Professional Documents
Culture Documents
Fault Tolerant Ethernet Status Server and Auxiliary Display Users Guide EPDOC-XX38-en-410
Fault Tolerant Ethernet Status Server and Auxiliary Display Users Guide EPDOC-XX38-en-410
Fault Tolerant Ethernet Status Server and Auxiliary Display Users Guide EPDOC-XX38-en-410
EPDOC-XX38-en-410A
March 2012
Release 410
Document Release Issue Date
EPDOC-XX38-en-410A 410 0 March 2012
Disclaimer
This document contains Honeywell proprietary information. Information contained herein is to be used solely
for the purpose submitted, and no part of this document or its contents shall be reproduced, published, or
disclosed to a third party without the express permission of Honeywell International Sàrl.
While this information is presented in good faith and believed to be accurate, Honeywell disclaims the implied
warranties of merchantability and fitness for a purpose and makes no express warranties except as may be stated
in its written agreement with and for its customer.
In no event is Honeywell liable to anyone for any direct, special, or consequential damages. The information
and specifications in this document are subject to change without notice.
Copyright 2012 - Honeywell International Sàrl
2 www.honeywell.com
Contents
1 Introduction ............................................................................................................................................ 5
1.1 Overview of Honeywell Fault Tolerant Ethernet (FTE) ..................................................................................... 6
1.1.1 FTE status component ......................................................................................................................... 6
1.1.2 FTE intermediate driver and Heartbeat provider software .................................................................. 6
1.2 Viewing FTE status ............................................................................................................................................. 7
1.2.1 Access status displays .......................................................................................................................... 7
1.2.2 FTE Status displays ............................................................................................................................. 7
1.2.3 System management display ................................................................................................................ 8
2 Installing FTE Status Display ................................................................................................................ 9
2.1 Introduction ....................................................................................................................................................... 10
2.2 Installing FTE Status Server ............................................................................................................................. 11
2.2.1 Install FTE status components on TPS nodes .................................................................................... 11
2.2.2 Install FTE status components on Experion nodes ............................................................................ 11
3 FTE Status Server ................................................................................................................................ 13
3.1 Introduction ....................................................................................................................................................... 14
3.1.1 About FTE status server .................................................................................................................... 14
3.1.2 FTE status server display ................................................................................................................... 14
3.1.3 FTE status component fields ............................................................................................................. 14
3.1.4 Device status and information details ................................................................................................ 15
3.2 Using the FTE status display ............................................................................................................................ 17
3.2.1 Open the FTE status display .............................................................................................................. 17
3.2.2 Change the view in the FTE Status Server details pane .................................................................... 19
3.2.3 Change FTE Component Status ......................................................................................................... 19
4 FTE Status Auxiliary Display ............................................................................................................... 21
4.1 Overview of FTE Status Auxiliary Display ...................................................................................................... 22
4.1.1 FTE status auxiliary fields ................................................................................................................. 22
4.1.2 FTE Status Auxiliary Display status icon .......................................................................................... 23
4.1.3 Icon color states for Links ................................................................................................................. 23
4.2 Using the FTE Status Auxiliary Display .......................................................................................................... 25
4.3 Monitoring Link Status from the Auxiliary Display ........................................................................................ 26
4.3.1 Link status states ................................................................................................................................ 26
4.3.2 Interface link status details ................................................................................................................ 26
4.3.3 Example of silent port ........................................................................................................................ 27
4.4 Viewing FTE Status Auxiliary Display of remote FTE node ........................................................................... 29
4.4.1 Display remote node status ................................................................................................................ 29
5 Notices .................................................................................................................................................. 31
5.1 Documentation feedback .................................................................................................................................. 32
5.2 Support and other contacts ................................................................................................................................ 33
5.3 Training classes ................................................................................................................................................. 36
3
CONTENTS
4 www.honeywell.com
1 Introduction
Related topics
“Overview of Honeywell Fault Tolerant Ethernet (FTE)” on page 6
“Viewing FTE status” on page 7
5
1 INTRODUCTION
6 www.honeywell.com
1 INTRODUCTION
7
1 INTRODUCTION
• FTE Status Auxiliary displays the individual communication link states for all FTE and Heartbeat nodes
within the "Viewed By" node's multicast scope. The following figure is an example of the display.
• FTE Status Auxiliary Remote Node displays the status of a remote FTE node's view of the FTE
connections. The following figure is an example.
