Professional Documents
Culture Documents
Ed81w Oled65g8pla
Ed81w Oled65g8pla
Ed81w Oled65g8pla
OLED TV
SERVICE MANUAL
CHASSIS : ED81W
MODEL : OLED65G8PLA
CAUTION
BEFORE SERVICING THE CHASSIS, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
Copyright © 2018 LG Electronics Inc. All rights reserved. Only training and service purposes.
CONTENTS
CONTENTS ............................................................................................... 2
SPECIFICATION ....................................................................................... 6
SYSTEM EEPROM
R USB1 (2.0) OCP 1.5A I2C 4 (256Kb)
E
A USB2 (2.0) OCP 1.5A USB
R
IC101 eMMC
CI USB3 (2.0) OCP 1.5A (8GB)
1. O18 Circuit Block Diagram
O18
TS 51P
VBY1 41P
HDMI1 (2.0)
- 11 -
Sub Board
R HDMI2 (2.0)
E (ARC) AUD_LRCH Audio AMP 1
HDMI Front
A HDMI3 (2.0) (NTP7515D)
R Depending on model 0X54
HDMI4 (2.0)
CVBS/L/R AV Audio AMP 2 Woofer
BLOCK DIAGRAM
R AUD_LRCH
Copyright ©
(NTP7515D)
E LAN ETHERNET YPbPr COMP 0X56
A
R
AUD_LRCH_TW
Audio AMP 3 Tweeter
AMP H/P (NTP7515D)
BLUTOOTH Line-Out 0X54
USB_WIFI-BT TI
WIFI
SUB LED I2S
ASSY IR SPDIF OUT OPTIC
LNB2_OU
T
+3.3V_DEMOD
LNB2_OUT
- 12 -
I2C_SDA/SCL_3_Demod SCL_Demod
SDA_Demod
I2C_SDA/SCL_5_TU SCL_RF
SDA_RF
Copyright ©
TU_CVBS_SOC CVBS
IF_AGC
IF_AGC
TU_SIF_TU
SIF
A 1
AV
AV1 Jack Side SOC Side
ACK
Phone JACK Main IC
AV_CVBS_IN AV1_CVBS_IN_SOC
AR15 [CVBS_IN2]
AR10 [AUAD_L_CH2_IN
COMP2/AV_L_IN AUAD_L_CH2_IN AT10 [AUAD_R_CH2_IN]
COMP2/AV_R_IN AUAD_R_CH2_IN
Component 1
Phone JACK COMP2_SOG2_IN_SOC
COMP2_Y_IN_SOC AR12 [SOY1_IN]
COMP2_Pb_IN_SOC AT12 [Y1_IN]
COMP2_Pb AR13 [PB1_IN]
COMP2_Pr_IN_SOC
COMP2_Y AU14 [PR1_IN]
4. Video & Audio IN/OUT
COMP2_Pr
Front Speaker
Audio AMP
[SCK]
[LRCK]
[DACLRCH]
- 14 -
[I2C_SCL_0/SDA_0]
Woofer
[GPIO17]
Speaker
Audio AMP AMP_RESET
Copyright ©
Tweeter
Speaker
[DACSLRCH(I2S DATA)]
Audio AMP [I2C_SCL_4/SDA_4]
AMP_MUTE
(WOOFER_MUTE) MICOM
SPDIF OUT
SPDIF_OUT
ARC OUT
(HDMI2) SPDIF_OUT_ARC
AL34 [ARC_OUT]
CEC_REMOTE
+5V
Port_1
HDMI 1 [HDMI2_1_SDA]
DDC_I2C_1 HDMI2.0 HDCP1.4
(2.0)_V [HDMI2_1_SCL]
LGE PHY HDCP2.2
HDMI_HPD_1
[HDMI2_1_HPD]
CEC_REMOTE
+5V
HDMI 2 Port_2
[HDMI2_2_SDA]
(2.0)_V DDC_I2C_2 HDMI2.0 HDCP1.4
[HDMI2_2_SCL]
ARC LGE PHY HDCP2.2
HDMI_HPD_2
[HDMI2_2_HPD]
SPDIF_OUT_ARC
[PHY0_ARC_OUT]
- 15 -
CEC_REMOTE
+5V
Port_3
HDMI 3 [HDMI2_3_SDA]
DDC_I2C_3 HDMI2.0 HDCP1.4
(2.0)_V [HDMI2_3_SCL]
LGE PHY HDCP2.2
HDMI_HPD_3
[HDMI2_3_HPD]
SPDIF_OUT_ARC
Copyright ©
CEC_REMOTE
+5V
Port_4
HDMI 4 [HDMI2_4_SDA]
(2.0)_V DDC_I2C_4 HDMI2.0 HDCP1.4
[HDMI2_4_SCL]
LGE PHY HDCP 2.2
HDMI_HPD_4
[HDMI2_4_HPD]
USB_CTL3 (2.0)_V
[SPI_DO1] OCP BD224G
IR + Wi-Fi /BT
WIFI_DP / DM
[USB2_2_DP0 / DM0] Wafer 14P
P4000
- 16 -
COMBO_RESET
BT_WAKEUP_DEVICE +3.5V_WIFI
BT_WAKEUP_HOST
WIFI_EN
MICOM
IC3000 WOL/WIFI_POWER_ON
Copyright ©
SOC_RX/TX
SOC_RX/TX UART wafer
P10001
[UART0_RXD/GPIO106]
SOC_RX/TX
[UART0_TXD/GPIO105]
430
413
900
T-Con Board
571
200T
570
431
414
821
120
811
530
411
531
421
500
820
501
830
540
423
812
121
550
422
551
412
552
870
860
850
840
400
LV1 LV2
310
AR2
200
1-1
Rear Side
1-1 1-1
Cover, Rear
1-2
2-2
Cover Ass’y, Glass Cover, FPC Cable Outer
Rear View
Cable
2-2
2-2 2-2
3-1
Upper Corners
spatula
3-1 3-1
3-1 3-1
Direction
CAUTION!
