Professional Documents
Culture Documents
Manitou MRT - 1432
Manitou MRT - 1432
For Parts Orders contact your Manitou North America Dealer or call:
Manitou North America, Parts Dept. 800--425--3727 or (254) 799--0232
Parts Dept. Fax: (254) 867--6504 Website: www.manitou--na.com
MRT1432
400°
M SERIES E- 2
3B6 SERIES INSTRUMENTS
S/N: 411048 AND BELOW
OPERATOR/SERVICE
MANUAL
THIS OPERATOR’S MANUAL MUST BE KEPT IN THE LIFT TRUCK. IT MUST BE READ AND
UNDERSTOOD BY OPERATORS.
CATALOG 648226AS
R/11-10
R03-04
II
III
IV
The handling of suspended loads by means of a truss boom or other similar device can introduce dynamic
forces affecting the stability of the machine that are not considered in the stability criteria of industry test
standards. Grades and sudden starts, stops and turns can cause the load to swing and create a hazard.
1. DO NOT exceed the rated capacity of the telescopic handler as equipped for handling suspended
loads. The weight of the rigging must be included as part of the load.
2. During transport, DO NOT raise the load more than 12 inches (305 mm) above the ground, or raise
the boom more than 45 degrees.
4. Use multiple pickup points on the load when possible. Use taglines to restrain the load from swinging
and rotating.
5. Start, travel, turn and stop SLOWLY to prevent the load from swinging. DO NOT exceed walking
speed.
6. Inspect rigging before use. Rigging must be in good condition and in the U.S. comply with OSHA
regulation §1910.184, “Slings,” or §1926.251, “Rigging equipment for material handling.”
7. Rigging equipment attached to the forks must be secured such that it cannot move either sideways or
fore and aft. The load center must not exceed 24 inches (610 mm).
8. DO NOT lift the load with anyone on the load, rigging or lift equipment, and NEVER lift the load over
personnel.
9. Beware of the wind, which can cause suspended loads to swing, even with taglines.
WARNING
U.S. OSHA regulations effective November 8, 2010 (29 CFR Part 1926, Subpart CC - Cranes and Derricks in
Construction) include requirements for employers that use powered industrial trucks ("forklifts") configured
to hoist (by means of a winch or hook) and move suspended loads horizontally. In particular, this regulation
applies to any rough-terrain forklift (e.g., "telescopic handler") equipped with a jib or truss boom with a
hook (with or without a winch), or a hook assembly attached to the forks. [Note: This regulation is in
addition to the OSHA regulation that requires specific forklift operator training: §1910.178(l).]
When a forklift / telescopic handler is configured and used for hoisting, the employer must ensure that:
1. Forklift, lift equipment and rigging have been inspected (each shift, month and year) and are in
good, safe condition and properly installed.
3. Work zone ground conditions can support the equipment and load. Any hazardous conditions in the
work area have been identified, and the operator notified.
4. Equipment is being used within its rated capacity and in accordance with the manufacturer's
instructions.
VI
6. During use, no part of the equipment, load line or load will be within the minimum clearance
distance specified by OSHA [10 feet (3.0 m), and more for lines rated over 50 kV] of any energized
power line, and any taglines used are non-conductive.
7. In addition, for lift equipment with a rated capacity greater than 2000 lbs. (907 kg), the employer
must ensure that:
b.) Monthly and annual inspections are performed and documented, and records retained (three
months for monthly, one year for annual);
c.) Before November 10, 2014, operators must have had the additional training and qualification /
certification required by OSHA regulations §1926.1427 and §1926.1430.
Note: Refer to the full text of the OSHA crane regulation (29 CFR Part 1926, Subpart CC) for a detailed
description
VII
CONCLUSION:
TECHNICAL SUPPORT
All data provided in this manual is subject to production changes, addition of new models, and improved prod-
uct designs. If a question arises regarding your forklift, please consult your dealer or K-D Manitou, Inc. for the
latest information. When ordering service parts or requesting technical information, be prepared to quote the
applicable Model/Serial Numbers.
VIII
NOTE or NOTICE
Provides information, special instructions or references about the lift truck.
IMPORTANT
Precautions which must be taken to avoid damage to the lift truck.
CAUTION
Indicates a potentially hazardous situation which, if not avoided, may result in minor or
moderate injury. May also alert unsafe practices.
WARNING
Indicates a potentially hazardous situation which, if not avoided, may result in death or
serious injury!
DANGER
Indicates an imminently hazardous situation which, if not avoided, will result in death or
serious injury.
Diesel Engine Exhaust and some of its constituents are known to the State of California
to cause cancer, birth defects or other reproductive harm.
WARNING: Battery posts, terminals and related accesories and related accessories
contain lead and lead compounds. Wash hands after handling.
IX
The purpose of this chapter is to introduce you to the safety messages, decals, and nameplates found on
your forklift truck. The decals are identified by name, part number, location, and a brief description. (The
forklift model logos, and other misc. decals not shown, can be found in your forklift parts manual.) The
decals illustrated may not be exactly the same as those installed on your forklift; installation of the decals
varies depending on the forklift model, series, decal updates, etc.. The size and location of some decals
limit the amount of information that can be placed upon it. For this reason, additional detailed information
not found on the decals is provided through-out this manual.
Every decal placed on the lift truck is important; they are constant reminders of safety and instructions that
should never be taken for granted. Even experienced operators can be seriously injured or killed by ignor-
ing, refusing to enforce, or forgetting to follow safe operating procedures! Do not assume you know all safe-
ty issues concerning the decals. Before operating the lift truck; learn the meaning(s) of the decals as
described in this manual. If any decal becomes illegible or missing, have it replaced immediately! Always
replace decals using the same decal part no., unless otherwise specified by the manufacturer. For replace-
ment decals not found in your parts manual, contact your nearest dealer. If you have any questions, contact
your supervisor or nearest dealer for advice before operating your forklift!
801011
The backup alarm must sound when the forklift is placed in reverse gear.
No Riders - 420732
Location: on the cab entrance(s), and on or near wheel fenders and engine
cover.
XI
Keep hands and clothing away from rotating fan and belts.
XII
221322
234800
XIII
Anti-Freeze - 234799
Location: on the radiator, near the radiator filler cap.
No Step - 496735
Location: varies, depending on the forklift model.
XIV
Instructs personnel not to travel beneath or upon the lift truck forks.
XV
Important manufacturer information about the attachment. Record this information for use
when contacting the maufacturer for parts and service.
496550 496538
Forklift Data Plate - 496550
(Boom equipped models)
Forklift Data Plate - 496538
(Mast equipped models)
Location: within the operator’s compartment.
XVI
M RT 1 4 3 5
M Series
Turbo
M RT 1 6 3 5
M Series
Turbo
3
Downloaded from www.Manualslib.com manuals search engine
MRT 1432 - 1635 MSeries
IT EN DE
1 DATA DI PUBBLICAZIONE
a
1 DATE PUBLICATION
st
1 DATUM AUSGABE
st
Date publication:
Data di pubblicazione: Datum ausgarbe:
Text and illustrations herewith enclosed Die Reproduktion, auch nur teilweise, die-
E’ vietata la riproduzione, anche parziale, ses Textes und der Abbidungen ist verboten.
del testo e delle illustrazioni. may not be reproduced, not even in part
and by any means.
Because of the possible time lag beween Aus Gründen der Korrektheit muß darauf
La differenza tra i tempi di aggiornamento hingewiesen werden, daS der
in stampa e i tempi delle modifiche tecni- the introduction of technical modifications
(an on-going process the aim of which Zeitunterschied zwischen in Druck
che (variando quast’ultime befindlicher Naufassung und technischen
continuamente, ciò al fine di offrire prodot- is to offer products which are being
continually improved) and the latest up Veränderungen (die für ein Angebot von
ti sempre più qualificati) impongono di immer basseren Geräten kontinuierlich
dichiarare, per correttezza, che i dati date of the manual, we must point out,
for the sake of correctness, that the data sind) zu Unterscheden in den Angaben
contenuti nella presente edizione sono dieser Auflage Fühuren kann und daß die
suscettibili di variazione in qualsiasi contained in this edition is liable to chan-
ge at any time and are therefore not darin enthaltenen Angaben underbindlinch
momento e che quindi non sono sind und jederzeit verändert werden kön-
impegnativi. binding.
nen.
4
Downloaded from www.Manualslib.com manuals search engine
MRT 1432 - 1635 MSeries
IT EN DE
- Ricambi e attrezzature originali. - Original replacement parts and - Ersatzteile und originalausstattung.
- Istruzioni d’uso per il carrellista. attachments. - Gebrauchsanweisung für den
- Avvertenze. - Driver’s operating instructions. fahrer.
- Istruzioni generali. - Warning - Warnung.
- Istruzioni di guida. - General instructions. - Allgemeine anweisungen.
- Istruzioni di movimentazione. - Operating instructions. - Fahranweisungen.
- Movimentazione di un carico. - Handling instructions. - Handhabungsanweisungen.
- Istruzioni di manutenzione del - Load handling. - Handhabung einer last.
carrello elevatore. - Maintenance instructions of the lift - Wartungsanweisungen des
- Prima della messa in marcia del truck. gebelstaplers.
carrello elevatore nuovo. - Before starting up a new lift truck. - Vor der inbetriebnahme eines neuen
gabelstaplers.
5
Downloaded from www.Manualslib.com manuals search engine
MRT 1432 - 1635 MSeries
IT EN DE
5 - A C C E S S O R I A D AT TA B I L I 5 - A D A P TA B L E AT TA C H - 5 - A L S S O N D E R A U S S TAT-
IN OPZIONE SULLA MENTS IN OPTION ON - T U N G A N Z U PA S S E N
GAMMA THE RANGE DES ZUBEHÖR
6
Downloaded from www.Manualslib.com manuals search engine
MRT 1432 - 1635 MSeries
IT EN DE
Sul motore termico (FIG.B) On internal combustion engine(FIG.B) Auf dem dieselmotor (ABB. B)
7
Downloaded from www.Manualslib.com manuals search engine
MRT 1432 - 1635 MSeries
IT EN DE
Sulla trasmissione idrostatica (FIG.C) On hydrostatic drive (FIG.C) Auf dem hydrostatishen antrieb
(ABB. C)
Sull’assale anteriore e posteriore On front and rear axle (FIG.D) Auf der vorder- und hinterache
(FIG.D) (ABB. D)
1 - Tipo e modello dell’assale 1 - Axle type and model 1 - Typ und Modell der Achse
2 - Numero di serie 2 - Serial N° 2 - Serien-Nr.
Per poter indicare più facilmente tutti Um diese Angaben stets bei der Hand
Write all these numbers in the empty zu haben, ist es ratsam, die Nummern
questi numeri, consigliamo di riportarli
subito negli spazi vuoti che precedono. spaces. Since the MANITOU policy is to Ihres Geräts in den freien Feldern einzu-
Poiché la politica MANITOU è di tendere constantly improve our products, our tragen. Da die MANITOU-Politik nach
ad un miglioramento costante dei nostri range of telescopic lift trucks may be der ständiger Verbesserung unserer
prodotti, la nostra gamma di carrelli ele- subject to modifications without our Produkte strebt, kann die Lieferpalette
vatori telescopici può essere soggetta being obliged to give advance warning unserer Teleskoplader einigen Änderun-
ad alcune modifiche senza che sussista to our customers. gen ausgesetzt werden, deren
l’obbligo per noi di dar avviso alla nostra Bekanntgabe an die Kundschaft nicht
clientela. verpflichtend ist.
FIG.B 4 FIG.C
1 2
FIG.D FIG.E
8
Downloaded from www.Manualslib.com manuals search engine
Downloaded from www.Manualslib.com manuals search engine
Downloaded from www.Manualslib.com manuals search engine
1- ISTRUZIONI
INSTRUCTIONS
ANWEISUNGEN
La manutenzione dei nostri carrelli All maintenance on our lift trucks Zur Instandhaltung unsere
elevatori deve tassativamente esse- must be carried out using original Teleskoplader müssen
re realizzata con pezzi originali. parts. Originalersatzteile verwendet wer-
den
Autorizzando l’utilizzo di pezzi non By allowing non-original parts to be
originali, rischiate: used, you run the risk: Die Verwendung nicht orginaler
Ersatzteile beinhaltet gewisse
- Giuridicamente di coinvolgere la - Legally, of being liable in the event of Risiken
vostra responsabilità in caso an accident.
d’incidente. - Technically, of causing breakdowns to - Im Falle eines Unfalls die rechtlichen
- Tecnicamente di causare problemi di occur or of reducing your lift truck's Konsequenzen zu tragen
funzionamento alla longevità del service life. - Technische Betriebsstörungen
carrello elevatore. hervorzurufen oder die Lebensdauer
des Gabelstaplers zu verringern.
L’utilizzo - da parte dell’utente - di pezzi Using counterfeit parts or components Die verwendung nicht orginaler
contraffatti o di componenti non omolo- not approved by the manufacturer may Ersatzteile Teilen oder vom Hersteller
gati può mettere un termine alle condi- put an end to contract warranty terms nicht zugelassenen Komponenten führt
zioni di garanzia contrattuale e indurre il and lead the maker to withdraw the lift zum Erlöschen der vertraglichen
costruttore al ritiro del Certificato di truck's certificate of compliance. Garantie führen und zwingd den
Conformità. Hersteller zum Rückzug der
Konformitätserklärung zwingen.
Utilizzando i pezzi originali durante By using original parts during
le operazioni di manutenzione, vi maintenance operations, you are Durch den einsatz von originaltei-
proteggete giuridicamente. legally covering yourself. lenbei Instandhaltungsarbeiten,
schützen sie sich rechtlich.
- L’utente che si rifornisce altrove, lo fa a - Any user who procures parts from
suo rischio e pericolo. another quarter does so at his own - Der Benutzer, der seine Ersatzteile
- L’utente che modifica o fa modificare risk. anderswo bezieht, tut dies auf eigene
da terzi il carrello elevatore, deve - Any user who modifies his lift truck or Gefahr
essere consapevole che un nuovo has it modified by a service company, - Der Benutzer, der seinen
materiale è messo sul mercato, il che must consider that a new item of Teleskoplader verändert oder durch
coinvolge la sua responsabilità. equipment has been brought onto the einen Dienstleistungsbetrieb verändern
- L’utente che copia o fa copiare i pezzi market and therefore takes liability for läßt, muß davon ausgehen, daß ein
d’origine, si espone a rischi giuridici. it. neues Produkt auf den Markt kommt
- Il Certificato di Conformità implica la - Any user who copies original parts or und wird somit haftpflichtig.
responsabilità del fabbricante solo per i has them copied is taking a risk from - Der Benutzer, der Originalteile kopiert
pezzi scelti o elaborati sotto il suo con- the legal viewpoint. oder kopieren läßt, setzt sich rechtli-
trollo. - The certificate of compliance only chen Gefahren aus.
- Le condizioni pratiche di manutenzione binds - Die Konformitätserklärung bindet den
sono fissate dal fabbricante. Se l’uten- the maker for parts chosen or Hersteller nur für die von ihm gewähl-
te non le rispetta, la responsabilità del produced ten oder unter seiner Aufsicht agefer-
fabbricante non è coinvolta. under the maker's control. tigten Ersatzteile Teile.
- The practicalities of maintenance terms - Die praktischen Wartungsbedingungen
werden vom Hersteller definiert. Sollte
are set out by the maker. The maker is der Benutzer diese nicht einhalten,
in no way liable in the event of the übernimmt der Hersteller keine
user not Haftung.
complying with such terms.
Il fabbricante apporta all’utente: The manufacturer brings to the Der Hersteller bietet dem Benutzer:
user:
- Il savoir-faire e la sua competenza. - His know-how and skill. - Sein Know-how und seine Kompetenz.
- La garanzia della qualità dei lavori - Guaranteed quality work. - Eine Qualitätsgarantie der
realizzati. - Original replacement parts. durchgeführten Arbeiten.
- I pezzi di ricambio originali. - Help with preventive maintenance. - Original Ersatzteile.
- Un’assistenza alla manutenzione - Effective help with diagnosing faults. - Hilfestellungen zur vorbeugenden
preventiva. Wartung.
- Un’efficace assistenza alla diagnosi. - Eine wirkungsvolle Diagnosehilfe.
- I miglioramenti dovuti allo scambio di - Enhancements gained from feedback. - Ständige Weiterentwicklung der
esperienze. - Training for operating staff. Produkte.
- La formazione del personale - Only the manufacturer knows the - Eine Ausbildung des
incaricato. details of the lift truck design and the Betriebspersonals.
- Solo il fabbricante conosce refore has the best technological capa - Nur der Hersteller kennt die
dettagliatamente la progettazione del bility to carry out maintenance. Konstruktion
carrello e quindi le migliori capacità des Teleskopladers im Detail und
tecnologiche per assicurarne la verfügt somit über die besten techni
manutenzione. schen Fähigkeiten, um dessen
Wartung zu gewährleisten.
I pezzi di ricambio d’origine sono Original replacement parts are Originalersatzteile werden aussch-
distribuiti esclusivamente da distributed exclusively ließlich von MANITOU und dem
MANITOU by MANITOU and its dealer netz seiner Vertragshändler
e dalla rete dei concessionari. network. vertrieben.
La lista della rete dei concessionari può You can obtain the list of dealers by Ein Anruf bei unserer Ersatzteilabteilung
esservi fornita telefonando al servizio phoning the spare parts department on : genügt und Sie erhalten die Liste der
dei pezzi di ricambio : TEL : 0033240091011 Vertragshändler :
TEL : 059950518 TEL : 0033240091011
Caution Warnung
Avvertenza
Whenever you see this symbol it Dieses Symbol bedeutet:
Ricordate che questo simbolo means :
significa:
Attenzione! Prudenza! Sono in Warning! Be careful! Your safety or Achtung! Seien Sie vorsichtig! Ihre
gioco la vostra sicurezza e quella the safety of the lift truck is at risk. Sicherheit, die Sicherheit Dritter
del carrello elevatore. oder die des Teleskopladers sind in
Gefahr.
- La maggior parte degli incidenti legati - Most accidents connected with the
all’utilizzo, alla manutenzione e alla use, maintenance and repair of the lift - Die meisten Unfälle beim Gebrauch,
riparazione del carrello elevatore, sono truck are due to non application of the bei der Wartung und bei der Reparatur
dovuti alla non-applicazione e all’inos- basic safety instructions. By being des Gabelstaplers sind auf die
servanza delle più elementari norme di aware of the risks to which you are Nichtanwendung und Nichteinhaltung
sicurezza. Individuando i rischi ai quali exposed and by taking the necessary der grundlegenden
vi esponete e prendendo tutte le preventive measures, you should be Sicherheitsanweisungen zurückzufüh-
necessarie precauzioni, potrete evitare able to avoid accidents occurring. ren. Wenn Sie diese Gefahren erken-
questi incidenti. - Any operation or manoeuvre not nen, und die nötigen vorbeugenden
- Tutte le operazioni o manovre non described in the instructions is prohibi- Maßnahmen treffen, können Sie diese
descritte nel manuale d’istruzioni devo- ted, however, any person who does Unfälle vermeiden.
no essere evitate, e in ogni caso colui use another method must first ensure - Jegliche Anwendung, jedes Manöver,
che utilizza un altro metodo deve that he is not putting himself, another welches in den Bedienungsanleitung
prima assicurarsi che sia garantita la person or the lift truck in danger. nicht beschrieben sind, sind von vorn
propria incolumità, quella degli altri e il - The manufacturer is not able to antici- zu unterlassen.
buono stato del carrello elevatore. pate all possible risk situations. - Der Hersteller haftet auf keinen Fall für
- Pertanto, non potendo prevedere tutte Therefore the safety instructions and alle Gefahrensituationen. Die
le situazioni di pericolo, le istruzioni e notices given in the user manual and Anweisungen und
norme di sicurezza relative al carrello on the lift truck are not exhaustive. Sicherheitsvorschriften in diesem
elevatore, date dal costruttore e ripor- Handbuch und auf dem Teleskoplader
tate nel presente manuale, non sono selbst erheben daher keinen Anspruch
da considerarsi esaustive. auf Vollständigkeit.
L’inosservanza delle norme di sicurezza Any bending of the rules in safety noti- Alle Verstöße gegen die
o delle istruzioni d’uso, di manutenzione ces or the user, maintenance or repair Sicherheitsvorschriften, Bedienungs-,
o di riparazione del carrello elevatore instructions for your lift truck may result Wartungs- oder Reparaturanweisungen
possono essere all’origine di gravi infor- in serious, or even fatal, accidents. Ihres Gabelstaplers können schwere, ja
tuni, anche mortali. sogar tödliche Unfälle verursachen.
Richiamiamo l’attenzione degli utilizzato- We would remind users of the risks in Beachten Sie die Gefahren, welche
ri sui rischi a cui vanno incontro, andan- driving at excessive speed with regard durch nicht angepasste
do ad una velocità eccessiva rispetto to traffic conditions, particularly : Geschwindigkeit, den
alle condizioni di circolazione, in Verkehrsbedingungen,
particolare: Witterungsbedingungen und
Fahrbahnbeschaffenheit entstehen:
- Rischio di perdere il controllo su stra - Risk of loss of control on a poor-qua -Es besteht die Gefahr, in Abhängigkeit
da dissestata. lity track. von Geschwindigkeit, Witterung und
- Aumento dello spazio di frenata. - Increased stopping distance. Fahrbahnbeschaffenheit die Kontrolle
uber das Fahrzeug zu verlieren
-Der Bremsweg kann sich erheblich
verlängern.
L'utilizzatore deve sempre poter control- The user must remain in full control of Der Benutzer muß das Fahrzeug stän-
lare il carrello elevatore e his lift truck and should : dig unter Kontrolle haben :
quindi deve :
- Adattare la velocità ad ogni situazione - Adapt his speed to each situation in - Die Geschwindigkeit der Situation
per preservare la propria incolumità, order to be maintain his own safety, anpassen, um die eigene Sicherheit,
quella altrui e quella della propria that of others and of his equipment. die Sicherheit Dritter und die des
macchina. - Always be aware of his stopping Teleskopladers zu bewahren.
- Valutare continuamente lo spazio di distance. - Den Bremsweg ständig einschätzen
frenata. können.
L’esperienza ci insegna che si possono On the basis of experience, there are a Erfahrungsgemäß können bestimmte
avere alcune controindicazioni sull’im- number of possible situations in which Gegenanzeigen für den Einsatz des
piego del carrello elevatore. Questi operating the lift truck is contra-indica- Gabelstaplers auftreten. Diese vorherseh-
impieghi anomali prevedibili, di cui i prin- ted. Such foreseeable abnormal uses, baren, unnormalen Einsätze, von denen
cipali sono elencati qui di seguito, sono the main ones being listed below, are die hauptsächlichen nachstehend genannt
formalmente vietati. strictly forbidden. werden, sind strengstens untersagt.
Il responsabile dello stabilimento deve The person in charge of the equipment Der verantwortliche Mitarbeiter muß
tenere conto di questi criteri per valuta- must take these criteria into account diese Kriterien bei der Bewertung der
re l’attitudine alla guida di una persona. when assessing whether or not a per- Fahrtüchtigkeit einer Person berücksi-
son will make a suitable driver. chtigen.
- Prendere confidenza con il carrello - Get to know the telescopic fork lift
- Machen Sie sich vor jedem Einsatz mit
elevatore telescopico sul terreno dove truck on the terrain where it is to be
dem Teleskoplader und den
sarà utilizzato. used.
- Trasportare il carico in posizione bassa - Transport the load with the boom Geländegegebenheiten vertraut...
e il braccio telescopico rientrato al lowered and fully retracted - Transportieren Sie die Last in niedriger
massimo . - Position the forks at right-angles to the Stellung und mit ganz eingefahrenem
- Posizionare le forche load to be lifted. Teleskoparm .
perpendicolarmente al carico da - Drive the truck at a speed appropriate - Positionieren Sie die Gabelzinken waa
sollevare. to conditions and the state of the gerecht zu der anzuhebenden Last.
- Guidare il carrello ad una velocità ground. - Fahren Sie den Gabelstapler mit einer
adeguata alle condizioni e allo stato - Never go too fast or brake sharply with den Bedingungen und dem Zustand
del terreno. a load. des Untergrunds angepaßten
- Non andare mai troppo forte né frenare - When picking up a load, check that the Geschwindigkeit.
bruscamente con un carico . ground is as even as possible. - Vermeiden Sie beim Fahren mit Last
- Al momento di prendere un carico, zu hohe Geschwindigkeit und abrupte
verificare che il terreno sia il più Bremsmanöver.
uniforme possibile . - Vergewissern Sie sich vor dem
Aufnehmen einer Last, daßder
Untergrund ausreichen tragfähig und
eben ist
- Non tentare di compiere operazioni - Never attempt to carry out operations - Achten Sie auf die ordnungsgemäße
che superino le capacità del carrello which exceed the lift truck’s capabili Verwendung der Steuer - und
elevatore. ties. Bedieneinrichtungen.
- Non sollevare un carico superiore alla - Never raise a load in excess of the
- Versuchen Sie keinesfalls, Arbeiten
capacità del carrello elevatore e non lift truck’s capacity and never increase
durchzuführen, die die Tragfähigkeit
aumentare la dimensione del the size of the ballast.
contrappeso. - Drive around obstacles. des Teleskopladers überschreiten.
- Girare intorno agli ostacoli. - Take care over electrical wires, tren - Heben Sie keinesfalls eine Last an, die
- Fare attenzione ai cavi elettrici, ai ches and recently-excavated or filled die Tragfähigkeit des Gabelstaplers
fossi, ai terreni scavati da poco o ground. übersteigt und erhöhen Sie keinesfalls
riportati. - Never leave the engine running das Ausmaß des Kontergewichtes.
- Non lasciare mai il motore acceso in unattended.
- Fahren Sie um Hindernisse herum.
assenza del guidatore. - Use the parking brake when depositing
- Utilizzare il freno di stazionamento per difficult loads or on sloping ground. - Achten Sie auf
deporre un carico difficile o su un - Never leave the truck parked with a Stromkabel,Freileitungen, Gräben,
terreno in pendenza. raised load. Frisch ausgehobene oder ange
- Non lasciare in nessun caso il carrello - Never authorise anyone to approach schüttete Böden.
in parcheggio con un carico sollevato. or pass below a load. Den Motor in Abwesenheit des Fahres
- Non autorizzare nessuno ad avvicinar - Always think of safety and only tran abstellen.
si o a passare sotto un carico. sport
-Benutzen Sie die Feststellbremse zum
- Pensare sempre alla sicurezza e well balanced loads.
trasportare solamente dei carichi ben - Never lift a load using one fork only. absetzen der Last oder bei Gefälle.
equilibrati. - Drive with care and with reflexes alert. - Den Teleskoplader niemals mit angeho
- Non sollevare mai un carico utilizzan - When the lift truck is not in use, lower bener Last abstellen.
do solamente una forca. the forks to the ground and engage the Achten Sie darauf, daß sich keine
- Guidare con prudenza e prontezza di parking brake. Personen im Gefahrenbereich der
riflessi. - Never leave the ignition key in the Maschine oder der Last befinden.
- Quando il carrello elevatore non viene truck unattended.
-Aus Sicherheitsgründen, ermitteln Sie
utilizzato, abbassare al suolo le forche - Never leave the truck loaded on a
e inserire il freno di stazionamento. gradient of over 15% even with the immer den Lastschwerpunkt der
- Non lasciare mai la chiave parking brake engaged. Ladung vor dem Anheben oder dem
d'avviamento sul carrello in assenza - When lifting a load, take care that Transport.
del guidatore. nothing and no-one interferes with the -Fahren Sie immer mit angepasster
- Non lasciare il carrello carico su una movement and adopt proper handling Geschwindigkeit, erhöhter
pendenza superiore al 15% anche con procedures only. Aufmerksamkeit und der nötigen
il freno di stazionamento inserito. - Comply with the data provided in the
Vorsicht.
- Quando si effettua il sollevamento di load diagrams.
un carico, fare attenzione che nulla o - Never transport another person on the -Nach dem Abstellen des
nessuno intralci il movimento ed evita lift truck. Teleskopladers, ziehen Sie die
re di effettuare false manovre. Feststellbremse an und senken Sie die
- Attenersi ai dati indicati sui diagrammi Gabelzinken auf den Boden ab.
di carico. - Beachten Sie die in den
- Non trasportare mai un’altra persona Traglastdiagrammen angegebenen
sul carrello elevatore.
Daten.
- Transportieren Sie niemals weitere
Personen auf dem Gabelstapler.
Ogni volta che si cambia un attrezzo, Whenever an implement is changed, to Jedesmal wenn ein Anbaugerät
per evitare di danneggiare i raccordi prevent damage to the hydraulic unions ausgewechselt werden soll, beachten
idraulici occorre: Sie folgende Punkte, um Schäden an
always proceed as follows: den Hydraulikanschlüssen zu
- arrestare il motore termico - Stop the engine vermeiden:
- aspettare circa 1 minuto per togliere la - wait 1 minute for the circuit to
- Lassen Sie den Druck ab, indem Sie
pressione del circuito depressurise
den
Inoltre controllare la pulizia di questi Moreover check that the unions are
clean. Verteilerhebel betätigen.
raccordi.
- Ensure that the coupling faces are - Vergewissern Sie sich stets, daß diese
clean. Anschlüsse sauber sind.
- Leggere con attenzione e comprende- - Read the operator's manual carefully, - Die Bedienungsanleitung sorgfältig
re il manuale d'istruzioni. making sure you understand it. lesen und sicherstellen,daßdie Inhalte
- Il manuale d'istruzione deve sempre - The operator’s manual must always be und Vorgehensweisen verstanden wur-
trovarsi al suo posto nel carrello eleva- kept in the lift truck, in the place provi- den..
tore ed essere nella lingua parlata dal ded and in the language understood by - Die Bedienungsanleitung muß sich
carrellista. the operator. ständig an der dafür vorgesehenen
- Osservare le norme di sicurezza e le - Respect the safety notices and instruc- Stelle im Teleskoplader befinden und in
istruzioni descritte per il carrello tions given on the lift truck. der vom Fahrer gesprochenen Sprache
elevatore. - It is compulsory to replace all plates or sein.
- Sostituire imperativamente tutte le stickers which are no longer legible or - Die Sicherheitsvorschriften und die auf
targhette o gli adesivi diventati illeggibi which have become worn or damaged. dem Gabelstapler beschriebenen
li o deteriorati. Anweisungen beachten.
- Unbedingt alle Beschriftungen oder
Aufkleber ersetzen, welche verschlis-
sen, unleserlich oder.
- L'utilizzatore che constata che il suo - The user must immediately advise his - Sollte der Benutzer feststellen, daß der
carrello elevatore non funziona bene o superior if his lift truck is not in good Gabelstapler sich nicht in betriebsbe-
non risponde alle norme di sicurezza, working order or does not comply with reitem Zustand befindet oder nicht den
deve informare immediatamente il the safety notice. Sicherheitsvorschriften entspricht, muß
responsabile. - The operator is prohibited from er dies sofort seinem Vorgesetzten mit-
- È vietato al conduttore effettuare lui carrying out any repairs or adjustments teilen.
stesso qualsiasi riparazione o regola- himself, unless he has been trained for - Es ist dem Fahrer untersagt, selbst
zione a meno che non sia stato forma- this purpose. He must keep the lift Reparaturen oder Einstellungen vorzu-
to per tale compito. Dovrà tenere il suo truck properly cleaned if this is among nehmen, es sei denn er wurde hierzu
carrello elevatore in perfetto stato qua- his responsibilities. ausgebildet. Wenn ihm dies übertragen
lora ne sia stato incaricato. - Carry out daily maintenance (See wurde, muß er seinen Gabelstapler
- Effettuare la manutenzione giornaliera chapter : A - DAILY OR EVERY 10 selbst in einem einwandfreien
(Vedi capitolo : A - OGNI GIORNO O HOURS SERVICE in paragraph : 3 - Betriebsicheren Zustand halten.
OGNI 10 ORE DI FUNZIONAMENTO MAINTENANCE). - Durchführung der täglichen
nella parte : 3 - MANUTENZIONE). - Ensure tyres are adapted to the nature Wartungsarbeiten: (Siehe Kapitel : A -
- Verificare che i pneumatici siano ade- of the ground (See area of the contact TÄGLICH ODER ALLE 10 BETRIEBS-
guati al tipo di terreno (Vedi superficie surface of the tyres in the chapter : STUNDEN, Abschnitt : 3 - WAR-
di contatto al suolo dei pneumatici, CHARACTERISTICS in paragraph : 2 - TUNG).
capitolo : CARATTERISTICHE nella DESCRIPTION). - Überzeugen Sie sich, daß die Reifen
parte 2 - DESCRIZIONE) für die Bodenart geeignet sind (Siehe
TECHNISCHE DATEN, Abschnitt : 2 -
BESCHREIBUNG).
Non usare i pneumatici consumati o Do not use a worn or damaged tyre verschlissenen oder beschädigten Rei-
deteriorati fen nicht benutzen
Montare pneumatici gonfiati con schiu- The fitting of foam inflated tyres is prohi- Das Aufziehen von mit "geschäumten
ma poliuretanica è vietato e non è bited and is not guaranteed by Reifen jeglicher Art ist untersagt und wird
garantito dal costruttore, salvo autoriz- the manufacturer, excepting prior nicht vom Hersteller gewährleistet, es sei
zazione. authorisation. denn, er hat eine vorherige Freigabe
erteilt.
- For your own and other people's
- Per la vostra sicurezza e quella altrui, safety, it is forbidden to modify the - Für Ihre Sicherheit und die Sicherheit
non modificate voi stessi la struttura o structure and settings of the various Dritter ist es untersagt, die Struktur und
la regolazione dei vari componenti del components of your lift truck yourself die Einstellungen der verschiedenen
carrello elevatore (Pressione idraulica, (Hydraulic pressure, relief valve cali- Komponenten des Teleskoplade selbst
taratura dei limitatori, regime motore, bration, I.C. engine running speed, zu verändern (Hydraulikdruck,
montaggio di attrezzature supplemen- addition of extra equipment etc.). The Einstellung der Begrenzungsventile,
tari, ecc.). Lo stesso vale per la disatti- same holds with regard to any sup- Motordrehzahl, Hinzufügen von
vazione o la modifica dei sistemi di pression or modification of the safety Zusatzausstattungen, usw.). Das glei-
sicurezza. In questi casi, il costruttore systems, in which case the maker che gilt für die Änderung oder
sarà svincolato da ogni responsabilità. would no longer be liable. Entfernung der
Sicherheitsvorrichtungen. In solchen
Fällen ist die Haftung des Herstellers
ausgeschlossen.
Per mantenere il carrello elevatore in Regular inspection of your lift truck is Um die Konformität des Teleskopladers
“stato di conformità”, è obbligatorio mandatory if it is to be kept in confor- zu gewährleisten, muß dieser
effettuare controlli periodici. La frequen- ming condition. The frequency of such regelmäßig einer Untersuchung unter-
za dei controlli è definita dalla normativa checks are defined by the current legi- zogen werden, wobei die
vigente nel paese d’utilizzo del slation of the country in which the lift Prüfungshäufigkeit von der
carrello elevatore. truck Gesetzgebung des jeweiligen
Le operazioni di manutenzione o le ripa- is being operated. Einsatzlandes des Teleskopladers vor-
razioni non riportate nella parte : 3 - Maintenance or repairs other than those gegeben wird.
(MANUTENZIONE) devono essere detailed in part : 3 - (MAINTENANCE) Die Wartung oder die Reparaturen, die
effettuate da personale qualificato (Per must be carried out by qualified person- nicht in Teil : 3 - (WARTUNG) beschrie-
maggiori informazioni, rivolgetevi al nel (Consult your agent or dealer) and ben sind, müssen von qualifiziertem
vostro agente o concessionario) e under the necessary safety conditions Personal durchgeführt werden (wenden
rispettando le condizioni di sicurezza to maintain the health of the operator Sie sich an Ihren oder
atte a garantire la vostra and any third party. Vertragshändler). Bei allen
incolumità e quella altrui. Wartungsarbeiten sind die entsprechen-
den Sicherheitsvorschriften und
Umweltvorschriften des jeweiligen
Einsatzlandes des Teleskoplader zu
beachten
- Dotare il carrello elevatore di un estin- - A lift truck operating in an area without - Sollte der Gabelstapler in einem
tore qualora la macchina venga utiliz- fire extinguishing equipment must be Umfeld ohne Löschmittel eingesetzt
zata in un luogo sprovvisto di mezzi equipped with an individual extingui- werden, muß er mit einem eigenen
d'estinzione. Esistono soluzioni opzio- sher. There are optional solutions, con- Feuerlöscher ausgestattet werden. Es
nali. Per maggiori informazioni, rivolge- sult your agent or dealer. gibt entsprechende
tevi al vostro agente o concessionario. - Take into account climatic and atmo- Sonderausstattungen, fragen Sie Ihren
- Tenere sempre conto delle condizioni spheric conditions of the site of utilisa- oder Vertragshändler.
climatiche ed atmosferiche del luogo di tion. - Klimatische und atmosphärische
utilizzo. Bedingungen des Einsatzortes berück-
sichtigen
Il pieno di lubrificanti è già stato effettua- For operation under average climatic Die Schmiermittel werden im Werk für
to in fabbrica, utilizzando lubrificanti per conditions, i.e. : between -15 °C and durchschnittliche Klimabedingungen ein-
condizioni climatiche d'uso medie, ossia + 35 °C, correct levels of lubricants in all gefüllt, d. h. -15°C bis + 35°C. Für stren-
da -15°C a + 35°C. Per un utilizzo in the circuits are checked in production. gere Einsätze muß der Gabelstapler vor
condizioni estreme occorre, prima del- For operation under more severe clima- der Inbetriebnahme entleert und mit für
l'avviamento, svuotare e rifare i pieni, tic conditions, before starting up, it is die Umgebungstemperaturen geeigne-
necessary to drain all the circuits, then
utilizzando i lubrificanti adatti a tali tem- ten Schmiermitteln gefüllt werden. Dies
ensure correct levels of lubricants using
perature. Lo stesso vale per il liquido di gilt auch für das Kühlmittel.
lubricants properly suited to the relevant
raffreddamento. ambient temperatures. It is the same for
the cooling liquid.
• Protezione dal gelo (Vedi capitolo : • Protection against frost (See chapter : • Frostschutz (Siehe Kapitel : SCH-
LUBRIFICANTI E CARBURANTE nella LUBRICANTS AND FUEL in para- MIERMITTEL UND KRAFTSTOFF,
parte : 3 - MANUTENZIONE). graph : 3 - MAINTENANCE). Abschnitt : 3 - WARTUNG).
• Impiego di lubrificanti adeguati (Per • Adaptation of lubricants (Ask your • Anpassung der Schmiermittel
maggiori informazioni rivolgetevi al dealer for information). (Erkundigen Sie sich bei Ihrem oder
vostro agente o Concessionario). • Engine filtration. Vertragshändler).
• Filtri motore. • Lighting (Working headlight). • Motorölfilter.
• Luci (Faro di lavoro). Optional solutions exist, consult your • Beleuchtung (Arbeitsscheinwerfer).
Esistono altre soluzioni opzionali. Per dealer. Es gibt Sonderausstattungen, fragen Sie
maggiori informazioni rivolgetevi al Ihren oder Vertragshändler.
vostro agente o concessionario.
L'utilizzo del carrello elevatore è vietato Use of a lift truck is prohibited in protec- Der Einsatz des Teleskopladers in EX -
negli spazi protetti (Es. : Raffinerie, ted areas (e.g. refinery, explosive atmo- geschützten Räumen ist untersagt (Z.
atmosfera esplosiva). Per l'utilizzo in sphere). For use in these areas, B. Raffinerie, explosionsgefährdete
questi spazi, esistono attrezzature specific equipment is available as an Atmosphäre). Für einen Einsätze in sol-
opzionali specifiche. Rivolgetevi al option. Consult your dealer. chen Räumen gibt es
vostro agente o concessionario. Sonderausstattungen. Fragen Sie Ihren
oder Vertragshändler.
- Indossare indumenti idonei alla guida - Wear clothes suited for driving the lift - Zum Führen eines Gabelstaplers geei-
del carrello elevatore, evitando quelli truck, avoid loose clothes. gnete Kleidung tragen, weite Kleidung
troppo larghi. - Never operate the vehicle when hands vermeiden.
- Non guidare mai con mani o scarpe or feet are wet or soiled with greasy - Niemals mit feuchten oder fettigen
umide o sporche di grasso. substances. Händen oder Schuhen fahren.
- Per un miglior comfort, regolare il - For increased comfort, adjust the dri- - Für einen besseren Komfort, den
sedile del conduttore e adottare una ver’s seat to your requirements and Fahrersitz passend einstellen und eine
buona posizione di guida. adopt the correct position in the dri- sichere Sitzposition im Führerstand
- Il conduttore deve sempre mantenere ver’s cab. annehmen.
la posizione normale di guida. È vieta- - The operator must always be in his - Es ist verboten, Arme, Beine oder,
to sporgere braccia e gambe e, in normal position in the driver’s cab. It is generell, irgendein Körperteil über den
generale, qualunque parte del corpo, prohibited to have arms or legs, or Führerstand des Teleskoplader hinau-
fuori del posto di guida del carrello ele- generally any part of the body, protru- sragen zu lassen.
vatore. ding from the driver’s cab of the lift - Immer den Sicherheitsgurt anlegen
- Allacciare e regolare sempre la cintura truck. und passend einstellen.
di sicurezza. - Always remember to fasten your seat - Die Bedienelemente dürfen auf keinen
- Gli organi di comando non devono mai belt and adjust it to your requirements. Fall zu einem anderen als dem
essere utilizzati per scopi differenti da - The control units must never in any Bestimmungszweck verwendet werden
quelli a cui sono preposti (Es. : Salire o event be used for any other than their (Z. B. Auf- und Absteigen vom
scendere dal carrello elevatore, appen- intended purposes (e.g. climbing onto Gabelstapler, Kleiderhaken, usw.).
dere indumenti, ecc.). or down from the lift truck, portman- - Sollten die Bedienelemente mit einem
- Quando gli strumenti di comando sono teau, etc.). System für erzwungenen Betrieb
dotati di un dispositivo di marcia forza- - If the control components are fitted ausgestattet sein (Hebelblockierung),
ta (bloccaggio della leva), è vietato with a forced operation (lever lock) ist es verboten, den Führerstand zu
lasciare il posto di comando prima di device, it is forbidden to leave the cab verlassen, ohne vorher diese
rimettere tali comandi in folle. without first putting these controls in Steuerungen in Neutralstellung zu brin-
- Non far salire mai passeggeri sul neutral. gen.
carrello elevatore o nel posto di guida. - Never allow a passenger to travel on - Niemals Mitfahrer auf dem
the lift truck in the driver’s cab. Teleskoplader und im Führerstand
zulassen.
B - Prima di avviare il carrello B - Before starting the lift truck. B-Vor dem Starten des
elevatore. Teleskoplader.
- Se il carrello elevatore è nuovo, riferirsi - If the lift truck is new, refer to chapter :
al capitolo : PRIMA DI AVVIARE UN BEFORE STARTING UP A NEW LIFT - Ist der Teleskoplader neu, siehe
CARRELLO ELEVATORE NUOVO TRUCK in paragraph : 1 - OPERA- Kapitel : VOR DER INBETRIEBNAH-
nella parte : 1 - ISTRUZIONI E TING AND SAFETY INSTRUCTIONS. ME EINES NEUEN
NORME DI SICUREZZA. - Check the condition of the tyres and TELESKOPLADER, Abschnitt : 1 -
- Controllare lo stato e la pressione dei the tyre pressures (See chapter : CHA- ANWEISUNGEN UND
pneumatici (Vedi capitolo : CARATTE- RACTERISTICS in paragraph : 2 - SICHERHEITSVORSCHRIFTEN.
RISTICHE nella parte : 2 - DESCRI- DESCRIPTION). - Die Reifen auf ihren Zustand und den
ZIONE). - Before starting the lift truck, check the Reifendruck prüfen (Siehe Kapitel :
- Prima dell'avviamento verificare i vari different levels : TECHNISCHE DATEN, Abschnitt : 2 -
livelli : • Engine oil. BESCHREIBUNG).
• Olio motore termico. • Hydraulic reservoir oil. - Vor dem Start des Teleskoplader, die
• Olio serbatoio idraulico. • Transmission oil. verschiedenen Flüssigkeitsstände
• Olio trasmissione. • Cooling liquid. überprüfen :
• Liquido di raffreddamento. • Motorölstandprüfen.
- Also check for possible leakage of oil, • Hydraulikölstand prüfen.
- Controllare anche le eventuali perdite fuel or liquid from the lift truck. •Getriebeölstand prüfen.
d'olio, di combustibile o di liquido sul • Kühlmittelstand prüfen.
carrello elevatore.
- Den Teleskoplader ebenfalls auf
Undichtigkeiten von Öl, Kraftstoff bzw.
Flüssigkeit überprüfen.
- Accertarsi della corretta chiusura e del - Check the closing and locking of the - Vergewissern Sie sich, daß alle
bloccaggio del cofano motore. hood. Zugangsklappen verschlossen und ver
- L’utilizzatore, qualunque sia il suo - Whatever his experience as a truck dri- riegelt sind
grado di esperienza come carrellista, ver is, the operator is advised to fami- - Machen Sie sich mit dem
dovrà familiarizzarsi con la posizione e liarize himself with the position and Teleskoplader,der Lage und Funktion
l'utilizzo di tutti gli strumenti di controllo operation of all the controls and instru- der Bedien- und Steuerelementen vor
e di comando, prima di mettere il car- ments before operating the lift truck. Fahrtantritt vertraut.
rello elevatore in servizio.
C - Avviamento del carrello C - Starting the lift truck. C - Starten des Teleskoplader.
elevatore.
Safety notice. Sicherheitsvorschriften.
Norme di sicurezza.
Il carrello elevatore può essere avviato The lift truck must only be started up or Der Teleskoplader darf erst gestartet
o manovrato solo quando il conduttore manoeuvred when the operator is sitting oder bedient werden, wenn der Fahrer
si trova al posto di guida, con la cintura in the driver’s cab, with his seat belt im Führerstand sitzt und den
di sicurezza allacciata e regolata. adjusted and fastened. Sicherheitsgurt eingestellt und angelegt
hat.
- Non trainare o spingere il carrello - Never try to start the lift truck by - Den Teleskoplader zum Starten nicht
elevatore per avviarlo. pushing or towing it. ziehen oder schieben.
Tale manovra potrebbe provocare gravi Such operation may cause severe Eine solche Bedienung würde schwere
deterioramenti alla trasmissione. damage to the transmission. If neces- Beschädigungen am Übersetzungsge-
Qualora fosse necessario trainare il car- sary, to tow the lift truck in an emer- triebe hervorrufen. Sollte das
rello elevatore, mettere il cambio in gency, the gear-box must be placed in Abschleppen des Teleskopladers erfor-
posizione neutra(Vedi capitolo : H3 - the neutral position (See chapter : H3 - derlich sein: (Siehe Kapitel :
nella parte : 3 - MANUTENZIONE). in paragraph : 3 - MAINTENANCE). H3 -Abschnitt : 3 - WARTUNG).
- Verificare che la leva dell'invertitore di - Make sure that the forward/reverse - Überzeugen Sie sich davon, daß sich
marcia sia in folle. lever is in neutral. der Fahrtrichtungswahlschalter in der
- Ruotare la chiave di avviamento in - Turn the ignition key to the position I to Neutralstellung befindet.
posizione I per consentire il contatto activate the electrical system. - Den Zündschlüssel in Stellung I
elettrico. - Check the level on the fuel level drehen, um den elektrischen Kontakt
- Controllare il livello del carburante gauge. herzustellen.
sull'indicatore. - Turn the ignition key to position II to - Den Kraftstoffstand auf der Anzeige
- Ruotare la chiave di avviamento in preheat for 15 seconds. (If the überprüfen.
posizione II per permettere il environmental conditions require it) - Den Zündschlüssel in Stellung II
preriscaldamento e attendere 15 drehen, um ein Vorwärmen von 15
secondi. (Se le condizioni ambientali lo Sekunden zu ermöglichen.
richiedano) (Wenn die Umgebungsbedingungen es
verlangen)
Non attivare il motorino di avviamento Do not engage the starter motor for Den Anlasser nicht länger als 15
per più di 15 secondi, e consentire il more than 15 seconds and carry out the Sekunden betätigen, und zwischen
preriscaldamento durante 10 secondi preheating for 10 seconds between allen erfolglosen Startversuchen ein
tra tutti i vari tentativi effettuati. unsuccessful attempts. Vorwärmen während 10 Sekunden dur-
chführen.
