Professional Documents
Culture Documents
Patient Gas Module
Patient Gas Module
Patient Gas Module
'UlJHU0HGLFDO$* &R.*D$3ULPXV
5HSDLU,QVWUXFWLRQV *HQHUDOLQWURGXFWLRQ
*HQHUDOLQWURGXFWLRQ
7HVWLQJZLWKVHUYLFHPRGH
7HVWLQJZLWKRXWVHUYLFHPRGH
All rights reserved. Copyright reserved • R5132300T12_PGM.fm 05.04.02 • Repair Instructions • Version 1.0 • Released
&RQQHFWLRQGLDJUDPWXELQJGLDJUDP
'UlJHU0HGLFDO$* &R.*D$3ULPXV
5HSDLU,QVWUXFWLRQV *HQHUDOLQWURGXFWLRQ
1. Remove the two PGM module fixing screws (see Fig. 1. Remove the three fixing screws (see Fig. 5).
4).
All rights reserved. Copyright reserved • R5132300T12_PGM.fm 05.04.02 • Repair Instructions • Version 1.0 • Released
2. Remove the four side panel fixing screws (see Fig. 6).
)LJ PGM module fixing screws
'UlJHU0HGLFDO$* &R.*D$3ULPXV
5HSDLU,QVWUXFWLRQV *HQHUDOLQWURGXFWLRQ
3. Tilt the side panel slightly (Fig. 7/1) and open up the top
cover.
)LWWLQJWKH3*0KRXVLQJ
'UlJHU0HGLFDO$* &R.*D$3ULPXV
5HSDLU,QVWUXFWLRQV *HQHUDOLQWURGXFWLRQ
5HPRYLQJWKH,/&$
'UlJHU0HGLFDO$* &R.*D$3ULPXV
5HSDLU,QVWUXFWLRQV *HQHUDOLQWURGXFWLRQ
All rights reserved. Copyright reserved • R5132300T12_PGM.fm 05.04.02 • Repair Instructions • Version 1.0 • Released
5. Disconnect the tube fitting from the pump (see Fig. 11).
'UlJHU0HGLFDO$* &R.*D$3ULPXV
5HSDLU,QVWUXFWLRQV *HQHUDOLQWURGXFWLRQ
All rights reserved. Copyright reserved • R5132300T12_PGM.fm 05.04.02 • Repair Instructions • Version 1.0 • Released
'UlJHU0HGLFDO$* &R.*D$3ULPXV
5HSDLU,QVWUXFWLRQV *HQHUDOLQWURGXFWLRQ
5HPRYLQJWKH,5,$
)LWWLQJWKH,/&$
'UlJHU0HGLFDO$* &R.*D$3ULPXV
5HSDLU,QVWUXFWLRQV *HQHUDOLQWURGXFWLRQ
)LWWLQJWKH,5,$
'UlJHU0HGLFDO$* &R.*D$3ULPXV
5HSDLU,QVWUXFWLRQV *HQHUDOLQWURGXFWLRQ
All rights reserved. Copyright reserved • R5132300T12_PGM.fm 05.04.02 • Repair Instructions • Version 1.0 • Released
5HPRYLQJWKHIDQ
)LJ Fan fixing screws 4. Plug the electrical connector of the new fan into the
ILCA (see section 1.4 Connection diagram/tubing
diagram).
3. Fit the new fan in keeping with the direction of flow (see
Fig. 20). 5. Fit the PGM housing (see section 1.5.2 Fitting the PGM
housing).
1. Remove the PGM module (see section 1.5 Removing 1. Fit the tube connections one after the other (see
the PGM module). section 1.4 Connection diagram/tubing diagram).
2. Remove the IRIA (see section 1.7 Removing the IRIA). 2. Plug in the electrical connection between the ILCA and
All rights reserved. Copyright reserved • R5132300T12_PGM.fm 05.04.02 • Repair Instructions • Version 1.0 • Released
3. Take the cover plate out of the housing (see Fig. 21). the O2 sensor housing (see Fig. 13 or section 1.4
Connection diagram/tubing diagram).
3. Lay the tube to the pump, to the T-piece of S2 and the
O2 sensor cable underneath the IRIA (see Fig. 18).
4. Screw in the four IRIA fixing screws (see Fig. 14 ).
5. Plug in the electrical connector to the IRIA (see Fig.
12).
6. Fit the PGM housing (see section 1.5.2 Fitting the PGM
housing).