Professional Documents
Culture Documents
3 RH 714 PDF
3 RH 714 PDF
3.2.1. Using 1 1/4" MF rods ... .......................... . .......................... . .... . ....... . ................................................ 7
3.2.2. Using 1 1/4" extension rods ......................................................................................... .................. 7
3.2.3. Using 2" extension rods ....... .... ..... ...... ......................... ........ ..... ... .... .............................................. 7
4. MAIN COMPONENTS ..... . ... .. .. ... ................. ..... ........ . ..... ..................... ......... . ..... . .................. 8
6. HYDRAULICS . ............... ... . ...... .. .... . . . .. . ...... ................. . ... ........ ................................. .............. 12
6.1. Hydraulic components OX . . . .
...................................................................... ... ....... .......... ....... .............. . . 12
6.3. Operation OX . . . .
....................... .......................................... .............. ...... ............ ........................................ 14
7. MECHANICAL FUNCTIONS .............. ............................ . ........... . . . .. . ... .. ... ..... ......... . ....... . . . . . . . 18
7.1. Adjusting pito retainer .
....................................................... ................................................. . . ................ . 18
1. GENERALID:14665
These instructions describe the structure, operating principle and adjustments of the RH 714 rod
handler.
Sandvik Service is always ready to offer advice and help in all service problems.
RH 714
10: 15818
1. Rod
2. Handler
3. Rock drill serie
4. Rod length max 14'
a
00
00
ID: 25842
(*) The cassette can be used with 1 1/4", 1 1/2", 1 3/4" or 2" rods when the length of lifting cylinder
stroke is adjusted with adjusting screw (A).
The spare parts required by different rods are listed in the spare parts manual.
_____
_ �IO
10: 25843
1. Rod handler, upper end (The upper end rod handler has three alternative mounting positions.)
(1*)
2. Rod handler, lower end
• The rod handlers perform:
- rod transfers to drilling centre or to cassette, and
gripping of rod with jaws and rod storing into cassette.
3. Lower support
• The cylinder keeps the rods in a position where rod handling can take place.
8. Slide gate
• Prevents rods from rolling out and falling from the cassette.
9. Valve block
• The valves control the rod handler, Pito retainer,and movable suction head.
10. Flow divider valve
• The valve divides the oil flow so that both grippers (upper and lower end) move simultaneously
to drilling centre or to cassette.
ID: 25844
5. OPERATING PRINCIPLEIO:14675
When a rod is added,the gripper jaw (1) presses the slide gate (2) so that the rod can move over the
slide gate with the gripper to the drilling centre.
When the gripper is in the drilling centre, the rods in the cassette are retained behind the slide gate
(2) and under the surface (3),preventing the rods from falling out.
ID: 25845
When disassembling is started, the inclined edge (4) of the gripper body first presses the rods down
wards in the cassette,and then the slide gate under surface (3).
When a rod is taken from the drilling centre to the cassette, the gripper jaw and the rod together push
the slide gate (2) and the rods (5) in the cassette downwards,making room for the rod coming from
the drilling centre.
When the jaws open,the slide gate (2) closes,preventing the rods from escaping from the cassette.
ID: 25847
6. HYORAULICSID:14678
The rod handler is controlled using levers located in the cabin. They control the directional valves in
the rod handler valve block (200) with the purpose of directing the output oil from the variable dis
placement pump (50) to the cylinders. Rod handler valve block (200) is mounted to the side of the
feed.
The valve block (200) consists of eight on/off -type control valves (201-205,217,219,243). In addi
tion, the LS valve (206) is provided for pressurizing the pump (50). Valves (201), (202), and (203)
control rod handling functions. Control valve (201) directs oil flow to the gripper transfer cylinders,
moving the rod from cassette to drilling centre and from drilling centre to cassette. Control valve (202)
moves the jaw of the lower gripper (open/closed). Control valve (203) moves the jaw of the upper
gripper (open/closed). When the upper jaw is opened, valve 219 releases pressure from the lower
jaw cylinder into the receiver thus releasing the grip in the rod; the lower jaw continues to guide the
rod during threading. Control valve (204) moves the suction head (up/down),and control valve (205)
moves the Pito jaws (open/closed).
The double overcenter valve (199) at the Pito directional valve (205) has the purpose of preventing
damage to the Pito arms when threads are being loosened in Pito. All other cylinders controlled by
directional valves have their own pilot operated check valve (207) that ensures the remaining pressure
in the cylinder while the valve spool is in the middle position. The rod transfer cylinders (215, 216)
are provided with an additional flow distribution valve (208) whose purpose is to distribute an equal
oil flow to both cylinders in both directions.
