Professional Documents
Culture Documents
TDS - Alkyd Topcoat
TDS - Alkyd Topcoat
TDS - Alkyd Topcoat
Alkyd Topcoat
Product description
Alkyd Topcoat is an alkyd based topcoat for both exterior and interior use. This product is part of a complete system
which has a low flame spread certificate.
Recommended use
Alkyd topcoat in a traditional alkyd system is suitable for steel and woodwork. The product has good weather stability
and colour stability.
Physical properties
Colour White, Std 38, Std 49, Std 137 and Black
Solids (vol %)* 44 ± 2
Gloss Glossy
Gloss retention Good
Water resistance Limited
Abrasion resistance Fair
Flexibility Good
*Measured according to ISO 3233:1998 (E)
Coated surfaces
Clean, dry and undamaged compatible primer. Please contact your local Jotun office for more information.
Other surfaces
The coating may be used on other substrates. Please contact your local Jotun office for more information.
Application methods
Spray Use airless spray or conventional spray
Brush Recommended for stripe coating and small areas, care must be taken to achieve the specified dry
film thickness.
Roller May be used. However when using roller application care must be taken to apply sufficient material in
order to achieve the specified dry film thickness.
Application data
Mixing ratio (volume) Single pack.
Drying time
Drying times are generally related to air circulation, temperature, film thickness and number of coats, and will be
affected correspondingly. The figures given in the table are typical with:
* Good ventilation (Outdoor exposure or free circulation of air)
* Typical film thickness
* One coat on top of inert substrate
The given data must be considered as guidelines only. The actual drying time/times before recoating may be shorter or
longer, depending on film thickness, ventilation, humidity, underlying paint system, requirement for early handling and
mechanical strength etc. A complete system can be described on a system sheet, where all parameters and special
conditions could be included.
Storage
The product must be stored in accordance with national regulations. Storage conditions are to keep the containers in a
dry, cool, well ventilated space and away from source of heat and ignition. Containers must be kept tightly closed.
Handling
Handle with care. Stir well before use.
Packing size
20 litre container
For detailed information on the health and safety hazards and precautions for use of this product, we refer to
the Material Safety Data Sheet.
DISCLAIMER
The information in this data sheet is given to the best of our knowledge based on laboratory testing and practical
experience. However, as the product can be used under conditions beyond our control, we can only guarantee the
quality of the product itself. We also reserve the right to change the given data without notice. Minor product variations
may be implemented in order to comply with local requirements.
If there is any inconsistency in the text the English (UK) version will prevail.
Jotun is a World Wide company with factories, sales offices and stocks in more than 50 countries. For your nearest local Jotun address
please contact the nearest regional office or visit our website at www.jotun.com
Alkyd Topcoat
SECTION 1: Identification of the substance/mixture and of the
company/undertaking
1.1 Product identifier
Product name : Alkyd Topcoat
Product code : 12300
Product description : Coatings: Solvent-borne.
Product type : Liquid.
Other means of : Not available.
identification
1.2 Relevant identified uses of the substance or mixture and uses advised against
Identified uses
Uses in Coatings - Industrial use
Uses in Coatings - Professional use
Tel: +44 17 24 40 00 00
Fax: +44 17 24 40 01 00
SDSJotun@jotun.com
Environmental hazards : Toxic to aquatic organisms, may cause long-term adverse effects in the aquatic
environment.
See Section 16 for the full text of the R phrases or H statements declared above.
See Section 11 for more detailed information on health effects and symptoms.
There are no additional ingredients present which, within the current knowledge of the supplier and in the concentrations
applicable, are classified as hazardous to health or the environment, are PBTs or vPvBs or have been assigned a
workplace exposure limit and hence require reporting in this section.
Type
[1] Substance classified with a health or environmental hazard
[2] Substance with a workplace exposure limit
[3] Substance meets the criteria for PBT according to Regulation (EC) No. 1907/2006, Annex XIII
[4] Substance meets the criteria for vPvB according to Regulation (EC) No. 1907/2006, Annex XIII
Occupational exposure limits, if available, are listed in Section 8.
4.2 Most important symptoms and effects, both acute and delayed
Potential acute health effects
Eye contact : May cause eye irritation.
Inhalation : Vapours may cause drowsiness and dizziness.
Skin contact : May cause skin irritation.
Ingestion : No known significant effects or critical hazards.
Over-exposure signs/symptoms
Eye contact : No specific data.
Inhalation : Adverse symptoms may include the following:
nausea or vomiting
headache
drowsiness/fatigue
dizziness/vertigo
Skin contact : No specific data.
Ingestion : No specific data.
4.3 Indication of any immediate medical attention and special treatment needed
Notes to physician : Treat symptomatically. Contact poison treatment specialist immediately if large
quantities have been ingested or inhaled.
Specific treatments : No specific treatment.
