Professional Documents
Culture Documents
Sincronizacion de Motor Toyota 2tr-Fe PDF
Sincronizacion de Motor Toyota 2tr-Fe PDF
REPLACEMENT
1. REMOVE ENGINE ASSEMBLY (SEE PAGE 14–19)
2. REMOVE DRIVE PLATE & RING GEAR SUB–ASSY (AUTOMATIC TRANSMISSION)
(SEE PAGE 14–19)
SST 09213–54015 (91651–60855), 09330–00021
3. REMOVE CLUTCH COVER ASSY (MANUAL TRANSMISSION) (SEE PAGE 42–5)
4. REMOVE CLUTCH DISC ASSY (MANUAL TRANSMISSION) (SEE PAGE 42–5)
5. REMOVE FLYWHEEL SUB–ASSY (MANUAL TRANSMISSION) (SEE PAGE 14–19)
SST 09213–54015 (91651–60855), 09330–00021
6. REMOVE REAR END PLATE (SEE PAGE 14–19)
7. REMOVE ENGINE WIRE
8. INSTALL ENGINE STAND
9. REMOVE FLUID COUPLING ASSY
(a) Remove the 4 nuts with the coupling from the water pump pulley.
10. REMOVE FAN PULLEY
G35174
SST SST (b) Insert the blade of SST between the pans. Cut through
the applied sealer and remove the oil pan.
SST 09032–00100
NOTICE:
Be careful not to damage the contact surfaces of the oil
pans.
A99215
A86858
(b) Remove the oil pan by prying between the oil pan and cyl-
inder block with a screwdriver.
HINT:
Tape the screwdriver tip before use.
NOTICE:
Be careful not to damage the contact surfaces of the cylin-
der block and oil pan.
(c) Remove the O–ring.
A86859
A99635
G35081
14–46
ENGINE MECHANICAL – CHAIN (2TR–FE)
A99203
G35202
Groove
A97861
14–47
ENGINE MECHANICAL – CHAIN (2TR–FE)
SST
Loosen
G37559
SST
G35121
G37278
G37295
G37296
G37545
A53897
14–49
ENGINE MECHANICAL – CHAIN (2TR–FE)
(b) Using SST and crankshaft pulley bolt, remove the crank-
shaft timing gear and chain.
SST SST 09950–40011 (09951–04010, 09952–04010,
09953–04020, 09954–04010, 09955–04061)
A68735
(f) Check that each timing mark is matched with the corre-
Large Timing Mark Mark Link
sponding mark link.
Mark Link Timing Mark
Mark Link
Timing Mark
P15100
14–50
ENGINE MECHANICAL – CHAIN (2TR–FE)
Pin
A68751
G37296
G37295
Timing Mark
(b) Use a rope to tie the chain of the crankshaft timing sprock-
et. Tie the rope near the gear.
NOTICE:
After the chain tensioner has been installed, the rope must
be removed.
HINT:
The rope is tied so that the chain will not jump a tooth.
G37547
G37279
14–52
ENGINE MECHANICAL – CHAIN (2TR–FE)
G37278
A99635
G37340
14–54
ENGINE MECHANICAL – CHAIN (2TR–FE)
Nut (b) Temporarily install the oil pan with the 16 bolts and 2 nuts.
10 HINT:
11 12 13 14 15 Bolt length:
16 20 mm (0.79 in.) for bolt A
40 mm (1.57 in.) for bolt B
17 (c) Uniformly tighten the 16 bolts and 2 nuts in the sequence
19 18 shown in the illustration.
21 Torque: 26 N⋅m (265 kgf⋅cm, 19 ft⋅lbf)
22 20
G38130
G37317 G38131
16 17 (b) Temporarily install the oil pan with the 18 bolts and 2 nuts.
12 13 14 15
11 (c) Uniformly tighten the 18 bolts and 2 nuts in the sequence
18
shown in the illustration.
10
2 19 Torque: 9.0 N⋅m (92 kgf⋅cm, 80 in.⋅lbf)
3 20
9
1
21
4
8
7 5 24 23 22
6 G35174
14–55
ENGINE MECHANICAL – CHAIN (2TR–FE)
17 18 19 20 (d) Temporarily install the head cover with the 19 bolts and 2
21
nuts.
2 3 6 7 (e) Uniformly tighten the 19 bolts and 2 nuts in the sequence
16 shown in the illustration.
9
Torque: 9.0 N⋅m (92 kgf⋅cm, 80 in.⋅lbf)
(f) After tightening the 19 bolts and 2 nuts at the specified
1 4 5 8 torque, retighten 1–8 bolts at the torque.
13 12 11 10
15 14 G35202