- Premere l'acceleratore e ruotare fino in - Press the accelerator pedal and turn - Das Gaspedal niederdrücken und den
fondo la chiave di avviamento, il moto- the ignition key fully : the I.C. engine Zündschlüssel bis zum Anschlag
re dovrebbe avviarsi. Rilasciare la should then start. Release the ignition drehen, der Motor muß nun ansprin-
chiave di avviamento e lasciare girare key and let the I.C. engine run at idle. gen. Den Zündschlüssel wieder loslas-
il motore a basso regime. - Before operating in very cold environ sen und den Motor im Leerlauf drehen
- Prima di operare in ambienti climatici ments wait for the I.C. engine and lassen.
molto freddi attendere il corretto hydraulic systems to heat up - Bevor man unter sehr kalten
riscaldamento del motore termico e adequately. Klimaverhältnisse arbeitet, abwarten,
degli impianti idraulici. dass der Motor und die hydraulischen
Anlagen richtig warm geworden sind.
.
10
- Osservare tutti gli strumenti di controllo - Check all control instruments immedia- - Sofort nach dem Anspringen, wenn der
immediatamente dopo l'avvio, con il tely after starting up, when the I.C. Motor warm ist, und in regelmäßigen
motore caldo, e ad intervalli regolari engine is warm and at regular intervals Abständen während des Einsatzes alle
durante l'utilizzo, in modo da individua- during use, so as to quickly detect any Kontrollinstrumente beobachten, um
re e risolvere rapidamente le eventuali faults and to be able to correct them eventuelle Anomalien festzustellen
anomalie. without any delay. und so schnell wie möglich Abhilfe zu
- Se uno degli strumenti segnala un'ano- - If an instrument does not show the cor- schaffen.
malia, spegnere il motore e provvedere rect display, stop the I.C. engine and - Sollte ein Instrument nicht korrekt
immediatamente alle operazioni neces- immediately carry out the necessary anzei
sarie. operations. gen, Motor sofort abstellen und die
notwendigen Maßnahmen veranlas-
sen..
D - Guida del carrello elevatore D - Driving the lift truck D - Fahren des Teleskoplader
- Effettuare gli spostamenti del carrello - Always drive the lift truck with the forks - Ein Verfahren des Gabelstaplers immer
elevatore sempre con le forche o l'ac- or attachment at approximately 300 mit den Gabelzinken oder dem
cessorio a circa 300 mm dal suolo, mm from the ground, i.e. In the tran- Anbaugerät ca. 300 mm über dem
ossia in posizione di trasporto. sport position. Boden, d. h. in Transportstellung, dur-
- Esercitarsi alla guida del carrello - Familiarise yourself with the lift truck chführen.
elevatore sul terreno dove dovrà on the terrain where it will be used. - Machen Sie sich mit der Umgebung,
operare. - Ensure that the service brakes and the der Bodenbeschaffenheit und den
- Accertarsi dell'efficienza dei freni di sound alarm are working properly. Einsatzbedingungen für Ihren
servizio e del clacson. - Drive according to, and at an appro- Teleskoplader vertraut.
- Guidare in modo appropriato sceglien priate speed for, the conditions and -Überprüfen Sie vor Fahrtantritt die
do la velocità adeguata alle condizioni state of the terrain. Wirksamkeit der Fuß- und Handbremse
e al tipo di terreno. - Slow down before executing a turn. - Fahren sie mit angepasster
- Rallentare prima di effettuare una - In all circumstances make sure you are Geschwindigkeit, und den der Sicht -
svolta. in control of your speed. und Bodenverhältnissen gebotenen
- Aver in ogni circostanza il controllo del - On damp, slippery or uneven terrain, Vorsicht.
carrello e della rispettiva velocità. drive slowly. - Geschwindigkeit vor Kurven herabset-
- Su terreno umido, scivoloso o - Brake gently, never abruptly. zen herabsetzen.
sconnesso,condurre lentamente. - Only use the lift truck’s forward/reverse - Auf feuchtem, rutschigem oder unglei-
- Frenare progressivamente, evitare lever from a stationary position and chmäßigem Gelände, langsam fahren.
brusche frenate. never do so abruptly. - Langsam, und nicht ruckartig abbrem-
- Agire sull'invertitore di marcia del - Always remember that hydraulic type sen.
carrello elevatore soltanto a macchina steering is extremely sensitive to - Den Fahrtrichtungswahlschalter des
ferma evitando brusche manovre. movement of the steering wheel, so Teleskoplader nur bei völligem
- Ricordarsi sempre che lo sterzo di tipo turn it gently and not jerkily. Stillstand und ohne Gewalt betätigen.
idraulico è molto sensibile ai movimenti - Never leave the I.C. engine on when - Immer daran denken, daß eine hydrau-
del volante, quindi occorre sterzare the lift truck is unattended. lische Lenkung sehr empfindlich auf
progressivamente e non a scatti. - Look in the direction you are travelling Bewegungen des Lenkrads reagiert,
- Non lasciare mai il motore acceso in and always keep clear visibility of the daher die Lenkung mit entsprechen-
assenza del conduttore. road. Use the left and right rear view dem Feingefühl betätigen.
- Guardare sempre nella direzione di mirrors frequently and ensure that they - Vor dem Verlassen des Fahrerstandes
marcia e conservare una buona visibi- are kept in good condition, are clean den Motor abstellen.
lità del percorso. Utilizzare frequente- and correctly adjusted. - Immer in Fahrtrichtung blicken, die
mente gli specchi retrovisori laterali, e - Never use the truck in places poorly Fahrweise des Sichtverhältnissen
controllarne le condizioni, la pulizia e la lighted. anpassen.die Rückspiegel verwenden
regolazione. - When working at night, ensure that und darauf achten, daß diese entspre
- Non utilizzare il carrello in ambienti bui your lift truck is fitted with full beam chend eingestellt und sauber sind.
o scarsamente illuminati. lights. There are optional solutions, - Der wagen nicht in unbeleuchtenen
- Di notte, verificare che il carrello eleva- consult your agent or dealer. räumen und im wenigen licht nicht
tore sia dotato di luci di lavoro. - Drive round obstacles. benutzen.
Esistono soluzioni opzionali. Per mag- - Bei Nachtarbeit, darauf achten, daß
giori informazioni, rivolgetevi al vostro der Teleskoplader mit einem
agente o concessionario. Arbeitsscheinwerfer ausgestattet ist.
- Aggirare gli ostacoli. Es gibt Sonderausstattungen, fragen
Sie Ihren oder Vertragshändler.
- Hindernisse müssen umfahren werden.
11
- Non immettersi su un ponte di carico - Never move onto a loading platform - Niemals eine Ladebrücke befahren,
senza aver verificato : without having first checked : ohne vorher überprüft zu haben :
• Che sia correttamente posizionato ed • That it is suitably positioned and made • Befestigung Tragfähigkeit
ancorato. fast. Korrekte auflage und Befestigung
• Che il mezzo al quale è collegato • That the unit to which it is connected • Daß das Fahrzeug, mit dem sie
(Vagone, camion, ecc.) Non si possa (Wagon, lorry, etc.) will not shift. verbunden ist, (Waggon, Lkw, usw.)
spostare. • That this platform is prescribed for the nicht wegrollen kann.
• Che tale ponte possa sopportare il total weight of the lift truck to be loa • Daß die Brücke für das
peso totale del carrello elevatore e del ded. Gesamtgewicht
suo eventuale carico. • That this platform is prescribed for the des gegebenenfalls beladenen
• Che la larghezza del ponte sia width of the lift truck. Teleskoplader geeignet ist.
adeguata a quella del carrello - Never move onto a foot bridge, floor or • Daß die Ladebrücke für die Breite des
elevatore. freight lift, without being certain that Teleskoplader geeignet ist.
- Non immettersi mai su una passerella, they are prescribed for the weight and - Vor dem Befahren von Stegen, Böden
su un pianale o un montacarichi, senza size of the lift truck to be loaded and oder Lastenaufzügen, den Zustand,
avere la certezza che essi siano previ- without having checked that they are in die
sti per il peso e l'ingombro del carrello sound working order. Abmessungen und die Tragfähigkeit für
elevatore e del suo eventuale carico, e den ggf. beladenen Teleskoplader
senza aver verificato che essi siano in prüfen.
buono stato.
Prestare particolare attenzione alle ban- Take extreme care with loading Auf Laderampen, Gräben, Gerüste,
chine di carico, alle trincee, ai ponteggi, platforms, trenches, scaffolding, recen- kürzlich ausgehobens bzw. aufgefülltes
ai terreni recentemente scavati e/o tly dug and/or backfilled ground. Gelände achten.
riempiti.
- La velocità di circolazione del - The loaded lift truck must not travel - Die Fahrgeschwindigkeit des
carrello elevatore con carico non at speeds in excess of 10 km/h. beladenen
deve in nessun caso superare i Teleskoplader darf 10 km/h nicht
10 km/h. überschreiten.
12
Questa precauzione deve essere rispet- Ensure you comply wiyh this safety noti- Diese Vorsichtsmaßnahme bei
tata scrupolosamente nel caso di arresti ce as stopping the engine without
frequenti del motore termico, altrimenti häufigem Abschalten des Motors
allowing it to cool could cause damage beibehalten, um eine eventuelle
la temperatura di alcuni pezzi aumente- to components damaging such parts.
rebbe considerevolmente. Überhitzung durch mangelnde
Kühlleistung auszuschließen.
- Never leave the ignition key in the lift - Bei Verlassen des Fahrerstandes den
- Non lasciare mai la chiave di truck when the lift truck is unattended. Zündschlüssel abziehen.
avviamento sul carrello elevatore in - When the lift truck is stationary, place - Zum Abstellen des Teleskoplader die
assenza del conduttore. the forks or attachment on the ground, Gabelzinken oder das Anbaugerät auf
- Quando il carrello elevatore è fermo, place the gear lever in neutral, apply den Boden absenken, Handbremse
posare le forche o l'accessorio a terra, the parking brake and put the forward / anziehen und den
mettere la leva del cambio in folle, reverse lever in neutral. Fahrtrichtungswahlschalter in
azionare il freno di stazionamento e - If the driver has to leave his cab, even Neutralposition schalten.
mettere la leva dell'invertitore in folle. for a moment, it is essential to place - Ergibt keinen Sinn
- Se il conduttore deve lasciare, anche the gear lever in neutral, apply the - Sich davon überzeugen, daß der
momentaneamente, il posto di guida, parking brake and put the Teleskoplader nicht verkehrsbehin-
azionare il freno di stazionamento e forward/reverse lever in neutral. dernd abgestellt ist oder weniger als
mettere la leva dell'invertitore in folle. - Make sure that the lift truck is not stop- einen Meter von Eisenbahnschienen
- Assicurarsi che il carrello elevatore sia ped in any position that will interfere entfernt steht.
parcheggiato in modo da non impedire with the traffic flow and at less than - Bei längerem Abstellen an einem
la circolazione e lontano almeno un one metre from the track of a railway. Standort, den Teleskoplader gegen
metro dai binari della ferrovia. - In the event of prolonged parking on a Witterungseinflüsse schützen,
- In caso di stazionamento prolungato, site, protect the lift truck from bad insbesondere gegen Frost (Frostschutz
proteggere il carrello elevatore dalle weather, particularly from frost (Check überprüfen), hinteres Fenster sch
intemperie, particolarmente in caso di the level of antifreeze), close the rear ließen,
gelo (Controllare il livello del liquido window, lock the cab door and ensure Tür des Führerstands verriegeln, und
antigelo), chiudere il lunotto posteriore, that the hood is properly secured. sich davon überzeugen, daß die
chiudere a chiave la porta della cabina - In the event of prolonged parking on a Motorhaube verriegelt ist.
e il cofano motore. site, protect the lift truck from bad
weather, particularly from frost (Check
the level of antifreeze), close the rear
window and lock the cab door and the
hood.
- Parcheggiare il carrello elevatore su un - Park the lift truck on flat ground or on - Den Teleskoplader auf ebenem
terreno piano o con pendenza inferiore an incline lower than 15 %. Gelände oder einer Schräge mit einer
al 15 %. - Place the forward/reverse lever in Neigung unter 15 % abstellen.
- Mettere la leva dell'invertitore di marcia neutral. -Teleskopladeranhalten
in folle. - Apply the parking brake. -Fahrtrichtungswahlhebel in
- Azionare il freno di stazionamento. Neutralposition schalten.
- Handbremse anziehen.
- Hydrostatischer Antrieb
13
- Rientrare completamente il braccio. - Completely retract the boom. - Den Teleskop völlig einfahren.
- Posare a terra le forche o l'accessorio - Lower the forks or attachment to rest - Die Gabelzinken oder das Anbaugerät
bene in piano. on the ground. auf dem Boden absetzen
- Spegnere il motore termico - Stop the I.C. engine - - Motor abschalten
- Togliere la chiave di avviamento. - Remove the ignition key. - Druck in den Hydrokreisen durch
- Controllare che la porta sia chiusa a - Check the closing and locking of door, Betätigen den Hydrosteuerungen
chiave e che il lunotto posteriore e il rear window and hood. abbauen.
cofano motore siano anch'essi chiusi. - Zündschlüssel abziehen.
- Verschluß und Verriegelung der Tür,
des hinteren Fensters und der
Motorhaube überprüfen.
Prima di lasciare il posto di guida, assi- Before leaving your driver's cabin, Überzeugen Sie sich vor dem
curarsi di aver effettuato correttamente ensure that you have carried out all Verlassen des Führerstands davon,
tutte le operazioni di arresto del carrel- operations for stopping the lift truck, for daß alle Punkte zum Abstellen des
lo elevatore, e ciò per garantire la your safety and the safety of others. Gabelstaplers durchgeführt wurden.
vostra sicurezza e quella altrui. Dies ist für Ihre Sicherheit und für die
Sicherheit Dritter.
F - Guida del carrello elevatore su F - Driving the lift truck on the F - Fahren des Gabelstaplers auf
strada. public highway. öffentlichen Verkehrswegen.
- I conduttori di carrelli elevatori circolan- - Lift truck drivers, driving on the public - Fahrer von Gabelstaplern, die öffentli-
ti su strada devono osservare le dispo- highway, must abide by the general che Verkehrswegen fahren, müssen
sizioni generali relative alla circolazio- provisions relative to highway traffic. sich den allgemeinen Vorschriften des
ne stradale. - The lift truck must conform to the provi- Straßenverkehrs beugen.
- Il carrello elevatore deve essere sions of the Highway Code. If neces- - Der Teleskoplader muß den
conforme alle disposizioni del codice sary, optional solutions exist, consult Vorschriften der
stradale del vostro paese. In caso di your dealer. Straßenverkehrsordnung genügen.
necessità esistono soluzioni opzionali. Falls nötig gibt es
Per maggiori informazioni, rivolgetevi Sonderausstattungen, fragen Sie Ihren
al vostro agente o concessionario. oder Vertragshändler.
Il trasporto di carichi su strada è vietato Transport of loads on the public Das Befördern von Lasten auf öffentli-
e gli accessori montati sul carrello highway is forbidden and attachments chen Verkehrswegen ist untersagt und
elevatore devono essere dotati delle mounted on the lift truck must be fitted die auf dem Teleskoplader befestigten
attrezzature regolamentari o essere with equipment in accordance with Zubehörteile müssen mit den vorgesch-
smontati. regulations or else dismounted. riebenen Ausstattungen versehen oder
entfernt werden.
Istruzioni per la marcia su strada Instructions for driving on roads Anweisungen für den Straßenverkehr
- Verificare che il lampeggiante sia -Ensure that the flashing light is installed - Sicherstellen, dass die Rundum-
installato e funzionante. and is in perfect working order. Warnleuchte installiert ist und
- Luci anabbaglianti in funzione anche -Dipped headlights working also during funktioniert.
nelle ore e nelle strade in cui non hours and on roads where it is not obli - Abblendlicht auch in den Stunden und
ricorre l’obbligo dell’uso dei dispositivi auf den Straßen in Betrieb nehmen,
gatory to use visual and lighting
in denen die Benutzung der optischen
di segnalazione visiva e di illuminazione. indicator devices.
Meldevorrichtungen
- Controllare il buon funzionamento e la -Check the headlights, turn indicators und der Beleuchtung nicht vorgeschrie
pulizia dei fari, delle luci di direzione e and windscreen wipers to ensure they ben ist.
dei tergicristalli. are clean and in perfect working condi - Sicherstellen, dass die Scheinwerfer,
- Verificare la posizione degli specchi tion. die Blinker und die Scheibenwischer
retrovisori. -Check the position of the rear-view funktionieren und sauber sind.
- Die Einstellung der Rückspiegel
mirrors. prüfen.
14
- Controllare l'allineamento delle ruote e -Check wheel alignment and press the - Sicherstellen, dass die Räder gera
premere il selettore di sterzata in steering selector in the operating deaus stehen und den Modus
posizione di marcia con sole ruote position with only front wheel steering. Frontlenkung einstellen.
anteriori sterzanti. -Position the rear axle steering - Mechanische Lenksperre der
- Posizionare il blocco meccanico della mechanical block. Hinterachse einschalten.
sterzatura dell’assale posteriore -Ensure that the fuel level is sufficient. - Sicherstellen, dass genug Kraftstoff im
- Assicurarsi che la quantità di -Ensure that the truck is fitted with all Tank vorhanden ist.
combustibile sia sufficiente. the accessories required for traveling - Alle Zubehörteile montieren, die für den
- Montare tutti gli accessori previsti per on roads (depending on the model and Straßenverkehr (je nach Modell und
la circolazione stradale (secondo country). Land) vorgesehen sind.
modello e nazione). -Keep the boom retracted and the - Den Teleskopausleger ganz einfahren
- Mettere il braccio in posizione rientrato attachment about 300 mm above und das Anbaugerät auf circa 300 mm
e l'accessorio a circa 300 mm dal ground level. vom Boden bringen.
suolo. -Level the machine with the ch - Die Neigungsverstellung benutzen, um
- Livellare la macchina con il telaio assis parallel die Maschine so zu nivellieren, dass das
parallelo al suolo utilizzando il correttore to the ground using the slope corrector. Fahrgestell parallel zum Boden steht.
d’inclinazione. -Raise and retract the stabilizers to the - Stabilisatoren heben und maximal ein
- Sollevare e retrarre gli stabilizzatori al maximum. fahren.
massimo -Insert the rotation blocking pin. - Bolzen für Rotationssperre einstecken.
- Inserire perno di blocco rotazione -Cut out the operating system control by -Die Bedienelemente des Arbeitssystems
- Escludere i comandi del sistema lavoro means of the red button. mittels Red-Button ausschalten.
mediante red button -The vehicle can only circulate without - Das Fahrzeug darf nur im Leerzustand,
- Il mezzo può circolare solo a vuoto, load. d.h. ohne Ladung fahren.
ovvero senza carico. -The vehicle must not be used for tran - Der Transport von Personen an Bord
- Vietato il trasporto di personale di sporting the company personnel. der Arbeitsmaschine ist verboten.
scorta dell’impresa sulla macchina
operatrice
Su strada, non mettere l’inversore di While on the road, do not put the rever- Bei Straßenfahrten das Wendegetriebe
marcia in folle per disporre sempre del se gear in neutral to maintain lift truck nicht in die neutrale Stellung bringen,
freno motore del carrello elevatore. exhaust brake. um immer die Motorbremse des
Teleskopladers benutzen zu können.
15
H - Guida del carrello elevatore con H - Operating the lift truck with a H - Fahren des Teleskopladers auf
un accessorio anteriore su strada. front-end attachment on a public öffentlichen Verkehrswegen mit
highway. einem Anbaugerät.
- Per la guida con un accessorio, - For driving with an attachment, check - Für das Fahren mit einem Anbaugerät
consultare la regolamentazione vigente the regulations currently applicable in wird auf die jeweilige Gesetzgebubg
nel vostro paese. your country. des Einsatzlandes Verwiesen.- Das
- L’accessorio non può superare la - The attachment must not exceed the Zubehör darf die Breite über alles
larghezza massima del carrello overall width of the lift truck. des Gabelstaplers nicht überschreiten.
elevatore. - Do not mask the lighting range of the - Den Beleuchtungsbereich der vorderen
- Non ingombrare la zona d’illuminazio front headlamps. Scheinwerfer nicht abdecken.
ne dei fari anteriori. - Set the attachments shields in place - Den Zubehörschutz installieren
- Montare le protezioni sugli accessori - If necessary, fit the block spacer on the - Falls erforderlich, das Sperrelement
installati lifting and slewing cylinder. auf dem Hub- und Schwenkzylinder
- Se necessario mettere il distanziale di - Front dimensions of equipment anbringen.
blocco sul cilindro di sollevamento e di indicated on all three sides with 10 cm - Frontalen Überstand der Anbaugeräte
brandeggio. wide alternate white and red reflecting auf den drei Seiten mit rückstrahlenden
- Ingombro anteriore degli attrezzi stripes, slanting 45° Streifen melden, die abwechselnd weiß
segnalato sui tre lati con strisce (Follow the specific instructions for und rot,10 cm hoch und um 45°
retroriflettenti alternate di colore bianco each type of equipment) geneigt sind.
e rosso, alte 10 cm, inclinate 45° (Die spezifischen Anweisungen für
(Seguire le disposizioni specifiche per jedes Anbaugerät befolgen)
ogni attrezzo)
In caso di necessità, rivolgetevi al If necessary, consult your dealer. Im Zweifelsfall fragen Sie Ihren
vostro agente o concessionario. oder Vertragshändler.
16
- Verificare la conformità degli - Check that the lift truck’s attach - Vergewissern Sie sich, daß die
accessori alla taratura del sistema di ments are correctly calibrated to the Einstellung der
sicurezza della macchina. machine’s safety system
Sicherheitseinrichtung
- Verificare il buon funzionamento degli - Ensure the correct functioning of your
mit dem gewählten Anbaugerät übe
accessori del carrello elevatore. lift truck’s attachments.
- Do not attempt to carry out operations reinstimmt.
- Non effettuare operazioni che supera
no le capacità del carrello elevatore o which exceed the capacities of your lift - Überzeugen Sie sich von der einwand
dell'accessorio. truck or attachments. freien Funktion des Anbaugerätes.
- È vietato aumentare il valore di - It is prohibited to increase the - Versuchen Sie niemals Arbeiten durch
contrappeso qualunque sia l'artificio counterweight value in any way. zuführen, welche die in den
impiegato. - It is strictly prohibited to carry or to lift Traglastdiagrammen angegebenen
- È rigorosamente vietato trasportare o up persons using the lift truck, unless Werte überschreiten.
sollevare persone con il carrello eleva- the vehicle is specially equipped for - Alle Maßnahmen zur Erhöhung des
tore, a meno che il carrello non sia this purpose and has the correspon- Kontergewichtes sind Verboten.
attrezzato per tale scopo e fornito del ding certificate of conformance for lif-
- Der Teleskoplader ist nicht zur
certificato di conformità relativo al sol- ting people.
- Avoid travelling for a long distance in Personenbeförderung ausgelegt. Für
levamento di persone.
reverse. die Personenbeförderun gibt es eine
- Evitare di effettuare lunghi percorsi in
retromarcia. - When lifting or lowering the boom entspre chende Sonderausstattung.
-Eseguire manovre lente e progressive, ensure the control lever is moved slowly FRAGEN SIE
di salita e discesa del braccio telesco and smoothly (whether operating with or IHRENVERTRAGSHÄNDLER.
pico (Anche senza carico). without a load) -Rüchwärtsfahren über längere Strecken
ist zu vermeiden.
- Verificare che l'accessorio sia - Ensure that the attachment is correctly - Überzeugen Sie sich davon, daß das
correttamente installato e bloccato sul fitted and locked to its frame. Anbaugerät ordnungsgemäß montiert
suo supporto. - Ensure the correct attachment mode und verriegelt ist
- Verificare di aver impostato il sistema has been selected on the machine’s - Überprüfen Sie, das
di sicurezza in cabina conforme security system control panel. Sicherheitssystems
all’accessorio montato. - Conform to the limits on the load chart in der Kabine gemäß dem
- Rispettare i limiti del diagramma di for the attachment. verwendeten Anbaugerät
carico dell'accessorio. - Ensure that palettes, cases, etc, are in - Beachten Sie die Traglasttabellen des
- Verificare che i pallet, le casse, ecc., good order and suitable for the load to Teleskoplader und der Anbaugeräte
siano in buono stato e adeguate al be lifted. - Verwenden Sie ausschließlich geei-
carico da sollevare. - Position the forks perpendicular to the gnete
- Presentare le forche perpendicolarmente load to be lifted, taking account of the Lastaufnahmemittel
al carico da sollevare, tenendo conto load’s centre of gravity. - Zum Anheben der Last die
della posizione del centro di gravità del - Never lift a load with a single fork. Gabelzinken
carico. - Never lift a sling load with a single fork im im rechten Winkel zur zu
- Non sollevare mai un carico con una or with the carriage. Optional solutions Last ansetzen, dabei die Lage des
sola forca. exist, consult your dealer. Lastschwerpunktsbeachten.
- Non sollevare mai un carico imbracato - If not utilise, place the attachment in hori- - Niemals eine Last mit nur einer
zontal on the ground (For unstable atta- Gabelzinke anheben.
con una sola forca o con una tavola.
chments, ensure they are secured using - Niemals eine angeschlagene Last mit
Esistono delle soluzioni opzionali. Per
wedges). nur einer Gabelzinke oder mit der
maggiori informazioni, rivolgetevi al
- Place the attachments in the closed posi-
vostro agente o concessionario. Werzeugaufnahme anheben. Es gibt
- se non utilizzato mettere l'accessorio tion,
Sonderausstattungen, fragen Sie Ihren
in posizione orizzontale sul suolo flat on level ground (for unstable attach
Vertreter oder Vertragshändler.
(Puntellare correttamente gli accessori ments secure using wedges).
- Das Zubehörteil geschlossen eben auf
instabili). - Ensure that rapid hydraulic connec-
tions on the attachment system are den Boden legen (Bei instabilem
- Verificare che i raccordi rapidi idraulici
clean and protected. Zubehör, darauf achten, daß es gut ist).
del circuito accessorio siano puliti e
- Überzeugen Sie sich stets davon, daß
protetti.
die Hydraulikkupplungen sauber und
funktionstüchtig sind
Prima di ogni cambio di accessorio a Carry out the following procedure Vor jedem Wechsel eines Anbaugerätes
funzionamento idraulico, al fine di evita- before changing hydraulic attachments mit Hydraulikfunktionen und um
re il deterioramento dei raccordi rapidi to prevent damage to the quick relea- Beschädigungen an dender hydrauli-
idraulici occorre : se couplings schen Schnellkupplungen zu vermei-
den:
17
- Spegnere il motore termico. - Switch off the engine. - Den Verbrennungsmotor abschalten.
- Attendere circa 1 minuto per togiere la - Wait 1 minut to allow the circuit to - Den Druck des Hydrokreises für das
pressione nel circuito idraulico. depressurise. Zubehör durch Betätigen der
Hydrosteuerungen abbauen.
C - Condizioni ambientali d’uso. C - Environment.
- Verificare che ci sia una illuminazione - Verify that the lighting in suitable C - Umfeld.
adeguata - Ensure that no person or objet is in the - Nachprufen dab die beleuchtung
- Fare attenzione quando sollevate un vicinity before raising the load. Don’t richting ist
carico, che niente e nessuno ostacoli il make any incorrect manoeuvres. - Beim Anheben der Last darauf achten,
corretto svolgimento dell'operazione ed - In the case of work near aerial lines, daß sich Keine Personen oder
evitare ogni falsa manovra. ensure that the safety distance is suffi- Gegenstände im Gefahrenberich
- Nel caso di lavori eseguiti in prossimità cient between the working area of the aufhalten.
di linee elettriche aeree, assicurarsi lift truck and the aerial line. - Bei Arbeiten in der Nähe von
che la distanza di sicurezza, tra l'area Freileitungen, darauf achten, daß zwi
di lavoro del carrello elevatore e la schen dem Gabelstapler und der
linea elettrica, sia sufficiente. Freileitung ein ausreichender
Sicherheitsabstand eingehalten wird.
Informatevi presso la vostra agenzia You must consult your local electrical Bitte erkundigen Sie sich bei Ihrem
locale dell'azienda elettrica. agency.
örtlichen Stromwerk.
Rischiate di essere fulminati o di essere You could be electrocuted or seriously Sie können einen tödlichen
gravemente feriti se lavorate o parcheg- injured if you operate or park the lift Stromschlag bekommen oder schwer
giate il carrello elevatore troppo vicino truck too close to power cables. You are verletzt werden, wenn Sie zu nahe an
ai cavi elettrici. Quindi vi consigliamo strongly advised to ensure that the Freileitungen arbeiten bzw. den
vivamente di accertarvi che le regole di safety rules on the site conform to the Teleskoplader zu nahe daran abstellen.
sicurezza applicate sul sito siano local regulations in force regarding all
Es wird dringend empfohlen, sich
conformi alla vigente regolamentazione types of work carried out close to power
davon zu überzeugen, daß die
locale per quanto riguarda tutti i tipi di cables.
Sicherheitsregeln vor Ort mit der gel-
lavoro effettuati in prossimità di linee
elettriche. tenden örtlichen Gesetzgebung bezü-
glich Arbeiten in der Nähe von
Freileitungen übereinstimmen.
- Vietare a chiunque di avvicinarsi alla - Do not allow anybody to come near the
zona di manovra del carrello elevatore working area of the lift truck or pass - Stellen Sie sicher, daß sich keine
o di passare sotto un carico. beneath an elevated load. Personen im Gefahrenbereich des
- Per un utilizzo su terreni in pendenza, - When using the lift truck on a slope, Teleskoplader aufhalten
prima di alzare il braccio, controllare before raising the jib, ensure that the - Bei Einsatz des Teleskoplader auf
che il terreno sia orizzontale. Tuttavia, i ground is horizontal. However, lift einer Schräge sicherstellen, daß der
carrelli elevatori dotati di correttore di trucks fitted with a slope corrector Teleskoplader horizotal ausgerichtet
livello e/o di stabilizzatori, possono and/or stabilisers can work on a stee- ist. horizontal ist. Jedoch können
operare su pendenze trasversali, a per transverse slope providing this Gabelstapler mit einem
condizione di correggere questa incli- slope can be corrected (See paragraph Neigungsausgleich und/oder
nazione (Vedi paragrafo : G - : G - HORIZONTAL POSITION OF Stützfüßen auf einer stärkeren
ORIZZONTALITÀ DEL CARRELLO THE LIFT TRUCK in the chapter : Querneigung arbei ten, vorausgesetzt,
ELEVATORE nel capitolo : MOVIMEN- LOAD HANDLING). dass diese Neigung korrigiert wird
TAZIONE DI UN CARICO). (Siehe Absatz : G - HORIZONTALLA
GE DES GABELSTAPLERS im Kapitel
: HANDHABUNG EINER LAST).
18
- Osservare sempre le regole di sicurez- - Always consider safety and only tran- - Immer an die Sicherheit denken und
za, trasportare carichi sempre equili- sport balanced and correctly secured nur Lasten befördern, die ausgeglichen
brati e correttamente sistemati per evi- loads to avoid any risk of tipping. und richtig befestigt sind, um jegliches
tare ogni rischio di ribaltamento. - Fully engage forks under the load and Kippen zu vermeiden.
- Inserire a fondo le forche sotto il carico move it in the transport position (The - Die Gabeln ganz unter die Last fahren
e spostarlo in posizione di trasporto forks 300 mm from the ground, the jib und diese in Transportstellung bringen
(Le forche a 300 mm dal suolo, il brac- retracted to the maximum and the car- (die Gabeln 300 mm über dem Boden,
cio completamente rientrato e le forche riage sloping backwards). Ausleger eingefahren und
inclinate indietro). - For obvious reasons regarding the lift Werkzeugaufnahme nach hinten
- Per evidenti ragioni di stabilità del car- truck’s stability and clear visibility of the geneigt).
rello elevatore e di buona visibilità, surrounding environment, only move - Aus Gründen der Stabilität und des
spostate il carrello elevatore solo quan- the lift truck when the jib is in the tran- Überblicks darf mit dem Gabelstapler
do il braccio è in posizione di trasporto. sport position. nur gefahren werden, wenn der
- Manovrate il carrello elevatore con il - Do not manoeuvre the lift truck with the Ausleger in Transportstellung ist.
braccio sollevato solo in casi eccezio- jib in the raised position unless under - Den Gabelstapler nur in
nali; operate allora con estrema pru- exceptional circumstances and then Ausnahmesituationen mit angehobe-
denza, a velocità ridottissima e frenan- with extreme caution, at very low nem Ausleger bewegen, dabei äußerst
do molto dolcemente. Assicuratevi di speed and using gentle braking. vorsichtig vorgehen, und mit erheblich
avere sempre una visibilità sufficiente, Ensure that visibility is adequate and reduzierter Geschwindigkeit fahren und
eventualmente fatevi guidare da un'al- get another person to guide you along sanft abbremsen. Sich von einer
tra persona. if necessary. ausreichenden Übersicht überzeugen,
- Mantenere stabile il carico quando il - Never shift the position of the load gegebenenfalls eine weitere Person
carrello elevatore è in movimento. while the lift truck is in motion. hinzuziehen.
- Non avanzare mai troppo veloce- - Never drive too fast or brake abruptly - Die Last nicht bewegen solange der
mente, né frenare bruscamente con un when carrying a load. Gabelstapler in Bewegung ist.
carico. - During handling, drive at low speed. - Niemals mit einer Last zu schnell fah-
- Durante le operazioni di movimentazio- - Check the load, particularly when tur- ren oder zu plötzlich bremsen.
ne, circolare a velocità ridotta. ning corners and especially if it is very - Während der Handhabung im
bulky. Kriechgang fahren.
- Sorvegliare il carico, soprattutto nelle
- Secure unstable loads. - Die Last überwachen, besonders in
curve, in particolare se è voluminoso. - Handle loads with caution, at slow Kurven und insbesondere, wenn sie
- Imbragare i carichi instabili. speed, without sudden jerks when sehr sperrig ist.
- Movimentare i carichi con precauzione, moving them at significant heights and - Instabile Lasten befestigen.
a velocità ridotta e senza scatti, soprat- jib extention. - Lasten vorsichtig, bei geringer
tutto quando li portate a grandi altezze Geschwindigkeit und nicht ruckartig
handhaben, wenn sie in großen Höhen
e con notevole sbalzo.
oder bei großem Versatz bewegt wer-
den.
19
In caso di forte vento o tempesta, non In the event of high winds or storms, do Bei starkem Wind oder Sturm, keine
effettuare movimentazioni potenzial- not carry out handling work that jeopar- Handhabung vornehmen, die die
mente pericolose per la stabilità del car- dizes the stability of the lift truck and its Stabilität des Gabelstaplers und der
rello elevatore e del carico, load, Last gefährden könnte,
- Non cambiare direzione in modo
brusco e a velocità elevata.
- Do not change direction sharply and at -Keine Richtungswechsel oder ruckarti-
high speed. ge Lenkbewegungen bei hoher
Fahrgeschwindigkeit durchführen.
In caso di ribaltamento del carrello ele- In the event of the lift truck overturning, Sollte der Gabelstapler kippen, nicht
vatore, non tentare di uscire dalla cabi- do not try to leave the cab. D versuchen, die Kabine zu verlassen.
na durante l'incidente. BENUTZEN SIE DIE
DO NOT TRY TO JUMP CLEAR STAY
GUIDARE SEMPRE CON LE CINTURE SICHERHEITSGURTE!
IN THE CAB WITH YOUR SEAT BELT
DI SICUREZZA ALLACCIATE. DER BESTE SCHUTZ BESTEHT
FASTENED. DARIN, ANGESCHNALLT IM
RIMANERE CON LA CINTURA ALLAC-
CIATA NELLA CABINA,È LA VOSTRA - Apply the parking brake when lifting or FÜHRERSTAND ZU BLEIBEN.
MIGLIORE PROTEZIONE. depositing a difficult load or when on
- Zum Abladen oder Anheben einer
an incline. schwierigen Last oder auf schrägen
- Utilizzare il freno di stazionamento per - Do not stop the lift truck with the load Gelände die Handbremse benutzen.
posare o sollevare un carico difficile o in an elevated position. - Auf keinen Fall den Gabelstapler auch
su un terreno in pendenza. - Do not leave a laden lift truck with the nicht mit angehobenen Last abstellen.
- Non lasciare in alcun caso il carrello parking brake applied on an incline - Niemals den Gabelstapler, beladen
elevatore fermo con un carico which exceeds 15 %. oder unbeladen, mit angezogener
sollevato. Handbremse auf einer Schräge von
- Non lasciare il carrello elevatore, carico mehr als 15 % abstellen.
o vuoto, con il freno di stazionamento
azionato su una pendenza superiore al
15 %.
- Avere sempre una buona visibilità del - Constantly keep clear visibility of the - Sorgen Sie immer für freie Sicht nach
percorso, sia in visione diretta, che in road, either direct view (looking allen Seiten, um sicher zustellen, daß
visione indiretta ossia con gli specchi backwards when reversing) or indirect sich keine Personen im
retrovisori panoramici, per controllare view using the panoramic rear view Gefahrenbereich
la presenza eventuale di persone, ani- des Teleskopladers aufhalten.
mirrors to check for people, animals,
mali, buchi, ostacoli, variazioni di pen- - Sollte die Sicht aufgrund einer sperri-
holes, obstacles, change of slope, etc. gen Last bei Vorwärtsfahrt nicht ausrei-
denza... - Since visibility can be reduced on the chend sein, muß im Rückwärts fahren.
- La visibilità può venire ridotta sul lato right side when the jib is raised, ensure Diese Fahrweise muß jedoch eine
destro quando il braccio è alzato; quin- clear visibility of the road before raising Ausnahme bleiben und darf nur über
di assicurarsi della buona visibilità del the jib and before undertaking any kurze Strecken erfolgen.
percorso prima di alzare il braccio e manoeuvres. - Die Kennzeichnung und Beleuchtung
prima di manovrare. des Teleskopladers müssen den
- If the visibility in forward motion is not
- Se la visibilità in marcia avanti non è Ein Beleuchtungsstandard Rechnung
sufficient because of the bulkiness of
sufficiente a causa dell'ingombro del tragen.
the load, drive in reverse motion. This
carico, circolare in retromarcia. Tale Der Beleuchtungssystemstandard der
manovra ha un carattere eccezionale e manoeuvre must remain exceptional Maschine ist nicht für einen Gebrauch
può essere effettuata solo per brevi and for short distances. in sehr dunkler oder unbeleuchteter
distanze. - Ensure you have good visibility (Clean Umgebung geeignet. genügend.
- Assicuratevi di avere una buona windows, adequate lighting, correctly Zusätzlich zu der serienmäßig
visibilità (Vetri puliti, illuminazione adjusted rear view mirror, etc.). Ausstattung werden eine
sufficiente, retrovisore regolato, ecc.). - Signalling and lighting on the lift truck Reihe Sonderausstattungen
- I sistemi di segnalazione e le luci del must take account of the conditions of angeboten. Fragen Sie Ihren
carrello elevatore devono essere adatti use. The standard lighting system may oder Vertragshändler.
alle condizioni di utilizzo. not be sufficient for certain applications
L’illuminazione standard della macchi- or night time road use.
na non é sufficente per un uso in Optional accessories are available.
ambienti con scarsa luminosità o per Consult your agent or dealer. Im Zweifelsfall fragen Sie Ihren
uso notturno. Oltre alle attrezzature di oder Vertragshändler.
serie montate sul carrello elevatore,
esistono varie opzioni.Per maggiori
informazioni, rivolgetevi al vostro agen- If necessary, consult your dealer.
te o concessionario.
20
A - Peso del carico e centro di A - Weight of load and centre of A - Gewicht und Lastschwerpunkt
gravità. gravity.
Carrying a load greater than the rated Es ist verboten, eine Last aufzunehmen
È vietato sollevare e trasportare un
capacity for the lift truck or for the atta- oder zu transportieren, die größer als
carico superiore alla capacità nomina- die Nennkapazität des Teleskoplader
chment is prohibited.
le del carrello elevatore o dell’acces- oder des Anbaugerätes ist.
sorio.
- Before taking up a load, you must - Vor der Aufnahme einer Last müssen
- Prima di sollevare un carico, dovete deren Gewicht und Lastschwerpunkt
know its weight and its centre of
conoscerne il peso e il centro di bekannt sein.
gravity.
gravità. - The load chart relating to your lift truck - Das Lastdiagramm für den
- Il diagrama di carico relativo al vostro is valid for a weight with its centre of Teleskoplader gilt für eine Last, deren
carrello elevatore, è valido per un gravity 24 in. from the heel of the Schwerpunkt sich 500 mm gemessen
forks (Fig. A). For a load with a higher vom Gabelträger befindet (Abb. A).
carico il cui centro di gravità è a 500
centre of gravity, consult your agent or Sollte der Lastschwerpunkt größer
mm dal tallone delle forche (Fig. A). sein, fragen Sie Ihren oder
dealer.
Per un carico con centro di gravità - For irregular loads, determine the cen- Vertragshändler.
più distante, rivolgetevi al vostro tre of gravity in the transverse direction - Bei unregelmäßigen Lasten muß vor
agente o concessionario. before handling (Fig. B). jeder Handhabung der
Lastschwerpunkt bestimmt werden
- Per i carichi irregolari, determinare il
(Abb. B).
centro di gravità nel senso trasversa-
le prima di ogni movimentazione (Fig.
B).
Per i carichi con centro di gravità mobi- For loads with a moving centre of gra- Bei bestimmten Lasten mit bewegli-
le (ad esempio : liquidi), occorre tenere vity (e.g. liquids), take account of the chem Schwerpunkt (z. B. Flüssigkeit),
variations in the centre of gravity in müssen die Veränderungen des
conto delle variazioni del centro di gra-
order to determine the load to be hand- Schwerpunkts beim Festlegen der zu
vità per determinare il carico da movi- led (Consult your agent or dealer) and transportierenden Last berücksichtigt
mentare (rivolgetevi al vostro agente o be vigilant and take extra care to limit werden. (Wenden Sie sich an Ihren
concessionario), e porre particolare these variations as far as possible. Vertreter oder Vertragshändler). Dabei
attenzione e prudenza in modo da limi- ist mit der gebotenenVorsicht und
Aufmerksamkeit vorzugehen, um diese
tare al massimo queste variazioni.
Schwerpunktveränderungen zu begren-
zen.
A B C
21
B - Prelevare un carico dal suolo. B - Taking up a load on the ground. B - Aufnahme einer Last vom Boden.
- Avvicinare il carrello elevatore perpen- - Position the lift truck perpendicular to - Mit dem Teleskoplader die Last bei ein-
the load, with the jib retracted and the gefahrenem Ausleger und waagerech-
dicolarmente al carico, con il braccio
forks in a horizontal position (Fig. C). ten Gabelzinken rechtwinklig anfahren
rientrato e le forche orizzontali (Fig. C). - Adjust the fork spread and centering in (Abb. C).
- Regolare lo scarto e il centraggio delle connection with the load (Fig. D) - Abstand und Zentrierung der
forche rispetto al carico (Fig. D) (Optional solutions exist, consult your Gabelzinken der Last anpassen (Abb.
(Esistono soluzioni opzionali ; per mag- dealer). D) (Es gibt Sonderausstattungen, fra-
gen Sie Ihren oder Vertragshändler).
giori informazioni, rivolgetevi al vostro
agente o concessionario).
Attenzione ai rischi di pizzicamento o di Beware of the risks of trapping or squa- Beachten Sie die Gefahr eines
schiacciamento degli arti durante le shing limbs when manually adjusting Verklemmens oder Quetschens von
the forks. Always maintain an equal Körpergliedern beim manuellen
regolazioni manuali delle forche.
distance between the forks and the cen- Anpassen der Gabelzinken.. Halten Sie
Mantenere sempre una distanza uguale tre of the carriage in order to keep the immer gleichen Abstand zwischen den
tra le forche e l’asse centrale della tavo- load completely stable. Gabeln und der Mitte der
la per garantire la perfetta stabilità Werkzeugaufnahme,, damit die Last
del carico. stabil bleibt.
Inclinare sufficientemente il carico all’in- Tilt the carriage sufficiently backwards Neigen Sie die Last ausreichend weit
dietro per assicurarne la stabilità (perdi- to ensure the load’s stability when nach hinten, um ihre Stabilität sicherzu-
ta del carico durante la frenata) facendo braking whilst maintaining the load stellen (Gefahr des Abstürzens der Last
balance. beim Bremsen), ohne jedoch deren
però attenzione a non modificarne l’e-
Gleichgewicht zu beeinträchtigen.
quilibrio.
D E F
22
C - Prelevare un carico in alto su C - Taking up a high load on tyres. C - Aufnahme einer Last auf
pneumatici. Reifen.
È tassativamente vietato prelevare un Under no circumstances should you Sie dürfen eine Last auf keinen Fall auf-
carico se il carrello elevatore non è in pick up a load if the lift truck is not in a nehmen, wenn der Gabelstapler nicht
piano (Vedi paragrafo : G - horizontal position. (See paragraph : G - horizontal steht (Siehe Absatz : G -
ORIZZONTALITÀ DEL CARRELLO HORIZONTAL POSITION OF THE LIFT HORIZONTALLAGE DES GABELSTA-
ELEVATORE nel capitolo : MOVIMEN- TRUCK in the chapter : LOAD HAND- PLERS im Kapitel : HANDHABUNG
TAZIONE DI UN CARICO). LING). EINER LAST).
- Verificare che le forche passino facil- - Ensure that the forks will easily pass - Überzeugen Sie sich davon,, daß die
mente sotto il carico. under the load. Gabelzinken leicht unter der Last hin-
- Avvicinare il carrello elevatore perpen- - Position the lift truck perpendicular to durch passen.
dicolarmente al carico con le forche the load with the forks in a horizontal - Mit dem Teleskoplader die Last mit
orizzontali (Fig. G), manovrando dolce- position (Fig. G) manoeuvring gently waagerechten Gabeln rechtwinklig
mente e con prudenza (Vedi paragrafo and carefully (See paragraph : E - anfahren (Abb. G), dabei langsam und
: E - VISIBILITÀ nel capitolo : ISTRU- VISIBILITY in the chapter : HANDLING vorsichtig vorgehen (Siehe Absatz : E -
ZIONI PER LA MOVIMENTAZIONE INSTRUCTIONS for visibility of the SICHT im Kapitel : HANDHABUNG-
relativo alla visibilità sul percorso). road). SANWEISUNGEN für die Sicht auf die
Fahrbahn)).
Ricordandosi di mantenere sempre la Always think about keeping the distance Denken Sie immer daran, daß, zum
distanza necessaria per inserire le for- necessary to fit the forks under the load, Einführen der Gabelzinken unter der
che sotto il carico, tra la pila e il carrello between the pile and the lift truck (Fig. Last der notwendigen Abstand zwi-
elevatore (Fig. G), utilizzando la lun- G) and use the shortest possible schen der Last und dem Teleskoplader
ghezza minima possibile del braccio. length of jib. einzuhalten (Abb. G) dabei den
Teleskop so kurz wie möglich halten.
- Portare le forche contro il carico (Fig. - Stop with the forks in front of the load
H). Tirare il freno di stazionamento e (Fig. H). Apply the parking brake and - Die Gabelzinken vor der Last zum
mettere la leva dell'invertitore di marcia place the forward/reverse lever in neu- Anschlag bringen (Abb. H).
in folle. tral. Handbremse anziehen und den Hebel
- Sollevare leggermente il carico (1) e - Slightly lift the load (1) and incline the des Fahrtrichtungswahlschalters in
inclinare il portaforche (2) indietro per forks carriage (2) backwards to stabili- Neutralstellung bringen.
stabilizzare il carico (Fig. I). ze the load (Fig. I). - Die Last leicht anheben (1) und den
Gabelträger zum Stabilisieren der Last
nach hinten neigen (2) (Abb. I).
G H I
23
Inclinare sufficientemente il carico all’in- Neigen Sie die Last ausreichend weit
dietro per assicurarne la stabilità (perdi- Tilt the load sufficiently backwards to nach hinten, um ihre Stabilität sicherzu-
ta del carico durante la frenata) facendo ensure its stability (loss of load on stellen (Gefahr des Abstürzens der Last
però attenzione a non modificarne l’e- braking) without upsetting the balance of beim Bremsen), ohne jedoch deren
quilibrio. the load in so doing. Gleichgewicht zu beeinträchtigen.
- Se possibile (Fig. J), abbassare il cari- - Soweit möglich (Abb. J), die Last
co senza spostare il carrello elevatore. - If possible (Fig. J) lower the load absenken, ohne den Teleskopladerr zu
Alzare il braccio (1) per allontanare il without shifting the lift truck. Lift the jib bewegen. Den Teleskop anheben (1),
carico, far rientrare (2) e abbassare il um die Last frei zu fahren, den
(1) to release the load, retract (2) and
braccio (3) per portare il carico in posi- Teleskopr einfahren (2) und den
lower the jib (3) to bring the load into
zione di trasporto (Fig. L). Teleskop absenken (3), um die Last in
the transport position (Fig. L).
- Se ciò non fosse possibile, arretrare il Transportstellung zu bringen (Abb. L).