Front View
3-1 3-1
Direction
CAUTION!
3-2
Concept Image
Module
※ CAUTION
If the module is pulled more than necessary, damage to the PEM-nut of the glass assembly or module bending may occur.
So, Pull the Module out only to get away magnets at bottom of module slightly(About 30mm) from glass except 5 magnets at top side of
module.
300mm
Magnet attach points at top side
Magnet attach points at bottom side
30mm
Concept Image
Module
4-2 4-3
Cable Upper
Corners
Bottom
Corners
3-4 3-4
Double-sided
tape
3-4 3-4
Double-sided
tape
5-1 5-2
O X
6-2
7-2
Power Cord
Rear Direction based on Set
8-1 8-1
8-1 8-1 8-1
8-1 8-1
8-1
8-2
9-2
Front View of Box Assy, AIO
※ Notice
When assemble Cover Assy, AIO Top Cover Assy, AIO Top
First, Connect 4P Harness and 12P Harness.
Second, Slide the Cover Assy, AIO Top as shown below picture. NG OK
Joystick PCB
Harness
11-2
12P Harness
4P Harness
12-1 12-2
P201
12-1
13-1 13-2
13-1 13-1 13-1
13-2 13-2
14-1
14-2
14-2 14-2
FFC Cable
Open the
Clip 14-2 14-2
P10006
15-2
15-1 15-1
15-1
15-1
11-1
15-1 15-1
15-1
16-1
T-Con 2 in 1 Cable
BLACK
11-1 WHITE
17-2
T-Con “A”
17-3 17-1
T-Con 2 in 1 Cable
BLACK
WHITE
T-Con “B”
18-1
18-1
18-1
18-1
18-1 18-1
Gap Pad
Gap Pad
Gap Pad
Gap Pad
2-2
2-2
2-2
2-2
2-2
2-2 2-2
3-1
3-2
3-1
3-3
T-Con 2 in 1 Cable
WHITE 3-4
BLACK
3-4 3-4
4-1
4-2
4-2 4-2
4-2
4-2
11-1
4-2
4-2
4-2
MARKING
4-2 4-2
4-2
4-1
4-2 4-3
4-2
4-2
FFC Cable
4-2
4-5
4-4 4-4
11-1
5-1 5-1
FFC Cable
5-1 5-1
5-2
Close the
Clip
FFC Cable
5-3
5-3
6-1 6-1
7-2
7-2
P1001
P10002
7-2
P201
7-3
7-1
P251
7-1
Power Cord
8-1
12P Harness Cover Ass’y, AIO Top
8-2
9-1
Front View of Box Assy, AIO
9-2
10-1
Joystick PCBA Cover Assy, AIO Rear
Harness
10-2
: Main Management Latch Point 2EA)
※ Push the all Latch into AIO Box until connection sound(tick) is occurred
Especially, Latch Point 2EA
: Normal Latch Point 14EA)
8-1
8-1 8-1
8-1 8-1 8-1
8-1 8-1
8-1
12-2
O X
13-1 HOOK
13-2 LATCH
14-1 14-1
Stick here
14-2
Double sided Tape
NG
Stick here
OK
Rub the double sided
PET Release tape(MDS65738356)
to reveal BK Print color.
14-2 14-2
< Status of Double Sided Tape attached on Glass>
Copyright © 2018 LG Electronics. Inc. All rights reserved.
Only for training and service purposes.
OLED65G8(W8K) Working Guide Concept Image
A A
B B
Front View of
Cover Ass’y Glass Rear View of Module
Front View
Cable
B
15-2
Module
Front View
Rear
View
16-1 16-1
16-2
16-3
Release Film
Front View
Rubbing Region
[Metal Part & Panel]
Rubbing Region
[Metal Part & Panel]
Double-
sided Tape
Panel Double-
sided Tape
Panel Cover,
Module
Cover,
Module
17-1
17-2
Rear Side
17-2 17-2
Cover, Rear
17-1
8-1 8-1
(1) Hold the AIO Box by placing your hand in the gap on the back of the Bottom Packing.
(2) Supporter the side area of the head with your other hand, tilt it back, and lift the set out of the packing.
1 2
Back View
of the Set
(3) Insert FPC Holder Bracket with FPC Cable into the Connection Cable Jack of AIO Box Rear Cover.
3 Rear View
(4) Fasten the screw 2EA on the FPC Holder Bracket to the AIO Box Rear Cover.
(5) Tilt the Set forward and Put the Set to the position you want in the same way as (1) & (2).
