flow Rate Shut-off Ht. Wt. Net Ea. D
GL WW0511 1/2 hp 63 gpm @ 10' 18' 22 lbs. $ 303.50
GL WW0511A * 1/2 hp 63 gpm @ 10' 18' 23 lbs. 338.50
* Standard with float switch for automatic shutoff.
Part No. Motor Flow Rate Shut-off Ht. Wt. Net Ea.
GL 1DV51COVA 1/2 hp 50 gpm @ 10' 26' 22 lbs. $ 560.00 D
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0258
154 Injection Metering Pumps
Injection Pumps Blue White
Adjustment
Dial
Pump/Tank Systems
The Star Systems from Blue White feature
the popular C15N Diaphragm Pumps with
a 15 gallon storage tank. One unit for
convenient chemical injection. Units are
pre-plumbed and ready-to-use.
D
Tanks feature a rectangular design for
floor or table placement. Lid allows
for opening, closing or venting. The
D most popular pumps are shown, but
C1700N Series many other pump/tank models are
(Dual Head)
available. Pumps are rated to 125
C1500N Series PSI. Dimensions are 22" high x
D 15-1/2" wide x 19-1/2" deep.
Blue-White Chemical Injection Pumps. Specifically designed for the Car
Wash industry. Ideal for dispensing a precise and wide variety of solutions.
Low-flow Chem-Feed pumps are for the new Super-concentrated solutions
on the market today. (Dual Head Units can apply different chemicals or the Double Ball Cartridge Valves
same chemical at different rates to different points.)
Standard Features include the following: Part No. Max. Oz/Min Tank Voltage Wt. Net Ea.
BL T15N102X15 1.70 15 gallon 115 27 lbs. $ 389.00
• Weather-resistant housing for indoor or outdoor use • Easy to adjust feed
BL T15N302X15 1.40 15 gallon 115 27 lbs. 389.00
rate; you always know exactly what your injection rate is • PVDF (Kynar)
BL T15N402X15 5.90 15 gallon 115 27 lbs. 389.00
pump heads • All-bearing gear motor for stronger and smoother operation •
BL T15N404X15 10.60 15 gallon 115 27 lbs. 389.00
Double-sealed PVDF cartridge fittings to prevent costly leaks • Pressures
* 24 Volt Models available on request.
to 125 psi (70 PSI on 10 oz. and Larger) • Chemically resistant internals •
Anti-siphon check valve and foot valve strainer • ETL Listed • Can be wall
or shelf mounted • Viton® O-ring & Teflon/EP Diaphragm • 110 or 24 Volt
• Amp draw on 115 volt is .74 startup and .45 running. Amp draw on 24
volt is 3.4 startup and 2.0 running • Dimensions: 9-1/16" H x 4-1/2" W x C1500N Parts
5-3/4" D on Model C1500N. 9-1/2" H x 7-1/2" W x 4" D on Model C1700N
• Maximum fluid temperature is 130° F. Includes 3/8” OD suction and Breakdown
discharge tubing, flow indicator and mounting hardware.
Conversion
kits
are available to
conver t older
style high flow
pumps to low
flow pumps.
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0254
WANNER Diaphragm Pumps & Accessories 155
WANNER
Hydra-Cell Pumps
For Difficult fluids such as:
• Reclaim Water
• Abrasives
• Hot Solutions to 250° F D
Model D10: Rated to 8.0 GPM and 1000 PSI @ 1450 RPM. Shaft
diameter is 7/8". Dimensions- (10-3/4" L x 7-1/4" W x 7-7/8" H). (Note: *Max. *Max. Max.Req'd
This pump can be ordered at flow rates of 4 or 6 GPM @ 1750 RPM Part No. Flow Pressure HP Wt. Net Ea.
if required.) Inlet is 1" and Outlet is 3/4". WN D10 8.0 GPM 1000 PSI 5.8 45 lbs. $ 1025.00
WN D15 13/10 GPM 1500/2500 PSI 15.6 145 lbs. 3118.00
Model D15: Rated to 13 GPM @ 1500 PSI or 10 GPM @ 2500 PSI. WN H25 20 GPM 1000 PSI 13.9 120 lbs. 2398.00
Shaft diameter is 1-1/8". Dimensions- (16" L x 10" W x 12-1/2" H). Inlet is WN D35 36 GPM 1200 PSI 30.0 240 lbs. 4366.00
1-1/4" FPT and Outlet is 3/4" FPT. WN C22A Pressure Regulator, 10 GPM, 1000 PSI................ 199.00
WN C62B Pressure Regulator, 14 GPM, 2500 PSI................ 239.50
Model H25: Rated to 20 GPM and 1000 PSI @ 1050 RPM. Shaft WN C23A Pressure Regulator, 20 GPM, 1000 PSI................ 280.00
diameter is 1-1/8". Dimensions- (15-1/2" L x 9-1/2" W x 10" H). Inlet is WN C24A Pressure Regulator, 40 GPM, 1000 PSI................ 622.00
1-1/2" and Outlet is 1". WN 3431 Oil - One Quart Size (HYDRAOIL 10W30) ........... 6.95
WN 3432 Oil - 2-1/2 Gallon Size (HYDRAOIL 10W30) ........ 63.95
Model D35: Rated to 36 GPM and 1200 PSI @ 1050 RPM. Shaft For specific applications, special materials of construction are available.
diameter is 2". Dimensions- (21" L x 11-1/2" W x 15" H). Inlet is Please give pumping requirements when ordering.
1-1/2" and Outlet is 1".
* Note: Optimum Usage of Above Pumps is 10% under full rating.
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0607
156 Peristaltic & Reclaim Pumps
Peristaltic Metering Pumps
STENNER Peristaltic Pumps are designed to offer accurate dosing of chemicals and solutions to a wide variety of industrial applications. Self-priming
to 25’. Roller tube design offers precise adjustable injection rates from 5 to 100% concentrations. Pressures to 100 PSI and temperatures to 125° F.
Standard tubes are 1/4” O.D. (3/8” also available). Tube construction is Santoprene but Tygothane tubes are also available for petroleum products, oils
and solvents.
Available in single, double and triple head designs for multiple chemicals or higher flow rates. Motors are 120V, 60Hz but 230V 50 or 60Hz are also
available. Tanks are available in 7, 15 or 30 gallon sizes in translucent white or UV resistant gray. Tanks also come with grommets and mounting screws.
Pre-assembled pump/tank systems are also available in many different configurations. All pumps are rated for continuous duty.
Classic 85 UV Gray
SVP Series
Series Tank
D D Tank/Pump D D
Package
Classic 85 Series Pumps feature adjustable output from 5 to 100% in SVP Series Pumps feature adjustable output from 5 to 100% in 1%
2.5% increments with a dial gear adjustment. Six interchangeable tubes. increments with a digital keypad adjustment. Six interchangeable tubes.
Dimensions are 5” x 8” x 6”. Rated to 100 PSI, 40 GPD and 44 RPM. Dimensions are 5” x 6” x 10”. Rated to 100 PSI, 44 GPD and 47 RPM.
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0712
Chemical Pumps 157
Part No. Description Wt. Net Ea. GPI® Chemical Pump & Meter Repair Kits
SI CES-PH6 12 Volt Pump with SEM-10 Meter,
Hose & Nozzle & 2" x 1” Suction Elbow..... 25 lbs. $ 659.00 Part No. GPI REPAIR KITS Net Ea.
SI CES-PH610 12 Volt Pump with SEM-10 Meter, GI 110904-1 Seal Kit For M120H & M1100H ................ $ 41.00
Hose & Nozzle w/GEM Cap Adapter... 25 lbs. 639.00 GI 110907-1 Gear Kit For M120H & M1100H ............... 23.90
GI 110531-01 Switch Kit For M120H & M1100H . ........... 14.45
SI CES-MTS * 12 Volt Pump with SEM-10 Meter,
GI 110504-1 Repair Kit for M120 .................................. 40.45
Hose & Nozzle with Monsanto Camlock.... - 719.00 GI 118501-1 Gear Kit for P120H & P200H . ................. 43.20
SI CADDY-PH6 12 Volt Pump with SEM-10 Meter, GI 118503-1 Overhaul Kit for P120H & P200H ............. 83.05
Hose & Nozzle in Caddy Frame........... 35 lbs. 889.00 GI 118504-1 Overhaul Kit for P200H ............................ 100.00
SI CADDY-PH603 110 Volt Pump with SEM-10 Meter, GI 118505-1 Drive Shaft Kit for P120H & P200H .......... 58.50
Hose, Nozzle in Caddy Frame............. 25 lbs. 1076.00 GI 118506-1 Seal Kit for P120H & P200H .................... 47.50
SI KD04200 1” x 3/4” Suction Tube......................... - 23.20 GI 111507-1 Overhaul Kit for FM100H . ........................ 44.70
GI 120500-1 Overhaul Kit for FM300H . ........................ 58.20
* For Mansanto Keylock Tanks Only.
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0272
158 Chemical Pumps
DD6 Pump/Motor BC6 Pump & Motor
The DD6 Diaphragm Pump is
designed to mount directly into the DD6
Pump BC6
mini-bulk container. The DD6 will Pump
pump low to high viscosity liquids.
The discharge port configuration
features a check valve to prevent
chemical container leakage as
the motor discharge hose is
designed to break away in the D
event of an accident. This pump
includes a manual vent, rain cover, D
D
mounting hardware and gasket. The flow
rate is 7 to 9 GPM. Recirculates when hose
end valve is shut off.
KD2301 KD23AC
Elbow Kit, 1" FPT Elbow Kit, 1" Male The BC6 Diaphragm Pump
Adapter (camlock) looks similar and functions
identically to the DD6 pump but
Part No. Wt. Net Ea. it is designed to fit directly onto
SI DD6PUMP DD6 Pump Module Only LESS MOTOR............... 4 lbs. $ 218.00 ICB containers (mini-bulks)
SI DD6MOTOR 12 Volt Motor Only for DD6 or BC6 Pump.......... 12 lbs. 259.00 which have 6.5” diameter nomi-
SI KD23AC Elbow Kit with Male QC Adapter.......................... - 84.70 nal (6 7/16” diameter actual)
SI KD2301 Elbow Kit with 1" FPT.......................................... - 77.40 tank openings. The BC6 pump
SI DD6M-100 Viton® O-Ring (Smaller) for Elbows........................ - 1.80 will pump low to high viscosity
SI EP-37 Viton® O-Ring (Larger) for Elbows.......................... - 8.36 liquids. Flow rate is 7-9 GPM.
SI DD6M-105 Spacer for Elbows............................................... - 2.84 The BC6 pump will work with
SI KD04200 34" Suction Tube w/ith Flex Connection & Clamps... - 23.20 either the DD6 motor (blue
SI RKDD6 Repair Kit for DD6 Pump.................................... - 85.05 version) or with the BC6 motor
SI SPAN Spin Collar for GEM Cap Tanks .......................... - 25.10 (both are 12V DC). BC6 Pump
SI SPA700G Gasket for Spin Collar......................................... - 27.25 includes 1” plastic discharge
elbow & 1” suction tube.
BC6 Mounted On 275 Gallon Square Tank
Complete DD6 Kits Part No. Wt. Net Ea.
SI BC6PUMP BC6 Pump Module Only LESS MOTOR............ 4 lbs. $ 233.00
SI DD6MOTOR 12 Volt Motor Only for DD6 or BC6 Pump....... 12 lbs. 259.00
SI BC6MOTOR * 12 Volt Motor Only for BC6 Pump ONLY . .... 12 lbs. 299.00
* No Top Cover on BC6MOTOR.
Complete BC6 Kits
1A100
Kit
The 1A100 Drive Package includes the DD6 motor, SEM-10 electronic flow meters,
discharge elbow (KD2301; 1” FPT), and a 1” x 12”, 2-braid, 4-ply EPDM discharge hose
assemblies with nozzle valve. 1A101 adds DD6 pump. Suction tube is extra.
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0271
Chemical Pumps 159
The SOTERA 400B Series Diaphragm Pumps have proven to be a winner on all types of hard to handle agricultural chemicals. The double
acting diaphragm design will work well with viscous, corrosive, encapsulated, suspension and shear sensitive products. These self priming pumps
operate well on cold mornings and can even run dry without damage. These pumps have a 5-year Warranty. Working parts run in oil. Wetted
parts are polypropylene, santoprene and stainless steel. The 1/4 HP motor will flow 13 GPM on 12-volt and 16 GPM on 110-volt models. Easily
adapted to all mini-bulks with various adapters (see below).
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0273
HAND & DRUM PUMPS 163
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0275
164 Barrel & Drum Hand Pumps
Drum and Barrel Pumps for a wide variety of transfer applications. Designed for Acids, Alkalis, Solvents, Detergents, Chlorine, Petroleum
Products, Dairy Chemicals and Water Removal. Most pumps are sold with 2” IPS adapters for the most common drums and barrels. However,
ACT or Rieke Buttress, Glass Carboy and Poly Carboy adapters are also available. Pumps are offered with discharge hose or spouts as
shown. (Note: Pump and chemical compatibility should always be checked before use.)
transfer of up to 50% Sulfuric Acid at up to reach the bottom of chemical containers. 2” IPS DP12SPS
to 120° F. bung adapter is also included. DP18SPS
Model 436 features PVC barrel and
shaft with “Hypalon” seals and valves. DAIRY CHEMICAL PUMPS
36” polyethylene discharge hose is Part No. Length Seal Output/Stroke Net Ea.
included. Best choice for Alkalis. 236 BI DP12SPS 12” Hypalon 5 oz. $ 31.75
UL listed for transfer of up to 30% 436 BI DP18SPS 18” Hypalon 8 oz. 34.75
Hydrochloric Acid at up to 100° F.
Model 336 offers an effective and easy way to Models 230PF & 136PF6 Pumps are designed for manual removal of
transfer oils, kerosene, diesel fuel, etc. Features water when electrical means are not available. Just place pump end in
PVC barrel with urethane valves and Buna seals.
D water and up/down motion removes water easily and quickly. Construction
Pumps are 38” long x 1-1/2” diameter. Rated to is high impact PVC. No priming is required. 36” discharge hose is included
with both models.
28 oz. per stroke. 36” Discharge hose and 2” IPS
bung adapter is included. Models 915F Compact hand water pump. Includes 2” x
336PF3S
36” flexible intake tube with foot valve and 7’ outlet tube D
for directing discharge flow. Pump is 3” diameter x 24”
PETROLEUM PUMP long. Output is as high as 16 GPM. Construction is PVC.
Part No. Seal Output/Stroke Net Ea.
BI 336PF3S Hand Pump Buna 28 oz. $ 56.95
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0949
HAND PUMPS 165
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0274
166 Drum Pumps
Motor Driven Drum Pumps 316SS Rotary
Motor Driven Drum Pumps from Standard Pumps. Engineered for
Hand Drum Pump
transferring a wide range of aggressive and corrosive liquids as well as Stainless Steel Drum Pump is designed for use in dispensing and
light oils. All pumps carry a 3-Year warranty. transferring chemicals and liquids including many acids, acetones, alcohols,
trichloroethylene, solvents, photographic chemicals and ketones which are
compatible with pump component materials.
• Padlock Provision.
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0866
Submersible Well & Jet Pumps 167
Determine the Flow Rate of Your Pump in Gallons Per Hour • Choose Your Pressure Switch Setting •
Select the Tank from the Chart Below with Drawdown at Your Chosen Switch Setting that is Equal to or Above Your Pump GPH.
Pump GPH 240 300 360 420 480 540 600 720 840 960 1080 1200 1320 1500 1800 2100 2400 2700 3000 3600 4800 6000 7200
Tank
Breakdown* 4 5 6 7 8 9 10 13 17 20 25 30 36 44 60 70 80 90 100 120 160 200 240
Gallons
* The amount of usable water discharged between pump cycles of an automatic water system.