- If this is not possible, back the lift truck
carrello elevatore (Fig. K). Manovrando - Sollte dies nicht möglich sein, mit dem
molto dolcemente e con estrema pru- up. (Fig. K) Manoeuvring very gently
and carefully (See paragraph : E - VISI- Teleskoplader zurückfahren (Abb. K).
denza (Vedi paragrafo : E - VISIBILITÀ Durch sehr langsames und vorsichti-
nel capitolo : ISTRUZIONI PER LA BILITY in the chapter : HANDLING
ges Fahren (Siehe Absatz : E - SICHT
MOVIMENTAZIONE relativo alla visibi- INSTRUCTIONS for visibility of the
im Kapitel : HANDHABUNGSANWEI-
lità sul percorso), arretrare il carrello road), back up the lift truck (1) to relea-
SUNGEN für die Sicht auf dem
elevatore (1) per allontanare il carico, se the load, retract (2) and lower the jib
Fahrweg), den Teleskoplader zurück-
far rientrare (2) e abbassare il braccio (3) to bring the load into the transport
setzen (1), um die Last frei zu fahren,
(3) per portare il carico in posizione di position (Fig. L). den Teleskop einfahren (2) und den
trasporto (Fig. L). Ausleger absenken (3), um die Last in
Transportstellung zu bringen (Abb. L).
D - Posare un carico in alto su D - Laying a high load on tyres D - Ablegen einer Last auf Reifen.
pneumatici.
È tassativamente vietato depositare un Under no circumstances should you lay Sie dürfen auf keinen Fall eine Last
carico se il carrello elevatore non è in down a load if the lift truck is not a hori- ablegen, wenn der Teleskoplader nicht
piano (Vedi paragrafo : G - zontal position. (See paragraph : G - horizontal steht (Siehe Absatz : G -
HORIZONTAL POSITION OF THE LIFT HORIZONTALLAGE DES GABELSTA-
ORIZZONTALITÀ DEL CARRELLO
TRUCK in the chapter : LOAD HAND- PLERS im Kapitel : HANDHABUNG
ELEVATORE, nel capitolo : MOVIMEN- EINER LAST).
TAZIONE DI UN CARICO). LING).
J K L
24
- Avvicinare il carico in posizione di - Approach the load in the transport - Die Last in Transportposition vor den
trasporto davanti alla pila (Fig. L). position in front of the pile (Fig. L). Stapel bringen (Abb. L).
- Alzare e allungare il braccio (1) (2) fino - Lift and extend the jib (1) (2) until the - Den Teleskop heben und ausfahren (1)
load is above the pile, if necessary (2), bis die Last sich über dem Stapel
a quando il carico è al disopra della
move the lift truck forward (3) (Fig. M) befindet, falls nötig mit dem
pila, se occorre far avanzare il carrello manoeuvring very gently and carefully Teleskoplader vorfahren (3) (Abb. M),
elevatore (3) (Fig. M) manovrando dol- (See paragraph : E - VISIBILITY in the dabei sehr langsam und vorsichtig vor-
cemente e con prudenza (Vedi para- chapter : HANDLING INSTRUCTIONS gehen (Siehe Absatz : E - SICHT im
grafo : E - VISIBILITÀ nel capitolo : for visibility of the road). Apply the Kapitel : HANDHABUNGSANWEISUN-
ISTRUZIONI PER LA MOVIMENTA- parking brake and place the GEN für die Sicht auf dem Fahrweg).
ZIONE relativo alla visibilità sul percor- forward/reverse lever in neutral. Handbremse anziehen und den Hebel
- Place the load in a horizontal position des Fahrtrichtungswahlschalter in
so). Azionare il freno di stazionamento
and lay it down on the pile by lowering Neutralstellung bringen.
e mettere la leva dell'invertitore di mar- and retracting the jib (1) (2) in order to - Die Last in die Waagerechte bringen
cia in folle. position the load correctly (Fig. N). und auf den Stapel setzen, dabei durch
- Posizionare il carico orizzontalmente e - Free the forks by alternately retracting Absenken und Einfahren des
posarlo sulla pila, abbassando e rien- and lifting the jib (3) (Fig. N) or, if pos- Auslegers (1) (2) die Last richtig posi-
trando il braccio (1) (2) per posizionare sible, by reversing the lift truck (3) (See tionieren (Abb. N).
correttamente il carico (Fig. N). paragraph : E - VISIBILITY in the - Die Gabeln durch abwechselndes
chapter : HANDLING INSTRUCTIONS Einfahren und Anheben des Auslegers
- Liberare le forche, facendo alternativa-
for visibility of the road). Then bring the (3) (Abb. N) oder, falls möglich, durch
mente rientrare e alzare il braccio (3) jib into the transport position. Rückwärtsfahren des Teleskoplader (3)
(Fig. N), o se possibile, facendo indie- frei fahren (Siehe Absatz : E - SICHT
treggiare il carrello elevatore (3) (Vedi im Kapitel : HANDHABUNGSANWEI-
paragrafo : E - VISIBILITÀ nel SUNGEN für die Sicht auf dem
capitolo : ISTRUZIONI PER LA MOVI- Fahrweg). Anschließend den Teleskop
MENTAZIONE relativo alla visibilità sul in Transportstellung bringen.
percorso). Quindi portare il braccio in
posizione di trasporto.
- Inclinare le forche (1) in avanti e allun- - Tilt the carriage (1) forwards and - Den Gabelträger nach vorn neigen (1)
gare il braccio (2) inclinando contem- extend the jib (2) while simultaneously und den Teleskop ausfahren (2), dabei
crowding the carriage backwards to den Gabelträger wieder nach hinten
poraneamente le forche (3) indietro per
slip the forks under the load (Fig. O). If neigen (3) um die Gabeln unter die
inserire le forche sotto il carico (Fig.O). Last zu schieben (Abb. O). Falls nötig,
necessary, wedge the load.
Se necessario zeppare il carico. Last verkeilen.
- Always watch the load status indicator - Bei der Handhabung immer die
- Osservare sempre l'indicatore di stato
while handling a load. Lastanzeige beobachten.
di carico durante la movimentazione.
M N O
25
Quando l'indicatore di stato di carico è If the load status indicator alarm is acti- Sollte die Lastanzeige einen Alarm
in allarme, non bisogna in alcun caso: ved, do not carry out the movements anzeigen, dürfen auf keinen Fall soge-
said to be "WORSENING", which are nannte "ERSCHWERENDE"
the following : Bewegungen ausgeführt werden,
und zwar :
- Se l'indicatore di stato di carico è in - If the load status indicator alarm is - In diesem Fall dürfen nur positive
actived, carry out in all security move Bewegungen ausgeführt
allarme, effettuare i movimenti sgra-
ments in the following order (Fig. P) : werden.Bewegungen in folgender
vanti, nel seguente ordine (Fig. P) :
1 - Fully retract the jib. Reihenfolge ausführen (Abb. P) :
1 - Rientrare il braccio al massimo. 2 - If it’s necessary lift the jib 1 - Teleskop völlig einfahren.
2 -Se necesario alzare il braccio 3 - Lower the jib in order to lay the load. 2 - Teleskop absenken und die Last
3 - Abbassare il braccio in modo da 3 - Ausleger absenken und die Last
posare il carico. ablegen.
Carrello elevatore con correttore d’in- Lift truck with level corrector Gabelstapler mit neigungsausgleich.
clinazione.
- Die Neigung durch Betätigen der
- Correggere l’inclinazione, agendo sul hydraulischen Steuerung korrigieren
- Correct the slope using the hydraulic
comando idraulico e verificare l’oriz- und die Horizontallage auf dem Pegel
control and check the horizontal posi-
zontalità sulla livella prima di sollevar il prüfen (Siehe Kapitel : STEUER- UND
tion on the level before lifting the
bracio(Vedi capitolo : STRUMENTI DI BEDIENUNGSINSTRUMENTE,
CONTROLLO E DI COMANDO, nella boom(See chapter : INSTRUMENTS
AND CONTROLS in paragraph : 2 - Abschnitt : 2 - BESCHREIBUNG).
parte : 2 - DESCRIZIONE). Mit Ausnahme des transversalen
Oltre alla pendenza trasversale del ter- DESCRIPTION).
Apart from the transverse slope of the Geländegefälles, können mehrere
reno, altri parametri possono incidere Parameter die Horizontallage des
sull’orizzontalità del carrello elevatore. ground, several parameters can upset
Gabelstaplers beeinträchtigen.
• Lo stato e la pressione dei pneumatici. the horizontal position of the lift truck.
• Der Druckzustand der Bereifung.
• La stabilità del terreno. • The tyre pressures.
• Die Stabilität des Bodens.
• L’equilibrio del carico. • The stability of the ground.
• Das Gleichgewicht der Last.
• Il vento forte o la tempesta. • The balance of the load. • Starker Wind oder Sturm.
• Strong wind or stormy conditions.
Prima di ogni movimentazione, control- Before any handling work, check the Vor den Einsatz des Teleskoplader sind
lare le condizioni sopraelencate e verifi- points above and ensure that the lift die oben genannten Punkte zu prüfen.
care che il carrello elevatore sia perfet- truck is completely horizontal. Sicherstellen, dass der Gabelstapler
tamente orizzontale. (See bubble level) perfekt horizontal steht.
(Controllare sulla livella a bolla)
26
- Leggere con attenzione e comprende- - Read the operator's manual carefully - Die Bedienungsanleitung sorgfältig
re il manuale d'istruzioni. and ensure you understand it. lesen und sicherstellen, daß die Inhalte
- Spegnere il motore termico prima di - Stop the I.C. engine, when an und Vorgehensweisen verstanden wur-
ogni intervento sul carrello elevatore. intervention is necessary. den. .
- Indossare abbigliamento adeguato alle - Wear clothes suitable for the mainte- - Vor jedem Eingriff an dem
operazioni di manutenzione del carrello nance of the lift truck, avoid wearing Teleskoplader den Motor abstellen.
elevatore, evitando i gioielli e gli indu- jewellery and loose clothes. Tie and - Für die Wartung des Teleskoplader
menti troppo larghi. Se occorre, legare protect your hair, if necessary. geeignete Kleidung tragen, Schmuck
e proteggere i capelli. - Ensure the area is sufficiently ventila- und weite Kleidung vermeiden.
- Assicurarsi che il locale sia ted before starting the lift truck. Gegebenenfalls Haare hochbinden und
sufficientemente ventilato prima di schützen.
mettere in moto il carrello elevatore. - Vor dem Starten des Teleskopladers für
ausreichende Belüftung sorgen.
Porre particolare attenzione allo smalti- Make sure that the disposal of process Darauf achten, daß die Entsorgung der
mento dei materiali di consumo e dei materials and of spare parts is Verbrauchsstoffe und der Altteile sicher
pezzi usati, verificando che venga effet- carried out in total safety und umweltfreundlich erfolgt.
tuato nella massima sicurezza and in a ecological way.
e in modo ecologico.
- Effettuare le riparazioni necessarie, - Carry out all repairs immediately, even - Notwendige Reparaturen, selbst kleine,
anche le minori, immediatamente. if the repairs concerned are minor. sofort durchführen.
- Riparare ogni perdita, anche minima, - Repair all leaks immediately, even if - Jede Leckage, selbst kleinere, sofort
immediatamente. the leak concerned is minor. reparieren.
- Non cercare di allentare i raccordi, i - Do not attempt to loosen unions, hoses - Versuchen Sie niemals, Hydraulische
flessibili o un componente idraulico, or any hydraulic component with the Verbindungen,Schläuche,oder
con il circuito in pressione. circuit under pressure. Hydraulikkomponenten die unter Druck
stejhen zu öffnen.
La modifica della regolazione e lo The handling and removal of the balan- Jede Einstellungsänderung oder der
cing valves or safety valves which may Ausbau der Ausgleichventile oder der
smontaggio delle valvole di equilibratura
be fitted to the cylinders of your lift truck Sicherheitventile, mit denen die Zylinder
che o delle valvole di sicurezza che, a
can be dangerous. A balancing valve des Teleskoplader ausgestattet sein
volte, equipaggiano i martinetti del car-
must only be removed when the cylin- können, kann sich als gefährlich
rello elevatore, possono rivelarsi perico-
der concerned is at rest and the hydrau- erweisen. Ein Ausgleichventil darf nur
losi. Una valvola di equilibratura può
lic circuit is depressurised. ausgebaut werden, wenn der
essere smontata solo con il martinetto
This operation can only be carried entsprechende Zylinder in Ruhestellung
interessato a riposo e con il circuito
out by authorised staff. und der Hydraulikkreis drucklos ist.
idraulico senzapressione.
Dieser Eingriff darf nur von
Tale operazione può essere effettua-
authorisiertem Personal durch-
ta solo da personale autorizzato.
geführt
werden.
27
- Non fumare o avvicinarsi al carrello - Do not smoke or approach the lift truck - Nicht rauchen oder sich mit einer offe-
elevatore con fiamme libere quando il with a flame, when the fuel tank is nen Flamme dem Teleskoplader
serbatoio del combustibile è aperto o open or is being filled. nähern, wenn dessen Kraftstofftank
in fase di riempimento. - Take care not to burn yourself offen ist oder gefüllt wird.
- Attenzione ai rischi di ustioni (Exhaust, radiator, I.C. engine, etc.). - Vorsicht, Verbrennungsgefahr (Auspuff,
(Scappamento, radiatore, motore - Disconnect the negative cable terminal Kühler, Verbrennungsmotor, usw.).
termico, ecc.). (-) from the top of the battery before - Vor Arbeiten am Stromkreis oder am
- Scollegare il capocorda negativo (-) working on the electrical circuit or on Teleskoplader(Z. B. Schweißen) die
dalla batteria prima di lavorare sull'im- the lift truck (e.g. : Welding). Minusklemme (-) der Batterie abklem-
pianto elettrico o sul carrello elevatore - Do not drop metallic items on the bat- men.
(Es. : Saldatura). tery. - Keine Metallteile auf die Batterie legen.
- Non posare pezzi metallici sulla - When carrying out electric welding - Zur Durchführung von
batteria. work on the lift truck, connect the Elektroschweißarbeiten am
- Per effettuare una saldatura elettrica negative cable from the equipment Teleskoplader, die Minusklemme des
sul carrello elevatore, porre la pinza directly to the part being welded, so as Schweißgerätes direkt an das zu
del cavo negativo della saldatrice diret- to avoid high tension current passing schweißende Teil legen, damit der
tamente sul pezzo da saldare, onde through the alternator. Strom nicht durch die Lichtmaschine
evitare che la corrente molto forte fließt.
attraversi l'alternatore.
- La manutenzione e il mantenimento - The maintenance and the keeping in - Der Teleskoplader muß zwangsläufig
dello stato di conformità del carrello compliance of the lift truck are compul- instand und in konformem Zustand
elevatore sono obbligatori. sory. gehalten werden.
- Effettuare la manutenzione giornaliera - Carry out daily maintenance (See - Tägliche Instandhaltung durchführen
(Vedi capitolo : A - OGNI GIORNO O chapter : A - DAILY OR EVERY 10 (Siehe Kapitel : A - TÄGLICH ODER
OGNI 10 ORE DI FUNZIONAMENTO HOURS SERVICE in paragraph : 3 - ALLE 10 BETRIEBSSTUNDEN,
nella parte : 3 - MANUTENZIONE). MAINTENANCE). Abschnitt : 3 - WARTUNG).
- Non far funzionare il motore termico - Do not run the I.C. engine without air - Den Verbrennungsmotor nicht ohne
senza il filtro dell'aria o con perdite filter, or with oil, water or fuel leaks. Luftfilter oder mit Öl-, Wasser- oder
d'olio, d'acqua o di combustibile. Kraftstoffleckagen in Betrieb nehmen.
Aspettare il raffreddamento del Wait for the I. C engine to cool before Vor dem Entfernen des
motore termico prima di rimuovere removing the radiator cap. Kühlerverschlusses sicherstellen, daß
il tappo del radiatore. der Motor abgekühlt ist.
VERBRENNUNGSGEFAHR
- Sostituire le cartucce dei filtri (Vedi - Change the filter cartridges (See ser- - Filterpatronen auswechseln (Siehe
periodicità di sostituzione nel capitolo vicing schedules in chapter : FIL- Austauschhäufigkeit im Kapitel : FILTE-
ELEMENTI FILTRANTI E CINGHIE TERS CARTRIDGES AND BELTS in RELEMENTE UND KEILRIEMEN,
nella parte : 3 - MANUTENZIONE). paragraph : 3 - MAINTENANCE). Abschnitt : 3 - WARTUNG).
- Utilizzare i lubrificanti raccomandati - Use the recommended lubricants - Nur empfohlenen Schmiermittel einset-
(Non utilizzare mai lubrificanti usati). (Never use contaminated lubricants). zen (Auf keinen Fall gebrauchte
- Non riempire il serbatoio del - Do not fill the fuel tank when the I.C. Schmiermittel verwenden).
combustibile quando il motore termico engine is running. - Den Kraftstofftank nicht bei laufendem
è in funzione. - Only fill up the fuel tank in areas Motor befüllen.
- Effettuare il pieno di combustibile solo specified for this purpose. - Den Teleskoplader nur an den dafür
negli appositi spazi previsti a tale vorgesehenen Stellen auftanken.
scopo.
28
- Pulire il carrello elevatore, o al meno la - Clean the lift truck or at least the area - Den Teleskoplader oder zumindest den
parte interessata, prima di ogni concerned before any intervention. betroffenen Bereich vor jedem Eingriff
intervento. - Remember to close the door and the reinigen.
- Non dimenticare di chiudere la porta e rear - Denken Sie daran, die Tür und das
il lunotto posteriore della cabina. window of the cab. hintere Fenster des Führerstands zu
- Durante il lavaggio, evitare di bagnare - During washing, avoid the articulations schließen.
le articolazioni, i componenti e and electrical components and -, Gelenke und elektrische
collegamenti elettrici. connections. Komponenten und Anschlüsse
vor dem Reinigen abdecken..
Se necessario proteggere dall'acqua, If necessary, protect against penetration Falls nötig Komponenten, die beschä-
dal vapore o dai prodotti detergenti, i of water, steam or cleaning agents, digt werden könnten, insbesondere
componenti che rischiano di venire dan- components susceptible of being dama- elektrische Komponenten und
neggiati, in particolare i componenti e i ged, particularly electrical components Anschlüsse und die Einspritzpumpe, vor
collegamenti elettrici e la pompa and connections and the injection dem Eindringen von Wasser, Dampf
d'iniezione. pump. oder Reinigungsmitteln schützen.
- Pulire il carrello elevatore da ogni trac- - Clean the lift truck of any fuel, oil or - Jede Spur von Kraftstoff, Öl oder Fett
cia di combustibile, d'olio o di grasso. grease trace. vom Gabelstapler entfernen.
Per ogni intervento che non rientri For any intervention other than Für jeden anderen Eingriff als die
nella manutenzione ordinaria, rivol- regular maintenance, consult your normale Instandhaltung fragen Sie
getevi al vostro agente o conces- dealer. Ihren Vertreter oder
sionario. Vertragshändler.
29
PRIMA DI AVVIARE UN CARRELLO BEFORE STARTING UP A NEW LIFT VOR DER INBETRIEBNAHME EINES
NUOVO TRUCK NEUEN TELESKOPLADER
Introduzione. Einleitung.
Introduction. - Unsere Teleskoplader wurden dahin-
- I nostri carrelli elevatori sono stati pro- gehend entwickelt, dem Fahrer eine
gettati per offrire al conduttore la mas- - Our lift trucks have been designed for einfache Bedienung und eine so einfa-
sima semplicità di manovra e una easy handling by the operator and ch wie möglich gestaltete Wartung zu
grande facilità di manutenzione. maximum ease of maintenance for the bieten.
- Tuttavia, prima del primo avviamento mechanic. - Vor der ersten Inbetriebnahme des
del carrello elevatore, l'utilizzatore - However, before commencing to ope- Teleskoplader muß der Benutzer jedo-
dovrà leggere con attenzione e com- rate the lift truck, the user should care- ch die verschiedenen Kapitel dieser
Bedienungsanleitung sorgfältig lesen
prendere il presente manuale, redatto fully read and understand the various und sicherstellen, daß diedort besch-
per rispondere a tutti i problemi di chapters of this manual which has riebenen Inhalte und Vorgehensweisen
guida e di manutenzione. Seguendo le been provided to solve driving and verstanden wurden. Die bedienungsan-
istruzioni, l'utilizzatore sarà in grado di maintenance problems. By following leitung beinhaltet alle Informationen
sfruttare al meglio le prestazioni offerte these instructions the user will be able eventueller Fahr- und
dal carrello elevatore. to take full advantage of the versatility Wartungsprobleme . Wenn diese
- L'utilizzatore dovrà, prima di utilizzare il of this lift truck. Anweisungen befolgt wird, kann der
carrello elevatore, conoscere le funzio- - The operator must familiarize himself Benutzer die Kapazitäten des
Teleskoplader voll ausnutzen.
ni e posizioni dei diversi strumenti di with the positions and functions of all - Der Benutzer muß sich vor dem
controllo e di comando. the controls and instruments before Einsatz des Teleskoplader mit der
operating the lift truck. Lage und der Funktion der verschiede-
nen Steuer- und
Bedieninstrumente vertraut machen.
Non avviare mai un nuovo carrello ele- Do not attempt to start a new lift truck
vatore, prima di aver effettuato i before the following checks have been Vor dem Starten Ihres neuen
seguenti controlli : carried out : Teleskoplader sollten folgende Punkte
überprüft werden:
Lubrication.
Ingrassaggio. Schmierung.
- Check that all the correct grades of oils
- Controllare i vari punti d'ingrassaggio e and greases that are required are avai- - Die verschiedenen Schmierpunkte und
Flüssigkeitsstände überprüfen, siehe
i vari livelli, vedi capitolo : lable ; see chapter : SERVICING Kapitel : WARTUNGSINTERVALLE,
PERIODICITÀ DELLA MANUTENZIO- SCHEDULE in paragraph : 3 - MAIN- Abschnitt : 3 - WARTUNG, und gege-
NE nella parte : 3 - MANUTENZIONE TENANCE and top up if necessary. benenfalls vervollständigen.
e procedere alle eventuali aggiunte.
Il pieno di lubrificanti è già stato effettua- For operation under average climatic Die Schmiermittel werden im Werk für
to in fabbrica, utilizzando lubrificanti per conditions, i.e. : between -15 °C and durchschnittliche Klimabedingungen ein-
+ 35 °C, correct levels of lubricants in all gefüllt, d. h. -15°C bis + 35°C. Für härte-
condizioni climatiche d'uso medie, ossia re Einsätze muß der Teleskoplader vor
da -15°C a + 35°C. Per un utilizzo in the circuits are checked in production.
For operation under more severe clima- der Inbetriebnahme entleert und mit für
condizioni estreme occorre, prima del- die Umgebungstemperaturen geeigne-
l'avviamento, svuotare e rifare i pieni, tic conditions, before starting up, it is ten Schmiermitteln gefüllt werden. Dies
utilizzando i lubrificanti adatti a tali tem- necessary to drain all the circuits, then gilt auch für das Kühlmittel (Erkundigen
perature. Lo stesso vale per il liquido di ensure correct levels of lubricants using Sie sich gegebenenfalls bei Ihrem oder
raffreddamento (Per maggiori informa- lubricants properly suited to the relevant Vertragshändler).
zioni, rivolgetevi al vostro agente o con- ambient temperatures. It is the same for
cessionario). the cooling liquid (Contact your dealer
for information, if necessary).
- Accertarsi che il filtro dell'aria sia in - Ensure that the air filter is undamaged - Überzeugen Sie sich davon, daß sich
buono stato e non sia intasato. and not blocked. der Luftfilter in einem gutem, sauberen
- Stringere i bloccaggi se occorre. - Tighten the fastening devices if und einwandfreiem Zustand befindet.
necessary.
Non utilizzare mai il carrello elevatore Never run the I.C. engine with the air fil- Niemals den Teleskoplader ohne Luftfilter
senza il filtro dell'aria o con un filtro del- ter removed or damaged. oder mit einem beschädigten Luftfilter
l'aria danneggiato. einsetzen.
- Non mettere mai in moto il carrello - Always check the cooling liquid level - Den Teleskoplader nie in Betrieb
elevatore senza avere preventivamente before starting up the lift truck. nehmen, wenn man nicht vorher den
controllato il livello del liquido di Stand der Kühlflüssigkeit geprüft hat.
raffreddamento.
30
- Verificare che non ci siano perdite o - Check by a visual examination that - Überzeugen Sie sich durch eine
trasudazioni d'olio sui collegamenti, there are no leaks or oil oozing in the Sichtkontrolle von de Dichtheit des
flessibili, tubi e raccordi. Se occorre, hoses, connections and unions. If Bremssystems
ristringere o controllare i collegamenti necessary, tighten or repair the defecti- - Ebenfalls den Ölstand im Tank über-
difettosi. ve connections. prüfen.
- Controllare anche il livello dell'olio nel - Also check the oil level in the tank.
serbatoio.
Pneumatici.
Tyres. Reifen.
- Accertarsi che i bulloni di fissaggio
- Make sure that the wheel nuts are - Überprüfen Sie die Radmuttern auf
delle ruote siano stretti a fondo (Vedi
correctly tightened (See chapter : A - festen Sitz.
capitolo : A - OGNI GIORNO O OGNI
DAILY OR EVERY 10 HOURS SERVI- (Siehe Kapitel : A - TÄGLICH ODER
10 ORE DI FUNZIONAMENTO nella
CE in paragraph : 3 - MAINTENAN- ALLE 10 BETRIEBSSTUNDEN,
parte : 3 - MANUTENZIONE) e control-
CE) and that the tyre pressures are Abschnitt : 3 - WARTUNG).
lare la pressione dei pneumatici (Vedi
correct (See chapter : CHARACTERI- Reifendruck prüfen (Siehe Kapitel :
capitolo : CARATTERISTICHE nella
STICS in paragraph : 2 - DESCRIP- TECHNISCHE DATEN, Abschnitt : 2 -
parte : 2 - DESCRIZIONE).
TION). BESCHREIBUNG).
- Verificare il livello e la densità - Check the level and the density of the - Stand und Dichte des Elektrolyts in der
dell'elettrolito nella batteria (Vedi electrolyte in the battery (See chapter : Batterie überprüfen (Siehe Kapitel : B -
capitolo : B - OGNI 50 ORE DI B ALLE 50 BETRIEBSSTUNDEN,
FUNZIONAMENTO nella parte : 3 - - EVERY 50 HOURS SERVICE in Abschnitt : 3 - WARTUNG).
MANUTENZIONE). paragraph : 3 - MAINTENANCE). - Die verschiedenen Elemente der
- Controllare i vari componenti - Check the components of the electrical Elektrik sowie deren Anschlüsse und
dell'impianto elettrico, i loro system, the connections and fastening Befestigung überprüfen.
collegamenti e contatti. devices.
31
UTILIZZO DEL DISPOSITIVO DI ROTAZIONE USE OF THE SLEWING DEVICE BENUTZUNG DER ROTATIONSVORRICH-
TUNG
Il carrello MRT 1432 - 1635 è dotato del MRT 1432 - 1635 lift truck is equipped
dispositivo di rotazione idraulica a 360° with a hydraulic slewing device able to Der Teleskoplader MRT 1432 - 1635 ist mit
o 400°. turn through 360° or 400°. einer hydraulischen Rotationsvorrichtung
von durchgehend 360° / 400°.
Durante la rotazione per garantire During the slewing action, the automatic Um dem Teleskoplader eine bessere
migliore stabilità e portata al carrello, rear axle locking device activates after Standsicherheit und eine höhere
dopo aver superato i 15° di rotazione more than a 15° turn in order to ensure Tragefähigkeit zu verleihen, tritt bei der
entra in funzione il dispositivo automati- greater stability and carrying capacity. Rotation nach 15° Verdrehung eine
co di blocco dell' assale posteriore; The driver must, however, take the automatische Vorrichtung in Funktion,
nonostante tutto l'operatore per l' utilizzo utmost care and strictly comply with the die die Hinterachse blockiert. Trotz die-
di questo dispositivo dovrà fare attenzio- following instructions when using this ser automatischen Sicherung muß der
ne e seguire le seguenti raccomandazio- device: Bediener bei Verwendung der
ni: Rotationsvorrichtung die folgenden
Vorsichtsmaßnahmen beachten:
- Verificare che il perno di blocco rota- - Check that the slewing lock pin is not - sicherstellen, daß der
zione non sia inserito (vedere punti 3 1 e engaged (see points 3 1 and 1 3 of the Rotationsperrzapfen nicht eingerastet ist
1 3 del capitolo "STRUMENTI DI CON- “INSTRUMENTS AND CONTROLS” (vgl. Punkte "33 1 " und "1
1 3 " des Kapitels
TROLLO E DI COMANDO") chapter). “KONTROLL- UND BEDIENUNGSVOR-
RICHTUNGEN”).
- Attenersi ai dati indicati sui diagrammi - Comply with the curves on the load - Die Daten beachten, die in den
di carico. chart diagrams Lastdiagrammen stehen.
- Sicherstellen, daß die Hauben und die
- Verificare che i cofani e la portiera infe- - Check that the hoods and lower part of untere Kabinentür geschlossen sind.
riore siano chiusi. the door are closed. - Während der Rotation sicherstellen,
daß der Drehturm nicht gegen
- Verificare durante la rotazione che la - When the turret slews, check that it Hindernisse in unmittelbarer Nähe stößt.
torretta non urti ostacoli nelle immediate cannot hit against obstructions in the -Keine langen Fahrbewegungen ausfüh-
vicinanze. near vicinity. ren, weder mit noch ohne Last, wenn
der Drehturm nicht auf die
- Non eseguire lunghi spostamenti con e - Never drive for long distances with or Fahrzeugachse ausgerichtet ist.
senza carico se la torretta non è allinea- without a load, unless the turret has
ta. been aligned.
Strassenverkehr:
Road travel :
Circolazione stradale Während der Teilnahme am
Per la circolazione su strada la rotazione The hydraulic slewing mechanism must Straßenverkehr muß die hydraulische
idraulica deve essere bloccata , il carrel- be locked during road travel. The truck Rotationsvorrichtung verriegelt sein. Der
lo è provvisto di un dispositivo di bloc- is equipped with a locking device. Teleskoplader ist mit einer
caggio. Sperrvorrichtung versehen.
Consult points 1 3 and 3 1 of the
Per l' inserimento del dispositivo vedere “INSTRUMENTS AND CONTROLS” Die Einschaltung dieser Vorrichtung ist
punti 1 3 , e 3 1 del capitolo "STRUMEN- chapter when engaging this device. in den Punkten "1
1 3 "und "3
3 1 " des
TI DI CONTROLLO E DI COMANDO". Kapitels “KONTROLL- UND BEDIE-
NUNGSVORRICHTUNGEN” beschrie-
ben.
UTILIZZO DEGLI STABILIZZATORI USE OF THE OUTRIGGERS BESTIMMUNGEN FÜR DIE BENUTZUNG
DER STÜTZFÜSSE
Il carrello MRT 1432 - 1635 è dotato di 4 Lift truck MRT 1432 - 1635 has 4 outrig- Der Teleskoplader MRT 1432 - 1635 ist
stabilizzatori con comando indipendente, gers with independent control able to mit 4 einzeln zu bet tigenden
permettono un poligono di appoggio di 4 achieve a polygon base of 4 meter of Scherenst tzen versehen, die eine
metri di lunghezza e 3,8 metri di lenght and 3.8 of widht thus stabilizing Standfl che von 4 Meter Seitenl nge
larghezza dando così alla macchina the truck during the work phases. und 3,8 Meterbreite verleihen und die
stabilità e sicurezza sul lavoro. Maschine dadurch standfest und sicher
machen.
32
1 2
3,8 mt
4 mt
3,8 mt
4 mt
33
Specifiche MRT 1432 Specifications MRT 1432 Technische daten MRT 1432
Massima capacità nominale con equi- Max rated capacity with Maximale tragfähigkeit
paggiamento STD carriage Standardausrüstung:
STD:Forche . . . . . . . .3200 Kg and forks . . . . . . . . . .3200 Kg Gabelzinken . . . . . . . .3200 Kg
Carico massimo esercitato su Maximum weight applied to each Max. Belastung auf jede
ciascun stabilizzatore 6500 daN outrigger 6500 daN Abstützung 6500 daN
Massima capacità nominale con equi- Max rated capacity with Maximale tragfähigkeit
paggiamento STD carriage Standardausrüstung:
STD:Forche . . . . . . . .3500 Kg and forks . . . . . . . . . .3500 Kg Gabelzinken . . . . . . . .3500 Kg
Carico massimo esercitato su Maximum weight applied to each Max. Belastung auf jede
ciascun stabilizzatore 8050 daN outrigger 8050 daN Abstützung 8050 daN
Potenza acustica . . . .LwA 104 dB Acustic power . . . . . .LwA 104 dB Akustische Leistung . .LwA 104 dB
(secondo EN 2000/14/CE) (in accordance with EN 2000/14/CE) (nach EN 2000/14/CE)
A 1200 mm
J
I
A1 125 mm
A2 1320 mm
A3
A3 45 mm
H
Z Y
B 290 mm E F G
C 5060 mm D
D 4350 mm A B C
E 1015 mm
F 2320 mm V
G 1015 mm
H 340 mm
I 2365 mm
J 2970 mm
K 2040 mm
L 1930 mm
M 2390 mm
N 3400 mm
P
L
O 3800 mm M
P 160 mm N
O
Q 3900 mm
R 3410 mm
S 4000 mm
T 3600 mm
U 5250 mm
Q
V 950 mm R
T
Y 12°
Z 105°
A2
A1
A 1200 mm
J
I
A1 125 mm
A2 1320 mm
A3
H
A3 45 mm
Z Y
B 290 mm E F G
D
C 6075 mm A B C
D 4350 mm
E 1015 mm
F 2320 mm V
G 1015 mm
H 340 mm
I 2375 mm
J 2970 mm
K 2485 mm
L 1930 mm
M 2390 mm
N 3400 mm L P
O 3800 mm M
P 160 mm N
Q 3900 mm O
R 3410 mm
S 4000 mm
T 3600 mm
U 5520 mm
V 950 mm Q
T
Y 12°
R
Z 105°
A2
A1
I diagrammi di portata sono validi The load capacity diagrams are Diese Traglastdiagramme gelten
solo con il sistema di sicurezza only valid with the safety system nur bei korrekt eingestellten
regolarmente inserito. properly activated. Sicherheitssystem.
Forks
500 mm
3200 13,8 m Forks
500 mm
3200 13,6 m
MRT 1432 MSeries
690789 690790
9
2
2 IT EN
MRT 1432 MSeries
DE
13,6 m
690791
pos. A
1800
Kg
MRT 1432
Forks 500 mm
10
Forks
500 mm
3500 15,8 m Forks
500 mm
3200 15,6 m
MRT 1635 MSeries
690905 690906
11
2
2 IT EN
MRT 1635 MSeries
DE
690907
14 m
pos. A
1800
Kg
MRT 1635
Forks 500 mm
12
Fari anteriori
Front lights
Frontlicht
Fari posteriori
Rear lights
Rücklicht
13
41
8 4
44
3
43
5
47
15 36
15
16
6 46
7
1 11
12
17 19 35 34
15.3
13
17 18 9 33
31 32 10.1 10 22 20
30 21
15.4
23 25 27 28
14
15
Qualunque sia l’esperienza dell’opera- However experienced the driver may be Es wird empholen, sich mit der
tore in questo settore, egli dovrà in this field, he must become fully fami- Handhabung, den Bedienelementen und
imparare l’ubicazione e la funzione di liar with the location and function of all der Anordnung aller Schalter und Hebel
tutti gli strumenti di bordo e dei instruments and controls before opera- sowie deren Funktion vor
comandi, prima di mettere in funzione ting the lift truck. Inbetriebnahme des Teleskopladers ver-
il carrello elevatore. Check all instruments immediately after traut zu machen.
Occorre controllare tutti gli strumenti having started the truck when the engine - Nach dem Starten des Motors und
di bordo immediatamente dopo la has warmed up and at regular intervals anschließend in regelmäßigen
messa in marcia quando il motore é during use. This will enable the driver to Abständen sollten die Kontrollanzeigen
caldo e ad intervalli regolari durante immediately identify any faults and to geprüftwerden, um einen eventuellen
l’uso, in modo da rilevare subito even- proceed with prompt remedies. If an defekt frühzeitig zuerkennen.
tuali anomalie e porvi rimedio senza instrument fails to give the right indica- - Sollte eine Kontrollanzeige keine kor-
indugio. Se uno strumento non forni- tion, switch off the engine and take the rekten Werte anzeigen, den
sce indicazioni corrette, spegnere il necessary measures in order to restore Teleskoplader abstellen und sofort die
motore e prendere immediatamente i correct operation. nötigen Maßnahmen veranlassen um
provvedimenti necessari per ristabilire einen fehlerfreien Einsatz zu gewährlei-
il corretto funzionamento. sten.
L’utilizzo del carrello elevatore senza Use of the truck without due regard of Der Einsatz des Teleskopladers ohne
tener conto di queste raccomandazio- these recommendations could be Beachtung dieser Warnhinweise kann
ni può avere conseguenze pericolose. dangerous. zu erheblichen Beschädigungen führen.
16
Tirare la leva A (Fig.1) verso l'alto. Hebel A (ABB. 1) nach oben ziehen.
Pull the locking lever A (Fig.1) upwards. Sitz in Abhängigkeit von den
Muovere avanti o indietro,il sedile, Slide the seat to the desired position. Armlehnen nach vorne bzw. hinten
nel modo desiderato,in funzione dei in die gewünschte Position bewe-
Release the lever and ensure that it
braccioli. returns to the locked position. gen.
Rilasciare la leva ed assicurarsi che Hebel loslassen und darauf achten,
ritorni nella posizione di bloccaggio. dass er in der Verriegelung einra-
stet.
Regolazione avanti-indietro del sedile Forward-back seat adjustment Einstellung des Fahrersitz
Tirare la leva B verso l'alto (FIG. 1). Pull the locking lever B upwards (Fig. 1). Die Verriegelungl B nach oben ziehen
Posizionare il sedile nel modo desi- Slide the seat to the desired position. (ABB. 1).
derato. Release the lever and ensure that it Den Sitz in die gewünschte Position ver-
Rilasciare la leva ed assicurarsi che returns to the locked position. schieben.
ritorni nella posizione di bloccaggio. Die Verriegelung wieder einrasten las-
sen.
Gewichtseinstellung
Regolazione della sospensione Adjusting the seat according to
del sedile in funzione del peso the driver’s weight
Die Sitzfederung kann auf das
In funzione del peso dell'operatore The height of the seat suspensions can Gewicht des jeweiligen Fahrers ein-
si può variare l'escursione della be adjusted according to the driver’s gestellt werden.
sospensione del sedile. weight. Dafür Handrad E (ABB. 1) so lange
Per compiere questa operazione To make this function use knob E(Fig.1) drehen, bis das Gewicht des jeweili-
agire sul pomello E (Fig. 1) sce- choosing the required valve. gen Fahrers angezeigt wird.
gliendo il valore desiderato.
C
A
17
A - Spia rossa di pressione olio A - Red warning light for engine oil A - Rote Kontrollleuchte
motore termico (Fig.2) pressure (Fig.2) Motoröldruck (ABB.2)
Questa spia si accende contemporanea-
mente all’accensione del contatto elettri- This warning lights when the ignition is Diese Kontrollleuchte wird bei einschal-
co sul carrello elevatore e deve spe- switched on and should go out when the ten der Zündung aktiviert. Nach dem
gnersi dopo la messa in moto del moto- engine is running. If this warning light Anspringen des Motors muß diese
re termico. Se la spia si accende duran- should come on when operating the Kontrollleuchte erlöschen.
te il funzionamento del carrello, spegne- forklift switch off the engine immediately Sollte diese Kontrollleuchte während
re immediatamente il motore termico e and investigate the cause (check the oil des Einsatz des Teleskopladers aufleu-
cercare la causa (controllare il livello level in the engine sump). chten, sofort den Motor abstellen und
dell’olio nel carter del motore). die Ursache ermitteln.
Quando il carrello elevatore lavora nor- When the fork-lift truck is operating Diese Kontrollleuchte wird aktiviert,
malmente, la spia dell’indicatore rimane under normal conditions, the indicator wenn die Wassertemperatur 95°C oder
spenta. Se la temperatura raggiunge i warning light remains off. If the tempera- mehr beträgt. Sollte diese
95° C la spia si accende; spegnere subi- ture reaches 95 °C, the warning light Kontrollleuchte während des Einsatz
to il motore termico e cercare l’origine turns on, immediately turn off the engine des Teleskopladers aufleuchten, sofort
dell’inconveniente nel circuito di raffred- and troubleshoot the cause in the coo- den Motor abstellen und die Ursache
damento. ling circuit. ermitteln.
L M A B C D
E F G H I
2
18
D - Spia rossa indicatore D - Red warning light for air filter D - Rote Kontrollleuchte Luft Luft filter
intasamento
intasamento filtro aria ( F i g . 2 ) blocked indicator ( F i g . 2 ) ver stopf
stopf t ( A B B . 2 )
Questa spia serve a segnare lo stato This warning light is used to indicate the Diese Kontrolleuchte zeigt den Zustand
della cartuccia del filtro: se questa é condition of the filter cartridge: if it is des Filtereinsatzes an: ist er verstopft
incrostata o danneggiata la spia si blocked or dameged. The warning light oder beschädigt, leuchtet die
accende (per la sostituzione della car- comes on (to replace the cartridge, Kontrollleuchte auf (für den Wechsel des
tuccia, riferirsi al capitolo “Lubrificanti”). refer to the chapter “Filters and belts”). Filtereinsatzes, siehe Kap. “Öle/Fette -
Flüssigkeiten - Treibstoff - Filter”).
E - Spia
Spia rossa di eccitazione
eccitazione E - Red warning light for alternator E - Ladekontrollleuchte (ABB. 2)
alternatore ( F i g . 2 ) exitation
exitation ( F i g . 2 )
Questa spia si accende all’inserimento This warning light comes on when the Diese Kontrollleuchte wird aktiviert,
del contatto elettrico sul carrello eleva- ignition is switchted on and should go wenn die Zündung eingeschaltet wird.
tore e deve spegnersi dopo la messa in out when the engine is running. If the Sollte diese Kontrollleuchte während
moto del motore termico. Se la spia si warning light should come on when the des Einsatz des Teleskopladers aufleu-
accende durante il funzionamento del engine is running stop the engine chten, sofort den Motor abstellen und
carrello, spegnere immediatamente il immediately, and check the alternator die Ursache ermitteln.
motore termico e verificare sia il circuito belt and electrical circuit.
elettrico sia la cinghia alternatore.
G - Spia verde indicatori di G - G reen warning light for direction G - Blaue Kontrolleuchte Fernlichter
direzione ( F i g . 2 ) indicators ( F i g . 2 ) (ABB. 2)
Questa spia si accende contempora- This warning light turns on simultaneou- Diese Kontrollampe leuchtet gleichzeitig
neamente agli indicatori di direzione e sly with the direction indicators and indi- mit der Betätigung der
ne indica il corretto funzionamento. cates that they are operating correctly. Fahrtrichtungsanzeiger auf und zeigt
deren korrekten Betrieb an.
H - Spia
Spia blu abbaglianti ( F i g . 2 ) H - Blue warning light for main beams H - Blaue Kontrolleuchte Fernlichter
lights
lights (Fig. 2) (ABB.2)
Questa spia si accende quando vengo- Diese Kontrollampe leuchtet auf, wenn
no accesi gli abbaglianti. This warning light comes on when the die Fernlichter eingeschaltet sind.
main beam lights are turned on.
L - Indicatore contaore
contaore ( F i g . 2 ) L - Hourmeter ( F i g . 2 ) L -Betriebsstundenzähler (ABB.2)
Indica il numero di ore di funzionamento This indicates the number of hours the Zeigt die Anzahl der Betriebsstunden
del carrello elevatore. Le ore appaiono forklift truck has been used. The hours des Teleskopladers an. Die Skala gibt
sul quadrante fino ai multipli di mille. are shown up to multiples of the thou- die Betriebsstunden in
sand. Tausenderschritten an.
Mostra la quantità di “gasolio” disponibi- Indicates the quantity of diesel available Zeigt die im Kraftstoffbehälter vorhande-
le nel serbatoio. La riserva segnalata in the tank. The reserve corresponds to ne Restmenge an Dieselkraftstoff an.
corrisponde circa ad 1 ora di lavoro. approximately 1 hours work. Die angegebene Reserve reicht für ca. 1
Betriebsstunde.
Girando la chiave d’avviamento fino al When the ignition key is turned to the Durch Drehen des Zündschlüssels bis
primo scatto (con il motore spento) first position (with the engine off) a zum ersten Einrasten (bei ausgeschalte-
viene eseguito un “Check” tutte le spie “check” is performed, all the lamps turn tem Motor) werden alle Kontrolleuchten
si accendono e un avvisatore acustico on and a buzzer is activated. Everything “gecheckt” und ein Signalton ertönt;
entra in funzione; tutto ritorna normale returns to normal only after the engine nach Einschalten des “Diesel”- Motors
solo dopo l’accensione del motore termi- has been turned on. kehrt alles wieder in den Normalzustand
co. zurück.
19
0 1
1 0
2 2
3 A B C D H
20
Il commutatore controlla l’accensio- The switch controls the lights and the Der Multifunktionsschalter dient zum
ne delle luci, gli indicatori di direzio-
ne e la segnalazione acustica. horn and turn indicator lights. Turn the Ein-/Ausschalten der Beleuchtung, der
Ruotando la manopola di uno scatto knob one position to switch on the front Blinker und des Horns.
si accendono le luci di posizione and rear parking lights. A green warning In der Position 1 wird das Standlicht ein-
anteriori e posteriori e si illumina la geschaltet.
spia verde sul cruscotto. Girando di light on the control panel will come on. Gleichzeitig leuchtet die grüne
un altro scatto si accendono le luci Turn the knob to the second position to Kontrolleuchte auf dem Armaturenbrettauf.
anabbaglianti, tirando la leva verso switch on the headlights. Pull the lever Dreht man den Schalter eine Position
l’alto è possibile lampeggiare e pre-
mendo la leva verso il basso è pos- upwards to switch on the main beam. To weiter, wird das Abblendlicht eingeschal-
sibile accendere i fari abbaglianti. tet. Durch Ziehen des Hebel nach oben,
operate the turn signals, just push lever wird zusätzlich das Fernlicht eingeschaltet.
Per far funzionare gli indicatori di dire-
zione è sufficiente spingere la leva in forward or rearword Um die Blinkleuchten einzuschalten,
avanti o indietro in base alla direzione according to the desired direction. den Hebel “4” in die
voluta. Push forword to turn left, or rearword to gewünschten Richtung Stellung “A”oder
Spingere in avanti per la sinistra, spin- “B” zu drücken.
gere indietro per la destra. Premendo turn right. Depress the end of the knob In der Stellung “A” leuchten die
l’estremità della manopola, viene emes- to operate the horn. Blinkleuchten auf der linken Seite, in der
sa una segnalazione acustica. Stellung “B” auf der rechten Seite .
Drückt man den Knopf am Hebelende,
ertönt das Horn.
0
I
A
B
II
III
4 5 6-7
21
Interruttore luminoso a due posizio- Two position light switch with secu- Schalter mit zwei Schaltstellungen
ni, con blocco di sicurezza. rity lock. und Sicherheitsverriegelung.
Il freno di stazionamento agisce sul The parking brake acts on the front Die Feststellbremse wirkt auf die
ponte anteriore. axle. Vorderachse.
- Per sbloccare il freno, spingere il - To unblock the brake, pull - Lösen der Feststellbremse:
pulsante in posizione “L”. back the lever in position “L”. Taste in die Position “L”
- Per bloccare il freno, spingere il - To block the brake, push betätigen.
pulsante in posizione “P”. the lever in position “P”. - Feststellen der Bremse: Taste
in die Position “P” betätigen.
Per sbloccare il freno da “P” a “L”, To unlock the brake from “P” to “L”, Beim Umschalten von “P” nach “L”
occorre, mentre si preme l’interrut- is necessary to push the switch and muss gleichzeitig die
tore, agire sul blocco di sicurezza. to disconnect the security lock. Sicherheitsverriegelung betätigt
werden
P
B
8 9
22
10
23
LED rosso (C) – controllo funzione Rote LED (C) -Betri~ontrolle Heizen
Red LED (C) – Operation check
di riscaldamento for heater
LED blu (F) – controllo funzione di Blue LED (F) – operation check Blaue LED (F) - Betriebskorifrolfe
ventilazione for ventilator Lüften
The mini controller enables you to Mit dem Mini-Regler haben Sie die
Il mini-regolatore consente di impostare-
set the heater installed in the vehi- Möglichkeit das im Fahrzeug eingebaute
la temperatura desiderata nell'ambiente
cle to the temperature you require. Heizgeràt nach Ihren
da riscaldare.