4 Rear View
4 4
※ CAUTION
Do not grab the Front Décor on the front of the Set. Do not press the Grille section (especially the voice output section) of the Front Décor.
1 No video/Normal audio 1
2 No video/No audio 2
4 Color error 4
First of all, Check whether there is SVC Bulletin in GSCS System for these model.
Copyright © 2018 LG Electronics. Inc. All rights reserved.
Only for training and service purposes.
Standard Repair Process
Established
Error A. Video error date
OLED TV symptom
No video/ Normal audio Page No 1/16
First of all, Check whether all of cables between B/D are inserted properly or not.
(Main B/D↔ Power B/D, Vx1 Cable, Speaker Cable, IR B/D Cable. etc)
☞A1 ☞A9
No video Normal Y Check Vx1 lock Y Check Power B/D Normal Y
Normal audio 0V Replace Main B/D
audio voltage (Main) voltage
20V, 12V etc.
N ☞A9 N N
Move to No Check Power B/D (Module) 24V, 12V output Repair Power B/D
video/No audio or parts
Normal Y
Replace Module
voltage
& T-CON B/D
N End
Replace Power
B/D or repair
parts
※Precaution
☞A4 (S/W version)
☞A2 (White Balance)
Always check & record S/W Version and White
Replace Main B/D Re-enter White Balance value
Balance value before replacing the Main B/D
1
Copyright © 2018 LG Electronics. Inc. All rights reserved.
Only for training and service purposes.
Standard Repair Process
Established
Error A. Video error date
OLED TV symptom
No video/ No audio Page No 2/16
☞A9
Check various voltages Check and
Y
No Video/ of Power B/D (Main) Normal
replace
No audio (20V, 12V…) voltage?
Main B/D
N
End
Replace Power
B/D or repair parts
2
Copyright © 2018 LG Electronics. Inc. All rights reserved.
Only for training and service purposes.
Standard Repair Process
Established
Error A. Video error date
OLED TV symptom
Picture broken/ Freezing Page No 3/16
☞ A4
Check RF Cable
Normal Y Check SVC N Check Y
Connection Close
1. Reconnection Picture? S/W Version Bulletin? Tuner soldering
2. Install Booster N
N Y
S/W Upgrade
N Contact with signal distributor
Normal
Picture? or broadcaster (Cable or Air)
Normal N
Y Picture? Replace
Main B/D
Y
Close
Close
3
Copyright © 2018 LG Electronics. Inc. All rights reserved.
Only for training and service purposes.
Standard Repair Process
Established
Error A. Video error date
OLED TV symptom
Color error Page No 4/16
☞ A7
☞A19 ※ Check
and replace
Check color by Internal Color Y Link Cable Color Y Color Y
Replace Main B/D Replace Module & T-CON B/D
Pattern error? (Vx1) and error? error?
contact
N condition N N
Check
External device Y
External Input external
/Cable Replace Main B/D
error device and
normal
cable
N
Request repair
for External
device/Cable
4
Copyright © 2018 LG Electronics. Inc. All rights reserved.
Only for training and service purposes.
Standard Repair Process
Established
Error A. Video error date
OLED TV symptom Vertical / Horizontal bar, residual image,
light spot, external device color error Page No 5/16
☞A19 ☞ A7 N
Check external
Check and
Check color by Internal Screen Y device Y Screen N Screen
Normal? replace Link Replace Main B/D
Pattern normal? connection normal? normal?
Cable
condition
N N Y Y
Y
Connect other external device
and cable.
HDMI/ Check normal operation of Screen N Replace
Normal N DVI External Input(HDMI/DVI) by normal? Main B/D or
screen? error connecting Jig, pattern Module & T-CON
Generator ,Set-top Box etc. B/D
Y
End
5
Copyright © 2018 LG Electronics. Inc. All rights reserved.
Only for training and service purposes.
Standard Repair Process
Established
Error B. Power error date
OLED TV symptom
No power Page No 6/16
☞A8
DC Power on
Check Power LED Y Normal Y
by pressing Power Key End
Logo LED On? operation?
On Remote control
. Stand-By: Red light on
N N
. Operating: Turn Off
Check Power cord
was inserted properly
☞A9
Y Measure voltage of each output
Normal? of Power B/D
N
. Stand-By: Red light on
Replace Power B/D
. Operating: Turn Off
. Abnormal Case : LED blinking
-AM_MODE : orange light
-FAN or High Temperature : blue light
6
Copyright © 2018 LG Electronics. Inc. All rights reserved.
Only for training and service purposes.
Standard Repair Process
Established
Error B. Power error date
OLED TV symptom
Off when on, off while viewing, power auto on/off Page No 7/16
Check outlet
☞A10 ☞8-A/B
N Y
Check A/C cord Check Power On/Off CPU
Error? Replace Main B/D Normal? End
Status Abnormal
N
Check for all 2- phase
power out Y Replace Power B/D
Abnormal
INV_Error
☞A9
(If Power On/Off
Status is not Normal Y
Replace Main B/D
displayed) voltage?
Check Power B/D
voltage N
※ Caution
Check and fix exterior Replace Power B/D
of Power B/D Part
7
Copyright © 2018 LG Electronics. Inc. All rights reserved.
Only for training and service purposes.