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0279
168 Water Pressure Booster Pumps • Tanks
Pressure Booster Pumps Booster Pumps
Pressure Booster Pumps for a wide variety of pumping applications.
Ideal for increasing rinse water pressure, liquid transfer, spot-free water
re-pressurization, lawn sprinkler and many others. Standard construction Sta-Rite Pressure Booster Pumps are an ideal choice for boosting water
is Stainless Steel or Cast Iron. (Not Self-priming). Maximum temperature pressures for washing, RO rinse water and general purpose pumping.
is 160° F. - water only. Patented, Multi-stage design. Carbon/Ceramic/Buna shaft seals. Stainless
APPLICATION FOR: steel pump and motor shaft. Cast iron or Stainless steel inlet and outlet ports.
• Residential, commercial or agricultural • Spray systems Rated to 140° F. and 80 psi inlet pressure. (Not Self-priming).
pressure wash • Water circulation
• Reverse osmosis • Filtration
• Evaporative cooling systems/misters • HVAC
• Booster Service • General purpose pumping
Motors are 60HZ, 3500 RPM, TEFC, and are available in either single phase, Motors are ODP (TEFC available on request). All single phase motors to
115/230 volt or three phase, 208/230/460 volt. 2 HP are 115/230 volt. All pumps feature 3/4" FPT inlet and outlet except
Cast Iron Pumps feature cast iron inlet and discharge fittings and 304SS for HP20 series which are 1" FPT. 3-HP 1-Phase Motors are 208/230 volt.
stainless pump shell. Mechanical seal and BUNA elastomers are standard. All 3-HP 3-Phase Motors are 208/230/460 volt.
Stainless Steel pumps feature 304SS stainless steel inlet and discharge
fittings and pump shell. Mechanical seal and Viton® elastomers are standard. Part No. Ports Motor Flow Rate Wt. Net Ea.
SA HP10D 3/4" Cast Iron 3/4 hp, 1 ph 10 GPM @ 100 psi 46 lbs. $ 485.00
Part No. Castings Motor Ports *Flow Rate Wt. Net Ea. SA HP10E 3/4" Cast Iron 1 hp, 1 ph 10 GPM @ 135 psi 50 lbs. 499.00
GL 7GBC1014RO Cast Iron 1hp, 1ph. 1" FPT 5 GPM @ 180 PSI 65 lbs. $ 596.00 SA HP7E 3/4" Cast Iron 1 hp, 1 ph 6 GPM @ 195 psi 51 lbs. 535.00
GL 7GBS1014R4 Stainless 1hp, 1ph. 1" FPT 5 GPM @ 180 PSI 65 lbs. 752.00 SA HP10FMS 3/4" Cast Iron 1.5 hp, 1 ph 8 GPM @ 200 psi 58 lbs. 570.00
GL 10GBC1514QO Cast Iron 1.5hp, 1ph. 1" FPT 8 GPM @ 180 PSI 56 lbs. 604.00
SA HP10G 3/4" Cast Iron 2 hp, 1 ph 10 GPM @ 195 psi 63 lbs. 593.00
GL 10GBS1514Q4 Stainless 1.5hp, 1ph. 1" FPT 8 GPM @ 180 PSI 56 lbs. 792.00
GL 10GBC2014SO Cast Iron 2hp, 1ph. 1" FPT 12 GPM @ 180 PSI 73 lbs. 675.00
SA HP10G3 3/4" Cast Iron 2 hp, 3 ph 10 GPM @ 195 psi 59 lbs. 569.00
GL 10GBS2014S4 Stainless 2hp, 1ph. 1" FPT 12 GPM @ 180 PSI 73 lbs. 829.00 SA HP20G 1" Cast Iron 2 hp, 1 ph 15 GPM @ 145 psi 62 lbs. 549.00
GL 10GBC2015SO Cast Iron 2hp, 3ph. 1" FPT 12 GPM @ 180 PSI 64 lbs. 660.00 SA HP20G3 1" Cast Iron 2 hp, 3 ph 15 GPM @ 145 psi 58 lbs. 475.00
GL 10GBS2015S4 Stainless 2hp, 3ph. 1" FPT 12 GPM @ 180 PSI 64 lbs. 812.00 SA HP20H 1" Cast Iron 3 hp, 1 ph 20 GPM @ 195 psi 59 lbs. 759.00
GL 18GBC2014NO Cast Iron 2hp, 1ph. 1" FPT 15 GPM @ 150 PSI 73 lbs. 649.00 SA HP20H3 1" Cast Iron 3 hp, 3 ph 20 GPM @ 195 psi 55 lbs. 770.00
GL 18GBS2014N4 Stainless 2hp, 1ph. 1" FPT 15 GPM @ 150 PSI 73 lbs. 798.00 SA HPS7E 3/4" Stainless 1 hp, 1 ph 6 GPM @ 195 psi 51 lbs. 689.00
GL 18GBC2015NO Cast Iron 2hp, 3ph. 1" FPT 15 GPM @ 150 PSI 64 lbs. 610.00 SA HPS10FMS 3/4" Stainless 1.5 hp, 1 ph 8 GPM @ 200 psi 58 lbs. 698.00
GL 18GBS2015N4 Stainless 2hp, 3ph. 1" FPT 15 GPM @ 150 PSI 64 lbs. 759.00 SA HPS10GMS 3/4" Stainless 2 hp, 1 ph 10 GPM @ 195 psi 63 lbs. 779.00
GL 18GBC3014QO Cast Iron 3hp, 1ph. 1" FPT 22 GPM @ 130 PSI 77 lbs. 847.00
SA HPS10G3 3/4" Stainless 2 hp, 3 ph 10 GPM @ 195 psi 59 lbs. 735.00
GL 18GBS3014Q4 Stainless 3hp, 1ph. 1" FPT 22 GPM @ 130 PSI 77 lbs. 998.00
GL 18GBC3015QO Cast Iron 3hp, 3ph. 1" FPT 22 GPM @ 130 PSI 65 lbs. 847.00
SA HPS20GMS 1" Stainless 2 hp, 1 ph 15 GPM @ 145 psi 62 lbs. 719.00
GL 18GBS3015Q4 Stainless 3hp, 3ph. 1" FPT 22 GPM @ 130 PSI 65 lbs. 998.00 SA HPS20G3 1" Stainless 2 hp, 3 ph 15 GPM @ 145 psi 58 lbs. 647.00
GL 45HB25013 † Cast Iron 5hp, 1ph. 2" FPT 30 GPM @ 115 PSI 147 lbs. 2245.00 SA HPS20H 1" Stainless 3 hp, 1 ph 20 GPM @ 155 psi 59 lbs. 989.00
GL 45HB25035 Cast Iron 5hp, 3ph. 2" FPT 30 GPM @ 115 PSI 99 lbs. 1470.00 SA HPS20H3 1" Stainless 3 hp, 3 ph 20 GPM @ 155 psi 55 lbs. 865.00
GL 45HB27535 Cast Iron 7.5hp, 3ph. 2" FPT 50 GPM @ 125 PSI 150 lbs. 1817.00 SA HP30H 1-1/4" Cast Iron 3 hp, 1 ph 30 GPM @ 125 psi 59 lbs. 832.00
GL 45HB21135 Cast Iron 10hp, 3ph. 2" FPT 60 GPM @ 125 PSI 190 lbs. 2022.00 SA HP30H3 1-1/4" Cast Iron 3 hp, 3 ph 30 GPM @ 125 psi 55 lbs. 895.00
*Flow rates can be increased if discharge pressure is decreased. Pump curves SA HPS30H 1-1/4" Stainless 3 hp, 1 ph 30 GPM @ 125 psi 59 lbs. 959.00
available on request. SA HPS30H3 1-1/4" Stainless 3 hp, 3 ph 30 GPM @ 125 psi 55 lbs. 942.00
† 208/230 V.
Precharged Water Tanks Model LT2 / LT7 is a small compact unit that is standard with a 3/4" MNPT
VT120
VT85 connection on the bottom. Can be plumbed directly onto the pump. Capacity
is 2 gallons. LT5 has 1/4” MPT inlet.
VT60
Model HT14 is a Horizontal model that includes the MB1 pump mounting
bracket. Capacity is 14 gallons. HT14V is a Vertical Style. 1" FNPT.
Models VT20 & VT36 are vertical models. Connections are 1" FNPT.
Models VT60, VT85 & VT120 are vertical models & have 1-1/4"
VT20 connections.
Tank Drawdown DIMENSIONS
Part No. Capacity @ 30 PSI Diameter x Height Wt. Net Ea.
D
SR LT2 2.0 gallon .7 GPM 8" x 12" 5 lbs. $ 49.50
SR LT5 5.0 gallon 1.5 GPM 11" x 15" 10 lbs. 51.95
SR LT7 6.0 gallon 1.8 GPM 12" x 16" 18 lbs. 71.95
SR HT14 * 14 gallon 4.3 GPM 21"x16" 28 lbs. 115.00
D SR HT14V 14 gallon 4.1 GPM 16" x 23" 37 lbs. CALL
SR VT20 19 gallon 5.8 GPM 16" x 27-1/2" 40 lbs. 102.00
VT36
HT14 SR VT36 33 gallon 11.3 GPM 16” x 43” 49 lbs. 194.00
LT2, LT5 & LT7 SR VT44 44 gallon 15.0 GPM 53” x 36” 67 lbs. 269.00
Pre-charged water tanks for use with water systems or holding tanks. Designed to SR VT60 62 gallon 18.3 GPM 24" x 39-1/2" 112 lbs. 333.50
SR VT85 81 gallon 27.0 GPM 53" x 62" 99 lbs. 326.00
give constant pump pressure. Reduces the amount of pumping cycles required which
SR VT120 119 gallon 40.0 GPM 66" x 60" 153 lbs. 540.00
helps extend pump life. Available in Vertical or Horizontal models.
* HT14 is a horizontal style tank with mounting plate.
Drawn steel construction with baked-on, polyester, painted finish. Standard with PVC
diaphragms. Maximum working pressure is 100 PSI. Precharge pressure is 40 psi. FDA
Viton® is a registered trademark of DuPont Performance Elastomers
approved. Maximum temperature is 120° F. All units are standard with air valves.
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0280
Jurop Vacuum Pumps 169
* Max. HP
Part No. CFM Required Wt. Net Ea. Ref.# Description
CB PN23 †Pump Only 92 4-1/2 117 lbs. $ 1195.00 1 PN Series Pump
CB PN33 †Pump Only 127 6 139 lbs. 1275.00 D 6 Mounting Stand Pump Packs Also
CB PN58 †Pump Only 230 9 225 lbs. 1595.00 7 3-Shaft Gear Box Available Call for Pricing!
8 Coupling Kit
CB PN84 †Pump Only 317 15 254 lbs. 1775.00 9 Alignment Bracket
* Free Air CFM. † Indicate Clockwise or Counterclockwise.
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0812
170 Vacuum Pumps
Vacuum Pumps Vacuum Power Packs
Conde Vacuum Pumps are rated from 35 to 230 CFM. Designed for tanks Vacuum only or Vacuum/Pressure Power Packs featuring Conde Vacuum
from 50 to 2500 gallons. Available in Vacuum only or Vacuum/Pressure Pumps shown on this page. All pump units are standard with Honda Gas
models. Vacuum only pumps are an economical option when pressure is Engines, stainless steel baseplates, stainless belt guards, dual groove
not required for off-loading. All units can be driven by a variety of sources pulleys and vacuum relief valves. Engines are shown with or without electric
such as gas engine, PTO, hydraulic, gear box or 12 volt clutch. All pumps start as noted. All units are pre-assembled and ready for installation to
are available for clockwise or counterclockwise rotation as noted. your tank or truck. Standard With:
PMS6AV
Pumps shown below come standard with automatic oilers that require no PowerPak • Honda Gas Engines
adjustments. Compact, low profile design allows for ease-of-installation. Vacuum/Pressure • Stainless Steel Baseplates
Sealed bearings require no maintenance. All pumps are rated to 28” of • Stainless Belt Guards
intermittent vacuum and 20” continuous vacuum. Pumps with pressure
• Dual Groove Pulleys
option are rated to 20 PSI discharge.
Pro3, Super6 and SDS6 models include vacuum relief valves. All pumps • Vacuum Relief Valves
PMS6V
are tested prior to shipping and carry a 1-Year Warranty. (Specify tapered PowerPak
shafts if clutch drive is required). Vacuum Only
D
SPECIFICATIONS
PUMP SERIES Speed Range Shaft Size Port Size Ideal Tank Size Ideal for tanks from
Pro3 1200-1750 3/4” 1” 50-300 Gallon 1000 - 2000 gallons
Super6 1200-1750 1” 1-1/4” 300-500 Gallon
SDS6 1200-1750 1” 1-1/2” 500-1000 Gallon
D
SDS12 1200-1750 1-1/8” 1-1/2” 1000-2000 Gallon
ULTRA12 1200-1750 1-1/8” 1-1/2” 1200-2500 Gallon Ideal for tanks from
200 - 500 gallons
PRO3 SUPER6 Vacuum Only
Vacuum Only - 70 CFM - ESTIMATED TANK PULL DOWN TIME (15” Hg)
- 35 CFM -
TANK SIZE SDS12 SDS6 Super6 ProVac3
100 Gallon - - 8 sec. 16 sec.
200 Gallon - - 17 sec. 37 sec.
300 Gallon - - 25 sec. 50 sec.
400 Gallon - - 34 sec. 64 sec.
D 500 Gallon 16 sec. 26 sec. 52 sec. 84 sec.
750 Gallon 24 sec. 40 sec. - -
D
1000 Gallon 32 sec. 53 sec. - -
1500 Gallon 50 sec. 80 sec. - -
Ideal for tanks from 2000 Gallon 67 sec. 106 sec. - -
300 - 500 gallons
Ideal for tanks from
Part No. Pump Series Engine Vac/Pressure Wt. Net Ea.
50 - 300 gallons
DU PM3V Pro3 4 HP, Rope Pull Vac 112 lbs. $ 1705.00
Vacuum Only Pumps DU PM3AV Pro3 5-1/2 HP, Rope Pull Vac/Pressure 112 lbs. 2084.00
Part No. Pump Series Vacuum Rotation Wt. Net Ea. DU PMS6V Super6 5-1/2 HP, Rope Pull Vac 155 lbs. 2166.00
CO OL3PW Pro3 35 cfm Clockwise 40 lbs. $ 669.00 DU PMS6AV Super6 5-1/2 HP, Rope Pull Vac/Pressure 155 lbs. 2275.00
CO OL3PC Pro3 35 cfm Counterclock 40 lbs. 669.00 DU PMSD6V SDS6 9 HP, Electric Vac 225 lbs. 2714.00
CO OL6SW Super6 70 cfm Clockwise 75 lbs. 975.00 DU PMSD6AV SDS6 9 HP, Electric Vac/Pressure 225 lbs. 3002.00
CO OL6SC Super6 70 cfm Counterclock 75 lbs. 975.00 DU PMSD12V SDS12 13 HP, Electric Vac 290 lbs. 3147.00
CO OL6SDSW SDS6 115 cfm Clockwise 100 lbs. 1098.00 DU PMSD12AV SDS12 13 HP, Electric Vac/Pressure 290 lbs. 3431.00
CO OL6SDSC SDS6 115 cfm Counterclock 100 lbs. 1098.00
CO OL12SDSW
CO OL12SDSC
SDS12
SDS12
190 cfm
190 cfm
Clockwise
Counterclock
150 lbs.
150 lbs.