Special protective : Fire-fighters should wear appropriate protective equipment and self-contained
equipment for fire-fighters breathing apparatus (SCBA) with a full face-piece operated in positive pressure
mode. Clothing for fire-fighters (including helmets, protective boots and gloves)
conforming to European standard EN 469 will provide a basic level of protection for
chemical incidents.
6.2 Environmental : Avoid dispersal of spilt material and runoff and contact with soil, waterways, drains
precautions and sewers. Inform the relevant authorities if the product has caused environmental
pollution (sewers, waterways, soil or air). Water polluting material. May be harmful to
the environment if released in large quantities.
When operators, whether spraying or not, have to work inside the spray booth, ventilation is unlikely to be sufficient to
control particulates and solvent vapour in all cases. In such circumstances they should wear a compressed air-fed
respirator during the spraying process and until such time as the particulates and solvent vapour concentration has fallen
below the exposure limits.
Barrier creams may help to protect the exposed areas of the skin but should not be
applied once exposure has occurred.
For right choice of glove materials, with focus on chemical resistance and time of
penetration, seek advice by the supplier of chemical resistant gloves.
The user must check that the final choice of type of glove selected for handling this
product is the most appropriate and takes into account the particular conditions of
use, as included in the user's risk assessment.
Body protection : Personal protective equipment for the body should be selected based on the task
being performed and the risks involved and should be approved by a specialist
before handling this product.
Other skin protection : Appropriate footwear and any additional skin protection measures should be selected
based on the task being performed and the risks involved and should be approved by
a specialist before handling this product.
Respiratory protection : If workers are exposed to concentrations above the exposure limit, they must use
appropriate, certified respirators. Use respiratory mask with charcoal and dust filter
when spraying this product.(as filter combination A2-P2). In confined spaces, use
compressed-air or fresh-air respiratory equipment. When use of roller or brush,
consider use of charcoalfilter.
Environmental exposure : Emissions from ventilation or work process equipment should be checked to ensure
controls they comply with the requirements of environmental protection legislation. In some
cases, fume scrubbers, filters or engineering modifications to the process equipment
will be necessary to reduce emissions to acceptable levels.
Exposure to component solvent vapour concentrations in excess of the stated occupational exposure limit may result in
adverse health effects such as mucous membrane and respiratory system irritation and adverse effects on the kidneys,
liver and central nervous system. Solvents may cause some of the above effects by absorption through the skin.
Symptoms and signs include headache, dizziness, fatigue, muscular weakness, drowsiness and, in extreme cases, loss
of consciousness. Repeated or prolonged contact with the preparation may cause removal of natural fat from the skin,
resulting in non-allergic contact dermatitis and absorption through the skin. If splashed in the eyes, the liquid may cause
irritation and reversible damage. Swallowing may cause nausea, diarrhoea, vomiting, gastro-intestinal irritation and
chemical pneumonia.
Contains 2-butanone oxime, 2-ethylhexanoic acid, cobalt salt. May produce an allergic reaction.
Marking : The environmental hazardous / marine pollutant mark is only applicable for packages
containing more than 5 litres for liquids and 5 kg for solids.
14.4 Packing group : III
14.5 Environmental hazards : Yes.
14.6 Special precautions : Not available.
for user
Additional information
ADR / RID : Tunnel restriction code: (D/E)
Hazard identification number: 30
IMDG : Emergency schedules (EmS)
F-E, S-E
14.7 Transport in bulk : Not available.
according to Annex II of
MARPOL 73/78 and the IBC
Code
15.2 Chemical Safety : This product contains substances for which Chemical Safety Assessments are still
Assessment required.
Full text of classifications : Acute Tox. 4, H312 ACUTE TOXICITY: SKIN - Category 4
[CLP/GHS] Acute Tox. 4, H332 ACUTE TOXICITY: INHALATION - Category 4
Aquatic Acute 1, H400 AQUATIC TOXICITY (ACUTE) - Category 1
Aquatic Chronic 1, H410 AQUATIC TOXICITY (CHRONIC) - Category 1
Aquatic Chronic 2, H411 AQUATIC TOXICITY (CHRONIC) - Category 2
Asp. Tox. 1, H304 ASPIRATION HAZARD - Category 1
Carc. 2, H351 CARCINOGENICITY - Category 2
Eye Dam. 1, H318 SERIOUS EYE DAMAGE/ EYE IRRITATION - Category 1
Flam. Liq. 3, H226 FLAMMABLE LIQUIDS - Category 3
Preparation of material for application : Provide a good standard of general ventilation (not less than 3 to 5 air changes
per hour).
Roller, spreader, flow application : Provide a good standard of general ventilation (not less than 3 to 5 air changes
per hour).
Spraying - Manual : Provide enhanced general ventilation by mechanical means. Wear a respirator
conforming to EN140 with Type A/P2 filter or better.