Standard Repair Process
Established
Error B. Power error date
OLED TV symptom
Off when on, off while viewing, power auto on/off Page No 8-A/16
Please refer to the all cases which can be displayed on power off mode.
Power Off list Explanation Action contents
Power off by CPU Abnormal status
1. Power off (Last Cold, Last Cool, Last Warm)
CONDITION : When power on and checking Power on Mode, abnormality appears.
POWER_OFF_BY_CPU_ABNORMAL Check & Change Main B/D
2. Power off in CPU Abnormal Case (Exception)
- Release Mode : Reboot
- Debug/Event Mode : Power off
POWER_OFF_BY_CPUCMD Power off by main SoC command. Check & Change Main B/D
Case1 : Pipe line overflow
POWER_OFF_BY_ABN Check & Change Main B/D
Case2 : reboot to suspend Fail
Power off when TV is not turned off during a certain time
RESULT : micom force to trigger TV power off.
POWER_OFF_BY_KEYTIMEOUT Check & Change Main B/D
CONDITION : When pressing power key while power on/off status, CPU does not response within 8
seconds or call the WDT timer API.
Power off by not detecting AC (abnormal case) Normal Case
POWER_OFF_BY_ACDET RESULT : micom triggers TV power off
CONDITION : Power detect port drops to low while power on status. Check & Change Main B/D
Power off by not unstable AC power detect.
RESULT : micom check the stable power.
POWER_OFF_BY_5VMNT Check & Change Main B/D
CONDITION : When AC on or DC on, stabilization check routine (Power Detect High Check) fail after
multi power on.
Power off when receiving no ack
Debug Status : Release Mode
POWER_OFF_BY_NO_POLLING RESULT : TV power off/on (Reboot) Check & Change Main B/D
CONDITION : There is no I2C response from CPU for 15 seconds.
==> if warm standby, power off occurs.
similar with POWER_OFF_BY_KEYTIMEOUT, but different concept.
RESULT : micom force to trigger TV power off within 4 seconds.
POWER_OFF_BY_REMOTE_KEY2 Check & Change Main B/D
CONDITION : When TV power on/off, CPU does not response within 4 seconds, and then pressing
power key.
Check & Change OLED Module
POWER_OFF_BY_INV_ERROR Power off by LCD Module inverter error (OLED)
& T-CON B/D
RESULT : Reboot Check & Change OLED Module
POWER_OFF_BY_ONRF_FAIL
CONDITION : OLED Module compensation is running but fails. & T-CON B/D
Check & Change OLED Module
POWER_OFF_BY_PNWASHFAIL Power off by panel noise wash function fail case. (OLED)
& T-CON B/D
Power off by resume fail when dc on case.
POWER_OFF_BY_RESUME_FAIL Check & Change Main B/D
If occur the resume fail, TV will be rebooted.
Check whether Module cable
POWER_OFF_BY_OLED_AM_MODE If the Module cable is disconnected, the micom is forced to power off TV. is connected
If still occurs , change
Module & T-CON B/D
8-A
Copyright © 2018 LG Electronics. Inc. All rights reserved.
Only for training and service purposes.
Standard Repair Process
Established
Error B. Power error date
OLED TV symptom
Off when on, off while viewing, power auto on/off Page No 8-B/16
Please refer to the all cases which can be displayed on power off mode.
Power Off list Explanation Action contents
Power off by Micom Reset
POWER_OFF_BY_RESET It's not recommend. Please use POWER_OFF_BY_REQUEST_RESET.
RESULT : Reset the TV and init time data.
POWER_ON_BY_REMOTE_KEY Power on by remote Power Key.
POWER_OFF_BY_OFF_TIMER Power off by Off timer
POWER_OFF_BY_SLEEP_TIMER Power off by sleep timer
POWER_OFF_BY_INSTOP_KEY Power off by Instop Key
Power off by auto off function
POWER_OFF_BY_AUTO_OFF 1. When it lasts for 15 minutes that no signal and no remote key input.
2. When screen mute status lasts for 2 hours.
Power off by On timer
POWER_OFF_BY_ON_TIMER
Power off when no remote and local key input for 2 hours after power on by On timer.
POWER_OFF_BY_RS232C Power off by RS232C command
Power off by reserved recording Normal Case
POWER_OFF_BY_RESREC Power off automatically after recording finishes after TV turns on by reservation
recording from power off status.
POWER_OFF_BY_SWDOWN Power off by software download
POWER_OFF_BY_LOCAL_KEY Power off by local key
RESULT : Power off
POWER_OFF_BY_COMP_END
CONDITION : OLED threshold voltage degradation completes.
POWER_OFF_BY_HDMI_CEC Power off by HDMI CEC command
POWER_OFF_BY_PNWASHSTA
Power off for starting OLED panel noise function in warm state.
RT
POWER_OFF_BY_PNWASHDON
Power off by panel noise wash function complited. (OLED)
E
POWER_OFF_BY_COOLING Power off for cool down the OLED t-con. (OLED)
POWER_OFF_BY_EDID_WRITE Power off by EDID write done.