1298.00
1298.00 Mount Drive Base
CO OL12ULW Ultra12 230 cfm Clockwise 165 lbs. 1479.00 Mount Drive Base for use with right angle gear boxes. 1RA
CO OL12ULC Ultra12 230 cfm Counterclock 165 lbs. 1479.00 Easily bolts to truck frame. Can be used with any of Right
the SDS pumps, either vacuum or vac/pressure. Heavy D Angle
construction and CNC machined for extra strength. Drive Base
D D
Vacuum Tree
D D
SPECIFICATIONS:
• 1.5 HP/110 Volt Motor Draws 13.4 Amps, • Tank Volume, 52 Gallons
Works On Any 15 Amp Service • Air Volume, 35 CFM
• 24” Wide x 45” High x 50” Long • 25’ Power Cord
• Operating Vacuum, 16” hg. • Weight is 370 lbs.
• Operating Pressure, 5 PSI
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0825
174 PLUNGER PUMPS
Low Flow Models (3 to 6 GPM)
CAT PUMPS® TRIPLEX PLUNGER PUMPS are designed to deliver smooth, low pulsation flows at a wide variety of
pressures and flow rates. Widely used in continuous-duty, high pressure applications including Car/Truck Wash, Industrial
Cleaning, Pressure Washing, Reverse Osmosis, Water Misting and many more.
CAT PUMPS® are the “Pumps with Nine Lives”. Standard Features include: High pressure seals that are lubricated
and cooled by the solution being pumped • Oil-bath crankcase • Heat treated valves and seats • Forged brass or
stainless steel manifolds • Solid ceramic plungers • Exclusive high pressure seal design • Rated from 140° to 160° F.
depending on the model. Seal options up to 180° F. available • Wet ends can be serviced without entering the crankcase.
Note: Mounting rails and mounting kits are not included and must be ordered separately).
Low Flow pumps are rated from 3 to 6 GPM. See following page for high flow models.
D
D
D D
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0282
PLUNGER PUMPS 175
D
D
D
D
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0913
176 High Pressure Pumps
“SuperFlow” Plunger Pumps
Close-Coupled D
Pump &
Motor Units
D
Close-Coupled Pump and Motor Units from Cat Pumps® eliminate
D cumbersome belts and pulleys and the need for clumsy belt guards. At
2SF pressures up to 2000 PSI at 4 GPM, these units all incorporate the popular
4SF
CAT PUMPS® CERAMIC PLUNGER PUMP.
Direct Drive Plunger Pumps from Cat Pumps®. Designed to run at direct Motors are Totally Enclosed, Fan Cooled, 1725 RPM and available in single
electric motor or gas engine speeds. Pumps feature hollow shafts, mounting and three-phase (Baldor Brand).
flange and pressure unloader valve. Ports are 1/2” inlet x 3/8” outlet.
Maximum Electric Motor
2SF Series are rated to 2000 PSI and 3.0 GPM. Designed for electric motor Part No. PSI @ GPM 230/460-Volt Wt. Net Ea.
or gas engine drive at the RPM shown. 2SFX Pumps are the same as 2SF CC 340BD31 1200 4 3 HP 1 Phase 90 lbs. $ 1703.00
but with newly designed flanges and comes with a bypass hose. Both series CC 340BD33 1200 4 3 HP 3 Phase 90 lbs. 1339.00
are rated to 160° F. with seal options up to 190° F. CC 340BD51 2000 4 5 HP 1 Phase 105 lbs. 1798.00
4SF Series are rated to 3500 PSI and flow to 5 GPM. Designed for electric CC 340BD53 2000 4 5 HP 3 Phase 105 lbs. CALL
motor or gas engine drive at the RPM shown. Rated to 160° F.
For Electric Motors Gear Reduction Plunger Pumps
Part No. GPM PSI RPM Drive Shaft Wt.
Cat Pumps® Gear Reduction Pump Units
CC 2SF22ELS 2.2 2000 1725 Electric 5/8" 11 lbs.
CC 2SF29ELS 2.8 1500 1725 Electric 5/8” 11 lbs. are designed to mount-up directly to gasoline
CC 2SF20ES 2.0 2000 3450 Electric 5/8” 11 lbs. engines. Eliminates the need for belts, pulleys
CC 2SFX20ES 2.0 2000 3450 Electric 5/8” 11 lbs. and belt guards. Gearbox design (ratio of
CC 2SF22ES 2.2 2000 3450 Electric 5/8” 11 lbs. 2.0384:1) allows pumps to run at normal RPM.
CC 2SFX22ES 2.2 2000 3450 Electric 5/8” 11 lbs. CALL D All pumps shown are “Triplex Plunger”
CC 2SF30ES 3.0 1500 3450 Electric 5/8” 11 lbs. for design. These pumps feature ceramic
CC 2SFX30ES 3.0 1500 3450 Electric 5/8” 11 lbs. PRICING plungers for long life and abrasion resistance.
CC 2SF30GES 3.0 2000 3450 Electric 3/4” 11 lbs. Triplex design provides low pulsation and
CC 2SFX30GES 3.0 2000 3450 Electric 3/4” 11 lbs.
CC 4SF40ELS 4.0 3500 1725 Electric 1-1/8” 24 lbs.
quiet operation. Internally lubricated and cooled
CC 4SF45ELS 4.5 3000 1725 Electric 1-1/8” 24 lbs. packings for extended life.
CC 4SF50ELS 5.0 3000 1725 Electric 1-1/8” 24 lbs. The gearbox on each unit features hardened steel helical gears for smooth, quiet
For Gas Engines operation. Totally sealed housing provides independent gearbox lubrication.
Part No. GPM PSI RPM Drive Shaft Wt.
CC 2SF30GS 3.0 2000 3450 Gas 3/4" 11 lbs. Maximum Required Engine:
CC 2SF35GS 3.5 2000 3450 Gas 3/4” 11 lbs. Part No. GPM @ PSI Shaft Dia. HP Net Ea.
CC 2SFX30GS 3.0 2000 3450 Gas 3/4” 11 lbs. CALL CC 3CP1120G 3.5 2200 3/4" 5-7 HP $ 659.00
CC 2SFX35GS 3.5 2000 3450 Gas 3/4” 11 lbs. for CC 45G1 4.5 3500 1" 11-16 HP 1076.00
CC 4SF35GS1 3.5 3500 3450 Gas 1” 24 lbs. PRICING CC 5CP3120G1 4.5 3500 1" 18-20 HP 910.00
CC 4SF40GS1 4.0 3500 3450 Gas 1” 24 lbs. CC 5CP5140G1 5.5 3500 1” 18-20 HP 1036.00
CC 4SF45GS1 4.5 3000 3450 Gas 1” 24 lbs. CC 60G1 4.5 4000 1” 18-20 HP 1565.00
CC 4SF50GS1 5.0 3000 3450 Gas 1” 24 lbs. CC 70G1 4.5 5000 1” 22-24 HP 1930.00
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0293
GENERAL / INTERPUMP High Pressure Pumps 177
Triplex and Duplex Plunger Pumps from General/Interpump. Available in Pulley Drive or Direct-Drive
Designs. Maximum operating temperature on most pumps is 165° F. Maximum inlet pressure is 125
PSI. (5 year limited warranty on all pumps and a lifetime warranty on manifolds against damage
from freezing.)
Standard Features
Forged Bronze Head. Highly resistant to chemical corrosion.
Unitized Valves. Easily serviced. Valves are heat treated and seats are roller burnished to provide a
tight seal and extended valve life.
Continuously Lubricated Dual Packing System. Keeps packings cool by recycling water back into
system. Pre-loaded packings eliminate need for external gland adjustment and greasing.
Solid Ceramic Plunger. Extremely hard, won’t score. Precision micron finish produces excellent seal,
reduces wear on packings.
D
Replaceable Piston Guides. Made of Teflon, graphite and bronze alloy to prolong crankcase life.
CW2040
Cast Aluminum Crankcase. Large capacity means better lubrication for long life operation.
Connecting Rods. Large, full contact rods result in lower bearing pressure and added strength.
Tapered Roller Bearings. Oversized to evenly distribute load for longer, more quiet bearing life.
Forged and Hardened Steel Crankshaft.
Mounting Rails. Standard with mounting rails and mounting bolts for ease in installation.
Drive Design. Standard with shaft on right side when facing front of pump. (Left hand drive is available
but must be specified.)
D
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0286
178 General HIgh Pressure Plunger Pumps
Direct Drive • Forged Brass Manifolds
TT Series 51 Triplex Plunger Pumps with Hollow Shaft (Flanged for Direct Couple to Electric
Motor). NEMA-56C.
Maximum Max. Max. FPT Ports
Direct Part No. Pressure GPM RPM Shaft Inlet Outlet Wt. /Lbs. Net Ea.
Drive IP TT2021EBF 2000 2.1 3400 5/8" Hollow 3/8" 1/4" 11.5 $ 239.53
IP T9051EBF 1500 2.1 1750 5/8" Hollow 3/8" 1/4" 11.5 269.53
D IP TT9061EBF 1500 2.1 3400 5/8" Hollow 3/8" 1/4" 11.5 255.02
IP TT2028EBF 2000 2.8 3400 5/8" Hollow 3/8" 1/4" 11.5 231.53
5/8" Shaft IP TT9071EBF 1500 2.8 3400 5/8" Hollow 3/8" 1/4" 11.5 255.02
IP TT9111EBF 1500 3.0 1750 5/8" Hollow 3/8" 1/4" 11.5 249.53
EZ Series 44 Triplex Plunger Pumps with Hollow Shaft (Flanged for Direct Couple to Electric
Motor). NEMA-184C.
Maximum Max. Max. FPT Ports
Direct Part No. Pressure GPM RPM Shaft Inlet Outlet Wt. /Lbs. Net Ea.
Drive IP EZ2536E 2500 3.6 1750 1-1/8" Hollow 1/2" 3/8" 18.5 $ 315.54
D
IP EZ2542E 2500 4.2 1750 1-1/8" Hollow 1/2" 3/8" 18.5 359.06
IP EZ2545E 2500 4.6 3400 1-1/8" Hollow 1/2" 3/8" 18.5 315.54
IP EZ2555E 2500 5.5 3400 1-1/8" Hollow 1/2" 3/8" 18.5 315.54
IP EZ4035E34 4000 3.5 3400 1-1/8" Hollow 1/2" 3/8" 18.5 371.06
1-1/8" Shaft IP EZ4040E34 4000 4.0 3400 1-1/8" Hollow 1/2" 3/8" 18.5 371.06
TT Series 51 Triplex Plunger Pumps with Hollow Shaft, (Flanged for Direct Couple to Gasoline
Engines with 3/4" Shafts).
Direct Maximum Max. Max. FPT Ports
Part No. Pressure GPM RPM Shaft Inlet Outlet Wt. /Lbs. Net Ea.
Drive IP TT9061GBF 1500 2.1 3400 3/4" Hollow 3/8" 1/4" 11.4 $ 224.03
D
IP TT2028GBF 2000 2.8 3400 3/4" Hollow 3/8" 1/4" 11.4 231.53
IP TT9071GBF 1500 2.8 3400 3/4" Hollow 3/8" 1/4" 11.4 224.03
3/4" Shaft IP TT2035GBF 2000 3.5 3400 3/4" Hollow 3/8" 1/4" 11.4 231.53
IP TT1540GBF 1500 4.0 3400 3/4" Hollow 3/8" 1/4" 11.4 231.53
TX Series 63 Triplex Plunger Pumps with Hollow Shaft, (Flanged for Direct Couple to Gasoline
Engines with 3/4" Shafts).
TX Series 63 Triplex Plunger Pumps with Hollow Shaft, (Flanged for Direct Couple to Gasoline
Engines with 1" Shafts).
D
Direct Maximum Max. Max. FPT Ports
Drive Part No. Pressure GPM RPM Shaft Inlet Outlet Wt. /Lbs. Net Ea.
IP TX1506G8 3000 2.6 3400 1" Hollow 1/2" 3/8" 18.0 $ 266.03
IP TX1508G8 3000 3.0 3400 1" Hollow 1/2" 3/8" 18.0 266.03
IP TX1510G8 3000 4.0 3400 1" Hollow 1/2" 3/8" 18.0 266.03
1" Shaft
Direct Drive EZ Series 44 Triplex Plunger Pumps with Hollow Shaft, (Flanged for Direct Couple to Gasoline
Engines with 1" Shafts).
Maximum Max. Max. FPT Ports
Part No. Pressure GPM RPM Shaft Inlet Outlet Wt. /Lbs. Net Ea.
IP EZ3030G34 3200 3.0 3400 1" Hollow 1/2" 3/8" 19.1 $ 301.54
IP EZ3035G 3000 3.5 3400 1" Hollow 1/2" 3/8" 19.1 332.56
D IP EZ3040G 3000 4.0 3400 1" Hollow 1/2" 3/8" 19.1 375.05
IP EZ3045G 3000 4.6 3400 1" Hollow 1/2" 3/8" 19.1 332.56
Maximum Inlet Vacuum: Flooded
IP EZ4030G34 4000 3.0 3400 1" Hollow 1/2" 3/8" 20.0 $ 349.11
IP EZ4035G34 4000 3.5 3400 1" Hollow 1/2" 3/8" 20.0 349.11
1" Shaft IP EZ4040G34 4000 4.0 3400 1" Hollow 1/2" 3/8" 20.0 358.03
Gear Box T Series 47 Triplex Plunger Pumps with Gear Box for Gas Engines with 1" or 1-1/8” Shafts.
Drive Shaft Dia.: 1" Maximum Max. Max. FPT Ports
Part No. Pressure GPM RPM Shaft Inlet Outlet Wt. /Lbs. Net Ea.
IP T991GR 1500 3.5 3400 1" Hollow 1/2" 3/8" 24.0 $ 499.07
IP T9971GR 2000 3.5 3400 1" Hollow 1/2" 3/8" 24.0 599.07
IP TS1711GR 2700 3.5 3400 1" Hollow 1/2" 3/8" 45.0 609.24
D
IP TS1011GR 2000 4.0 3400 1" Hollow 1/2" 3/8" 45.0 596.48
IP TS1511GR 3000 4.0 3400 1" Hollow 1/2" 3/8" 45.0 616.47
IP TS2011GR 3000 4.0 3400 1" Hollow 1/2" 3/8" 45.0 678.23
IP TS1321GR 2100 4.75 3400 1" Hollow 1/2" 3/8" 45.0 606.18
IP TS1621GR 2500 4.75 3400 1" Hollow 1/2" 3/8" 45.0 678.23
1" & 1-1/8" IP TS2021GR 3500 5.6 3400 1" Hollow 1/2" 3/8" 45.0 645.02
Shaft Shaft Dia.: 1-1/8"
IP TS2011GR2 3000 4.0 3400 1-1/8" Hollow 1/2" 3/8" 45.0 $ 719.02
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0641
GENERAL High Pressure Pumps 179
D
HTF Models Shaft Wt.
HTS Part No. GPM Max. PSI RPM Size Lbs. Net Ea.
IP HTF2018S 4.0/5.0/7.5 3600 950/1200/1750 24mm 41 $ 1199.12
IP HTF2221S 8.5/10.2 3000 1450/1750 24mm 41 1229.13
HTF Series IP HTF2421S 10.0/12.0 3000/2500 1450/1750 24mm 41 1279.15
Designed for use in prep units, conveyor and multiple
gun applications. Excellent for carpet cleaning and HTW Models Shaft Wt.
for use in industrial plant systems where hot water Part No. GPM Max. PSI RPM Size Lbs. Net Ea.
is required. IP HTW3624S 18.0 1200 1000 35mm 57 $ 1550.15
IP HTCK3623S 21/25 1500/1300 1150/1350 30mm 80 2569.27
IP HTCK4050S 36 1500 800 30mm 157 3060.40
HTF
D
HTW HTCK
D
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0627
180 High Pressure Pumps
AR Plunger Pumps are designed for a wide variety of industrial cleaning, car/truck wash and
pressure wash applications. Available in pulley or direct drive for electric motor or gas engines.
