Professional Documents
Culture Documents
Elect 2
Elect 2
Base your
decision on reason rather than emotions.
A. Quantitative Thinking.
B. Interpersonal skill.
C. Honesty.
D. Logical thinking.
3. In HDL Based digital systems the arithmetic multiplication function is difficult to synthesize.
Design solution to this challenge do not include:
A. Sequential generation of partial products
B. Hardware intensive simultaneous generation of partial products
C. Implementation of booths algorithm to minimize generation of partial products
D. Sequential right shifts of the arguments
4. The wind load Lsi In newton’s on an overhead line structure is calculated using the following
2
formula. Lsi = 0.613V2 m/s Kz GRF ICf Am
What does the Kz term represent?
A. Force coefficient
B. Guest response Factor
C. Velocity pressure coefficient
D. Wind speed
5. The self-discharge rate of a lead-acid battery is least dependent on which of the following
factors?
6. A digital signal processor (DSP) is designed to perform FFT operations for a digital
oscilloscope that utilizes a 12-bit A/D converter. the most cost effective ALU architecture for
this CPU is a:
A. Fixed-point multiplier with an 8-bit data path
B. Floating-point multiplier with an 8-bit data path
C. Fixed-point multiplier with a 16-bit data path
D. Floating-pointing multiplier with a 16-bit data path
8. An engineer is offered some additional gifts and services in exchange for using superior
materials on a remodelling project. This was not detailed in the contract. He should:
A. Take the offer and use the special materials
B. Reject the offer
C. Ask her boss which of the gifts to accept
D. Accept the gifts but use the materials specified in the contract in order to retain
neutrality.
9. In the receiver of a wireless system, we must amplify the received signal using.
A. Power amplifier
B. Differential amplifier
C. An active filter
D. A low-noise amplifier
12. The interdisciplinary nature of engineering has implications for the appropriateness of
specialization. Which of the fallowing is correct?
A. Since all engineering projects are interdisciplinary, all engineers should be expert in all
fields of engineering.
B. The interdisciplinary nature of engineering means that all engineers should study
‘general engineering’ rather than specialize in a single area.
C. Most engineers will wish to specialize, but all engineers must be able to work effectively
alongside others with complementary skills.
13. This is a type of semiconductor that only allows current to flow in one direction. It is usually
used to rectify AC signals (conversion to DC).
A. Diode
B. Transformer
C. Inductor
14. The noise margins of an inverter with VOH=3 V, VH=2V, VOL=0.5V, VIL=0.8V is
A. NMH=1V, NML=1.5V
B. NMH=0.3V, NML=1V
C. NMH=2.2V, NML=0.3V
D. NMH=1V, NML=0.3V
17. In conducting a power-flow (or load-flow) study using conventional iterative calculations,
which of the fallowing statements is most nearly correct?
A. One bus is designated as a slack bus, and the others are designated as voltage-controlled
buses or load buses.
B. One bus is designated as a voltage-controlled bus, and the others are designated as slack
buses or load buses.
C. One bus is designated as a load bus, and the others are designated as voltage-controlled
buses or slack buses.
D. There may be any number of slack busses, voltage-controlled buses, and load buses
designated, as long as they total the number of buses in the network.
20. The equivalent circuit of induction machine at no load is the same as that of the transformer
but with
A. Open circuited secondary.
B. Short circuited secondary.
C. Open circuited primary.
D. Short circuited primary.
21. Three 30-µF capacitors are connected in star (Y) form between the terminals A, B, C and a
junction point N as shown in the figure, the capacitance (µF) between terminals A and B is
most nearly.
A. 2/30
B. 15
C. 30
D. 60
E.
22. The output D in the circuit is.
A. B(A+C)
B. (A+B) (B+C)
23. Which of the fallowing types of material has high thermal and electrical conductivity?
A. Ceramic
B. Metal
C. …………….( Any other write here)
24. For the diagram shown, what is the approximate required minimum clearance distance, R, if
the phase voltage of the live parts is 13,800 V?
A. 1.8 m
B. 2.5 m
C. 3 m
D. 4 m
25. The accreditation board for engineer and technology (ABET) is an accrediting agency for.
A. Engineering education programs.
B. Engineering fundamentals examinations.
C. Engineering firms.
D. All of the above.
26. In 50Hz induction machine, if the no load speed is 745 r.p.m, the synchronous speed is
A. 700 rpm.
B. 750 rpm.
C. 800 rpm.
D. 850 rpm.