Established
Error C. Audio error date
OLED TV symptom
No audio/ Normal video Page No 9/16
☞A11 ☞A12
No audio
Check Sound N Check audio B+
Normal Y
menu > Normal 20V of Power B/D
Screen normal voltage
Sound Test
Y N
Check Sound out Setting Replace Power B/D and repair parts
Check N
Disconnection Replace Main B/D End
Speaker
or Sub B/D
disconnection
Y
Replace Speaker
9
Copyright © 2018 LG Electronics. Inc. All rights reserved.
Only for training and service purposes.
Standard Repair Process
Established
Error C. Audio error date
OLED TV symptom
Wrecked audio/ discontinuation/noise Page No 10/16
☞A12
Wrecked audio/
Check and replace
Discontinuation/ Normal N Check audio
speaker and
Noise for audio? B+ Voltage (20V)
connector
Check input all audio
signal Y
Signal Y
-RF
normal? Y
-External Input Normal
signal voltage?
N Wrecked audio/ End
Discontinuation/ N
Noise Replace Main B/D
for DTV or ATV
Replace Power B/D
10
Copyright © 2018 LG Electronics. Inc. All rights reserved.
Only for training and service purposes.
Standard Repair Process
Established
Error D. Funtion error date
OLED TV symptom
Remote control checking Page No 11/16
11
Copyright © 2018 LG Electronics. Inc. All rights reserved.
Only for training and service purposes.
Standard Repair Process
Established
Error D. Funtion error date
OLED TV symptom
MR18 operating checking Page No 12/16
MR18 (Magic Remocon) operating error
☞A4
Check the RF Receiver ver N Check MR18 Normal Y Press the Is show ok N Turn off/on the set
INSTART menu is “00.00”? itself Operation operating? wheel message? and press the
wheel
N Y
Y
☞A14
Check & Replace
Check & Repair Battery of MR18 Close
RF assy
connection
☞A4 Normal Y
operating? Close
RF Receiver ver N Is show ok N Press the back key
is “00.00”? Close
message? about 5sec
N
Y
Y Replace
MR18
Down load the Firmware
Close
* INSTART MENU12.RF
Remocon Test Receiver
•If you conduct the loop at 3times,
Firmware download
change the MR18.
12
Copyright © 2018 LG Electronics. Inc. All rights reserved.
Only for training and service purposes.
Standard Repair Process
Established
Error D. Funtion error date
OLED TV symptom
Wifi operating checking Page No 13/16
☞A4 ☞A14
Check the Wi-Fi Mac value N Check the Wifi wafer Normal N Replace
INSTART menu is “NG”? Pin #1 Voltage? Main B/D
Y
☞A14 Y
☞A4
Wi-Fi Mac value N
is “NG”? Close
13
Copyright © 2018 LG Electronics. Inc. All rights reserved.
Only for training and service purposes.
Standard Repair Process
Established
Error D. Funtion error date
OLED TV symptom
External device recognition error Page No 14/16
Check technical
Check Y
Signal information Technical N External Input
input Replace Main B/D
input? - Fix information information? Recognition error
signal
- S/W Version
N Y
HDMI/
Check and fix DVI, Optical
Fix in Replace Main B/D
external device/cable Recognition error
accordance
with technical
information
14
Copyright © 2018 LG Electronics. Inc. All rights reserved.
Only for training and service purposes.
Standard Repair Process
Established
Error E. Noise date
OLED TV symptom
Circuit noise, mechanical noise Page No 15/16
Identify Check
Circuit
noise location of Replace PSU or Main B/D
noise
type noise
15
Copyright © 2018 LG Electronics. Inc. All rights reserved.
Only for training and service purposes.
Standard Repair Process
Established
Error F. Exterior defect date
OLED TV symptom
Exterior defect Page No 16/16
Remote
control Replace remote control
damage
AV Box
Replace AV Box
damage
16
Copyright © 2018 LG Electronics. Inc. All rights reserved.
Only for training and service purposes.
Contents of Standard Repair Process Detail Technical Manual
R7624 : 0[V]
Check a voltage of R7624 after turn on the TV. Check a voltage of R7632 after turn on the TV.
If the voltage is low, Vx1 is locked.(OK) If the voltage is high(3.3V), BDP issue.(NG)
Entry method
All Settings Programmes Programme Tuning & setting When the signal is strong, use the
Manual Tuning Antenna DTV attenuator (-10dB, -15dB, -20dB etc.)
Version
Checking method:
1. Check the signal strength or check whether the screen is normal when the external device is connected.
2. After measuring each voltage from power supply, finally replace the MainB/D.
A5
Copyright © 2018 LG Electronics. Inc. All rights reserved.
Only for training and service purposes.
Standard Repair Process Detail Technical Manual
Error A. Video error _Vertical/Horizontal bar, Established
OLED TV symptom residual image, light spot date
Content Connection diagram Page No A6
A6
Copyright © 2018 LG Electronics. Inc. All rights reserved.
Only for training and service purposes.
Standard Repair Process Detail Technical Manual
Error Established
symptom A. Video error_Color error date
OLED TV
Content Check Link Cable (Vx1) reconnection condition Page No A7
Check the contact condition of the Link Cable, especially dust or mis-insertion.
Color Error
Symptom
Item Cause Symptom Image
Name
Pin 단선
A - 1/10
Copyright © 2018 LG Electronics. Inc. All rights reserved.
Only for training and service purposes.