Temperaturwünschen eìnzu- stellen. Sie
Il mini-regolatore può essere impiegato You can either use the mini control-
können den Mini-Regler entweder im
sia per funzionamento autonomo, ler alone or in combination with the
Einzelbetrieb oder in Kombination mit
sia in combinazione con il mini- mini-clock.(Optional)
der Mini-Uhr verwenden.
timer.(Opzional)
Avviamento del riscaldatore – Start heater - heating mode: Heizgerät starten -Betriebsart Heizen:
modalità Riscaldamento:
Use the button to start the hea- Mit der Taste starten Sie das
Premere il tasto per avviare il
ter in heating mode (continuous Heizgerät in der Betriebsart Heizen
riscaldatore in modalità Riscaldamento (Dauerbetrieb). Die
operation). You can adjust the
(funzionamento continuo). La temperatu- gewünschteTemperatur können Sie mit
required temperature with the con-
ra desiderata può essere regolata con la trol knob . If the heater is in dem Drehknopf einstellen. Betindet
manopola . Quando il riscaldatore si heating mode, the red LED lights sich das Heizgerät in der Betriebsart
trova inmodalità Riscaldamento, si Heizen, leuchtet die rote LED zur
up as a check.
accende il LED di controllo rosso . Kontrolle.
24
Avviamento del riscaldatore – Start heater - ventilation mode: Helzgerät starten -Betrlebsart Lüften:
modalità Ventilazione:
Mit der Taste starten Sie das
Premere il tasto per avviare il riscal- Use the button to start the hea- Heizgerät in der Betriebsart Lüften
datore in modalità Ventilazione ter in ventilation mode (Dauerbetrieb). Der Drehknopf hat im
(funzionamento continuo). Nella moda- (continuous operation). The control Lüftenbetrieb Funktion. Befindet
lità ventilazione, la manopola knob has no function in sichdas Heizgerät in der Betriebsart
non ha nessuna funzione. Quando il ventilation mode. If the heater is in Lüften, leuchtet die blaue LED
riscaldatore si trova in modalità ventilation mode, the blue zur Kontrolle.
Ventilazione, si accende il LED di con- LED lights up as a check.
trollo blu .
Premere il tasto per spegnere il Use the button to switch off the Mit der Taste schalten Siedas
riscaldatore. La modalità di heater. Heater or ventilation Heizgerät aus. Der Heiz- bzw.
riscaldamento o di ventilazione viene mode is terminated and the Lüftenbetrieb wird beendet und die ent-
disattivata e il rispettivo LED si spegne. corresponding LED goes out. sprechende LED erlischt. Die Betriebsart
La modalità Riscaldamento termina con Heating mode is terminated with Heizen wird mit einem Nachlauf
la fase di lavaggio. after run. beendet.
Con clima molto rigido é necessario When the temperature is very low Bei Schwierigen witterungsbedingungen
accendere il motore termico prima di the engine should be started before ist es notwendig den thermischen motor
azionare l’interruttore di accensione del turning on the heating system to vor der betätigung des
riscaldamento, onde evitare il blocco del prevent a failure of ignition of the heizungSsschalters zu starten, um ein
sistema a causa dell’abbassamento del heater due to low battery voltage. blockIeren des systems auf grund eines
voltaggio della batteria. spannungsabfalls der batterie zu vermei-
den.
B
C
11
25
26
H G R L M
R
F
A B C D E
11.2
27
11/3
12
12
28
Questa leva 13 situata alla destra dell' This lever 13 is situated to the driver’s Dieser Hebel, der sich rechts vom
operatore comanda il perno che blocca left. It controls the pin that locks hydrau- Bediener befindet, dient zur
lic slewing of the lift truck. The lever has Verriegelung des Oberwagens.. Der
la rotazione idraulica del carrello eleva- Hebel kann zwei Stellungen
tore. La leva ha due posizioni: two positions:
einnehmen:
- Per inserire il perno di blocco - Push the lever to position “A” to enga- - Position A Oberwagen verriegelt.
spingere la leva in posizione "A" ge
the lock pin. - Position B Oberwagen entriegelt.
- Per disinserire il perno di blocco - Pull the lever back to position “B” to
tirare la leva indietro in posizione "B" release the lock pin.
Prima di inserire il perno nella sede per Before engaging the pin in its housing to Bevor der Oberwagen verriegelt wrden
bloccare la rotazione, verificare che la lock the slewing mechanism, check that kann, muß der Oberwagen zum
parte superiore del carrello (torretta) sia the upper part of the truck (turret) is ali- Fahrgestell ausgerichtet werden. Dies
allineata tramite la spia 3 0 . gned with the lower part by means of kann Mittels
der Kontrolleuchte "3 3 0 " (siehe.
Una volta inserito il perno la spia 3 1 telltale 3 0 (see description). Once the Beschreibung)kontrolliert werden. Ist der
segnala la presenza del perno nella pin has Oberwagen verriegelt,
sede. E' importante al momento di usare engaged, telltale 3 1 (see description) will wird die Kontrollleuchte "33 1 " aktiviert.
il comando della "Rotazione" di verifica- indicate that the pin has set in its hou- Vor der Benutzung der Funktion
re tramite la spia 3 0 che il perno non sia sing. When using the “Slewing” “Rotation 3 0 ” muß sichergestellt sein,
inserito. command, it is important to check tellta- daß der Oberwagen entriegelt ist.
Per un corretto e migliore utilizzo di que- le 3 0 in order to make sure that the pin ist. Für die korrekte
sto dispositivo fare riferimento al para- is not engaged. Refer to the “USE OF Benutzung dieser Vorrichtung siehe
Abschnitt “BENUTZUNG
grafo "UTILIZZO DEL DISPOSITIVO DI THE SLEWING DEVICE” paragraph. DER ROTATIONSVOR-RICHTUNG”.
ROTAZIONE".
Per un corretto utilizzo degli stabilzzatori Consult points 1 7 , 1 8 , 1 9 and the Für die korrekte Benutzung
fare riferimento ai punti 1 7 , 1 8 , 1 9 ed al “PROVISIONS FOR USE OF THE der Abstützung siehe die Punkte 1 7
paragrafo " DISPOSIZIONI PER L'UTI- OUTRIGGERS” paragraph in order to 1 8 , 1 9 und den Abschnitt
LIZZO DEGLI STABILIZZATORI". make correct use of these components. “ANWEISUNGEN
ÜBER DIE BENUTZUNG DER
ABSTÜTZUNG”
13
14
13 14
29
Solo quando l’operatore si siede sul A microswitch ensures these controls Die Bedienfunktionen werden erst dann
sedile, abilita, tramite un may only be used when the operator is freigeschaltet (über einen Mikroschalter
microinterruttore sat on the seat. in der Sitzfläche), wenn der Fahrer auf
presenza uomo, i comandi dei dem Sitz Platz genommen hat.
manipolatori.
15.2
15.1
15
30
Seleziona la funzione del pulsante It selects the function of the rocker button
basculante “P” sul servocomando Wählt die Funktion des Drucktasters
"15.2" (SINISTRO). “P” on servocontrol "15.2" (LEFT).
“P” auf der Servosteuerung “15.2”
Quando il selettore è in posizione A il When the selector is in position A, the
(LINKS) an.
pulsante basculante del servocomando rocker button on servocontrol "15.2"
Wenn der Wahlschalter nicht leuchtet
"15.2" (SINISTRO) comanda un even- (LEFT) controls a hydraulic accessory (if
(Stellung A),steuert der Drucktaster die
tuale accessorio idraulico (se presente). present).
Per ulteriori informazioni di comando Zubehörteile (falls vorhanden).
For further control information (pos. B/C)
(pos. B/C) vedere sul “Manuale d'utiliz- Über die Funktionen (pos. B/C) siehe.
see the specific “Basket user manual”.
zo cestello” specifico. “Bedienungsanleitung für die
Arbeitsplattform”.
Seleziona la funzione del pulsante Select the function of the rocker button
“P” on serve-control “15.2” (LEFT) Steuert die Funktion des Kippschalters
basculante “P” sul servocomando “P” auf der Servosteuerung “15.2”
“15.2” (SINISTRO) (LINKS) Der Schalter verfügt über zwei
Light switch with two positions: Schaltstellungen:
L’interruttore luminoso ha 2 posizioni :
- push “D”, the optional control is not
- premendo in “D”, il comando optional allowed and the warning light is swit - in der Stellung “D” ist die
é disabilitato e la spia luminosa è ched off Zusatzhydraulik deaktiviert und die
spenta; - push “E”, the optional control is Kontrollleuchte ist aus;
allowed and the warning light is - in der Stellung “E” ist die
- premendo in “E”, il comando optional Zusatzhydraulik aktiviert und die
é abilitato e la spia luminosa è accesa. switched on
Kontrollleuchte leuchtet.
Solo dopo avere abilitato il comando Use the optional control is only allowed Das Anbaugerät kann nur bei aktivierter
optional è possibile l’utilizzo del and the warning light is switched on. Zusatzhydraulik verwendet werden.
accessorio.
15.3
15.2
E D
15.4
31
I perni di bloccaggio devono fuoriuscire Ensure the locking pins are fully enga- Zur Verriegelung des Anbaugerätes
completamente dai fori dell’attacco rapi- ged in the quick connection holes to müssen die Verriegelungsbolzen voll-
do per bloccare l’accessorio (FIG. 15.5). lock the attachment in place (FIG. 15.5). ständig aus den Bohrungen an der
Schnellbefestigung herausragen.
Il selettore 1 5 . 4 pag.27 deve rimanere The selector 1 5 . 4 page.27 must stay in Der Wahlschalter 1 5 . 4 Seite 27 muss
in posizione “E” per evitare di sbloccare position “E” to prevent accidental relea- sich in Stellung "E" befinden, damit das
accidentalmente l’accessorio durante il se of the attachment whilst operating. Anbaugerät beim Arbeiten nicht ver-
lavoro. sehentlich entriegelt werden kann.
If the attachment has hydraulic quick
release couplings carry out the following Sollte das angebaute Gerät mit hydrau-
Se poi l’accessorio montato è provvisto procedure: lischen Anschlüssen versehen sein, ist
di raccordi idraulici procedere come - stop the engine wie folgt vorzugehen:
segue: - disconnect the hydraulic locking hose – Antriebsmotor abstellen und ca. 1
- arrestare il motore termico Minute warten,
fittings (FIG. 15.6) and stow them – Hydraulikanschlüsse vom
- scollegare i raccordi idraulici del bloc- away (ref. 1 Fig. 15.7) Zusatzhydraulikblock abkoppeln
co accessori idraulico (FIG. 15.6) e - connect the quick release couplings. (ABB.
alloggiarli negli appositi porta innesti (ref. 2 Fig. 15.7) 15.6) und in den entsprechenden
(rif. 1 FIG. 15.7) Kupplungshalterungen aufbewahren
(Nr. 1, ABB. 15.7),
- connettere i raccordi rapidi dell’acc’es-
– Schnellkuppler des Anbaugerätes an
sorio montato sull’attacco rapido (rif. 2 die Schnellverschlüsse anschließen
FIG. 15.7) (Pos. 2, ABB. 15.7).
15.5
1
2
15.6 15.7
32
16
FIG. 16
33
Situati sul cruscotto a destra davanti Installed on the control panel to the
all'operatore n°4 pulsanti selezionano right, in front of the driver, there are 4 Auf dem Armaturenbrett rechts vom
gli stabilizzatori (1 per ogni stabilizza- buttons (A,B,C,D) to select the Fahrer sind 4 Schalter(A B C,D)
outriggers (1 for each outrigger). angeordnet, mit denen man die
tore).
Abstützung anwählt (jeweils ein Schalter
Button A:Selects the front left outrigger. pro Abstützung).
Selettore A:Seleziona lo stabilizzatore Button B:Selects the front right
anteriore sinistro outrigger.
Selettore B:Seleziona lo stabilizzatore Schalter A: Wählt die Abstützung vorne
anteriore destro Button C:Selects the rear left outrigger. links an.
Selettore C:Seleziona lo stabilizzatore Button D:Selects the rear right Schalter B: Wählt die Abstützung vorne
posteriore sinistro outrigger. rechts an.
Selettore D:Seleziona lo stabilizzatore Schalter C: Wählt die Abstützung hinten
posteriore destro links an.
Schalter D:Wählt die Abstützung hinten
rechts an.
Quando la scelta è stata effettuata il When the selection has been made, the
selettore si illumina. switch illuminates. Die Anwahl wird dadurch angezeigt, daß
die Taste aufleuchtet.
A B 19
C D
18 B 19
17
34
Segnala l'allineamento delle ruote Indicates that the rear wheels are Diese Kontrollleuchte leuchtet, wenn die
anteriori rispetto all'asse del veicolo. aligned in relation to the truck axis. Vorderräder parallel zur Längsachse des
Quando le ruote sono allineate la spia si The warning light will come on when the Teleskopladers ausgerichtet sind. *
illumina. * wheels are aligned.*
* Procedura: Premere il selettore dei tipi * Räder ausrichten:
*Procedure: Set steering selector 20 to 1) Wahlschalter Lenkungsart 20 in
di sterzata 20 in posizione “1”, girare il position “1”. Turn the steering wheel
volante fino a che la spia gialla allinea- until the yellow warning light comes on, Stellung "1" betätigen und Lenkrad so
mento ruote posteriori non si illumina; then set the steering selector 20 to lange drehen, bis die gelbe
poi posizionare il selettore tipi di sterza- position “2” and turn the steering wheel Kontrollleuchte Ausrichtung Hinterräder
tura 20 in posizione "2" e girare il volan- until the green warning light comes on. aufleuchtet.
te fino a che la spia verde allineamento When the front and rear wheels are ali- 2) Wahlschalter Lenkungsart 20 in
ruote anteriori non si illumina. gned you may choose the desired mode Stellung "2" betätigen und Lenkrad so
Quando sia le ruote anteriori e posteriori of steering. lange drehen, bis die grüne
sono allineate, si può selezionare uno Kontrollleuchte Ausrichtung Vorderräder
dei suddetti 3 tipi di sterzata. During the use of the crane may happen aufleuchtet.
that the wheel are not aligned, so at 3) Wenn sowohl Vorder- als auch
Con l’uso può verificarsi lo scoordina- least every 20 hours make the procedu- Hinterräder ausgerichtet sind, kann eine
mento delle ruote, almeno ogni 20 ore di re for the alignement wheels. der drei oben genannten Lenkungsarten
funzionamento eseguire il riallineamento gewählt werden.
delle ruote come descritto nella proce-
dura. Nach längerem Betrieb können bei der
Radausrichtung Abweichungen auftre-
ten; deshalb sind mindestens alle 20
Betriebsstunden die Räder wie oben
beschrieben neu auszurichten.
1
22
20
20
21
35
26 - SPIA GIALLA BLOCCO PONTE 2 6 - REAR AXLE LOCK YELLOW 2 6 - GELBE KONTROLLLEUCHTE
POSTERIORE WARNING LIGHT VERRIEGELUNG DER
HINTERACHSE
Questa spia lampeggia quando si attiva The warning light comes on when the
il blocco ponte posteriore. rear axle lock is activated.The rear axle Diese Kontrollleuchte blinkt, wenn die
Verriegelung der Hinterachse aktiviert
Il blocco del ponte posteriore è locks is automatically if : ist.
automatico e avviene per : - the turret is rotated more than15° Die Verriegelung der Hinterachse erfolgt
- rotazione torretta oltre 15° (ogni lato) - the boom is raised more than 60° automatisch unter den folgenden
- sollevamento braccio non oltre 60° dal Bedingungen:
- bei einer Drehung des Oberwagens
suolo. um mehr als 15° (beidseitig)
- wenn der Teleskopausleger nicht um
mehr als 60° vom Boden angehoben ist.
2 7 - SPIA NON UTILIZZATA 27 - NOT USED WARNING LIGHT 2 7 - GRÜNE FREI VERFÜGBAR
2 8 - SPIA NON UTILIZZATA 2 8 - NOT USED WARNING LIGHT 2 8 - GRÜNE FREI VERFÜGBAR
25 27 28
23 24 26 29
36
Segnala l'allineamento dell'asse longitu- Indicates that the longitudinal axis of the
dinale della torretta con l'asse longitudi- turret is aligned with the longitudinal axis Diese Kontrollleuchte wird aktiviert,
nale del telaio. Quando la torretta è alli- of the chassis. The light will come on wenn der Oberwagen zur
neata la spia si illumina. when the turret is aligned. Fahrzeuglängsachse ausgerichtet ist.
Segnala l'inserimento del perno di bloc- Indicates that the rotation lock pin has Diese Kontrollleuchte wird aktiviert,
co rotazione comandato dalla leva 13 engaged following use of lever 13 (see wenn die Verriegelung der
(vedere descrizione). Quando il perno è description). The warning light will come Rotationsfunktion arretiert ist.
inserito la spia si illumina. on when the pin has engaged.
Il pulsante “33” (solo con radiocoman- This optional switch”33” (only used with Mit dem Schalter “33” (nur mit
do), ha la funzione di aumentare o dimi- a radio control) can electrically increase Funksteuerung) kann die Drehzahl des
nuire elettricamente, il numero dei giri Antriebsmotors elektrisch angehoben
del motore termico. or reduce the engine revs. It has two
positions: oder verringert werden. Der Schalter
Il pulsante ha due posizioni : verfügt über zwei Schaltstellungen:
- premendo “4” si accelera gradualmen - pushing button “4” progressively
te il motore termico speeds - Durch Betätigen des Schalters nach
- premendo “5” si decelera gradualmen- up the engine revs. “4”
te il motore termico. wird die Motordrehzahl stufenweise
angehoben.
- pushing button “5” gradually reduces - Durch Betätigen des Schalters nach
Per portare il motore termico a regime di the engine revs.
giri desiderato, premere “4”, poi rilascia- “5”
re il pulsante, per mantenere costante i wird die Motordrehzahl stufenweise ver
To select the revs required push button ringert.
giri motore. Per tornare al minimo dei “4” and release it at the rev rate required
giri motore, riselezionare il pulsante pre- “5”.
mendo“5”. Um den Antriebsmotor auf die gewün-
The return to normal tickover revs push schte Drehzahl zu bringen, Schalter in
button “5”. Stellung "4" betätigen, danach loslassen,
um die Motordrehzahl konstant zu hal-
ten. Um zur Mindestdrehzahl zurück-
zukehren, Schalter in Stellung "5" betäti-
gen.
31
32
30
37
Interruttore luminoso “33”, a due posizio- Optional switch “33” has two positions, Schalter “33” mit den Schaltstellungen
ni “C” e “D”, con blocco di sicurezza: “C” and “D” with a security lock : “C” und “D” und Sicherheitsverriegelung:
- Durch Betätigen des Schalters nach
- premendo su “C” il radiocomando - when position “C” is selected the radio “C” wird die Funksteuerung ausge
viene disabilitato; control is off. schaltet;
- premendo su “D” il radiocomando - when position “D” is selected the radio - Durch Betätigen des Schalters nach
viene abilitato e si illumina la spia sul “D” wird die Funksteuerung
interruttore. control is on and the switch lamp is lit. eingeschaltet und die Kontrollleuchte
im Schalter leuchtet auf.
Per disinserire il comando da “D” a “C” To disconnect the switch control from
occorre sbloccare il blocco di sicurezza Beim Umschalten von "D" nach "C"
“D” to “C” is necessary to disactivate the muss die Sicherheitsverriegelung ausge-
e premere l’interruttore.
security lock and push the switch. rastet und der Schalter gedrückt wer-
den.
Quando si abilita il radiocomando Ensure all functions are working correc- Beim Einschalten der Funksteuerung
tramite l’interruttore, per sicurezza, si tly when the radio control is activated. über den Schalter wird aus
spegne la macchina. Sicherheitsgründen der Teleskoplader
abgeschaltet.
35
B
34
C
D
33
38
- Per disattivare i movimenti premere - Pushing the red button to deactivates - Zum Sperren der hydraulischen
sul pulsante rosso. the movements. Funktionen dierote Drucktaste betäti
gen.
- Per ripristinare i movimenti ruotare il - Turn the red button in a clockwise - Zur erneuten Freigabe der
pulsante rosso in senso orario. direction to reset the movements. hydraulischen Funktionen die rote
Taste im Uhrzeigersinn drehen.
36
39
3 9 - LEVA D’APERTURA DEL 3 9 - REAR WINDOW OPENING 3 9 - HEBEL ZUM ÖFFNEN DES
FINESTRINO POSTERIORE LEVER HECHFENSTERS
Per l'apertura del finestrino posteriore Pull the lever in an clockwise Zum Öffnen des Heckfensters den
tirare la leva in senso orario e spinge- direction and push on the glass to Hebel entgegen dem Uhrzeigersinn
re il vetro. open the rear window. drehen und die Scheibe nach außen
drücken.
37 38
39 40
40
Posizione chiusa : per aprire, premere la Closed position: To open, press the Bei geschlossener Türhälfte: Zum Öff-
serratura “A” verso il basso. lock “A” toward the bottom. nen Verschlussknebel “A” nach unten
To close, just pull on the special drücken.
Per chiudere, basta tirare dall'apposita handle “B” toward the interior. Zum Schließen einfach den entspre-
maniglia “B” verso l'interno. Open position : chenden Handgriff "B" nach innen
Posizione aperta :spingere la portiera push the top door toward the cab to ziehen.
superiore verso la cabina per bloccarla lock it in the latch “D”. Bei geöffneter Türhälfte: Obere Türhälfte
nel chiavistello “D”. To release it, press knob “E”. in Richtung Kabine drücken und in
Per il rilascio premere il pomello “E”. Riegel “D” einrasten lassen.
Zum Entriegeln auf Entsperrknopf “E”
drücken.
43
A
C
41
A
⇪
B
⇪
D
E
⇪ ⇪
B
42 A
41
Posizionamento sulla macchina dei Components location on the machine Position der lmb komponenten an
componenti del limitatore der maschine
The sensors are positioned on the boom
I dispositivi di rilevamento sono installati and cylinders in order to detect data Die Meßwertaufnehmer zur Erfassung
sulla struttura della macchina per rilevar- when working, while the main unit and
der aktuellen Daten befinden sich am
ne i dati in fase di lavoro, mentre l’unità the control panel are located inside the
Ausleger und an den
centrale ed il pannello di controllo si cabin.
Hydraulikzylindern. Zentraleinheit und
ritrovano in cabina, a disposizione dell’o-
Anzeigegerät sind in der Fahrerkabine
peratore.
untergebracht.
1 - Sensore d’angolo e sfilo: sul lato 1 - Length/Angle sensor: on the left side
sinistro del braccio. of the boom 1 - Auslegerlängen- und winkelgeber:
Auf der in Fahrtrichtung linken
2 - Nr. 4 Trasduttori di Pressione: sui 2 - Nr. 4 Pressure Transducers: on Main Seite des Auslegers
cilindri di sollevamento e di and Compensation cylinders.
compensazione. 2 - 4 hydr. Druckaufnehmer: jeweils 2
an dem Haupt und dem
3 - Pannello Comandi: in cabina. 3 - Control Panel: in the cabin. Kompensations zylinder
4 - Unità Centrale: in cabina. 4 - Main Unit: in the cabin. 3 - Anzeigegerät:I n der fahrerkabine
5 - Lampeggiante rosso esclusione 5 - Red lamp off the safety device. 4 - Zentraleinheit: In der Fahrerkabine
“Sistema di sicurezza”
5 - Rundumleuchte Ausschalten des
Sicherheitssystems.
44
1 5
42
44.1 - Descrizione del pannello di 44.1 - Control panel description 44.1 - Beschreibung des
controllo anzeigegeräts
Fornisce all’operatore tutte informazioni It gives to the operator all information in Es gibt dem Fahrer Informationen, um im
utili a lavorare correttamente e permette order to work in safe conditions and sicheren Bereich zu arbeiten und gestattet die
le selezioni necessarie. allows proper setting. Eingabe einsatzrelevanter Daten.
7
44.1
1 2 3
43
Cosa verificare all’avviamento della What we have to check when starting Was wird nach dem Anlassen der
macchina? the machine? Maschine überprüft ?
Il pannello, dopo l’auto-controllo, informa Once the self test is processed, the con- Nach Beendigung des Funktionstests
l’Operatore sulle condizioni di lavoro trol panel informs the operator of the wird auf dem Display der zuvor eingege-
nelle quali si trova la macchina e ad working conditions which the machine is bene Betriebszustand (Anbaugerät und
ogni accensione il sistema automatica- set asking to check it and at this stage, Arbeitsbereich) angezeigt, die der
mente si riporta all’ultimo accessorio uti- the display shows the page where the Fahrer unbedingt auf Richtigkeit zuü
lizzato. main readings are monitored. überprüfen hat.
OM = Modo Operativo (da selezioni OM = Operating Mode (from external OM = der Arbeitsbereich
automatiche esterne). automatic Inputs).
Sono possibili 4 modi operativi: There are 4 possible operating modes: - 360° auf Stützen
- Su Stabilizzatori - On Outrigger fully extended - 360° auf _ Stützen
- Su stabilizzatori parzialmente sfilati. - On outriggers partially extended - auf Rädern nach vorne
- Su gomme (torretta frontale). - On wheels (turret frontal). - auf Rädern zur Seite
- Su gomme (torretta ruotata). - On wheels (turret rotaded).
T = Tabella di Carico corrispondente T = Load Table corresponding to the T = Traglastdiagramme für zubehor in
all’attrezzatura in uso. last selected attachment. benutz
44
Condizioni di carico, %, ed allarmi Lifting Conditions % and alarms Auslastung in % und warnungen
1 - Barra LCD sul display alfanumerico 1 - LCD bar showing the lifted load in 1 - LCD Balkenanzeige, die sich auf die
indicante la percentuale di carico percentage to the maximum darüber befindliche dreifarbige
sollevato rispetto al carico massimo admitted load in that working Skala bezieht und auf der das
sollevabile in quelle condizioni di condition. Verhältnis der aktuellen Last zur
lavoro. 2 - Green reference: Safe Zone. maximal zulässigen Last dargestellt
2 - Riferimento Verde: Zona di 3 - Amber reference: Alarm Zone (Lifted wird.
2 - Grüner Bereich: Zulässiger
Sicurezza. load higher than 90% of maximum
Arbeitsbereich.
3 - Riferimento Giallo: Zona di Allarme admitted load).
3 - Gelber Bereich: Vorwarnung (die
(carico sollevato superiore al 90% 4 - Red reference: Shut-off Zone (Lifted gehobene Last ist größer als 90%
del carico ammesso). load higher than al 100% of der maximal zulässigen Last).
4 - Riferimento Rosso: Zona di Blocco maximum admitted load). 4 - Roter Bereich: Abschaltung ( die
(carico sollevato superiore al 100% 5 - Green light on: Safe Working. gehobene Last ist gleich oder
del carico ammesso). 6 - Amber light on: Alarm (External größer 100% der maximal
5 - Spia Verde accesa: Sicurezza. buzzer on). zulässigen Last).
6 - Spia GIalla accesa: Allarme. 7 - Red light on: Dangerous movements 5 - Grüne Warnleuchte an: zulässiger
(avvisatore acustico esterno attivo). shut off (External buzzer on and the Arbeitsbereich
7 - Spia Rossa accesa: Blocco red rotating lamp is lighted). 6 - Gelbe Warnleuchte an: Vorwarnung
movimenti (avvisatore acustico (zusammen mit einem externen
esterno attivo con girofaro rosso akustischen Alarm)
acceso). 7 - Rote Warnleuchte an: Abschaltung
der lastmomentvergrößernden
Bewegungen (zusammen mit einem
externen akustischen Alarm).
Lettura dei dati di lavoro principali Main Working Data Reading on the Wichtige einsatzdaten.
sul display alfanumerico. display.
8 - PESO DEL CARICO SOLLEVATO, 8 - LIFTED LOAD WEIGHT: It shows up 8 - GEWICHT DER GEHOBENEN
indicato solo se si opera con forche when the forks are selected with LAST: Diese Anzeige erscheint,
in condizioni di braccio the boom completely in (as a option wenn das Anbaugerät “Gabeln”
completamente rientrato (in opzione it is available also when other eingegeben wurde und der Ausleger
è indicato anche in tutte le attachments used, ganz eingefahren ist (als Option ist
condizioni di sfilamento). regardless of the boom extension). diese Funktion auch für die
Simbolo: ACT (lettura in Graphic Symbol : ACT (Reading Anbaugeräte “Winde” und
“Tonnellate”, con un decimale). in “Tonnes”, with a decimal point). “Arbeitsbühne”, unabhängig von der
9 - CARICO MASSIMO AMMESSO 9 - MAXIMUM ADMITTED LOAD: In Länge des Auslegers, erhältlich).
nella configurazione attuale della machine present configuration. Symbol : ACT Last in “Tonnen”,
mit einer Dezimalstelle.
macchina.Simbolo: MAX (lettura in Graphic symbol : MAX (Reading in 9 - MAXIMAL ZULÄSSIGE LAST: Für
“Tonnellate”, con un decimale). “Tonnes”, with a decimal point). den aktuellen Rüstzustand de
10 - RAGGIO DI LAVORO: misura della 10- WORKING RADIUS: distance from Maschine.
distanza dal centro ralla alla the centre of turret rotation to Symbol :MAX Last in “Tonnen”, mit
proiezione del punto di applicazione applied load. einer Dezimalstelle
del carico. Graphic symbol : R (Reading in 10 - AUSLADUNG: Entfernung von der
Simbolo: R (lettura in “Metri”, con “Metres”, with a decimal point). Drehmitte des Oberwagens bis zur
un decimale). 11- WORKING CONFIGURATION: Vertikalen der angehängten Last.
11 - CONFIGURAZIONE DI LAVORO. The first figure refers to the Symbol :R Ausladung in “Meter”
La prima cifra è relativa al modo Operating Mode (Graphic symbol: mit einer Dezimalstelle
operativo (OM) e la seconda cifra è OM) and the second figure refers to 11 - RÜSTZUSTAND:
relativa all’attrezzatura in uso (T). the attachment been used Die erste Zahl zeigt den
(Graphic symbol: T). Arbeitsbereich an: Symbol: OM
Die zweite Zahl zeig das
Anbaugerät Symbol: T
In caso di selezione all’origine di siste- In case of Imperial Measure System, the Bei einer Anzeige im britischen
ma anglosassone i carichi vengono weight will be defined in “Pounds/1000” Maßsystem werden die Last in
impostati in “libbre” e i dati geometrici in and the geometric data in “Feet”. “Pounds/1000” und die
“piedi”. geometrischen Größen in “Feet” darge-
stellt.
45
Lettura dei dati di lavoro complemen- Reading of complementary working Ergänzende einsatzdaten
tari sul display alfanumerico data on the display
Premendo il tasto ENTER, il display per Pressing the ENTER push button the Bei Drücken der “ENTER” Taste werden
alcuni secondi visualizza i valori relativi display shows as follows : folgende Daten angezeigt, es werden für
alle letture colplementari L, A, H. For a few seconds, it monitors the com- einige Sekunden die ergänzenden
Successivamente il display ritorna alle plementary data values of L, A, H. Daten “L”, “A” und “H” angezeigt.
letture principali ACT, MAX, R. After that, the display gets back to its Danach wechselt das Display zurück zur
main reading of ACT, MAX, R. Anzeige der aktuellen Last, der maximal
zulässigen Last und der Ausladung.
12 - LUNGHEZZA DEL BRACCIO.
Simbolo grafico sottostante: L 12 - BOOM LENGTH. 12 - AUSLEGERLÄNGE
(lettura in “Metri”, con un decimale). Graphic Symbol : L Symbol :L Auslegerlänge in
(Reading in “Meters”, with a “Meter” mit einer Dezimalstelle
13 - ANGOLO DEL BRACCIO. decimal point).
Simbolo grafico sottostante: A 13 - BOOM ANGLE. 13 - AUSLEGERWINKEL
(lettura in “Gradi”, con un decimale). Graphic Symbol : A Symbol :A Auslegerwinkel in
(Reading in “Degrees” with a “Grad” mit einer Dezimalstelle
13 - ALTEZZA DA TERRA. decimal point).
Simbolo grafico sottostante: H 14 - HEIGHT FROM GROUND. 14 - HÖHE VOM BODEN
(lettura in “Metri”, con un decimale). Graphic Symbol : H Symbol :R Höhe in “Meter” mit
(Reading in “Metres”, with a einer Dezimalstelle
decimal point).
Lettura contemporanea di tutti i dati Reading all working data simulta- Gleichzeitige anzeige aller daten
di lavoro sul display alfanumerico neously (Optional)
(Optional)
Per la lettura dell’altezza da terra H (14), For reading the hight from ground H(14) Zur anzeige der höhe vom boden ist die
premere il tasto ENTER. push the ENTER button. “enter” taste zu drücken.
5 6 7 15 2 3 4 16
44.2
****** 1
8 9 10 11
12 13 14
46
SELEZIONE DELL’ATTREZZATURA SELECTING THE ATTACHMENT AND VORGABE DES ANBAUGERÄTS UND
PRESCELTA E MODO OPERATIVO OPERATING MODE DES ARBEITSBEREICHS
La macchina può utilizzare diverse The machine can work with different die Maschine kann mit verschiedenen
attrezzature di lavoro caratterizzate da attachment and their related Tables Anbaugeräten und den diesen zugeord-
Tabelle di Carico differenti che which are going to be selected by the neten Tragfähigkeitstabellen, die vom
l’Operatore deve selezionare. Le Tabelle Operator. The load Charts, are also Fahrer einzugeben sind, eingesetzt wer-
cambiano anche in funzione del Modo changing by the different Operating den. Auch für die verschiedenen
Operativo della macchina, ma queste Modes of the machine but this is done Arbeitsbereiche der Maschine gibt es
selezioni avvengono automaticamente automatically by micro-switches installed unterschiedliche Tragfähigkeits-tabellen,
tramite i micro-interruttori installati. onboard . die jedoch automatisch über
Mikroschalter vorgegeben werden.
Ogni qualvolta vi è la necessità di cam-
biare l’attrezzatura di lavoro (ad esem- Every time that an attachment need to Im Hautmenü, der Standardanzeige,
pio vengono smontate le forche e viene be replaced, i.e. forks get removed and werden das eingegebene Anbaugerät T
montato un Jib), va impostata manual- the jib gets fitted, this setting must be und der Arbeitsbereich OM durch Ziffern
mente sul pannello la corretta tabella (T) done manually on the control panel, entsprechend dem folgenden.
relativa. selecting the proper related Table (T).
L’impostazione del modo operativo (OM) The selection of the Operating Mode
è invecie automatica in quanto selezio- (OM) is automatic because of the exter-
nata da micro-interruttori esterni. nal micro-switches.
Nella pagina principale, normalmente In the main page, basically displayed,
visualizzata, la Tabella dell’attrezzatura the selected attachment Table (T), and
selezionata (T) ed il Modo Operativo the machine Operating Mode (OM), get
(OM) della macchina vengono visualiz- monitored on area shown below, by
zati nella zona evidenziata sottoforma di numbers.
numeri. Following example of working conditions
shows.
Indicazione in forma testo Monitoring through text messages Anzeige über Textmitteilungen
Per migliore comprensione, le condizioni In order to have an easier understanding Um die Einstellungen noch leichter
di lavoro, ovvero il Modo Operativo (OM) of working condition, the OM Operating erkenntlich zu machen, kann der
e la tabella (T), possono essere visualiz- Mode and the T Load Table can also be Arbeitsbereich OM und die zugehörende
zate sotto forma di testo: premendo il monitored in text form: Tragfähigkeitstabelle T auch in Textform
tasto INDEX il visualizzatore mostra la Pressing the INDEX button, the display angezeigt werden:
scritta in chiaro del Modo Operativo pre- will show very clearly the Operating Bei Betätigen der “INDEX” Taste erfolgt
sente e della Tabella dell’attrezzatura Mode and the selected attachment. die Anzeige des Anbaugeräts und des
selezionata. This page will be held for three Arbeitsbereichs in Textform.
Questa visualizzazione è mantenuta per seconds; after that the display gets back Diese Anzeige erscheint für etwa 3
3 secondi dopo di che il pannello ritorna to the main working page. Sekunden. Danach wechselt das
alla visualizzazione principale di lavoro. Display wieder zum Hauptmenü zurück.
Partendo dalla visualizzazione di base Starting from the basic monitoring, press Aus dem Hauptmenü erreicht man durch
premere il tasto INDEX per passare alla the INDEX button in order to change Betätigen der “INDEX” Taste das Menü,
pagina riportante i testi relativi al Modo from that page to the page related to das sich auf den Arbeitsbereich OM und
Operativo (OM) corrente ed alla Tabella the (OM) Operating Mode and the T die dem Anbaugerät zugeordnete
(T) relativa all’attrezzatura in uso. Tables related to the attachment being Tragfähigkeitstabelle T bezieht.
La prima pressione del tasto INDEX used. Mit derselben “INDEX” Taste kann nun
mostra l’attrezzatura in uso, per il cam- The first pushed “INDEX” botton shows durch wiederholte Betätigung das
biamento di quest’ultima premere il tasto the jib used, to change and visualised gewünschte Anbaugerät mit der zugehö-
fino a visualizzare quella appropriata. the jib push again the switch until to see renden
wich you disered. Tragfähigkeitstabelle aufgerufen werden.
Durante questa fase il sistema si pone During this operation, the system will Während dieses Einstellvorgangs akti-
automaticamente in blocco automatically put itself in shut-down viert das System automatisch die
condition. Abschaltfunktion.
47
Dopo aver selezionato la Tabella corret- After the right Table gets selected, press Bei Anzeige des gewünschten
ta premere il tasto ENTER per confer- the ENTER button to confirm the selec- Anbaugeräts und des Arbeitsbereichs
mare la selezione e rendere operativo il tion in order to make it effective. nun die “ENTER” Taste betätigen, um
controllo. das Programm zu aktivieren.
Ora la macchina può iniziare ad opera- Now the machine is ready to work. Die Maschine ist nun einsatzbereit.
re. Stopping and/or restarting the machine Auch bei Abschalten und anschließen-
La Tabella selezionata rimarra tale the previous Table will be kept valid, dem Wiedereinschalten der Maschine
anche dopo aver spento e riacceso la until the next manual selection will be bleibt diese Einstellung so lange aktiv,
macchina, fino alla selezione manuale done. bis eine neue Einstellung erfolgt.
successiva.
In caso di bisogno, rivolgersi If necessary, contact your agent or dea- Im Zweifelsfall fragen Sie Ihren
al vostro agente o concessionario. ler. oder Vertragshändler.
48
E’ necessario sapere prima di utilizzare All the recommendations and rules from Den Anweisungen des Herstellers ist in
la macchina tutte le prescrizioni racco- the Manufacturer to work wisely and jedem Fall Folge zu leisten.
mandate dalle Norme e dal Costruttore. consciously in any time and situation
Si raccomanda inoltre di lavorare con
prudenza e consapevolezza in tutte le
condizioni di lavoro.
- Il limitatore di carico è un apparato - The LMI is an electronic device with - Die LMB hat die Aufgabe, den
elettronico che ha lo scopo di aiutare the aim to help the operator in the Bediener
l’Operatore all’uso in sicurezza della current use of the machine, warning der Maschine bei einem Arbeitseinsatz
macchina, avvertendo con him by means of visual and acoustic zu unterstützen und ihm
segnalazioni visive ed acustiche signals while approaching dangerous das Annähern und Erreichen von
l’approssimarsi della zona di pericolo. conditions. Grenzzuständen durch optische und
- Tuttavia, tale dispositivo non può - However this device can’t replace the akustische Meldungen anzuzeigen.
sostituire la buona esperienza operator good experience in the safe - Die LMB kann niemals den
dell’Operatore all’uso in sicurezza della use of the machine. Sachverstand
macchina. - The responsibility of the operations in und die Erfahrung des Bedieners
- La responsabilità delle operazioni in safe conditions of the machine is the ersetzen.
sicurezza della macchina rimangono a operator concern as well as the - Die Verantwortung für die Sicherheit
cura dell’operatore, ed accomplishment of all prescribed bei einem Arbeitseinsatz unter
all’ottemperanza di tutte le norme di safety rules Befolgung der vorgenannten
sicurezza prescritte. - The Operator must be able to detect if Sicherheitshinweise obliegt alleine dem
- L’Operatore deve essere in grado di the data given by the LMI are correct Bediener.
stabilire se i dati forniti dal limitatore and correspond to actual working - Der Bediener muß in der Lage sein zu
sono corretti e coerenti alla realtà. conditions. erkennen, ob die von der LMB
Deve inoltre saper sfruttare i dati forniti - He must be able to utilise the data ausgezeigten Daten mit dem
dal limitatore per operare in sicurezza. given by the LMI in order to operate in aktuellen Betriebszustand der
- Il limitatore essendo un apparato safe conditions in any time. Maschine übereinstimmen.
elettronico con svariati sensori può - The LMI is an electronic device - Der Bediener muß jederzeit in der
essere soggetto a guasti o a difetti. including several sensing components, Lage sein, die von der LMB
L’Operatore deve individuare tali eventi therefore it can be subject to failures angezeigten Daten für den sicheren
ed agire di conseguenza (procedere or defects. Einsatz der Maschine zu nutzen.
alla riparazione se possibile o - The operator must recognise these - Die LMB verfügt über mechanische,
chiamare l’Assistenza Tecnica events and he must take action (to hydraulische und elektronische
MANITOU). proceed to repair if possible or to call Komponenten, bei denen Störungen
- Prima di iniziare ad operare con la MANITOU Assistance). oder Versagen nicht ausgeschlossen
macchina l’Operatore, deve prendere - Before starting the operations with the wer den können.
completa visione del manuale e machine, the user must fully read this - Der Bediener muß Störungen an und
seguirne le indicazioni contenute. manual and follow the instructions at Versagen von Komponenten erkennen
- La macchina è munita di chiave di any time. können und umgehend
esclusione del blocco (Vedi punto 4 5 ) - The LMI is supplied with a key (See Maßnahmen zu deren Beseitigung ein
riservata a chi di competenza. the point 4 5 ) for shut-down function leiten (falls Beseitigung mit eigenen
- Quando la chiave viene attivata, si by-passing. Mitteln nicht möglich ist, so
accende un lampeggiante rosso When the key is activated, a flashing red ist der MANITOU-Kundendienst
(Vedi punto 4 6 ) sulla cabina come light comes on (See point 4 6 ) in the cab umgehend zu informieren).
allarme visivo per eventuali operatori as a visual warning signal for operators - Bevor die Arbeit mit der Maschine auf
esterni alla macchina. outside the machine. genommen wird, hat der Bediener die
- Nel funzionamento normale tale chiave - In normal working operations, this key vollständige Bedienungs-
deve essere posizionata in modo da must be positioned not to by-pass anleitung zu lesen und zu verstehen
non escludere il blocco. shut-down. und sämtlichen Anweisungen jederzeit
- E’ vietato fare uso di tale chiave per - It’s forbidden to use the key to lift Folge zu leisten.
operare carichi oltre le portate loads exceeding the loads values - Die LMB ist mit einem
ammesse dal costruttore. allowed by the Manufacturer. Schlüsselschalter zur Überbrückung
- La chiave va usata solo in casi - The key can be used only when an der Abschaltung ausgerüstet.
estremi; malfunzionamenti o situazioni emergency/malfunctioning occurs or a -Wenn die Zündung eingeschaltet wird,
che ne giustifichino l’uso. situation justifying its use. leuchtet als visueller Alarm für etwaige
- L’uso della chiave è ammesso solo a - Only Authorised Personnel is allowed Arbeiter außerhalb der Maschine eine
persone autorizzate e responsabili to the use of the key; they are also rote Blinkleuchte (siehe Punkt 4 6 ) auf
dell’utilizzo. responsible for it. der Kabine auf.
- Il limitatore ha un potente programma - The LMI has a powerful FAIL-SAFE - Dieser Schlüsselschalter darf während
di autodiagnostica FAIL-SAFE, atto a autodiagnosis program suitable to der Arbeit nicht zur Überbrückung der
verificare il buon funzionamento di se verify its good operations and the one Abschaltung genutzt werden. Es ist
stesso e dei trasduttori utilizzati. of its transducers. gleichfalls verboten, den Schlüssel zu
betätigen, um Lasten zu heben, die die
in den Tragfähigkeitstabellen des
Herstellers angegebenen Werte
übersteigen.
49
- Nel caso venga riscontrata - In case a trouble has been detected, - Die Benutzung des Schlüsselschalters
un’anomalia il limitatore si pone in the LMI puts itself in a safe state by ist nur gerechtfertigt, wenn bestimmte
stato di sicurezza bloccando le stopping the manoeuvres (please see Gefahren oder Versagen drohen.
manovre (vedere il capitolo the AUTODIAGNOSTIC chapter).
“AUTO-DIAGNOSTICA”). - In spite of this, the Operator, before - Es ist ausschließlich autorisierten
- Nonostante ciò l’operatore prima di starting the operation with the Personen erlaubt, den Schlüssel zu
iniziare l’uso della macchina deve machine, must take care that the LMI betätigen und alleine diese haben die
Verantwortung für den Schlüssel.
assicurarsi che il limitatore funzioni is working correctly. To do this, he
correttamente. Per fare ciò deve must verify the validity of the displayed
- Die LMB verfügt über ein leistungs
verificare la correttezza delle values by doing some tests. starkes FEHLER-DIAGNOSE-
grandezze indicate facendo delle He must verify that there are not PROGRAMM zur Überwachung der
prove, deve verificare che non ci siano messages or alarm indications; he korrekten
messaggi o indicazioni di allarme, must verify the correct operation of the - Bedienung und der
deve verificare il corretto funzionamento manoeuvre stopping functions.The Meßwertaufnehmer.
del dispositivo di blocco delle operator is responsible for the correct Wird eine Störung erkannt, dann akti
manovre. setting of the machine load table and viert die LMB automatisch die
- L’Operatore è responsabile delle therefore for the right LMI set. Abschaltung der lastmomentver
selezioni manuali delle Tabelle di - When switching-on the machine the größernden Bewegungen (siehe auch
lavoro della macchina e quindi del last selected Table is kept valid, to Kapitel AUTOMATISCHER
limitatore. allow Operator check. SELBSTTEST).
All’accensione automaticamente About this, please follow the
rimane selezionata l’ultima instructions given in the - Trotz des automatischen Selbsttests
hat sich der Bediener vor Beginn der
configurazione utilizzata. ATTACHMENT SELECTION chapter.
Arbeit von der einwandfreien Funktion
- A tale proposito seguire le indicazioni An incorrect setting of the tables, can
der LMB zu überzeugen.
riportate al capitolo “SELEZIONE cause an incorrect LMI operation and Hierzu muß er die Richtigkeit der ange
DELL’ATTREZZATURA PRESCELTA”. therefore can provoke a dangerous zeigten Daten durch einige Testssicher
Un’impostazione non corretta situation for the machine. stellen.
dell’accessorio può causare un - Operating conditions usually change Er muß sicherstellen, daß keine
funzionamento non corretto del when:Further attachment are fitted or Störmeldungen oder andere
limitatore e quindi creare una removed (jib, winch, basket, forks) and Warnungen anliegen und er hat sich
situazione pericolosa di funzionamento relevant. von der einwandfreien Funktion der
della macchina. Per questo è Table selecting mode is set on the Abschaltung zu vergewissern.
fondamentale impostare la tabella control panel. Der Bediener ist alleine verantwortlich
corretta. Outriggers Extension / Withdrawn, für die korrekte Vorgabe der
- Le condizioni operative cambiano Turret Front/360° rotation , On rüstzustand sabhängigen Daten.
generalmente quando: si montano le Wheels/Outriggers, Operating Modes
varie attrezzature (Jib, verricello, are set in automatic way by - Bei Einschalten der Maschine werden
das zuletzt eingegebene Anbaugerät
piattaforma, forche) che vanno micro-switches.
und der Arbeitsbereich angezeigt. Der
impostate sul pannello dall’operatore. - If the load machine is on the frontal
Bediener hat zu überprüfen, ob sich
Il cambio del Modo Operativo su rubbers and the tower slews 3° right or das Anbaugerät geändert hat, um die
estensione/rientro stabilizzatori, 3° left, automatically the lmi change LMB dementsprechend neu zu
torretta frontale/360°, load chart between frontal rubbers and programmieren (siehe hierzu auch
gomme/stabilizzatori è automatico. rubbers 360°. Kapitel VORGABE DES
- Se la macchina è con carico su It is allowed the reen,ter of the tower RÜSTZUSTANDS) Bei falscher
gomme frontali e si ruota la torretta 3° use of the key that it close the lmi. Vorgabe arbeitet die LMB
a destra o 3° a sinistra, uscendo dal nicht korrekt, was zu schweren
campo di lavoro frontale, Unfällen führen kann.
automaticamente il sistema di
sicurezza abbassa la portata di - Der Rüstzustand ändert sich, wenn:
carico e passa ai valori 360° su Ausrüstungen montiert oder demontiert
gomme. werden (Gitterausleger, Winde,
Per cui si possono compiere le Arbeitsbühne, Gabeln) und die
dementsprechende
operazioni di rientro e tornare nel
Tragfähigkeitstabelle angewählt ist.
campo lavorativo precedente, senza
Abstützungen aus- oder eingefahren,
disattivare il sistema di sicurezza, Oberwagen nach vorne oder 360°, auf
perché i movimenti non vengono Rädern oder Stützen.
bloccati. Der jeweilige Arbeitsbereich wird auto
matisch über Mikroschalter
vorgegeben
Attenzione ad eventuali errori di lettu- Hazard on the safety system Gefahr am sicherheitssystem
ra del carico quando il braccio é com- If the boom is completly lowered, take Beim positionieren der last unterhalb der
pletamente abbassato. In questa errors in the reading of the load lifted.
auflagefläche der maschine; Auf even-
situazione sollevare leggermente il In these conditions, raise the boom sli-
tuelle ablesefehler der aufgehobenen
braccio prima di sfilarlo e controllare ghtly before extending it and check that
che la lettura del carico sul display the load reading on the display is the last achten. In diesen bedingungen den
corrisponda al carico effettivo. same as the actual load. ausleger anheben, bevor er ausgefah-
In generale è obbligatorio seguire la Generally, it’s compulsory to follow the ren wird und prüfen, ob die anziege am
istruzioni fornite dal costruttore della Manufacturer instructions and procedu- display mit der wirklichen last
macchina. res at any time. übereinstimmt.