When the rod string is being disassembled and a rod is taken to cassette,the coil Y217 of the control
valve (217) for the rod lifting cylinders (210) becomes activated and directs the return oil flow from
he cylinders into the tank. This decreases the force used for pushing a rod into the cassette. When
the rod is in the cassette and the control lever is released,the coil Y217 becomes dead and pressure
enters through the pressure regulator (263) to the piston head side of cylinders (210) and tightens
the rods in the cassette. The set value of the pressure regulator (263) is 30-40 bar.
The directional valve (243) is used for controlling the rod centralizer cylinders (option).
Oil flows from variable displacement pump (50) to port P2 of rod changer valve block (200). From
there,oil flows to the desired cylinders as directed by the control valves.
The coil Y206b of the LS valve (206) is activated whenever any coil of the directional valves (201-
205,217,219,243) in the valve block (200) is activated. The valve (206) is used for directing the LS
signal to the variable displacement pump (50) as long as any of the directional valve coils is activated.
The LS signal line also has a pressure relief valve (173) that restricts the maximum pressure of the
pump for cassette movements to 230 bar.
The rod handler is controlled using the levers on the control panel. They affect the directional valves
in the rod handler valve block (200) that have the purpose of directing the output of the gear pump
(80) to the cylinders. Rod handler valve block (200) is mounted to the side of the feed.
The valve block (200) consists of eight on/off -type control valves (201-205, 217,219, 243). Valves
(201),(202),and (203) control rod handling functions. Control valve (201) directs oil flow to the gripper
transfer cylinders,moving the rod from cassette to drilling centre and from drilling centre to cassette.
Control valve (202) moves the jaw of the lower gripper (open/closed). Control valve (203) moves the
jaw of the upper gripper (open/closed).When the upper jawis opened, valve 219 releases pressure
from the lower jaw cylinder into the receiver thus releasing the grip in the rod; the lower jaw continues
to guide the rod during threading. Control valve (204) moves the suction head (up/down),and control
valve (205) moves the Pito jaws (open/closed).
The double overcenter valve (199) at the Pito directional valve (205) has the purpose of preventing
damage to the Pito arms when threads are being loosened in Pito. All other cylinders controlled by
directional valves have their own pilot operated check valve (207) that ensures the remaining pressure
in the cylinder while the valve spool is in the middle position. The rod transfer cylinders (215, 216)
are provided with an additional flow distribution valve (208) whose purpose is to distribute an equal
oil flow to both cylinders in both directions.
When the rod string is being disassembled and a rod is taken to cassette, the coil Y330 of the control
valve (217) for the rod lifting cylinders (210) becomes activated and directs the return oil flow from
he cylinders into the tank. This decreases the force used for pushing a rod into the cassette.
When the rod is in the cassette and the control lever is released, the coil Y330 becomes dead and
pressure enters through the pressure regulator (263) to the piston head side of cylinders (210) and
tightens the rods in the cassette. The set value of the pressure regulator (263) is 30- 40 bar.
The directional valve (243) is used for controlling the rod centralizer cylinders (option).
From the gear pump (80) oil flows to the port P1 of the rod handler valve block (200) and,controlled
by the directional valves,continues to the desired cylinders.
The coil Y124 of the pressurizing valve (86) of the pump (80) is unactivated whenever any coil of the
directional valves (201-205,217,219, 243) in the valve block is activated. The valve (86) is used for
directing the output of the pump (80) against the plug (A1),whereby oil flow either to an actuator of
the cassette or,if the actuator is at its extreme position, through the pressure limit valve (85) to the
tank.
7. MECHANICAL FUNCTIONSID:14685
• Loosen the bolts between the feed and the Pito retainer.
• Mount a shank to the rock drill and an extension sleeve to the Pito retainer jaws.
• Drive the shank into the sleeve by using the rock drill.
• Tighten the bolts, and run the rock drill to the upper position.
,-;;; 't'L'=�________ _
"----------- �ot
ID 25861
• Move a rod with the gripper transfer cylinders between the extension sleeve and the rock drill shank.
• Loosen the bolts (1) between the rod handlers and the feed.
• Loosen the locking nuts of the adjusting screws (2,3, 4).
• Centralize the rod to the drilling centre using the adjusting screws (2,3). Lock the adjustment.
• Move the rod back to the cassette, and adjust the screw (4) so that the rod is far enough in the
cassette (behind the slide gate) and that the gripper jaw pushes the rod against the inclined surface
of the gripper. Lock the adjustments.
• Test all the movements.
Each shift:
- Check all possible oil leaks.
- Tighten all loosened nuts and screws.
- Lubricate the sliding body (4) grease nipples (2 pcs).
Once a week:
- Wash the rod handler.
- Lubricate all grease nipples.
- Check the condition of the gripper and Pito jaws.
00
ID 25909