Standard Features Include: High strength, forged brass manifolds • Aluminum oxide ceramic
plungers • Stainless steel valves, seats and springs • Continuously lubricated seals and V-packings
• Triple lip oil seals • Extra long connecting rods made from a special alloy • Die-cast aluminum
crankcases with oversized cooling fins • Premium bearings for exceptional load support • Maximum
140° F. • Ports on most pumps are 1/2” inlet by 3/8” outlet • Large flow pumps have larger ports •
D
Rails are not included and must be ordered separately if needed.
Direct Drive Motor Models Wt.
RSV Series Net Ea. Flow/Pressure RPM Lbs. Flange Shaft Net Ea.
AR RCA2G25E-F8 2.0 gpm @ 2500 psi 1750 11 56C 5/8" Hollow $ 213.00
AR XTA2G15EBA-F8 2.1 gpm @ 1800 psi 1750 10 56C 5/8" Hollow 273.50
AR RCA3G25E-F8 3.0 gpm @ 2500 psi 1750 11 56C 5/8" Hollow 213.00
AR RRA3G30E-F17 3.0 gpm @ 3000 psi 1750 18 182/184TC 1-1/8" Hollow 269.50
AR RRA4G30E-F17 4.0 gpm @ 3000 psi 1750 18 182/184TC 1-1/8" Hollow 269.50
AR RKA4G30E-F17 4.0 gpm @ 3000 psi 1750 21 182/184TC 1-1/8” Hollow 379.00
AR RCV2G25E-F8 2.0 gpm @ 2500 psi 3400 11 56C 5/8" Hollow 213.00
AR XTV2G15EBA-F8 2.1 gpm @ 1500 psi 3400 10 56C 5/8" Hollow 264.50
AR RCV3G25E-F8 3.0 gpm @ 2500 psi 3400 11 56C 5/8" Hollow 213.00
Direct Drive Gas Engine Models Wt.
Part No. Flow/Pressure RPM Lbs. Flange Shaft Net Ea.
AR XMV25G26D-F25 2.5 gpm @ 2600 psi 3400 15 Gas 3/4" Hollow $ 259.00
D AR RCV25G27D-F7 2.5 gpm @ 2700 psi 3400 11 Gas 3/4" Hollow 213.00
AR RMV25G30EZ 2.5 gpm @ 3000 psi 3400 8 Gas 3/4" Hollow 173.50
AR RCV3G25D-F7 3.0 gpm @ 2500 psi 3400 11 Gas 3/4" Hollow 213.00
AR XMV3G25D-F25 3.0 gpm @ 2500 psi 3400 15 Gas 3/4" Hollow 259.00
XWL Series AR RSV3G25D-F25 * 3.0 gpm @ 2500 psi 3400 14 Gas 3/4” Hollow 275.00
AR XMV3G30D-F24 3.0 gpm @ 3000 psi 3400 16 Gas 1" Hollow 269.00
AR RKV35G30ADF24 3.5 gpm @ 3000 psi 3400 21 Gas 1" Hollow 339.00
AR SXMV35G40DF24 3.5 gpm @ 4000 psi 3400 16 Gas 1" Hollow 295.00
AR RRV4G36D-F24 4.0 gpm @ 3600 psi 3400 18 Gas 1” Hollow 253.00
AR RSV4G40HDF40E * 4.0 gpm @ 4000 psi 3400 14 Gas 1” Hollow 299.00
* Includes Built-In Unloader Valve.
Pulley Drive Models Wt.
Part No. Flow/Pressure RPM Lbs. Flange Shaft Net Ea.
AR XT814N 2.1 gpm @ 2000 psi 1450 11 None 24mm $ 251.00
AR XTA2G15NBA 2.1 gpm @ 2000 psi 1750 10 None 24mm 251.00
AR RCA25G25N 2.5 gpm @ 2000 psi 1750 10 None 24mm 199.50
D AR XTA3G19N 3.0 gpm @ 1900 psi 1750 11 None 24mm 274.00
AR RCA3G25N 3.0 gpm @ 2500 psi 1750 10 None 24mm 199.50
AR RCA35G25N 3.5 gpm @ 2500 psi 1750 10 None 24mm 199.50
AR RRA4G30N 4.0 gpm @ 3000 psi 1750 17 None 24mm 259.00
AR RKA4G30AN 4.0 gpm @ 3000 psi 1750 19 None 24mm 323.00
AR RK1528HN 4.0 gpm @ 4000 psi 1450 22 None 24mm 375.00
RRA Series AR RKA4G40HN 4.0 gpm @ 4000 psi 1750 20 None 24mm 375.00
AR SHP1550N 4.0 gpm @ 7250 psi 1450 29 None 24mm 1249.00
AR RK1828HN 4.7 gpm @ 4000 psi 1450 20 None 24mm 379.00
AR XWM2128 5.5 gpm @ 4000 psi 1450 34 None 24mm 518.00
AR SXW2135 5.5 gpm @ 5100 psi 1450 35 None 24mm 676.00
AR SHP2250N 5.8 gpm @ 7250 psi 1450 29 None 24mm 1249.00
AR XWM2623 6.9 gpm @ 3600 psi 1450 34 None 24mm 569.00
AR SXWA7G50 7.0 gpm @ 5000 psi 1750 35 None 24mm 675.00
AR XW3025N 7.9 gpm @ 3600 psi 1450 34 None 24mm 599.00
AR RTP30.60N * 7.9 gpm @ 8700 psi 1000 177 None 35mm 5265.00
AR XWAM8G35N 8.0 gpm @ 3500 psi 1750 34 None 24mm 569.00
AR RTP38N * 10 gpm @ 7250 psi 1000 177 None 35mm 4335.00
AR XWL4121N 11 gpm @ 3000 psi 1450 34 None 24mm 699.00
D AR XWL50.15N 13 gpm @ 2200 psi 1450 34 None 24mm 699.00
AR RTJ70 * 18 gpm @ 4000 psi 1000 198 None 35mm 4895.00
AR RTF135N * 36 gpm @ 1500 psi 800 192 None 35mm 4895.00
AR 1836H Rail Kit, 1-1/2” High, XT Series........................................................ 15.75
AR 1837 Rail Kit, 5/8” High, RK, RKA, RKW Series....................................... 11.95
AR 2633 Rail Kit, 1-3/4” High, RC, RCA, RCV, RR, RRA Series.................... 15.90
RTF/RTJ Series AR 2633H Rail Kit, 2-5/8” High, RC, RCA, RCV, RK, RR, RRA Series............. 19.00
AR AR2748 Rail Kit, 1-1/4” High, RW, SXW, XW All, Series, 5 HP..................... 10.95
* Pumps have Built-In Feet that are Bolted to Baseplates.
Hydraulic Drive Pump/Motor Units
Part No. Pump Output Hydraulic Requirements Wt. Net Ea.
AR HYDRK1520 4 gpm @ 3000 psi 7.5 gpm @ 2500 psi 26 lbs. $ 699.00
AR HYDXW3010 8 gpm @ 1450 psi 9.5 gpm @ 1800 psi 43 lbs. 955.00
REPAIR KITS
Part No. Net Ea..
AR AR1828 Valve Kit, XRV/XRVC/GRKV/RKV..................................................... $ 30.40
AR AR1864 Valve Kit, XTA, XTV, HPE, XMV......................................................... 25.85
AR AR2780 Valve Kit, XW, WWA.......................................................................... 68.10
D
AR AR2864 Valve Kit, RK, RKA............................................................................ 31.75
AR AR1857 Packing Kit, XRV, XRA, RKV, RK....................................................... 59.30
AR AR1866 Packing Kit, XTA, XTV, HPE.............................................................. 45.70
AR AR2189 Packing Kit, RSV................................................................................ 32.85
AR AR2278 Packing Kit, XWM.............................................................................. 84.10
Hydraulic Units AR AR2741 Packing Kit, XMA, XMV, XM.............................................................. 47.35
AR AR2782 Packing Kit, XWA, 20mm................................................................... 67.75
AR AR2546 Plunger Kit, XRCA, XRCV................................................................. 99.10
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0289
Hypro High Pressure Pumps 181
1/2” FPT
Part No.
HY 5322C
Shaft
5/8"-Solid Rubber
Cups Wt.
10 lbs.
Net Ea.
$ 256.50
dultmeier.com
HY 5322CH 5/8"-Hollow Rubber 10 lbs. 256.50
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0291
182 HYPRO Plunger Pumps
from the ONLY American Manufacturer in the Industry
5-Year Warranty
Part No. Max. PSI Max. GPM Max. RPM Wt. Net Ea.
HY 2430B 3600 4.3 1725 35 lbs. $ 829.00
HY 2431B 3600 5.1 1725 35 lbs. 745.00
HY 2432B 3600 5.9 1725 35 lbs. 745.00
HY 2434B 2500 7.9 1725 35 lbs. 745.00
HY 2434B-C5 * 2500 7.9 1725 35 lbs. 899.00
Plunger Pump
Part No. Max. Flow Max. PSI Max. RPM Wt. Net Ea.
* Standard with rails to match “Cat 530” mounting.
HY 2535S 38 GPM 1500 800 140 lbs. $ 3308.00
HY 2545S 47 GPM 1200 800 140 lbs. 3463.00
Specifications: Inlet ports: Two 3/4" FPT • Outlet ports: Two 1/2" FPT
• Shaft rotation: CW or CCW • Shaft size: 1" solid • Oil type: 30 Wt. REPAIR KITS
non-detergent • Oil capacity: 26 oz. • Maximum water temperature: 160˚ F.
• Maximum water inlet pressure: 60 PSI.
Valve Kits
HY 2410B D
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0290
Comet High Pressure Plunger Pumps 183
High Quality Plunger Pumps from Comet. All Pumps Feature the following: Anodized, Die-Cast Aluminum Crankcase • Solid
Ceramic Plungers • Stainless Steel Check Valves and Piston Guides • Buna V-Packings • Reversible Crankcase Design for Right
or Left Hand Mounting • Designed for Direct Drive to Gas Engines or Electric Motors or with Solid Shafts for Belt Drive.
Solid Shaft
D
Plunger Pumps D
3.1 - 13 GPM
2000 to 5000 PSI
RW6030S
Part No. GPM PSI RPM Shaft Wt. Net Ea.
MV LWS-3020S 3.1 2000 1750 24 mm 13 lbs. $ 268.50
MV LWS-4020S 4.0 2000 1750 24 mm 13 lbs. 284.50
LWS3020S MV RWS5030S 5.0 3000 1750 24 mm 27 lbs. 426.00
MV RW5535S 5.5 3500 1450 24 mm 27 lbs. 458.50
MV RW6030S 6.2 3000 1450 24 mm 27 lbs. 416.00
MV TWN-6036S 6.0 3600 1000 24 mm 45 lbs. 710.00
MV TWN-8025S 8.0 2500 1000 24 mm 45 lbs. 710.00
MV TWS-10030S 10.7 3000 1750 24 mm 45 lbs. 755.00
MV TWS-13020S 13.0 2000 1750 24 mm 45 lbs. 788.00
MV RWS4040S 4.0 4000 1750 24 mm 27 lbs. 398.00
MV TW5050S 5.2 5000 1450 24 mm 45 lbs. 739.00
D
Gas Engine Drive with Flange
Plunger Pumps
2.1 - 4.0 GPM • 2000 to 4000 PSI
LWD3025G
Part No. GPM PSI RPM Shaft Wt. Net Ea.
MV LWD2020G 2.1 2000 3400 3/4” Hollow 13 lbs. $ 253.50
MV AXD3020G * 2.7 2000 3400 3/4” Hollow 12 lbs. 229.00
MV AXD2527G * 2.5 2500 3400 3/4” Hollow 12 lbs. 245.00
MV LWD3025G 3.0 2500 3400 3/4” Hollow 13 lbs. 263.50
D MV ZWD3035GK * 3.0 3000 3400 1” Hollow 17 lbs. 339.00
MV ZWD4035GK * 4.0 3000 3400 1” Hollow 18 lbs. 338.00
MV ZWD4040GK * 4.0 4000 3400 1” Hollow 18 lbs. 374.00
ZWD4030GK * Includes Unloader Valve & Chemical Injector.
with unloader
LWD3020E
Part No. GPM PSI RPM Shaft Wt. Net Ea.
MV AXD2020E * 1.90 2000 3400 5/8” Hollow 12 lbs. $ 233.50
MV LWD3020E 3.0 2000 3400 5/8” Hollow 13 lbs. 266.50
AXD2020E MV LWD3522E 3.5 2200 3400 5/8” Hollow 13 lbs. 322.50
with unloader
MV AXD2527GE * 2.5 2700 3400 3/4” Hollow 12 lbs. 255.00
MV LWD3522GE 3.5 2200 3400 3/4” Hollow 13 lbs. 322.50
* Includes Unloader Valve & Chemical Injector.
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0791
184 Plunger Pumps
Triplex Plunger Pumps from Giant Industries. Designed for pulley drive or direct-drive applications. Ideal for Car
Wash, Pressure Wash, Sewer Cleaning, Reverse Osmosis, Water Blasting and many more. All pumps feature a 5-Year
warranty in car wash and pressure wash applications. Lifetime warranty on manifolds due to erosion or freezing.
D
D
P56W P220A
Standard Features:
Forged crankshafts • Tapered roller bearings • Bronze connecting rods • Ceramic plungers • Brass
or Aluminum/Bronze fluid ends • Corrosion-resistant Hastelloy valves • Stainless steel and brass
wetted parts • Rated to 160° F. (or 195° F. as noted), higher temperature seals are availabale • Die
Cast Aluminum crankcases. (Note: Rail kits are shown, but must be ordered separately if needed.
Also, pumps have female NPT ports unless noted. BSP thread adapters are available if required).
Flows to 5-1/2 GPM
Part No. GPM PSI RPM Shaft Inlet Outlet **Rail Kit Wt. Net Ea.
D GU P205 0.5 2000 1750 24mm 1/2" 3/8" 1161 12 lbs. $ 352.00
GU P208 1.0 2000 1750 24mm 1/2” 3/8” 1161 12 lbs. 352.00
GU P209 1.5 2000 1750 24mm 1/2” 3/8” 1161 12 lbs. 352.00
SP100W GU P221 2.3 2000 1750 24mm 1/2” 3/8” 1161 12 lbs. 352.00
GU P221-30 † 2.3 2000 1750 24mm 1/2”BSP 3/8”BSP 1161 12 lbs. 538.00
GU P224 2.8 3000 1750 24mm 1/2” 3/8” 1161 12 lbs. 352.00
GU P223 3.0 2000 1750 24mm 1/2” 3/8” 1161 12 lbs. 352.00
GU P218A 3.4 2500 1750 24mm 1/2” 3/8” 1161 12 lbs. 352.00
GU P340 3.5 4000 1750 24mm 1/2” 3/8” 1161 16 lbs. 437.00
GU P313 3.8 3500 3450 24mm 1/2” 3/8” 1161 16 lbs. 375.00
GU P460 3.8 7250 1450 28mm 1/2” 3/8” 7358 37 lbs. 2366.00
GU P46W * 3.9 2175 1420 18mm 1/2” BSP 3/8” BSP 1075 16 lbs. 495.00
GU P219 4.2 2500 1750 24mm 1/2” 3/8” 1161 12 lbs. 352.00
GU P219-30 † 4.2 2000 1750 24mm 1/2”BSP 3/8”BSP 1161 12 lbs. 538.00
GU P54W * 4.5 4000 1450 24mm 1/2” BSP 3/8” BSP 1075 18 lbs. 719.00
GU P220A 4.7 2000 1750 24mm 1/2” 3/8” 1161 12 lbs. 352.00
D
GU P316 4.7 3000 1750 24mm 1/2” 3/8” 1161 16 lbs. 375.00
LP301A GU P317 4.8 3000 1750 24mm 1/2” 3/8” 1161 16 lbs. 375.00
GU P55W * 4.9 2300 1420 24mm 1/2” BSP 3/8” BSP 1075 18 lbs. 595.00
GU P322 5.0 3000 1750 24mm 1/2” 3/8” 1161 16 lbs. 385.00
GU P58W * 5.0 3500 1450 24mm 1/2” BSP 3/8” BSP 1075 19 lbs. 696.00
GU P325 5.2 3500 3450 24mm 1/2” 3/8” 1161 16 lbs. 375.00
GU P485 * 5.3 7250 1450 28mm 1/2” BSP 3/8” BSP 7358 42 lbs. 1998.00
GU P318 5.5 2000 1450 24mm 1/2” 3/8” 1161 16 lbs. 442.50
GU P455A 5.5 5000 1450 28mm 1/2” 3/8” 7358 37 lbs. 1149.00
Flows Over 6 GPM
Giant Part No.