Appendix. Examples of Symptoms(Image error) Check for poor cable contact
Symptom
Item Cause Symptom Image
Name
A - 2/10
Copyright © 2018 LG Electronics. Inc. All rights reserved.
Only for training and service purposes.
Appendix. Examples of Symptoms(Main) Check parts by symptom
Symptom
Item Cause Symptom Image
Name
A - 3/10
Copyright © 2018 LG Electronics. Inc. All rights reserved.
Only for training and service purposes.
Appendix. Examples of Symptoms(Main) Check parts by symptom
Symptom
Item Cause Symptom Image
Name
A - 4/10
Copyright © 2018 LG Electronics. Inc. All rights reserved.
Only for training and service purposes.
Appendix. Examples of Symptoms(Main) Check parts by symptom
Symptom
Item Cause Symptom Image
Name
Right-side
Main
Screen Right-side screen problem
problem
LG logo
Main Screen picture spread problem
Screen problem
A - 5/10
Copyright © 2018 LG Electronics. Inc. All rights reserved.
Only for training and service purposes.
Appendix. Examples of Symptoms(Module) Check parts by symptom
Symptom
Item Cause Symptom Image
Name
Un-repairable Cases
Module Vertical bar
In this case please exchange the Module
A - 6/10
Copyright © 2018 LG Electronics. Inc. All rights reserved.
Only for training and service purposes.
Appendix. Examples of Symptoms(Module) Check parts by symptom
Symptom
Item Cause Symptom Image
Name
Un-repairable Cases
Module Press damage
In this case please exchange the Module
A - 7/10
Copyright © 2018 LG Electronics. Inc. All rights reserved.
Only for training and service purposes.
Appendix. Examples of Symptoms(Module) Check parts by symptom
Symptom
Item Cause Symptom Image
Name
A - 8/10
Copyright © 2018 LG Electronics. Inc. All rights reserved.
Only for training and service purposes.
Appendix. Examples of Symptoms(Module) Check parts by symptom
Symptom
Item Cause Symptom Image
Name
Burnt
Module Burnt
(Can’t fix it)
Screen Mura
Module Mura
(Can’t fix it)
A - 9/10
Copyright © 2018 LG Electronics. Inc. All rights reserved.
Only for training and service purposes.
Appendix : Exchange Power B/D (PSU)
No Light No picture/Sound Ok
A – 10/10
Copyright © 2018 LG Electronics. Inc. All rights reserved.
Only for training and service purposes.
Standard Repair Process Detail Technical Manual
Error Established
symptom B. Power error _No power date
OLED TV
Content Check front display LED Page No A8
No power
A8
Copyright © 2018 LG Electronics. Inc. All rights reserved.
Only for training and service purposes.
Standard Repair Process Detail Technical Manual
Error Established
symptom
B. Power error _No power
OLED TV date
Content Check power input Voltage & ST-BY 3.5V Page No A9
P251
P201
Power To
Module
No video/ Normal audio No video/ No audio No power Off when on, Remote control
off while viewing & Local switch checking
A9 power auto on/off
Copyright © 2018 LG Electronics. Inc. All rights reserved.
Only for training and service purposes.
Standard Repair Process Detail Technical Manual
Error
symptom B. Power error _Off when on, off whiling viewing Established
date
OLED TV
Content POWER OFF MODE checking method Page No A10
Entry method
Checking method
1. Press the Setting button on the remote control
2. Select the Sound function of the Menu
3. Select the Sound Out
4. Select Internal TV Speaker
1 SPK_R-_FT 2 SPK_R+_FT
3 SPK_L-_FT 4 SPK_L+_FT
P201
5 SPK_R-_CT 6 SPK_R+_CT
7 SPK_L-_CT 8 SPK_L+_CT
9 SPK_R-_TW 10 SPK_R+_TW
11 SPK_L-_TW 12 SPK_L+_TW
Connect the tester to the speaker terminal and if you hear the “Chik Chik” sound when you touch
the GND and output terminal, the speaker is normal.
A12 No audio/ Normal video
③ 5 NC 6 LED_Blue
7 NC 8 3.5V_ST
9 GND 10 LED_Red
11 LED_Green 12 GND
13 SCL 14 SDA
15 GND 16 IR
17 NC 18 NC
Eye LED IR
Check IR cable condition between IR & Main B/D.
Check the st-by 3.5V on the terminal.
Remote control
& Local switch checking
A13
Copyright © 2018 LG Electronics. Inc. All rights reserved.
Only for training and service purposes.
Standard Repair Process Detail Technical Manual
Error Established
symptom D. Function error date
OLED TV
Content Motion remote/WIFI operation checking method Page No A14
14Pin
1 3.5V_WIFI
2 WIFI_DM
3 WIFI_DP
4 GND
5 WOL/WIFI_POWER_ON
Wifi & BT Rear 6 3.5V_WIFI
7 COBO_RESET
8 GND
9 BT_WAKEUP_DEVICE
10 BT_WAKEUP_HOST
11 GND
12 NC
13 NC
14 NC
Check WIFI Combo cable condition between WIFI Combo Assy & Main B/D.
Check the 3.5V_WIFI on the terminal 1 & 6
0 4 1 3
0 4 1 3
A15
Copyright © 2018 LG Electronics. Inc. All rights reserved.
Only for training and service purposes.
