Professional Documents
Culture Documents
HPM PDF
HPM PDF
NTWKNUM range = 1 to 20
NIM's UCN That This Point Is In |__.__| default = Not applicable
NODENUM range = 1 to 64
HPMM's Address On The UCN |__.__| default = Not applicable
SLOTNUM
Slot Number l__.__.__| 1-999 (but<= the value in NDCSLOT)
l__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__l D1
1
l__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__l D2
2
ST2_OP3 Off 3 3
State 2 - Output 3 On
1 l__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__. 1
__.__.__l
2 l__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__. 2
__.__.__l
3 l__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__. 3
__.__.__l
Maintenance Statistics
Maximum Hours Maximum Number of
Allowed in Each State Transistions into State
N/A if FBTIME = 0.
OFFNRMPR NoAction Alarm not reported to the system and not annunciated
Offnormal Alarm Priority (R670 and
later) Alarm is historized, not reported to US, not annunciated
Journal Alarm is historized, reported to US, and annunciated
Low Alarm is historized, reported to US, and annunciated
High Alarm is historized, reported to US, and annunciated
Emergency Not historized, reported to the printer, not annunciated
Printer Alarm historized, reported to the printer, not annunciated
JnlPrint
$OFSELCT (R681 and later) Cutout range = Cutout, Allow
Off Normal Selective Cutout Allow default = Cutout
HP88-607
Page 7 of 7
09/08
HPM Digital Composite Point
Unit: Tagname: Engineer: Date:
None No Reporting
EVTOPT Eip Digital PV changes invoke Event-Initiated
Event Reporting Option Processing
l__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__.__l range = Not applicable
EIPPCODE default = Null
Event Init Proc Destination
HP88-602
HPM Analog Input Point Page 1 of 8
09/08
Unit: Tagname: Engineer: Date:
NTWKNUM range = 1 to 20
|__.__|
NIM's UCN That This Point Is In default = Not applicable
NODENUM range = 1 to 64
|__.__|
HPMM's Address On The UCN default = Not applicable
MODNUM range = 1 to 40
|__.__|
I/O Module Number default =Not applicable
SLOTNUM 1-16 (For HLAI or STIM module)
|__.__|
Slot Number 1-8 (For LLAI or PI module)
1-32 (For LLMUX and RHMUX modules)
SLWSRCID range = 1 – 16
Slidwire Voltage Slot ID (number) l__.__l default = 1
STI_EU
Applies if – SENSRTYP = SFM SENSRTYP = STT AND
STI Engineering Units
Applies if SENSRTP=STT
PIUOTDCF Off Thermocouple fault detection
Open TC Detection Enable Option On range = Off or On.
CJTACT On On = Internal cold Jct.compensation active
Int. Cold Jct. Compensation Off Off = External cold Jct.compensation active
C PI Only
C1 range = Real Number t0.0
Scaling Constant 1 l__.__.__.__.__.__.__.__l default = 1.0
C2 range = Real Number t0.0
Scaling Constant 2 l__.__.__.__.__.__.__.__l default = 1.0
TIMEBASE Seconds Minutes Hours PV & Setpoint Eng. Units per
Input Time Base Second, Minute, or Hour
PVALDB
PV Alarm Deadband In % Half One Two Three Four Five EU
$OLDEVDS
Open-Line Detect Event Disable Enable Allows BADPV alarms when open line
detected.
Applies if PNTMODTY = HLAI, STIM, PI, or if SENSRTYP not THERMCPL or if SENSRTYP not RTD
$OLDEVDS
Open-Line Detect Event Disable NOOTDETC Value must be selected. Point operation is
not affected by this function.