GU P56W
GPM
6.1 1900
PSI RPM
1420 24mm
Shaft
1/2"
Inlet
3/8"
Outlet
1075
**Rail Kit Wt.
18 lbs.
Net Ea.
$ 598.00
Pump Oil GU P435
GU P59
6.6
7.5
3625
1900
1450 28mm
1450 24mm
3/4”
1/2”
1/2”
3/8”
7358
1075
37 lbs.
19 lbs.
1170.00
736.00
GU LP700 7.9 7250 1000 35mm 3/4” 1/2” 7357 116 lbs. 6796.00
GU P423R 8.3 2600 1450 28mm 1” 3/4” 7358 37 lbs. 1140.00
D
GU SP200W 9.6 2175 1420 28mm 3/4” 3/8” 7358 42 lbs. 1735.00
GU LP600 * 9.7 6000 1000 35mm 1-1/4” BSP 1” BSP 7357 110 lbs. 4120.00
GU P422R 10 2000 1450 28mm 1” 3/4” 7357 37 lbs. 1125.00
GU SP100W 11 1900 1420 28mm 3/4” 1/2” 7358 31 lbs. 1235.00
GU MP4124 13 2600 1420 28mm 1” 3/4” 7358 72 lbs. 2525.00
GU P420A 13 1700 1460 28mm 1” 3/4” 7357 37 lbs. 1129.00
D
GU GP6124 13 5800 800 42mm 1-1/2” 1” Included 309 lbs. 9495.00
GU LP301A * 14 4000 1000 35mm 1-1/4” BSP 1” BSP 7357 110 lbs. 3798.00
GU P470 * 18 1000 1450 30mm 1” BSP 3/4” BSP 7358 39 lbs. 1541.00
GU LP200 20 2900 1000 35mm 1-1/2” BSP 1” BSP 7357 112 lbs. 3898.00
Special blend crankcase oil/lubricants for Giant GU LP123A 35 1300 800 35mm 1-1/2” 1” 7357 116 lbs. 3250.00
Pumps. ** Rail kits not included.
* BSP is British Pipe Thread, adapters to NPT thread are available if needed.
Model 1060-32 is for use in GX/HR/P200/P300/P400 † Rated to 195° F.
and SP Series pumps and is sold in 32 oz. bottles.
Model 1154 is a different oil blend and is for use in SERVICE & REPAIRS
MP/LP/GP Pumps, sold in 1 gallon containers. RAIL KITS Did you know? We can
Part No. Net Ea. service almost every brand
Part No. Size Net Ea. GU 1075 Rail Kit....................... $ 21.75 of pump we sell in our catalog.
GU 1060-32 32 oz. $ 10.25 GU 1161 Rail Kit....................... 22.65 Call us at 1-800-228-9666
GU 7357 Rail Kit....................... 67.20 (Omaha, NE) for a quote!
GU 1154 1 Gallon 41.75
GU 7358 Rail Kit....................... 26.70
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0292
Jetting & Sewer Cleaning Pumps 185
High flow, high pressure pumps are the ideal choice for pipe cleaning, water jetting, sewer cleaning, hydrostatic testing, tank cleanout
and plant washdown. Pumps from Cat Pumps®, General and Giant Industries. All plunger pumps shown feature brass, stainless,
aluminum/bronze or nickel-plated manifolds as noted. Triplex ceramic plunger design. Pressure and safety relief valves as well as
pulsating valves are available for many models. (Note: All pumps are standard with Right Hand shaft when facing pump manifold
or some feature dual shaft design. Left hand models are also available).
GU LP200
Left Hand Shown
D
CC 2510
KE Series
Right Hand Shown
CC 3560
GU GP7255A
Dual Shaft
Dual Shaft
Part No. Flow Pressure RPM Brand Manifold Wt. Net Ea.
CC 1560 8 4000 1140 Cat Pumps® Brass 60 lbs. $ 2257.00
CC 660 10 3000 1430 Cat Pumps® Bronze 44 lbs. 2025.00
IP KE22A 10 3600 1450 General 420SS 88 lbs. 3295.31
IP KE24A 12 3000 1450 General 420SS 88 lbs. 3298.32
GU MP4124 12 3000 1420 Giant Alum/Bronze 72 lbs. 2525.00
UD NX55/200 14 3000 1450 Udor Brass 75 lbs. 2485.00
CC 3517 14 3600 800 Cat Pumps® Nickel/Bronze 152 lbs. 5973.00
GU LP301A 14 4000 1270 Giant Alum/Bronze 110 lbs. 3798.00
GU LP400 15 3600 1000 Giant Alum/Bronze 105 lbs. 3356.00
IP KE28A 16 2200 1450 General 420SS 88 lbs. 3295.31
AR RTJ70 18.5 4000 1000 AR Brass 198 lbs. 4895.00
CC 2510 20 2000 1450 Cat Pumps® Brass 80 lbs. 3416.00
UD NX75/150 20 2200 1450 Udor Brass 75 lbs. 2485.00
GU LP200 20 2900 1000 Giant Alum/Bronze 119 lbs. 3898.00
CC 3560 20 4000 1160 Cat Pumps® Brass/Stainless 145 lbs. 5695.00
IP HF25A 20 4000 1000 General 420SS 132 lbs. 5252.11
GU LP255 26 2200 950 Giant Brass 119 lbs. 3245.00
IP KS28A 30 3600 1500 General Nickel/Cast 212 lbs. 8545.79
UD VX130/160 33 2500 1000 Udor Brass 160 lbs. 3840.00 SERVICE & REPAIRS
IP KF36A 40 1900 1000 General 420SS 220 lbs. 4495.76
Did you know? We can
GU LP123A 40 2000 885 Giant Alum/Bronze 116 lbs. 3250.00
UD VX160/130 40 2000 1000 Udor Brass 160 lbs. 3840.00 service almost every
IP MSS40 44 3900 750 General Nickel/Cast 570 lbs. 11100.20 brand of pump we sell
IP MSS45 56 3000 750 General Nickel/Cast 570 lbs. 11100.20 in our catalog.
CC 6760 60 1200 520 Cat Pumps® Brass 335 lbs. 12305.00
CC 6775 75 1200 520 Cat Pumps® Brass 335 lbs. 14573.00 Call us at 1-800-228-9666
IP MSS50 69 2500 750 General Nickel/Cast 570 lbs. 11100.20 (Omaha, NE) for a quote!
GU GP7255A 80 2000 850 Giant Nickel/Cast 375 lbs. 8198.00
IP MK60A 90 2500 1500 General Nickel/Cast 862 lbs. 15390.60
IP MK65A 107 2200 1500 General Nickel/Cast 862 lbs. 15391.93
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0868
186 Circulator Pumps
TACO Circulator Pump/Motor Units are designed to circulate heated or chilled
solutions in commercial or residential Heating & Air Conditioning Systems as Circulator Pumps
well as Cooling towers, Booster service and Recirculation. Available in either
Series UP Cast Iron Circulator Pumps
cast iron, bronze or stainless as noted. Flanges can be ordered separately to
are specifically designed for Closed Loop,
accommodate a wide variety of plumbing sizes if required.
Heating Systems. Ideal for use with Boiler/
Hydronic Systems, Heat Pumps, Radiant
“00” Series Floor Heat and Solar Heating. Motors are
115 volt, single phase.
Pump Units Features: Pumps are single speed • Working
Standard Features Include: pressures to 145 PSI • Maximum temperatures
Unique replaceable cartridge to 230° F. • Maintenance-Free • Low noise output
• Low energy design. Note: Pump units do not D
is field serviceable • Self-Lubri-
include flanges which are shown separately. (Model
cating bearings • Quiet, efficient UP26-99F has higher PSI output than UP26-64F).
operation • High capacity output,
compact design • Universal
Part No. Description HP Max. Flow Wt. Net Ea.
Flange mounts • Direct drive
BL UP15-10F Circulator Pump 1/25 8 GPM 7 lbs. $ 121.50
design • Low power consumption
BL UP26-64F Circulator Pump 1/12 32 GPM 11 lbs. 291.50
• Cast Iron or Stainless casings D
BL UP26-99F Circulator Pump 1/6 28 GPM 12 lbs. 306.00
• Non-Metallic impeller, Ceramic
BL 519601 * 3/4” Flange Set.............................. 2 lbs. 9.99
shaft, Carbon bearings • Pres-
BL 519602 * 1” Flange Set.............................. 2 lbs. 9.99
sures to 125 psi • Temperatures
BL 519603 1-1/4” Flange Set.............................. 2 lbs. 9.99
to 220° F. • Motors are 115 volt,
BL 519604 * 1-1/2” Flange Set.............................. 2 lbs. 9.99
60Hz, Single Phase. UL and CSA
* These flanges fit UP15 & UP26 Series Only.
listed. 3250 RPM.
“00” Series Pump Units (less flanges) VersaFlo Cast Iron, In-line Circulator Pumps
for Stationary Open or Closed Heating and
Part No. Construction HP Flow Head Wt. Net Ea. Cooling Systems. Also a good choice for use
HU 007F5 Cast Iron 1/25 0-20 GPM 0-11 ft. 8 lbs. $ 84.95 in Floor Heat or Snow Melt Systems.
HU 007SF5 Stainless 1/25 0-20 GPM 0-11 ft. 8 lbs. 239.00
Features: Motors are 115 or 230 volt, single phase (3
HU 009F5 Cast Iron 1/8 0-8 GPM 0-34 ft. 9.5 lbs. 225.00 phase also available) • Pumps are multi-speed, wet
HU 009SF5 Stainless 1/8 0-8 GPM 0-34 ft. 10 lbs. 310.00 rotor design • Pressures to 145 PSI • Temperatures
HU 0011F4 Cast Iron 1/8 0-28 GPM 0-30 ft. 12 lbs. 222.50 D
to 230° F. • Maintenance-Free motors with thermal
HU 0011SF4 Stainless 1/8 0-28 GPM 0-30 ft. 12.5 lbs. 339.00 protection are standard. Note: Flanges are not
included, but can be ordered separately.
“100” Series Pump Units Part No. Description HP Volts Wt. Net Ea.
BL UPS32-802 Circulator Pump 1/2 115 38 lbs. $ 732.00
Standard Features BL UPS32-803 Circulator Pump 1/2 230 37 lbs. 732.00
Include: Resilient BL UPS32-162 Circulator Pump 3/4 115 42 lbs. 969.00
mounted, split BL UPS32-163 Circulator Pump 3/4 230 44 lbs. 969.00
phase motors BL UPS50-162 Circulator Pump 1-1/2 230 67 lbs. 1425.00
with built-in
overload • One-
piece balanced “1600” Series Pump Units
impeller • D
Standard Features Include: Flows from 10 gpm to 235 gpm with head
Stainless steel capacities to 50' • Permanently lubricated bearing cartridge isolates bearing
shaft • Rugged from system temperature • Balanced cast bronze impeller assures long
bronze sleeve bearing life • Corrosion resistant shaft sleeve • Standard mechanical seals for
• Carbon/ceramic seal assembly • One-piece Flange Sets for added flexibility • Resilient mounted motors insure quiet reliable operation
spring coupling • Factory tested prior to shipment • 00 & 100 Series
• Pressures to 175 psi and temperatures to
Easy, low cost servicing, no special tools required • 250° F. • Cast Iron Casing and flanges • Alloy
Maximum temperatures to 240° F. intermittent and steel shaft • Motors are single phase, ODP.
200° F. continuous • Maximum pressures to 125 psi (Three phase also available).
• Motors are 115 volt, 60Hz, Single phase.
Flange Sets for 00 & 100 Series Pump Units “1600” Series Pump Units (with flanges)
Part No. FPT Flanges HP Flow Head Wt. Net Ea.
Part No. Construction Wt. Net Ea.
HU 1600C 1-1/2" 1/4 0-55 GPM 0-20 ft. 59 lbs. $ 654.00
HU 110-251 3/4" Cast Iron Flange Set......... 2 lbs. $ 9.44
HU 1610C 1-1/2" 1/3 0-71 GPM 0-23 ft. 62 lbs. 705.00
HU 110-252 1" Cast Iron Flange Set............ 2 lbs. 9.44
HU 1612C 1-1/2" 1/2 0-55 GPM 0-35 ft. 89 lbs. 899.00
HU 110-253 1-1/4" Cast Iron Flange Set...... 2 lbs. 9.44
HU 1614C 1-1/2" 3/4 0-70 GPM 0-45 ft. 91 lbs. 976.00
HU 110-251B 3/4" Bronze Flange Set............ 3 lbs. 28.85
HU 1634C 2" 1 0-170 GPM 0-38 ft. 100 lbs. 1187.00
HU 110-252B 1" Bronze Flange Set............... 3 lbs. 28.00
HU 1636C 2” 1-1/2 0-190 GPM 0-40 ft. 125 lbs. 1475.00
HU 110-253B 1-1/4" Bronze Flange Set......... 3 lbs. 28.00
HU 1638C 2" 2 0-200 GPM 0-50 ft. 153 lbs. 1449.00
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0281
High Pressure Pump Units • Generators 193
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0296
194 Pressure Washers
12-Volt Pressure Washer Hydraulic Pressure Washers
12-Volt Portable Pressure Washer on Hand Carry Cart. Continuous duty, sealed These hydraulically-driven pressure
motor. On-off switch with circuit breaker. Unloader valve, 25’ high pressure hose, washers are designed for remote and
quick connect fittings, spray gun and chemical injector. 15’ Battery cables with heavy explosion-proof environments where
duty clamps are also included. electricity cannot be used. The ideal
D choice for use with washdown and
cleaning of construction equipment,
agricultural equipment, concrete
cleanup, etc.
Part No. GPM PSI Amp Draw Wt. Net Ea.
PX 80391 1.4 700 65 60 lbs. $ 1198.00 Wand & Hose are included in
some kitsπ
Kits are complete with hydraulic motor, HYPRO plunger pump, mounting
12-Volt Pressure Washer Kits rails, unloader valve, pressure gauge and quick disconnect for hose. Some
models come with spray wand and 50’ hose as shown. A wide variety of
Compact 12-Volt Pressure Washer Kits are simple, fast, quiet and reliable. Sealed
flows and pressures are available to meet your needs. Ports are 1/2” FPT
motors with push/pull switch and circuit breaker. All kits include unloader valve,
spray wand, 25’ spray hose, suction filter and inlet hose, chemical injector and motor
x 3/4” FGHT inlet and 3/8” male quick disconnect. Rated to 160° F.
mounts. Can be easily mounted to your equipment frame. Hydraulic Motor
Part No. Cleaning Capacity Requirements Wt. Net Ea.
HY 1803C 3.0 GPM @ 1000 PSI 5 GPM @ 1000 PSI 28 lbs. $ 956.00
PWK15 HY 1805C 3.0 GPM @ 1500 PSI 8 GPM @ 1900 PSI 28 lbs. 1010.00
HY 1807C 3.0 GPM @ 2000 PSI 11 GPM @ 1300 PSI 28 lbs. 1118.00
HY 1827C 4.0 GPM @ 2000 PSI 8 GPM @ 2000 PSI 33 lbs. 1154.00
Note: These models do not include hose & wand assembly.