50
Serve per disinserire il dispositivo di Used to disengage the safety device. Dient zum Ausschalten des
sicurezza. There are two key positions (0-1). Sicherheitssystems.
La chiave ha due posizioni (0 - 1). With normal conditions of work the Der Schlüssel kann in zwei Stellungen
Nelle condizioni normali di lavoro il safety device is always activated (0 - 1) gedreht werden.
dispositivo di sicurezza è sempre (position 1). To disengage the safety Unter normalen Einsatzbedingungen
inserito (posizione 1). device keep the key “45” is position ist das Sicherheitssystem immer ein-
Per disinserire il dispositivo di sicurez- “0” and at the same time make the geschaltet (Stellung 1).
za mantenere la chiave 45 in posizio- hydraulic controls desired. When the Zum Ausschalten des
ne "0", e contemporaneamente ese- key is released automatically returns Sicherheitssystems, Schlüssel 46 in
guire i comandi idraulici desiderati, in position “1”. Stellung "0" halten und die
quando viene rilasciata automatica- Set to position “1” to engage the Arbeitshydraulik wie gewünscht betäti-
mente vi è un ritorno in posizione 1. safety device. gen. Nach dem Loslassen kehrt der
Schlüssel automatisch in die Position
1 zurück.
Ruotando la chiave 45 in posizione Turning the key 45 to "0" disables the Durch Drehen des Schlüssels 45 in
"0" si esclude il sistema di sicurezza: safety system; nothing prevents over- Stellung "0" wird das
nulla vieta il sovraccarico e/o il ribalta- loading and/or tipping of the vehicle. Sicherheitssystem ausgeschaltet: Eine
mento del mezzo. Überlast und/oder ein Umkippen des
Fahrzeugs wird nicht verhindert.
45 46
51
ELEMENTI FILTRANTI
FILTRANTI E CINGHIE - FILTERING
FILTERING ELEMENTS AND BELTS
BELTS - FILTER
FILTER UND RIEMEN
CONTROLLI - CONTROLS - KONTROLLEN
DESCRIZIONE RIFERIMENTO (1°TAGLIANDO)*
SOSTITUZIONI PERIODICHE
DESCRIPTION REFERENCE (1°COUPON) * REPLACEMENT SCHEDULE
BESCHREIBUNG ARTIKEN HR. (1°WARTUNG) * PERIODISCHE ERSETZUNG
S
: In atmosfera molto polverosa ridurne la periodicità e anticipare la sostituzione
: In heavily dusty atmosphere
: In staubiger Atmosphäre die Wechselintervalle entsprechend verringern.
10
* First 200 hrs: Manitou Special Immersed Brakes 549. (5 gal. drum, part number - 545608)
A - TUTTI I GIORNI O OGNI 10 ORE DI A - DAYLY OR EVERY 10 HOURS A - TÄGLICH ODER ALLE 10
MARCIA SERVICE BETRIEBSSTUNDEN
C - OGNI 250 ORE DI MARCIA C - EVERY 250 HOURS SERVICE C - ALLE 250 BETRIEBSSTUNDEN
C 1 - Controllare tensione cinghia C 1 - Alternator-fan-crankshaft belt C 1 - Keilriemenspannung der
alternatore Lichtmaschine prüfen.
tension.
C 2 - Controllare livello olio differenziale C 2 - Ölstand im differential der
assale anteriore e posteriore. C 2 - Check the oil level in the axle Vorder-und Hinterachse prüfen.
C 3 - Controllare livello olio riduttori differential front and rear. C 3 - Ölstand in den Endab
ruote anteriori e posteriori. C 3 - Check the oil level in the front and trieben der Vorder-und Hinterachse
C 4 - Controllare olio riduttore 2 velocità rear wheel final drivers. prüfen.
su ponte anteriore. C 4 - Checking the oil in the 2 speed C 4 - Ölstand des Vorschaltgetriebe der
C 5 - Controllare livello elettrolita reduction gear on the front axle. Vorderachse prüfen.
batteria. C 5 - Check the level of the battery C 5 - Füllstand der Batterie prüfen.
electrolyte. C 6 - Lagerbolzen des Teleskop
C 6 - Pulire e ingrassare perno abschmieren.
articolazione braccio telescopico. C 6 - Grease the pivot pin of telescopic
C 7 - Lagerbolzen der
C 7 - Pulire e ingrassare perno boom. Werkzeugaufnahme abschmieren.
articolazione attacco rapido. C 7 - Grease the pivot pin of quick C 8 - Lagerbolzen des
C 8 - Pulire e ingrassare i perni coupling. Gabelkippzylinders auf Bodenseite
martinetto inclinazione forche lato C 8 - Grease the pins of fork tilting 3 (Abb. C8/1) und Schaftseite 4
cylinder foot and rod. (Abb. C8/2) abschmieren.
stelo e fondello.
C 9 - Grease the pins of lifting cylinder C 9 - Lagerbolzen des Hubzylinders
C 9 - Pulire e ingrassare i perni auf Bodenseite und Schaftseite 6
martinetto di sollevamento lato foot and rod.
C 1 0 - Grease the pins of compensating abschmieren.
fondello e stelo. C 1 0 - Lagerbolzen des
C 1 0 - Pulire e ingrassare i perni del cylinder foot and rod.
Ausgleichzylinders
martinetto di compensazione lato C 11 - CLean and grease the cab door auf Bodenseite und Schaftseite
fondello e stelo. pivot. abschmieren.
C 11 - Pulire e ingrassare cerniera C 1 2 - Grease the oscilation bushes of C 11 - Reinigen und Schmieren der
portiera cabina. rear axle. gelenke der Kabinentür.
C 1 2 - Pulire e ingrassare boccole C 1 3 - Grease journal and universal C 1 2 - Die Lagerbuchsen der
the cardan shaft on the front side Hinterachse und der Vorderachse
oscillazione ponte posteriore e
and rear side. abschmieren.
anteriore. C 1 3 - Drehzapfen und Gelenkwelle
C 1 3 - Pulire e ingrassare crociere e C 1 4 - Grease the pins of front and rear
auf der Vorderseite und der
cardano del albero di trasmissione outrigger tilting cylinder foot
Rückseite abschmieren
lato anteriore e posteriore. androd and pivot of the front and C 1 4 - Untere Lagerbolzen und
C 1 4 - Pulire e ingrassare perni piede e rear outrigger units. obereLagerbolzen der Kippzylinder
testa martinetti inclinazione C 1 5 - Grease the slewing bearing. der vorderen und hinteren
stabilizzatori anteriori e posteriori + C 1 6 - Check the rotation reducer oil Stabilisatoren und die Lagerbolzen
perni gruppo stabilizzatori anteriori level control. der Gruppe der vorderen
e posteriori. Stabilisatoren und der hinteren
C 1 7 - Replace the engine oil and
C 1 5 - Pulire e ingrassare ralla rotazione. Stabilisatoren abschmieren.
C 1 6 - Controllare livello olio riduttore engine oil filter. C 1 5 - Drehkranz abschmieren
rotazione. C 1 6 - Ölstand Rotationsgetriebe
C 1 7 - Sostituire olio motore e filtro olio prüfen
motore. C 1 7 - Motorölwechsel und Ersetzen des
Motoröfilters.
D - OGNI 500 ORE DI MARCIA O D - EVERY 500 HOURS SERVICE OR D - ALLE 500 BETRIEBSSTUNDEN
ANNUALMENTE EACH YEAR
D 1 - Sostituire cartuccia filtro aria.z D1 -Replace the air filter cartridge.z D1 - Luftfiltereinsatz erneuern.z
D 2 - Sostituire cartuccia filtro D2 -Replace the fuel filter cartridge. D2 - Kraftstofffilterpatrone wechseln
combustibile. D3 -Replace the transmission oil filter. D3 - Getriebeölfilter wechseln
D 3 - Sostituire filtro olio trasmissione. D4 -Replace the hydraulic oil filter D4 - Hydraulikfilter erneuern.
D 4 - Sostituire cartuccia filtro olio cartridge. D5 - Entlüftungsfilter Hydrauliktank
idraulico (scarico). D 5 - Replace the hydraulic and erneuern
D 5 - Pulire sfiato olio idraulico e D 6 - Hydraulik-Filterpatrone wechseln
transmission oil vent.
trasmissione.
D 6 - Sostituire filtro di mandata circuito D 6 - Replace the delivery filter cartridge
principale
E - OGNI 1000 ORE DI MARCIA O E - EVERY 1000 HOURS SERVICE OR E - ALLE 1000 BETRIEBSSTUNDEN
ANNUALMENTE EACH YEAR
E 1 - Svuotare e sostituire olio idraulico E 1 - Change the hydraulic and E 1 - Hydrauliköl wechseln.
e trasmissione. transmission oil E 2 - Saugfilter im Hydrauliktank
E 2 - Sostituire cartuccia filtro olio E 2 - Cleaning the hydraulic suction oil
idraulico (aspirazione (saugkorb) reinigen.
cartridge.
“succhieruola”). E 3 - Differenzialöle der Vorder- und
E 3 - Change the oil in the front and
E 3 - Svuotare e sostituire olio Hinterachse wechseln.
differenziale assale anteriore e rear axle differential.
E 4 - Öle der Endabtriebe der Vorder-
posteriore. E 4 - Change the oil in the front and
rear wheel final drivers. und Hinterachse wechseln.
E 4 - Svuotare e sostituire olio riduttori
ruote anteriori e posteriori. E 5 - Cheange the oil in the front axle E 5 - Öl im Untersetzungsgetriebe der
E 5 - Svuotare e sostituire olio riduttore reduction gear. Vorderachse wechseln.
2 velocità su ponte anteriore. E 6 - Change tha air filter safety E 6 - Sicherheitspatrone des Luftfilters
E 6 - Sostituire cartuccia di sicurezza
cartridge. z erneuern.z
del filtro dell’aria. z E 7 - Changing the alternator belt/
E 7 - Pulire serbatoio combustibile. E 7 - Keilriemen der Lichtmaschine
crankshaft.
E 8 - Sostituire cinghia alternatore/ erneuern.
E 8 - Checking the chains for wear.
/albero a gomiti. E 8 - Kettenverschleiß prüfen.
E 9 - Sostituire e svuotare olio riduttore E 9 - Swing reduction unit oil change.
E 9 - Ölwechsel des
rotazione.
Untersetzungsgetriebe der
Rotatin
F - OGNI 2000 ORE DI MARCIA F - EVERY 2000 HOURS SERVICE F - ALLE 2000 BETRIEBSSTUNDEN
F 1 - Controllare gioco valvole del F 1 - Check the valve clearance.* F 1 - Ventilspiel prüfen, ggf. einstellen.
motore.* F 2 - Check the injectors.* F 2 - Einspritzdüsen prüfen.
F 2 - Controllare iniettori.* F 3 - Check the alternator and starter F 3 - Lichtmaschine und Anlasser
F 3 - Controllare alternatore e motorino motor.* prüfen.
d’avviamento.* F 4 - Check the turbocompressor.* F 4 - Turbolader prüfen.
F 4 - Controllare turbo compressore.*
Se il carrello non ha raggiunto questi The oils should be changed once a year Wenn der Hubstapler diese
tempi di lavoro le sostituzioni degli olii if the truck has not reached this number Betriebsstunden noch nicht erreicht hat,
vanno eseguite una volta all’anno. of hours service in the year. sind die Schmieröle einmal im Jahr zu
ersetzen.
z : In atmosfera polverosa ridurne la z: Carry out this operation more often z: In staubiger Atmosphäre die
periodicità e anticiparne la and change more frequently in a Wechselintervalle entsprechend
sostituzione. very dusty environment. verringern.
* Per queste operazioni consultare il * For this operations consult your * Wenden sie sich bei fehlerhaf
vostro agente o concessionario. connission agent and or the ter Einstellung an Ihren oder
concessionaire. Vertragshändler.
Verificare periodicamente ad ogni Periodically check to make sure that the Bei jedem Wartungsintervall regelmäßig
intervallo di manutenzione, il buon anti-tipping safety system operates cor- das Sicherheitssystem gegen Umkippen
funzionamento del sistema di sicurezza rectly whenever maintenance work is auf ordnungsgemäßen Betrieb prüfen.
antiribaltamento. carried out.
A - TUTTI I GIORNI O OGNI 10 ORE DI A - DAYLY OR EVERY 10 HOURS A - TÄGLICH ODER ALLE 10
MARCIA SERVICE BETRIEBSSTUNDEN
Prima di verificare il livello d’olio, assicu- Before checking the oil level, make sure Fahrzeug auf ebener Fläche abstellen.
rarsi che il motore termico sia spento e that the engine is off and that the truck Motor abstellen.
che il carrello si trovi su di una superficie is on a flat surface. To obtain an accura- Nach einer kurzen Wartezeit
piana. te indication, wait a few minutes after ( das im Kreislauf befindliche ÖL braucht
Per ottenere indicazioni precise, atten- the engine has been switched off to einige Minuten, um sich in der Ölwanne
dere qualche minuto dopo l’arresto del allow the oil to flow into the crankcase. zu sammeln) den Ölmessstab "1"herau-
motore in modo che l’olio defluisca nel Remove dipstick 1 (fig. A1/1) and, after sziehen, reinigen und wieder zurück-
carter motore. having cleaned it, check the level of the stecken.
Togliere l’indicatore di livello 1 (fig.A1/1) oil. Top up through fill hole 2 (fig. A1/2) if Nun den Ölmessstab nochmals ziehen
e dopo averlo pulito controllare il livello necessary (consult the “LUBRICANT” und den Ölstand ablesen. ( Ölmessstab
dell’olio. Eventualmente rabboccare table). während der Prüfung waagerecht hal-
attraverso il foro di riempimento 2 (fig. ten) Bei Bedarf Öleinfülldeckel "2"
A1/2) (vedere "LUBRIFICANTI"). öffnen und Ölstand ergänzen.(Abb. A1/2)
(vgl. “TABELLE DER FÜLLMENGEN”).
A 2 - Controllare livello liquido di A 2 - Check the cooling fluid level A 2 - Standkontrolle der
raffreddamento kühlflüssigkeit
Set the truck on level ground, switch off Das Fahrzeug auf ebenem Boden
Con il carrello su di una superficie piana the engine and allow it to cool. abstellen, den Motor abstellen und
e a motore spento, lasciare raffreddare il Slowly turn the plug of radiator 1 (fig. auskühlen lassen.
motore. A2) in an anticlockwise direction until Den Kühlerverschlußdeckel "1" (Abb.
Girare lentamente il tappo del radiatore reaching the safety stop. Allow the pres- A2/1) entgegen dem Uhrzeigersinn lang-
1 (fig. A2/1) in senso antiorario fino al sure and steam to escape. sam bis zum Sicherheitsanschlag los-
fermo di sicurezza. Push the plug downwards and turn it to schrauben.Überdruck und Dampf ablas-
Fare uscire la pressione e il vapore. remove. If necessary, add cooling fluid sen.Auf den Verschlußdeckel drücken,
Spingere in basso e girare il tappo in until the level is 12 mm below fill hole 2 um ihn abschrauben zu können.Falls
modo da poterlo togliere. (fig. A2). Lightly lubricate the lip of the fill erforderlich Kühlwasser nachfüllen, bis
Se necessario, aggiungere refrigerante hole to facilitate radiator plug entry. es 12 mm unter der Einfüllöffnung "2"
fino ad una altezza di 12 mm sotto il (Abb. A2/1) steht. Die Kante des
foro di riempimento 2 (fig. A2/1). Kühlerstutzens leicht schmieren, damit
- Lubrificare leggermente il bordo del der Kühlerverschraubdeckel sich besser
foro di riempimento per facilitare l’inseri- schrauben läßt.
mento del tappo del radiatore.
Non aggiungere mai liquido di raf - Never add cold cooling liquid to a Wenn die Kühlflüssigkeitr sehr warm ist,
freddamento freddo a motore caldo. caldo hot engine.
engine This series of operations
nur warme Kühlflüssigkeit zugeben
Questa serie di operazioni è da effet- must beperformed when necessary or
tuarsi quando sia necessario o una volta once a year prior to the winter. (80°C).
all’anno prima dell’inizio dell’inverno. Kühlflüssigkeit erneuern
Sostituzione del liquido di raffreddamento Replacing the cooling fluid
Dieser Vorgang ist auszuführen, nach
Bedarf, oder mindestens einmal pro
Posizionare il carrello su di una superfi- These operations should be carried out Jahr, vor Beginn der kalten Jahreszeit
cie orizzontale, fermare il motore termi- whenever necessary, or once a year .Das Fahrzeug auf ebener Fläche
co lasciarlo raffreddare. before winter starts. Set the truck on a abstellen.
Allentare il tappo di svuotamento 3 (fig. perfectly horizontal surface, switch off Motor abstellen und abkühlen lassen.
A2/2) del radiatore. the engine and allow it to cool.
Den Ablaßstopfen "3" (Abb. A2/2) am
Allentare il tappo di svuotamento 4 (fig. Slacken drain plug 3 (fig. A2/2) of the Kühler entfernen.
A2/3) del blocco motore. radiator. Den Ablaßstopfen "4" (Abb. A2/3) am
Slacken drain plug 4 (fig. A2/3) of the Motorblock los schrauben.
cylinder block.
A1/1
A1/2
2
1
1
2
Il motore non ha elementi anti-corro- The engine has no corrosion resistor Der Motor muß ganzjährig mit
sione e deve essere riempito tutto and must be filled with a minimum mindestens 25%
l’anno con una miscela minima conte- mixture of 25% ethylene-glycol based Frostschutzmittel auf der Basis von
nente 25% di antigelo. antifreeze all year round. Äthylenglykol gefüllt sein
( Korrosionsschutz)
Punto di congelamento in funzione della Freezing point according to the anti- Gefrierpunkt in Abhängigkeit der
% di antigelo. freeze % Konzentration des Frostschutzmittels in %.
360° 400°
4 5
5
Non fumare e non avvicinarsi con una Do not smoke and do not approach the Während des Tankens oder bei geöffne-
fiamma durante il riempimento del vehicle with a flame when filling the tank tenm Tank nicht rauchen und kein offe-
serbatoio o quando quest’ultimo or when the tank is open. nes Feuer oder Licht benutzen..
é aperto.
Non fare mai il pieno con il motore Never fill the tank when the engine is on. Zum Tanken den Motor immer
acceso. abgestellen.
A 4 - Controllare l’ingrassaggio dei A 4 - Check greasing of telescopic A 4 - Die Schmierung der Gleitschuhe
pattini del braccio telescopico boom sliding blocks des Teleskopauslegers prüfen
Sfilare completamente il braccio Extract telescopic boom completely and Den Teleskopausleger ganz ausziehen
telescopico e verificare il corretto check to make sure the telescopic boom und die Gleitschuhe des
sliding blocks are greased properly (if they Teleskopauslegers auf korrekte
ingrassaggio dei pattini del braccio Schmierung prüfen (sollten sie zu
telescopico (se fossero da ingrassare are to be greased, see point B 5 ).
schmieren sein, siehe Punkt B 5 ).
vedere punto B 5 ).
A3
11
Non lavare mai una cartuccia del filtro Never ever wash an air filter cartridge. Den Luftfiltereinsatz auf keinen fall
dell’aria. auswaschen.
2 4
1 3
B1/1 B1/2
12
B 2 - Controllare livello olio idraulico e B 2 - Check the hydraulic and B 2 - Füllstand Hydrauliköl prüfen
trasmissione transmission oil level
Posizionare il carrello su una superficie Set the truck on a flat surface with Das Fahrzeug auf ebener Fläche abstel-
piana con il motore spento e il braccio the engine off and the telescopic len.
telescopico ritratto e abbassato quanto boom retracted and as low as Motor abstellen, den
più possibile. possible. Teleskop soweit wie möglich einfahren
Riferirsi all’indicatore 1 (fig. B2/2). Refer to gauge 1 (fig. B2/2). und absenken.
Il livello dell’olio è corretto quando si The oil level is correct when it is Die Füllstandsanzeige "1" (Abb. B2/2)
trova tra il riferimento superiore e quello between the upper and lower marks. beachten.
inferiore. - Add oil if necessary (consult the Der Füllstand ist korrekt, wenn er sich
- Se necessario, aggiungere olio (vedere “LUBRICANT” chart) through fill hole zwischen der oberen und der unteren
“ LUBRIFICANTI") attraverso il foro di 2 (fig. B2/1). Markierung befindet.
riempimento 2 (fig. B2/1). The oil should always be kept to its Falls erforderlich durch den
E’necessario mantenere sempre il livello maximum level. Öleinfüllstutzen "2" (Abb. B2/1) Öl der
d’olio al massimo. vorgeschrieben Sorte einfüllen (vgl.
“TABELLE DER FÜLLMENGEN”).
Der Ölstand muß immer an der
oberen Markierung gehalten werden, da
die Ölmenge Einfluss auf den
Temperaturhaushalt der Hydraulik hat..
B 3 - Controllare pressione pneumatici e B3 - Check the pressure and wheel nut B 3 - Reifendruck Prüfen Fester
serraggio dadi ruote torque Sitz der Radmuttern prüfen
Controllare ed eventualmente rego- Check and adjust the tyre pressure if Den Reifendruck prüfen und ggf. korri-
lare la pressione dei pneumatici necessary (see “Specifications” chapter). gieren (vgl. Kapitel “Technische Daten”).
(vedere Capitolo "Caratteristiche"). Check the condition of the tyres. There Den Zustand der Reifen auf Verschleiß,
Verificare lo stato dei pneumatici should be no cuts, signs of wear, etc. Schnittstellen und sonstige
per ricercare eventuali tagli, protu- Check that the wheel nuts are correctly Beschädigungen
beranze, segni d’usura, etc. torqued (see CHART). prüfen.
Controllare il serraggio dei bulloni Das Anzugsdrehmoment der
delle ruote (vedere TABELLA). Radschrauben prüfen (vgl. TABELLE).
Se queste prescrizioni non vengono Failure to comply with these instructions Bei Nichtbeachtung dieser Hinweise,
osservate, si possono avere danni e could lead to damage and breakage of kann es zu Schäden und Brüchen der
rotture dei prigionieri di fissaggio the wheel studs and distortion of the Radschrauben und zur Verformung der
delle ruote con conseguenti cause wheels themselves. Reifen kommen.
accidentali.
Wheels nut torque Anzugsmoment der radmuttern
Coppia di serraggio dadi ruote Front wheels: 630Nm Vorderräder: 630Nm
Ruote anteriori: 630Nm Rear wheels: 630 Nm Hinterräder: 630 Nm
Ruote posteriori: 630 Nm
2
1
B2/1 B2/2 B3
13
B 4 - Pulire griglia del radiatore B 4 - Clean the radiator B 4 - Reinigen des kühler
Per evitare che il radiatore si otturi, To prevent the radiator from clogging, it Um eine einwandfreie Kühlleistung zu
occorre pulirlo con un getto d’aria must be cleaned with a jet of compres- garantieren, muß der Kühler alle 50
compressa rivolto da dietro in avanti sed air from the inside towards the out- Betriebsstunden gereinigt werden.,
(fig. B4). Questo è il solo modo effi- side (fig. B4). This is the only way to Den Kühler mit Druckluft von Innen
cace di eliminare le impurità. clean off the debris. nach Außen reinigen (Abb. B4).
B 5 - Pulire e ingrassare pattini B 5 - Clean and grease the telescopic B 5 - Reinigen schmieren der
d’usura del braccio telescopico Gleitschuhe des Teleskopen.
boom pads
- Fare uscire completamente il
braccio telescopico. - Completely extend the telescopic - Den Teleskopen komplett ausfahren.
- Pulire la superficie dei bracci boom. Mit einem Spachtel altes Schmierfett
sfilanti - Clean the surface of the telescopes ent fernen.
- Usando un pennello, applicare uno - Using a brush, apply a layer of - Mit einem Pinsel eine Fettschicht (vgl.
strato di grasso (vedere grease (see “LUBRICANT” chart) on “TABELLE DER FÜLLMENGEN”) auf
“LUBRIFICANTI") sui 4 lati del all 4 sides of the telescopic boom
braccio telescopico (fig. B5). (fig. B5). die 4 Seiten des Teleskopauslegers
- Azionare il braccio telescopico più - Operate the telescopic boom auftragen (Abb. B5).
volte per distribuire il grasso in several times to evenly distribute - Den Teleskopen mehrmals
modo uniforme. the grease. betätigen, um das Schmierfett zu vertei
- Togliere l’eccesso di grasso. - Remove any excess grease. len.
- Überschüssige Fett entfernen.
D
D
B4
B5
14
C - OGNI 250 ORE DI MARCIA C - EVERY 250 HOURS SERVICE C - ALLE 250 BETRIEBSSTUNDEN
C 1 - Controllare tensione cinghia C 1 - Alternator belt tension C 1 - Keilriemenspannung der
alternatore
The tension of the alternator fan belt Lichtmaschine prüfen
La tensione della cinghia del ventilatore must be adjusted so that, by exercising
alternatore deve essere regolata in a normal pressure with the thumb, the Die Keilriemenspannung der
modo che, esercitando una pressione belt flexure is about 10 mm (fig. C1 “3”). Lichtmaschine
normale con il pollice, la flessione della muß so eingestellt werden, daß der
cinghia sia di 10 mm circa (fig.C1 “3” ). Keilriemen sich mit dem Daumen um ca.
If the tension is wrong, slacken screws 1 10 mm eindrücken läßt (Abb. C1 “3”).
Nel caso di una tensione scorretta, and 2 (fig. C1) by two or three turns and
allentare le viti 1 e 2 (fig.C1) di due o tre turn the alternator unit so that the belt
giri e ruotare il gruppo alternatore in tension is correct. Falls die Spannung nachgestellt werden
modo da ottenere la tensione di cinghia Tighten screws 1 and 2 again (fig. C1). muß, die Schrauben "1" und "2" (Abb.C1)
richiesta. Check the condition of the belt (signs of um zwei oder drei Umdrehungen
Stringere di nuovo le viti 1 e 2 (fig.C1) wear or cracks) and replace it if neces- lösen und die Lichtmaschine soweit ver-
Verificare lo stato della cinghia sary. stellen, bis die korrekte
(segni di usura o screpolature) e cam- Keilriemspannungerreicht ist.
biarla, se necessario (vedere tabella Die Befestigungsschrauben "1" und "2"
“elementi filtranti e cinghie”). (Abb. C1) wieder festziehen.
Den Zustand des Keilriemens prüfen auf
Verschleiß, Rißbildung etc. prüfen und
ggf.ersetzen.
C 2 - Controllare livello olio differen- C 2 - Check the oil level in the front C 2 - Füllstand Differenzialöl prüfen.
-ziale assale anteriore e posteriore and rear axle differential
1
2
3
'
1 C1 C2
15
C 4 - Controllare olio riduttore C 4 - Checking the oil in the 2 speed C 4 - Ölstand Untersetzungsgetriebe
2 velocità su ponte reduction gear on the front axle der Vorderachse prüfen.
C3 C4
16
Controllare il livello dell'elettrolito della Check the level of the electrolyte in each Den Säurestand aller Zellen prüfen.
batteria ogni 250 ore. battery cell.
Bei höheren Temperaturen, muß die
In caso di temperatura ambiente When the ambient temperature is high, Kontrolle öfter als alle 250
elevata, controllare più frequentemente il the level should be checked more fre- Betriebsstunden vorgenommen werden.
livello. quently than once every 250 hours.
Carica della batteria : F. Charging (off the vehicle) : F. Ladung Außerhalb des fahrzeuges:
-Togliere i tappi 1 (fig. C5/1). -Remove vents 1 (fig. C5/1). -Verschlußstopfen abnehmen "1" (Abb. C5/1).
-Le batterie devono essere ricaricate -Only use direct current (DC). -Dìe Batterien dürfen nur mit
solo con corrente continua. -Connecl + wìth +, - wìlh -. Gleichstrom geladen werden.
-Collegare il cavo positivo (+) del carica -Charge at recommended bench rate i.e. -(+) Pol des Ladegerätes mìt (+) PoI der
batterie al polo positivo (+) della 10% of battery capacity. Batterie und (-) Pol des Ladegerätes
batteria e il cavo negativo (-) del carica -The battery is fully charged when mit (-) Pol der Batterie verbinden.
batterie al polo negativo (-) della batteria. specific gravìty has reached 1.28 -Als Ladestrom wird max. ein Zehntel
-Effettuare la ricarica con una corrente (1.23 under tropical climate). (1/10) der NennKapazität empfohlen.
pari a 1/10 della capacità nominale (Ah) -When charge has completed. -Die Batterie ist vollgeladen, wenn
della batteria. die Säuredichte in allen Zellen 1,28 Kg/l
-Switch off charger then disconnect.
-La batteria sarà completamente
-Check electrolyte level. beträgt (oder 1,23 Kg/l für trop. länder).
carica quando la densità dell'acido
-Nach Beendigung des Ladevorganges
è di 1,28 (1,23 per i paesi tropicali). erst das ladegerät abschalten, dann die
-A fine carica, spegnere il carica batterie Batterie abklemmen.
prima di scollegare la batteria. -Säurestand prüfen. ggf destilliertes.
-Controllare il livello dell'elettrolito. -Wasser nachfüllen.
-
2
1
2
+
C5/1
17
C 8 - Ingrassare i perni del martinetto C 8 - Grease the pins of the fork C 8 - Lagerbolzen des
inclinazione forche lato stelo 3 tilting cylinder on the foot sid Gabelkippzylinders
(fig.C8/1) e lato fondello 4 (fig.C8/2). 3 (Fig.C8/1) and on the rod 4 auf Bodenseite 3 (Abb. C8/1)
side (Fig.C8/2). und Schaftseite 4 (Abb. C8/2)
abschmieren.
C 9 - Ingrassare i perni del martinetto
di sollevamentolato lato fondello
5 (fig.C9/1) e lato stelo 6 (fig.C9/2). C 9 - Grease the pins of the lifting C 9 - Lagerbolzen des Hubzylinders
cylinder on the foot side 5 auf Bodenseite 5 (Abb. C9/1)
(Fig.C9/1) and on the rod 6 und Schaftseite 6 (Abb. C9/2)
side (Fig.C9/2). abschmieren.
2
3
C6 C7 C8/1
C8/2
C6
C7
C8/1
C9/1 C9/2
5
4 6
18
C 11 - Pulire e ingrassare le cerniere C 11 - Clean and grease the cab door C 11 - Reinigen und abschmieren der
della portiera cabina pivots lubricators schmiernippel der Kabinentür
Pulire gli ingrassatori 1 (fig.C11). Clean lubricators 1 (fig. C11). Die Schmiernippel "1" (Abb. C11) reini-
Lubrificare con del grasso ("LUBRIFI- Lubricate with grease (“LUBRICANT” gen. Mit Fett (vgl. “TABELLE DER
CANTI"). Togliere l’eccesso di grasso. chart). Remove any excess grease. FÜLLMENGEN”) abschmieren.
Überschüssiges Fett entfernen.
1 1
C11
C11
C10/2 C10/1
C10/1 C10/2
19
C 1 4 - Ingrassare i perni del piede 4 C 1 4 - Grease the pins of foot 4 C 1 4 - Untere Lagerbolzen 4
(fig.C14/1+fig.C14/2) e della (Fig.C14/1+Fig.C14/2) and head (Abb. C14/1+ Abb. C14/2)
testa 5 (fig.C14/1+fig.C14/2) 5 (Fig.C14/1+Fig.C14/2) of the und obere Lagerbolzen 5
dei martinetti inclinazione front and rear outrigger tilting (Abb. C14/1+ Abb. C14/2)
stabilizzatori anteriori e cylinders and pins 6 of the front der Kippzylinder der
posteriori e perni 6 gruppo (Fig.C14/1) and rear (Fig.C14/2) vorderen und hinteren
stabilizzatori anteriori outrigger units.
Stabilisatoren und
(fig.C14/1) e posteriori .
(fig.C14/2). die Lagerbolzen 6 der Gruppe
dervorderen Stabilisatoren
(Abb. C14/1)und der hinteren
Stabilisatoren (Abb. C14/2)
abschmieren.
1 C12/1 C12/2
2
3
2
C13/1 C13/2
20
C14/1
4 4
5 5
6 6 6 6
6 4 4
C14/2
4 4
5 5
6 6 6
6
21
C 1 5 - Pulire e ingrassare ralla rotazione C 1 5 - Grasing the slewing center plate C 1 5 - Drehkranz abschmieren
Pulire gli ingrassatori 1 (fig.C15). Clean lubricators 1 (fig. C15). Die Schmiernippel "1" (Abb. C15)
Lubrificare con del grasso (vedere Lubricate with grease (see“LUBRCANT” reinigen.
tabella"LUBRIFICANTI"). chart). Mit Fett (vgl. “TABELLE DER
Togliere l’eccesso di grasso. Remove any excess grease. FÜLLMENGEN”) abschmieren.
Überschüssiges Fett entfernen.
C 1 6 - Controllare olio riduttore rotazione C 1 6 - Check rotation reduction gear oil C 1 6 - Ölstand Rotationsgetriebe
(solo 360°) (only 360°) prüfen (only 360°)
Den Teleskopstapler mit ausgerichtetem
Position the lift truck, with turret aligned, on a Turm auf eine ebene Fläche stellen, den
Posizionare il carrello, con torretta level surface,
allineata, su di una superficie piana, Teleskopausleger ganz einfahren und
rientrare e sollevare completamente il retract and raise telescopic boom completely, heben und den Turm dann um +/- 60°
and then turn the turret to the right by nach rechts drehen, um besseren Zugriff
braccio telescopico e poi ruotare la zu den Einfüllstellen des
torretta a destra di +/- 60°, per accedere +/- 60°, for better access to the rotation
Rotationsgetriebes (Abb. C16) zu
meglio ai punti di riempimento del reduction gear filling points (Fig.C16). erhalten; den Motor abstellen und
riduttore rotazione (fig.C16); fermare il Stop the I.C. engine and wait for the hydraulic abwarten, dass das Öl sich abkühlt.
motore termico e attendere che si oil to cool down.
raffreddi l’olio idraulico. Um den Stand des Getriebeöls zu prü-
To check the oil level in the reduction unit: fen, ist folgendes erforderlich:
Per controllare il livello olio riduttore - Mit einem Schlüssel den Stopfen 1
occorre: - Unscrew cap1 using a spanner (Fig.C16/2)
and check the oil level through level indicator (Abb. C16/2) mit Ölmessstab vom
- Svitare con una chiave il tappo 1 Standanzeiger 3 abschrauben und
(fig.C16/2)con astina di livello dal 3 using a dipstick: the level must be between
den korrekten Ölstand prüfen, der
indicatore di livello 3 e verificare il the "MIN" and "MAX" line (Fig.C16/1).
sich zwischen den Kerben
corretto livello di olio, che deve essere - If the oil level is low, i.e. below the "MIN" level,
tra la linea di “MIN” e “MAX” (fig.C16/1). "MIN" und "MAX" (Abb. C16/1)
top up through opening 2 (Fig.C16/1) until the befinden muss.
- Nel caso in cui il livello di olio fosse oil touches level indicator (Fig.C16/1).
basso, cioè sotto la linea di livello - Sollte der Ölstand zu niedrig sein,
“MIN”, rabboccare olio tramite il d.h. unter der Kerbe "MIN", ist am
raccordo 2 (fig.C16/1) fino a quando Then refit the topping up and level caps. Stutzen 2 (Abb. C16/1) Ö nach
l’olio non affiora dal indicatore di livello zufüllen, bis das Öl am
3 (fig.C16/1). Standanzeiger
3 (Abb. C16/1) zu sehen ist.
Infine riavvitare i tappi di rabbocco e di
livello. Danach die Einfüll- und
Standanzeigestopfen wieder
aufschrauben.
C15
C16
MAX 3
MIN 2
C16/1
22
C 1 6 a - Controllare olio riduttore rotazione C 1 6 a - Check rotation reduction gear oil C 1 6 a - Ölstand Rotationsgetriebe
(solo 400°) (only 400°) prüfen (only 400°)
Posizionare il carrello, con torretta Position the lift truck, with turret aligned, on a Den Teleskopstapler mit ausgerichtetem
allineata, su di una superficie piana, level surface, Turm auf eine ebene Fläche stellen, den
rientrare e sollevare completamente il Teleskopausleger ganz einfahren und
retract and raise telescopic boom completely, heben und den Turm dann um +/- 60°
braccio telescopico e poi ruotare la
torretta a destra di +/- 60°, per accedere and then turn the turret to the right by nach rechts drehen, um besseren Zugriff
meglio ai punti di riempimento del +/- 60°, for better access to the rotation zu den Einfüllstellen des
riduttore rotazione (fig.C16a); fermare il reduction gear filling points (Fig.C16a). Rotationsgetriebes (Abb. C16a) zu
motore termico e attendere che si Stop the I.C. engine and wait for the hydraulic erhalten; den Motor abstellen und
raffreddi l’olio idraulico. abwarten, dass das Öl sich abkühlt.
oil to cool down.
Per controllare il livello olio riduttore To check the oil level in the reduction unit: Um den Stand des Getriebeöls zu prü-
occorre: Relieve the level plug 2 (fig. C16a/1). fen, ist folgendes erforderlich:
Togliere il tappo di livello 2 (fig.C16a/1). The level is correct when the oil surfa- Kontrollstopfen 2 (Abb.C16a/1) entfernen.
Il livello é corretto quando l'olio affiora ces and flows through the port of level Der Ölstand ist korrekt, wenn an der
e defluisce dal foro di livello 2 2 (fig. C16a/1) add oil. Kontrollöffnung 2 (Abb. C16a/1) das
(Fig.C16a/1). Trough the breater and flitting oil hole Öl ansteht.
Aggiungere olio dal foro di carico 1 1, (fig. C16a/1) if necessary, (see Ggf. durch die Einfüllöffnung
(Fig.C16a/1) se necessario, (vedere “Lubricant”). 1 (Abb. C16a/1) nachfüllen. (siehe
"LUBRIFICANTI"). “TABELLE FÜLLMENGEN”).
Infine riavvitare i tappi di rabbocco e di Then refit the topping up and level caps. Danach die Einfüll- und
livello. Standanzeigestopfen wieder
aufschrauben.
C15 C16a
1 1
2
2
C16a/1
23
C 1 7 - Sostituire l’olio motore e C 1 7 - Replace engine oil and engine C 1 7 - Motoröl wechseln und
sostituire filtro olio motore oil filter Motorölfilter ersetzen
Posizionare il carrello su di una Position the lift truck on level ground, Den Teleskoplader auf einer ebenen
superficie piana, far girare al minimo allow the engine to idle for a few minutes Fläche abstellen, den Motor ein paar
il motore per qualche minuto e poi and then switch it off. Minuten laufen lassen und dann abstel-
fermarlo. len.
Demount engine guard "1".
Smontare il carter protezione motore Das Motorschutzgehäuse "1" abneh-
“1”. Place a container under the drain plug of men.
Collocare un recipiente sotto il the engine oil sump 2 (Fig. C17/1). Einen Auffangbehälter unter den Öla-
tappo di svuotamento coppa olio Unscrew plug 2 and remove it. blassstopfen am Motor 2 (Abb. C17/1)
Then unscrew fill plug 3 (Fig.C17/2) to stellen; den Stopfen 2 losschrauben und
motore 2 (fig. C17/1); svitare il abnehmen.
tappo 2 e poi toglierlo. facilitate emptying. Außerdem den Öleinfüllstopfen 3 (Abb.
Inoltre svitare il tappo di riempimen- C17/2) abschrauben, damit das Öl bes-
to 3 (fig.C17/2) per facilitare lo Replacing filter. ser ausläuft.
svuotamento. Unscrew and remove oil filter 4
(Fig.C17/3) then discard it with its relative Filter ersetzen
Sostituzione del filtro. seal. Den Ölfilter 4 (Abb. C17/3) losschrauben
Svitare e togliere il filtro dell’olio 4 Clean the filter connector with a clean und herausnehmen. Den Filter und
(fig.C17/3) poi gettarlo con relativa cloth. seine Dichtung umweltgerecht entsor-
guarnizione. Lightly lubricate the new seal and fit a gen.
Pulire l’attacco del filtro con un new filter with the same specifications Den Filterträger mit einem sauberen
panno pulito . see ("FILTER ELEMENTS AND BELTS Lappen reinigen.
Lubrificare leggermente la nuova TABLE"). Die neue Dichtung leicht einölen und
guarnizione e montare un nuovo einen neuen Filter mit den gleichen
Eigenschaften
filtro di uguali caratteristiche vedi montieren; siehe ("TABELLE DER FIL-
("TABELLA ELEMENTI FILTRANTI E TERELEMENTE UND KEILRIEMEN").
CINGHIE").
2
1
C17 C17/1 C17/2
5
4
C17/3 C17/4
24
Posizionare il carrello su di una superficie Place the truck on a horizontal Teleskoplader auf einerebenen Fläche
orizzontale con il motore fermo. surface and turn the engine off. abstellen. Motor abstellen.
Effettuare un controllo visivo del fissaggio Visually check the fixing screws of the Führen Sie eine Sichkontrolle der
delle viti della ralla di rotazione al telaio bearing to the frame 1 (fig. C18) and Befestigung desDrehkranzes am
1 (fig.C18) e alla torretta 2 (fig.C18). to the turret 2 ( fig. C18). Fahrgestell 1 (fig.C18) und Oberwagen 2
Nel caso in cui si notino anomalie con- In the case that irregularities are seen (fig.C18) durch. Wenden Sie sich an
sultate il vostro agente o concessionario. consult your AGENT OR DEALER. Ihren Vertragshändler .
Posizionare il carrello su di una Place the truck on a horizontal surfa- Den Teleskoplader auf einer ebenen
superficie orizzontale con il motore ce with off engine and the telescopic Fläche abstellen.Motor abstellen.
fermo ed il braccio telescopico boom completly lifted . Teleskop vollständig angehoben.
completamente sollevato. Effettuare un Effectuate a visible checking of the Führen Sie eine
controllo visivo del fissaggio delle viti del fixing screw of the rotation reducer at Sichtkontrolle der Befestigung des
riduttore di rotazione al telaio 3 frame 3 (fig. C19). Untersetzungsgetriebes am Fahrgestell
(fig.C19). Nel caso in cui si notino ano- In the case that irregularities are seen 3 (Abbildung C19) durch.
malie consultate il vostro agente o con- consult your AGENT OR DEALER. Wendes Sie sich an Ihren
cessionario.
Vertragshändler.
C18
400° 360°
3
3
C19
25
D - OGNI 500 ORE DI MARCIA D - EVERY 500 HOURS SERVICE D - ALLE 500 BETRIEBSSTUNDEN
D 1 - Luftfiltereinsatz ersetzen
D 1 - Sostituire cartuccia filtro aria D 1 - Replace the air filter cartridge
Die Ansaugluft des Motors, wird in
L’aria che viene aspirata dal motore è filtrata The air used to burn the fuel is purified einem Trockenluftfilter gereinigt.
da un filtro ad aria secca; è molto importante by a dry air filter. The lift truck should Daß das Fahrzeug nie mit einem
beschädigten oder ohne Luftfilter
non utilizzare il carrello elevatore senza il filtro never ever be used if the air filter has verwenden.
dell’aria o col filtro danneggiato. been removed or is damaged. Mutter "1" (Abb. D1/1) entfernen,
Svitare il dado 1 (fig.D1/1), togliere il coperchio Slacken nut 1 (fig. D1/1), remove cover den Deckel "2" (Abb. D1/1) abneh-
2 (fig.D1/1). men.
2 (fig. D1/1). Dann die Mutter "3" (Abb. D1/2), die
Quindi svitare il dado 3 (fig.D1/2) che fissa la Now unscrew nut 3 (fig. D1/2) that fixes den Filtereinsatz "4" (Abb. D1/2)
cartuccia filtrante 4 (fig.D1/2) e toglierla. Pulire filtering cartridge 4 (fig. D1/2), remove sichert entfernen.
l’interno del filtro con un panno umido, pulito e Den Filtereinsatz herausnehmen
this latter and discard. und umweltgerecht entsorgen.
che non lasci residui. Clean the inside part of the filter with a Das Filtergehäuse mit
damp, clean lint-free cloth. einem sauberen,feuchteten und
fuselfreien Lappen reinigen.
Pulire con cura l’esterno del filtro e del D 2 - Replace the fuel filter cartridge D 2 - Kraftstofffilterpatrone wechseln
supporto per impedire l’ingresso della
polvere nel sistema. Allentare la vite di Filter und Halterung außen jeweils
Carefully clean the outside part of the fil-
scarico 1 (fig.D2) alla base del filtro e sorgfältig reinigen, damit keine
ter and bracket to prevent dust from
scaricare l’acqua e il combustibile Schmutzpartikel ins System gelangen.
penetrating the system.
raccogliendoli dentro un contenitore. Ablassschrauben 1 (ABB. D2) unten am
Slacken outlet 1 (fig. D2) at the end of
Smontare il filtro 2 e poi la cartuccia 3 Filter lösen; Wasser und Kraftstoff in
the filter and drain off the water and fuel,
dalla sua sede ruotandola in senso einem geeigneten Behälter auffangen.
collecting this in a receptacle.
antiorario. Den Filter 2 und dann den Filtereinsatz
Remove filter 2 and then cartridge 3
Montare l'elemento filtrante nuovo 3, 3 aus seiner Aufnahme ausbauen,
from its seat by turning it clockwise. indem man ihn im Gegenuhrzeigersinn
inserendolo nella sua sede e ruotarlo di
Fit the new filter element 3, inserting it in dreht.
90° in senso orario. Avvitare il filtro 2 e
its seat and turning it through 90° Das neue Filterelement 3 montieren und
la cartuccia 3 fino a ché non entrano in
clockwise. Fit filter 2 and cartridge 3 till es in seine Aufnahme stecken, um es
contatto con la testa 4, a questo punto
they make contact with head 4, and then dann um 90° im Uhrzeigersinn zu
girare ancora di 1/2 giro.
rotate through another half-turn. drehen. Den Filter 2 und den
Filtereinsatz 3 anschrauben, bis sie den
Kopf 4 berühren, um sie dann noch um
1/2 Umdrehung zu drehen.
D2
2
1
D1/1
2 3
1
3
4
1 2
D1/2
26
Prima di riavvitare il coperchio del filtro 1 Before fitting the cover of filter 1 back on Vor dem erneuten Festschrauben des
(fig.D4), controllare che la cartuccia sia (fig. D4), check that the cartridge has Filterdeckels "1" (Abb. D4) sicherstellen,
montata correttamente. been correctly installed. daß der Filtereinsatz korrekt montiert ist.
D 5 - Pulire sfiato olio idraulico e D 5 - Replace the hydraulic and D 5 - Entlüftungsfilter Hydrauliktank
trasmissione transmission oil vent ersetzen
Svitare lo sfiato 1 (fig.D5) sul serbatoio Unscrew vent 1 (fig. D5) on the oil tank Die Entlüftungsvorrichtung "1" (Abb. D5)
olio e sostituirlo con uno nuovo di uguali and replace it with a new one see auf dem Ölbehälter loschrauben und
caratteristiche vedi ("TABELLA ELE- ("SCHEDULE MAINTENNCE"). durch eine neue ersetzen.
MENTI FILTRANTI E CINGHIE"). Die neue Entlüftung von Hand fest-
Screw on the new vent by hand. drehen.
Montare il nuovo sfiato serrandolo a Alten Filter umweltgerecht entsorgen.
mano.
D3
Ø
Ø Ø
Ø
1 1
2
D4 D5
27
D 6 - Sostituire filtro in mandata D 6 - Replace main circuit delivery filter D 6 - Filter in Druckleitung des
circuito principale Hauptkreislaufs ersetzen
Il filtro 1 (fig.D6/1) è munito di un Filter 1 (Fig.D6/1) is provided with a clog- Der Filter 1 (Abb. D6/1) ist mit einer
indicatore 6 (fig.D6/1) di intasamento ging indicator 6 (Fig.D6/1) which turns "red" Verstopfungsanzeige 6 (Abb. D6/1) ver-
che indica “rosso” quando la cartuccia when the oil filter cartridge 4 (Fig.D6/4) is sehen, die "rot" anzeigt, wenn die
filtro olio 4 (fig.D6/4) è intasata. blocked. Filterpatrone 4 (Abb. D6/4) verstopft ist.