8 www.honeywell.com
2 Installing FTE Status Display
Related topics
“Introduction” on page 10
“Installing FTE Status Server” on page 11
9
2 INSTALLING FTE STATUS DISPLAY
2.1 Introduction
The FTE Status Server is packaged and licensed with the Fault Tolerant Ethernet Driver and the System
Management software.
System Management Display
If you are viewing the FTE status display from a System Management console, you must build and configure a
system management display on at least one node within the multicast scope in order to view the FTE Status
Server and Auxiliary Display. Procedures for the following tasks are in the System Management Configuration
Guide.
• Installing System Management Display
• Creating a TPS Domain or Console
• Configuring a System Management Display
10 www.honeywell.com
2 INSTALLING FTE STATUS DISPLAY
Tip
Detailed instructions for installing and configuring the FTE driver software are in the FTE Planning, Installation
and Service Guide.
1 Launch the Honeywell installer by inserting the TPS System Software media or double-clicking Install from
the Package folder.
2 Select the appropriate package from the Install screen and click Next.
3 Review the Honeywell Software Installation - Welcome screen and click Next.
4 Review the Honeywell Software Installation - End User License Agreement screen and click Next.
5 Review the Honeywell Software Installation - Third Party Software Compatibility Policy screen and
click Next.
6 Complete the Honeywell Software Installation - User Information screen and click Next.
7 Select Fault Tolerant Ethernet Driver (FTE) and click Install Package.
8 From the Honeywell Software Installation - Installable Packages uncheck the Fault Tolerant Ethernet
Driver and leave the other selections checked.
9 Click OK.
10 Click Exit from the Installation window.
11
2 INSTALLING FTE STATUS DISPLAY
12 www.honeywell.com
3 FTE Status Server
Related topics
“Introduction” on page 14
“Using the FTE status display” on page 17
13
3 FTE STATUS SERVER
3.1 Introduction
Related topics
“About FTE status server” on page 14
“FTE status server display” on page 14
“FTE status component fields” on page 14
“Device status and information details” on page 15
Tip
The communication status of single interface heartbeat nodes has no bearing on the composite link status as viewed
from this display.
14 www.honeywell.com
3 FTE STATUS SERVER
Column Description
PID Process identification number
Comp Info Component information
ProgID Program identification
Device Status Composite link status of all FTE nodes being monitored. Refer the “Device status and
information details” on page 15 for description of when these states occur. Status states are
Running or Failed.
Device Info Specific device status information. The message in Device Information varies depending on the
reason for the device status state. Refer the “Device status and information details” on page 15
for description.
Attention
This status is only seen from an FTE node.
Failed FTE node has failed on Interface B All FTE nodes have at least their A -> B and B -> B
status states SILENT.
Attention
This status is only seen from an FTE node.
Failed FTE node has a Crosslink Failure All FTE nodes have at least their A -> B and B -> A
status states SILENT.
Attention
This status is only seen from an FTE node.
Failed Heartbeat Provider has stopped. FTE Status The Heartbeat Provider is no longer running, and the
cannot be determined. status of the FTE nodes cannot be determined. There is a
problem with the Heartbeat Provider on this node.
Failed Error occurred. See Event Log for details. An error that cannot be classified in one of the other
Need to restart FTE status server categories has occurred. There is a problem with the FTE
status server on this node. See the event log.
Failed Heartbeat Provider failed to start The FTE status server is unable to connect to the
Heartbeat Provider. There is a problem with the
Heartbeat Provider on this node.
Failed FTEIMDrv service installed but not in FTE driver is installed, but not running. There is a
running state problem with the FTE driver on this node.
Attention
If the driver is not installed, it is assumed the node
is a single interface node and no error is given.
15
3 FTE STATUS SERVER
16 www.honeywell.com
3 FTE STATUS SERVER
Tip
If you do not have a System Management Display configured, see the System Management Configuration
Guide.
17
3 FTE STATUS SERVER
6 Click OK.
The Node Administrator is displayed under the tree view.
7 Right-click the Node Administrator and choose Properties.
The Node Administrator Properties window is displayed.
18 www.honeywell.com
3 FTE STATUS SERVER
3.2.2 Change the view in the FTE Status Server details pane
Use the following procedure to change the way columns are displayed in the FTE Status details pane.
1 To reorder columns, select a column heading and drag it to the left or right of its original position.
Attention
You cannot change the position of the leftmost column in the details pane.
