Professional Documents
Culture Documents
4.6 Domino Poster (2006.10)
4.6 Domino Poster (2006.10)
• Spray all sides of the formwork before every use with PERI
BIO Clean.
DOMINO
Fastens, aligns and tightens in a
single operation
The lightweight panel formwork countries where our products are used.
DM 75
wall thicknesses from 150 to 350 in Inside formwork: DGE articulated corner 5.
D 50
200 300
DAR compensation
2. Infills
DM 75
waler 2 DWD 5
DM 75
5
*
DM 7
75
10 mm timber
D 50
2 DWD 5
240 350
DAR compensation
waler 115 mm timber
1. Panel couplers
2 DWD 5
+ 115 mm timber
250 365
Information:
When using the articulated corner as a 90° inside corner,
the ties may be inserted through the outer holes of the
articulated corner.
Only when compensation walings are used e.g. oblique
angles, may the ties be placed through the inner holes
of the articulated corner. Two DRS alignment couplers
Item no.: 066080
on 2.50 m element heights
DAR compensation
115 mm timber
DWD 5 waler
DWD 5
D 50
7. Stop Ends 6. 2.
With DOMINO Stopend Panel MT/MTF With conventional stopend formwork D 50
View A
DM 75 DM DM
75 75
c
max. 365mm
DM DM
75 75 Achieved by offsetting the 250 100 75 50 25 DAW DGE DGE
id ht
h
th
DM 75
275
0 - 170
c
DM 75
timber by site
Push-Pull Props and Kicker Braces Foundations Wall offset from 250 to 350 mm
With articulated corner and filler
Push-pull props and kickers to brace panels according to the table. They are timber up to 100 mm
Strip and individual foundations with When using the tie bracket for the top Outside Corner
the formwork and bearing the windload connected to the panel with the foundation tie clamp and tie bracket tie position, the DOMINO elements do Angle DAW
D 50
are to be arranged as shown on the DOMINO Compensation waler and to not have to be aligned exactly opposite
adjacent diagram and table. the slab with the appropriate base plate The DOMINO foundation tie clamp each other. Anchoring can take place at
The first panel must always be braced and the anchor bolt PERI MMS 20x130. replaces the bottom tie position, saves any position on the panel.
max. 350
min. 250
with 2 push-pull props and subsequent working space and hence earthwork.
Ties are tensioned accurately with a self-
325
350
x = Distance of base plate [m] 1.2 1.6 2.0 2.4 2.9 3.5 D 50
from rear face of formwork
the foot of the push-pull-prop for the given width of influence. DAR compensation waler DSA stopend tie
DM 75
2
Wind loads: h < 8 m = 0.5 kN/m DAR compensation waler
8 m < h < 20 m = 0.8 kN/m2
100 75 50 25 DM 75 DGE DAW DWD 5 DPA For easy connection of push-pull props The bracket for an 850 mm wide For moving vertical elements or
id ht
h
corner corner angle compens. plate support and kickers to horizontal and vertical concreting scaffold interconnected panels forming a unit.
Large units can be shifted with
struts of the DOMINO panels. The maximum bearing capacity is 500 kg the DOMINO lifting hook.
with a max. 30°crane sling angle.
Always use 2 hooks for moving
operations!
Follow instructions
for use!
steel
250
DOMINO Versetzhaken
Art.-Nr. 066091
Betriebsanleitung
425
m2 2.50 1.88 1.88 Planking and rear safety handrail Stacking Device DOMINO, galv.
450
A guardrail is mandatory
> 2,00m
Edition 10/2006
DOMINO
Panel Formwork
Poster
product range 4.60 e 10/2006 5ma Art.-Nr.: 790427 © Copyright by PERI GmbH
PERI GmbH
P.O. Box 12 64
89259 Weissenhorn
Tel.: 0 73 09 / 950 -0
Fax: 0 73 09 / 951 -0
info@peri.de
Edition 10/2006 www.peri.de
D