La cartuccia 4 (fig.D6/4) si trova all’inter- Cartridge 4 (Fig.D6/4) is located inside filter Die Filterpatrone 4 (Abb. D6/4) befindet
no del filtro 1 (D6/1) e per sostituirla 1 (D6/1). To replace it, proceed as follows: sich innerhalb des Filters 1 (D6/1). Um
occorre: -Unscrew filter body 2 (Fig.D6/2) using a sie zu ersetzen, ist folgendes
-Svitare il corpo filtro 2 (fig.D6/2) con spanner and remove it 3 (Fig.D6/3) from erforderlich:
una chiave e smontarlo 3 (fig.D6/3) filter head 5 (Fig.D6/4). -Den Filterbecher 2 (Abb. D6/2) mit
dalla testata del filtro 5 (fig.D6/4). -Remove cartridge 4 (Fig.D6/4) from filter einem Schlüsse losschrauben und vom
- Estrarre la cartuccia 4 (fig.D6/4) dalla head 5 (Fig.D6/4) and replace with a new Filterkopf 5 (Abb. D6/4).
testata del filtro 5 (fig.D6/4) e sostituirla D6/5 one. abnehmen 3 (Abb. D6/3).
con una nuova D6/5. -Now fit filter body 2 (Fig.D6/2) back on to - Die Filterpatrone 4 (Abb. D6/4) aus dem
- Infine riavvitare bene il corpo filtro 2 head 5 (Fig.D6/4) and start up the truck to Filterkopf 5 (Abb. D6/4) herausnehmen
(fig.D6/2) alla testata 5 (fig.D6/4) e check for leakage. (Check filter efficienc und durch eine neue (Abb. D6/5)
avviare il carrello e controllare che non periodically by means of indicator ersetzen.
ci siano perdite. (Controllare periodica 6 Fig.D6/1). -Schließlich den Filterbecher 2 (Abb.
mente l’efficacia del filtro mediante D6/2) wieder am Filterkopf 5
l’indicatore 6 fig.D6/1). (Abb. D6/4) anschrauben und den
Teleskopstapler starten, um ihn auf
Leckstellen zu prüfen.
(Filter regelmäßig auf
Funktionstüchtigkeit prüfen, und zwar
mittel Anzeige 6 Abb. D6/1).
6
1
D6/4 D6/5
28
E - OGNI 1000 ORE DI MARCIA E - EVERY 1000 HOURS SERVICE E - ALLE 1000 BETRIEBSSTUNDEN
E 1 - Sostituire olio idraulico e E 1 - Change the hydraulic and E 1 - Hydrauliköl wechseln
trasmissione transmission oil
Fahrzeug auf ebener Fläche abstellen.
Prima di fare queste operazioni, assicu- Before proceeding with these opera- Motor abstellen.
ratevi che il carrello sia su di una super- tions, check that the truck is standing on Einen geeigneten Auffangbehälter
ficie orizzontale e che il motore sia a unter dem Ölablaßstopfen "1" (Abb.
spento. Mettere un recipiente sotto il perfectly horizontal surface and that the E1/1) stellen. Den Stopfen abschrauben
tappo di svuotamento 1 (fig. E1/1.). engine is off. und das Öl auslaufen lassen.
Togliere il tappo e lasciare defluire l’olio. Place a receptable under drain plug 1 Auch den Öleinfüllstopfen "2" (Abb.
Per affrettare lo svuotamento, togliere il (fig. E1/1). E1/2) öffnen, damit das Öl
tappo di riempimento 2 (fig.E1/2). Remove the plug and allow the oil to schneller ausläuft.
Altöl umweltgerecht entsorgen.
Quando il serbatoio sarà vuoto smonta- flow out. Wenn der Ölbehälter
re il filtro dell’olio idraulico togliendo le Remove fill plug 2 (fig. E1/2) to speed leer ist, den Hydraulikfilter ausbauen,
quattro viti di fissaggio 4 (fig.E1/3) al up the operation. indem man die vier
serbatoio per accedere alla succhieruola When the tank is empty, remove the Befestigungsschrauben
d’aspirazione. hydraulic oil filter by unscrewing the four "4" (Abb. E1/3) am Ölbehälter löst,
fixing screws 4 (fig.E1/3) for access to um Zugriff zum Saugkorb zu erhalten.
the suction cartridge.
Svitare la cartuccia di aspirazione situa- Unscrew the cartridge from the bottom Den Saugkorb am Boden des Ölbehäl-
ta sul fondo del serbatoio ,e sostituirla of the tank, replace with a new one. terslosschrauben, mit Dieselöl
con una di uguali caratteristiche vedi Filling the tank reinigen und mit Druckluft säubern. Den
("TABELLA ELEMENTI FILTRANTI E Refit and tighten drain plug 1 (fig. E1/1). sauberen Saugkorb wieder einbauen.
CINGHIE"). Fill the tank with oil (see “LUBRICANT” Füllen des Hydrauliktank
Den Ölablaßstopfen "1" (Abb. E1/1)
Riempire del serbatoio. chart) through fill hole 5 (fig. E1/2) until einsetzen und festschrauben.
Rimettere e serrare il tappo di the oil level reaches between the lower Den Ölbehälter durch den Öleinfüllstop-
svuotamento 1 (fig.E1/1).Riempire il and upper marks of level gauge 6 (fig. fen "5" (Abb. E1/2) füllen (vgl. “TABEL-
serbatoio d’olio (vedere "LUBRIFICAN- E1/4). LE DERFÜLLMENGEN”), bis der korrek-
TI”) attraverso il foro di riempimento 5 Check for any leaks from the drain hole. te Ölstand erreichtist. (zwischen den
(fig.E1/2) fino a quando il livello dell’olio Refit tank plug 2 (fig. E1/2). beiden Markierungen des
non é equidistante fra i segni di Ölstandanzeigers "6" (Abb. E1/4)
riferimento inferiore e superiore Die Ölablaßschraube auf festen Sitz und
Dichtheit prüfen.
dell’indicatore di livello 6 Die Verschlußschraube des Ölbehälters
(fig.E1/4).Controllare eventuali perdite "2" (Abb. E1/2) aufsetzen.
dal foro di svuotamento. Mettere il tappo
di chiusura del serbatoio 2 (fig.E1/2).
5
1
E1/1 E1/2
E1/3 E1/4
29
E 3 - Sostituire olio differenziale E 3 - Change the oil in the front and E 3 - Differentialöl der Vorder und
assale anteriore e posteriore rear axle differential Hinterachse ersetzen
Posizionare il carrello su di una superfi- Put the truck on a horizontal surface Das Fahrzeug auf ebener Fläche abstel-
cie orizzontale con il motore fermo e l’o- with the engine off and the differential oil len.
lio del differenziale ancora caldo. still warm. Motor abstellen.
Porre una recipiente sotto i tappi di Drain the oil from the front axle Achten Sie auf Betriebstemperatur der
svuotamento 2(fig.E3) e lasciare defluire differential. Achsen.
l’olio. Togliere il tappo di livello 3 (fig.E3) Place a can under drain plugs 1 (fig. E3) Differentialöl der Vorderachse ablassen.
e il tappo di riempimento 1 (fig.E3) per and allow the oil to drain out. Einen geeigneten Auffangbehälter unter
assicurare uno svuotamento completo. Remove level plug 2 (fig. E3) and fill dieÖlablassstopfen "1" (Abb. E3) stellen
Rimettere e stringere i tappi 2 (fig.E3). plug 3 (fig. E3) to ensure that all oil und das Öl abfließen lassen. Den
Mettere l’olio (vedere ”LUBRIFICANTI”) drains out. Ölstandsstopfen "2" (Abb. FE3) und den
attraverso il foro di riempimento 1 Refit and tighten plugs 1 (fig. E3). Öleinfüllstopfen "3" (Abb. E3) ebenfalls
(fig.E3). Il livello è corretto quando l’olio Fill with oil (see “LUBRICANT” chart) öffnen, damit das Öl schneller abfließt.
affiora al foro di livello 3 (fig.E3). through fill hole 3 (fig. E3). Die Stopfen "1" (Abb. E3) wieder ein-
Controllare eventuali perdite dai tappi di The level is correct when the oil reaches setzen und festziehen.
svuotamento. Rimettere e stringere il the top of level hole 2 (fig. E3). Durch die Öleinfüllstopfen "3" (Abb. E3)
tappo di livello 3 (fig.E3) e il tappo di Check for any leaks from the drain neues Öl einfüllen (vgl. “TABELLE DER
riempimento 1 (Fig. E3). Effettuare la plugs. FÜLLMENGEN”). Der Füllstand ist kor-
stessa operazione per il differenziale Refit and tighten level plug 2 (fig. E3) rekt, wenn das Öl bis zur Standschraube
togliere i tappi posteriore. and fill plug 3 (Fig. E3). "2"
Repeat these operations for the rear (Abb. E3) reicht. Die Ölablaßstopfen auf
axle. Dichtheit prüfen prüfen. Den Ölstands-
stopfen "2" (Abb. E3) und den Öleinfüll-
stopfen "3" (Abb. E3) einsetzen und
festziehen. Den gleichen Vorgang an
der
Hinterachse wiederholen.
Altöle umweltgerecht entsorgen.
E 4 - Sostituire olio riduttore E 4 - Changing oil in front and rear E 4 - Öl der vorderen und hinteren
ruote anteriore e posteriore wheel final drives Endantriebe ersetzen
3
B
E3 E4
30
Posizionare il carrello su di una Set the truck on a horizontal surface Das Fahrzeug auf ebener Fläche abstel-
superficie orizzontale con il motore with the engine off and the oil in the len.
fermo e l’olio del riduttore ancora caldo. reduction gear still hot. Place a recepta- Motor abstellen.
Porre un recipiente sotto al tappo di cle under drain plug 1 (fig. E5). Remove Achten sie auf Betriebstemperatur des
svuotamento 1(fig.E5). Togliere il tappo plug 1 and allow the oil to drain out. Untersetzungsgetriebes.
1 e lasciare defluire Remove fill and level plug 1 (fig. E5) to Einen geeigneten Auffangbehälter unter
den Ölablaßstopfen "1" (Abb. E5) stellen.
l’olio. Togliere il tappo di livello e ensure that all oil has drained out. Refit
Stopfen "1" abschrauben und das Öl
riempimento 1 (fig.E5) per assicurare and tighten plug 1 (fig. E5). Fill with oil
ausfließen lassen.
uno svuotamento completo. Rimettere e (see “LUBRICANT” chart) through fill Den Ölstands- und Öleinfüllstopfen "2"
serrare il tappo 1 (fig.E5). Mettere l’olio and level plug 1 (fig. E5). The level is (Abb. E5) abschrauben, damit das Öl
(vedere “LUBRIFICANTI”) attraverso il correct when flush with the top of the besser ausläuft.
foro di livello e riempimento 1 (fig.E5). Il hole. Den Stopfen "1" (Abb. E5) einsetzen
livello é corretto quando l’olio affiora dal Refit and tighten fill and level plug 1 (fig. und festziehen.
foro. E4). Durch den Ölstands- und Öleinfüllstop-
Rimettere e stringere il tappo di livello e Check for any leaks from the drain plug. fen "2" (Abb. E5) neues Öl einfüllen (vgl.
riempimento 1 (fig.E5) “TABELLE DER FÜLLMENGEN”).
Controllare eventuali perdite dal tappo di Der Ölstand ist korrekt, wenn das Öl aus
svuotamento. der Öffnung austritt.
Den Ölstands- und Öleinfüllstopfen "2"
(Abb. E5) einsetzen und festziehen.
Den Ölablaßstopfen auf Dichtheit prüfen.
Altöle umweltgerecht entsorgen.
E 6 - Sostituire cartuccia di sicurezza E 6 - Change the air filter safety E 6 - Ersetzen der Sicherheitspatrone
del filtro dell’aria cartridge des Trockenluftfilters.
Smontare la cartuccia del filtro dell'aria Remove the air filter cartridge (see chap- Den Luftfiltereinsatz (siehe Kap. : D 1 )
(vedi capitolo: D 1 ). ter: D 1 ). ausbauen.
Togliere la cartuccia di sicurezza del filtro Remove the air filter safety cartridge “1” Die Sicherheitspatrone des Luftfilters "1"
dell'aria "1" (fig.E6) e sostituirla con una (fig. E6) and replace it with a new one. (Abb.E6) herausnehmen und durch eine
nuova. Reassamble the kit (see chapter: D 1 ). neue ersetzen.
Rimontare la cartuccia del filtro dell'aria Zusammenbau in umgekehrter
(vedi capitolo: D 1 ). Reihenfolge.
Altfilter umweltgerecht entsorgen.
(siehe Kap. : D 1 ).
E5 E6
31
E 8 - Keilriemen wechseln.
E 8 - Sostituire cinghia alternatore E 8 - Changing the alternator
belt/crankshaft
Posizionare il carrello su di una superficie Den Teleskoplader auf ebenenr Fläche
piana e con il motore fermo. Place the truck on a flat surface with the abstellen.
Svitare la vite di fissaggio dell'alternato- engine off. Motor abstellen.
Loosen the connection screw of alterna- Die Befestigungsschrauben der
re 1 e la vite di fermo della leva
Lichtmaschine 1 und die Spannschraube
tendicinghia 2 (Fig. E8) di 2 o 3 giri di tor 1 and the set screw of the belt ten-
des Spannerhebels 2 (Abb. E8) ca. 2
filetto e ruotare la posizione sioner lever 2 (Fig. E8) by 2 or 3 thread oder 3 Umdrehungen lösen.
dell'alternatore in modo da allentare la turns and rotate the position of the alter- Keilriemen entfernen und durch einen
tensione della cinghia per estrarla dalle nator to loosen the tension of the belt so neuen Keilriemen ersetzen.
pulegge. Sostituire la cinghia con una di that it can be removed from the pulleys. (siehe “FILTER UND
uguali caratteristiche,(vedi "TABELLA Replace the belt with another one with KEILRIEMENTABELLE”), die
ELEMENTI FILTRANTI E CINHIE"), ruo- similar features (see “FILTERING ELE- Lichtmaschinenposition ausrichten, um
tare la posizione dell'alternatore per MENT AND BELT TABLE”) and rotate dem Keilriemen die korrkete Spannung
dare alla cinghia la tensione corretta. the position of the alternator to apply the zugeben.Die Spannschraube
Serrare la vite di fermo del tendicinghia correct tension to the belt. 2 (Abb. E8) und die
2 (Fig. E8) e le viti di fissaggio dell'alter- Tighten the set screw of the belt tensio- Befestigungsschrauben der
natore 1(Fig. E8). Controllare nuova- ner 2 (Fig. E8) and the alternator con- Lichtmaschine 1 (Abb. E8) festziehen.
mente la tensione della cinghia per assi- nection screws 1(Fig. E8). Nochmals die Spannung des
curarsi che sia ancora Check the belt tension again to make Keilriemens prüfen, um sicherzustellen,
sure it is still correct. daß sie korrektist.
corretta. E' consigliato un ulteriore
Nach ca.20 Betriebsstunden, die
controllo della tensione della cinghia It is recommended to check the belt ten-
Keilriemenspannung erneut überprüfen
dopo 20 ore di lavoro dalla sostituzione sion again after 20 hours of service from (siehe Vorgang Nr. C1).
(vedere operazione n°C1). when the belt was replaced (see opera-
tion no. C1).
2
'
1
E7/1 1 E8
32
Posizionare il carrello, con torretta Position the lift truck, with turret aligned, on a Den Teleskopstapler mit ausgerichtetem
allineata, su di una superficie piana, level surface, Turm auf eine ebene Fläche stellen, den
rientrare e sollevare completamente il retract and raise telescopic boom completely, Teleskopausleger ganz einfahren und
braccio telescopico e poi ruotare la heben und den Turm dann um +/- 60°
and then turn the turret to the right by
torretta a destra di +/- 60°, per accedere nach rechts drehen, um besseren Zugriff
+/- 60°, for better access to the rotation
meglio ai punti di riempimento del zu den Einfüllstellen des
riduttore rotazione (fig.E9); fermare il reduction gear filling points (Fig.E9).
Rotationsgetriebes (Abb. E9) zu
motore termico e attendere che si Stop the I.C. engine and wait for the hydraulic erhalten; den Motor abstellen und
raffreddi l’olio idraulico. oil to cool down. abwarten, dass das Öl sich abkühlt.
Per la sostituzione dell’olio porre un To change the oil in the top part, place a Zum Wechseln des Öls im oberen Teil
recipiente sotto il tappo di scarico princi- suitable vessel under the main drain einen geeigneten Auffangbehälter unter
pale 1 (fig.E9/1), allentarlo e lasciare plug 1 (fig.E9/1), loosen this latter and den Hauptablassstopfen 1 (Abb. E9/1)
defluire l’olio. Rimettere e stringere il allow the old oil to drain out. Fit the stellen, Ablassstopfen entfernen und das
tappo di scarico 1 (fig.E9/1). Eseguire il drain plug 1 (fig.E9/1) back on and tigh- Öl ablaufen lassen.
riempimento attraverso il foro 2 ten it. Pour in new oil through hole 2 Den Ablassstopfen 1 (Abb. E9/1)
(fig.E9/1) (vedi “Lubrificanti”). Il livello é (fig.E9/1) (see “Lubricants”). The level wieder einsetzen und festziehen.
corretto quando l’olio affiora e defluisce is correct when the oil spills from hole 3 Das Einfüllen erfolgt durch die Öffnung 2
dal foro 3 (fig.E9/1). (fig.E9/1). (Abb. E9/1) (siehe "Schmierstoffe"). Der
Füllstand des Öls ist richtig, wenn das
Öl die Öffnung 3 (Abb. E9/1)
erreicht und austritt.
E9
3
1
3
MAX 1 3
2
MIN 2
E9/1
33
E9a
1 1
2
2
3
4
E9a/1
34
Qualora la sostituzione della ruota In the event of a wheel being changed Sollte ein Rad auf öffentlichen
dovesse essere effettuata lungo la stra- on the public highway, make sure of Verkehrswegen gewechselt werden, fol-
da, procedere come descritto qui the following points : genden Punkten beachten :
di seguito:
- Se possibile fermare il carrello elevatore - Stop the lift truck, if possible on even - Wenn möglich, den Teleskoplader auf
in piano su un terreno compatto. and hard ground. festem, waagerechtem Boden
- Spegnere il carrello elevatore (Vedi - To pass on stop of lift truck (See chap- abstellen.(Siehe
capitolo: ISTRUZIONI DI GUIDA nella ter : DRIVING INSTRUCTIONS in Kapitel : FAHRANWEISUNGEN,
parte: 1 - ISTRUZIONI E NORME DI paragraph : 1 - OPERATING AND Abschnitt : 1 - ANWEISUNGEN UND
SICUREZZA). SAFETY INSTRUCTIONS). SICHERHEITSVORSCHRIFTEN).
- Attivare il freno di stazionamento - Action the parking brake - Warnblinkanlage einschalten.
- Accendere le luci di emergenza. - Put the warning lights on. - Fahrzeug gegen den Fließenden
- Applicare cunei per immobilizzare il - Immobilise the lift truck in both direc- Verkehr absichern
carrello elevatore nelle due direzioni tions on the axle opposite to the wheel - Den Teleskoplader in beiden
sull’assale opposto alla ruota da to be changed. Richtungen
sostituire. - Unlock the nuts of the wheel to be auf der dem zu wechselnden Rad
- Allentare i bulloni dalla ruota da changed. gegenüberliegenden Achse verkeilen.
sostituire - Place the jack under the flared axle - Radmuttern des zu wechselnden
- Sistemare il cric sotto la semiscatola tube, as near as possible to the wheel Radeslösen.
dell’assale, il più vicino possibile alla and adjust the jack (Fig. H1/1). - Den Wagenheber so nahe wie möglich
ruota e regolare il cric (Fig. H1/1). - Lift the wheel until it comes off the am Rad unter den Achstrichter stellen
- Sollevare la ruota fino a staccarla da ground and put in place the safety sup- und ausrichten (Abb. H1/1).
terra e posizionare il sostegno di port under the axle (Fig. H1/2). - Das Rad anheben, bis es vom Boden
sicurezza sotto l’assale (Fig. H1/2). abhebt und die Sicherheitsstütze unter
der Achse anbringen (Abb. H1/2).
Per effettuare questa operazione, vi con- For this operation, we advise you to use Für diese Arbeit empfehlen wir den
sigliamo di utilizzare un cric idraulico e il the hydraulic jack and the safety sup- Einsatzeines hydraulischen
sostegno di sicurezza. port. Wagenhebers und einer
Sicherheitsstütze (Unterstellbock).
- Svitare completamente i bulloni delle
ruote e rimuoverli. - Completely unscrew the wheel nuts - Die Radmuttern entfernen.
- Estrarre la ruota con movimenti di va e and remove them. - Das Rad demontieren .
vieni e ruotarla sul lato. - Free the wheel by reciprocating move- - Das neue Rad montieren.
- Mettere la ruota nuova sul mozzo. ments and roll it to the side. - Die Radmuttern von Hand
- Avvitare manualmente i bulloni, se - Slip the new wheel on the wheel hub. festschrauben, gegebenenfalls
necessario lubrificarli con del grasso. - - Refit the nuts by hand, if necessary schmieren.
Stringere a fondo i bulloni delle ruote grease them.
con una chiave dinamometrica - Remove the safety support and lower
- Rimuovere il sostegno di sicurezza e the lift truck with the jack.
abbassare il carrello elevatore con il - Tighten the wheel nuts with a torque
cric. wrench (See chapter : A - DAILY OR
(Vedi capitolo: A - OGNI GIORNO O EVERY 10 HOURS SERVICE in para-
OGNI 10 ORE DI MARCIA nella graph : 3 - MAINTENANCE for tighte-
parte:3 MANUTENZIONE, per la ning torque).
coppia di serraggio).
H1/1 H1/2
35
Il traino può esser effettuato a velocità To the lift truck for short distance with Der Teleskoplader darf nur bei stark ver-
molto ridotta e per brevi distanze. slow speed. ringerter Fahrgeschwindigkeit und nur
über kurze Strecken abgeschleppt wer-
den.
- Mettere la leva dell’invertitore di marcia - Shut down engine
in folle. - Put the forward/reverse lever in neutral - Fahrtrichtungswahlhebel auf Neutral.
- Disinserire il freno di stazionamento. position - Feststellbremse lösen.
- Accendere le luci di emergenza. - Release the parking brake - Warnblinkanlage einschalten.
- posizionare manualmente il cambio in - Put the emergency lights - Gangwahlhebel von Hand in die
posizione di folle: - put the gear selector in neutral position: Leerlaufstellung betätigen:
a) scollegare e tappare i tubi idraulici a) disconnect and close the hydraulic a) Hydraulikleitungen (Nr.1 ABB. H2/1)
(Rif.1 Fig.H2/1) dal martinetto della (Rif.1 Fig.H2/1) of the cylinder of the von Anschluss am Langsam/Schnell-
scatola del cambio marcia lenta/mar gear selector. Getriebegehäuse lösen und mit
cia veloce; b) put the rod (Rif.2 Fig.H2/1) in neutral Stopfen verschließen.
b) fare leva sullo stelo (Rif.2 Fig.H2/1) position (this is on half sroke between b) Einen Hebel an der Stange (Nr. 2
della scatola del cambio per farlo two “release”) ABB. H2/1) des Getriebegehäuses
ansetzen und Stange nach außen in
uscire e portarlo in posizione neutra
die Neutralstellung drücken
(posizione intermedia fra i due “scatt - Deactivate the negative brake: (Zwischensstellung zwischen den bei
successivi); c) screw the screws with lock nut den nacheinander folgenden
(Rif.1 Fig.H2/2 e Rif.1 Fig.H2/3) "Rasten").
- Disattivare il freno negativo: placed on both sides of the front axle
box until they touch of the rod. Now - Negativbremse lösen:
c) avvitare le viti con controdado
(Rif.1 Fig.H2/2 e Rif.1 Fig.H3/3) screw the same one turn.
c) Schrauben mit Kontermuttern (Nr. 1
posizionate ai due lati della scatola ABB. H2/2 und Nr. 1 ABB. H2/3) auf
dell’assale anteriore fino al loro - If the engine is not running there will
beiden Seiten des
appoggio con il pistone. A questo be no steering or braking assistance. Vorderachsgehäuses eindrehen, bis
punto effettuare una rotazione di un Operate the steering and pedal slowly sie am Kolben aufliegen.
giro. avoiding sudden jerky movements. Nun eine weitere Umdrehung
ausführen.
- In assenza della servoassistenza
idraulica alla direzione e ai freni, agire - Da die hydraulischen Lenk- und
lentamente e con energia su questi Bremshilfen jetzt abgeschaltet sind,
due comandi. Evitare i movimenti Lenkung und Bremse nur langsam und
bruschi e gli scatti. mit hohem Kraftaufwand zu betätigen.
Abrupte und ruckartige Betätigung sind
zu vermeiden.
È importante che le viti contrapposte It’s important that the two screws have Es ist wichtig, dass die beiden gegenü-
siano avvitate della stessa quantità. the same turns. berliegenden Schrauben jeweils mit der
gleichen Anzahl an Umdrehungen fest-
gezogen werden.
1
1
1 1
2
- Tenere conto della posizione del centro - Take into account the position of the lift - Den Schwerpunkt des Gabelstaplers
di gravità del carrello elevatore per il truck gravity center for lifting (Fig. zum Anheben berücksichtigen (Abb.
sollevamento (Fig. H3/1). H3/1). H3/1).
- Posizionare le fascie nelle sedi di - Place the hooks in the fastening points -ausreichend tragfähige Lastaufnahme
ancoraggio previste (Fig. H3/2 e provided (Fig. H3/2 and H3/3). mittel verwenden.
H3/3). - Hebegeschirr an den Anschlagpunkten
befestigen. (Abb. H3/2 und H3/3).
MRT 1432
H4/1
H4/2 H4/3
1 1 2 2
37
Controllare la corretta applicazione delle Ensure that the safety instructions con- Vor dem Verladen des Teleskopladers
istruzioni di sicurezza relative alla piat- nected to the platform are respected auf die Anwendung der
taforma di trasporto prima di caricare il before the loading of the lift truck and Sicherheitsanweisungen achten.
carrello elevatore, e verificare che il con- that the driver of the means of tran- Den Fahrer des Transportes über die
duttore del mezzo di trasporto sia infor- sport is informed about the dimensions Abmasse und das Gewicht der Ladung
mato delle caratteristiche dimensionali e and the weight of the lift truck (See informieren.
del peso del carrello elevatore (Vedi chapter : CHARACTERISTICS in para- (Siehe Kapitel : TECHNISCHE DATEN,
capitolo: CARATTERISTICHE TECNI- graph : 2 - DESCRIPTION). Abschnitt : 2 - BESCHREIBUNG)
CHE nella parte 2 - DESCRIZIONE).
Accertarsi che la piattaforma abbia delle Ensure that the platform has got Bei Teleskopladern, die mit einem
dimensioni e una capacità di carico suffi- dimensions and a load capacity suffi- Turbolader ausgerüstet sind, den
cienti per trasportare il carrello elevato- cient for transporting the lift truck. Auspuff verschließen, damit der
re. Controllare anche la pressione di Check also the pressure on the contact Turbolader nicht durch eindringenden
contatto al suolo autorizzata per la piat- surface allowable for the platform in Fahrtwind angetrieben wird.
taforma rispetto al carrello elevatore. connection with the lift truck. ( FEHELNDE SCHMIERUNG)
- Bloccare le ruote della piattaforma di - Block the wheels of the platform. - Die Räder des Sattelaufliegers
trasporto. - Fix the loading ramps so that you blockieren.
- Fissare le rampe di carico alla obtain an angle as little as possible to - Die Laderampen am Sattelauflieger
piattaforma, in modo da ottenere un lift the lift truck. befe stigen, mit einem möglichst gerin
angolo il più piccolo possibile per far - Load the lift truck parallel to the gen Winkel.
salire il carrello elevatore. platform. - Den Teleskoplader parallel zum
- Caricare il carrello elevatore - Stop the lift truck (See chapter : DRI- Sattelauflieger laden.
parallelamente alla piattaforma. VING INSTRUCTIONS in paragraph : -Teleskoplader abstellen (Siehe Kapitel :
- Spegnere il carrello elevatore (Vedi 1 - OPERATING AND SAFETY FAHRANWEISUNGEN, Abschnitt : 1 -
capitolo: ISTRUZIONI DI GUIDA nella INSTRUCTIONS). ANWEISUNGEN UND
parte: 1 - ISTRUZIONI E NORME DI SICHERHEITSVORSCHRIFTEN).
SICUREZZA).
H5/1
38
1 2
H5/3 H5/4
+%
-%
-2%
h1
h2
I
H6
39
Il motorino d’avviamento é montato sulla The starter motor is mounted on the Der Anlasser ist auf der linken
sinistra del motore e non è richiesta left-hand side of the engine. No Motorseite montiert und wartungsfrei. Er
altra manutenzione se non quella della maintenance is required other than muß nur gereinigt werden und die
pulizia e del serraggio dei morsetti. Se il to ensure that the terminals are Befestigung der Klemmen ist zu prüfen.
motorino d’avviamento non funziona kept clean and well tightened. Wenn der Anlasser nicht richtig funktio-
bene, Consult your agent or dealer if the niert, wenden Sie sich an den
consultate il Vostro agente o starter motor fails to operate correc- Vertragshändler oder die Vertretung.
concessionario. tly.
Lichtmaschine
Alternatore Alternator
Die Lichtmaschine ist links vom Motor
L’alternatore é montato sulla sinistra del The alternator is installed on the montiert. Lichtmaschine und Regler sind
motore. L’alternatore e il regolatore sono left-hand side of the engine. The so konzipiert, daß sie nur in einem
studiati per funzionare in un sistema alternator and regulator are desi- System arbeiten, das in einer Richtung
polarizzato in un solo senso, perciò è gned to operate in a system which polarisiert ist. Daher sind die folgenden
necessario prendere le precauzioni is polarized in one direction only. It Vorsichtsmaßnahmen zu treffen, wenn
seguenti quando si lavora sul circuito di is therefore necessary to take the man am Batterieladekreis arbeitet, weil
carica della batteria, altrimenti si posso- following precautions when working die elektrische Anlage sonst Schaden
no causare gravi danni alle apparecchia- on the battery charging circuit, nehmen kann: Die Lichtmaschine nicht
ture elettriche: otherwise serious damage may be bei offenem Stromkreis betätigen, son-
Non azionare l’alternatore con circuito caused to the electrical equipment: dern
aperto, ma assicurarsi che tutti i morsetti Do not operate with an open circuit. sicherstellen, daß alle Klemmen fest
siano serrati bene. E’ importante non Always ensure that all terminals are angezogen sind. Die Klemmen auf der
smontare i morsetti posti sul retro well tightened. Never demount the Rückseite der Lichtmaschine dürfen
dell’alternatore mentre il motore termico terminals at the rear of the alterna- nicht abgenommen werden, während
gira, per evitare di danneggiare tor while the engine is running der Motor läuft, weil die Lichtmaschine
l’alternatore stesso. Quando si installa otherwise the alternator will be sonst
una batteria, assicurarsi che i collega- damaged. beschädigt würde.
menti siano polarizzati correttamente. E’ When a battery is installed, ensure Wenn man die Batterie einbaut,
essenziale che il cavo contrassegnato that the connections are correctly sicherstellen, daß die Anschlüsse wie
da (+) sia collegato al terminale positivo polarized. It is essential for the vorgeschrieben polarisiert sind. Das mit
(+) della batteria e che il cavo contras- cable marked (+) to be connected to (+) gekennzeichnete Kabel muß unbe-
segnato da (-) sia collegato al terminale the positive battery terminal (+), the dingt an den Pluspol (+) der Batterie
negativo cable marked (-) to be connected to angeschlossen werden, während das
(-) sulla batteria e che ci sia la messa a the negative battery terminal (-) and mit
terra. Se si usa una seconda batteria to ground the equipment. If a (-) gekennzeichnete Kabel an den
per fare partire il motore termico, colle- second battery is used to start the Minuspol (-) der Batterie anzuschließen
gare sempre morsetti di polarità uguale engine, always connect terminals of ist, der auch an Masse angeschlossen
(Fig. A). Montare una batteria con lo similar polarity (Fig. A). Any battery sein muß. Wenn man eine zweite
stesso voltaggio di quella montata sul used in this way must be of the Batterie benutzt, um den Dieselmotor in
carrello. same voltage as that fitted to the Gang zu bringen, müssen die Klemmen
Se si usa un caricatore esterno, collega- truck. When using an external bat- immer an Klemmen der gleichen
re sempre il filo (+) del caricatore al tery charger, always connect the Polarität
morsetto (+) della batteria e il filo (-) del charger positive (+) lead to the angeschlossen werden (Ab. A). Eine
caricatore al morsetto (-) della batteria e positive (+) battery terminal and the Batterie mit der gleichen Spannung wie
messo a terra. Non cortocircuitare mai charger negative lead (-) to the die Batterie des Teleskopladers verwen-
o mettere a terra i morsetti dell’alternato- negative battery terminal (-) and den. Beim Anschluß an ein externes
re. ground. Never ever short-circuit or Ladegerät ist das Pluskabel (+) des
Non invertire mai il collegamento ground the alternator terminals. Ladegerätes an den Pluspol der Batterie
dell’alternatore sulla batteria. Non Never invert the alternator connec- anzuschließen, während das Minuskabel
smontare mai o sostituire un collega- tion on the battery. Never remove or (-) des Ladegerätes an den Minuspol
mento elettrico mentre il motore è in replace an electrical connection der Batterie angeschlossen wird, der
marcia. while the engine is running. auch an Masse angeschlossen wird.
Die Klemmen der Lichtmaschine auf kei-
nen Fall kurzschließen oder an Masse
anlegen.
Den Anschluß der Lichtmaschine an der
Batterie auf keinen Fall vertauschen.
1
Downloaded from www.Manualslib.com manuals search engine
4 MRT 1432 - 1635 MSeries
IT EN DE
In caso di saldatura elettrica sul carrello, When carrying out electrical welding Elektrische Anschlüsse weder abneh-
collegare direttamente il cavo negativo operations on the truck, connect the men noch vertauschen, während der
della saldatrice sul pezzo da saldare per negative lead of the welder straight Motor läuft. Zum Ausführen von
evitare che la corrente ad alta tensione on to the part being welded to pre- Schweißarbeiten am Fahrzeug ist das
attraversi l’alternatore quindi disinserire vent high voltage current from pas- Minuskabel der Schweißmaschine direkt
la batteria. sing through the alternator, and mit der zu schweißenden Stelle zu ver-
disconnect the battery. binden, um zu vermeiden, daß die hohe
Spannung die Lichtmaschine durch-
quert. Daher die Batterie abmachen.
Scatola portafusibili e relé Fuse and relay box Sicherungen - und relaisdose
Il circuito elettrico é protetto da fusibili The electric circuit is protected by fuses Der elektrische Kreis ist durch
situati nella scatola portafusibili (FIG.A) mounted in the fuse box located Sicherungen geschützt, die sich in der
posta sotto il coperchio del cruscotto e underneath the cover of the instrument Sicherungendose unter der
nella scatola elettrica sotto la cabina panel (FIG. A) and in the electric box Armaturenbrett-Abdeckung “1” (Abb. B)
(FIG. B pag.4-7). under the cab (FIG. B page.4-7). und im Elektrogehäuse unter der Kabine
Per cambiare un fusibile, toglierlo e To change a fuse, remove it and replace (Abb. C) befinden.
sostituirlo con uno nuovo della stessa it with a new one with the same quality Um eine Sicherung auszuwechseln, sie
qualità e taratura. and calibration values. herausnehmen und mit einer neuen,
In caso di mancanza di corrente, con- If a power failure occurs, check all the gleichwertigen ersetzen.
trollare tutti i fusibili e verificare se si è fuses and verify if a short-circuit has Bei Stromausfall alle Sicherungen kon-
prodotto un cortocircuito. occurred. trollieren und sicherstellen, daß kein
NON TENTARE DI RIPARARE UN DO NOT TRY TO REPAIR A BURNED Kurzschluß vorliegt.
FUSIBILE CHE È SALTATO. FUSE. NICHT VERSUCHEN, EINE DURCH-
GEBRANNTE SICHERUNG ZU REPA-
RIEREN.
FIG.A
7,5 10
7,5 10
F33 F17 F1
7,5
E11 E4 Intermittenza
30 30
Intermittence F34 F29 30 F18 F13 30 F2
Aussetzung
7,5
10 7,5
10 7,5
F35 F19 F3
E5
10
15 5 10
15 5 10
F36 F20 F4
F30 F14
E13 E6 7,5 5
E1 F37 7,5 5
10
F21 F5
10 5
10 5
7,5
7,5
F38 F22 F6
E14 E7
7,5 10 7,5
7,5 10 7,5
F39 F23 F7
10
10 10
E15 E8 F40 10 F24 10 F8
F31 F15
15 3
15 3
F25 F9
10
E9
10 10
10 10
F26 F10
7,5
15 10
E10
F32 15 F27 F16 10 F11
7,5
5 7,5 F12
5 7,5
F28
2
Downloaded from www.Manualslib.com manuals search engine
MRT 1432 - 1635 MSeries 4
IT
Descrizione funzioni dei fusibili nella
scatola posta sotto il coperchio del
cruscotto
(FIG. A) Ref. Ampere Descrizione
F1 10 Luci di emergenza+plafoniera
F2 30 Riscaldamento [versione rotazione continua]
F3 10 Devioguida luci + avvisatore acustico da cabina
F4 10 Lampada rotante
F5 5 Devioguida inserimento marce+alimentazione sottochiave carro
F6 5 Luci di direzione
F7 7,5 Comando sterzante
F8 10 Tergicristallo anteriore e lavavetro
F9 3 Strumentazione + check controllo spie
F10 10 Fari di lavoro anteriori
F11 10 Fari di lavoro posteriori
F12 7,5 Tergicristallo posteriore e superiore
F13 7,5 Illuminazione interruttori
F14 10 Esclusione circuito idraulico [solo 1850-2150-2540] + pen-
dolo elettronico a disposizione
F15 10 Chiave di salvataggio + pressostato frenatura + elettrovalvole traslazione
F16 7,5 Microinterruttori blocco ed allineamento torre + pulsante
ripristino cambio
F17 7,5 Manipolatori Danfoss manovre da cabina
F18 30 Benna miscelatrice grande predisposizione
F19 10 Benna miscelatrice piccola predisposizione
F20 5 Positivo sotto chiave radio+antifurto
F21 7,5 Termostato riscaldatore [versione rotazione continua]
F22 10 Compressore sedile pneumatico+acceleratore elettrico
F23 10 Proximity braccio cestello abbassato + micro esclusione sollevamento
F24 10 Optional+doppia/tripla uscita+chiave esclusione sist.
antiribaltamento
F25 15 Cruscotto stabilizzatori
F26 10 Fari di lavoro sul braccio
F27 15 Elettrovalvole Danfoss
F28 5 Positivo diretto radio+antifurto
F29 Diodo 1A Marcia avanti
F30 Diodo 1A Retromarcia
F31 Diodo 3A Cicalino sistema antiribaltamento
F32 Diodo 1A Inibizione relè E15
F33 Diodo 1A Segnale retromarcia a logica
F34 Diodo 1A Segnale marcia avanti e logica
F35 Diodo 1A Segnale sist. antiribaltamento
F36 15 Ventilatore riscaldamento [solo 1542-1742 con versione
rotazione limitata]
F37 Diodo 1A Negativo relè cambio
F38 7,5 Positivo da economizzatore
F39 7,5 Positivo chiave esclusione sicurezze
F40 Diodo 3A Mantenimento pos. arr. motore
3
Downloaded from www.Manualslib.com manuals search engine
4 MRT 1432 - 1635 MSeries
EN
Functional description of the fuses in the box
located under the cover of the instrument panel
(FIG. A)
4
Downloaded from www.Manualslib.com manuals search engine
MRT 1432 - 1635 MSeries 4
DE
Funktionsbeschreibung der unter
dem armaturenbrett befindlichen
sicherungen (FIG. A)
Zeichen Ampere Beschreibung
F1 10 Warnblinkanlage + Deckenleuchte
F2 30 Heizung [beständige Rotationsfassung]
F3 7,5 Lichtschalter + Horn von Kabine
F4 10 Rundumleuchte
F5 5 Gangschalthebel + Stromversorgung unter Schlüssel Fahrgestell
F6 5 Fahrtrichtungsanzeiger
F7 7,5 Lenksteuerung
F8 10 Frontscheibenwischer + -wascher
F9 3 Instrumente + Check control Kontrollleuchte
F10 10 Arbeitsscheinwerfer vorn
F11 10 Arbeitsscheinwerfer hinten
F12 7,5 Heckscheibenwischer + Dachscheibenwischer
F13 7,5 Schalterbeleuchtung
F14 10 Abschaltung Hydraulikkreislauf [nur 1850-2150-2540] +
elektronisches Pendel, nicht belegt
F15 10 Sicherheitsschlüssel + Druckschalter Bremse + Fahrmagnetventile
F16 7,5 Mikroschalter Sperre und Ausrichtung Turm + Taste für
Rückstellung Getriebe
F17 7,5 Joystick Danfoss Manöver von Kabine
F18 30 Großer Mischgreifer Vorrüstung
F19 10 Kleiner Mischgreifer Vorrüstung
F20 5 Positiv unter Schlüssel Radio + Diebstahlsicherung
F21 7,5 Thermostat Heizung [beständige Rotationsfassung]
F22 10 Kompressor pneumatischer Sitz + elektrische Beschleunigung
F23 10 Näherungsschalter Armeskorb abgehoben + Mikroschalter
Abschaltung Hubbetrieb
F24 10 Wahlweise + doppelter dreifacher Ausgang + Schlüssel
Abschaltung Kippschutzsystem
F25 15 Armaturenbrett Stützen
F26 10 Arbeitsscheinwerfer auf Ausleger
F27 15 Magnetventile Danfoss
F28 5 Positiv direkt Radio + Diebstahlsicherung
F29 Diodo 1A Vorwärtsfahrt
F30 Diodo 1A Rückwärtsfahrt
F31 Diodo 3A Störung von Kippschutzsystem
F32 Diodo 1A Hemmung Relais E15
F33 Diodo 1A Signal Rückwärtsfahrt an Logik
F34 Diodo 1A Signal Vorwärtsfahrt an Logik
F35 Diodo 1A Signal Kippschutzsystem
F36 15 Ventilator Heizung [nur 1542-1742 mit beschränker
Rotationsfassung]
F37 Diodo 1A Negativ Relais Getriebe
F38 7,5 Positiv Arbeitskorb von Sparvorrichtung
F39 7,5 Positiv Schlüssel Abschaltung Sicherheiten
F40 Diodo 3A Beibehaltung Pos. Motorabstellung
5
Downloaded from www.Manualslib.com manuals search engine
4 MRT 1432 - 1635 MSeries
IT EN DE
SCATOLA ELETTRICA SOTTO ELECTRIC BOX UNDER THE CAB ELEKTRISCH SCHALTKASTEN
CABINA UNTER KABINE
6
Downloaded from www.Manualslib.com manuals search engine
MRT 1432 - 1635 MSeries 4
IT EN DE
Illuminazione Lighting Beleuchtung
Una lampadina bruciata deve essere A blown bulb must be changed imme- Eine durchgebrannte Glühbirne muß
immediatamente sostituita. diately. Do not handle a new bulb with sofort ersetzt werden. Eine neue
Non maneggiare una lampadina nuova bare or dirty fingers. Any traces of grea- Glühbirne nicht mit bloßen oder schmut-
a mani nude o sporche, ogni traccia di se, oil or sweat will evaporate when the zigen Händen anfassen, weil jede Spur
grasso, olio o sudore evapora quando la bulb is hot and stain the reflector. Fett, Öl oder Schweiß verdampft, wenn
lampadina si scalda e macchia così il Never touch or attempt to polish the die Glühbirne heiß wird, und der
riflettore. reflector. Just open the headlamp to Reflexspiegel dabei fleckig wird.
Non toccare mai ne tentare di lucidare il change the bulb. Versuchen Sie auf keinen Fall, den
riflettore. Aprire il faro solamente per Reflexspiegel anzufassen oder zu säu-
cambiare la lampadina. bern. Den Scheinwerfer nur öffnen, um
die Glühbirne auszutauschen.
L’efficienza della batteria è proporziona- Battery efficiency becomes progressi- Die Batterieleistung sinkt mit abnehmen-
le alla diminuzione della temperatura vely lower as the ambient temperature der Temperatur und ist bei -40°C prakti-
fino a cessare praticamente a -40°C. drops, until it practically ceases to func- sch Null.
Non cercare di usare il motorino d’avvia- tion Lassen Sie den Anlasser nicht unnütz
mento se la batteria è stata esposta a at -40°C. laufen, wenn die Batterie Temperaturen
temperature attorno a - 29°C. Never attempt to use the starter motor if um -29°C ausgesetzt worden ist.
Riscaldare in questi casi la batteria, the battery has been exposed to tempe- Die Batterie in diesen Fällen bis zu 5 cm
immergendola in acqua tiepida fino a 5 ratures of around -29°C. unter den Stopfen in lauwarmes Wasser
cm al di sotto dei tappi. In these cases, heat the battery by setzen. Bei sehr strengen
In caso di temperature molto basse, riti- immersing it in lukewarm water to 5 cm Minustemperaturen sollte die Batterie
rare la batteria dal carrello e conservarla below the cell caps. ausgebaut und in beheizten Räumen
in un ambiente caldo fino al momento di If the temperatures are very low, remove aufbewahrt werden, um dann bei der
utilizzarla. the battery from the truck and store it in Benutzung eingebaut zu werden.
a warm place until it is required.
E18
7,5
10
10
10
7,5
10
10
7,5
7,5
10
F49 F50 F51 F52 F53 F54 F55 F56 F57 F58 F59 F60
7,5
7,5
7,5
7,5
7,5
10
10
10
10
10
10
FIG.B
7
Downloaded from www.Manualslib.com manuals search engine
Downloaded from www.Manualslib.com manuals search engine
MRT 1432 - 1635 MSeries 4
SCHEMA ELETTRICO
ELECTRICAL SYSTEM
STROMFLUßPLAN
9
Downloaded from www.Manualslib.com manuals search engine
SCHEMA ELETTRICO IT ELECTRICAL SYSTEM EN STROMFLUßPLAN DE
10
4
Leggenda utilizzatori impianto elettrico MRT 1432 - 1635 Key to electrical system users Manitou MRT 1432 - 1635 Legende verbraucher der elektrischen anlage MTR 1432 - 1635
Manitou con software (riferimento n° 1966). with software (reference to drawing n° 1966). Manitou mit software (Bezugszeichning n°1966).