D Hydraulic Motor
Part No. Cleaning Capacity Requirements Wt. Net Ea.
HY 1802 3.0 GPM @ 1000 PSI 5 GPM @ 1300 PSI 38 lbs. $ 1121.00
HY 1804 3.0 GPM @ 1500 PSI 8 GPM @ 1900 PSI 41 lbs. 1175.00
HY 1806 3.0 GPM @ 2000 PSI 11 GPM @ 1300 PSI 41 lbs. 1282.00
HY 1826 4.0 GPM @ 2000 PSI 8 GPM @ 2000 PSI 49 lbs. 1319.00
Part No. GPM PSI Amp Draw Wt. Net Ea. Note: These models also include spray wand & 50’ hose assembly.
PX PWK15 1.0 200 15 20 lbs. $ 429.00
PX PWK71 1.4 700 65 55 lbs. 1065.00
50 ft. Hose
D
D
MD4030SH
Wand D
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0908
Water Garden/Pond Pumps & Filters 199
PE1FPW
D
Rotor Type D
D
Pump Max.
Part No. Type Flow Rate Lift Discharge Wt. Net Ea.
GJ PE1FPW Rotor 170 gph 7' 1/4" MPT 4 lbs. $ 50.73 D
566102 566154
GJ PE2FPW Rotor 300 gph 12' 1/4" MPT 5 lbs. 71.86 Mechanical Filter Biological Filter
GJ PE25FPW Rotor 475 gph 13.5' 1/2" MPT 6 lbs. 89.93
GJ PES300PW Mag Drive 325 gph 10' 1/2" MPT 5 lbs. 45.51
GJ PES500PW Mag Drive 500 gph 10' 1/2" MPT 5 lbs. 73.62 Model 566102 is a mechanical filter that features easy-to-clean filter pads.
GJ PES700PW Mag Drive 665 gph 11.5' 1/2" MPT 5 lbs. 63.33 Standard with 6" stem with adapter for use with fountain heads. For use with
Note: 5% Additional Discount for purchase of 3 or more pumps of one size.
PE and PES pumps shown at left of page. Pumps fit into filter basin.
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0630
200 Water Fountain Pump Systems
Water Fountain Systems are an ideal choice for use in waterscapes, private ponds, industrial centers, golf courses or city parks. Systems
are complete and ready for hookup. Lighting kits are available as an option.
Pumps will operate in as little as 5 ft. of water. Designed with stainless eye bolts for anchoring to pond bottom or shore line. 100’ power
cords are standard but additional power cables in 50 ft. increments with heat shrink splicers are available. (Note: 250 ft. maximum cord
length from pump to control panel). Three different motor sizes allow for a wide range of height and flow rates to meet your needs.
All fountain units include three interchangeable nozzles for optional spray patterns. (Note: Fountain units are not approved or tested for
use in swimming areas).
Model FPS0501 is a 115 volt, 1 phase unit and includes pump, 100 ft. power cord and GFI plug.
Model FPS 230 Volt, 1 Phase Units include pump, 100 ft. of cable and weather-proof control panel.
Control panels are lockable and include a GFI and 24 hour timer.
Model 023069 120 Volt Light Kit is an option for all 230 volt fountain units. Includes (3) 35
watt, clear halogen lamps for night lighting. Also includes 100 ft. of power cord and stainless
mounting brackets. On/Off settings are controlled through the timer in the 230 volt control panels.
(NOTE: This kit will not work with FPS0501 115 volt fountain).
D
Models
• FPS05021
• FPS07021
023069 Light Kit • FPS10021 D
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0836
Metering & Automation Systems 203
Pump Starter
D
Panel Assembly
For 12V Mini-Bulk Pumps
Allows automated operation of 12V mini-
bulk pumps. Used in conjunction with NTEP
FDSMT150 chemical measuring tank systems. Panels
150 Gallons D available to control 2-6 pumps. Specify 10 to
Sizes Available 50 Amp Power Supply (sold separately).
150 Gallon Tank Assembly. with deep slope
260 Gallon Tank Assembly. with deep slope Call for System Pricing
90 Gallon Stainless Tank Assembly for platform scale
D 130 Gallon Stainless Tank Assembly for platform scale
250 Gallon Stainless Tank Assembly for platform scale
5 HP, 3 Phase Pump Assembly 120 Volt AC to
FDSMT170
170 Gallons
Please Call for System Pricing 12 Volt DC
Power Supply
Tank Level Monitor/Inventory Converter
Control System D
Pressure
Sensor Part No. Description Net Ea.
Probe
KC 585021 7 Amp Power Supply......... $ 137.00
KC 585022 10 Amp Power Supply....... 206.00
KC 585025 25 Amp Power Supply....... 436.00
KC 585026 40 Amp Power Supply....... 566.00
KC 585027 50 Amp Power Supply....... 650.00
D
Control
Panel
D Uninterruptible
Junction Box Power Supply (UPS)
FEATURES:
• Standard System Monitors Up to 8 Tanks. • 128 Tank Capability
• For Liquid or Dry Material • Printed Reports at User Set Times • Units Use to protect computers, printers, modems,
control panels and other sensitive equipment
are Capable of being Monitored Via a Network or Modem • Variety of
from power surges, brownouts, etc. Powered
Probes Available for Customer Specific Needs • Printer Sold Separately by 120VAC with grounded plug. Includes
(6) equipment plug outlets (3 battery/surge
Please Call for System Pricing and 3 surge only) and USB port. Built in
jack for Telephone/DSL/Ethernet protection.
D
Automatic voltage regulation (stabilizes
incoming power). 750VA Rating.
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0304
391
Chemical Injectors
6350 Pulse Pump ChemFlex Injectors
Pulse Pump from Cat Pumps® permits chemical injection at pressures Innovative Chemical Injectors for use with
up to 3000 PSI. Mounts on the center inlet port of many Cat Pumps® Automatics, Self-Serve Systems and even
and is activated with each stroke of the pump. Includes a prime bulb to pressure washers applications. 3/8” MPT
start chemical. Requires correct 76400 series adapter for specific Cat stainless steel inlet and outlet ports and PVDF/
Pumps® models. Kynar injection bodies with Teflon o-rings,
ensure the highest chemical and corrosion
resistance available. Note: 120083 features
D
EPDM O-ring.
Color coded and clearly marked for a wide variety of flow ranges. Available with
single, double and triple chemical barbs for injection of more than one chemical at
the same time. Slip-in replacement for injectors used on most of the common high
pressure automatics in the car wash industry. Chemical barbs are 1/4” and are
standard with internal threads to accept a wide range of orifice tips, (sold separately).
Rated to 1000 PSI and 175° F.
D Shown
Mounted on Part No. Color Nozzle
Cat Pump
Threaded fitting to allow for
installation of metering tips 110057 0.057 in.
Barb Fitting
1500 PSI. Designed to mount to the replacements in many common Automatics such
D
valve port of many different General as PDQ Systems. Injectors are stainless steel
Pump models. Construction is construction with
303 Stainless Steel with Buna 3/8" MPT inlet and outlet. Chemical barbs are D
PUMP ADAPTER VALVE diaphragm. Inlet and outlet are 1/4" hose barb with internal threads for "screw
SERIES FITTING ASSEMBLY 1/8” FPT, pulse port is 1/4” FPT. in" metering tips, (not included). Available in single barb
60 (TC) 520222 103036 To convert existing pumps, one or dual barb models.
44 (EZ) 520197 103036 Part No. Orifice Barbs Net Ea.
adapter and one valve assembly
63 (TX) 520197 103036 Dual Barb IP 100336 .057 1 $ 25.95
47 520190 103035 is also required from the chart No. 100541 IP 100835 .070 1 36.96
66 (TSF) 520223 103090 shown. IP 100334 .083 1 25.95
D IP 100333 .086 1 25.95
Maximum Maximum IP 100339 .098 1 25.95
Part No. Pressure Flow Net Ea. IP 100541 .083 2 51.96
DE 100-15K Tip Kit, Standard...... 6.75
IP 100906 Pulse Pump 1500 PSI .75 GPM $ 231.79 DE 100-15KU Tip Kit, Ultra Lean.... 3.96
IP 100464 Repair Kit................. 16.47
Viton® is a registered trademark of DuPont Performance Elastomers
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0780
394
Pumps • Switches • Solenoids
FUEL PUMPS
Oil Burner Pumps from Suntec. High Pressure D
Suitable for use with kerosene, No. 1
or No. 2 Fuel Oil. (Waste Oil Pumps Flow Switches 4’ Cord
also available). Pumps are designed
to be gravity fed fuel oil from your ST5 Flow Switch. Easy-to-install. Must be mounted in vertical position. Minimum
holding tank and to then pressurize pressure is 75 PSI and maximum pressure is 3600 PSI. Minimum flow is 1 GPM and
the fuel to a nozzle. Maximum flow is 8 GPM. Maximum temperature is 167° F. Inlet and outlet ports are
3/8" FPT. Standard with 250V, 3-amp Reed switch for burner shut-down.
Single-stage pumps are for medium ST6 Switch. Same specifications as
lift applications and can be mounted ST5 but has 3/8" MPT inlet and
in any position. Two-stage pumps are D
outlet and 1/4" gauge port. It can
for high lift, long run applications and be mounted in either vertical or D
can be mounted in any position except horizontal position.
upside-down. All pumps are factory
No. A2VA-7116
set at 100 PSI but are adjustable from
ST505 Switch.
100-150 PSI. Rated to 7300 Part No. Net Ea.
PSI, 176° F. and
Available in 1725 RPM or 3450 RPM NP ST5 Flow Switch....................... $ 26.95
8 GPM. 3/8" FPT
models. *Shaft rotation and nozzle inlet and 3/8" MPT NP ST6 Flow Switch....................... 27.95
port location is either RH or LH as outlet. Housing is NP ST505 Flow Switch . .................... 82.25
viewed from the shaft end. stainless steel. NP 200005455 Reed Switch Only, ST5..... 13.35
NP 200006550 Reed Switch Only, ST6..... 13.35
D
Many Other Models
Available! Flow Switches
No. J4NB-A1000G FS8
Model FS8 Flow Switch is rated to 3600 PSI
* Rotation & Pump and up to 8 GPM. Electrical ratings to 230 volt,
Part No. RPM Nozzle Port Type GPH Net Ea. 3 amp. Ports are 3/8" MPT. Must be mounted in D
SD A2VA-7116 3450 RH/RH 1-Stage 3 $ 53.95 vertical position to function properly. Maximum
SD A1YA-7912 1725 RH/RH 1-Stage 7 61.95 temperatures to 175° F.
SD B1VA-8212 1725 RH/RH 2-Stage 3 139.50 Model 100975 Flow switch is rated to 12 gpm and
SD J4NB-A1000G 1725 RH/LH 1-Stage 26 203.00 5000 psi. Can be mounted in any direction. (3) 100975
* As viewed from shaft end. magnet design means shuttle will not stick. Rated
to 5 amp and 250 volt. Ports are 3/8" FPT. Maximum
temperatures to 180° F.
D
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0602
CORKEN ® NH3/LPG Pumps & Compressors 409
Coro-Vane® Pumps
for LPG & NH3
CORKEN ® base mounted pumps are complete with base, V belt drive assembly and
beltguard, 3 PH TEFC motor. Pumps are standard with FPT bolt-on flanges. Use 1-1/4"
“Z” Series Pumps for NH3 / LPG
relief valve on 521/522 pumps; 2" on 1021/1022 pumps. For Stationary Plant & Truck Use
Coro-Vane is a positive displacement pump line that is designed for stationary
®
The Z3500 Pump offers higher flow rates (177 GPM at 780 RPM & 50 PSI
applications at bulk plants. differential pressure) than the Corken 1021 series. Design features include
• Only CORKEN Coro-Vane pumps have heavy duty roller bearings for longer service
® ®
reversible sideplates, improved cam design to reduce cavitation and improve
life. The bearings are interchangeable in all sizes of Coro-Vane® pumps. efficiency, patented needle roller thrust bearings to minimize side plate wear.
• All parts, including the hydraulically self-adjusting blades, are easily accessible for Maintenance is also simple: simply remove twelve head bolts to inspect
inspection or replacement without disturbing the piping. the bearings, seals, sideplates, rotor, vanes & vane drivers. Rated to 800
• Models 521 and 1021 have a built-in internal relief valve (external relief valve still RPM. Retrofits easily to replace the Corken 1021 and other 3” vane pumps
recommended). with little or no change in piping.
• Bottom FPT flanges of ductile iron save money by eliminating pipe unions and also Ductile iron body, gray iron cam & sideplates; steel shaft, bearings & relief
simplify installation. Steel slip on welding flanges also available. valve; Buna-N O-rings. Z4500 provided even higher flow rates (382 GPM
SPECIFICATIONS: @ 780 RPM).
RPM: 420 - 950
Temperature:
-25˚F to 225˚F
Connections:
521: 2” x 2”
1021: 3” x 3”
Working
Pressure:
D 125 PSI
ST 1021EG
Compressor Unit
for NH3
Standard Features:
• Pressure Gauges • Interconnecting Piping
• Steel Baseplate • Adjustable Driver-Slide-Base
• Mechanical Liquid Trap • V-Belt Drive & Beltguard
• Four-Way Valve • TEFC Motors
• Strainer
This standard unit is typically used for liquid transfer and vapor recovery in
applications including rail car unloading. D
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0454
Remote Fuel Pumps - Cabinet Mount 447
Standard Features:
• Rain-Proof Cast Iron Pump Housing: Iron Motor
• Explosion-Proof UL/cUL Listed Motors
• Motors have Sealed Bearings, Heavy-Duty Switch and Thermal Overload Protection
• Built-In Junction Box
• Integral Check Valve, Pressure Relief Valve and Strainer Assembly (No foot Valve Required)
Model FR713
• Automatic Bypass Valve, Anti-Siphon Device, Tank Adapter, Fittings and Anti-Siphon Pipe
• 2” MPT Base to Fit Standard Tank Openings
• 115/230 Volt Motors Standard
FILL-RITE
Model 303/313
FILL-RITE Compact Cabinet Pump Units for Above Ground Storage Tanks
These “Cabinet” Style Pump/Meter Units are specifically designed for Above Ground Storage Tanks (AST’s)
Standard Features:
• Rain-Proof Cabinet includes Pump & Meter - 18 GPM
• 1/3 HP Explosion-Proof UL/cUL Listed Motors
• Motors have Heavy-Duty Switch, Thermal Overload & Junction Box
• 800C Meter with Mechanical Totalizer
• Integral Check Valve (No foot Valve Required)
• 3/4” x 12’ Hose, Standard Manual Nozzle (Automatic Nozzle available), Standard Nozzle
Boot, Rear Discharge
• 2” MPT Base to Fit Standard Tank Openings
• 115 Volt Motors Standard; 220 Volt Available
• Conversion Kits Available for B20-B100 Biodiesel & E-85 Ethanol and Vapor Recovery Model
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0754
448 Fuel Pumps
Standard Pumps will Handle E10 & B20 Fuels. Any Mixtures Higher than This See Adjacent Page for Conversion Kits
Fill-Rite fuel transfer pumps and meters are currently designed All meters
to handle a maximum blend ratio of 1-20% biodiesel fuel.These
mixtures of fuels are known as B1-B20. Conversion kits are Fuel Pump are of the
time-proven
nutating disc
available to make Fill-Rite pumps compatible with biodiesel Heavy Duty - Red type. All have
blend ratios from above 20% (B20) all the way up to the 100% - 115-Volt - wheel-type
registers
concentrate (B100) and also for E85 fuel. (see next page). Also 18 GPM with large
see “BD” Models for B21-B100. D easy reading
- 2 Year Warranty - numerals.