Standard Repair Process Detail Technical Manual
Error Established
symptom E. ETC date
OLED TV
Content How to use the Service remote control Page No A16
[ETC] Each time pressing the KEY button, Mode gets changed to ETC and P-ONLY each time
Simplink (Added
Access to the Simplink-connected device
Function)
TILT Used for screen tilting change (Access to the old PDP control mode)
A16
Copyright © 2018 LG Electronics. Inc. All rights reserved.
Only for training and service purposes.
Standard Repair Process Detail Technical Manual
Error Established
symptom E. ETC date
OLED TV
Content How to use the Service remote control Page No A17
B-TOOTH
Connected to Blue-Tooth
(Added function)
Model Nam ex) 42PG60D-NA Current Model Name S/W Version ex)
IN-START V03.11.0 Current S/W version
MICOM Version ex) V3.05.0 current Mi-Com version UTT ex) User TV total usage time
CH + - Channel Up/Down
HDMI1,2,3,4
Connects to HDMI 1,2,3,4
(Add function)
A17
Copyright © 2018 LG Electronics. Inc. All rights reserved.
Only for training and service purposes.
Standard Repair Process Detail Technical Manual
Error Established
symptom E. ETC date
OLED TV
Content Check items after Main B/D replacement Page No A18
A18
Copyright © 2018 LG Electronics. Inc. All rights reserved.
Only for training and service purposes.
Standard Repair Process Detail Technical Manual
Error Established
symptom
A. Video error_Color error
OLED TV date
Content Adjustment OLED Test pattern Page No A19
Checking order
1. Check LED Color Orange
2. Unplug the power cord
3. Reconnect Cable to AV Box(or Extension Cable)
4. Plug the power cord No power
A20
Copyright © 2018 LG Electronics. Inc. All rights reserved.
Only for training and service purposes.
Standard Repair Process Detail Technical Manual
Error Established
symptom
B. Power error_ No power
OLED TV date
Content Check front display LED(Blinking Blue Color LED) Page No A21
2-1 Poweronly
Temp.
Sensor
Checking order
1. Check LED color Blue
2. Check FAN Stauts (Poweronly mode or Instart > OLED)
3. Replace FAN or Temperature Sensor.
A21 No power
24Pin
13Y/14Y 28Pin
No Marking
OLD JIG
17/18Y
W7 17Y/18Y
B8 (OLED)
24Pin 12Y C8
E8 24Pin
18Y
G8
32LK61/32LK62
W8
43/49LK61
18Y
18Y
UK63/UK64
SK80/UK89
UK65/UK7050
SK85/SK96
SK95/SK99 16Y/17Y/18Y
18Pin (UH/UJ/UK
18Y SK)
24 Marking Check 28Pin UK74
28Pin 12Pin 12Pin 28Pin
UK75
Cable Connection UK78
Includes 49UJ63 SK79
17Y/18Y 16/18Y 16Y/17Y/18Y 16Y/17Y 16Y
(SJ/UJ/UK/SK) (UH/UK) (LH/LJ/LK) (UH/SJ) (UH)
Copyright © 2018 LG Electronics. Inc. All rights reserved.
Only for training and service purposes.
Power Board Muitl Gender JIG Diagnostic model List
Existing 12Y, 13Y, 14Y, 15Y LED models included
15Y, 16Y, 17Y/18Y OLED, 16/17/18 Y LED model Power diagnosis function newly added
<15Y/16Y/17Y/18Y OLED Model, 16Y/17Y/18Y LED Model>
Year Product Model
EG92/EG93/EG94
‘15 OLED EG96
EF95
B6, C6
OLED
E6, G6
UH95/UH96
‘16 UH85/UH93
UH77/UH87
LED
UH75/UH76
UH65/UH68
LH68, LH66, LH60,LH54
B7, C7
‘17 OLED E7, G7
W7
SJ95/UJ98
SJ85/UJ94
SJ80, UJ77
UJ75/UJ78
’17 LED
UJ65/UJ68
UJ63/UJ67
LJ61/LJ68
LJ55/LJ58
SK80/SK85/SK95
UK78/UK75/SK79
‘18 LED
UK63/UK64/UK65/UK7050
32LK61/62, 43/49LK61
B8, C8, E8
‘18 OLED
G8, W8
1 2
※ Note on set up
(The correct power diagnosis can be made only if it is set correctly.)
- 24V Power Board : Change the switch to 24V of Smart Jig Voltage
- 20V Power Board : Change the switch to 24V of Smart Jig Voltage
- 13.2V/18V Power Board : Change the switch to 24V of Smart Jig Voltage
24V 24V
20V 20V
13.2V/18V 24V
1 2
3 4
▶ Disconnect the Main Board 24Pin Power Cable connector. ▶ Connect the 24Pin Power Cable connector to the Muitl
Gender JIG 24Pin connector
5 6
1 2
1 2
▶ Check power board voltage. ▶ Disconnect the Main Board 24Pin Power Cable connector.
▶ Smart JIG: Fix the LCD MODEL switch to 24V.(Smart JIG)
3 4
▶ Connect the 24Pin Power Cable connector ▶ When the OK LED(24V,12V) turns on, Power Board is normal.
to the Muitl Gender JIG 24Pin connector
1 2
▶ Check power board voltage. ▶ Disconnect the Main Board 24Pin Power Cable connector.