E25 . Relè antisonorizzazione (tav. 6-9) E27 . Powering relay for logic and anti-tipping system (tab.2- E25 . Relais Schalldämmung (Tafel 6-9)
E26 . Relè blocco sospensioni 55° (tav. 6-14) 12) E26 . Relais Sperre Radaufhängungen 55° (Tafel 6-14)
E27 . Relè alimentazione logica e sistema antiribaltamento E28 . Backup light relay (tab.14) E27 . Relais Stromversorgung Logik und Kippschutzsystem
(tav. 2-12) E29 . Vacant relay housing (Tafel 2-12)
E28 . Relè luci di retromarcia (tav. 14) E28 . Relais Rückfahrleuchten (Tafel 14)
E29 . Sede per relè a disposizione Relay installed in rear part of truck E29 . Relais: nicht belegt
E30 . Emergency pump remote control switch (tab.1-7)
Relè posizionato nella parte posteriore carro Relais im hinteren Teil des Fahrgestells
E30 . Teleruttore pompa di emergenza (tav. 1-7) Fuses and diodes in fuse box E30 . Schütz Notpumpe (Tafel 1-7)
F1 . 10A fuse : Hazard lights + roof light (tab.3)
Fusibili e diodi posizionati nella scatola fusibili F2 . 30A fuse : Heating (tab.14) [continuous model rotation] Sicherungen und Dioden in Sicherungsbox
F1 . Fusibile 10A : Luci di emergenza + plafoniera (tav. 3) F3 . 7.5A fuse : Switch for lights + horn operated from cab F1 . Sicherung 10A: Warnblinkanlage + Deckenleuchte
F2 . Fusibile 30A : Riscaldamento (tav. 14) [versione rota- (tab.3) (Tafel 3)
da cabina (tav. 3) power supply (tab.2) F3 . Sicherung 7.5A: Lichtschalter + Horn von Kabine
F4 . Fusibile 10A : Lampada rotante (tav. 5) F6 . 5A fuse : Direction indicators (tab.3) (Tafel 3)
F5 . Fusibile 5A : Devioguida inserimento marce + alimen- F7 . 7.5A fuse : Steering control (tab.4) F4 . Sicherung 10A: Rundumleuchte (Tafel 5)
tazione sottochiave carro (tav. 2) F8 . 10A fuse : Windscreen wiper + washer (tab.13) F5 . Sicherung 5A: Gangschalthebel + Stromversorgung
F6 . Fusibile 5A : Luci di direzione (tav. 3) F9 . 3A fuse : Instruments + check control indicator lights unter Schlüssel Fahrgestell (Tafel 2)
F7 . Fusibile 7. 5A : Comando sterzate (tav. 4) (tab.1) F6 . Sicherung 5A: Fahrtrichtungsanzeiger (Tafel 3)
F8 . Fusibile 10A : Tergicristallo anteriore + lavavetro (tav. F10 . 10A fuse : Front work lights (tab.13) F7 . Sicherung 7.5A: Lenksteuerung (Tafel 4)
13) F11 . 10A fuse : Rear work lights (tab.13) F8 . Sicherung 10A: Frontscheibenwischer + -wascher
F9 . Fusibile 3A : Strumentazione + check controllo spie (tav. F12 . 7.5A fuse : Rear window wiper + top windscreen wiper (Tafel 13)
1) (tab.13) F9 . Sicherung 3A: Instrumente + Check control
F10 . Fusibile 10A : Fari di lavoro anteriori (tav. 13) F13 . 7.5A fuse : Switch lighting (tab.8) Kontrollleuchte n (Tafel 1)
F11 . Fusibile 10A : Fari di lavoro posteriori (tav. 13) F14 . 10A fuse : Vacant electronic pendulum + hydraulic cir- F10 . Sicherung 10A: Arbeitsscheinwerfer vorn (Tafel 13)
F12 . Fusibile 7. 5A : Tergicristallo posteriore + tergicristallo cuit cut-out [only 1850-2145] (tab.6) F11 . Sicherung 10A: Arbeitsscheinwerfer hinten (Tafel 13)
superiore (tav. 13) F15 . 10A fuse : Safety key + braking pressure switch + F12 . Sicherung 7.5A: Heckscheibenwischer +
F13 . Fusibile 7. 5A : Illuminazione interruttori (tav. 8) transfer travel solenoid valves (tab.7) Dachscheibenwischer (Tafel 13)
F14 . Fusibile 10A : Esclusione circuito idraulico [solo 1850- F16 . 7.5A fuse : Gearbox reset button + mast alignment F13 . Sicherung 7.5A: Schalterbeleuchtung (Tafel 8)
2145] + pendolo elettronico a disposizione (tav. 6) and locking micro switch (tab.2) F14 . Sicherung 10A: Abschaltung Hydraulikkreislauf, nicht
F15 . Fusibile 10A : Chiave di salvataggio + pressostato fre- F17 . 7.5A fuse : Danfoss controls for manoeuvres from cab belegt + elektronisches Pendel, nicht belegt (Tafel 6)
natura + elettrovalvole di traslazione. (tav. 7) (tab.8) F15 . Sicherung 10A: Sicherheitsschlüssel + Druckschalter
F16 . Fusibile 7. 5A : Microint. blocco ed allineamento torre F18 . 30A fuse : Pre-engineering for large mixer bucket Bremse + Fahrmagnetventile (Tafel 7)
+ pulsante ripristino cambio (tav. 2) (tab.3) F16 . Sicherung 7.5A: Mikroschalter Sperre und Ausrichtung
F17 . Fusibile 7. 5A : Manipolatori Danfoss manovre da F19 . 10A fuse : Pre-engineering for small mixer bucket Turm + Taste für Rückstellung Getriebe (Tafel 2)
cabina (tav. 8) (tab.3) F17 . Sicherung 7.5A: Joystick Danfoss Manöver von
F18 . Fusibile 30A : Benna miscelatrice grande predisposi- F20 . 5A fuse : Radio + anti-theft device key-activated positi- Kabine (Tafel 8)
zione (tav. 3) ve contact (tab.3) F18 . Sicherung 30A: Großer Mischgreifer Vorrüstung (Tafel
F19 . Fusibile 10A : Benna miscelatrice piccola predisposi- F21 . 7.5A fuse : Heater thermostat (tab.14) [continuous 3)
zione (tav. 3) model rotation] F19 . Sicherung 10A: Kleiner Mischgreifer Vorrüstung (Tafel
F20 . Fusibile 5A : Positivo sotto chiave radio + antifurto (tav. 3)
3) F22 . 10A fuse : Air cushioned seat compressor + electric F20 . Sicherung 5A: Positiv unter Schlüssel Radio +
F21 . Fusibile 7. 5A : Termostato riscaldatore (tav. 14) [ver- accelerator (tab.13) Diebstahlsicherung (Tafel 3)
sione rotazione continua] F23 . 5A fuse : Basket lowered boom proximity + lifting disa- F21 . Sicherung 7.5A: Thermostat Heizung (Tafel 14)
F22 . Fusibile 10A : Compressore sedile pneumatico + bling micro (tab.11) [beständige Rotationsfassung]
acceleratore elettrico (tav. 13) F24 . 10A fuse : Optional + double/triple output + anti-tipping F22 . Sicherung 10A: Kompressor pneu matischer Sitz +
F23 . Fusibile 5A : Proximity braccio cestello abbassato + system disabling key (tab.8) elektrische Beschleunigung (Tafel 13)
11
4
micro esclusione sollevamento (tav. 11) F25 . 15A fuse : Outrigger control panel (tab.8) F23 . Sicherung 5A: Näherungsschalter Armeskorb abgeho-
F24 . Fusibile 10A : Optional + doppia/tripla uscita + chiave F26 . 10A fuse : Work lights on boom (tab.13) ben + Mikroschalter Abschaltung Hubbetrieb (Tafel 11)
12
esclusione sist. antiribaltamento (tav. 8) F27 . 15A fuse : Danfoss solenoid valves (tab.7) F24 . Sicherung 10A: Wahlweise + dop pelter dreifacher
4
F25 . Fusibile 15A : Cruscotto stabilizzatori (tav. 8) F28 . 5A fuse : Anti-theft device + radio direct positive con- Ausgang + Schlüssel Abschaltung Kippschutzsystem
F26 . Fusibile 10A : Fari lavoro su braccio (tav. 13) tact (tab.3) (Tafel 8)
F27 . Fusibile 15A : Elettrovalvole Danfoss (tav. 7) F29 . 1A diode : Forward travel (tab.2) F25 . Sicherung 15A: Armaturenbrett Stützen (Tafel 8)
F28 . Fusibile 5A : Positivo diretto radio + antifurto (tav. 3) F30 . 1A diode : Reverse travel (tab.2) F26 . Sicherung 10A: Arbeitsscheinwerfer auf Ausleger
F29 . Diodo 1A : Marcia avanti (tav. 2) F31 . 3A diode : Anti-tipping system buzzer (tab.12) (Tafel 13)
F30 . Diodo 1A : Retromarcia (tav. 2) F32 . 1A diode : Relay E15 inhibition (tab.12) F27 . Sicherung 15A: Magnetventile Danfoss (Tafel 7)
F31 . Diodo 3A : Cicalino sistema antiribaltamento (tav. 12) F33 . 1A diode : Reversing signal to logic (tab.4) F28 . Sicherung 5A: Positiv direkt Radio +
F32 . Diodo 1A : Inibizione relè E15 (tav. 12) F34 . 1A diode : Forward travel signal to logic (tab.4) Diebstahlsicherung (Tafel 3)
F33 . Diodo 1A : Segnale retromarcia a logica (tav. 4) F35 . 1A diode : Anti-tipping system signal (tab.12) F29 . Diode 1A: Vorwärtsfahrt (Tafel 2)
F34 . Diodo 1A : Segnale marcia avanti a logica (tav. 4) F36 . 15A fuse : Heating fan (tab.14) [only 1542-1742 limi- F30 . Diode 1A: Rückwärtsfahrt (Tafel 2)
F35 . Diodo 1A : Segnale sist. antiribaltamento (tav. 12) ted model rotation] F31 . Diode 3A: Störung von Kippschutzsystem (Tafel 12)
F36 . Fusibile 15A : Ventilatore riscaldamento (tav. 14) [solo F37 . 1A diode : Gearbox relay negative contact (tab.12) F32 . Diode 1A: Hemmung Relais E15 (Tafel 12)
1542-1742 con versione rotazione limitata] F38 . 7.5A fuse : Basket positive contact from economiser F33 . Diode 1A: Signal Rückwärtsfahrt an Logik (Tafel 4)
F37 . Diodo 1A : Negativo relè cambio (tav. 12) (tab.7) F34 . Diode 1A: Signal Vorwärtsfahrt an Logik (Tafel 4)
F58 . Fusibile 7. 5A : Luci di retromarcia (tav. 14) F61 . 3A diode : Levelling solenoid valve 2 (tab.10) [only F56 . Sicherung 10A: Positiv unter Schlüssel hintere Teil
F59 . Fusibile 10A : Alimentazione logica + sistema antiribal- 1850-2145] Fahrgestell (Tafel 2)
tamento (tav. 12) F62 . 3A diode : Levelling solenoid valve 1 (tab.10) [only F57 . Sicherung 7.5A: Schalldämmung (Tafel 6)
F60 . Diodo 3A : Inibizione ritorno masse (tav. 7) 1850-2145] F58 . Sicherung 7.5A: Rückfahrleuchten (Tafel 14)
F61 . Diodo 3A: Elettrovalvola livellamento 2 (tav. 10) [solo F63 . 3A diode : Outrigger main solenoid valve (tab.8) F59 . Sicherung 10A: Stromversorgung Logik +
1850-2145] F64 . Vacant fuse or diode housing Kippschutzsystem (Tafel 12)
F62 . Diodo 3A: Elettrovalvola livellamento 1 (tav. 10) [solo F60 . Diode 3A: Hemmung Massenrückschlag (Tafel 7)
1850-2145] Fuse in engine compartment F61 . Diode 3A: unbelegt (Tafel 10)
F63 . Diodo 3A: Elettrovalvola generale stabilizzatori (tav. 8) F65 . 100A fuse : Main power supply (tab.1) F62 . Diode 3A: unbelegt (Tafel 10)
F64 . Sede per fusibile o diodo a disposizione F63 . Diode 3A: Allgemeines Magnetventil Stützen (Tafel 8)
G1 . Alternator (tab.1) F64 . Sicherung oder Diode: unbelegt
Fusibile posizionato nel vano motore H1 . Hour counter (tab.1)
F65 . Fusibile 100A : Alimentazione generale (tav. 1) I1 . Micro switch with two contacts for parking brake Sicherung im Motorraum
G1 . Alternatore (tav. 1) (tab.4) F65 . Sicherung 100A: Allgemeine Stromversorgung (Tafel
13
4
I33 . Microinterruttore anomalia catena 2 (tav. 4) [solo I35 . Electrical accelerator switch (tab.13) I31 . Taste Stütze hinten rechts (Tafel 9)
1742-1850-2145] I36 . Boom extension PNP proximity (tab.10) I34 . Näherungsschalter Kabine blockiert 2 (Tafel 6)
14
I34 . Proximity cabina bloccata 2 (tav. 6) I37 . 3 m boom ascent PNP proximity (tab.10) I35 . Elektrischer Gasschalter (Tafel 13)
4
I35 . Interruttore acceleratore elettrico (tav. 13) I38 . Vacant electronic levelling pendulum (tab.10) I36 . Näherungsschalter PNP Ausleger ausfahren (Tafel 10)
I36 . Proximity PNP sfilo braccio (tav. 10) I39 . Pendulum basket lowered boom PNP proximity I37 . Näherungsschalter PNP Ausleger 3 m heben (Tafel
I37 . Proximity PNP salita braccio 3 mt (tav. 10) (tab.11) 10)
I38 . Pendolo elettronico di livellamento a disposizione (tav. I40 . Chain fault micro switch 3 (tab.4) [only 1742-1850- I38 . Elektronisches Nivellierpedel, nicht belegt (Tafel 10)
10) 2145] I39 . Näherungsschalter PNP Pendelkorb mit Armeskorben
I39 . Proximity PNP braccio cestello a pendolo abbassato I41 . Lifting inhibiting micro switch (tab.11) abgehoben (Tafel 11)
(tav. 11) I50 . Swivel limited proximity 2 (tab.10) [only 1542-1742] I41 . Mikroschalter Überlastabschaltung Hubbetrieb (Tafel
I40 . Microinterruttore anomalia catena 3 (tav. 4) [solo I51 . Anti-tipping disabling key (tab.12) 11)
1742-1850-2145] I52 . Max. engine coolant temp. thermal contact (tab.5) I50 . Näherungsschalter Rotation beschränkt 2 (Tafel 10)
I41 . Microinterruttore esclusione sollevamento (tav. 11) I53 . Hazard light switch (tab.3) [nur 1542-1742]
I50 . Proximity rotazione limitata 2 (tav. 10) [solo 1542- I54 . Rotating beacon switch (tab.5) I51 . Schlüssel Überlastabschaltung Kippschutz (Tafel 12)
1742] I55 . Braking pressure switch (tab.12) I52 . Temperaturgeber max. Wert Kühlwasser (Tafel 5)
I51 . Chiave esclusione sistema antiribaltamento (tav. 12) I56 . Windscreen wiper and washer switch (tab.13) I53 . Schalter Warnblinkanlage (Tafel 3)
I52 . Termocontatto max. temp. acqua motore (tav. 5) I57 . Rear window and top windscreen wiper switch (tab.13) I54 . Schalter Rundumleuchte (Tafel 5)
L9 . Indicatore ottico pendolo attivo a disposizione (tav. 10) L15 . Dipped headlamps indicator light (tab.3) L16 . Kontrollleuchte Blinker (Tafel 4)
L12 . Indicatore ottico marcia veloce inserita (tav. 12) L16 . Direction indicators indicator light (tab.4) L17 . Kontrollleuchte Handbremse (Tafel 4)
L13 . Indicatore ottico marcia lenta inserita (tav. 12) L17 . Parking brake indicator light (tab.4) L18 . Kontrollleuchte unbelegt (Tafel 5)
L14 . Indicatore ottico carica batteria (tav. 1) L18 . Vacant indicator light (tab.5) L20 . Kontrollleuchte Luftfilter verstopft (Tafel 5)
L15 . Indicatore ottico luci abbaglianti (tav. 3) L19 . Outriggers partially extended indicator light (tab.5) L21 . Kontrollleuchte niedriger Druck Motoröl (Tafel 5)
L16 . Indicatore ottico luci di direzione (tav. 4) L20 . Air filter fouled indicator light (tab.5) L22 . Kontrollleuchte max. Temperatur Kühlwasser (Tafel 5)
L17 . Indicatore ottico freno di stazionamento (tav. 4) L21 . Low engine oil pressure indicator light (tab.5) L23 . Kontrollleuchte unbelegt (Tafel 5)
L18 . Indicatore ottico a disposizione (tav. 5) L22 . Max. engine coolant temperature indicator light (tab.5) L24 . Kontrollleuchte unbelegt (Tafel 4)
L19 . Indicatore ottico stabilzzatori parzialmente usciti (tav. L23 . Vacant indicator light (tab.5) L25 . Kontrollleuchte Allradlenkung (Tafel 4)
5) L24 . Chain fault indicator light (tab.4) [only 1742-1850- L26 . Kontrollleuchte normale Lenkart (Tafel 4)
L20 . Indicatore ottico filtro aria intasato (tav. 5) 2145] L27 . Kontrollleuchte Hundegang (Tafel 4)
L21 . Indicatore ottico bassa pressione olio motore (tav. 5) L25 . Concentric steering indicator light (tab.4) L30 . Kontrollleuchte Ausfahren (Tafel 8)
L22 . Indicatore ottico max temperetura acqua motore (tav. L26 . Normal steering indicator light (tab.4) L31 . Kontrollleuchte Einfahren (Tafel 8)
5) L27 . Crab steering indicator light (tab.4) M1 . Anlasser (Tafel 1)
1850-2145] L30 . Extension indicator light (tab.8) M4 . Joystick Danfoss Kabine rechter Teil (Tafel 8)
L25 . Indicatore ottico sterzata concentrica (tav. 4) L31 . Return indicator light (tab.8) M6 . Joystick Fahrstufe langsam-schnell (Tafel 12)
L26 . Indicatore ottico sterzata normale (tav. 4) M1 . Starter motor (tab.1) M7 . Pumpe Scheibenwaschanlage (Tafel 13)
L27 . Indicatore ottico sterzata granchio (tav. 4) M2 . Emergency electric pump (tab.1) M8 . Frontscheibenwischer (Tafel 13)
L28 . Indicatore ottico selezione travi (tav. 8) M3 . Danfoss control lh part of cab (tab.8) M9 . Heckscheibenwischer (Tafel 13)
L29 . Indicatore ottico selezione stabilizzatori (tav. 8) M4 . Danfoss control rh part of cab (tab.8) M10 . Dachscheibenwischer (Tafel 13)
L30 . Indicatore ottico sfilo (tav. 8) M6 . High-low speed control (tab.12) M11 . Kraftstoffpumpe Heizung (Tafel 14) [beständige
L31 . Indicatore ottico rientro (tav. 8) M7 . Screen washer pump (tab.13) Rotationsfassung]
M1 . Motorino avviamento (tav. 1) M8 . Windscreen wiper motor (tab.13) M12 . Sitzkompressor (Tafel 13)
M2 . Elettropompa di emergenza (tav. 1) M9 . Rear window wiper motor (tab.13) M13 . Elektrischer Gashebel (Tafel 13)
M3 . Manipolatore Danfoss cabina parte sinistra (tav. 8) M10 . Top windscreen wiper motor (tab.13) M14 . Heizlüfter (Tafel 14) [beschränker Rotationsfassung]
M4 . Manipolatore Danfoss cabina parte destra (tav. 8) M11 . Heating fuel pump (tab.14) [continuous model rotation] P1 . Bremslicht links (Tafel 2)
M6 . Manipolatore marcia lenta-veloce (tav. 12) M12 . Seat compressor (tab.13) P2 . Bremslicht rechts (Tafel 2)
M7 . Pompa lavacristallo (tav. 13) M13 . Electrical accelerator (tab.13) P3 . Blinker vorn links (Tafel 3)
M8 . Tergicristallo anteriore (tav. 13) M14 . Heating fan (tab.14) [only 1542-1742 limited model
M9 . Tergicristallo posteriore (tav. 13) rotation] P4 . Blinker hinten links (Tafel 3)
M10 . Tergicristallo superiore (tav. 13) P1 . Lh rear brake light (tab.2) P5 . Blinker vorn rechts (Tafel 3)
M11 . Pompa combustibile riscaldamento (tav. 14) [versione P2 . RH rear brake light (tab.2) P6 . Blinker hinten rechts (Tafel 3)
rotazione continua] P3 . Lh front direction indicator light (tab.3) P7 . Standlicht vorn links (Tafel 3)
M12 . Compressore sedile (tav. 13) P4 . Lh rear direction indicator light (tab.3) P8 . Standlicht hinten rechts (Tafel 3)
M13 . Acceleratore elettrico (tav. 13) P5 . Rh front direction indicator light (tab.3) P9 . Standlicht vorn rechts (Tafel 3)
M14 . Ventilatore riscaldamento (tav. 14) [solo 1542-1742 P6 . Rh rear direction indicator light (tab.3) P10 . Standlicht hinten links (Tafel 3)
con rotazione limitata] P7 . Lh front side light (tab.3) P11 . Abblendlicht links (Tafel 4)
P1 . Luce di arresto posteriore sinistro (tav. 2) P8 . Rh rear side light (tab.3) P12 . Abblendlicht rechts (Tafel 4)
P2 . Luce di arresto posteriore destro (tav. 2) P9 . Rh front side light (tab.3) P13 . Fernlicht links (Tafel 4)
P3 . Luce di direzione anteriore sinistra (tav. 3) P10 . Lh rear side light (tab.3) P14 . Fernlicht rechts (Tafel 4)
P4 . Luce di direzione posteriore sinistra (tav. 3) P11 . Lh dipped headlamp (tab.4) P15 . Kabinenbeleuchtung (Tafel 3)
P5 . Luce di direzione anteriore destra (tav. 3) P12 . Rh dipped headlamp (tab.4) P16 . Rundumleuchte (Tafel 5)
P6 . Luce di direzione posteriore destra (tav. 3) P13 . Lh driving beam (tab.4) P17 . Arbeitsscheinwerfer vorn (Tafel 13)
P7 . Luce di posizione anteriore sinistra (tav. 3) P14 . Rh driving beam (tab.4) P18 . Arbeitsscheinwerfer hinten (Tafel 13)
P8 . Luce di posizione posteriore destra (tav. 3) P15 . Cab roof light (tab.3) P19 . Rückfahrleuchte links (Tafel 14)
P9 . Luce di posizione anteriore destra (tav. 3) P16 . Rotating beacon (tab.5) P20 . Rückfahrleuchte rechts (Tafel 14)
P10 . Luce di posizione posteriore sinistra (tav. 3) P17 . Front work light (tab.13) P21 . Arbeitsscheinwerfer auf Ausleger (Tafel 13)
P11 . Proiettore anabbagliante anteriore sinistro (tav. 4) P18 . Rear work light (tab.13) P22 . Warnleuchte Überlastabschaltung Kippschutzsystem
15
4
P12 . Proiettore anabbagliante anteriore destro (tav. 4) P19 . Lh backup light (tab.14) (Tafel 3)
P13 . Proiettore abbagliante anteriore sinistro (tav. 4) P20 . Rh backup light (tab.14) P23 . Alarm Überlastabschaltung Kippschutzsystem (Tafel
16
P14 . Proiettore abbagliante anteriore destro (tav. 4) P21 . Work lights on boom (tab.13) 12)
4
P15 . Plafoniera cabina (tav. 3) P22 . Anti-tipping system disabling alarm light (tab. 3) R1 . Widerstand 68ž 2W (Tafel 1)
P16 . Lampada rotante (tav. 5) P23 . Anti-tipping system disabling alarm (tab.12) R2 . Heizung (Tafel 14) [beständige Rotationsfassung]
P17 . Faro di lavoro anteriore (tav. 13) R1 . 68ž 2W resistor (tab.1) R3 . Thermostat Heizung (Tafel 14) [beständige
P18 . Faro di lavoro posteriore (tav. 13) R2 . Heating (tab.14) [continuous model rotation] Rotationsfassung]
P19 . Luce di retromarcia posteriore sinistra (tav. 14) R3 . Heating thermostat (tab.14) [continuous model rota- S1 . Magnetventil Danfoss Heben (Tafel 7)
P20 . Luce di retromarcia posteriore destra (tav. 14) tion] S2 . Magnetventil Danfoss Teleskop (Tafel 7)
P21 . Fari lavoro su braccio (tav. 13) S1 . Danfoss lifting solenoid valve (tab.7) S4 . Magnetventil Danfoss Rotation (Tafel 7)
P22 . Lampada allarme esclusione sistema antiribaltamento S2 . Danfoss extension solenoid valve (tab.7) S5 . Magnetventil Danfoss Schwenken (Tafel 7)
(tav. 3) S4 . Danfoss swivelling solenoid valve (tab.7) S7 . Magnetventil Danfoss wahlweise (Tafel 7)
P23 . Allarme esclusione sistema antiribaltamento (tav. 12) S5 . Danfoss tilting solenoid valve (tab.7) S8 . Magnetventil Handbremse (Tafel 2)
R1 . Resistore 68ž 2W (tav. 1) S7 . Optional Danfoss solenoid valve (tab.7) S9 . Magnetventil allgemein Stützen (Tafel 5)
R2 . Riscaldamento (tav. 14) [versione rotazione continua] S8 . Parking brake solenoid valve (tab.2) S10 . Magnetventil Überlastabschaltung Arbeitshydraulik,
R3 . Termostato riscaldamento (tav. 14) [versione rotazione S9 . Main outriggers solenoid valve (tab.5) nicht belegt (Tafel 6)
continua] S10 . Hydraulic circuit cut-out solenoid valve (tab.6) [only S11 . Magnetventil Stützen vorn rechts aufgebockt (Tafel 8)
S33 . Elettrovalvola doppia uscita testa braccio (tav. 8) ST1 . Anti-tipping system (tab.12)
S34 . Elettrovalvola tripla uscita testa braccio (tav. 8) ST2 . Fuel level gauge (tab.5)
S35 . Elettrovalvola livellamento 1 (tav. 10) [solo 1850-2145] ST4 . Energy economiser (tab.1-7-11) FARBENERKLƒRUNG
S36 . Elettrovalvola livellamento 2 (tav. 10) [solo 1850-2145] T1 . Fuel level transmitter (tab.5) A : Hellblau H : Grau R : Rot
EE . Economizzatore di energia (tav. 1-11) TR . Thermostarter (tab.1) B : Weiß L : Blau S : Rosa
ST1 . Sistema antiribaltamento (tav. 12) C : Orange M : Braun V : Grün
ST2 . Strumento livello combustibile (tav. 5) G : Gelb N : Schwarz Z : Violett
ST4 . Economizzatore di energia (tav. 1-7-11) KEY TO COLOURS
T1 . Trasmettitore livello combustibile (tav. 5) A: Bright blue H: Grey R: Red
TR . Termoavviatore (tav. 1) B: White L: Blue S: Pink Beispiele :
C: Orange M: Brown V: Green AB 1.5 = hellblauweiß Querschn. 1.5 mm2
LEGENDA COLORI G: Yellow N: Black Z: Purple AB = hellblauweiß Querschnitt. 1 mm2
A: Azzurro H: Grigio R: Rosso
B: Bianco L: Blu S: Rosa Examples:
Esempi:
AB 1,5 = Azzurrobianco sez. 1,5 mm2
AB= Azzurrobianco sez. 1 mm2
17
4
Schema elettrico/Electrical system/Stromflußplan
18
4
INSTRUMENTBRET
Hinter/Verkabelung Turm
SICHERUNGSDOSE
Instrumentbret
StŸtzfŸsse
- Anlage Erhitzen
KISTCHEN UNTERWAGEN
MRT 1432 - 1635 MSeries
Legenda simboli/Symbols legend/Erlauterungen symbol
MX-XX
= Presa radio comando - Radio control intake - Steckdose funk steuerung
MX-XX
= Presa predisposizione impianto rimorchio Predisposition trailer system intake
Steckdose voreinstellung anlage anhanger
PTX = Ponte removibile - Removable bridge - Beweglice brucke
19
4
Tavola 1 / Table 1 / Tafel 1
20
4
M1.5
F65 3
C18-A-B-C-D
M2.5
2
100A
RN°
4
R2.5
M4
C18-W
2
F9
EE GZ 10
C13-1 C5-19 10
JP3-12 C15-W C16-W
3A SL SL SL BV
E30 12
RN nr9
R4
C3-A-B
7/18 C22-K 3
CHECK
GZ
C3-10
24
GZ
C18-18
C14-2
RN RN RN RN GZ
C6-13
06 12
M2 M L14 R1
GZ M2.5
GZ
CHECK
CHECK
HR nr.1 HRnr.1
2xM4 Bnr.3
CHIAVE
KEY
C2-5
Bnr.3
SCHLUSSEL
C2-3
M4 M4
GZ
R50
33 P 0 1 2 3 58 15/54 19 50 17
30 M1
031
033
CHECK
E19
30
B1 1/16
R6 LN2.5
R10
C21-H
4xM2.5
C20-3
044
C2-A-B-C-D
L4
C21-K
HR
50
M LN2.5
G1 G
C18-13
LB
C20-2
CHECK
CHECK
CHECK
CHECK
CHECK
GZ
L4 B
28 21 22 23 27 TR
E18 E19
BV N N N
034
C21-C C1-V BV BV
019
C4-4
C2-6
E18
M2.5 BV
HR 1/10
1/6 E13 1/18
C20-1
M4 M4
4/7 C2-E-F-G-H
L10
h H1 041 3
C18-E-F-G-H
L10
2
DISPONIBILE - AVAILABLE - ZUR BESTIMMUNG M1.5*
7
N
043 2
C18-I-J-K-L C2-I-J-K-L
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
MRT 1432 - 1635 MSeries
Tavola 2 / Table 2 / Tafel 2
M2.5 M2.5
1 4
RN*
6
M4 M4
1 3
R2.5 RNnr.16
6
GM
14
F16 R2.5
C3-4
MRT 1432 - 1635 MSeries
RN
C3-16
RN CB E22 RNnr.2
C3-18
5
4
1 0
I4 R2.5 2/16
R2.5
5
CB R1.5 R1.5
CB GV
4
1
C2-4
F29 F30 VH + CL
GV N 4
F55 F56
032
GV 015
10A 10A
C1-R
RN
C23-L
C17-C
10
GV
C19-S
C20-aa
RV
GV 6
RV
C20-V
RV RN
RV
I3
C21-J
ZN ZR ZB
I5 I6 I7 I8
C23-N
C23-M
RN
C17-D
C20-R
C18-1
VH CL N N
R
C4-11
C19-T
ZR ZV ZV
040 PR-3
C2-12 E24 E22 E27
C17-U
VH E10 R
E9 H N N MV MV
S8 4/9
4/5
N
HG
016
N1.5
C4-6
023
HG GM
X8-5
X6-5
C1-U
6/7 2/9 12/10
C4-10
C1-HH
R R
018
C1-S
C19-1
C1-CC
028
P1 P2
C21-M
MV MV ZN ZB
MV
GM
C18-5
C18-3
C18-2
C20-C
C20-A
HG GM L1 L2
N
S21 S22 A2
N N
N N N
N N
1 3
L10 L10
1 3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
21
4
Tavola 3 / Table 3 / Tafel 3
22
4
M1.5 M1.5
1 7
R4 R4
1 14
M4 M4
2 4
R2.5 R2.5 M4 R2.5
C3-K
C3-15
C3-2
RL R
C3-1
C4-1
C3-13
C7-D RN
C4-36
C10-B
C10-2
2 3 1 2 3 1 CB CB SG BR
RNnr.3 SG RNnr.3
2 8 5 10
P15 1 0
1 2 4 6 3 1 7
0 3
GR LN L
11
11
L
C16-M
GR
57/58 56b 56a 54/S 54/D 49 Z 4
B HN VN LN L Z SG
4
C15-M
C6-23 C13-11 Z C22-L
Z Z
VN
10
C1-AA
021
C1-FF
C1-GG
C21-E
026
027
08
CHECK
CHECK
02
PR-1
PR-5
F50 F49
7.5A 7.5A HN
G GN 10
L
LN
G GN LN
VNnr.1
C19-G
C20-F
C17-T
C18-11
C19-H
C20-G
C17-S
C18-9
L PR-2 LN PR-6
Z
X1-4
X2-2
X8-2
X2-4
X6-4
X8-4
X1-2
X6-2
P5
P9 P10 P7 P8 L4 A1 L15 P6 P3 P4
MV MV MV MV BR N N MV MV MV MV
C19-K
C20-C
C19-J
C20-B
N N
2 4
C20-D-E
L10 L10
2 MV
10
L10 L10
1 4
MRT 1432 - 1635 MSeries
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
Tavola 4 / Table 4 / Tafel 4
GV
2
VH+CL
2
M4 M4
3 5
M2.5 M2.5
2 12
R2.5
RN RN
1 5
RNNR.2 RN
2
JP6-1
16
SG MS M2.5 R2.5
MRT 1432 - 1635 MSeries
16
3 E5 RN1.5nr7
C14-27
E 20 E5 E 21 VBnr1
C3-12
MZ RN1.5nr7
C16-S
C4-25
C4-23
C5-9
C4-26
RV
C4-27
RV
I 24 4 8 3 7 10
VN1.5 2 1 0
4/13
SG GR
C15-S
C4-32
INT 01
L MS MS
31 R 2 6 1 5 9
C
VB
HN1.5 HS
CHECK
F 33 F 34
SMnr1 RN
C4-24
BR I 40 L 25
C4-30
C4-31
L17 L 26
C1-DD
C1-EE
L 27
PT1
1 0 2 I2 L 24 LV
025
024
09
CHECK
I 32
C18-7
A5 25
SM
N VB VH
CHECK
C4-22
M LV
C20-GG C18-6
C20-HH
I 33
C19-V
C19-W
M AB SM
C23-P
RNNR.13
C4-12
C4-5
7
C4-13
M AB SM N
F 51 F 52 I1 5 6 10
CHECK
10 A 10 A
1 0
03 E9 E 13 E 10
Lnr.1
1 7 2 8 9
HN VN
C16-GG
LV
C19-C
C19-D
C19-E
C19-F
P13
L16 P11 P12 P14 S24 S25
N N
N N N N N
LI0 LI0
3 12
N N
3 5
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
23
4
Tavola 5 / Table 5 / Tafel 5
24
4
RNnr.13
8
M4 M4
4 6
R2.5 R2.5
2 6
RN°
4 SN
12
I62
C20-cc
RN R1.5
R2.5
SB RN
I63
F4 F53
10A ST2 L 10A
C20-dd
S N
C3-14
C19-U
I64 RN1.5
SB
RN
E23
I65
CHECK
CHECK
CHECK
CHECK
CHECK
8/12
29 L18 32 L20 30 L21 31 L22 35 L23
GH HV H BN GL BR1.5
SN
C19-2
C17-B
C1-M
C1-BB
C2-7
C2-10
BR1.5
RNnr.4 RNnr13
012
022
035
038
1 10 S9
013
1 0
I54
N1.5
C1-N
SN
C18-4
C18-14
C18-15
5 9
C17-A
SN
AB N S H BN
HV
L19
t
C7-C
T1 I12 I13 I52
AB
N N
P16
N
N N
4 6
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
MRT 1432 - 1635 MSeries
Tavola 6 / Table 6 / Tafel 6
M4 M4
5 7
R2.5 R2.5
5 14
RN*
2
RV
2 R2.5
RNnr.16 RNnr.16
2 10
RN RN
RV
RN
F54 F57 F14
MH I16 7.5A 7.5A 10A
E7 CV1.5
B RN
C6-33
C6-1
C3-17
14/19
MH RN
C4-7
JP3-5
C23-F
RV
I17
1
HS
MN MN
C13-12
JP3-2
JP1-20
E24 I22
2
C20-M
JP1-24
L6 B RV
L5
C6-22
JP1-9
2/13 Bnr.9
C14-16
C14-7
C19-N
C23-G
GM N B C14-29
MH HS LV HB
C2-9
I18 BHnr1
C6-4
RV
RV
037
JP1-4
E26
JP2-4
B
C13-13
C11-T
C14-5
C11-S
14/11
RV
V
C21-L
BHnr1
LV
I19 V I23
C6-9
LV
C11-U-V
HB C14-28
BHnr1
C17-F
C6-21
C4-21
C5-7
RN BHnr1
002
I71 GM E11 E11 E1
C1-B
LV E25
6/16
C4-9 HB BL
C1-T
CB C20-A
CB
N
C20-N
LV C20-P
017
C19-B
6/17 7/2
t
t
N
S23 S26 S10
N N
N N N
N N
5 7
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
25
4
Tavola 7 / Table 7 / Tafel 7
26
4
M4 M4
6 8
R2.5
R2.5
RNnr.15
10
RNnr.13 RNnr.13
4 8
M1.5
C3-5
C23-A
3
C4-37
RN1.5
12
F27 F38 F39 F15
1 10
15A 7.5A 7.5A 10A 1 0
I9
MG1.5 MV1.5
GV
C4-38
C4-39
JP3-1
JP3-11
JP3-7
JP3-9
JP3-10
SH N
JP3-6
C23-E
L V B S ZN
C5-18
GL
E1
JP3-4
C13-16
C13-2
H2.5 6/18
C8-19
SB
G
1
C13-15
C6-18
3 4
C3-J
MV1.5
I10 10
3
0
4 BR
JP6-4
C6-19
C8-1
C5-5
ZN GL
C14-33
BL
C6-32
C13-7
C6-28
C13-3
C6-34
C13-9
C6-31
C13-6
C6-29
C13-4
F40
MH
MB M
C2-11
C15-EE
M 17
S5 S1 S7 S4 S2 L3 17
C2-8
C18-18
N N N N N N
BR
036
E30
N
M1.5*
1
C18-17
C18-16
M AR
S30 1/3
NB
C20-EE
F60
NB M
10
C20-FF
N N N
6 8
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
MRT 1432 - 1635 MSeries
Tavola 8 / Table 8 / Tafel 8
RNnr.13
7
RNnr.13 RNnr.13
5 13
M4 M4
7 11
C2.5
12
R2.5 R2.5 R2.5
GN2.5 RN SN2.5
12
4 10 I66
2 1 0
GN1.5
C8-A
GN2.5
C3-6
MRT 1432 - 1635 MSeries
CLnr.4 RNnr.13
RNnr17 9
C3-F
HR2.5
JP3-3
JP5-4
C8-C C3-G
GN2.5 C11-BB C8-5
GN1.5
JP1-15
JP1-11
C4-2
BN2.5 R2.5 I26 12
Hnr.44 CLnr.4
3 4
1 0 2
C8-G
C5-C
C13-18
C13-17
VB AB
Hnr.44
JP1-2
JP1-10
JP1-23
C11-1
C6-16
C6-17
1 7 2 8
GN2.5
BL
C8-15
RN
C8-14
C8-H
CV SG BG I25 BL
4 10 Hnr.44
2 1 0
C13-D
CLnr.4
C13-C
2 6 9
C6-15 R BR
SN2.5 C2.5 N I28
5 6 10
C13-19 1 0
C11-3
C11-2
C14-19
C14-20
I27
C1-P
5 6 10
Hnr.4
JP1-21
1 0
C14-23
C14-24
C10-D
C10-C
CL
1 7 2 8 9
014
JP5-1
C14-1
LR C N
1 7 2 8 9
C11-F
C11-E
C11-C
C11-B
B
PRED.DOPPIA/TRIPPLA USCITA
C21-B
C8-12
C8-13
C6-14
BR R RL RB R
SG BG VB AB 9
1 10 BR
8 7 5 M3 1 0 8 7 5 M4 9
I72 HL
10
14 16 14 16 F63
1 2 15 3 10 22 1 2 15 3 10 22
C1-K
C1-L
C1-D
5 9 L28
CV RN RN BR CV RN RN BR HL
B N
011
010
004
C14-18
C11-G
C11-M
C11-N
C11-K
C11-H
C11-R
C11-P
C11-L
C14-17 E23
L29 N
C17-L
C17-J
C17-R
CL LR C
C11-J
C11-D
S15 S17 S11
S34 S33 HL
5/17
C14-22
N N N
HL
JP1-19
C10-G
C10-F
N N
7 9
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
27
4
Tavola 9 / Table 9 / Tafel 9
28
4
RN
6
R
8
BR
8
RNnr.13 RNnr.13
8 10
E25
1 7 2 8 9 1 7 2 8 9 1 7 2 8 9 GM
6/10
GR CV
C15-V
GM
CR GL N AG N
C16-V
C8-6
C8-7
HL CN N
C8-8
C8-9
C8-10
C8-11
15
C1-H
C1-F
C1-C
C1-G
C1-J
C1-E
15
009
006
003
007
005
008
GM
C17-K
C17-P
C17-H
C17-N
C17-G
C17-M
C19-A
HL CN CR GL GR AG CV
S16 S12 S18 S13 S19 S14 S20 S29
N N N N N N N N
N N
8 10
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
MRT 1432 - 1635 MSeries
Tavola 10 / Table 10 / Tafel 10
RNnr.13
9
RNnr.16 RNnr.16
6 14
RV
6
RNnr.15 RNnr.15
7 12
RN
2
MV1.5
7 RN
C22-T
JP1-16
JP1-12
ZB ZB ZB
I70 1 0 MB
MRT 1432 - 1635 MSeries
C14-31
RN
JP5-5
JP4-12
1 7 2 8 9 RN
PT2
PT3
R
SL N MG LB
CB I11 I50
C6-36
C6-37
RN2.5
C23-K
C14-36
M M CB RN RN RN
7 RN2.5
C6-20 C13-14 C14-15 C6-2 C23-J
C5-8
CB
C6-44
C15-1
C22-J RN2.5 PROXIMITY ER
C14-32
JP4-3
JP1-5
JP1-1
JP3-8
C23-B
ROTATZIONE LIMITATA
C16-1
NZ
M2.5 LIMITED ROTATION
3 4 10
C13-10
1 0 2
JP1-8
1 C GL VERSION PROXIMITY
I69
BESCHRANKTE
C14-11
C14-12
GR
DREHUNG PROXIMITY
1 7 2 8 9 RN RN
C23-D MR MH MB
C23-C 001 GR
C1 C1-A C21-A C2 I36 I37
C2-2
C6-27
C2-1
RV BR
N N
030
029
C6-25
C6-26
C6-10
MR
C21-F MH
PREDISP. PENDOLO LIVELLAMENTO
C21-G
SV SR
C19-L
MR I38
C19-M
N + S -
MR F62 F61
S35 MH
S36 E20 E21
VN
3
BR GR
HN 4/11 4/13 L9
3
HL
8 N
N N
9 11
L10 L10
3 14
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
29
4
Tavola 11 / Table 11 / Tafel 11
30
4
M4 M4
8 13
R2.5
C3-E
RN
1
JP2-6
JP2-9
JP2-2
JP2-5
JP2-11
JP2-1
JP2-7
JP4-6
JP4-8
JP4-7
JP4-2
JP4-11
JP4-4
JP4-5
JP4-1
JP4-9
C5-E
C6-38
JP2-12
RN1.5
R
RB RG ML NG CG MV ZV ZG CL HS SN HG VN GN LN BN CR
C13-A
R
CL HS SN HG VN GN LN BN CR
JP6-3
R
24 C22-B C22-C C22-E C22-F C22-H C22-M C22-N C22-S
C16-A
C16-AA
C16-L
C16-D
C16-F
C16-J
C16-E
C16-G
C16-B
C15-T
GV
12
20
3
18
2
5
6
8
13
C15-P
3
18
2
5
6
8
13
C16-T
12
20
RN
1
C16-P
23
4
PREDISPOSITION HAUT - PARIEUR
4
LOUDSPEAKER PREDISPOSITION RN
LAUTSPRECHER VOREINSTELLUNG GV
I39 I41
19
14
+ RH
19
14
C14-13
C16-BB
+
C16-R
RB
HAUT-PARIEUR DROIT C7-L B BV
RIGHT LOUDSPEAKER
7
- NB
RECHTS LAUTSPRECHER
C7-M
C15-BB
C15-R
N2.5 V
C7-R
MR MR B BV
C7-S
C16-4
JP1-22
C7-T
JP2-3
JP6-5
JP2-10
JP6-6
C15-4
C7-U
N N
10 12
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
MRT 1432 - 1635 MSeries
Tavola 12 / Table 12 / Tafel 12
GNI.5
8
M2.5
4
ZB
11
RNI.5
7
RNNR.15 RNNR.15
10 14
1 BV
BV* I55 RN E6
11 RN PT4
MR 30
C8-3
ZB ZB R
JP4-10 F37
SN GZ
5
MRT 1432 - 1635 MSeries
3
4
3 M6 Z 86
C2.5 I51 1 0 2
8 E 27 87 87a
3
4
C7-P
C4-28
JP5-2
RV RV
SN2.5 C4-17
8 GZ G2.5
ZB HN 1 7
E14
CH
BV 30
P23 F 59
C14-10
C14-8
BV 10A 85
Z S
C15-3
C15-2
C23-R
SN2.5 C2.5
C4-29
G2.5
C4-19
C6-5
S
C6-7
C4-20 86
C16-3
C16-2
C21-I
C9-C
87 87a
C6-35
GV2.5 L2.5
C5-16
A4
21
22
042
E15
C1-1
C9-K
ZB 30
C9-E
G2.5 SN CH ZB F32 85
C4-18
C9-G
1 4 5 7 ST1
C8-4
C14-26
BH
C5-D
3 86
2 6 GV 87 87a
PROLUNGA CESTELLO
HR N2.5 H
JP1-7
C4-34
HN
21
22
G2.5 F35
C6-12
C14-4 C6-11
C4-33
C14-3
C5-3
C5-4
JP5-3
JP5-6
HR HN
CB1.5 C1.5 BR2.5 RV BH
JP1-13
C13-H
S31 S32 S28 L13 L12 S27
JP1-17
N N C5-G N N N N
LIO
LIO
4 14
N
N
11 13
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
31
4
Tavola 13 / Table 13 / Tafel 13
32
4
M4 M4
11 14
RNnr.13 RNnr.13
8 14
R2.5 R2.5 R2.5 R2.5 R2.5 R2.5
M12
F22 F8 F12 F10 F11 F26
10A 10A 7.5A 10A 10A 10A
2 1 RN1.5nr12
RN1.5nr:10 RN1.5nr:11
C3-7
R1.5 RN1.5nr.8
C5-6
RN1.5nr12
C3-9
C3-8
C3-3 RN2.5
C3-11
NB 5 10 4 8 3 7 10
I67
2 1 0 1 13/15
2 0
C22-P
5 9
B2.5
C14-34
N
4 2 7 9 2 6 1 5 9
RB MR
RN1.5nr12 HV HL
BG
C22-R
AG N N
NB
C4-15
C3-H
C14-35
RN1.5nr.8
C7-H
C7-G
C7-E
C7-F
M13
C7-N
M E8
C5-17
RB RN1.5nr.10 RN1.5nr.11
13/18
C5-1
C5-2
NB RB RN 1 10 1 10
1 0 I58 1 0
3 4 10 I59
1 0 2
C10-A
I35 RN1.5nr12
5 9 5 9
1 7 2 8 9
BG
R1.5 N N R1.5 N N
RN1.5nr.8 BV HV CB1.5
HL
C7-B
C7-A
M7 M M8 M M9 M M10 M P21
GV1.5 ZB1.5
N N N N P17 P18
N1.5 N1.5
C10-E
N N
12 14
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
MRT 1432 - 1635 MSeries
Tavola 14 / Table 14 / Tafel 14
R2.5
6
RNnr.16
10
GM
2
RNnr.15
12
M4
13
R4
3
R1.5
MRT 1432 - 1635 MSeries
C4-35
RN4
F36 F21 F58
2 6 1 5 9
15A 7,5A 7,5A
RN4 LR MR N
ML1.5
RB
E4 30
85
C3-D
RN4
C3-19
RN
C8-16
C6-39
MG 86
C8-F
C21-M
C3-1
G G RB M C6-40
RN4
C8-D
I60 I15
8 9 12 R2 R3 C1-W
TERMOSTATO
C12-3
RISCALDAMENTO - HEATING N N
020
THERMOSTAT
C4-8
10 11 7 5
V1.5 N1.5 MG B4
C12-E
C21-D
C8-7 GM CH
C12-D
C12-C
Z
C23-S
C23-T
C12-1
N N N
PR-4
C6-24
C6-41
C8-K
CA CZ CZ
V1.5
C20-H
C20-J
MV
6/7 14/15 6/4
X6-3
X8-3
M11 M
N1.5 P19 P20
MV MV
L10
12
N
13
L10
10
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
33
4
Tavola 15 / Table 15 / Tafel 15
34
4
V6
1
RV
V 2.5 V 2.5
HV 15
1 E33 F68 F67
A1
20 A 20 A
18 16
VB VN 2.5
V 2.5
30 30
E31 E32
86 86
85 85
87 87a 87 87a
V 2.5
VN 2.5
M16 M17
M M
N
14
MRT 1432 - 1635 MSeries
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
Tavola 16 / Table 16 / Tafel 16
C8-16
NON UTILIZZATO
NOT USED
C12-G
NICHT VERWENDET C12-F
RB
LB MB V1.5 M G
G C12-K
4 13 3 14 R2 3 5 6 R3
TERMOSTATO
RISCALDAMENTO - HEATER THERMOSTAT
7 11 8 9 5 2 1
HR MB
HR B2.5 R2.5
C12-D
C12-H
C12-1
C12-J
C12-2
C23-S
B4 HR
RN4
C6-24
TERMOSTATO AMBIENTE
C8-K
C8-F
( 14.1 ) ENVIRONMENT THERMOSTAT
( 14.5 )
V1.5 CA
M11 M
N1.5 M2.5
N1.5
C6-41
M2.5
C12-4
C12-C
C23-T
N1.5
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
35
4
Tavola 17 / Table 17 / Tafel 17
36
4
STROMFLUßPLAN
SCHEMA ELETTRICO 3B6 - ELECTRICAL SYSTEM 3B6 - STROMFLU PLAN 3B6
UMMST01-4/XX U2MIC
DIODO 1N4007
DI_0
DI_1
DI_2
DI_3
DI_4
Dl_5
DO_0
DO_1
WDO
+VB
-VB
+V_OUT
Dl_6
DO_2
DO_3
Al_3
Al_7
+15v
GND
Al_0
Al_1
Al_4
Al_5
+5V
GND
Al_2
Al_6
+VOUT
RX
TX
GND
C2 C7
C3 C1
6x0,35 L=12.5 m
4x0,5 L= 3.5 m
12x0.5 L= 3.5 m
Grey
Pink
Yellow
Protective covering L = 9 m
Brown
White
Green
Brown
Yellow
Green
White
6x0.35 L= 4.5 m
C2 C7
4 Outtrigger
5 Front Side
6 Short Outtrigger
7 Basket
3 Cut-off
11
C1
1
10
Protective covering L = 4 m
Brown
White
Green
Yellow
Grey
Pink
GV
1 4 3 2 KB1
1 2 3 4 5 6 SH
TX
RX
+V
A1
A2
S1
S2
+V
GND
GND
SHLD
+UB
CIT -UB
4x0,5 L=1.6 m
4x0,5 L=1.6m
4x0,5 L=1.1 m
4x0,5 L=1.1 m
6 3 3 6 L M
Brown
White
Green
Brown
White
Green
Brown
White
Green
Brown
White
Green
Connections cable side. Connections Display side. D K J
Female Plug Male plug
C3 C4 C5 C6
1 3 2 1 3 2 1 3 2 1 3 2
C
A CABLE N°7
C1 C2 C3 C7 CABLE N°4 B
+UB
GND
OUT
SCH
+UB
GND
OUT
SCH
+UB
GND
OUT
SCH
+UB
GND
OUT
SCH
CABLE N°6 CABLE YEL/GRE
P P P P
S C H E M A I D R AU L I C O
H Y D R AU L I C S C H E M E
S C H E M A H Y D R AU L I K
37
Downloaded from www.Manualslib.com manuals search engine
Schema impianto idraulico dei movimenti
38
4
Moviment hydraulic system
Hydrauliknanlage der bewegungsablaufe
IT
SCHEMA IMPIANTO IDRAULICO DEI MOVIMENTI MOVIMENT HYDRAULIC SYSTEM HYDRAULIKNANLAGE DER BEWEGUNGSABLAUFE
D = Distributore Danfoss D.F = Danfoss flow divider for steering system D = Wegeventil Danfoss
R = Serbatoio olio D = Danfoss valve system R = Ölbehälter
F.A. = Filtro aspirazione R = Oil tank F.A. = Saugfilter
F.R. = Filtro scarico F.A. = Intake filter F.R. = Ablassfilter
C.S.P. = Valvola sicurezza pilotata V.C = Compensating cylinder C.S.P. = Vorgesteuertes Sicherheitsventil
C.S.P.D. = Valvola sicurezza pilotata doppia C.S.P. = Piloted safety valve C.S.P.D. = Vorgesteuertes doppeltes Sicherheitsventil
E.S. = Elettrovalvola selettrice per gli stabilizzatori C.S.P.D. = Double piloted safety valve E.S. = Magnetventil für Stützenwahl
M.V. = Motore ventola E.S. = Selector solenoid valve for outriggers M.V. = Lüftermotor
I = Idroguida M.V. = Fan motor I = Hydrolenkung
S.T. = Stabilizzatori I = Power steering system S.T. = Stützen
F.M. = Filtro mandata S.T. = Outriggers F.M. = Filter in Druckleitung
F.M. = Delivery filter
EN
DE
39
4
Schema impianto idraulico stabilizzatori
40
4
Outrigger hydraulic system
Hydrauliknanlage - abstutzungen
IT
SCHEMA IMPIANTO IDRAULICO STABILIZZATORI OUTRIGGER HYDRAULIC SYSTEM OUTRIGGER HYDRAULIC SYSTEM
41
4
Impianto idraulico freno/acceleratore/blocco ponte posteriore/comando cambio/sterzo
42
4
Brake/accelerator/front axle locking/gearbox control/steering hydraulic system
Hydraulikanlage bremse/beschleuniger/achsensperre vorne/getriebesteuerung/lenkung
IT
F.D.A.V. = Freni a dischi anteriore F.D.A.V. = Front axle disk brakes V.B.P.A. = Sperrzylinder Hinterachse
M = Motore termico M = Internal combustion engine F.D.A.V. = Vordere Scheibenbremsen
P.H. = Pompa idrostatica P.H. = Hydrostatic pump M = Verbrennungsmotor
V.C.L.R. = Cilindro comando lenta-veloce V.C.L.R. = Fast-slow control cylinder P.H. = Hydrostatische Pumpe
V.S.L.R. = Valvola selettrice lenta-veloce P. = Double gear pump R.C.F.P. = Steuerhahn Handbremse
R.C.F.P. = Rubinetto comando freno di stazionamento F.A. = Intake filter P. = Doppelt Zahnradpumpe
P. = Pompa doppia ingranaggi F.R. = Drain filter F.A. = Saugfilter
F.A. = Filtro aspirazione D.F. = Flow divider F.R. = Ablassfilter
F.R. = Filtro scarico E = Solenoid valve D.F. = Flussmengenteiler
D.F. = Divisore di flusso V.D. = Steering cylinders E = Magnetventil
E = Elettrovalvola I.D. = Steering pump V.D. = Lenkzylinder
V.D. = Cilindri sterzo S = Oil tank I.D. = Lenkpumpe
EN
43
4
4 MRT 1432 - 1635 MSeries (400°)
IT EN DE
Transmission hydraulic system
Impianto elettrico trasmissione
Hydraulikanlage - antrieb
44
Downloaded from www.Manualslib.com manuals search engine
IT EN DE
45
4
4 MRT 1432 - 1635 MSeries
IT EN DE
- Questo libretto di manutenzione viene - This maintenance handbook is - Dieses Wartungshandbuch wird vom
consegnato con la macchina dal supplied with the machine by the MANITOU-Händler zusammen mit der
concessionario MANITOU. MANITOU dealer. Maschine übergeben.