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0276
Fuel Pumps • Repair Kits 449
Standard Pumps will Handle E10 & B20 Fuels. Any Mixtures Higher Than This See Conversion Kits Below
RE
PA
Rotary Vane Pumps
115/230VOLT IR
Om Avai SERV 12 Volt & 115 Volt
aha labl IC
Electric Fuel Pump Units & D e in E
ave
npo
Heavy Duty - Red - 2 Year Warranty rt Economical pumps for light duty transferring of diesel, anti-freeze, transmission
fluid & light oils. Self-priming. 3/4” FNPT inlet & outlet on 12 Volt models; 1” x 1”
SERIES 300 MODELS - 30 GPM
on 115 Volt models. Cast iron bodies, iron rotors, HNBR seals. Internal by-pass
NOT FOR GASOLINE. DIESEL FUEL ONLY.
valve and battery cable with alligator clips included. Pump “Kits” also include
Pumping Units are positive displacement rotary type with eight self-adjusting vanes. 3/4”, 8’ suction hose with foot
Valve, strainer Assembly and By-Pass Valve are equipped with Viton® seats. Meter is valve & 3/4” x 8’ discharge
of nutating disc type providing accuracy adjustment for field calibration. Registers to
999 gallons in 10ths of a gallon. Nozzle boot provides secure fastening and locking of hose with 3/4” poly nozzle
nozzle when not in use. Pump can be used in skid tank, island or underground tank (1” on 115 Volt models).
applications as well as with a pedestal. Pump inlet is 2" MNPT. 2” x 1-1/2” Tank adapter 12 Volt models flow
included. Suction Pipe is not included. diesel at 10 GPM
(at 9.5 PSI). 115
NP311
NP310 Volt models flow
diesel at 18 GPM
FR1612
(at 12 PSI).
D
D
All models are rated for 30 minute duty cycle. 12 Volt models include 30
amp fuse. 115 Volt models include a 6-1/2’ power cord. Temperature rating:
0-100° F. Not for gasoline or other flammable liquids or water (not UL listed).
Part No. SERIES 300 ELECTRIC PUMPS WT. Net Ea. FR1614
FR NP310 30-GPM Pump. Less Meter................. 79 lbs. $ 954.27
FR BD310 * 30 GPM Biodiesel Pump Less Meter - 1019.34
FR 901MK300 Meter Kit with fittings to add meter..... - 227.82
FR NP311 30-GPM Pump with Meter.................. 86 lbs. 1182.00
FR BD901CMK * Meter Kit for Biodiesel...................... - 267.53
DU 1-1/4X48 1-1/4’X48” Suction Pipe...................... - 20.75 Part No. Description Ports Voltage Amp Draw Kit Net Ea.
* Use for B21-B100 Biodiesel Only. FR FR1612 12V Rotary Pump 3/4” 12 Volt 20 Amps No $ 113.37
FR FR1614 12V Rotary Pump “Kit” 3/4” 12 Volt 20 Amps Yes 146.94
FR FR1618 115V Rotary Pump 1” 115 Volt 6.5 Amps No 177.77
FR KITFR1612 Repair Kit for FR1612 & 1614........................ CALL
FR KITFR1618 Repair Kit for FR1618 & 1620........................ CALL
Fuel Pump
Heavy Duty
12 & 24-VOLT #600-105
Bushing
2" Bung
These fuel pumps are ideal D 2" MPT x
2" MPT Adapter Bushing
for use with gas, diesel and 1-1/4" FPT
petroleum based products.
2 Year Warranty Model FR4210 600-105 Cast Iron Threaded Bung Adapter
1-1/4”x6”
Nipple or Bushing: 2” MPT x 2” MPT x 1-1/4” FPT for
• Automatic ByPass Valve, 1-1/4”
use with standard lever couplings, as shown.
Check Valve & Strainer FILL-RITE Suction
Pipe
• 2" Bung Adapter, 1" Allows quick transfer of pump from barrel to
Telescoping Suction Pipe barrel without removing threaded fittings. 151-
• 18’ Power Cord 1-1/4”x1” 98 Suction Pipe is adjustable from 23" to 40".
Bell Reducer
• Carbon Vanes & Seals (If 1” Suction
Pipe is Used)
• Explosion-Proof 1/4 HP UL
Listed Motor
• 30 Minute Duty Cycle
D Part No. Net Ea.
FR 600-105 Adapter Only..................................... $ 17.23
• No Bearing Lubrication
DU 1-1/4X48 1-1/4” Suction Pipe (48”).................. 20.75
Required
FR 151-98 1” Suction Pipe ................................ 23.52
• Can Be Used with an US 678-1-1/4X1 1-1/4” x 1” Bell Reducer................... 2.41
Automatic Nozzle
Model FR4410
1" x 15 ft. hose and nozzle on 12-volt and 24 volt. 20 GPM maximum flow Suction Pipes for Fuel Pumps
(18 GPM with 1” meter). All pumps can be equipped with a meter kit. — Steel Male Pipe Thread by Beveled Other End —
Part No. Wt. Net Ea.
FR FR4210 12-Volt Pump w/Hose & Nozzle......... 36 lbs. $ 384.70
Part No. Size Net Ea.
FR FR4410 24-Volt Pump w/Hose & Nozzle......... 36 lbs. 434.66
FR BD4210D 12-Volt Pump for B21-B100 Biodiesel 36 lbs. 450.05
DU 1X48 Beveled Pipe 1" x 48" $ 18.75
FR 807CMK 3/4" Meter Kit for FR4410.................. 7 lbs. 159.87 DU 1X63 Beveled Pipe 1" x 63" 20.75
FR 901MK4200 1" Meter Kit for 4200/4400................. 7 lbs. 227.82 DU 1-1/4X48 Beveled Pipe 1-1/4" x 48" 20.75
FR F8739 Repair Kit for FR4210 & FR4410....... - 87.44 DU 1-1/4X63 Beveled Pipe 1-1/4" x 63" 23.50
Viton® is a registered trademark of DuPont Performance Elastomers
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0277
450 Repair Kits • Oil Change System • Meters
12 Volt Oil Change System FILL RITE REPAIR KITS
Contain Most Frequently Required Fill Rite Repair Parts
FEATURES: For: FR600C, FR1200C, FR2400C, FR4200, FR4400, SD602, SD1202 Pumps
Part No. Qty. Description Part No. Qty. Description
• Complete with necessary tubing
For 1200C,
1200F6505 1 Rotor Gasket 1200F2770 1 Bypass Spring
and oil storage container.
4200 Series Pumps 1200G9485 5 Vane, Bronze 1200F2756 1 Bypass Valve
& Kits 1200G8881 1 Rotor 100F0790 1 Inlet Gasket
• Eight foot cable with battery clips 1200F6440 1 Rotor Key 100F0760 1 Screen
Repair Kit
• Thermal overload protection #F8739 1200KTF6446 1 Seal Assembly 1200F6721 4 Screw
1200F6455 1 Bypass Gasket 1200F6435 1 Rotor Cover
• BUNA-N impeller
D Part No. Qty. Description Part No. Qty. Description
• 3/8” FPT For 1200A & B 100-11 1 Screen 1200-9 1 Rotor Key
Pumps Only 100-13 1 Gasket 1200-10V 1 Seal Assembly
• 1.4 GPM Open Flow 700-10 1 Poppet 1200-12 1 O-Ring Gasket
Repair Kit
1200-6 1 Rotor 1200-22 1 O-Ring Gasket
#1200-70
Makes a messy job clean and easy. 1200-7 5 Vane
Simply install the oil probe in the engine oil dipstick tube, attach the battery * For NP700 Part No. Qty. Description Part No. Qty. Description
(old style thru 1990) 600-27 1 Gasket 700-10 1 Poppet
clips and flip the switch. Series Pumps - 700A 600-77 1 Viton® O-Ring 700-15 1 O-Ring Gasket
Oil is safely removed and stored in the easy-to-carry container. Oil should
Repair Kit
700-6 1 O-Ring Gasket 700-40K 1 Seal Assembly
700-8 5 Vane 700-33 1 Gasket
be heated to 140˚ F. for maximum pump efficiency. #700-60 700-9 1 Rotor 700-53 1 Rotor Key
Part No. Net Ea. * For FR700 Part No. Qty. Description Part No. Qty. Description
SU 8050-305-426 12 Volt Oil Change System $ 125.00 Series Pumps - 700B F2654 1 Rotor 700-53 1 Rotor Key
(New Style 1990 & F2655 8 Vane 800-115 1 Cover Gasket
SU 8000-643-236 12 Volt Replacement Pump 88.00 Later) 700-40K 1 Seal Kit 1200-12 2 Bypass Gasket
SU 8000-633-236 115 Volt Replacement Pump 101.00 F2756 1 Poppet 300-27 1 Cover Gasket
Repair Kit # F2659 700-15 1 O-Ring Gasket 300-28 1 Buna Gasket
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0681
Bulk Oil Pumps and Meters 451
dultmeier.com
GI L5016 12 Volt Lube Oil Pump, 1/2 HP 4 GPM 40 Amps 34 $ 535.00
GI L5116 115/230 Volt Lube Oil Pump, 1 HP 4 GPM 7.5 Amps 25 326.00
GI L5132 115/230 Volt Lube Oil Pump, 1 HP 8 GPM 13 Amps 35 377.00
GI 142102-01 Portable Cart............................................................................................ 275.00
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0604
452 GPI Fuel Pumps & Meters
Fuel Transfer Pumps 12 & 115-Volt 115-Volt & 230-Volt
12, 15, 18 & 25 GPM GPI ® Combination
2 Year Warranty Fuel Pumps & Meters
These gear pumps are designed for use
with gasoline, diesel fuel or kerosene. • Pre-Assembled Pump & Meter Combo: Convenient & Saves Time
They have a lightweight, corrosion • Each Model Includes 20 or 30 GPM Pump, FM-530 Mechanical Meter, 12’ UL
resistant cast aluminum body. Motors Listed Hose, Automatic or Manual Nozzle & Tank Adapter (not shown)
have a 30-minute “Duty Cycle” under normal
operation. 2" tank bung adapter. U.L. listed. • Designed for Use with Gasoline, Diesel, E15 & B20 Fuels
• 30 Minute Duty Cycle
GPI ® D
Designed for Use with • External Switch Coverplate for Easy Access
Gasoline, Diesel Fuel &
M150S • 2-Year Warranty
shown Kerosene. Also for E-15 Designed for Use with Gasoline,
• U.L. & Canadian Listed
Ethanol & B-20 Biodiesel. Diesel, E-15 & B-20
Model M150S & M180S Features: 12-Volt DC with 15 ft. power cord with 20
amp fuse and ring terminals • 3/4" x 12' Buna-N hose (1” x 12’ on M180S),
manual shut-off nozzle and a 22" to 40" adjustable suction pipe • 15 GPM
(18GPM on M180S) • Maximum PSI is 10 • 20 Amp draw at 30-minute duty
cycle • Use with 3/4” Meter.
Model M1115S Features: 115-Volt AC power • 3/4” x 12' Buna-N hose,
manual shut-off nozzle • 12 GPM output • Maximum PSI is 10 • 1.5 Amp
drain at a 30-minute duty cycle. Includes adjustable suction pipe. (See below D
for automatic nozzles) • Use with 3/4” meter.
Model M3025ML Features: 25 GPM • 1” x 12' hose and manual leaded
nozzle • 15 ft. Power cord • Manual Nozzle. (1” suction pipe sold separately).
Model M3025AL is the same as M3025ML with automatic diesel nozzle
(1” suction pipe sold separately).
Model M3120ML Features: 115-Volt • 20 GPM • 3/4” x 12’ hose & manual Optional
nozzle • Easy access switch • Easy access strainer & check valve. Pedestal
Assembly
Model M3130ML Features: 115/230 Volt • 30 GPM • 1” x 12’ hose & manual
nozzle • Easy access switch • Easy access strainer & check valve.
Wt.
Part No. GPM Wt. Net Ea. Part No. GPM Voltage Lbs. Net Ea.
GI M150S 12-Volt Transfer Pump.......... 15 23 lbs. $ 313.00 GI M3120M Fuel Pump/Meter “Combo”
GI M1115S 115-Volt Transfer Pump........ 12 23 lbs. 337.00 with Manual Nozzle............. 20 115V 60 $ 667.00
GI M180S 12-Volt Transfer Pump.......... 18 23 lbs. 345.00 GI M3120A Fuel Pump/Meter “Combo”
GI M3025ML 12-Volt Transfer Pump.......... 27 57 lbs. 509.00 with Automatic Nozzle........ 20 115V 60 708.00
GI M3025AL 12-Volt Transfer Pump.......... 25 59 lbs. 599.00 GI M3130M Fuel Pump/Meter “Combo”
GI M3120ML 115 Volt Transfer Pump......... 20 51 lbs. 490.00 with Manual Nozzle............. 30 115/230V 85 1133.00
GI M3130ML 115/230 Volt Transfer Pump.. 30 77 lbs. 942.00 GI M3130A Fuel Pump/Meter “Combo”
GI FM530 1” FM530 Mechanical Fuel Meter............... 158.00 with Automatic Nozzle........ 30 115/230V 87 1240.00
GI FM530G 3/4” FM530 Mechanical Fuel Meter............ 151.00 FR 151-98 1” Adjustable Steel Suction Pipe, 22”-40”.......... 23.52
FR 151-98 1” Adjustable Steel Suction Pipe, 22”-40”... 23.52 DU 1X48 1” x 48” Non-Adjustable Steel Suction Pipe....... 18.75
DU 1X48 1” x 48” Non-Adjustable Steel Suction Pipe........ 18.75 GI 133170-01 Optional Pedestal Assembly with Base Foot..... 162.50
HK 45CU Automatic 1” Unleaded Nozzle.................... 64.10
HK 45CHF Automatic 1” Diesel Nozzle, High Flow....... 60.45
GPI ®
12 Volt Fuel Pumps
with Easy Access Strainer &
12 Volt Fuel Transfer Pumps Weight Centering Inlet Base
8 GPM • 12 Volt
25 GPM • 12 Volt
Suitable for Gasoline, Diesel Fuel , Kerosene
These 25 GPM High Capacity 12 Volt Fuel Pumps offer
& E15 & B20 an inlet base located below the center of the pump for
GPI ®
better weight distribution. This also provides quick
and easy access to the strainer without
The EZ-8 Fuel Transfer Pump is removing the pump from the tank
designed for economy and light port. Constructed of lightweight,
duty use. It has a 15 minute on, corrosion-resistant aluminum
30 minute off duty cycle rating bodies. Motors have 30 minute
duty cycle. Includes 1” x 18’ D
(designed for tanks up to 120
gallons maximum). 10’ x 5/8” hose discharge hose, manual or
D
with manual nozzle & 3 piece “trim to fit” auto diesel nozzle, 18’ power
suction tube. Fits 2” tank openings. 15’ power cord, 40 amp circuit breaker,
cord, 14 gauge, 12 Volt, UL listed. inlet check valve, easy
For methanol use, add “M” suffix to the part access strainer and 2”
number. bung adapter (1” suction
pipes extra).
Part No. 12VDC Voltage Pumps GPM Wt. Net Ea.
Part No. GPM Wt. Net Ea. GI M3025CB 12-Volt Pump, Manual Nozzle.... 25 67 lbs. $ 553.00
GI M3025CB-AD 12-Volt Pump, Auto Diesel Nozzle 25 69 lbs. 620.00
GI EZ8 12 Volt Fuel Pump 8 18 lbs. $ 221.00
GI M3025CS-PO 12-Volt Pump ONLY.................. 25 54 lbs. 502.00
EZ8-M is pump only fitted for methanol plus other fuels noted above.