2 To resize columns, select the right or left border of the column heading and drag it to resize the column.
19
3 FTE STATUS SERVER
20 www.honeywell.com
4 FTE Status Auxiliary Display
Related topics
“Overview of FTE Status Auxiliary Display” on page 22
“Using the FTE Status Auxiliary Display” on page 25
“Monitoring Link Status from the Auxiliary Display” on page 26
“Viewing FTE Status Auxiliary Display of remote FTE node” on page 29
21
4 FTE STATUS AUXILIARY DISPLAY
22 www.honeywell.com
4 FTE STATUS AUXILIARY DISPLAY
Field Description
Dup State Duplicate detection state. Status states are:
• No Duplicates: normal state
• Duplicate Device Index
• Duplicate PdTag
• Both Duplicate PdTag and Device Index
Also Display Heartbeat Nodes Check this box to display single interface nodes that have the Heartbeat Provider
installed and are in the current multicast scope.
Attention
The composite status is provided to easily identify any single fault when the number of nodes exceeds the number of
currently displayed nodes. You must scroll down in the window and search each individual node to check if there is a
problem. If there is a red circle in the composite node status, it means that at least one node in the display is silent on
that particular communication path.
23
4 FTE STATUS AUXILIARY DISPLAY
Attention
The icon's purpose is to indicate simple network problems. Do not overanalyze the color of the icon to diagnose a
problem. Refer to the interface link status to determine the cause of the failure.
24 www.honeywell.com
4 FTE STATUS AUXILIARY DISPLAY
2 To reorder columns, select a column heading and drag it to the left or right of its original position.
Attention
You cannot change the leftmost column's position in the details pane.
3 To resize columns, select the right or left border of the column heading and drag it to resize the column.
25
4 FTE STATUS AUXILIARY DISPLAY
26 www.honeywell.com
4 FTE STATUS AUXILIARY DISPLAY
27
4 FTE STATUS AUXILIARY DISPLAY
28 www.honeywell.com
4 FTE STATUS AUXILIARY DISPLAY
29
4 FTE STATUS AUXILIARY DISPLAY
30 www.honeywell.com
5 Notices
Trademarks
Experion®, PlantScape®, SafeBrowse®, TotalPlant® and TDC 3000® are registered trademarks of Honeywell
International, Inc.
Trademarks
Experion®, PlantScape®, and SafeBrowse® are registered trademarks of Honeywell International, Inc.
Trademarks
Experion® and SafeBrowse® are registered trademarks of Honeywell International Inc.
PlantCruise™ is a trademark of Honeywell International Inc.
Other trademarks
Microsoft and SQL Server are either registered trademarks or trademarks of Microsoft Corporation in the
United States and/or other countries.
Trademarks that appear in this document are used only to the benefit of the trademark owner, with no intention
of trademark infringement.
31
5 NOTICES
32 www.honeywell.com
5 NOTICES
Pacific
Contact Honeywell Global TAC - Pacific
Phone 1300-364-822 (toll free within Australia)
+61-8-9362-9559 (outside Australia)
Facsimile +61-8-9362-9564
Mail Honeywell Limited Australia
5 Kitchener Way
Burswood, WA, 6100, Australia
Email GTAC@honeywell.com
India
Contact Honeywell Global TAC - India
Phone +91-20-6603-2718 / 19
1800-233-5051
Facsimile +91-20-6603-9800
Mail Honeywell Automation India Ltd.
56 and 57, Hadapsar Industrial Estate
Hadapsar, Pune - 411 013, India
33
5 NOTICES
Email Global-TAC-India@honeywell.com
Korea
Contact Honeywell Global TAC - Korea
Phone +82-80-782-2255 (toll free within Korea)
Facsimile +82-2-792-9015
Mail Honeywell Co., Ltd
4F, Sangam IT Tower B4-4 Block,
1590, DMC Sangam-dong, Mapo-gu,
Seoul 121-835, Korea
Email Global-TAC-Korea@honeywell.com
Singapore
Contact Honeywell Global TAC - South East Asia
Phone +65-6823-2215
Facsimile +65-6445-3033
Mail Honeywell Private Limited
Honeywell Building
17, Changi Business Park Central 1
Singapore 486073
Email GTAC-SEA@honeywell.com
Japan
Contact Honeywell Global TAC - Japan
Facsimile +81-3-6730-7228
Mail Honeywell K.K
New Pier Takeshiba, South Tower Building,
20th Floor, 1-16-1 Kaigan, Minato-ku,
Tokyo 105-0022, Japan
Email Global-TAC-JapanJA25@honeywell.com
34 www.honeywell.com
5 NOTICES
http://www.honeywellprocess.com/
Elsewhere
Contact your nearest Honeywell office.
35
5 NOTICES
36 www.honeywell.com