▶ Fix the LCD MODEL switch to 24V.(Smart JIG)
3 4
▶ Connect the 24Pin Power Cable connector ▶ When the OK LED(24V,12V) turns on, Power Board is normal.
to the Muitl Gender JIG 24Pin connector ▶ When the NG LED turns on, the Power Board
can be judged as defective.
Copyright © 2018 LG Electronics. Inc. All rights reserved.
Only for training and service purposes.
`16Y OLED(G6) Power Board Diagnostic method
1 2
▶ Check power board voltage. ▶ Disconnect the Main Board 24Pin Power Cable connector.
▶ Fix the LCD MODEL switch to 24V.(Smart JIG)
3 4
▶ Connect the 24Pin Power Cable connector ▶ When the OK LED(24V,12V) turns on, Power Board is normal.
to the Muitl Gender JIG 24Pin connector ▶ When the NG LED turns on, the Power Board
can be judged as defective.
Copyright © 2018 LG Electronics. Inc. All rights reserved.
Only for training and service purposes.
`17Y OLED(B7/C7/E7/G7) Power Board Diagnostic method
1 2
▶ Disconnect the Main Board 28Pin Power Cable connector. ▶ Connect the 28Pin Power Cable connector
to the Muitl Gender JIG 28Pin connector
3 4
▶ Switch the LCD MODEL S/W to 20V by checking ▶ When the OK LED(24V,12V) turns on, Power Board is normal.
the power voltage.
▶ When the NG LED turns on, the Power Board
▶ Fix the LCD MODEL switch to 20V.(Smart JIG)
can be judged as defective.
Copyright © 2018 LG Electronics. Inc. All rights reserved.
Only for training and service purposes.
`17Y OLED(W7) Power Board Diagnostic method
1 2
▶ Disconnect the Main Board 24Pin Power Cable connector. ▶ Connect the 24Pin Power Cable connector
to the Muitl Gender JIG 28Pin connector
3 4
▶ Switch the LCD MODEL S/W to 20V by checking ▶ When the OK LED(24V,12V) turns on, Power Board is normal.
the power voltage.
▶ When the NG LED turns on, the Power Board
▶ Fix the LCD MODEL switch to 20V.(Smart JIG)
can be judged as defective.
Copyright © 2018 LG Electronics. Inc. All rights reserved.
Only for training and service purposes.
`16Y/`17Y LED 18Pin Power Board Diagnostic method
1 2
3 4
▶ Connect the 18Pin Power Cable connector ▶ When the OK LED(24V,12V) turns on, Power Board is normal.
to the Muitl Gender JIG 24Pin connector ▶ When the NG LED turns on, the Power Board
can be judged as defective.
Copyright © 2018 LG Electronics. Inc. All rights reserved.
Only for training and service purposes.
`16Y LED(UH95/UH96) Power Board Diagnostic method
1 2
▶ Check power board voltage. ▶ Disconnect the Main Board 28Pin Power Cable connector.
▶ Fix the LCD MODEL switch to 24V.(Smart JIG)
3 4
▶ Connect the 28Pin Power Cable connector ▶ When the OK(24V,12V) LED turns on, Power Board is normal.
to the Muitl Gender JIG 28Pin connector ▶ When the NG LED turns on, the Power Board
can be judged as defective.
Copyright © 2018 LG Electronics. Inc. All rights reserved.
Only for training and service purposes.
`16Y/`17Y LED(UH85/UH93) Power Board Diagnostic method
1 2
▶ Check power board voltage. ▶ Disconnect the Main Board 28Pin Power Cable connector.
▶ Fix the LCD MODEL switch to 24V.(Smart JIG)
3 4
▶ Connect the 28Pin Power Cable connector ▶ When the OK LED(24V,12V) turns on, Power Board is normal.
to the Muitl Gender JIG 28Pin connector ▶ When the NG LED turns on, the Power Board
can be judged as defective.
Copyright © 2018 LG Electronics. Inc. All rights reserved.
Only for training and service purposes.
`16Y/`17Y LED 12Pin Power Board Diagnostic method
1 2
3 4
▶ Connect the 12Pin Power Cable connector ▶ When the OK LED(24V,12V) turns on, Power Board is normal.
to the Muitl Gender JIG 12Pin connector ▶ When the NG LED turns on, the Power Board
can be judged as defective.
Copyright © 2018 LG Electronics. Inc. All rights reserved.
Only for training and service purposes.
`16Y LED 12Pin Power Board Diagnostic method
1 2
3 4
▶ Connect the 12Pin Power Cable connector ▶ When the OK LED(24V,12V) turns on, Power Board is normal.
to the Muitl Gender JIG 24Pin connector ▶ When the NG LED turns on, the Power Board
can be judged as defective.
Copyright © 2018 LG Electronics. Inc. All rights reserved.
Only for training and service purposes.
`17Y LED 28Pin Power Board Diagnostic method
1 2
3 4
▶ Connect the 28Pin Power Cable connector ▶ When the OK LED(24V,12V) turns on, Power Board is normal.
to the Muitl Gender JIG 28Pin connector ▶ When the NG LED turns on, the Power Board
can be judged as defective.
Copyright © 2018 LG Electronics. Inc. All rights reserved.
Only for training and service purposes.