DU 1X48 1” x 48” Non-Adjustable Steel Suction Pipe 18.75
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0278
MP Petroleum Transfer Pumps 453
Fuels Include:
• Gasoline • Fuel Oil
• Diesel • Kerosene
• Bio-Diesel • Aviation Gasoline
• Ethanol • Jet A / JP-8
• E-85 Ethanol
Model PG Pumps
The PG Model is available in Pedestal
mount or Close Coupled mount to
Compatible for Gasoline, Kerosene, Avgas & Jet Fuel
C Face Class I Group D Explosion
Proof electric motors. Ductile Iron
volute and adapter. The open impeller Model PG Pumps for Gasoline, Kerosene, Avgas & Jet Fuel
is cast iron. Aluminum wear plate. Type PetrolMaxx Max. GPM @ Max. Spec. Close or Wt.
2 mechanical seal is carbon, Viton® Part No. Series GPM 20 PSI Gravity Ports HP Voltage Phase Long Cpld. Lbs. Net Ea.
and silicon carbide. MX 35639 8 150 100 1.20 2” 3 230/460V 3 Close 90 $ 1728.24
MX 36048 15 320 275 0.95 3” 5 230/460V 3 Close 180 3181.21
MX 36876 8 150 100 1.00 2” 2 115/230V 1 Close 80 2047.88
MX 37957 15 320 275 0.80 3” 5 115/230V 1 Close 180 3971.60
MX 35728 8 150 100 - 2” - - ** Pedestal Pump ONLY 50 923.23
MX 35734 15 320 275 - 3” - - ** Pedestal Pump ONLY 90 1446.38
MX PG30 30 480 480 - 3” x 2.5” - - * Pedestal Pump ONLY 115 2273.15
* Use PG30 with 20 HP, 3450 RPM, Explosion-Proof Motor. ** Use Pedestal Pumps with Explosion-Proof Motors.
Model PO Pumps
Compatible for Diesel, BioDiesel & Fuel Oil
Model PE Pumps
Compatible for E-10/E-15 Ethanol & E-85 Ethanol
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0963
Diesel Pump Units 455
Shown with
Nozzle
Sold Separately.
Remote Dispenser Pumps
Part No. Voltage GPM Ports Net Ea.
D GI 133200-10 115 Volt 20 1” x 3/4” $ 458.00
GI 133220-05 115/230 Volts 30 1-1/4” x 1” 518.00
DU 1X48 1” x 48” Siphon Tube, Steel............... 18.75
DU 1X63 1” x 63” Siphon Tube, Steel............... 20.75
Part No. Description Net Ea. DU 1-1/4X48 1-1/4” x 48” Siphon Tube, Steel......... 20.75
GI 13330005 FM-530 Meter in a Remote Dispenser. Remote Dispenser DU 1-1/4X63 1-1/4” x 63” Siphon Tube, Steel......... 23.50
Unit ONLY without hose or nozzle........................... CALL
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0943
Products for Diesel Exhaust Fluid (DEF) 457
D Sold
• Up to 6.5 GPM Flow Rate, Up to 100 PSI Air
Separately
Pressure
• Bung Adapter Included - Securely Fastens
Pump to Drum
Part No. Description Net Ea.
• Polypropylene Construction, Fluorocarbon FR SA1208KP 3/4” SS Vane Pump (1/2 HP), 12’ DEF
Seals Hose Assembly, SS Automatic Nozzle,
D
• Telescoping Suction Pipe Included 825 Meter & Universal Mount Plate, Less
Suction Hose - See below . ..................... $ 1673.61
FR FRHA6 3/4” x 6” Suction Hose............................ 145.38
FR KIT55DU 55 Gallon Drum Cart................................ 630.75
Part No. Description Net Ea.
FR FRHP32V DEF Hand Lever Pump .......................... $ 67.44
FR KITA32V
DEF Hose (3/4” x 8’) with Ball Tap Valve
(for above pump)................................... 27.15
DEF Poly Transfer
FR FRAP32V DEF Air Operated Pump.......................... 243.80 Pumps
FR KITA32VMN DEF Hose (3/4” x 8’) with Manual Nozzle
(for Air-Operated Pump)........................ 159.87 • 115 Volt or 12 Volt DC Gear Pumps
• Delivers up to 12 GPM
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0898
Lubrication Equipment 463
3/16" I.D., working pressure 3,000 lbs. min. Grease Gun Part No. Net Ea.
NS 333 Bearing Packer $ 50.30
burst 12,000 lbs., 1/8" NPT male both ends. Whip Hose
D Portable Pumps
MODEL 321: Fits open head pails through 5
gallons.
MODEL 336: Fits 120 lb. drums. Both include
D pump, pail cover, and 4' of clear vinyl hose with
D
D curved discharge.
No. 28 No. 55 No. 80 Part No. Net Ea.
Hydraulic Coupler Adapter Tube Loader Nipple NS 321 5-Gallon Pump $ 27.55
Snap-on Coupler w/ball check 1/8" NPT - 5-1/2" long 1/8" Threads NS 336 120 lb. Pump 40.40
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0470
464 Lubrication Equipment
BUCKET PUMP Metering Control Valves
High Pressure for Grease or Heavy Oil Meter and control valve for oils,
GREASE PUMP ATF and antifreeze. Easy to read
3-1/2" dial totals 16 quarts in 1/4 quart
2500 PSI
D
graduations. Includes 10" flex hose and D
Hand operated grease pump for full open headed nozzle. Ports are 1/2" NPT.
pails up to 6-1/2 gallons in size (25 to 50 lb.).
Includes pump, pail cover, carrying handle, Designed specifically to dispense
follower plate, 6 ft. of high pressure hose and motor oils (S.A.E. 80-240), automatic
No. 28 coupler. Can develop over 3,500 PSI. transmission fluid and antifreeze
D
Delivers approximately 1-1/2 lbs. of grease per Model 550 (Ethylene Glycol). Perfect balance,
100 strokes for #1 or #2 grease. lightweight, ruggedness, & comfortable
Part No. Wt. Net Ea. grip make it the best choice for overhead
NS 550 Bucket Grease Pump, 2500 PSI ..... 11 lbs. $ 74.35 1515 Meter reel systems.LCD display. Programmable
Control Valve
to dispense in pints, quarts, liters, or
gallons. Ports are 1/2" NPT. 1509 Electronic
19-Volt Features: Lube Meter
• 8000 PSI Rated
Cordless • (2) NICAD Batteries
Part No. Description Wt. Net Ea.
NS 1515 Metering Control Valves . .............. 5 lbs. $ 280.00
Grease • 30” Whip Hose with Spring
Guard NS 1509 Electronic Lube Meter, Pistol Style. 3 lbs. 294.00
Gun • Holds 14-1/2 Oz. Cartridge
• 1/8” NPT Threads
• Battery Charger (1 hour
Suction Gun
charging cycle) A professional model for fast,
• Multiple Loading Options clean removal of oil from filters,
(cartridge, suction or bulk) D
gear cases, transmissions
D • Air Bleeder Valve
or differentials. For sampling
• Hard Plastic Case
D engine oil or to quickly transfer
• Recommended Grease up to Model 101
NLGI #2 at minimum of 50° F. any fluid lubricant.
Part No. Description Net Ea. • Large capacity — will hold up to 17 ounces of fluid lubricant.
NS 912-18 Battery Operated Grease Gun....................... $ 133.50 • Flexible nozzle — for transmission, differential or oil filter service.
NS 91201-18 19 Volt Replacement Battery for 912-18 Gun 42.30 • 12" Clear Vinyl Hose
Part No. Wt. Net Ea.
• Full automatic Automatic Air Operated NS 101 Suction Gun ........... 2 lbs. $ 9.01
operation—cycles
continuously when trigger Grease Gun
is pulled, self-priming.
• Flexible 18" high
Pump Oilers
pressure hose.
• 6000 PSI Capability. D
Rechargeable Grease Gun Golden Rod Pump Oilers are built of heavy gauge steel
and will stand up to rough service. Designed to deliver a
POWER-LUBER 12 Volt drop or a stream of oil. Easy to refill. The highest quality
D materials are used throughout with wrought iron spouts.
Economy-Packed in Copper bronze finish. No. 624 has adjustable spray tip
a Rugged Corrugated which delivers a fine mist or a long stream when handling
Storage Box cleaners, kerosene, light lubricants, solvents, insecticides
and penetrating oils.
Model 120B3
1244 Filler Nipple
Spout
D Part No. Spout Type Length Capacity Net Ea.
DN 624 Spray Tip, Rigid 5" 10 oz. $ 10.30
Model 91108: Enables DN 707 Flexible 8" 12 oz. 9.20
hand guns to be loaded DN 720 Angle, Rigid 8" 12 oz. 9.19
using filler pump method. DN 120B2 Angle, Rigid 10" 24 oz. 20.45
D Includes ball check; 1/8" DN 120B3 Flexible 12" 24 oz. 20.45
NPT Male.
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0472
Lubrication Pumps & Accessories 465
Model 1584 Control Handle for ATF, gear oil and motor oil. Low pressure control handle
with 15" rigid (not flexible) spout and no. 26 non-drip nozzle. Inlet is 1/2" FPT.
Gasoila® Leak-Tech
Model 1587 Control Handle is the same as #1584, except it has a 18" flexible spout. Model LS16
Model 1520
Detects leaks on any system carrying natural
Preset Meter for Motor Oil D or LP gas. Also use on refrigeration and air
Preset 1 to 60 U.S. quarts, totalizes in U.S. gallons. conditioning units, air lines and pumps, etc. Quick
Automatically shuts off at preselected quantity. and positive leak detection on all types of piping D
Includes 1/2" FPT swivel inlet and non-drip rigid
nozzle. Good to 240 wt. gear lube oils. materials. Comes in a 1 pint spray bottle.
Model 1534
Booster Control Valve
NO. 4HC-250B Part No. Accessories Net Ea.
Booster Control Valve. Can be used Pressure Regulator NS 1534 Booster Control Valve $ 40.90
D as a regular control valve Air Regulator. Forged brass NS 1545 Swivel..................... 26.05
by squeezing handle body with 4 ports, 1/4" NPT KI L72C Oil-Fog Lubricator... 34.00
once. If additional D (F) for a pressure range of NS 1558 Air Line Filter.......... 61.10
pressure is required, 10-200 P.S.I. GE 4HC-250B Air Regulator........... 49.90
squeeze handle again. Will develop
pressure up to 12,000 P.S.I. Has
1/8" NPT (F) inlet.
DULTMEIER SALES • OMAHA, NE (800) 228-9666 • www.dultmeier.com • DAVENPORT, IA (800) 553-6975 E0473
Pump Index JOHN BEAN ....................................................................... 131
JOHN BLUE............................................. 101,131,133,144-146
12-Volt . .................................125,133-135,151,448,449,451,452 JUROP................................................................................. 169
ACE ...................................................................... 118-120,123 Liquid Feed ................................................................. 139-142
Acid............................................................................... 164,306 LITTLE GIANT................................................ 125,149-151,199
Air-Operated, Chemical .............................................. 136-138 Magnetic Drive.............................................................. 120,149
Air-Operated, Petroleum ............................... 157,457,463,465 Motor Driven Drum............................................................... 166
Alkali.................................................................................... 164 MP-FLOMAX ....................................... 96-99,102,123,125,453
AQUATEC ........................................................................... 133 Multi-Stage........................................................................... 113
AR ....................................................................................... 180 OBERDORFER .................................................................. 139
BANJO ............................................................ 96,103,105,106 Oil ......................................................................... 163-166,169
Barrel ............................................................. 163-166,449,464 PACER .................................................................. 103,104,165
BLUE WHITE ............................................................... 154,156 Parts Washer ...................................................................... 149
Booster.......................................................................... 167,168 Peristaltic Injector . .............................................................. 156
Bus ..................................................................................... 123 Pesticide........................................................................ 131,147
Carpet Cleaning . .................................................. 134,135,147 Petroleum . ....................................... 163,166,449,451,453,457
CAT PUMPS .......................................... 174-176,185,193,391 PETROLMAXX.................................................................... 453
Centrifugal ..................................................96-99,101-124,453 Piston & Plunger.......... 140,145,147,157,163,165,174-184,194
Chemical........................96-99,101-114,116-126,128-131,133-142, Polypropylene .................................................................... 166
............................................144-146,148,149,154-159,164-166,409,453 Pond..................................................................................... 199
Chlorine................................................................................ 164 PROCON ........................................................................... 148
Circulator ............................................................................ 186 PUMPTEC........................................................................... 147
COMET Plunger ................................................................. 183 Reclaim ....................................................................... 155,156
CONDE Vacuum.................................................................. 170 Remote Dispenser............................................................... 455
CORKEN ............................................................................ 409 Roller ........................................................................... 128,140
CRANE DEMING ................................................................ 110 ROPER ........................................................................ 141,142
Dairy.................................................................................... 164 Rotary Hand.................................................................. 163,166
DELAVAN ............................................................. 124,128,133 Rotary Vane .......................................................... 148,449,457
Diaphragm .......................................117,129-131,133-138,154,155,157-159 Rotoprime ........................................................................... 115
Diesel................................................................................... 455 SANDPIPER ....................................................................... 137
Diesel Exhaust Fluid (DEF).................................................. 457 SCIENCO .................................................................... 157,158
Drum ....................................................... 163,165,166,463,464 SCOT ...................................................... 102,103,108,109,453
EBARA . ................................................................ 102,112,152 Sewage.................................................................. 116,149-153
Electric Fuel ................................................................. 447-449 Sewer Cleaning . ................................................................. 185
EZI-ACTION . ...................................................................... 165 Shallow Well Jet .................................................................. 167
FATBOY................................................................................ 133 SHERTECH ................................................................. 126,140
Feed Supplement . ....................................................... 139-142 SHURFLO.............................................................. 134,138,159
FILL-RITE .............................. 159,163,165,447-449,451,455,457 Sludge . ............................................................................... 117
Flammable Liquid . .............................................................. 115 SOTERA ................................................. 159,447-449,451,457
FLINT & WALLING . ..................................................... 167,200 Sprayer ................................................... 118-124,128,134,147
FLOJET ....................................................................... 135,138 Sprinkler ............................................................................. 123
FLOMAX ............................................................ 96-99,102,123 Squeeze . ..................................................................... 146,211
Flow Serve ................................................................... 157,158 STA-RITE........................................................ 123,156,167,168
Fountain ............................................................................. 200 Stainless .......................................... 111-113,152,153,166-168
Fuel ......................................... 115,163,165,166,394, 447-449, STENNER . ......................................................................... 156
........................................................................ 451,452,455,457 Submersible ................................................... 149-153,167,199
Gear ............................................................................ 139-142 Sump .................................................................... 149-153,386
GENERAL ............................................................ 177-179,185 SUNTEC ............................................................................ 394
GIANT........................................................................... 184,185 TACO................................................................................... 186
GORMAN RUPP............................................. 102,114-117,166 Thermoplastic...................................................................... 104
GOULDS . ........................................ 110-113,123,152,153,168 Trash............................................................................. 116,117
GPI ................................................................ 157,163,451,452 Turbine ................................................................................ 124
GRACO ............................................................................... 136 TURBO 90........................................................................... 124
GRUNDFOS ................................................................ 113,186 UDOR .......................................................................... 130,194
GUSHER.............................................................................. 103 Utility ............................................................................ 125,157
Hand.................................................................................... 163 Vac-U Seal........................................................................... 101
Hand .............................................................. 163-166,456,457 Vacuum ........................................................................ 169-171
High Pressure ........................................ 117,174-181,183,184 VERSAMATIC ..................................................................... 137
Hydra-Cell............................................................................ 155 WANNER ..................................................................... 155,193
Hydraulic Driven................................................................... 194 WARREN RUPP .................................................. 117,137,151
HYPRO ....................... 107,113,120-125,128,129,139,181,182 Water Garden & Sprinkler .......................................... 123, 199
Impeller ............................................................................... 126 Well ..................................................................................... 167
Injection ....................................................................... 144,154 YAMADA ............................................................................ 136
Jet ...................................................................................... 167 ZOELLER ........................................................................... 151
Jetting ................................................................................. 185