- Accompagnerà la macchina durante il - It will be kept with the machine during - Es begleitet die Maschine während der
periodo di garanzia contrattuale e in the contractual warranty period and ganzen vertraglich festgelegten
seguito permetterà di seguire una afterwards will be used to follow the Garantiezeit und anschließend erlaubt
regolare manutenzione raccomandata regular maintenance recommended by es, eine regelmäßige Wartung anhand
da MANITOU. MANITOU. der Empfehlungen von MANITOU
- La manutenzione dei materiali assicura - Performing maintenance on materials durchzuführen.
l’affidabilità e la perfetta efficienza del ensures the reliability and perfect - Die Wartung der Materialien
mezzo. operating efficiency of the equipment. gewährleistet die Zuverlässigkeit und
- Il concessionario MANITOU propone - The MANITOU dealer proposes die perfekte Funktionstüchtigkeit des
formule di manutenzione adattate ai maintenance programmes that are Laders.
diversi bisogni garantendo, per la sua adapted to meet various needs - Der MANITOU-Händler empfiehlt je
competenza e l’utilizzo di pezzi di guaranteeing, thanks to his competence nach den verschiedenen
ricambio originali MANITOU, la and the use of MANITOU original Anforderungen ausgearbeitete
massima efficienza. spare parts, the maximum efficiency. Wartungsformeln und
- Consigliamo di conservare il LIBRETTO - It is recommended to keep the garantiert aufgrund seiner
DI MANUTENZIONE durante tutto il MAINTENANCE HANDBOOK as long Zuständigkeit und der Verwendung von
periodo di esistenza della macchina e in as the machine is owned and in MANITOU - Originalersatzteilen
particolare di consegnarlo al futuro particular to hand it over to the future maximale Zuverlässigkeit.
proprietario in caso di eventuale owner if the machine is sold. - Der Hersteller empfiehlt des weiteren
rivendita della macchina. die Aufbewahrung des WARTUNG
SHAND-BUCHES während der ganzen
Lebensdauer des Fahrzeuges und es
bei einem evtl. Verkauf des Laders,
dem neuen Besitzer zu übergeben.
OSSERVAZIONI:
NOTES:
BEMERKUNGEN:
OSSERVAZIONI:
NOTES:
BEMERKUNGEN:
OSSERVAZIONI:
NOTES:
BEMERKUNGEN:
46
Downloaded from www.Manualslib.com manuals search engine
MRT 1432 - 1635 MSeries 4
IT EN DE
OSSERVAZIONI:
NOTES:
BEMERKUNGEN:
OSSERVAZIONI:
NOTES:
BEMERKUNGEN:
OSSERVAZIONI:
NOTES:
BEMERKUNGEN:
OSSERVAZIONI:
NOTES:
BEMERKUNGEN:
OSSERVAZIONI:
NOTES:
BEMERKUNGEN:
OSSERVAZIONI:
NOTES:
BEMERKUNGEN:
47
Downloaded from www.Manualslib.com manuals search engine
4 MRT 1432 - 1635 MSeries
IT EN DE
OSSERVAZIONI:
NOTES:
BEMERKUNGEN:
OSSERVAZIONI:
NOTES:
BEMERKUNGEN:
OSSERVAZIONI:
NOTES:
BEMERKUNGEN:
OSSERVAZIONI:
NOTES:
BEMERKUNGEN:
OSSERVAZIONI:
NOTES:
BEMERKUNGEN:
OSSERVAZIONI:
NOTES:
BEMERKUNGEN:
48
Downloaded from www.Manualslib.com manuals search engine
MRT 1432 - 1635 MSeries 4
IT EN DE
OSSERVAZIONI:
NOTES:
BEMERKUNGEN:
OSSERVAZIONI:
NOTES:
BEMERKUNGEN:
OSSERVAZIONI:
NOTES:
BEMERKUNGEN:
OSSERVAZIONI:
NOTES:
BEMERKUNGEN:
OSSERVAZIONI:
NOTES:
BEMERKUNGEN:
OSSERVAZIONI:
NOTES:
BEMERKUNGEN:
49
Downloaded from www.Manualslib.com manuals search engine
4 MRT 1432 - 1635 MSeries
IT EN DE
OSSERVAZIONI:
NOTES:
BEMERKUNGEN:
OSSERVAZIONI:
NOTES:
BEMERKUNGEN:
OSSERVAZIONI:
NOTES:
BEMERKUNGEN:
OSSERVAZIONI:
NOTES:
BEMERKUNGEN:
OSSERVAZIONI:
NOTES:
BEMERKUNGEN:
OSSERVAZIONI:
NOTES:
BEMERKUNGEN:
50
Downloaded from www.Manualslib.com manuals search engine
MRT 1432 - 1635 MSeries 4
IT EN DE
51
Downloaded from www.Manualslib.com manuals search engine
4 MRT 1432 - 1635 MSeries
IT EN DE
52
Downloaded from www.Manualslib.com manuals search engine
Downloaded from www.Manualslib.com manuals search engine
Downloaded from www.Manualslib.com manuals search engine
5 - AC C E S S O R I P R E V I S T I I N O P Z I O N E E
D I A G R A M M I D I P O R TATA
A N B AU G E ÄT E AU F A N F R A G E U N D
L E I S T U N G S - TA B E L L E N
- Il costruttore mette a vostra disposizione - The manufacturer makes available - Der Hersteller stellt Ihnen eine
(con garanzia) una vasta gamma di (with warranty) a vast range of reichhaltige Auswahl von
accessori per il vostro carrello elevatore accessories perfectly suited to your Anbaugeräten (mit Garantie) für Ihren
e ad esso perfettamente adattati. lift-truck. Gabelstapler zur Verfügung, die sich
diesem perfekt anpassen.
- Gli accessori sono consegnati con un
diagramma di carico relativo al vostro - The accessories are supplied complete - Das Anbaugerät wird mit einem
carrello elevatore. Il libretto d’istruzioni with a load charts relating to your Lastdiagramm geliefert, das für Ihren
e il diagramma di carico dovranno truck. The user manual and the load Gabelstapler maßgebend ist. Die
rimanere nel carrello elevatore. L’uso diagram must be kept on the truck. Bedienungsanleitung und das
dei possibili accessori é regolato dalle The use of the possible accessories is Lastdiagramm müssen sich stets beim
istruzioni contenute nel presente subject to the instructions in this Gabelstapler befinden. Für die
manuale. manual. Verwendung des möglichen
Anbaugeräts sind die Anweisungen im
vorliegenden Handbuch maßgebend.
Alcune utilizzazioni specifiche richiedono Some specific uses require adaptation Bei einigen spezifischen Anwendungen
l’addattamento dell’accessorio non of the accessory, not included in the ist eine Anpassung des Anbaugeräts
previsto negli optional in listino. optionals in the catalogue. erforderlich, die nicht in der Liste des
wahlweisen Zubehörs berücksichtigt ist.
Esistono altre soluzioni; per maggiori Other solutions are possible; contact Es gibt noch weitere
informazioni rivolgetevi al vostro agente your agent or dealer for further Lösungsmöglichkeiten. Bitte, wenden
o concessionario. information. Sie sich zwecks weitere Informationen
an den für Sie zuständigen Vertreter
oder Vertragshändler.
Solo gli accesori omologati e certificati Only accessories approved by the Auf unseren Gabelstaplern dürfen nur
“CE” dal costruttore sono utilizzabili sui manufacturer can be used on our Anbaugeräte verwendet werden, die
nostri carrelli elevatori. La responsabilità lift-trucks. The manufacturer will have no vom Hersteller zugelassen wurden.
del costruttore non sarà coinvolta in liability in case of modifications or use of Die Produkthaftung des Herstellers fin-
caso di modifica o utilizzazione di acces- accessories without his knowledge. det im Falle einer Veränderung oder
sori effettuata a sua insaputa. Verwendung von Zubehör ohne adessen
Wissen keine Anwendung.
Come dimostrano i diagrammi, tutti gli All the attachments with must be used in Alle zubehore mit ausleger mussen in
accessori con braccio devono essere horizontal position as it’s shown in load horizontaler stellung benuzt wereden
utilizzati in posizione orizzontale; per gli charts; verify that winches have a per- wie es in den lastdiagramme.
argani verificare la perfetta verticalità fect vertical position with the fitted pen- Nachprufen dass die winde eine perfek-
tramite il pendolo posto sul telaio dulum on the chassis of the attachment. te vertikale stellung haben mit der
dell’ accessorio. benuztung des pendels, zum chassis
des zubehors gestellt.
MANITOU si è assicurata sulla capacità MANITOU assures oneself about the MANITOU HAT SICH VERISHERT ÜBER DEM
d’impiego di questo carrello in condizioni employement’s capacity of this machine LEISTUNGSBEREICH DES GABELSTAPLERS IN
normali d’utilizzo previsti nel manuale in normal conditions of working foreseen NORMAL ARBEITSBEDINGUNGEN IN DEM
d’istruzioni, con un coefficiente di prova in the user’s manual, with a static test ANWEISUNG MANUELL, VORGESEHEN, MIT
statico di 1.33 e un coefficiente di prova coefficient of 1.33 and a dynamic test EINEM STATISCHEN PROBENCOEFFIZIENT VON
dinamico di 1, previsti nelle norme coefficient of 1, foreseen in the 1, IN DEN VORSCHRIFTEN EN 1459, FÜR DIE
armonizzate EN 1459 per i carrelli a harmonized rules EN 1459 for the MASCHINEN MIT WECHSELDEN LEISTUNG UND
portata variabile e EN 1726-1 per i truck with variable capacity and EN 1726-1 FUR DIE MASCHINEN MIT RAMPE.
carrelli a rampa. EN 1726-1 for the forklift
Attenzione! Siate prudenti! E’ in gioco Caution! Take care! Your safety or Achtung! Seien sie vorsichtig! Ihre
la vostra sicurezza o quella del carrel- that of the truck is at stake sicherheit und dies des gebelstaplers
lo steht auf dem spiel.
elevatore.
- Follow the data provided in the load - Halten Sie sich an die Daten auf den
- Attenersi ai dati indicati sui diagrammi diagram. Never attempt to raise loads Lastdiagrammen. Versuchen Sie
di carico. In nessun caso tentare di greater than those permitted in the keinesfalls, Lasten zu heben, die über
sollevare carichi superiori a quelli load charts supplied with the machine. den zulässigen Lasten liegen, die auf
ammessi sui diagrammi di carico alle- - Transport the load in low position with den der Maschine beiliegenden
gati alla macchina. the telescopic boom fully retracted. Lastdiagrammen angegeben sind.
- Trasportare il carico in posizione bassa - Drive the truck at a speed suitable to - Transportieren Sie die Last in niedriger
e con il braccio telescopico rientrato al the conditions and the state of the Stellung und mit ganz eingefahrenem
massimo. ground. Teleskoparm.
- Guidare il carrello ad una velocità
- When the truck is empty, travel with - Fahren Sie mit dem Gabelstapler unter
adeguata alle condizioni e allo stato
the telescopic boom lowered and fully Einhaltung einer den Bedingungen und
del terreno.
retracted. dem Zustand des Bodens angemesse-
- A carrello vuoto viaggiare con braccio
- Never go too fast or brake sharply with nen Geschwindigkeit.
telescopico abbassato e rientrato al
massimo. a load. - Beim Fahren mit leerem Gabelstapler
- Non andare mai troppo forte né frenare - When the load is lifted, check that muß der Teleskoparm gesenkt und
bruscamente con un carico. no-one can get in the way of the ganz eingefahren sein.
- Quando il carico viene sollevato, fare operation and take care not to carry - Fahren Sie keinesfalls zu schnell noch
attenzione che nessuno possa intral- out incorrect procedures. bremsen Sie mit einer Last abrupt ab
ciare l’operazione e non compiere - Never attempt operations which - Beim Anheben der Last achten Sie
manovre errate. exceed the lift-truck’s capacity. darauf, daß niemand diesen Vorgang
- Non tentare di compiere operazioni - Take care over electrical cables. stören kann, und führen Sie keine
che superino le capacità del carrello - Never leave the truck parked with a falschen Manöver aus.
elevatore. raised load. - Versuchen Sie keinesfalls,
- Fare attenzione ai cavi elettrici. - Never authorise anyone to approach or Bewegungen auszuführen, die die
- Non lasciare in nessun caso il carrello pass under the load. Leistungsfähigkeit des Gabelstaplers
in parcheggio con un carico sollevato. - Always think of safety and only tran- übersteigen.
- Non autorizzare nessuno ad avvicinar- sport well balanced loads. - Achten Sie auf die elektrischen Kabel.
si o a passare sotto il carico. - Never leave the truck loaded with the - Lassen Sie den Gabelstapler keinesfal-
- Pensare sempre alla sicurezza e parking brake engaged on gradients ls mit angehobener Last geparkt
trasportare solamente dei carichi ben exceeding 15%. stehen.
equilibrati. - With the winch or equipment with a - Erlauben Sie niemandem, sich der
- Non lasciare il carrello carico con il load hanging from the hook, always Last zu nähern oder unter dieser
freno di stazionamento inserito su una adopt the following precautions: durchzugehen.
pendenza superiore al 15%. - Position the winch perpendicular to the - Denken Sie stets an die Sicherheit und
- Con argano o attrezzature con carico
load to be lifted. transportieren Sie nur gut ausbalan-
appeso al gancio é necessario:
- The empty hook must be lowered cierte Lasten.
- Posizionare l’argano
slowly (gently) since if it is operated - Lassen Sie den beladenen
perpendicolarmente al carico da
too quickly the cable wound round the Gabelstapler nicht mit angezogener
sollevare.
- La discesa del gancio a vuoto, deve drum may become slack, causing Feststellbremse auf einem Untergrund
essere avviata lentamente serious problems for the cable, the limit mit mehr als 15% Neigung.
(dolcemente) poiché se azionata stop device, etc. - Mit Winde oder Ausrüstung und
velocemente può allentare la fune hängender Last ist folgende
attorcigliata sul tamburo, con gravi Vorgehensweise erforderlich:
guai per la fune stessa, il fine corsa, - Positionieren Sie die Winde lotrecht
ecc... zur anzuhebenden Last.
- Das Senken des leeren Hakens hat
langsam (vorsichtig) zu erfolgen, da
durch schnelles Senken des Hakens
der Seilpacken auf der Trommel ver-
dreht wird, was zu schweren
Störungen am Seil selbst, am
Endanschlag usw. führen kann.
- Se la fune , sul bozzello tende ad - If the cable tends to become twisted - Falls das Seil dazu neigt, sich um den
avvitarsi, sganciare il gancio capocor around the block, release the fixed end Seilblock zu winden, klinken Sie den
da fisso, tirare la fune e ruotarla nel hook, pull the cable in the opposite Ösenschuh mit dem feststehenden
senso opposto fino ad annullare direction until the twisting is eliminated, Haken aus, ziehen Sie am Seil und
l’avvitamento, quindi riagganciare il then re-connect the end unit. drehen Sie es in entgegengesetzter
capocorda. - Operate the control lever gently to Richtung, bis kein Umwinden mehr
- Manovrare con dolcezza la leva di prevent jerking of the load and vorhanden ist.
comando per evitare sobbalzi del possible problems in the winding of the Anschließend klinken Sie den
carico ed eventuali difettosi cable onto the drum. Ösenschuh wieder ein.
avvolgimenti della fune sul tamburo. - Raise the load vertically, avoiding - Betätigen Sie den Bedienhebel
- Sollevare il carico verticalmente, swaying and slanting lifting.
vorsichtig, um ein Springen der Last
evitando oscillazioni e sollevamenti und eventuell falsches Aufwickeln des
- Check the cable daily; if it is worn or
obliqui. Seils auf der Trommel zu vermeiden.
damaged or has even one broken
- Verificare giornalmente lo stato della - Heben Sie die Last senkrecht an und
strand (see ISO 4309) replace it
fune, se usurata, rovinata o anche vermeiden Sie Hin- und Herschwingen
immediately (contact your dealer).
solamente con un filo rotto (vedi ISO sowie schräges Heben.
4309), provvedere immediatamente - Check that the hydraulic hook raising - Überprüfen Sie täglich den Zustand
alla sostituzione (consultare il vostro and lowering limit stop is in good des Seils.
consessionario). working order and that the brake holds Falls das Seil verschlissen oder
- Verificare giornalmente l’efficenza del with load applied. beschädigt ist oder auch nur eine
fine corsa idraulico salita e discesa - Oil the revolving part of the hook gerissene Litze aufweist (siehe ISO
gancio e la tenuta del freno con carico in periodically. 4309), muß das Seil umgehend
applicato. - Check periodically that the cable is ausgewechselt werden (wenden Sie
- Lubrificare periodicamente con olio la winding onto the drum correctly. sich dazu an Ihren Vertragshändler).
parte rotante del gancio. - The following accessories are not - Überprüfen Sie täglich, ob der
- Verificare periodicamente il buon intended for systems for lifting or hydraulische Endanschlag zum Heben
avvolgimento della fune sul tamburo. moving people. und Senken des Hakens und die
- Gli accessori seguenti non sono - Before putting the winch or any other Bremse bei eingehängter Last
destinati ad impianti per il equipment in which the load hangs einwandfrei funktionieren.
sollevamento o lo spostamento di from a hook into service, report it to - Schmieren Sie den Drehbereich des
persone. the relative authority (ISPEL) in your Hakens in regelmäßigen Abständen
- Prima della prima messa in servizio zone for checking (for Italy only). mit Öl.
dell’argano, o di qualsiasi altra - Every year, remember to request your - Überprüfen Sie in regelmäßigen
attrezzatura che appenda il carico con local health authority (USL) for a visit Abständen, ob sich das Seil auf der
un gancio, denunciarlo alla autorità of inspection (Italy only). Trommel richtig aufwickelt.
preposta per il controllo (ISPEL) della - Die folgenden Anbaugeräte sind nicht
vostra zona (solo per Italia). für Anlagen zum Heben oder
- Ricordarsi ogni anno seguente di Befördern von Personen geeignet.
richiedere la visita di controllo alla USL - Vor Inbetriebnahme der Winde oder
della vostra zona (solo per Italia). eines jeden anderen Anbaugeräts, bei
dem die Last mit einem Haken auf-
gehängt wird, muß das Gerät bei der
für Ihr Gebiet zuständigen
Kontrollbehörde (ISPEL) gemeldet
werden (nur für Italien).
- Denken Sie daran, in jedem Folgejahr
bei der für Ihr Gebiet zuständigen USL
die Inspektion zu beantragen (nur für
Italien).
Prima della messa in servizio dell’arga- Before putting the winch into operation Vor der Inbetriebnahme der Winde am
no sul carrello elevatore accertarsi della on the lift-truck check that the machine Gabelstapler vergewissern Sie sich, daß
compatibilità della macchina e della is compatible and that its safety system das Gerät und die Einstellung seines
taratura del suo sistema di sicurezza al is set appropriately for the type of winch Sicherheitssystems mit dem gewünsch-
tipo di argano desiderato. required. ten Windentyp kompatibel sind.
Una taratura non conforme del sistema Incorrect setting of the safety system Eine Einstellung, die nicht dem
di sicurezza può risultare molto pericolo- may put your safety at serious risk; if in Sicherheitssystem entspricht, kann für
sa per la vostra sicurezza, se avete Ihre persönliche Sicherheit gefährlich
dubbi non esitate, consultate immediata- doubt, do not hesitate to contact your sein. Falls Sie Zweifel haben, wenden
mente il vostro concessionario. dealer immediately. Sie sich unverzüglich an Ihren
Vertragshändler.
Alcuni accessori, tenuto conto delle loro In view of their size, when the boom is Einige Anbaugeräte können aufgrund
dimensioni, e con il braccio abbassato e lowered and retracted some accessories ihrer Abmessungen und bei gesenktem,
may interfere with the front tyres and
rientrato, rischiano di interferire con i damage them if the board is tilted eingefahrenem Arm mit den
pneumatici anteriori e di provocare il loro downward. Vorderrädern in Berührung kommen und
deterioramento se l’inclinazione zu deren Verschleiß beitragen, wenn
dell’attrezzatura é rivolta in basso. das Anbaugerät nach unten gerichtet ist.
Per eliminare tale rischio, far uscire il To eliminate this risk, extend the Zur vermeidung dieser gefahr lassen
braccio telescopico di una lunghezza telescopic system far enough to eli- sie den teleskoparm je nach gabelsta-
sufficiente in funzione del carrello minate the interference (the distance pler und anbaugerat ausreIchend weit
will depend on the truck and the
elevatore e dell’accessorio, in modo ausfahren, so dass keine storung
accessory).
tale che non avvengano interferenze. mehr auftreten kann.
I carichi massimi sono definiti dalla The maximum loads are defined by the Die Höchstlasten werden durch die
capacità del carrello elevatore, tenuto lift-truck’s capacity, bearing in mind the Leistungsfähigkeit des Gabelstaplers
weight and centre of gravity of the unter Berücksichtigung des Gewichts
conto del peso e del centro di gravità und des Schwerpunkts des Anbaugeräts
accessory. If the capacity of the acces-
dell’accessorio. Qualora l’accessorio sory is below that of the lift-truck, never bestimmt. Sollte das Anbaugerät eine
avesse una capacità inferiore a quella exceed this limit. geringere Leistungsfähigkeit als die des
del carrello elevatore, non superare mai Gabelstaplers aufweisen, darf diese
Grenze nie überschritten werden.
questo limite.
Prima della messa in servizio di ogni Before putting any type of accessory Vor Inbetriebsetzung jedes Zubehörteils
tipo di accessorio sul carrello elevatore into operation on the fork-lift truck auf dem Hubwagen ist die Kompatibilität
accertarsi della compatibilità della check the machine’s compatibility zwischen Maschine und Eichung des
macchina e della taratura del sistema di and the calibration of the safety system sich auf das verwendete Zubehörteil
with regard to the accessory used. beziehenden Sicherheitssystems
sicurezza inerente all’accessorio
sicherzustellen.
utilizzato.
MONTAGGIO DELL’ACCESSORIO HOW TO MOUNT THE ACCESSORY MONTAGE DES ZUBEHÖRTEILS MIT
CON BLOCCO MANUALE WITH MANUAL LOCK MANUELLER VERRIEGELUNG
Mantenete puliti gli innesti rapidi e Keep the snap couplings clean and pro- Halten Sie die Schnellkupplungen stets
proteggete gli orifizi non utilizzati con gli tect the unused orifices with the caps sauber und schützen Sie nicht verwen-
appositi tappi. provided. dete Öffnungen durch entsprechende
Stopfen.
D
A B C
5
MONTAGGIO DELL’ACCESSORIO CON ACCESSORY WITHOUT HYDRAULIC MONTAGE DES ZUBEHÖRTEILS MIT
BLOCCO IDRAULICO (OPZIONAL). SYSTEM AND HYDRAULIC LOCKING HYDRAULISCHER VERRIEGELUNG
(OPTIONAL).
Presa dell’accessorio Einsetzen des Anbaugeräts
Engaging the accessory
- Verificare che l’accessorio sia in una - Vergewissern Sie sich, daß das
posizione che faciliti l’aggancio - Check that the accessory is in a position Anbaugerät sich in einer Stellung
dell’attacco rapido. Nel caso in cui which simplifies connection of the snap befindet, in der die Schnellkupplung
fosse male orientato, prendete le coupling. If it is badly positioned, take leicht einrasten kann. Sollte das Gerät
precauzioni necessarie per spostarlo in the necessary precautions to move it in schlecht ausgerichtet sein, ergreifen
condizioni di massima sicurezza. the conditions of maximum safety. Sie alle erforderlichen
- Verificare che le aste del martinetto di - Check that the rods of the locking Vorsichtsmaßnahmen, um es in aller
bloccaggio siano rientrate. cylinder are retracted. Sicherheit versetzen zu können.
- Posizionare il carrello elevatore con il - Position the lift-truck with the boom - Vergewissern Sie sich, daß die Stäbe
braccio abbassato ben di fronte e lowered squarely in front of and parallel des Verriegelungszylinders
parallelo all’accessorio e inclinare to the accessory and tilt the snap eingefahren sind.
l’attacco rapido in avanti (Fig.A). coupling forward (Fig.A). - Positionieren Sie den Gabelstapler mit
- Portare l’attacco rapido sotto il tubo - Bring the snap coupling into position gesenktem Arm genau gegenüber und
d’aggancio dell’accessorio, alzare below the accessory’s connection pipe, parallel zum Anbaugerät. Neigen Sie
leggermente il braccio e inclinare raise the boom slightly and tilt the die Schnellkupplung nach vorne (Abb.A).
l’attacco stesso all’indietro per connection back to position the - Bringen Sie die Schnellkupplung unter
posizionare l’accessorio (Fig.B). accessory (Fig.B). das Kupplungsrohr des Anbaugeräts,
- Disimpegnare l’accessorio dal suolo - Raise the accessory off the ground for heben Sie den Arm leicht an und
per agevolare il bloccaggio. easier engagement. neigen Sie die Kupplung selbst nach
- Azionare il comando optional per - Operate the optional control to lock the hinten, um das Anbaugerät in Position
bloccare l’accessorio. accessory zu bringen (Abb.B).
- Heben Sie das Anbaugerät vom
Boden an, um das Einrasten zu
Bloccaggio e sbloccaggio idraulico Hydraulic locking and release vereinfachen.
(opzional) (optional) - Das Bedienelement Optional betätigen,
um das Zubehörteil zu verriegeln.
- Il bloccaggio e lo sbloccaggio di un
eventuale accessorio avviene tramite - Accessories are locked and released Hydraulische Ver- und Entriegelung
l’utilizzo del comando optional with the optional control (which can (wahlweise)
(comando che può essere azionato da be operated by a button or by the
un apposito pulsante o dal manipulator itself, depending on the - Das Ver- bzw. Entriegeln eines
manipolator stesso a seconda del tipo type of lift truck in question), by means etwaigen Zubehörteils erfolgt über die
di carrello elevatore che si possiede) of the pins which must project from the Benutzung des Bedienelements
tramite i perni che debbano fuoriuscire holes ofthe quick coupling (Fig. C). Optional (Bedienelement, das je nach
dai fori dell’attacco rapido (Fig. C). dem Hubstapler, den man besitzt, mit
einer speziellen Taste oder mit dem
Vierwegschalter betätigt werden kann)
mittels der Bolzen, die aus den
Rimozione (e posa) dell’accessorio Removing (and putting down) the Öffnungen der Schnellkupplung
accesory austreten müssen (Fig. C).
- Procedere in senso inverso a quello - Proceed in reverse direction to the Abnehmen (und Ablegen) des
della PRESA DELL’ACCESSSORIO ENGAGING THE ACCESSORY Anbaugeräts
facendo attenzione a posare il procedure, taking care to place it in a
medesimo in posizione sicura su suolo safe position on firm, flat ground. - Gehen Sie in umgekehrter Reihenfolge
compatto e piano. wie beim EINSETZEN DES
ANBAUGERÄTS vor und achten Sie
darauf, das Anbaugerät in einer
sicheren Stellung auf festem, ebenem
Untergrund abzulegen.
D
A B C
6
Bloccaggio meccanico dell’ accessorio Accessory “mecanic locking” “Mechanischen block” des zubehöres
-Bloccare il martinetto con l’apposito - Lock the cylinder with the “mecanic - Der zylynder, mit dem mechanischen
“blocco meccanico” (Fig.D), che locking” (Fig.D) that allows to not block (Abb.D), der den zubehör an
permette di non liberare release the accessory mounted on the dem hubwagen angebracht, nicht
accidentalmente l’accessorio montato truck in an accidental way: zufälling freilassen darf, fest klemmen:
sul carrello elevatore: - insert the support (Fig.D) in the - der blockbügel (Fig.D) in das
- Inserire la staffa di blocco (Fig.D) quick coupling rod cylinder side. schnellwechseleinsatz, an der seite der
nell’attacco rapido lato stelo martinetto (Ref.1- Fig.E). spindel des zylinder, eisetzen (Ref.1-
(Rif.1 Fig.E) - Fix the support with the locking screw Fig.E).
- fissare la staffa tramite la apposita vite (Ref. 1 - Fig.F). - Der blockbügel mit die blockschraube
di blocco (Rif.2 Fig.F) festklemmen (Ref. 2 - Fig.F).
Assicurarsi che i perni di bloccaggio Make sure that the locking pins have Sicherstellen, dass die
siano fuoriusciti e abbiano bloccato l’ac- projected and that they have locked the Verriegelungsbolzen ausgetreten sind
cessorio prima di iniziare qualsiasi accessory before starting work. und das Zubehörteil
manovra di lavoro. verriegelt haben, bevor man irgendein
Arbeitsmanöver beginnt.
Attenzione a non sbloccare Make sure that you do not unhitch the Achtung! Das Zubehörteil nicht
accidentalmente l’accessorio compiendo accessory by accidentally making the unbeabsichtigt entriegeln, indem man
la manovra di sblocco durante il lavoro. release manoeuvre as you work. If you während der Arbeit eine Entriegelung
Se si hanno dubbi sull’effettivo bloccag- are not sure that the accessory is secu- vornimmt. Wenn man Zweifel über die
gio dell’accessorio fermare la macchina rely locked in place, stop the machine effektive Verriegelung des Zubehörteils
e and check that the pins have projected. hat, die Maschine anhalten und anhand
controllare visivamente la fuiriuscita dei Repeat the locking operation if this is einer Sichtprüfung feststellen, dass die
perni ripetendo, se necessario not the case. Bolzen ausgetreten sind, um den
l’operazione di bloccaggio. Verriegelungsvorgang bei Bedarf zu
wiederholen.
Attenzione: con l’utilizzo dei cestelli è Warning: using the basket it’s necessary Mit der benutzung der korben, ist es ver-
obbligatorio montare il “blocco meccanico”. to mount the “meccanic locking”. bindlinch die mechanische blockierung
montieren.
1
1
E F
7
RIDUTTOR. ARGANO 3T 4T
OLIO SHELL TELLUS T46 250 ORE
WINDLASS REDUCER SHELL TELLUS T 46 OIL 250 HOURS
SCHMIERÖL SHELL TELLUS T46 0,25 L 1,3 L 250 STUNDEN
WIND REDUCTOR
ROTAZION. GANCIO
OLIO AT40 / 30 ORE
ROTATION HOOK AT 40 OIL / 30 HOURS
SCHMIERÖL AT40 / 30 STUNDEN
UMLAUF HAKEN
Ø 12 mm
4000 Kg CON 2 FUNI 2500 Kg TIPO DIRETTO
ARGANO 4 T IDRAULICO
672365
WINCH 4 T 4000 Kg WITH 2 ROPES 2500 Kg TYPE DIRECT 16000 daN 18 m/min HYDRAULIC 950 1440 865 4T 462 Kg
608568*
WINDE 4 T 4000 Kg MIT ZWEI SEILE 2500 Kg DIREKT TYP HYDRAULIK
x 46 m
I diagrammi di portata sono validi The load capacity diagrams are Diese Traglastdiagramme gelten
solo con il sistema di sicurezza only valid with the safety system nur bei korrekt eingestellten
regolarmente inserito. properly activated. Sicherheitssystem.
10
690790
3200 13,6 m
pos. A
Kg
MRT 1432
Forks 500 mm
690789
3200 13,8 m
pos. A
Kg
MRT 1432
Forks 500 mm
11
15,8 m
690905
pos. A
3500
Kg
MRT 1635
Forks 500 mm
13,6 m
690791
pos. A
1800
Kg
MRT 1432
Forks 500 mm
12
690907
14 m
pos. A
1800
Kg
MRT 1635
Forks 15,6 m500 mm
690906
pos. A
3200
Kg
MRT 1635
Forks 500 mm
13
A B C D
14
I diagrammi di portata sono validi The load capacity diagrams are Diese Traglastdiagramme gelten
solo con il sistema di sicurezza only valid with the safety system nur bei korrekt eingestellten
regolarmente inserito. properly activated. Sicherheitssystem.
15
14,1 m
690799
pos. D
600
Kg
MRT 1432
P 600
690798
14,3 m
pos. D
600
Kg
MRT 1432
P 600
16
690914
16,2 m
pos. D
600
Kg
MRT 1635
P 600
690800
6,8 m
pos. D
600
Kg
MRT 1432
P 600
17
690916
7,4 m
pos. D
600
Kg
MRT 1635
P 600
690915
16 m
pos. D
600
Kg
MRT 1635
P 600
18
IDRAULICO
607431
PT 600 600 Kg Ø 7 mm x 30 m 45 m/min HYDRAULIC 830 815 4027 1200 mm 290 Kg
658137*
HYDRAULIK
19
I diagrammi di portata sono validi The load capacity diagrams are Diese Traglastdiagramme gelten
solo con il sistema di sicurezza only valid with the safety system nur bei korrekt eingestellten
regolarmente inserito. properly activated. Sicherheitssystem.
20
690802
13,5 m
pos. D
600
Kg
MRT 1432
PT 600
13,7 m
690801
pos. D
600
Kg
MRT 1432
PT 600
21
690917
15,7 m
pos. D
600
Kg
MRT 1635
PT 600
690803
6,2 m
pos. D
600
Kg
MRT 1432
PT 600
22
A B C D
23
I diagrammi di portata sono validi The load capacity diagrams are Diese Traglastdiagramme gelten
solo con il sistema di sicurezza only valid with the safety system nur bei korrekt eingestellten
regolarmente inserito. properly activated. Sicherheitssystem.
24
14,1 m
708563
pos. E
1000
Kg
MRT 1432
P 1000
708564
1000 14,3 m
pos. E
Kg
MRT 1432
P 1000
25
16,2 m
708104
pos. E
1000
Kg
MRT 1635
P 1000
708562
6,8 m
pos. E
1000
Kg
MRT 1432
P 1000
26
IDRAULICO
PT 1000 672324 1000 Kg Ø 7 mm x 51 m 23 m/min HYDRAULIC 830 815 4027 1200 mm 310 Kg
HYDRAULIK
27
I diagrammi di portata sono validi The load capacity diagrams are Diese Traglastdiagramme gelten
solo con il sistema di sicurezza only valid with the safety system nur bei korrekt eingestellten
regolarmente inserito. properly activated. Sicherheitssystem.
28
13,5 m
708567
pos. E
1000
Kg
MRT 1432
PT 1000
708565
1000 13,7 m
pos. E
Kg
MRT 1432
PT1000
29
15,7 m
708325
pos. E
1000
Kg
MRT 1635
PT 1000
708566
6,2 m
pos. E
1000
Kg
MRT 1432
PT 1000
30
31
I diagrammi di portata sono validi The load capacity diagrams are Diese Traglastdiagramme gelten
solo con il sistema di sicurezza only valid with the safety system nur bei korrekt eingestellten
regolarmente inserito. properly activated. Sicherheitssystem.
32
14,1 m
690805
pos. F
1200
Kg
MRT 1432
P 1200
690804
1200 14,3 m
pos. F
Kg
MRT 1432
P 1200
33
16,2 m
690920
pos. F
1200
Kg
MRT 1635
P 1200
690806
6,8 m
pos. F
1200
Kg
MRT 1432
P 1200
34
IDRAULICO
659100 1200 Kg
PT 1200 Ø 7 mm x 51 m 23 m/min HYDRAULIC 830 868 2944 800 mm 310 Kg
659101*
HYDRAULIK
35
I diagrammi di portata sono validi The load capacity diagrams are Diese Traglastdiagramme gelten
solo con il sistema di sicurezza only valid with the safety system nur bei korrekt eingestellten
regolarmente inserito. properly activated. Sicherheitssystem.
36
690808
1200 13,3 m
pos. F
Kg
MRT 1432
PT 1200
690807
1200 13,5 m
pos. F
Kg
MRT 1432
PT 1200
37
690923
15,5 m
pos. F
1200
Kg
MRT 1635
PT 1200
690809
6m
pos. F
1200
Kg
MRT 1432
PT 1200
38
39
I diagrammi di portata sono validi The load capacity diagrams are Diese Traglastdiagramme gelten
solo con il sistema di sicurezza only valid with the safety system nur bei korrekt eingestellten
regolarmente inserito. properly activated. Sicherheitssystem.
40
690811
14,1 m
pos. G
1500
Kg
MRT 1432
P 1500
690810
14,3 m
pos. G
1500
Kg
MRT 1432
P 1500
41
709014
16,2 m
pos. G
1500
Kg
MRT 1635
P 1500
690812
6,8 m
pos. G
1200
Kg
MRT 1432
P 1500
42
RIDUTTOR. ARGANO
OLIO SHELL TELLUS T46 250 ORE
WINDLASS REDU-
SHELL TELLUS T 46 OIL 250 HOURS
CER 0,3 KG
SCHMIERÖL SHELL TELLUS T46 250 STUNDEN
WIND REDUCTOR
ROTAZION. GAN-
OLIO AT40 / 30 ORE
CIO
AT 40 OIL / 30 HOURS
ROTATION HOOK
SCHMIERÖL AT40 / 30 STUNDEN
UMLAUF HAKEN
IDRAULICO
672965 1500 Kg
PT 1500 Ø 10 mm x 30 m 23 m/min HYDRAULIC 830 868 2944 800 mm 363 Kg
672325*
HYDRAULIK
43
I diagrammi di portata sono validi The load capacity diagrams are Diese Traglastdiagramme gelten
solo con il sistema di sicurezza only valid with the safety system nur bei korrekt eingestellten
regolarmente inserito. properly activated. Sicherheitssystem.
44
690814
1500 13,3 m
pos. G
Kg
MRT 1432
PT 1500
690813
1500 13,5 m
pos. G
Kg
MRT 1432
PT 1500
45
708391
15,5 m
pos. G
1500
Kg
MRT 1635
PT 1500
690815
pos. G
1200 6m
Kg
MRT 1432
PT 1500
46
B
D
47
I diagrammi di portata sono validi The load capacity diagrams are Diese Traglastdiagramme gelten
solo con il sistema di sicurezza only valid with the safety system nur bei korrekt eingestellten
regolarmente inserito. properly activated. Sicherheitssystem.
48
708591
2000 13,9 m
pos. H
Kg
MRT 1432
P2000
708589
2000 14,1 m
pos. H
Kg
MRT 1432
P2000
49
709017
2000 16,1 m
pos. H
Kg
MRT 1635
P2000
708590
6,6 m
pos. H
1200
Kg
MRT 1432
P2000
50
B
D
A
LUBRIFICAZIONE - LUBRICATION - SCHMIERUNG
PERIODICI-
DESCRIZIONE
TA’
DESIGNATION PRODOTTO CONSIGLIATO QUANTITA’
PERIODI-
BESCHREI- RECOMMENDED PRODUCT QUANTITY
CITY
BUNG RATSAM PRODUCT MENGE
PERIODIZIT
ÄT
RIDUTTOR. ARGANO
OLIO SHELL TELLUS T46 250 ORE
WINDLASS REDU-
SHELL TELLUS T 46 OIL 250 HOURS
CER 0,3 KG
SCHMIERÖL SHELL TELLUS T46 250 STUNDEN
WIND REDUCTOR
ROTAZION. GAN-
OLIO AT40 / 30 ORE
CIO
AT 40 OIL / 30 HOURS
ROTATION HOOK
SCHMIERÖL AT40 / 30 STUNDEN
UMLAUF HAKEN
IDRAULICO
PT 2000 675511 2000 Kg Ø 7 mm x 51 m 23 m/min HYDRAULIC 830 868 2250 730 mm 387 Kg
HYDRAULIK
51
I diagrammi di portata sono validi The load capacity diagrams are Diese Traglastdiagramme gelten
solo con il sistema di sicurezza only valid with the safety system nur bei korrekt eingestellten
regolarmente inserito. properly activated. Sicherheitssystem.
52
708593
2000 13,3 m
pos. H
Kg
MRT 1432
PT2000
708592
2000 13,5 m
pos. H
Kg
MRT 1432
PT2000
53
708329
15,5 m
pos. H
2000
Kg
MRT 1635
PT 2000
708594
6m
pos. H
1200
Kg
MRT 1432
PT2000
54
C A
1200 KG 4000 KG B
55
I diagrammi di portata sono validi The load capacity diagrams are Diese Traglastdiagramme gelten
solo con il sistema di sicurezza only valid with the safety system nur bei korrekt eingestellten
regolarmente inserito. properly activated. Sicherheitssystem.
56
708578 708585
5
57
58
5
Kg Kg
708577 708587
MRT 1432 - 1635 MSeries
MRT 1432 pos. M MRT 1432 pos. M
IT
708588 708586
5
59
60
5
Kg Kg
710960 710961
MRT 1432 - 1635 MSeries
MRT 1432 - 1635 MSeries 5
IT EN DE
C
E
B
A B C D
61
I diagrammi di portata sono validi The load capacity diagrams are Diese Traglastdiagramme gelten
solo con il sistema di sicurezza only valid with the safety system nur bei korrekt eingestellten
regolarmente inserito. properly activated. Sicherheitssystem.
62
3000 13,7 m
690797
pos. Q
Kg
MRT 1432
Jib 3T
13,9 m
690795
pos. Q
3000
Kg
MRT 1432
Jib 3T
63
690911
3000 15,9 m
pos. Q
Kg
MRT 1635
Jib 3T
690796
6,5 m
pos. Q
2000
Kg
MRT 1432
Jib 3T
64
690913
7,1 m
pos. Q
1800
Kg
MRT 1635
Jib 3T
690912
3000 15,7 m
pos. Q
Kg
MRT 1635
Jib 3T
65
4000 13,7 m
708596
pos. R
Kg
MRT 1432
Jib 4T
708597
4000 13,9 m
pos. R
Kg
MRT 1432
Jib 4T
66
708574
4000 15,9 m
pos. R
Kg
MRT 1635
Jib 4T
708595
6,5 m
pos. R
2000
Kg
MRT 1432
Jib 4T
67
708576
7,1 m
pos. R
1800
Kg
MRT 1635
Jib 4T
708575
3200 15,7 m
pos. R
Kg
MRT 1635
Jib 4T
68
Q
B
A B C
a c
F FEM 3A 578097 5000 150 50 1200 104 Kg
69
A
D
B
Q
A B C D
A B C
70
D
A
A B C D
A B C
a c
71
B Q
A
D
A B D
C
A B C
F FLOTT 576017 5000 150 60 1200 141 Kg
a c
72
Q B
A B C D
A B C
a c
F FEM 3A 578097 5000 150 60 1200 141 Kg
73
I diagrammi di portata sono validi The load capacity diagrams are Diese Traglastdiagramme gelten
solo con il sistema di sicurezza only valid with the safety system nur bei korrekt eingestellten
regolarmente inserito. properly activated. Sicherheitssystem.
74
690790
3200 13,6 m
pos. A
Kg
MRT 1432
Forks 500 mm
690789
3200 13,8 m
pos. A
Kg
MRT 1432
Forks 500 mm
75
15,8 m
690905
pos. A
3500
Kg
MRT 1635
Forks 13,6 m 500 mm
690791
pos. A
1800
Kg
MRT 1432
Forks 500 mm
76
690907
14 m
pos. A
1800
Kg
MRT 1635
Forks 15,6 m 500 mm
690906
pos. A
3200
Kg
MRT 1635
Forks 500 mm
77
B
Q
78
B
Q
79
DESCRIZIONE
RIFERIMENTO LARGHEZZA IN MM CAPACITA’ PESO A VUOTO Kg.CA APERTURA BOCCHETTA
DESIGNATION
REFERENCE WINDTH MILLIMETRES CAPACITY IDLING WEIGHT KG HOSE OPENING
BESCHREIBUNG
ZEICHEN BREITE MM KAPAZITAET GEWICHT STUTZENOEFFNUNG
IDRAULICA
MIX 350 R 576943 (A) 1360 350 L 540 HYDRAULIC
HYDRAU
IDRAULICA
MIX 500 R 577115 (A) 1640 500 L 650 HYDRAULIC
HYDRAU
IDRAULICA
MIX 750 R 577117 (A) 1700 750 L 820 HYDRAULIC
HYDRAU
80
Q
B
81